+if ETRAX_ARCH_V10
+
+menu "CRIS v10 options"
+
# ETRAX 100LX v1 has a MMU "feature" requiring a low mapping
config CRIS_LOW_MAP
bool
help
The ETRAX network driver is responsible for flashing LED's when
packets arrive and are sent. It uses macros defined in
- <file:include/asm-cris/io.h>, and those macros are defined after what
- YOU choose in this option. The actual bits used are configured
+ <file:arch/cris/include/asm/io.h>, and those macros are defined after
+ what YOU choose in this option. The actual bits used are configured
separately. Select this if the LEDs are on port PA. Some products
put the leds on PB or a memory-mapped latch (CSP0) instead.
help
The ETRAX network driver is responsible for flashing LED's when
packets arrive and are sent. It uses macros defined in
- <file:include/asm-cris/io.h>, and those macros are defined after what
- YOU choose in this option. The actual bits used are configured
+ <file:arch/cris/include/asm/io.h>, and those macros are defined after
+ what YOU choose in this option. The actual bits used are configured
separately. Select this if the LEDs are on port PB. Some products
put the leds on PA or a memory-mapped latch (CSP0) instead.
help
The ETRAX network driver is responsible for flashing LED's when
packets arrive and are sent. It uses macros defined in
- <file:include/asm-cris/io.h>, and those macros are defined after what
- YOU choose in this option. The actual bits used are configured
+ <file:arch/cris/include/asm/io.h>, and those macros are defined after
+ what YOU choose in this option. The actual bits used are configured
separately. Select this if the LEDs are on a memory-mapped latch
using chip select CSP0, this is mapped at 0x90000000.
Some products put the leds on PA or PB instead.
set this to same as CONFIG_ETRAX_LED1G (normally 2).
config ETRAX_LED8Y
- int "Eigth yellow LED bit"
+ int "Eighth yellow LED bit"
depends on ETRAX_CSP0_LEDS
default "2"
help
For products with only one or two controllable LEDs,
set this to same as CONFIG_ETRAX_LED1G (normally 2).
-choice
- prompt "Product debug-port"
- depends on ETRAX_ARCH_V10
- default ETRAX_DEBUG_PORT0
-
-config ETRAX_DEBUG_PORT0
- bool "Serial-0"
- help
- Choose a serial port for the ETRAX debug console. Default to
- port 0.
-
-config ETRAX_DEBUG_PORT1
- bool "Serial-1"
- help
- Use serial port 1 for the console.
-
-config ETRAX_DEBUG_PORT2
- bool "Serial-2"
- help
- Use serial port 2 for the console.
-
-config ETRAX_DEBUG_PORT3
- bool "Serial-3"
- help
- Use serial port 3 for the console.
-
-config ETRAX_DEBUG_PORT_NULL
- bool "disabled"
- help
- Disable serial-port debugging.
-
-endchoice
-
-choice
- prompt "Kernel GDB port"
- depends on ETRAX_KGDB
- default ETRAX_KGDB_PORT0
- help
- Choose a serial port for kernel debugging. NOTE: This port should
- not be enabled under Drivers for built-in interfaces (as it has its
- own initialization code) and should not be the same as the debug port.
-
-config ETRAX_KGDB_PORT0
- bool "Serial-0"
- help
- Use serial port 0 for kernel debugging.
-
-config ETRAX_KGDB_PORT1
- bool "Serial-1"
- help
- Use serial port 1 for kernel debugging.
-
-config ETRAX_KGDB_PORT2
- bool "Serial-2"
- help
- Use serial port 2 for kernel debugging.
-
-config ETRAX_KGDB_PORT3
- bool "Serial-3"
- help
- Use serial port 3 for kernel debugging.
-
-endchoice
choice
prompt "Product rescue-port"
depends on ETRAX_ARCH_V10
default "95a6"
help
- Waitstates for SRAM, Flash and peripherials (not DRAM). 95f8 is a
+ Waitstates for SRAM, Flash and peripherals (not DRAM). 95f8 is a
good choice for most Axis products...
config ETRAX_DEF_R_BUS_CONFIG
default "25"
help
Configure where power button is connected.
+
+endmenu
+
+endif