#define _TRANSCODER(tran, a, b) ((a) + (tran)*((b)-(a)))
#define _PORT(port, a, b) ((a) + (port)*((b)-(a)))
-#define _PIPE3(pipe, a, b, c) (pipe < 2 ? _PIPE(pipe, a, b) : c)
-#define _PORT3(port, a, b, c) (port < 2 ? _PORT(port, a, b) : c)
+#define _PIPE3(pipe, a, b, c) ((pipe) == PIPE_A ? (a) : \
+ (pipe) == PIPE_B ? (b) : (c))
#define _MASKED_BIT_ENABLE(a) (((a) << 16) | (a))
#define _MASKED_BIT_DISABLE(a) ((a) << 16)
#define PUNIT_FUSE_BUS2 0xf6 /* bits 47:40 */
#define PUNIT_FUSE_BUS1 0xf5 /* bits 55:48 */
+#define PUNIT_GPU_STATUS_REG 0xdb
+#define PUNIT_GPU_STATUS_MAX_FREQ_SHIFT 16
+#define PUNIT_GPU_STATUS_MAX_FREQ_MASK 0xff
+#define PUNIT_GPU_STATIS_GFX_MIN_FREQ_SHIFT 8
+#define PUNIT_GPU_STATUS_GFX_MIN_FREQ_MASK 0xff
+
+#define PUNIT_GPU_DUTYCYCLE_REG 0xdf
+#define PUNIT_GPU_DUTYCYCLE_RPE_FREQ_SHIFT 8
+#define PUNIT_GPU_DUTYCYCLE_RPE_FREQ_MASK 0xff
+
#define IOSF_NC_FB_GFX_FREQ_FUSE 0x1c
#define FB_GFX_MAX_FREQ_FUSE_SHIFT 3
#define FB_GFX_MAX_FREQ_FUSE_MASK 0x000007f8
#define DSI_PLL_M1_DIV_MASK (0x1ff << 0)
#define CCK_DISPLAY_CLOCK_CONTROL 0x6b
-/*
- * DPIO - a special bus for various display related registers to hide behind
+/**
+ * DOC: DPIO
+ *
+ * VLV and CHV have slightly peculiar display PHYs for driving DP/HDMI
+ * ports. DPIO is the name given to such a display PHY. These PHYs
+ * don't follow the standard programming model using direct MMIO
+ * registers, and instead their registers must be accessed trough IOSF
+ * sideband. VLV has one such PHY for driving ports B and C, and CHV
+ * adds another PHY for driving port D. Each PHY responds to specific
+ * IOSF-SB port.
+ *
+ * Each display PHY is made up of one or two channels. Each channel
+ * houses a common lane part which contains the PLL and other common
+ * logic. CH0 common lane also contains the IOSF-SB logic for the
+ * Common Register Interface (CRI) ie. the DPIO registers. CRI clock
+ * must be running when any DPIO registers are accessed.
+ *
+ * In addition to having their own registers, the PHYs are also
+ * controlled through some dedicated signals from the display
+ * controller. These include PLL reference clock enable, PLL enable,
+ * and CRI clock selection, for example.
+ *
+ * Eeach channel also has two splines (also called data lanes), and
+ * each spline is made up of one Physical Access Coding Sub-Layer
+ * (PCS) block and two TX lanes. So each channel has two PCS blocks
+ * and four TX lanes. The TX lanes are used as DP lanes or TMDS
+ * data/clock pairs depending on the output type.
+ *
+ * Additionally the PHY also contains an AUX lane with AUX blocks
+ * for each channel. This is used for DP AUX communication, but
+ * this fact isn't really relevant for the driver since AUX is
+ * controlled from the display controller side. No DPIO registers
+ * need to be accessed during AUX communication,
+ *
+ * Generally the common lane corresponds to the pipe and
+ * the spline (PCS/TX) correponds to the port.
+ *
+ * For dual channel PHY (VLV/CHV):
+ *
+ * pipe A == CMN/PLL/REF CH0
+ *
+ * pipe B == CMN/PLL/REF CH1
*
- * DPIO is VLV only.
+ * port B == PCS/TX CH0
*
- * Note: digital port B is DDI0, digital pot C is DDI1
+ * port C == PCS/TX CH1
+ *
+ * This is especially important when we cross the streams
+ * ie. drive port B with pipe B, or port C with pipe A.
+ *
+ * For single channel PHY (CHV):
+ *
+ * pipe C == CMN/PLL/REF CH0
+ *
+ * port D == PCS/TX CH0
+ *
+ * Note: digital port B is DDI0, digital port C is DDI1,
+ * digital port D is DDI2
+ */
+/*
+ * Dual channel PHY (VLV/CHV)
+ * ---------------------------------
+ * | CH0 | CH1 |
+ * | CMN/PLL/REF | CMN/PLL/REF |
+ * |---------------|---------------| Display PHY
+ * | PCS01 | PCS23 | PCS01 | PCS23 |
+ * |-------|-------|-------|-------|
+ * |TX0|TX1|TX2|TX3|TX0|TX1|TX2|TX3|
+ * ---------------------------------
+ * | DDI0 | DDI1 | DP/HDMI ports
+ * ---------------------------------
+ *
+ * Single channel PHY (CHV)
+ * -----------------
+ * | CH0 |
+ * | CMN/PLL/REF |
+ * |---------------| Display PHY
+ * | PCS01 | PCS23 |
+ * |-------|-------|
+ * |TX0|TX1|TX2|TX3|
+ * -----------------
+ * | DDI2 | DP/HDMI port
+ * -----------------
*/
#define DPIO_DEVFN 0
#define DPIO_PCS_TX_LANE1_RESET (1<<7)
#define VLV_PCS_DW0(ch) _PORT(ch, _VLV_PCS_DW0_CH0, _VLV_PCS_DW0_CH1)
+#define _VLV_PCS01_DW0_CH0 0x200
+#define _VLV_PCS23_DW0_CH0 0x400
+#define _VLV_PCS01_DW0_CH1 0x2600
+#define _VLV_PCS23_DW0_CH1 0x2800
+#define VLV_PCS01_DW0(ch) _PORT(ch, _VLV_PCS01_DW0_CH0, _VLV_PCS01_DW0_CH1)
+#define VLV_PCS23_DW0(ch) _PORT(ch, _VLV_PCS23_DW0_CH0, _VLV_PCS23_DW0_CH1)
+
#define _VLV_PCS_DW1_CH0 0x8204
#define _VLV_PCS_DW1_CH1 0x8404
+#define CHV_PCS_REQ_SOFTRESET_EN (1<<23)
#define DPIO_PCS_CLK_CRI_RXEB_EIOS_EN (1<<22)
#define DPIO_PCS_CLK_CRI_RXDIGFILTSG_EN (1<<21)
#define DPIO_PCS_CLK_DATAWIDTH_SHIFT (6)
#define DPIO_PCS_CLK_SOFT_RESET (1<<5)
#define VLV_PCS_DW1(ch) _PORT(ch, _VLV_PCS_DW1_CH0, _VLV_PCS_DW1_CH1)
+#define _VLV_PCS01_DW1_CH0 0x204
+#define _VLV_PCS23_DW1_CH0 0x404
+#define _VLV_PCS01_DW1_CH1 0x2604
+#define _VLV_PCS23_DW1_CH1 0x2804
+#define VLV_PCS01_DW1(ch) _PORT(ch, _VLV_PCS01_DW1_CH0, _VLV_PCS01_DW1_CH1)
+#define VLV_PCS23_DW1(ch) _PORT(ch, _VLV_PCS23_DW1_CH0, _VLV_PCS23_DW1_CH1)
+
#define _VLV_PCS_DW8_CH0 0x8220
#define _VLV_PCS_DW8_CH1 0x8420
+#define CHV_PCS_USEDCLKCHANNEL_OVRRIDE (1 << 20)
+#define CHV_PCS_USEDCLKCHANNEL (1 << 21)
#define VLV_PCS_DW8(ch) _PORT(ch, _VLV_PCS_DW8_CH0, _VLV_PCS_DW8_CH1)
#define _VLV_PCS01_DW8_CH0 0x0220
#define DPIO_PCS_SWING_CALC_TX1_TX3 (1<<31)
#define CHV_PCS_DW10(ch) _PORT(ch, _CHV_PCS_DW10_CH0, _CHV_PCS_DW10_CH1)
+#define _VLV_PCS01_DW10_CH0 0x0228
+#define _VLV_PCS23_DW10_CH0 0x0428
+#define _VLV_PCS01_DW10_CH1 0x2628
+#define _VLV_PCS23_DW10_CH1 0x2828
+#define VLV_PCS01_DW10(port) _PORT(port, _VLV_PCS01_DW10_CH0, _VLV_PCS01_DW10_CH1)
+#define VLV_PCS23_DW10(port) _PORT(port, _VLV_PCS23_DW10_CH0, _VLV_PCS23_DW10_CH1)
+
#define _VLV_PCS_DW11_CH0 0x822c
#define _VLV_PCS_DW11_CH1 0x842c
#define VLV_PCS_DW11(ch) _PORT(ch, _VLV_PCS_DW11_CH0, _VLV_PCS_DW11_CH1)
#define DPIO_CHV_PROP_COEFF_SHIFT 0
#define CHV_PLL_DW6(ch) _PIPE(ch, _CHV_PLL_DW6_CH0, _CHV_PLL_DW6_CH1)
+#define _CHV_CMN_DW5_CH0 0x8114
+#define CHV_BUFRIGHTENA1_DISABLE (0 << 20)
+#define CHV_BUFRIGHTENA1_NORMAL (1 << 20)
+#define CHV_BUFRIGHTENA1_FORCE (3 << 20)
+#define CHV_BUFRIGHTENA1_MASK (3 << 20)
+#define CHV_BUFLEFTENA1_DISABLE (0 << 22)
+#define CHV_BUFLEFTENA1_NORMAL (1 << 22)
+#define CHV_BUFLEFTENA1_FORCE (3 << 22)
+#define CHV_BUFLEFTENA1_MASK (3 << 22)
+
#define _CHV_CMN_DW13_CH0 0x8134
#define _CHV_CMN_DW0_CH1 0x8080
#define DPIO_CHV_S1_DIV_SHIFT 21
#define _CHV_CMN_DW1_CH1 0x8084
#define DPIO_AFC_RECAL (1 << 14)
#define DPIO_DCLKP_EN (1 << 13)
+#define CHV_BUFLEFTENA2_DISABLE (0 << 17) /* CL2 DW1 only */
+#define CHV_BUFLEFTENA2_NORMAL (1 << 17) /* CL2 DW1 only */
+#define CHV_BUFLEFTENA2_FORCE (3 << 17) /* CL2 DW1 only */
+#define CHV_BUFLEFTENA2_MASK (3 << 17) /* CL2 DW1 only */
+#define CHV_BUFRIGHTENA2_DISABLE (0 << 19) /* CL2 DW1 only */
+#define CHV_BUFRIGHTENA2_NORMAL (1 << 19) /* CL2 DW1 only */
+#define CHV_BUFRIGHTENA2_FORCE (3 << 19) /* CL2 DW1 only */
+#define CHV_BUFRIGHTENA2_MASK (3 << 19) /* CL2 DW1 only */
#define CHV_CMN_DW14(ch) _PIPE(ch, _CHV_CMN_DW14_CH0, _CHV_CMN_DW1_CH1)
+#define _CHV_CMN_DW19_CH0 0x814c
+#define _CHV_CMN_DW6_CH1 0x8098
+#define CHV_CMN_USEDCLKCHANNEL (1 << 13)
+#define CHV_CMN_DW19(ch) _PIPE(ch, _CHV_CMN_DW19_CH0, _CHV_CMN_DW6_CH1)
+
#define CHV_CMN_DW30 0x8178
#define DPIO_LRC_BYPASS (1 << 3)
#define _TXLANE(ch, lane, offset) ((ch ? 0x2400 : 0) + \
(lane) * 0x200 + (offset))
+#define CHV_TX_DW0(ch, lane) _TXLANE(ch, lane, 0x80)
+#define CHV_TX_DW1(ch, lane) _TXLANE(ch, lane, 0x84)
+#define CHV_TX_DW2(ch, lane) _TXLANE(ch, lane, 0x88)
+#define CHV_TX_DW3(ch, lane) _TXLANE(ch, lane, 0x8c)
+#define CHV_TX_DW4(ch, lane) _TXLANE(ch, lane, 0x90)
+#define CHV_TX_DW5(ch, lane) _TXLANE(ch, lane, 0x94)
+#define CHV_TX_DW6(ch, lane) _TXLANE(ch, lane, 0x98)
+#define CHV_TX_DW7(ch, lane) _TXLANE(ch, lane, 0x9c)
+#define CHV_TX_DW8(ch, lane) _TXLANE(ch, lane, 0xa0)
+#define CHV_TX_DW9(ch, lane) _TXLANE(ch, lane, 0xa4)
+#define CHV_TX_DW10(ch, lane) _TXLANE(ch, lane, 0xa8)
#define CHV_TX_DW11(ch, lane) _TXLANE(ch, lane, 0xac)
#define DPIO_FRC_LATENCY_SHFIT 8
#define CHV_TX_DW14(ch, lane) _TXLANE(ch, lane, 0xb8)
#define SANDYBRIDGE_FENCE_PITCH_SHIFT 32
#define GEN7_FENCE_MAX_PITCH_VAL 0x0800
+
/* control register for cpu gtt access */
#define TILECTL 0x101000
#define TILECTL_SWZCTL (1 << 0)
#define IMR 0x020a8
#define ISR 0x020ac
#define VLV_GUNIT_CLOCK_GATE (VLV_DISPLAY_BASE + 0x2060)
+#define GINT_DIS (1<<22)
#define GCFG_DIS (1<<8)
#define VLV_GUNIT_CLOCK_GATE2 (VLV_DISPLAY_BASE + 0x2064)
#define VLV_IIR_RW (VLV_DISPLAY_BASE + 0x2084)
#define VLV_IMR (VLV_DISPLAY_BASE + 0x20a8)
#define VLV_ISR (VLV_DISPLAY_BASE + 0x20ac)
#define VLV_PCBR (VLV_DISPLAY_BASE + 0x2120)
+#define VLV_PCBR_ADDR_SHIFT 12
+
#define DISPLAY_PLANE_FLIP_PENDING(plane) (1<<(11-(plane))) /* A and B only */
#define EIR 0x020b0
#define EMR 0x020b4
#define I915_ERROR_INSTRUCTION (1<<0)
#define INSTPM 0x020c0
#define INSTPM_SELF_EN (1<<12) /* 915GM only */
-#define INSTPM_AGPBUSY_DIS (1<<11) /* gen3: when disabled, pending interrupts
+#define INSTPM_AGPBUSY_INT_EN (1<<11) /* gen3: when disabled, pending interrupts
will not assert AGPBUSY# and will only
be delivered when out of C3. */
#define INSTPM_FORCE_ORDERING (1<<7) /* GEN6+ */
#define MI_ARB_DISPLAY_PRIORITY_A_B (0 << 0) /* display A > display B */
#define MI_ARB_DISPLAY_PRIORITY_B_A (1 << 0) /* display B > display A */
+#define MI_STATE 0x020e4 /* gen2 only */
+#define MI_AGPBUSY_INT_EN (1 << 1) /* 85x only */
+#define MI_AGPBUSY_830_MODE (1 << 0) /* 85x only */
+
#define CACHE_MODE_0 0x02120 /* 915+ only */
#define CM0_PIPELINED_RENDER_FLUSH_DISABLE (1<<8)
#define CM0_IZ_OPT_DISABLE (1<<6)
#define GEN6_RC_SLEEP_PSMI_CONTROL 0x2050
#define GEN8_RC_SEMA_IDLE_MSG_DISABLE (1 << 12)
+#define GEN8_FF_DOP_CLOCK_GATE_DISABLE (1<<10)
#define GEN6_BSD_SLEEP_PSMI_CONTROL 0x12050
#define GEN6_BSD_SLEEP_MSG_DISABLE (1 << 0)
#define GMBUS_PORT_SSC 1
#define GMBUS_PORT_VGADDC 2
#define GMBUS_PORT_PANEL 3
+#define GMBUS_PORT_DPD_CHV 3 /* HDMID_CHV */
#define GMBUS_PORT_DPC 4 /* HDMIC */
#define GMBUS_PORT_DPB 5 /* SDVO, HDMIB */
#define GMBUS_PORT_DPD 6 /* HDMID */
/*
* Clock control & power management
*/
-#define DPLL_A_OFFSET 0x6014
-#define DPLL_B_OFFSET 0x6018
-#define CHV_DPLL_C_OFFSET 0x6030
-#define DPLL(pipe) (dev_priv->info.dpll_offsets[pipe] + \
- dev_priv->info.display_mmio_offset)
+#define _DPLL_A (dev_priv->info.display_mmio_offset + 0x6014)
+#define _DPLL_B (dev_priv->info.display_mmio_offset + 0x6018)
+#define _CHV_DPLL_C (dev_priv->info.display_mmio_offset + 0x6030)
+#define DPLL(pipe) _PIPE3((pipe), _DPLL_A, _DPLL_B, _CHV_DPLL_C)
#define VGA0 0x6000
#define VGA1 0x6004
#define SDVO_MULTIPLIER_SHIFT_HIRES 4
#define SDVO_MULTIPLIER_SHIFT_VGA 0
-#define DPLL_A_MD_OFFSET 0x601c /* 965+ only */
-#define DPLL_B_MD_OFFSET 0x6020 /* 965+ only */
-#define CHV_DPLL_C_MD_OFFSET 0x603c
-#define DPLL_MD(pipe) (dev_priv->info.dpll_md_offsets[pipe] + \
- dev_priv->info.display_mmio_offset)
+#define _DPLL_A_MD (dev_priv->info.display_mmio_offset + 0x601c)
+#define _DPLL_B_MD (dev_priv->info.display_mmio_offset + 0x6020)
+#define _CHV_DPLL_C_MD (dev_priv->info.display_mmio_offset + 0x603c)
+#define DPLL_MD(pipe) _PIPE3((pipe), _DPLL_A_MD, _DPLL_B_MD, _CHV_DPLL_C_MD)
/*
* UDI pixel divider, controlling how many pixels are stuffed into a packet.
# define DPIOUNIT_CLOCK_GATE_DISABLE (1 << 6) /* 915-945 */
# define OVFUNIT_CLOCK_GATE_DISABLE (1 << 5)
# define OVBUNIT_CLOCK_GATE_DISABLE (1 << 4)
-/**
+/*
* This bit must be set on the 830 to prevent hangs when turning off the
* overlay scaler.
*/
# define COLOR_CALCULATOR_CLOCK_GATE_DISABLE (1 << 7)
# define MOTION_COMP_CLOCK_GATE_DISABLE (1 << 6)
# define MAG_CLOCK_GATE_DISABLE (1 << 5)
-/** This bit must be unset on 855,865 */
+/* This bit must be unset on 855,865 */
# define MECI_CLOCK_GATE_DISABLE (1 << 4)
# define DCMP_CLOCK_GATE_DISABLE (1 << 3)
# define MEC_CLOCK_GATE_DISABLE (1 << 2)
# define MECO_CLOCK_GATE_DISABLE (1 << 1)
-/** This bit must be set on 855,865. */
+/* This bit must be set on 855,865. */
# define SV_CLOCK_GATE_DISABLE (1 << 0)
# define I915_MPEG_CLOCK_GATE_DISABLE (1 << 16)
# define I915_VLD_IP_PR_CLOCK_GATE_DISABLE (1 << 15)
# define I915_BY_CLOCK_GATE_DISABLE (1 << 0)
# define I965_RCZ_CLOCK_GATE_DISABLE (1 << 30)
-/** This bit must always be set on 965G/965GM */
+/* This bit must always be set on 965G/965GM */
# define I965_RCC_CLOCK_GATE_DISABLE (1 << 29)
# define I965_RCPB_CLOCK_GATE_DISABLE (1 << 28)
# define I965_DAP_CLOCK_GATE_DISABLE (1 << 27)
# define I965_ROC_CLOCK_GATE_DISABLE (1 << 26)
# define I965_GW_CLOCK_GATE_DISABLE (1 << 25)
# define I965_TD_CLOCK_GATE_DISABLE (1 << 24)
-/** This bit must always be set on 965G */
+/* This bit must always be set on 965G */
# define I965_ISC_CLOCK_GATE_DISABLE (1 << 23)
# define I965_IC_CLOCK_GATE_DISABLE (1 << 22)
# define I965_EU_CLOCK_GATE_DISABLE (1 << 21)
#define VF_UNIT_CLOCK_GATE_DISABLE (1 << 9)
#define GS_UNIT_CLOCK_GATE_DISABLE (1 << 7)
#define CL_UNIT_CLOCK_GATE_DISABLE (1 << 6)
+
+#define VDECCLK_GATE_D 0x620C /* g4x only */
+#define VCP_UNIT_CLOCK_GATE_DISABLE (1 << 4)
+
#define RAMCLK_GATE_D 0x6210 /* CRL only */
#define DEUC 0x6214 /* CRL only */
/* Memory controller frequency in MCHBAR for Haswell (possible SNB+) */
#define DCLK (MCHBAR_MIRROR_BASE_SNB + 0x5e04)
-/** 915-945 and GM965 MCH register controlling DRAM channel access */
+/* 915-945 and GM965 MCH register controlling DRAM channel access */
#define DCC 0x10200
#define DCC_ADDRESSING_MODE_SINGLE_CHANNEL (0 << 0)
#define DCC_ADDRESSING_MODE_DUAL_CHANNEL_ASYMMETRIC (1 << 0)
#define DCC_CHANNEL_XOR_DISABLE (1 << 10)
#define DCC_CHANNEL_XOR_BIT_17 (1 << 9)
-/** Pineview MCH register contains DDR3 setting */
+/* Pineview MCH register contains DDR3 setting */
#define CSHRDDR3CTL 0x101a8
#define CSHRDDR3CTL_DDR3 (1 << 2)
-/** 965 MCH register controlling DRAM channel configuration */
+/* 965 MCH register controlling DRAM channel configuration */
#define C0DRB3 0x10206
#define C1DRB3 0x10606
-/** snb MCH registers for reading the DRAM channel configuration */
+/* snb MCH registers for reading the DRAM channel configuration */
#define MAD_DIMM_C0 (MCHBAR_MIRROR_BASE_SNB + 0x5004)
#define MAD_DIMM_C1 (MCHBAR_MIRROR_BASE_SNB + 0x5008)
#define MAD_DIMM_C2 (MCHBAR_MIRROR_BASE_SNB + 0x500C)
#define MAD_DIMM_A_SIZE_SHIFT 0
#define MAD_DIMM_A_SIZE_MASK (0xff << MAD_DIMM_A_SIZE_SHIFT)
-/** snb MCH registers for priority tuning */
+/* snb MCH registers for priority tuning */
#define MCH_SSKPD (MCHBAR_MIRROR_BASE_SNB + 0x5d10)
#define MCH_SSKPD_WM0_MASK 0x3f
#define MCH_SSKPD_WM0_VAL 0xc
#define GEN3_SDVOC 0x61160
#define GEN4_HDMIB GEN3_SDVOB
#define GEN4_HDMIC GEN3_SDVOC
+#define CHV_HDMID 0x6116C
#define PCH_SDVOB 0xe1140
#define PCH_HDMIB PCH_SDVOB
#define PCH_HDMIC 0xe1150
#define SDVO_PIPE_B_SELECT (1 << 30)
#define SDVO_STALL_SELECT (1 << 29)
#define SDVO_INTERRUPT_ENABLE (1 << 26)
-/**
+/*
* 915G/GM SDVO pixel multiplier.
* Programmed value is multiplier - 1, up to 5x.
* \sa DPLL_MD_UDI_MULTIPLIER_MASK
/* TV port control */
#define TV_CTL 0x68000
-/** Enables the TV encoder */
+/* Enables the TV encoder */
# define TV_ENC_ENABLE (1 << 31)
-/** Sources the TV encoder input from pipe B instead of A. */
+/* Sources the TV encoder input from pipe B instead of A. */
# define TV_ENC_PIPEB_SELECT (1 << 30)
-/** Outputs composite video (DAC A only) */
+/* Outputs composite video (DAC A only) */
# define TV_ENC_OUTPUT_COMPOSITE (0 << 28)
-/** Outputs SVideo video (DAC B/C) */
+/* Outputs SVideo video (DAC B/C) */
# define TV_ENC_OUTPUT_SVIDEO (1 << 28)
-/** Outputs Component video (DAC A/B/C) */
+/* Outputs Component video (DAC A/B/C) */
# define TV_ENC_OUTPUT_COMPONENT (2 << 28)
-/** Outputs Composite and SVideo (DAC A/B/C) */
+/* Outputs Composite and SVideo (DAC A/B/C) */
# define TV_ENC_OUTPUT_SVIDEO_COMPOSITE (3 << 28)
# define TV_TRILEVEL_SYNC (1 << 21)
-/** Enables slow sync generation (945GM only) */
+/* Enables slow sync generation (945GM only) */
# define TV_SLOW_SYNC (1 << 20)
-/** Selects 4x oversampling for 480i and 576p */
+/* Selects 4x oversampling for 480i and 576p */
# define TV_OVERSAMPLE_4X (0 << 18)
-/** Selects 2x oversampling for 720p and 1080i */
+/* Selects 2x oversampling for 720p and 1080i */
# define TV_OVERSAMPLE_2X (1 << 18)
-/** Selects no oversampling for 1080p */
+/* Selects no oversampling for 1080p */
# define TV_OVERSAMPLE_NONE (2 << 18)
-/** Selects 8x oversampling */
+/* Selects 8x oversampling */
# define TV_OVERSAMPLE_8X (3 << 18)
-/** Selects progressive mode rather than interlaced */
+/* Selects progressive mode rather than interlaced */
# define TV_PROGRESSIVE (1 << 17)
-/** Sets the colorburst to PAL mode. Required for non-M PAL modes. */
+/* Sets the colorburst to PAL mode. Required for non-M PAL modes. */
# define TV_PAL_BURST (1 << 16)
-/** Field for setting delay of Y compared to C */
+/* Field for setting delay of Y compared to C */
# define TV_YC_SKEW_MASK (7 << 12)
-/** Enables a fix for 480p/576p standard definition modes on the 915GM only */
+/* Enables a fix for 480p/576p standard definition modes on the 915GM only */
# define TV_ENC_SDP_FIX (1 << 11)
-/**
+/*
* Enables a fix for the 915GM only.
*
* Not sure what it does.
*/
# define TV_ENC_C0_FIX (1 << 10)
-/** Bits that must be preserved by software */
+/* Bits that must be preserved by software */
# define TV_CTL_SAVE ((1 << 11) | (3 << 9) | (7 << 6) | 0xf)
# define TV_FUSE_STATE_MASK (3 << 4)
-/** Read-only state that reports all features enabled */
+/* Read-only state that reports all features enabled */
# define TV_FUSE_STATE_ENABLED (0 << 4)
-/** Read-only state that reports that Macrovision is disabled in hardware*/
+/* Read-only state that reports that Macrovision is disabled in hardware*/
# define TV_FUSE_STATE_NO_MACROVISION (1 << 4)
-/** Read-only state that reports that TV-out is disabled in hardware. */
+/* Read-only state that reports that TV-out is disabled in hardware. */
# define TV_FUSE_STATE_DISABLED (2 << 4)
-/** Normal operation */
+/* Normal operation */
# define TV_TEST_MODE_NORMAL (0 << 0)
-/** Encoder test pattern 1 - combo pattern */
+/* Encoder test pattern 1 - combo pattern */
# define TV_TEST_MODE_PATTERN_1 (1 << 0)
-/** Encoder test pattern 2 - full screen vertical 75% color bars */
+/* Encoder test pattern 2 - full screen vertical 75% color bars */
# define TV_TEST_MODE_PATTERN_2 (2 << 0)
-/** Encoder test pattern 3 - full screen horizontal 75% color bars */
+/* Encoder test pattern 3 - full screen horizontal 75% color bars */
# define TV_TEST_MODE_PATTERN_3 (3 << 0)
-/** Encoder test pattern 4 - random noise */
+/* Encoder test pattern 4 - random noise */
# define TV_TEST_MODE_PATTERN_4 (4 << 0)
-/** Encoder test pattern 5 - linear color ramps */
+/* Encoder test pattern 5 - linear color ramps */
# define TV_TEST_MODE_PATTERN_5 (5 << 0)
-/**
+/*
* This test mode forces the DACs to 50% of full output.
*
* This is used for load detection in combination with TVDAC_SENSE_MASK
#define TV_DAC 0x68004
# define TV_DAC_SAVE 0x00ffff00
-/**
+/*
* Reports that DAC state change logic has reported change (RO).
*
* This gets cleared when TV_DAC_STATE_EN is cleared
*/
# define TVDAC_STATE_CHG (1 << 31)
# define TVDAC_SENSE_MASK (7 << 28)
-/** Reports that DAC A voltage is above the detect threshold */
+/* Reports that DAC A voltage is above the detect threshold */
# define TVDAC_A_SENSE (1 << 30)
-/** Reports that DAC B voltage is above the detect threshold */
+/* Reports that DAC B voltage is above the detect threshold */
# define TVDAC_B_SENSE (1 << 29)
-/** Reports that DAC C voltage is above the detect threshold */
+/* Reports that DAC C voltage is above the detect threshold */
# define TVDAC_C_SENSE (1 << 28)
-/**
+/*
* Enables DAC state detection logic, for load-based TV detection.
*
* The PLL of the chosen pipe (in TV_CTL) must be running, and the encoder set
* to off, for load detection to work.
*/
# define TVDAC_STATE_CHG_EN (1 << 27)
-/** Sets the DAC A sense value to high */
+/* Sets the DAC A sense value to high */
# define TVDAC_A_SENSE_CTL (1 << 26)
-/** Sets the DAC B sense value to high */
+/* Sets the DAC B sense value to high */
# define TVDAC_B_SENSE_CTL (1 << 25)
-/** Sets the DAC C sense value to high */
+/* Sets the DAC C sense value to high */
# define TVDAC_C_SENSE_CTL (1 << 24)
-/** Overrides the ENC_ENABLE and DAC voltage levels */
+/* Overrides the ENC_ENABLE and DAC voltage levels */
# define DAC_CTL_OVERRIDE (1 << 7)
-/** Sets the slew rate. Must be preserved in software */
+/* Sets the slew rate. Must be preserved in software */
# define ENC_TVDAC_SLEW_FAST (1 << 6)
# define DAC_A_1_3_V (0 << 4)
# define DAC_A_1_1_V (1 << 4)
# define DAC_C_0_7_V (2 << 0)
# define DAC_C_MASK (3 << 0)
-/**
+/*
* CSC coefficients are stored in a floating point format with 9 bits of
* mantissa and 2 or 3 bits of exponent. The exponent is represented as 2**-n,
* where 2-bit exponents are unsigned n, and 3-bit exponents are signed n with
#define TV_CSC_Y2 0x68014
# define TV_BY_MASK 0x07ff0000
# define TV_BY_SHIFT 16
-/**
+/*
* Y attenuation for component video.
*
* Stored in 1.9 fixed point.
#define TV_CSC_U2 0x6801c
# define TV_BU_MASK 0x07ff0000
# define TV_BU_SHIFT 16
-/**
+/*
* U attenuation for component video.
*
* Stored in 1.9 fixed point.
#define TV_CSC_V2 0x68024
# define TV_BV_MASK 0x07ff0000
# define TV_BV_SHIFT 16
-/**
+/*
* V attenuation for component video.
*
* Stored in 1.9 fixed point.
# define TV_AV_SHIFT 0
#define TV_CLR_KNOBS 0x68028
-/** 2s-complement brightness adjustment */
+/* 2s-complement brightness adjustment */
# define TV_BRIGHTNESS_MASK 0xff000000
# define TV_BRIGHTNESS_SHIFT 24
-/** Contrast adjustment, as a 2.6 unsigned floating point number */
+/* Contrast adjustment, as a 2.6 unsigned floating point number */
# define TV_CONTRAST_MASK 0x00ff0000
# define TV_CONTRAST_SHIFT 16
-/** Saturation adjustment, as a 2.6 unsigned floating point number */
+/* Saturation adjustment, as a 2.6 unsigned floating point number */
# define TV_SATURATION_MASK 0x0000ff00
# define TV_SATURATION_SHIFT 8
-/** Hue adjustment, as an integer phase angle in degrees */
+/* Hue adjustment, as an integer phase angle in degrees */
# define TV_HUE_MASK 0x000000ff
# define TV_HUE_SHIFT 0
#define TV_CLR_LEVEL 0x6802c
-/** Controls the DAC level for black */
+/* Controls the DAC level for black */
# define TV_BLACK_LEVEL_MASK 0x01ff0000
# define TV_BLACK_LEVEL_SHIFT 16
-/** Controls the DAC level for blanking */
+/* Controls the DAC level for blanking */
# define TV_BLANK_LEVEL_MASK 0x000001ff
# define TV_BLANK_LEVEL_SHIFT 0
#define TV_H_CTL_1 0x68030
-/** Number of pixels in the hsync. */
+/* Number of pixels in the hsync. */
# define TV_HSYNC_END_MASK 0x1fff0000
# define TV_HSYNC_END_SHIFT 16
-/** Total number of pixels minus one in the line (display and blanking). */
+/* Total number of pixels minus one in the line (display and blanking). */
# define TV_HTOTAL_MASK 0x00001fff
# define TV_HTOTAL_SHIFT 0
#define TV_H_CTL_2 0x68034
-/** Enables the colorburst (needed for non-component color) */
+/* Enables the colorburst (needed for non-component color) */
# define TV_BURST_ENA (1 << 31)
-/** Offset of the colorburst from the start of hsync, in pixels minus one. */
+/* Offset of the colorburst from the start of hsync, in pixels minus one. */
# define TV_HBURST_START_SHIFT 16
# define TV_HBURST_START_MASK 0x1fff0000
-/** Length of the colorburst */
+/* Length of the colorburst */
# define TV_HBURST_LEN_SHIFT 0
# define TV_HBURST_LEN_MASK 0x0001fff
#define TV_H_CTL_3 0x68038
-/** End of hblank, measured in pixels minus one from start of hsync */
+/* End of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_END_SHIFT 16
# define TV_HBLANK_END_MASK 0x1fff0000
-/** Start of hblank, measured in pixels minus one from start of hsync */
+/* Start of hblank, measured in pixels minus one from start of hsync */
# define TV_HBLANK_START_SHIFT 0
# define TV_HBLANK_START_MASK 0x0001fff
#define TV_V_CTL_1 0x6803c
-/** XXX */
+/* XXX */
# define TV_NBR_END_SHIFT 16
# define TV_NBR_END_MASK 0x07ff0000
-/** XXX */
+/* XXX */
# define TV_VI_END_F1_SHIFT 8
# define TV_VI_END_F1_MASK 0x00003f00
-/** XXX */
+/* XXX */
# define TV_VI_END_F2_SHIFT 0
# define TV_VI_END_F2_MASK 0x0000003f
#define TV_V_CTL_2 0x68040
-/** Length of vsync, in half lines */
+/* Length of vsync, in half lines */
# define TV_VSYNC_LEN_MASK 0x07ff0000
# define TV_VSYNC_LEN_SHIFT 16
-/** Offset of the start of vsync in field 1, measured in one less than the
+/* Offset of the start of vsync in field 1, measured in one less than the
* number of half lines.
*/
# define TV_VSYNC_START_F1_MASK 0x00007f00
# define TV_VSYNC_START_F1_SHIFT 8
-/**
+/*
* Offset of the start of vsync in field 2, measured in one less than the
* number of half lines.
*/
# define TV_VSYNC_START_F2_SHIFT 0
#define TV_V_CTL_3 0x68044
-/** Enables generation of the equalization signal */
+/* Enables generation of the equalization signal */
# define TV_EQUAL_ENA (1 << 31)
-/** Length of vsync, in half lines */
+/* Length of vsync, in half lines */
# define TV_VEQ_LEN_MASK 0x007f0000
# define TV_VEQ_LEN_SHIFT 16
-/** Offset of the start of equalization in field 1, measured in one less than
+/* Offset of the start of equalization in field 1, measured in one less than
* the number of half lines.
*/
# define TV_VEQ_START_F1_MASK 0x0007f00
# define TV_VEQ_START_F1_SHIFT 8
-/**
+/*
* Offset of the start of equalization in field 2, measured in one less than
* the number of half lines.
*/
# define TV_VEQ_START_F2_SHIFT 0
#define TV_V_CTL_4 0x68048
-/**
+/*
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F1_MASK 0x003f0000
# define TV_VBURST_START_F1_SHIFT 16
-/**
+/*
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F1_SHIFT 0
#define TV_V_CTL_5 0x6804c
-/**
+/*
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F2_MASK 0x003f0000
# define TV_VBURST_START_F2_SHIFT 16
-/**
+/*
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F2_SHIFT 0
#define TV_V_CTL_6 0x68050
-/**
+/*
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F3_MASK 0x003f0000
# define TV_VBURST_START_F3_SHIFT 16
-/**
+/*
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F3_SHIFT 0
#define TV_V_CTL_7 0x68054
-/**
+/*
* Offset to start of vertical colorburst, measured in one less than the
* number of lines from vertical start.
*/
# define TV_VBURST_START_F4_MASK 0x003f0000
# define TV_VBURST_START_F4_SHIFT 16
-/**
+/*
* Offset to the end of vertical colorburst, measured in one less than the
* number of lines from the start of NBR.
*/
# define TV_VBURST_END_F4_SHIFT 0
#define TV_SC_CTL_1 0x68060
-/** Turns on the first subcarrier phase generation DDA */
+/* Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA1_EN (1 << 31)
-/** Turns on the first subcarrier phase generation DDA */
+/* Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA2_EN (1 << 30)
-/** Turns on the first subcarrier phase generation DDA */
+/* Turns on the first subcarrier phase generation DDA */
# define TV_SC_DDA3_EN (1 << 29)
-/** Sets the subcarrier DDA to reset frequency every other field */
+/* Sets the subcarrier DDA to reset frequency every other field */
# define TV_SC_RESET_EVERY_2 (0 << 24)
-/** Sets the subcarrier DDA to reset frequency every fourth field */
+/* Sets the subcarrier DDA to reset frequency every fourth field */
# define TV_SC_RESET_EVERY_4 (1 << 24)
-/** Sets the subcarrier DDA to reset frequency every eighth field */
+/* Sets the subcarrier DDA to reset frequency every eighth field */
# define TV_SC_RESET_EVERY_8 (2 << 24)
-/** Sets the subcarrier DDA to never reset the frequency */
+/* Sets the subcarrier DDA to never reset the frequency */
# define TV_SC_RESET_NEVER (3 << 24)
-/** Sets the peak amplitude of the colorburst.*/
+/* Sets the peak amplitude of the colorburst.*/
# define TV_BURST_LEVEL_MASK 0x00ff0000
# define TV_BURST_LEVEL_SHIFT 16
-/** Sets the increment of the first subcarrier phase generation DDA */
+/* Sets the increment of the first subcarrier phase generation DDA */
# define TV_SCDDA1_INC_MASK 0x00000fff
# define TV_SCDDA1_INC_SHIFT 0
#define TV_SC_CTL_2 0x68064
-/** Sets the rollover for the second subcarrier phase generation DDA */
+/* Sets the rollover for the second subcarrier phase generation DDA */
# define TV_SCDDA2_SIZE_MASK 0x7fff0000
# define TV_SCDDA2_SIZE_SHIFT 16
-/** Sets the increent of the second subcarrier phase generation DDA */
+/* Sets the increent of the second subcarrier phase generation DDA */
# define TV_SCDDA2_INC_MASK 0x00007fff
# define TV_SCDDA2_INC_SHIFT 0
#define TV_SC_CTL_3 0x68068
-/** Sets the rollover for the third subcarrier phase generation DDA */
+/* Sets the rollover for the third subcarrier phase generation DDA */
# define TV_SCDDA3_SIZE_MASK 0x7fff0000
# define TV_SCDDA3_SIZE_SHIFT 16
-/** Sets the increent of the third subcarrier phase generation DDA */
+/* Sets the increent of the third subcarrier phase generation DDA */
# define TV_SCDDA3_INC_MASK 0x00007fff
# define TV_SCDDA3_INC_SHIFT 0
#define TV_WIN_POS 0x68070
-/** X coordinate of the display from the start of horizontal active */
+/* X coordinate of the display from the start of horizontal active */
# define TV_XPOS_MASK 0x1fff0000
# define TV_XPOS_SHIFT 16
-/** Y coordinate of the display from the start of vertical active (NBR) */
+/* Y coordinate of the display from the start of vertical active (NBR) */
# define TV_YPOS_MASK 0x00000fff
# define TV_YPOS_SHIFT 0
#define TV_WIN_SIZE 0x68074
-/** Horizontal size of the display window, measured in pixels*/
+/* Horizontal size of the display window, measured in pixels*/
# define TV_XSIZE_MASK 0x1fff0000
# define TV_XSIZE_SHIFT 16
-/**
+/*
* Vertical size of the display window, measured in pixels.
*
* Must be even for interlaced modes.
# define TV_YSIZE_SHIFT 0
#define TV_FILTER_CTL_1 0x68080
-/**
+/*
* Enables automatic scaling calculation.
*
* If set, the rest of the registers are ignored, and the calculated values can
* be read back from the register.
*/
# define TV_AUTO_SCALE (1 << 31)
-/**
+/*
* Disables the vertical filter.
*
* This is required on modes more than 1024 pixels wide */
# define TV_V_FILTER_BYPASS (1 << 29)
-/** Enables adaptive vertical filtering */
+/* Enables adaptive vertical filtering */
# define TV_VADAPT (1 << 28)
# define TV_VADAPT_MODE_MASK (3 << 26)
-/** Selects the least adaptive vertical filtering mode */
+/* Selects the least adaptive vertical filtering mode */
# define TV_VADAPT_MODE_LEAST (0 << 26)
-/** Selects the moderately adaptive vertical filtering mode */
+/* Selects the moderately adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MODERATE (1 << 26)
-/** Selects the most adaptive vertical filtering mode */
+/* Selects the most adaptive vertical filtering mode */
# define TV_VADAPT_MODE_MOST (3 << 26)
-/**
+/*
* Sets the horizontal scaling factor.
*
* This should be the fractional part of the horizontal scaling factor divided
# define TV_HSCALE_FRAC_SHIFT 0
#define TV_FILTER_CTL_2 0x68084
-/**
+/*
* Sets the integer part of the 3.15 fixed-point vertical scaling factor.
*
* TV_VSCALE should be (src height - 1) / ((interlace * dest height) - 1)
*/
# define TV_VSCALE_INT_MASK 0x00038000
# define TV_VSCALE_INT_SHIFT 15
-/**
+/*
* Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
*
* \sa TV_VSCALE_INT_MASK
# define TV_VSCALE_FRAC_SHIFT 0
#define TV_FILTER_CTL_3 0x68088
-/**
+/*
* Sets the integer part of the 3.15 fixed-point vertical scaling factor.
*
* TV_VSCALE should be (src height - 1) / (1/4 * (dest height - 1))
*/
# define TV_VSCALE_IP_INT_MASK 0x00038000
# define TV_VSCALE_IP_INT_SHIFT 15
-/**
+/*
* Sets the fractional part of the 3.15 fixed-point vertical scaling factor.
*
* For progressive modes, TV_VSCALE_IP_INT should be set to zeroes.
#define TV_CC_CONTROL 0x68090
# define TV_CC_ENABLE (1 << 31)
-/**
+/*
* Specifies which field to send the CC data in.
*
* CC data is usually sent in field 0.
*/
# define TV_CC_FID_MASK (1 << 27)
# define TV_CC_FID_SHIFT 27
-/** Sets the horizontal position of the CC data. Usually 135. */
+/* Sets the horizontal position of the CC data. Usually 135. */
# define TV_CC_HOFF_MASK 0x03ff0000
# define TV_CC_HOFF_SHIFT 16
-/** Sets the vertical position of the CC data. Usually 21 */
+/* Sets the vertical position of the CC data. Usually 21 */
# define TV_CC_LINE_MASK 0x0000003f
# define TV_CC_LINE_SHIFT 0
#define TV_CC_DATA 0x68094
# define TV_CC_RDY (1 << 31)
-/** Second word of CC data to be transmitted. */
+/* Second word of CC data to be transmitted. */
# define TV_CC_DATA_2_MASK 0x007f0000
# define TV_CC_DATA_2_SHIFT 16
-/** First word of CC data to be transmitted. */
+/* First word of CC data to be transmitted. */
# define TV_CC_DATA_1_MASK 0x0000007f
# define TV_CC_DATA_1_SHIFT 0
#define DP_PLL_FREQ_160MHZ (1 << 16)
#define DP_PLL_FREQ_MASK (3 << 16)
-/** locked once port is enabled */
+/* locked once port is enabled */
#define DP_PORT_REVERSAL (1 << 15)
/* eDP */
#define DP_PLL_ENABLE (1 << 14)
-/** sends the clock on lane 15 of the PEG for debug */
+/* sends the clock on lane 15 of the PEG for debug */
#define DP_CLOCK_OUTPUT_ENABLE (1 << 13)
#define DP_SCRAMBLING_DISABLE (1 << 12)
#define DP_SCRAMBLING_DISABLE_IRONLAKE (1 << 7)
-/** limit RGB values to avoid confusing TVs */
+/* limit RGB values to avoid confusing TVs */
#define DP_COLOR_RANGE_16_235 (1 << 8)
-/** Turn on the audio link */
+/* Turn on the audio link */
#define DP_AUDIO_OUTPUT_ENABLE (1 << 6)
-/** vs and hs sync polarity */
+/* vs and hs sync polarity */
#define DP_SYNC_VS_HIGH (1 << 4)
#define DP_SYNC_HS_HIGH (1 << 3)
-/** A fantasy */
+/* A fantasy */
#define DP_DETECTED (1 << 2)
-/** The aux channel provides a way to talk to the
+/* The aux channel provides a way to talk to the
* signal sink for DDC etc. Max packet size supported
* is 20 bytes in each direction, hence the 5 fixed
* data registers
#define _PIPEA_FRMCOUNT_GM45 0x70040
#define _PIPEA_FLIPCOUNT_GM45 0x70044
#define PIPE_FRMCOUNT_GM45(pipe) _PIPE2(pipe, _PIPEA_FRMCOUNT_GM45)
+#define PIPE_FLIPCOUNT_GM45(pipe) _PIPE2(pipe, _PIPEA_FLIPCOUNT_GM45)
/* Cursor A & B regs */
-#define _CURACNTR (dev_priv->info.display_mmio_offset + 0x70080)
+#define _CURACNTR 0x70080
/* Old style CUR*CNTR flags (desktop 8xx) */
#define CURSOR_ENABLE 0x80000000
#define CURSOR_GAMMA_ENABLE 0x40000000
#define MCURSOR_PIPE_B (1 << 28)
#define MCURSOR_GAMMA_ENABLE (1 << 26)
#define CURSOR_TRICKLE_FEED_DISABLE (1 << 14)
-#define _CURABASE (dev_priv->info.display_mmio_offset + 0x70084)
-#define _CURAPOS (dev_priv->info.display_mmio_offset + 0x70088)
+#define _CURABASE 0x70084
+#define _CURAPOS 0x70088
#define CURSOR_POS_MASK 0x007FF
#define CURSOR_POS_SIGN 0x8000
#define CURSOR_X_SHIFT 0
#define CURSOR_Y_SHIFT 16
#define CURSIZE 0x700a0
-#define _CURBCNTR (dev_priv->info.display_mmio_offset + 0x700c0)
-#define _CURBBASE (dev_priv->info.display_mmio_offset + 0x700c4)
-#define _CURBPOS (dev_priv->info.display_mmio_offset + 0x700c8)
+#define _CURBCNTR 0x700c0
+#define _CURBBASE 0x700c4
+#define _CURBPOS 0x700c8
#define _CURBCNTR_IVB 0x71080
#define _CURBBASE_IVB 0x71084
#define _CURBPOS_IVB 0x71088
-#define CURCNTR(pipe) _PIPE(pipe, _CURACNTR, _CURBCNTR)
-#define CURBASE(pipe) _PIPE(pipe, _CURABASE, _CURBBASE)
-#define CURPOS(pipe) _PIPE(pipe, _CURAPOS, _CURBPOS)
+#define _CURSOR2(pipe, reg) (dev_priv->info.cursor_offsets[(pipe)] - \
+ dev_priv->info.cursor_offsets[PIPE_A] + (reg) + \
+ dev_priv->info.display_mmio_offset)
+
+#define CURCNTR(pipe) _CURSOR2(pipe, _CURACNTR)
+#define CURBASE(pipe) _CURSOR2(pipe, _CURABASE)
+#define CURPOS(pipe) _CURSOR2(pipe, _CURAPOS)
-#define CURCNTR_IVB(pipe) _PIPE(pipe, _CURACNTR, _CURBCNTR_IVB)
-#define CURBASE_IVB(pipe) _PIPE(pipe, _CURABASE, _CURBBASE_IVB)
-#define CURPOS_IVB(pipe) _PIPE(pipe, _CURAPOS, _CURBPOS_IVB)
+#define CURSOR_A_OFFSET 0x70080
+#define CURSOR_B_OFFSET 0x700c0
+#define CHV_CURSOR_C_OFFSET 0x700e0
+#define IVB_CURSOR_B_OFFSET 0x71080
+#define IVB_CURSOR_C_OFFSET 0x72080
/* Display A control */
#define _DSPACNTR 0x70180
#define _PCH_TRANSA_LINK_M2 0xe0048
#define _PCH_TRANSA_LINK_N2 0xe004c
-/* Per-transcoder DIP controls */
-
+/* Per-transcoder DIP controls (PCH) */
#define _VIDEO_DIP_CTL_A 0xe0200
#define _VIDEO_DIP_DATA_A 0xe0208
#define _VIDEO_DIP_GCP_A 0xe0210
#define TVIDEO_DIP_DATA(pipe) _PIPE(pipe, _VIDEO_DIP_DATA_A, _VIDEO_DIP_DATA_B)
#define TVIDEO_DIP_GCP(pipe) _PIPE(pipe, _VIDEO_DIP_GCP_A, _VIDEO_DIP_GCP_B)
+/* Per-transcoder DIP controls (VLV) */
#define VLV_VIDEO_DIP_CTL_A (VLV_DISPLAY_BASE + 0x60200)
#define VLV_VIDEO_DIP_DATA_A (VLV_DISPLAY_BASE + 0x60208)
#define VLV_VIDEO_DIP_GDCP_PAYLOAD_A (VLV_DISPLAY_BASE + 0x60210)
#define VLV_VIDEO_DIP_DATA_B (VLV_DISPLAY_BASE + 0x61174)
#define VLV_VIDEO_DIP_GDCP_PAYLOAD_B (VLV_DISPLAY_BASE + 0x61178)
+#define CHV_VIDEO_DIP_CTL_C (VLV_DISPLAY_BASE + 0x611f0)
+#define CHV_VIDEO_DIP_DATA_C (VLV_DISPLAY_BASE + 0x611f4)
+#define CHV_VIDEO_DIP_GDCP_PAYLOAD_C (VLV_DISPLAY_BASE + 0x611f8)
+
#define VLV_TVIDEO_DIP_CTL(pipe) \
- _PIPE(pipe, VLV_VIDEO_DIP_CTL_A, VLV_VIDEO_DIP_CTL_B)
+ _PIPE3((pipe), VLV_VIDEO_DIP_CTL_A, \
+ VLV_VIDEO_DIP_CTL_B, CHV_VIDEO_DIP_CTL_C)
#define VLV_TVIDEO_DIP_DATA(pipe) \
- _PIPE(pipe, VLV_VIDEO_DIP_DATA_A, VLV_VIDEO_DIP_DATA_B)
+ _PIPE3((pipe), VLV_VIDEO_DIP_DATA_A, \
+ VLV_VIDEO_DIP_DATA_B, CHV_VIDEO_DIP_DATA_C)
#define VLV_TVIDEO_DIP_GCP(pipe) \
- _PIPE(pipe, VLV_VIDEO_DIP_GDCP_PAYLOAD_A, VLV_VIDEO_DIP_GDCP_PAYLOAD_B)
+ _PIPE3((pipe), VLV_VIDEO_DIP_GDCP_PAYLOAD_A, \
+ VLV_VIDEO_DIP_GDCP_PAYLOAD_B, CHV_VIDEO_DIP_GDCP_PAYLOAD_C)
/* Haswell DIP controls */
#define HSW_VIDEO_DIP_CTL_A 0x60200
#define PORT_TRANS_SEL_CPT(pipe) ((pipe) << 29)
#define PORT_TO_PIPE(val) (((val) & (1<<30)) >> 30)
#define PORT_TO_PIPE_CPT(val) (((val) & PORT_TRANS_SEL_MASK) >> 29)
+#define SDVO_PORT_TO_PIPE_CHV(val) (((val) & (3<<24)) >> 24)
+#define DP_PORT_TO_PIPE_CHV(val) (((val) & (3<<16)) >> 16)
#define TRANS_DP_CTL_A 0xe0300
#define TRANS_DP_CTL_B 0xe1300
#define HSW_EDRAM_PRESENT 0x120010
#define GEN6_UCGCTL1 0x9400
+# define GEN6_EU_TCUNIT_CLOCK_GATE_DISABLE (1 << 16)
# define GEN6_BLBUNIT_CLOCK_GATE_DISABLE (1 << 5)
# define GEN6_CSUNIT_CLOCK_GATE_DISABLE (1 << 7)
/* For UMS only (deprecated): */
#define _PALETTE_A (dev_priv->info.display_mmio_offset + 0xa000)
#define _PALETTE_B (dev_priv->info.display_mmio_offset + 0xa800)
-#define _DPLL_A (dev_priv->info.display_mmio_offset + 0x6014)
-#define _DPLL_B (dev_priv->info.display_mmio_offset + 0x6018)
-#define _DPLL_A_MD (dev_priv->info.display_mmio_offset + 0x601c)
-#define _DPLL_B_MD (dev_priv->info.display_mmio_offset + 0x6020)
#endif /* _I915_REG_H_ */