ISAPNP ISA PnP code is enabled.
ISDN Appropriate ISDN support is enabled.
JOY Appropriate joystick support is enabled.
+ LIBATA Libata driver is enabled
LP Printer support is enabled.
LOOP Loopback device support is enabled.
M68k M68k architecture is enabled.
Documentation/scsi/.
SELINUX SELinux support is enabled.
SERIAL Serial support is enabled.
+ SH SuperH architecture is enabled.
SMP The kernel is an SMP kernel.
SPARC Sparc architecture is enabled.
SWSUSP Software suspend is enabled.
See header of drivers/scsi/53c7xx.c.
See also Documentation/scsi/ncr53c7xx.txt.
- acpi= [HW,ACPI] Advanced Configuration and Power Interface
+ acpi= [HW,ACPI,X86-64,i386]
+ Advanced Configuration and Power Interface
Format: { force | off | ht | strict | noirq }
force -- enable ACPI if default was off
off -- disable ACPI if default was on
See also Documentation/pm.txt, pci=noacpi
+ acpi_apic_instance= [ACPI, IOAPIC]
+ Format: <int>
+ 2: use 2nd APIC table, if available
+ 1,0: use 1st APIC table
+ default: 0
+
acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode }
See Documentation/power/video.txt
dtc3181e= [HW,SCSI]
- earlyprintk= [IA-32,X86-64]
+ earlyprintk= [IA-32,X86-64,SH]
earlyprintk=vga
earlyprintk=serial[,ttySn[,baudrate]]
lapic [IA-32,APIC] Enable the local APIC even if BIOS
disabled it.
+ lapic_timer_c2_ok [IA-32,x86-64,APIC] trust the local apic timer in
+ C2 power state.
+
lasi= [HW,SCSI] PARISC LASI driver for the 53c700 chip
Format: addr:<io>,irq:<irq>
Format: <1-256>
maxcpus= [SMP] Maximum number of processors that an SMP kernel
- should make use of
+ should make use of.
+ Using "nosmp" or "maxcpus=0" will disable SMP
+ entirely (the MPS table probe still happens, though).
+ A command-line option of "maxcpus=<NUM>", where <NUM>
+ is an integer greater than 0, limits the maximum number
+ of CPUs activated in SMP mode to <NUM>.
+ Using "maxcpus=1" on an SMP kernel is the trivial
+ case of an SMP kernel with only one CPU.
max_addr=[KMG] [KNL,BOOT,ia64] All physical memory greater than or
equal to this physical address is ignored.
emulation library even if a 387 maths coprocessor
is present.
+ noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
+ when set.
+ Format: <int>
+
noaliencache [MM, NUMA] Disables the allcoation of alien caches in
the slab allocator. Saves per-node memory, but will
impact performance on real NUMA hardware.
nolapic [IA-32,APIC] Do not enable or use the local APIC.
+ nolapic_timer [IA-32,APIC] Do not use the local APIC timer.
+
noltlbs [PPC] Do not use large page/tlb entries for kernel
lowmem mapping on PPC40x.
stifb= [HW]
Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
+ sunrpc.pool_mode=
+ [NFS]
+ Control how the NFS server code allocates CPUs to
+ service thread pools. Depending on how many NICs
+ you have and where their interrupts are bound, this
+ option will affect which CPUs will do NFS serving.
+ Note: this parameter cannot be changed while the
+ NFS server is running.
+
+ auto the server chooses an appropriate mode
+ automatically using heuristics
+ global a single global pool contains all CPUs
+ percpu one pool for each CPU
+ pernode one pool for each NUMA node (equivalent
+ to global on non-NUMA machines)
+
swiotlb= [IA-64] Number of I/O TLB slabs
switches= [HW,M68k]
Note that genuine overcurrent events won't be
reported either.
+ usbcore.autosuspend=
+ [USB] The autosuspend time delay (in seconds) used
+ for newly-detected USB devices (default 2). This
+ is the time required before an idle device will be
+ autosuspended. Devices for which the delay is set
+ to 0 won't be autosuspended at all.
+
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
- vdso= [IA-32]
+ vdso= [IA-32,SH]
vdso=1: enable VDSO (default)
vdso=0: disable VDSO mapping