#include <plat/common.h>
#include <plat/mcspi.h>
#include <plat/display.h>
+#include <plat/panel-generic-dpi.h>
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
dvi_enabled = 0;
}
+static struct panel_generic_dpi_data dvi_panel = {
+ .name = "generic",
+ .platform_enable = omap3_evm_enable_dvi,
+ .platform_disable = omap3_evm_disable_dvi,
+};
+
static struct omap_dss_device omap3_evm_dvi_device = {
.name = "dvi",
- .driver_name = "generic_panel",
.type = OMAP_DISPLAY_TYPE_DPI,
+ .driver_name = "generic_dpi_panel",
+ .data = &dvi_panel,
.phy.dpi.data_lines = 24,
- .platform_enable = omap3_evm_enable_dvi,
- .platform_disable = omap3_evm_disable_dvi,
};
static struct omap_dss_device *omap3_evm_dss_devices[] = {
{
omap_board_config = omap3_evm_config;
omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
- omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL);
+ omap2_init_common_infrastructure();
+ omap2_init_common_devices(mt46h32m32lf6_sdrc_params, NULL);
omap_init_irq();
- omap_gpio_init();
}
static struct platform_device *omap3_evm_devices[] __initdata = {
&omap3_evm_dss_device,
};
-static struct ehci_hcd_omap_platform_data ehci_pdata __initdata = {
+static struct usbhs_omap_board_data usbhs_bdata __initdata = {
- .port_mode[0] = EHCI_HCD_OMAP_MODE_UNKNOWN,
- .port_mode[1] = EHCI_HCD_OMAP_MODE_PHY,
- .port_mode[2] = EHCI_HCD_OMAP_MODE_UNKNOWN,
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.phy_reset = true,
/* PHY reset GPIO will be runtime programmed based on EVM version */
OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
-#else
-#define board_mux NULL
#endif
static struct omap_musb_board_data musb_board_data = {
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
- ehci_pdata.reset_gpio_port[1] = 21;
+ usbhs_bdata.reset_gpio_port[1] = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
- ehci_pdata.reset_gpio_port[1] = 135;
+ usbhs_bdata.reset_gpio_port[1] = 135;
}
usb_musb_init(&musb_board_data);
- usb_ehci_init(&ehci_pdata);
+ usbhs_init(&usbhs_bdata);
ads7846_dev_init();
omap3evm_init_smsc911x();
omap3_evm_display_init();