- i) Freescale QUICC Engine module (QE)
- This represents qe module that is installed on PowerQUICC II Pro.
-
- NOTE: This is an interim binding; it should be updated to fit
- in with the CPM binding later in this document.
-
- Basically, it is a bus of devices, that could act more or less
- as a complete entity (UCC, USB etc ). All of them should be siblings on
- the "root" qe node, using the common properties from there.
- The description below applies to the qe of MPC8360 and
- more nodes and properties would be extended in the future.
-
- i) Root QE device
-
- Required properties:
- - compatible : should be "fsl,qe";
- - model : precise model of the QE, Can be "QE", "CPM", or "CPM2"
- - reg : offset and length of the device registers.
- - bus-frequency : the clock frequency for QUICC Engine.
-
- Recommended properties
- - brg-frequency : the internal clock source frequency for baud-rate
- generators in Hz.
-
- Example:
- qe@e0100000 {
- #address-cells = <1>;
- #size-cells = <1>;
- #interrupt-cells = <2>;
- compatible = "fsl,qe";
- ranges = <0 e0100000 00100000>;
- reg = <e0100000 480>;
- brg-frequency = <0>;
- bus-frequency = <179A7B00>;
- }
-
-
- ii) SPI (Serial Peripheral Interface)
-
- Required properties:
- - cell-index : SPI controller index.
- - compatible : should be "fsl,spi".
- - mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example:
- spi@4c0 {
- cell-index = <0>;
- compatible = "fsl,spi";
- reg = <4c0 40>;
- interrupts = <82 0>;
- interrupt-parent = <700>;
- mode = "cpu";
- };
-
-
- iii) USB (Universal Serial Bus Controller)
-
- Required properties:
- - compatible : could be "qe_udc" or "fhci-hcd".
- - mode : the could be "host" or "slave".
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
-
- Example(slave):
- usb@6c0 {
- compatible = "qe_udc";
- reg = <6c0 40>;
- interrupts = <8b 0>;
- interrupt-parent = <700>;
- mode = "slave";
- };
-
-
- iv) UCC (Unified Communications Controllers)
-
- Required properties:
- - device_type : should be "network", "hldc", "uart", "transparent"
- "bisync", "atm", or "serial".
- - compatible : could be "ucc_geth" or "fsl_atm" and so on.
- - cell-index : the ucc number(1-8), corresponding to UCCx in UM.
- - reg : Offset and length of the register set for the device
- - interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
- - interrupt-parent : the phandle for the interrupt controller that
- services interrupts for this device.
- - pio-handle : The phandle for the Parallel I/O port configuration.
- - port-number : for UART drivers, the port number to use, between 0 and 3.
- This usually corresponds to the /dev/ttyQE device, e.g. <0> = /dev/ttyQE0.
- The port number is added to the minor number of the device. Unlike the
- CPM UART driver, the port-number is required for the QE UART driver.
- - soft-uart : for UART drivers, if specified this means the QE UART device
- driver should use "Soft-UART" mode, which is needed on some SOCs that have
- broken UART hardware. Soft-UART is provided via a microcode upload.
- - rx-clock-name: the UCC receive clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
- - tx-clock-name: the UCC transmit clock source
- "none": clock source is disabled
- "brg1" through "brg16": clock source is BRG1-BRG16, respectively
- "clk1" through "clk24": clock source is CLK1-CLK24, respectively
- The following two properties are deprecated. rx-clock has been replaced
- with rx-clock-name, and tx-clock has been replaced with tx-clock-name.
- Drivers that currently use the deprecated properties should continue to
- do so, in order to support older device trees, but they should be updated
- to check for the new properties first.
- - rx-clock : represents the UCC receive clock source.
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
- - tx-clock: represents the UCC transmit clock source;
- 0x00 : clock source is disabled;
- 0x1~0x10 : clock source is BRG1~BRG16 respectively;
- 0x11~0x28: clock source is QE_CLK1~QE_CLK24 respectively.
-
- Required properties for network device_type:
- - mac-address : list of bytes representing the ethernet address.
- - phy-handle : The phandle for the PHY connected to this controller.
-
- Recommended properties:
- - phy-connection-type : a string naming the controller/PHY interface type,
- i.e., "mii" (default), "rmii", "gmii", "rgmii", "rgmii-id" (Internal
- Delay), "rgmii-txid" (delay on TX only), "rgmii-rxid" (delay on RX only),
- "tbi", or "rtbi".
-
- Example:
- ucc@2000 {
- device_type = "network";
- compatible = "ucc_geth";
- cell-index = <1>;
- reg = <2000 200>;
- interrupts = <a0 0>;
- interrupt-parent = <700>;
- mac-address = [ 00 04 9f 00 23 23 ];
- rx-clock = "none";
- tx-clock = "clk9";
- phy-handle = <212000>;
- phy-connection-type = "gmii";
- pio-handle = <140001>;
- };
-
-
- v) Parallel I/O Ports
-
- This node configures Parallel I/O ports for CPUs with QE support.
- The node should reside in the "soc" node of the tree. For each
- device that using parallel I/O ports, a child node should be created.
- See the definition of the Pin configuration nodes below for more
- information.
-
- Required properties:
- - device_type : should be "par_io".
- - reg : offset to the register set and its length.
- - num-ports : number of Parallel I/O ports
-
- Example:
- par_io@1400 {
- reg = <1400 100>;
- #address-cells = <1>;
- #size-cells = <0>;
- device_type = "par_io";
- num-ports = <7>;
- ucc_pin@01 {
- ......
- };
-
-
- vi) Pin configuration nodes
-
- Required properties:
- - linux,phandle : phandle of this node; likely referenced by a QE
- device.
- - pio-map : array of pin configurations. Each pin is defined by 6
- integers. The six numbers are respectively: port, pin, dir,
- open_drain, assignment, has_irq.
- - port : port number of the pin; 0-6 represent port A-G in UM.
- - pin : pin number in the port.
- - dir : direction of the pin, should encode as follows:
-
- 0 = The pin is disabled
- 1 = The pin is an output
- 2 = The pin is an input
- 3 = The pin is I/O
-
- - open_drain : indicates the pin is normal or wired-OR:
-
- 0 = The pin is actively driven as an output
- 1 = The pin is an open-drain driver. As an output, the pin is
- driven active-low, otherwise it is three-stated.
-
- - assignment : function number of the pin according to the Pin Assignment
- tables in User Manual. Each pin can have up to 4 possible functions in
- QE and two options for CPM.
- - has_irq : indicates if the pin is used as source of external
- interrupts.
-
- Example:
- ucc_pin@01 {
- linux,phandle = <140001>;
- pio-map = <
- /* port pin dir open_drain assignment has_irq */
- 0 3 1 0 1 0 /* TxD0 */
- 0 4 1 0 1 0 /* TxD1 */
- 0 5 1 0 1 0 /* TxD2 */
- 0 6 1 0 1 0 /* TxD3 */
- 1 6 1 0 3 0 /* TxD4 */
- 1 7 1 0 1 0 /* TxD5 */
- 1 9 1 0 2 0 /* TxD6 */
- 1 a 1 0 2 0 /* TxD7 */
- 0 9 2 0 1 0 /* RxD0 */
- 0 a 2 0 1 0 /* RxD1 */
- 0 b 2 0 1 0 /* RxD2 */
- 0 c 2 0 1 0 /* RxD3 */
- 0 d 2 0 1 0 /* RxD4 */
- 1 1 2 0 2 0 /* RxD5 */
- 1 0 2 0 2 0 /* RxD6 */
- 1 4 2 0 2 0 /* RxD7 */
- 0 7 1 0 1 0 /* TX_EN */
- 0 8 1 0 1 0 /* TX_ER */
- 0 f 2 0 1 0 /* RX_DV */
- 0 10 2 0 1 0 /* RX_ER */
- 0 0 2 0 1 0 /* RX_CLK */
- 2 9 1 0 3 0 /* GTX_CLK - CLK10 */
- 2 8 2 0 1 0>; /* GTX125 - CLK9 */
- };
-
- vii) Multi-User RAM (MURAM)
-
- Required properties:
- - compatible : should be "fsl,qe-muram", "fsl,cpm-muram".
- - mode : the could be "host" or "slave".
- - ranges : Should be defined as specified in 1) to describe the
- translation of MURAM addresses.
- - data-only : sub-node which defines the address area under MURAM
- bus that can be allocated as data/parameter
-
- Example:
-
- muram@10000 {
- compatible = "fsl,qe-muram", "fsl,cpm-muram";
- ranges = <0 00010000 0000c000>;
-
- data-only@0{
- compatible = "fsl,qe-muram-data",
- "fsl,cpm-muram-data";
- reg = <0 c000>;
- };
- };
-
- viii) Uploaded QE firmware
-
- If a new firwmare has been uploaded to the QE (usually by the
- boot loader), then a 'firmware' child node should be added to the QE
- node. This node provides information on the uploaded firmware that
- device drivers may need.
-
- Required properties:
- - id: The string name of the firmware. This is taken from the 'id'
- member of the qe_firmware structure of the uploaded firmware.
- Device drivers can search this string to determine if the
- firmware they want is already present.
- - extended-modes: The Extended Modes bitfield, taken from the
- firmware binary. It is a 64-bit number represented
- as an array of two 32-bit numbers.
- - virtual-traps: The virtual traps, taken from the firmware binary.
- It is an array of 8 32-bit numbers.
-
- Example:
-
- firmware {
- id = "Soft-UART";
- extended-modes = <0 0>;
- virtual-traps = <0 0 0 0 0 0 0 0>;
- }
-
- j) CFI or JEDEC memory-mapped NOR flash
git.openpandora.org / pandora-kernel.git / blobdiff