#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
+#include <asm/arch/tc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/mux.h>
#include <asm/arch/fpga.h>
#include <asm/arch/common.h>
+#include <asm/arch/board.h>
static struct resource smc91x_resources[] = {
[0] = {
},
};
-static int __initdata p2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 0};
-
static struct mtd_partition p2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
};
static struct resource p2_flash_resource = {
- .start = OMAP_FLASH_0_START,
- .end = OMAP_FLASH_0_START + OMAP_FLASH_0_SIZE - 1,
+ .start = OMAP_CS0_PHYS,
+ .end = OMAP_CS0_PHYS + SZ_32M - 1,
.flags = IORESOURCE_MEM,
};
&smc91x_device,
};
+static struct omap_uart_config perseus2_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1)),
+};
+
+static struct omap_lcd_config perseus2_lcd_config __initdata = {
+ .panel_name = "p2",
+ .ctrl_name = "internal",
+};
+
+static struct omap_board_config_kernel perseus2_config[] = {
+ { OMAP_TAG_UART, &perseus2_uart_config },
+ { OMAP_TAG_LCD, &perseus2_lcd_config },
+};
+
static void __init omap_perseus2_init(void)
{
(void) platform_add_devices(devices, ARRAY_SIZE(devices));
+
+ omap_board_config = perseus2_config;
+ omap_board_config_size = ARRAY_SIZE(perseus2_config);
+ omap_serial_init();
}
static void __init perseus2_init_smc91x(void)
omap_gpio_init();
perseus2_init_smc91x();
}
-
/* Only FPGA needs to be mapped here. All others are done with ioremap */
static struct map_desc omap_perseus2_io_desc[] __initdata = {
- {H2P2_DBG_FPGA_BASE, H2P2_DBG_FPGA_START, H2P2_DBG_FPGA_SIZE,
- MT_DEVICE},
+ {
+ .virtual = H2P2_DBG_FPGA_BASE,
+ .pfn = __phys_to_pfn(H2P2_DBG_FPGA_START),
+ .length = H2P2_DBG_FPGA_SIZE,
+ .type = MT_DEVICE
+ }
};
static void __init omap_perseus2_map_io(void)
omap_writel(0x00000088, OMAP730_FLASH_ACFG_0);
/*
- * Ethernet support trough the debug board
+ * Ethernet support through the debug board
* CS1 timings setup
*/
omap_writel(0x0000fff3, OMAP730_FLASH_CFG_1);
* It is used as the Ethernet controller interrupt
*/
omap_writel(omap_readl(OMAP730_IO_CONF_9) & 0x1FFFFFFF, OMAP730_IO_CONF_9);
- omap_serial_init(p2_serial_ports);
}
MACHINE_START(OMAP_PERSEUS2, "OMAP730 Perseus2")