#include <plat/omap-pm.h>
#include <plat/mux.h>
#include <plat/omap_device.h>
+#include <asm/mach-types.h>
#include "mux.h"
#include "hsmmc.h"
* Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
* card with Vcc regulator (from twl4030 or whatever). OMAP has both
* 1.8V and 3.0V modes, controlled by the PBIAS register.
- *
- * In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
- * is most naturally TWL VSIM; those pins also use PBIAS.
- *
- * FIXME handle VMMC1A as needed ...
*/
reg = omap4_ctrl_pad_readl(control_pbias_offset);
reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
- OMAP4_MMC1_PWRDNZ_MASK);
+ OMAP4_MMC1_PWRDNZ_MASK |
+ OMAP4_MMC1_PBIASLITE_VMODE_MASK);
omap4_ctrl_pad_writel(reg, control_pbias_offset);
}
reg &= ~(OMAP4_MMC1_PWRDNZ_MASK);
omap4_ctrl_pad_writel(reg, control_pbias_offset);
}
- } else {
- reg = omap4_ctrl_pad_readl(control_pbias_offset);
- reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
- OMAP4_MMC1_PWRDNZ_MASK |
- OMAP4_MMC1_PBIASLITE_VMODE_MASK);
- omap4_ctrl_pad_writel(reg, control_pbias_offset);
}
}
-static void hsmmc23_before_set_reg(struct device *dev, int slot,
+static void hsmmc2_before_set_reg(struct device *dev, int slot,
int power_on, int vdd)
{
struct omap_mmc_platform_data *mmc = dev->platform_data;
mmc->slots[0].remux(dev, slot, power_on);
if (power_on) {
- /* Only MMC2 supports a CLKIN */
- if (mmc->slots[0].internal_clock) {
- u32 reg;
+ u32 reg;
- reg = omap_ctrl_readl(control_devconf1_offset);
+ reg = omap_ctrl_readl(control_devconf1_offset);
+ if (mmc->slots[0].internal_clock)
reg |= OMAP2_MMCSDIO2ADPCLKISEL;
- omap_ctrl_writel(reg, control_devconf1_offset);
- }
+ else
+ reg &= ~OMAP2_MMCSDIO2ADPCLKISEL;
+ omap_ctrl_writel(reg, control_devconf1_offset);
}
}
static inline void omap_hsmmc_mux(struct omap_mmc_platform_data *mmc_controller,
int controller_nr)
{
- if (gpio_is_valid(mmc_controller->slots[0].switch_pin))
+ if (gpio_is_valid(mmc_controller->slots[0].switch_pin) &&
+ (mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
omap_mux_init_gpio(mmc_controller->slots[0].switch_pin,
OMAP_PIN_INPUT_PULLUP);
- if (gpio_is_valid(mmc_controller->slots[0].gpio_wp))
+ if (gpio_is_valid(mmc_controller->slots[0].gpio_wp) &&
+ (mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES))
omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
OMAP_PIN_INPUT_PULLUP);
if (cpu_is_omap34xx()) {
c->caps &= ~MMC_CAP_8_BIT_DATA;
c->caps |= MMC_CAP_4_BIT_DATA;
}
- /* FALLTHROUGH */
- case 3:
if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
/* off-chip level shifting, or none */
- mmc->slots[0].before_set_reg = hsmmc23_before_set_reg;
+ mmc->slots[0].before_set_reg = hsmmc2_before_set_reg;
mmc->slots[0].after_set_reg = NULL;
}
break;
+ case 3:
case 4:
case 5:
mmc->slots[0].before_set_reg = NULL;
return 0;
}
-static struct omap_device_pm_latency omap_hsmmc_latency[] = {
- [0] = {
- .deactivate_func = omap_device_idle_hwmods,
- .activate_func = omap_device_enable_hwmods,
- .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST,
- },
- /*
- * XXX There should also be an entry here to power off/on the
- * MMC regulators/PBIAS cells, etc.
- */
-};
-
#define MAX_OMAP_MMC_HWMOD_NAME_LEN 16
void __init omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr)
{
struct omap_hwmod *oh;
struct platform_device *pdev;
- struct omap_device_pm_latency *ohl;
char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN];
struct omap_mmc_platform_data *mmc_data;
struct omap_mmc_dev_attr *mmc_dev_attr;
char *name;
int l;
- int ohl_cnt = 0;
mmc_data = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
if (!mmc_data) {
omap_hsmmc_mux(mmc_data, (ctrl_nr - 1));
name = "omap_hsmmc";
- ohl = omap_hsmmc_latency;
- ohl_cnt = ARRAY_SIZE(omap_hsmmc_latency);
l = snprintf(oh_name, MAX_OMAP_MMC_HWMOD_NAME_LEN,
"mmc%d", ctrl_nr);
if (oh->dev_attr != NULL) {
mmc_dev_attr = oh->dev_attr;
mmc_data->controller_flags = mmc_dev_attr->flags;
+ /*
+ * erratum 2.1.1.128 doesn't apply if board has
+ * a transceiver is attached
+ */
+ if (hsmmcinfo->transceiver)
+ mmc_data->controller_flags &=
+ ~OMAP_HSMMC_BROKEN_MULTIBLOCK_READ;
}
pdev = omap_device_build(name, ctrl_nr - 1, oh, mmc_data,
- sizeof(struct omap_mmc_platform_data), ohl, ohl_cnt, false);
+ sizeof(struct omap_mmc_platform_data), NULL, 0, false);
if (IS_ERR(pdev)) {
WARN(1, "Can't build omap_device for %s:%s.\n", name, oh->name);
kfree(mmc_data->slots[0].name);
control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
control_devconf1_offset = OMAP343X_CONTROL_DEVCONF1;
}
+
+ if (machine_is_omap3_pandora()) {
+ /* needed for gpio_126 - gpio_129 to work correctly */
+ reg = omap_ctrl_readl(control_pbias_offset);
+ reg &= ~OMAP343X_PBIASLITEVMODE1;
+ omap_ctrl_writel(reg, control_pbias_offset);
+ }
} else {
control_pbias_offset =
OMAP4_CTRL_MODULE_PAD_CORE_CONTROL_PBIASLITE;
OMAP4_SDMMC1_PUSTRENGTH_GRP1_MASK);
reg &= ~(OMAP4_SDMMC1_PUSTRENGTH_GRP2_MASK |
OMAP4_SDMMC1_PUSTRENGTH_GRP3_MASK);
- reg |= (OMAP4_USBC1_DR0_SPEEDCTRL_MASK|
+ reg |= (OMAP4_SDMMC1_DR0_SPEEDCTRL_MASK |
OMAP4_SDMMC1_DR1_SPEEDCTRL_MASK |
OMAP4_SDMMC1_DR2_SPEEDCTRL_MASK);
omap4_ctrl_pad_writel(reg, control_mmc1);