Supported chips:
* Winbond W83781D
Prefix: 'w83781d'
- Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
+ Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83781d.pdf
* Winbond W83782D
Prefix: 'w83782d'
- Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
+ Addresses scanned: I2C 0x28 - 0x2f, ISA 0x290 (8 I/O ports)
Datasheet: http://www.winbond.com/PDF/sheet/w83782d.pdf
* Winbond W83783S
Prefix: 'w83783s'
Addresses scanned: I2C 0x2d
Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/w83783s.pdf
- * Winbond W83627HF
- Prefix: 'w83627hf'
- Addresses scanned: I2C 0x20 - 0x2f, ISA 0x290 (8 I/O ports)
- Datasheet: http://www.winbond.com/PDF/sheet/w83627hf.pdf
* Asus AS99127F
Prefix: 'as99127f'
Addresses scanned: I2C 0x28 - 0x2f
Description
-----------
-This driver implements support for the Winbond W83781D, W83782D, W83783S,
-W83627HF chips, and the Asus AS99127F chips. We will refer to them
-collectively as W8378* chips.
+This driver implements support for the Winbond W83781D, W83782D, W83783S
+chips, and the Asus AS99127F chips. We will refer to them collectively as
+W8378* chips.
There is quite some difference between these chips, but they are similar
enough that it was sensible to put them together in one driver.
-The W83627HF chip is assumed to be identical to the ISA W83782D.
The Asus chips are similar to an I2C-only W83782D.
Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA
as99127f 7 3 0 3 0x31 0x12c3 yes no
as99127f rev.2 (type_name = as99127f) 0x31 0x5ca3 yes no
w83781d 7 3 0 3 0x10-1 0x5ca3 yes yes
-w83627hf 9 3 2 3 0x21 0x5ca3 yes yes(LPC)
w83782d 9 3 2-4 3 0x30 0x5ca3 yes yes
w83783s 5-6 3 2 1-2 0x40 0x5ca3 yes no
0x000400: in6
0x000800: fan3
0x001000: chassis
-0x002000: temp3 (W83782D and W83627HF only)
-0x010000: in7 (W83782D and W83627HF only)
-0x020000: in8 (W83782D and W83627HF only)
+0x002000: temp3 (W83782D only)
+0x010000: in7 (W83782D only)
+0x020000: in8 (W83782D only)
If an alarm triggers, it will remain triggered until the hardware register
is read at least once. This means that the cause for the alarm may
# PWM
-Additional info about PWM on the AS99127F (may apply to other Asus
+* Additional info about PWM on the AS99127F (may apply to other Asus
chips as well) by Jean Delvare as of 2004-04-09:
AS99127F revision 2 seems to have two PWM registers at 0x59 and 0x5A,
long as we don't know more, the w83781d driver doesn't handle PWM on
AS99127F chips at all.
-Additional info about PWM on the AS99127F rev.1 by Hector Martin:
+* Additional info about PWM on the AS99127F rev.1 by Hector Martin:
I've been fiddling around with the (in)famous 0x59 register and
found out the following values do work as a form of coarse pwm:
My mobo is an ASUS A7V266-E. This behavior is similar to what I got
with speedfan under Windows, where 0-15% would be off, 15-2x% (can't
remember the exact value) would be 70% and higher would be full on.
+
+* Additional info about PWM on the AS99127F rev.1 from lm-sensors
+ ticket #2350:
+
+I conducted some experiment on Asus P3B-F motherboard with AS99127F
+(Ver. 1).
+
+I confirm that 0x59 register control the CPU_Fan Header on this
+motherboard, and 0x5a register control PWR_Fan.
+
+In order to reduce the dependency of specific fan, the measurement is
+conducted with a digital scope without fan connected. I found out that
+P3B-F actually output variable DC voltage on fan header center pin,
+looks like PWM is filtered on this motherboard.
+
+Here are some of measurements:
+
+0x80 20 mV
+0x81 20 mV
+0x82 232 mV
+0x83 1.2 V
+0x84 2.31 V
+0x85 3.44 V
+0x86 4.62 V
+0x87 5.81 V
+0x88 7.01 V
+9x89 8.22 V
+0x8a 9.42 V
+0x8b 10.6 V
+0x8c 11.9 V
+0x8d 12.4 V
+0x8e 12.4 V
+0x8f 12.4 V
git.openpandora.org / pandora-kernel.git / blobdiff