#include <sysdev/fsl_soc.h>
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-static void cpm2_dpinit(void);
-#endif
-
cpm_cpm2_t __iomem *cpmp; /* Pointer to comm processor space */
/* We allocate this here because it is used almost exclusively for
/* Reclaim the DP memory for our use.
*/
-#ifdef CONFIG_PPC_CPM_NEW_BINDING
cpm_muram_init();
-#else
- cpm2_dpinit();
-#endif
/* Tell everyone where the comm processor resides.
*/
cpmp = &cpm2_immr->im_cpm;
+
+#ifndef CONFIG_PPC_EARLY_DEBUG_CPM
+ /* Reset the CPM.
+ */
+ cpm_command(CPM_CR_RST, 0);
+#endif
}
static DEFINE_SPINLOCK(cmd_lock);
* Baud rate clocks are zero-based in the driver code (as that maps
* to port numbers). Documentation uses 1-based numbering.
*/
-#define BRG_INT_CLK (get_brgfreq())
-#define BRG_UART_CLK (BRG_INT_CLK/16)
-
-/* This function is used by UARTS, or anything else that uses a 16x
- * oversampled clock.
- */
-void
-cpm_setbrg(uint brg, uint rate)
+void __cpm2_setbrg(uint brg, uint rate, uint clk, int div16, int src)
{
u32 __iomem *bp;
+ u32 val;
/* This is good enough to get SMCs running.....
*/
brg -= 4;
}
bp += brg;
- out_be32(bp, (((BRG_UART_CLK / rate) - 1) << 1) | CPM_BRG_EN);
-
- cpm2_unmap(bp);
-}
-
-/* This function is used to set high speed synchronous baud rate
- * clocks.
- */
-void
-cpm2_fastbrg(uint brg, uint rate, int div16)
-{
- u32 __iomem *bp;
- u32 val;
-
- if (brg < 4) {
- bp = cpm2_map_size(im_brgc1, 16);
- } else {
- bp = cpm2_map_size(im_brgc5, 16);
- brg -= 4;
- }
- bp += brg;
- val = ((BRG_INT_CLK / rate) << 1) | CPM_BRG_EN;
+ val = (((clk / rate) - 1) << 1) | CPM_BRG_EN | src;
if (div16)
val |= CPM_BRG_DIV16;
out_be32(bp, val);
cpm2_unmap(bp);
}
+EXPORT_SYMBOL(__cpm2_setbrg);
int cpm2_clk_setup(enum cpm_clk_target target, int clock, int mode)
{
case CPM_CLK_SCC1:
reg = &im_cpmux->cmx_scr;
shift = 24;
+ break;
case CPM_CLK_SCC2:
reg = &im_cpmux->cmx_scr;
shift = 16;
return ret;
}
-#ifndef CONFIG_PPC_CPM_NEW_BINDING
-/*
- * dpalloc / dpfree bits.
- */
-static spinlock_t cpm_dpmem_lock;
-/* 16 blocks should be enough to satisfy all requests
- * until the memory subsystem goes up... */
-static rh_block_t cpm_boot_dpmem_rh_block[16];
-static rh_info_t cpm_dpmem_info;
-static u8 __iomem *im_dprambase;
-
-static void cpm2_dpinit(void)
-{
- spin_lock_init(&cpm_dpmem_lock);
-
- /* initialize the info header */
- rh_init(&cpm_dpmem_info, 1,
- sizeof(cpm_boot_dpmem_rh_block) /
- sizeof(cpm_boot_dpmem_rh_block[0]),
- cpm_boot_dpmem_rh_block);
-
- im_dprambase = cpm2_immr;
-
- /* Attach the usable dpmem area */
- /* XXX: This is actually crap. CPM_DATAONLY_BASE and
- * CPM_DATAONLY_SIZE is only a subset of the available dpram. It
- * varies with the processor and the microcode patches activated.
- * But the following should be at least safe.
- */
- rh_attach_region(&cpm_dpmem_info, CPM_DATAONLY_BASE, CPM_DATAONLY_SIZE);
-}
-
-/* This function returns an index into the DPRAM area.
- */
-unsigned long cpm_dpalloc(uint size, uint align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- cpm_dpmem_info.alignment = align;
- start = rh_alloc(&cpm_dpmem_info, size, "commproc");
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return (uint)start;
-}
-EXPORT_SYMBOL(cpm_dpalloc);
-
-int cpm_dpfree(unsigned long offset)
-{
- int ret;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- ret = rh_free(&cpm_dpmem_info, offset);
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return ret;
-}
-EXPORT_SYMBOL(cpm_dpfree);
-
-/* not sure if this is ever needed */
-unsigned long cpm_dpalloc_fixed(unsigned long offset, uint size, uint align)
-{
- unsigned long start;
- unsigned long flags;
-
- spin_lock_irqsave(&cpm_dpmem_lock, flags);
- cpm_dpmem_info.alignment = align;
- start = rh_alloc_fixed(&cpm_dpmem_info, offset, size, "commproc");
- spin_unlock_irqrestore(&cpm_dpmem_lock, flags);
-
- return start;
-}
-EXPORT_SYMBOL(cpm_dpalloc_fixed);
-
-void cpm_dpdump(void)
-{
- rh_dump(&cpm_dpmem_info);
-}
-EXPORT_SYMBOL(cpm_dpdump);
-
-void *cpm_dpram_addr(unsigned long offset)
-{
- return (void *)(im_dprambase + offset);
-}
-EXPORT_SYMBOL(cpm_dpram_addr);
-#endif /* !CONFIG_PPC_CPM_NEW_BINDING */
-
struct cpm2_ioports {
u32 dir, par, sor, odr, dat;
u32 res[3];
else
clrbits32(&iop[port].odr, pin);
}
+
+static int cpm_init_par_io(void)
+{
+ struct device_node *np;
+
+ for_each_compatible_node(np, NULL, "fsl,cpm2-pario-bank")
+ cpm2_gpiochip_add32(np);
+ return 0;
+}
+arch_initcall(cpm_init_par_io);
+