<file:Documentation/mca.txt> (and especially the web page given
there) before attempting to build an MCA bus kernel.
+config GENERIC_HARDIRQS
+ bool
+ default y
+
+config TRACE_IRQFLAGS_SUPPORT
+ bool
+ default y
+
+config HARDIRQS_SW_RESEND
+ bool
+ default y
+
+config GENERIC_IRQ_PROBE
+ bool
+ default y
+
config RWSEM_GENERIC_SPINLOCK
bool
default y
help
Support for Motorola's i.MX family of processors (MX1, MXL).
-config ARCH_IOP3XX
- bool "IOP3xx-based"
+config ARCH_IOP32X
+ bool "IOP32x-based"
+ depends on MMU
+ select PLAT_IOP
+ select PCI
+ help
+ Support for Intel's 80219 and IOP32X (XScale) family of
+ processors.
+
+config ARCH_IOP33X
+ bool "IOP33x-based"
depends on MMU
+ select PLAT_IOP
select PCI
help
- Support for Intel's IOP3XX (XScale) family of processors.
+ Support for Intel's IOP33X (XScale) family of processors.
config ARCH_IXP4XX
bool "IXP4xx-based"
source "arch/arm/mach-integrator/Kconfig"
-source "arch/arm/mach-iop3xx/Kconfig"
+source "arch/arm/mach-iop32x/Kconfig"
+
+source "arch/arm/mach-iop33x/Kconfig"
source "arch/arm/mach-ixp4xx/Kconfig"
config ARCH_ACORN
bool
+config PLAT_IOP
+ bool
+
source arch/arm/mm/Kconfig
# bool 'Use XScale PMU as timer source' CONFIG_XSCALE_PMU_TIMER
ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \
ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \
ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \
- ARCH_AT91RM9200
+ ARCH_AT91RM9200 || MACH_TRIZEPS4
help
If you say Y here, the LEDs on your machine will be used
to provide useful information about your current system status.
config ALIGNMENT_TRAP
bool
+ depends on CPU_CP15_MMU
default y if !ARCH_EBSA110
help
ARM processors can not fetch/store information which is not
hex "Compressed ROM boot loader BSS address"
default "0"
help
- The base address of 64KiB of read/write memory in the target
- for the ROM-able zImage, which must be available while the
- decompressor is running. Platforms which normally make use of
- ROM-able zImage formats normally set this to a suitable
- value in their defconfig file.
+ The base address of an area of read/write memory in the target
+ for the ROM-able zImage which must be available while the
+ decompressor is running. It must be large enough to hold the
+ entire decompressed kernel plus an additional 128 KiB.
+ Platforms which normally make use of ROM-able zImage formats
+ normally set this to a suitable value in their defconfig file.
If ZBOOT_ROM is not enabled, this has no effect.
source "drivers/connector/Kconfig"
-if ALIGNMENT_TRAP
+if ALIGNMENT_TRAP || !CPU_CP15_MMU
source "drivers/mtd/Kconfig"
endif
source "drivers/acorn/block/Kconfig"
-if PCMCIA || ARCH_CLPS7500 || ARCH_IOP3XX || ARCH_IXP4XX \
+if PCMCIA || ARCH_CLPS7500 || ARCH_IOP32X || ARCH_IOP33X || ARCH_IXP4XX \
|| ARCH_L7200 || ARCH_LH7A40X || ARCH_PXA || ARCH_RPC \
|| ARCH_S3C2410 || ARCH_SA1100 || ARCH_SHARK || FOOTBRIDGE \
|| ARCH_IXP23XX