* VIA have currently 3 different versions of Longhaul.
* Version 1 (Longhaul) uses the BCR2 MSR at 0x1147.
* It is present only in Samuel 1 (C5A), Samuel 2 (C5B) stepping 0.
- * Version 2 of longhaul is the same as v1, but adds voltage scaling.
- * Present in Samuel 2 (steppings 1-7 only) (C5B), and Ezra (C5C)
- * voltage scaling support has currently been disabled in this driver
- * until we have code that gets it right.
+ * Version 2 of longhaul is backward compatible with v1, but adds
+ * LONGHAUL MSR for purpose of both frequency and voltage scaling.
+ * Present in Samuel 2 (steppings 1-7 only) (C5B), and Ezra (C5C).
* Version 3 of longhaul got renamed to Powersaver and redesigned
- * to use the POWERSAVER MSR at 0x110a.
+ * to use only the POWERSAVER MSR at 0x110a.
* It is present in Ezra-T (C5M), Nehemiah (C5X) and above.
* It's pretty much the same feature wise to longhaul v2, though
* there is provision for scaling FSB too, but this doesn't work
static unsigned int numscales=16;
static unsigned int fsb;
-static struct mV_pos *vrm_mV_table;
-static unsigned char *mV_vrm_table;
+static const struct mV_pos *vrm_mV_table;
+static const unsigned char *mV_vrm_table;
struct f_msr {
- unsigned char vrm;
+ u8 vrm;
+ u8 pos;
};
static struct f_msr f_msr_table[32];
static struct acpi_processor *pr = NULL;
static struct acpi_processor_cx *cx = NULL;
static u8 longhaul_flags;
+static u8 longhaul_pos;
/* Module parameters */
static int scale_voltage;
static void do_powersaver(int cx_address, unsigned int clock_ratio_index)
{
union msr_longhaul longhaul;
+ u8 dest_pos;
u32 t;
+ dest_pos = f_msr_table[clock_ratio_index].pos;
+
rdmsrl(MSR_VIA_LONGHAUL, longhaul.val);
+ /* Setup new frequency */
longhaul.bits.RevisionKey = longhaul.bits.RevisionID;
longhaul.bits.SoftBusRatio = clock_ratio_index & 0xf;
longhaul.bits.SoftBusRatio4 = (clock_ratio_index & 0x10) >> 4;
- longhaul.bits.EnableSoftBusRatio = 1;
-
- if (can_scale_voltage) {
+ /* Setup new voltage */
+ if (can_scale_voltage)
longhaul.bits.SoftVID = f_msr_table[clock_ratio_index].vrm;
+ /* Sync to timer tick */
+ safe_halt();
+ /* Raise voltage if necessary */
+ if (can_scale_voltage && longhaul_pos < dest_pos) {
longhaul.bits.EnableSoftVID = 1;
+ wrmsrl(MSR_VIA_LONGHAUL, longhaul.val);
+ /* Change voltage */
+ if (!cx_address) {
+ ACPI_FLUSH_CPU_CACHE();
+ halt();
+ } else {
+ ACPI_FLUSH_CPU_CACHE();
+ /* Invoke C3 */
+ inb(cx_address);
+ /* Dummy op - must do something useless after P_LVL3
+ * read */
+ t = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ }
+ longhaul.bits.EnableSoftVID = 0;
+ wrmsrl(MSR_VIA_LONGHAUL, longhaul.val);
+ longhaul_pos = dest_pos;
}
- /* Sync to timer tick */
- safe_halt();
/* Change frequency on next halt or sleep */
+ longhaul.bits.EnableSoftBusRatio = 1;
wrmsrl(MSR_VIA_LONGHAUL, longhaul.val);
if (!cx_address) {
ACPI_FLUSH_CPU_CACHE();
- /* Invoke C1 */
halt();
} else {
ACPI_FLUSH_CPU_CACHE();
/* Invoke C3 */
inb(cx_address);
/* Dummy op - must do something useless after P_LVL3 read */
- t = inl(acpi_fadt.xpm_tmr_blk.address);
+ t = inl(acpi_gbl_FADT.xpm_timer_block.address);
}
/* Disable bus ratio bit */
- local_irq_disable();
- longhaul.bits.RevisionKey = longhaul.bits.RevisionID;
longhaul.bits.EnableSoftBusRatio = 0;
- longhaul.bits.EnableSoftBSEL = 0;
- longhaul.bits.EnableSoftVID = 0;
wrmsrl(MSR_VIA_LONGHAUL, longhaul.val);
+
+ /* Reduce voltage if necessary */
+ if (can_scale_voltage && longhaul_pos > dest_pos) {
+ longhaul.bits.EnableSoftVID = 1;
+ wrmsrl(MSR_VIA_LONGHAUL, longhaul.val);
+ /* Change voltage */
+ if (!cx_address) {
+ ACPI_FLUSH_CPU_CACHE();
+ halt();
+ } else {
+ ACPI_FLUSH_CPU_CACHE();
+ /* Invoke C3 */
+ inb(cx_address);
+ /* Dummy op - must do something useless after P_LVL3
+ * read */
+ t = inl(acpi_gbl_FADT.xpm_timer_block.address);
+ }
+ longhaul.bits.EnableSoftVID = 0;
+ wrmsrl(MSR_VIA_LONGHAUL, longhaul.val);
+ longhaul_pos = dest_pos;
+ }
}
/**
outb(3, 0x22);
} else if ((pr != NULL) && pr->flags.bm_control) {
/* Disable bus master arbitration */
- acpi_set_register(ACPI_BITREG_ARB_DISABLE, 1,
- ACPI_MTX_DO_NOT_LOCK);
+ acpi_set_register(ACPI_BITREG_ARB_DISABLE, 1);
}
switch (longhaul_version) {
/*
* Longhaul v1. (Samuel[C5A] and Samuel2 stepping 0[C5B])
* Software controlled multipliers only.
- *
- * *NB* Until we get voltage scaling working v1 & v2 are the same code.
- * Longhaul v2 appears in Samuel2 Steppings 1->7 [C5b] and Ezra [C5C]
*/
case TYPE_LONGHAUL_V1:
- case TYPE_LONGHAUL_V2:
do_longhaul1(clock_ratio_index);
break;
/*
+ * Longhaul v2 appears in Samuel2 Steppings 1->7 [C5B] and Ezra [C5C]
+ *
* Longhaul v3 (aka Powersaver). (Ezra-T [C5M] & Nehemiah [C5N])
- * We can scale voltage with this too, but that's currently
- * disabled until we come up with a decent 'match freq to voltage'
- * algorithm.
- * When we add voltage scaling, we will also need to do the
- * voltage/freq setting in order depending on the direction
- * of scaling (like we do in powernow-k7.c)
* Nehemiah can do FSB scaling too, but this has never been proven
* to work in practice.
*/
+ case TYPE_LONGHAUL_V2:
case TYPE_POWERSAVER:
if (longhaul_flags & USE_ACPI_C3) {
/* Don't allow wakeup */
- acpi_set_register(ACPI_BITREG_BUS_MASTER_RLD, 0,
- ACPI_MTX_DO_NOT_LOCK);
+ acpi_set_register(ACPI_BITREG_BUS_MASTER_RLD, 0);
do_powersaver(cx->address, clock_ratio_index);
} else {
do_powersaver(0, clock_ratio_index);
outb(0, 0x22);
} else if ((pr != NULL) && pr->flags.bm_control) {
/* Enable bus master arbitration */
- acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0,
- ACPI_MTX_DO_NOT_LOCK);
+ acpi_set_register(ACPI_BITREG_ARB_DISABLE, 0);
}
outb(pic2_mask,0xA1); /* restore mask */
outb(pic1_mask,0x21);
local_irq_restore(flags);
preempt_enable();
+ freqs.new = calc_speed(longhaul_get_cpu_mult());
cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
}
highest_speed = calc_speed(maxmult);
lowest_speed = calc_speed(minmult);
dprintk ("FSB:%dMHz Lowest speed: %s Highest speed:%s\n", fsb,
- print_speed(lowest_speed/1000),
+ print_speed(lowest_speed/1000),
print_speed(highest_speed/1000));
if (lowest_speed == highest_speed) {
union msr_longhaul longhaul;
struct mV_pos minvid, maxvid;
unsigned int j, speed, pos, kHz_step, numvscales;
+ int min_vid_speed;
rdmsrl(MSR_VIA_LONGHAUL, longhaul.val);
if (!(longhaul.bits.RevisionID & 1)) {
mV_vrm_table = &mV_vrm85[0];
} else {
printk (KERN_INFO PFX "Mobile VRM\n");
+ if (cpu_model < CPU_NEHEMIAH)
+ return;
vrm_mV_table = &mobilevrm_mV[0];
mV_vrm_table = &mV_mobilevrm[0];
}
minvid = vrm_mV_table[longhaul.bits.MinimumVID];
maxvid = vrm_mV_table[longhaul.bits.MaximumVID];
- numvscales = maxvid.pos - minvid.pos + 1;
- kHz_step = (highest_speed - lowest_speed) / numvscales;
if (minvid.mV == 0 || maxvid.mV == 0 || minvid.mV > maxvid.mV) {
printk (KERN_INFO PFX "Bogus values Min:%d.%03d Max:%d.%03d. "
return;
}
- printk(KERN_INFO PFX "Max VID=%d.%03d Min VID=%d.%03d, %d possible voltage scales\n",
+ /* How many voltage steps */
+ numvscales = maxvid.pos - minvid.pos + 1;
+ printk(KERN_INFO PFX
+ "Max VID=%d.%03d "
+ "Min VID=%d.%03d, "
+ "%d possible voltage scales\n",
maxvid.mV/1000, maxvid.mV%1000,
minvid.mV/1000, minvid.mV%1000,
numvscales);
-
+
+ /* Calculate max frequency at min voltage */
+ j = longhaul.bits.MinMHzBR;
+ if (longhaul.bits.MinMHzBR4)
+ j += 16;
+ min_vid_speed = eblcr_table[j];
+ if (min_vid_speed == -1)
+ return;
+ switch (longhaul.bits.MinMHzFSB) {
+ case 0:
+ min_vid_speed *= 13333;
+ break;
+ case 1:
+ min_vid_speed *= 10000;
+ break;
+ case 3:
+ min_vid_speed *= 6666;
+ break;
+ default:
+ return;
+ break;
+ }
+ if (min_vid_speed >= highest_speed)
+ return;
+ /* Calculate kHz for one voltage step */
+ kHz_step = (highest_speed - min_vid_speed) / numvscales;
+
+
j = 0;
while (longhaul_table[j].frequency != CPUFREQ_TABLE_END) {
speed = longhaul_table[j].frequency;
- pos = (speed - lowest_speed) / kHz_step + minvid.pos;
+ if (speed > min_vid_speed)
+ pos = (speed - min_vid_speed) / kHz_step + minvid.pos;
+ else
+ pos = minvid.pos;
f_msr_table[longhaul_table[j].index].vrm = mV_vrm_table[pos];
+ f_msr_table[longhaul_table[j].index].pos = pos;
j++;
}
+ longhaul_pos = maxvid.pos;
can_scale_voltage = 1;
+ printk(KERN_INFO PFX "Voltage scaling enabled. "
+ "Use of \"conservative\" governor is highly recommended.\n");
}
struct cpuinfo_x86 *c = cpu_data;
char *cpuname=NULL;
int ret;
+ u32 lo, hi;
int vt8235_present;
/* Check what we have on this motherboard */
break;
case 7:
- longhaul_version = TYPE_LONGHAUL_V1;
switch (c->x86_mask) {
case 0:
+ longhaul_version = TYPE_LONGHAUL_V1;
cpu_model = CPU_SAMUEL2;
cpuname = "C3 'Samuel 2' [C5B]";
- /* Note, this is not a typo, early Samuel2's had Samuel1 ratios. */
- memcpy (clock_ratio, samuel1_clock_ratio, sizeof(samuel1_clock_ratio));
- memcpy (eblcr_table, samuel2_eblcr, sizeof(samuel2_eblcr));
+ /* Note, this is not a typo, early Samuel2's had
+ * Samuel1 ratios. */
+ memcpy(clock_ratio, samuel1_clock_ratio,
+ sizeof(samuel1_clock_ratio));
+ memcpy(eblcr_table, samuel2_eblcr,
+ sizeof(samuel2_eblcr));
break;
case 1 ... 15:
+ longhaul_version = TYPE_LONGHAUL_V2;
if (c->x86_mask < 8) {
cpu_model = CPU_SAMUEL2;
cpuname = "C3 'Samuel 2' [C5B]";
cpu_model = CPU_EZRA;
cpuname = "C3 'Ezra' [C5C]";
}
- memcpy (clock_ratio, ezra_clock_ratio, sizeof(ezra_clock_ratio));
- memcpy (eblcr_table, ezra_eblcr, sizeof(ezra_eblcr));
+ memcpy(clock_ratio, ezra_clock_ratio,
+ sizeof(ezra_clock_ratio));
+ memcpy(eblcr_table, ezra_eblcr,
+ sizeof(ezra_eblcr));
break;
}
break;
cpuname = "Unknown";
break;
}
+ /* Check Longhaul ver. 2 */
+ if (longhaul_version == TYPE_LONGHAUL_V2) {
+ rdmsr(MSR_VIA_LONGHAUL, lo, hi);
+ if (lo == 0 && hi == 0)
+ /* Looks like MSR isn't present */
+ longhaul_version = TYPE_LONGHAUL_V1;
+ }
printk (KERN_INFO PFX "VIA %s CPU detected. ", cpuname);
switch (longhaul_version) {