If unsure, say Y.
config IDEDISK_MULTI_MODE
- bool "Use multi-mode by default"
- help
- If you get this error, try to say Y here:
+ bool "Use multiple sector mode for Programmed Input/Output by default"
+ help
+ This setting is irrelevant for most IDE disks, with direct memory
+ access, to which multiple sector mode does not apply. Multiple sector
+ mode is a feature of most modern IDE hard drives, permitting the
+ transfer of multiple sectors per Programmed Input/Output interrupt,
+ rather than the usual one sector per interrupt. When this feature is
+ enabled, it can reduce operating system overhead for disk Programmed
+ Input/Output. On some systems, it also can increase the data
+ throughput of Programmed Input/Output. Some drives, however, seemed
+ to run slower with multiple sector mode enabled. Some drives claimed
+ to support multiple sector mode, but lost data at some settings.
+ Under rare circumstances, such failures could result in massive
+ filesystem corruption.
+
+ If you get the following error, try to say Y here:
hda: set_multmode: status=0x51 { DriveReady SeekComplete Error }
hda: set_multmode: error=0x04 { DriveStatusError }
CD-ROM drive, you can say N to all other CD-ROM options, but be sure
to say Y or M to "ISO 9660 CD-ROM file system support".
- Note that older versions of LILO (LInux LOader) cannot properly deal
- with IDE/ATAPI CD-ROMs, so install LILO 16 or higher, available from
- <http://lilo.go.dyndns.org/>.
-
To compile this driver as a module, choose M here: the
module will be called ide-cd.
config IDE_GENERIC
tristate "generic/default IDE chipset support"
- default H8300
help
If unsure, say N.
If unsure, say N.
config BLK_DEV_CMD640
- bool "CMD640 chipset bugfix/support"
+ tristate "CMD640 chipset bugfix/support"
depends on X86
---help---
The CMD-Technologies CMD640 IDE chip is used on many common 486 and
Otherwise say N.
config BLK_DEV_IDEPNP
- bool "PNP EIDE support"
+ tristate "PNP EIDE support"
depends on PNP
- select IDE_GENERIC
help
If you have a PnP (Plug and Play) compatible EIDE card and
would like the kernel to automatically detect and activate
config BLK_DEV_IDEPCI
bool
-config IDEPCI_SHARE_IRQ
- bool "Sharing PCI IDE interrupts support"
- depends on BLK_DEV_IDEPCI
+config IDEPCI_PCIBUS_ORDER
+ bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)"
+ depends on BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ default y
help
- Some ATA/IDE chipsets have hardware support which allows for
- sharing a single IRQ with other cards. To enable support for
- this in the ATA/IDE driver, say Y here.
+ Probe IDE PCI devices in the order in which they appear on the
+ PCI bus (i.e. 00:1f.1 PCI device before 02:01.0 PCI device)
+ instead of the order in which IDE PCI host drivers are loaded.
- It is safe to say Y to this question, in most cases.
- If unsure, say N.
+ Please note that this method of assuring stable naming of
+ IDE devices is unreliable and use other means for achieving
+ it (i.e. udev).
-config IDEPCI_PCIBUS_ORDER
- def_bool BLK_DEV_IDE=y && BLK_DEV_IDEPCI
+ If in doubt, say N.
+# TODO: split it on per host driver config options (or module parameters)
config BLK_DEV_OFFBOARD
- bool "Boot off-board chipsets first support"
- depends on BLK_DEV_IDEPCI
+ bool "Boot off-board chipsets first support (DEPRECATED)"
+ depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT34X || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001)
help
Normally, IDE controllers built into the motherboard (on-board
controllers) are assigned to ide0 and ide1 while those on add-in PCI
Note that, if you do this, the order of the hd* devices will be
rearranged which may require modification of fstab and other files.
+ Please also note that this method of assuring stable naming of
+ IDE devices is unreliable and use other means for achieving it
+ (i.e. udev).
+
If in doubt, say N.
config BLK_DEV_GENERIC
config BLK_DEV_AMD74XX
tristate "AMD and nVidia IDE support"
+ depends on !ARM
select BLK_DEV_IDEDMA_PCI
help
This driver adds explicit support for AMD-7xx and AMD-8111 chips
config BLK_DEV_SGIIOC4
tristate "Silicon Graphics IOC4 chipset ATA/ATAPI support"
depends on (IA64_SGI_SN2 || IA64_GENERIC) && SGI_IOC4
- select IDEPCI_SHARE_IRQ
select BLK_DEV_IDEDMA_PCI
help
This driver adds PIO & MultiMode DMA-2 support for the SGI IOC4
endif
config BLK_DEV_IDE_PMAC
- bool "Builtin PowerMac IDE support"
+ tristate "Builtin PowerMac IDE support"
depends on PPC_PMAC && IDE=y && BLK_DEV_IDE=y
help
This driver provides support for the built-in IDE controller on
depends on BLK_DEV_IDE_AU1XXX
config IDE_ARM
- def_bool ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
- select IDE_GENERIC
+ tristate "ARM IDE support"
+ depends on ARM && (ARCH_CLPS7500 || ARCH_RPC || ARCH_SHARK)
+ default y
config BLK_DEV_IDE_ICSIDE
tristate "ICS IDE interface support"
Say Y here if you want to support the onboard IDE channels on the
Simtec BAST or the Thorcom VR1000
+config ETRAX_IDE
+ tristate "ETRAX IDE support"
+ depends on CRIS && BROKEN
+ select BLK_DEV_IDEDMA
+ help
+ Enables the ETRAX IDE driver.
+
+ You can't use parallel ports or SCSI ports at the same time.
+
+config ETRAX_IDE_DELAY
+ int "Delay for drives to regain consciousness"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default 15
+ help
+ Number of seconds to wait for IDE drives to spin up after an IDE
+ reset.
+
+choice
+ prompt "IDE reset pin"
+ depends on ETRAX_IDE && ETRAX_ARCH_V10
+ default ETRAX_IDE_PB7_RESET
+
+config ETRAX_IDE_PB7_RESET
+ bool "Port_PB_Bit_7"
+ help
+ IDE reset on pin 7 on port B
+
+config ETRAX_IDE_G27_RESET
+ bool "Port_G_Bit_27"
+ help
+ IDE reset on pin 27 on port G
+
+endchoice
+
+config IDE_H8300
+ tristate "H8300 IDE support"
+ depends on H8300
+ default y
+ help
+ Enables the H8300 IDE driver.
+
config BLK_DEV_GAYLE
- bool "Amiga Gayle IDE interface support"
+ tristate "Amiga Gayle IDE interface support"
depends on AMIGA
- select IDE_GENERIC
help
This is the IDE driver for the Amiga Gayle IDE interface. It supports
both the `A1200 style' and `A4000 style' of the Gayle IDE interface,
runtime using the "ide=doubler" kernel boot parameter.
config BLK_DEV_BUDDHA
- bool "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
+ tristate "Buddha/Catweasel/X-Surf IDE interface support (EXPERIMENTAL)"
depends on ZORRO && EXPERIMENTAL
- select IDE_GENERIC
help
This is the IDE driver for the IDE interfaces on the Buddha,
Catweasel and X-Surf expansion boards. It supports up to two interfaces
to one of its IDE interfaces.
config BLK_DEV_FALCON_IDE
- bool "Falcon IDE interface support"
+ tristate "Falcon IDE interface support"
depends on ATARI
- select IDE_GENERIC
help
This is the IDE driver for the builtin IDE interface on the Atari
Falcon. Say Y if you have a Falcon and want to use IDE devices (hard
interface.
config BLK_DEV_MAC_IDE
- bool "Macintosh Quadra/Powerbook IDE interface support"
+ tristate "Macintosh Quadra/Powerbook IDE interface support"
depends on MAC
- select IDE_GENERIC
help
This is the IDE driver for the builtin IDE interface on some m68k
Macintosh models. It supports both the `Quadra style' (used in
builtin IDE interface.
config BLK_DEV_Q40IDE
- bool "Q40/Q60 IDE interface support"
+ tristate "Q40/Q60 IDE interface support"
depends on Q40
- select IDE_GENERIC
help
Enable the on-board IDE controller in the Q40/Q60. This should
normally be on; disable it only if you are running a custom hard
drive subsystem through an expansion card.
config BLK_DEV_MPC8xx_IDE
- bool "MPC8xx IDE support"
- depends on 8xx && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
- select IDE_GENERIC
+ tristate "MPC8xx IDE support"
+ depends on 8xx && (LWMON || IVMS8 || IVML24 || TQM8xxL) && IDE=y && BLK_DEV_IDE=y && !PPC_MERGE
help
This option provides support for IDE on Motorola MPC8xx Systems.
Please see 'Type of MPC8xx IDE interface' for details.
config BLK_DEV_IDEDMA
def_bool BLK_DEV_IDEDMA_PCI || BLK_DEV_IDEDMA_PMAC || BLK_DEV_IDEDMA_ICS || BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
+config IDE_ARCH_OBSOLETE_INIT
+ def_bool ALPHA || (ARM && !ARCH_L7200) || BLACKFIN || X86 || IA64 || M32R || MIPS || PARISC || PPC || (SUPERH64 && BLK_DEV_IDEPCI) || SPARC
+
endif
config BLK_DEV_HD_ONLY
git.openpandora.org / pandora-kernel.git / blobdiff