Pull bugzilla-7465 into release branch

[pandora-kernel.git] / drivers / ide / Kconfig

diff --git a/drivers/ide/Kconfig b/drivers/ide/Kconfig
index 350764e..8f1fd01 100644 (file)
--- a/drivers/ide/Kconfig
+++ b/drivers/ide/Kconfig
@@ -383,6 +383,9 @@ config BLK_DEV_OFFBOARD
 config BLK_DEV_GENERIC
        tristate "Generic PCI IDE Chipset Support"
        depends on BLK_DEV_IDEPCI
+        help
+          This option provides generic support for various PCI IDE Chipsets
+          which otherwise might not be supported.
 
 config BLK_DEV_OPTI621
        tristate "OPTi 82C621 chipset enhanced support (EXPERIMENTAL)"
@@ -431,24 +434,8 @@ config BLK_DEV_IDEDMA_FORCED
 
          Generally say N here.
 
-config IDEDMA_PCI_AUTO
-       bool "Use PCI DMA by default when available"
-       ---help---
-         Prior to kernel version 2.1.112, Linux used to automatically use
-         DMA for IDE drives and chipsets which support it. Due to concerns
-         about a couple of cases where buggy hardware may have caused damage,
-         the default is now to NOT use DMA automatically. To revert to the
-         previous behaviour, say Y to this question.
-
-         If you suspect your hardware is at all flakey, say N here.
-         Do NOT email the IDE kernel people regarding this issue!
-
-         It is normally safe to answer Y to this question unless your
-         motherboard uses a VIA VP2 chipset, in which case you should say N.
-
 config IDEDMA_ONLYDISK
        bool "Enable DMA only for disks "
-       depends on IDEDMA_PCI_AUTO
        help
          This is used if you know your ATAPI Devices are going to fail DMA
          Transfers.
@@ -766,6 +753,14 @@ config BLK_DEV_TC86C001
        help
        This driver adds support for Toshiba TC86C001 GOKU-S chip.
 
+config BLK_DEV_CELLEB
+       tristate "Toshiba's Cell Reference Set IDE support"
+       depends on PPC_CELLEB
+       help
+         This driver provides support for the built-in IDE controller on
+         Toshiba Cell Reference Board.
+         If unsure, say Y.
+
 endif
 
 config BLK_DEV_IDE_PMAC
@@ -797,14 +792,6 @@ config BLK_DEV_IDEDMA_PMAC
          to transfer data to and from memory.  Saying Y is safe and improves
          performance.
 
-config BLK_DEV_IDE_CELLEB
-       bool "Toshiba's Cell Reference Set IDE support"
-       depends on PPC_CELLEB
-       help
-         This driver provides support for the built-in IDE controller on
-         Toshiba Cell Reference Board.
-         If unsure, say Y.
-
 config BLK_DEV_IDE_SWARM
        tristate "IDE for Sibyte evaluation boards"
        depends on SIBYTE_SB1xxx_SOC
@@ -848,19 +835,6 @@ config BLK_DEV_IDEDMA_ICS
          Say Y here if you want to add DMA (Direct Memory Access) support to
          the ICS IDE driver.
 
-config IDEDMA_ICS_AUTO
-       bool "Use ICS DMA by default"
-       depends on BLK_DEV_IDEDMA_ICS
-       help
-         Prior to kernel version 2.1.112, Linux used to automatically use
-         DMA for IDE drives and chipsets which support it. Due to concerns
-         about a couple of cases where buggy hardware may have caused damage,
-         the default is now to NOT use DMA automatically. To revert to the
-         previous behaviour, say Y to this question.
-
-         If you suspect your hardware is at all flakey, say N here.
-         Do NOT email the IDE kernel people regarding this issue!
-
 config BLK_DEV_IDE_RAPIDE
        tristate "RapIDE interface support"
        depends on ARM && ARCH_ACORN
@@ -1020,7 +994,7 @@ config BLK_DEV_4DRIVES
 config BLK_DEV_ALI14XX
        tristate "ALI M14xx support"
        help
-         This driver is enabled at runtime using the "ide0=ali14xx" kernel
+         This driver is enabled at runtime using the "ali14xx.probe" kernel
          boot parameter.  It enables support for the secondary IDE interface
          of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster
          I/O speeds to be set as well.  See the files
@@ -1030,7 +1004,7 @@ config BLK_DEV_ALI14XX
 config BLK_DEV_DTC2278
        tristate "DTC-2278 support"
        help
-         This driver is enabled at runtime using the "ide0=dtc2278" kernel
+         This driver is enabled at runtime using the "dtc2278.probe" kernel
          boot parameter. It enables support for the secondary IDE interface
          of the DTC-2278 card, and permits faster I/O speeds to be set as
          well. See the <file:Documentation/ide.txt> and
@@ -1039,7 +1013,7 @@ config BLK_DEV_DTC2278
 config BLK_DEV_HT6560B
        tristate "Holtek HT6560B support"
        help
-         This driver is enabled at runtime using the "ide0=ht6560b" kernel
+         This driver is enabled at runtime using the "ht6560b.probe" kernel
          boot parameter. It enables support for the secondary IDE interface
          of the Holtek card, and permits faster I/O speeds to be set as well.
          See the <file:Documentation/ide.txt> and
@@ -1048,7 +1022,7 @@ config BLK_DEV_HT6560B
 config BLK_DEV_QD65XX
        tristate "QDI QD65xx support"
        help
-         This driver is enabled at runtime using the "ide0=qd65xx" kernel
+         This driver is enabled at runtime using the "qd65xx.probe" kernel
          boot parameter.  It permits faster I/O speeds to be set.  See the
          <file:Documentation/ide.txt> and <file:drivers/ide/legacy/qd65xx.c> for
          more info.
@@ -1056,7 +1030,7 @@ config BLK_DEV_QD65XX
 config BLK_DEV_UMC8672
        tristate "UMC-8672 support"
        help
-         This driver is enabled at runtime using the "ide0=umc8672" kernel
+         This driver is enabled at runtime using the "umc8672.probe" kernel
          boot parameter. It enables support for the secondary IDE interface
          of the UMC-8672, and permits faster I/O speeds to be set as well.
          See the files <file:Documentation/ide.txt> and
@@ -1083,9 +1057,6 @@ config IDEDMA_IVB
 
          It is normally safe to answer Y; however, the default is N.
 
-config IDEDMA_AUTO
-       def_bool IDEDMA_PCI_AUTO || IDEDMA_ICS_AUTO
-
 endif
 
 config BLK_DEV_HD_ONLY