CONFIG_LBA48
Set this to enable support for disks larger than 137GB
- Also look at CONFIG_SYS_64BIT_LBA ,CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
+ Also look at CONFIG_SYS_64BIT_LBA.
Whithout these , LBA48 support uses 32bit variables and will 'only'
support disks up to 2.1TB.
- NETWORK Support (other):
+ CONFIG_DRIVER_AT91EMAC
+ Support for AT91RM9200 EMAC.
+
+ CONFIG_RMII
+ Define this to use reduced MII inteface
+
+ CONFIG_DRIVER_AT91EMAC_QUIET
+ If this defined, the driver is quiet.
+ The driver doen't show link status messages.
+
CONFIG_DRIVER_LAN91C96
Support for SMSC's LAN91C96 chips.
- CONFIG_SYS_EEPROM_SIZE:
The size in bytes of the EEPROM device.
+ - CONFIG_ENV_EEPROM_IS_ON_I2C
+ define this, if you have I2C and SPI activated, and your
+ EEPROM, which holds the environment, is on the I2C bus.
+
+ - CONFIG_I2C_ENV_EEPROM_BUS
+ if you have an Environment on an EEPROM reached over
+ I2C muxes, you can define here, how to reach this
+ EEPROM. For example:
+
+ #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
+
+ EEPROM which holds the environment, is reached over
+ a pca9547 i2c mux with address 0x70, channel 3.
- CONFIG_ENV_IS_IN_DATAFLASH:
- CONFIG_SYS_FAULT_MII_ADDR:
MII address of the PHY to check for the Ethernet link state.
-- CONFIG_SYS_64BIT_VSPRINTF:
- Makes vsprintf (and all *printf functions) support printing
- of 64bit values by using the L quantifier
-
-- CONFIG_SYS_64BIT_STRTOUL:
- Adds simple_strtoull that returns a 64bit value
-
- CONFIG_NS16550_MIN_FUNCTIONS:
Define this if you desire to only have use of the NS16550_init
and NS16550_putc functions for the serial driver located at
working with an in-memory copy. In case the Flash area containing the
environment is erased by accident, a default environment is provided.
-Some configuration options can be set using Environment Variables:
+Some configuration options can be set using Environment Variables.
+
+List of environment variables (most likely not complete):
baudrate - see CONFIG_BAUDRATE
available network interfaces.
It just stays at the currently selected interface.
- netretry - When set to "no" each network operation will
+ netretry - When set to "no" each network operation will
either succeed or fail without retrying.
When set to "once" the network operation will
fail when all the available network interfaces
tftpdstport - If this is set, the value is used for TFTP's UDP
destination port instead of the Well Know Port 69.
- vlan - When set to a value < 4095 the traffic over
+ tftpblocksize - Block size to use for TFTP transfers; if not set,
+ we use the TFTP server's default block size
+
+ tftptimeout - Retransmission timeout for TFTP packets (in milli-
+ seconds, minimum value is 1000 = 1 second). Defines
+ when a packet is considered to be lost so it has to
+ be retransmitted. The default is 5000 = 5 seconds.
+ Lowering this value may make downloads succeed
+ faster in networks with high packet loss rates or
+ with unreliable TFTP servers.
+
+ vlan - When set to a value < 4095 the traffic over
Ethernet is encapsulated/received over 802.1q
VLAN tagged frames.
R30: GOT pointer
R31: frame pointer
- (U-Boot also uses R14 as internal GOT pointer.)
+ (U-Boot also uses R12 as internal GOT pointer. r12
+ is a volatile register so r12 needs to be reset when
+ going back and forth between asm and C)
==> U-Boot will use R2 to hold a pointer to the global data