#include <linux/kernel.h>
#include <linux/init.h>
-#include <linux/device.h>
+#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <asm/mach/map.h>
#include <asm/arch/gpio.h>
+#include <asm/arch/mux.h>
#include <asm/arch/tc.h>
#include <asm/arch/usb.h>
#include <asm/arch/common.h>
extern int omap_gpio_init(void);
-static int __initdata h2_serial_ports[OMAP_MAX_NR_PORTS] = {1, 1, 1};
-
static struct mtd_partition h2_partitions[] = {
/* bootloader (U-Boot, etc) in first sector */
{
};
static struct resource h2_flash_resource = {
- .start = OMAP_CS2B_PHYS,
- .end = OMAP_CS2B_PHYS + OMAP_CS2B_SIZE - 1,
+ /* This is on CS3, wherever it's mapped */
.flags = IORESOURCE_MEM,
};
printk("Error requesting gpio 0 for smc91x irq\n");
return;
}
- omap_set_gpio_edge_ctrl(0, OMAP_GPIO_FALLING_EDGE);
}
-void h2_init_irq(void)
+static void __init h2_init_irq(void)
{
omap_init_irq();
omap_gpio_init();
};
static struct omap_mmc_config h2_mmc_config __initdata = {
- .mmc_blocks = 1,
- .mmc1_power_pin = -1, /* tps65010 gpio3 */
- .mmc1_switch_pin = OMAP_MPUIO(1),
+ .mmc [0] = {
+ .enabled = 1,
+ .wire4 = 1,
+ .wp_pin = OMAP_MPUIO(3),
+ .power_pin = -1, /* tps65010 gpio3 */
+ .switch_pin = OMAP_MPUIO(1),
+ },
+};
+
+static struct omap_uart_config h2_uart_config __initdata = {
+ .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)),
+};
+
+static struct omap_lcd_config h2_lcd_config __initdata = {
+ .panel_name = "h2",
+ .ctrl_name = "internal",
};
static struct omap_board_config_kernel h2_config[] = {
{ OMAP_TAG_USB, &h2_usb_config },
{ OMAP_TAG_MMC, &h2_mmc_config },
+ { OMAP_TAG_UART, &h2_uart_config },
+ { OMAP_TAG_LCD, &h2_lcd_config },
};
static void __init h2_init(void)
{
+ /* NOTE: revC boards support NAND-boot, which can put NOR on CS2B
+ * and NAND (either 16bit or 8bit) on CS3.
+ */
+ h2_flash_resource.end = h2_flash_resource.start = omap_cs3_phys();
+ h2_flash_resource.end += SZ_32M - 1;
+
+ /* MMC: card detect and WP */
+ // omap_cfg_reg(U19_ARMIO1); /* CD */
+ omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
+
platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
omap_board_config = h2_config;
omap_board_config_size = ARRAY_SIZE(h2_config);
+ omap_serial_init();
}
static void __init h2_map_io(void)
{
omap_map_common_io();
- omap_serial_init(h2_serial_ports);
}
MACHINE_START(OMAP_H2, "TI-H2")