acpi_display_output=video
See above.
+ acpi_early_pdc_eval [HW,ACPI] Evaluate processor _PDC methods
+ early. Needed on some platforms to properly
+ initialize the EC.
+
acpi_irq_balance [HW,ACPI]
ACPI will balance active IRQs
default in APIC mode
acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
- old_ordering, s4_nonvs }
+ old_ordering, s4_nonvs, sci_force_enable }
See Documentation/power/video.txt for information on
s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
of _PTS is used by default).
s4_nonvs prevents the kernel from saving/restoring the
ACPI NVS memory during hibernation.
+ sci_force_enable causes the kernel to set SCI_EN directly
+ on resume from S1/S3 (which is against the ACPI spec,
+ but some broken systems don't work without it).
acpi_use_timer_override [HW,ACPI]
Use timer override. For some broken Nvidia NF5 boards
aic79xx= [HW,SCSI]
See Documentation/scsi/aic79xx.txt.
+ alignment= [KNL,ARM]
+ Allow the default userspace alignment fault handler
+ behaviour to be specified. Bit 0 enables warnings,
+ bit 1 enables fixups, and bit 2 sends a segfault.
+
amd_iommu= [HW,X86-84]
Pass parameters to the AMD IOMMU driver in the system.
Possible values are:
No delay
ip= [IP_PNP]
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
See comment before ip2_setup() in
going to be removed in 2.6.29.
nfsaddrs= [NFS]
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
nfsroot= [NFS] nfs root filesystem for disk-less boxes.
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
nfs.callback_tcpport=
[NFS] set the TCP port on which the NFSv4 callback
nomfgpt [X86-32] Disable Multi-Function General Purpose
Timer usage (for AMD Geode machines).
+ nopat [X86] Disable PAT (page attribute table extension of
+ pagetables) support.
+
norandmaps Don't use address space randomization. Equivalent to
echo 0 > /proc/sys/kernel/randomize_va_space
waiting for the ACK, so if this is set too high
interrupts *may* be lost!
+ omap_mux= [OMAP] Override bootloader pin multiplexing.
+ Format: <mux_mode0.mode_name=value>...
+ For example, to override I2C bus2:
+ omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
+
opl3= [HW,OSS]
Format: <io>
IRQ routing is enabled.
noacpi [X86] Do not use ACPI for IRQ routing
or for PCI scanning.
- use_crs [X86] Use _CRS for PCI resource
- allocation.
+ use_crs [X86] Use PCI host bridge window information
+ from ACPI. On BIOSes from 2008 or later, this
+ is enabled by default. If you need to use this,
+ please report a bug.
+ nocrs [X86] Ignore PCI host bridge windows from ACPI.
+ If you need to use this, please report a bug.
routeirq Do IRQ routing for all PCI devices.
This is normally done in pci_enable_device(),
so this option is a temporary workaround
force Enable ASPM even on devices that claim not to support it.
WARNING: Forcing ASPM on may cause system lockups.
+ pcie_pme= [PCIE,PM] Native PCIe PME signaling options:
+ off Do not use native PCIe PME signaling.
+ force Use native PCIe PME signaling even if the BIOS refuses
+ to allow the kernel to control the relevant PCIe config
+ registers.
+ nomsi Do not use MSI for native PCIe PME signaling (this makes
+ all PCIe root ports use INTx for everything).
+
pcmv= [HW,PCMCIA] BadgePAD 4
pd. [PARIDE]
vmpoff= [KNL,S390] Perform z/VM CP command after power off.
Format: <command>
+ vt.cur_default= [VT] Default cursor shape.
+ Format: 0xCCBBAA, where AA, BB, and CC are the same as
+ the parameters of the <Esc>[?A;B;Cc escape sequence;
+ see VGA-softcursor.txt. Default: 2 = underline.
+
vt.default_blu= [VT]
Format: <blue0>,<blue1>,<blue2>,...,<blue15>
Change the default blue palette of the console.