#include "libata.h"
+/**
+ * ata_irq_on - Enable interrupts on a port.
+ * @ap: Port on which interrupts are enabled.
+ *
+ * Enable interrupts on a legacy IDE device using MMIO or PIO,
+ * wait for idle, clear any pending interrupts.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+u8 ata_irq_on(struct ata_port *ap)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ u8 tmp;
+
+ ap->ctl &= ~ATA_NIEN;
+ ap->last_ctl = ap->ctl;
+
+ if (ap->flags & ATA_FLAG_MMIO)
+ writeb(ap->ctl, (void __iomem *) ioaddr->ctl_addr);
+ else
+ outb(ap->ctl, ioaddr->ctl_addr);
+ tmp = ata_wait_idle(ap);
+
+ ap->ops->irq_clear(ap);
+
+ return tmp;
+}
+
/**
* ata_tf_load_pio - send taskfile registers to host controller
* @ap: Port to which output is sent
writeb(ap->ctl, (void __iomem *)ioaddr->ctl_addr);
else
outb(ap->ctl, ioaddr->ctl_addr);
+
+ /* Under certain circumstances, some controllers raise IRQ on
+ * ATA_NIEN manipulation. Also, many controllers fail to mask
+ * previously pending IRQ on ATA_NIEN assertion. Clear it.
+ */
+ ata_chk_status(ap);
+
+ ap->ops->irq_clear(ap);
}
/**
ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
ata_postreset_fn_t postreset)
{
- struct ata_eh_context *ehc = &ap->eh_context;
struct ata_queued_cmd *qc;
unsigned long flags;
int thaw = 0;
qc->tf.protocol == ATA_PROT_ATAPI_DMA)) {
u8 host_stat;
- host_stat = ata_bmdma_status(ap);
-
- ata_ehi_push_desc(&ehc->i, "BMDMA stat 0x%x", host_stat);
+ host_stat = ap->ops->bmdma_status(ap);
/* BMDMA controllers indicate host bus error by
* setting DMA_ERR bit and timing out. As it wasn't
probe_ent->irq = pdev->irq;
probe_ent->irq_flags = IRQF_SHARED;
- probe_ent->private_data = port[0]->private_data;
if (ports & ATA_PORT_PRIMARY) {
probe_ent->port[p].cmd_addr = pci_resource_start(pdev, 0);
return NULL;
probe_ent->n_ports = 2;
- probe_ent->private_data = port[0]->private_data;
+ probe_ent->irq_flags = IRQF_SHARED;
if (port_mask & ATA_PORT_PRIMARY) {
probe_ent->irq = ATA_PRIMARY_IRQ;
probe_ent->_host_flags |= ATA_HOST_SIMPLEX;
}
ata_std_ports(&probe_ent->port[1]);
+
+ /* FIXME: could be pointing to stack area; must copy */
probe_ent->pinfo2 = port[1];
} else
probe_ent->dummy_port_mask |= ATA_PORT_SECONDARY;
{
struct ata_probe_ent *probe_ent = NULL;
struct ata_port_info *port[2];
- u8 tmp8, mask;
+ u8 mask;
unsigned int legacy_mode = 0;
int disable_dev_on_err = 1;
int rc;
DPRINTK("ENTER\n");
+ BUG_ON(n_ports < 1 || n_ports > 2);
+
port[0] = port_info[0];
if (n_ports > 1)
port[1] = port_info[1];
else
port[1] = port[0];
- if ((port[0]->flags & ATA_FLAG_NO_LEGACY) == 0
- && (pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
- /* TODO: What if one channel is in native mode ... */
- pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
- mask = (1 << 2) | (1 << 0);
- if ((tmp8 & mask) != mask)
- legacy_mode = (1 << 3);
- }
-
- /* FIXME... */
- if ((!legacy_mode) && (n_ports > 2)) {
- printk(KERN_ERR "ata: BUG: native mode, n_ports > 2\n");
- n_ports = 2;
- /* For now */
- }
-
/* FIXME: Really for ATA it isn't safe because the device may be
multi-purpose and we want to leave it alone if it was already
enabled. Secondly for shared use as Arjan says we want refcounting
if (rc)
return rc;
+ if ((pdev->class >> 8) == PCI_CLASS_STORAGE_IDE) {
+ u8 tmp8;
+
+ /* TODO: What if one channel is in native mode ... */
+ pci_read_config_byte(pdev, PCI_CLASS_PROG, &tmp8);
+ mask = (1 << 2) | (1 << 0);
+ if ((tmp8 & mask) != mask)
+ legacy_mode = (1 << 3);
+#if defined(CONFIG_NO_ATA_LEGACY)
+ /* Some platforms with PCI limits cannot address compat
+ port space. In that case we punt if their firmware has
+ left a device in compatibility mode */
+ if (legacy_mode) {
+ printk(KERN_ERR "ata: Compatibility mode ATA is not supported on this platform, skipping.\n");
+ return -EOPNOTSUPP;
+ }
+#endif
+ }
+
rc = pci_request_regions(pdev, DRV_NAME);
if (rc) {
disable_dev_on_err = 0;
goto err_out_regions;
}
- /* FIXME: If we get no DMA mask we should fall back to PIO */
+ /* TODO: If we get no DMA mask we should fall back to PIO */
rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
if (rc)
goto err_out_regions;
pci_set_master(pdev);
- /* FIXME: check ata_device_add return */
- ata_device_add(probe_ent);
+ if (!ata_device_add(probe_ent)) {
+ rc = -ENODEV;
+ goto err_out_ent;
+ }
kfree(probe_ent);
return 0;
+err_out_ent:
+ kfree(probe_ent);
err_out_regions:
if (legacy_mode & ATA_PORT_PRIMARY)
release_region(ATA_PRIMARY_CMD, 8);