include/configs/ls1012ardb.h

   1 /*
   2  * Copyright 2016 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __LS1012ARDB_H__
   8 #define __LS1012ARDB_H__
   9
  10 #include "ls1012a_common.h"
  11
  12 /* DDR */
  13 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  14 #define CONFIG_CHIP_SELECTS_PER_CTRL    1
  15 #define CONFIG_NR_DRAM_BANKS            2
  16 #define CONFIG_SYS_SDRAM_SIZE           0x40000000
  17 #define CONFIG_CMD_MEMINFO
  18 #define CONFIG_CMD_MEMTEST
  19 #define CONFIG_SYS_MEMTEST_START        0x80000000
  20 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
  21
  22
  23 /*
  24  * I2C IO expander
  25  */
  26
  27 #define I2C_MUX_IO1_ADDR        0x24
  28 #define __SW_BOOT_MASK          0xFC
  29 #define __SW_BOOT_EMU           0x10
  30 #define __SW_BOOT_BANK1         0x00
  31 #define __SW_BOOT_BANK2         0x01
  32 #define __SW_REV_MASK           0x07
  33 #define __SW_REV_A              0xF8
  34 #define __SW_REV_B              0xF0
  35
  36 /*  MMC  */
  37 #ifdef CONFIG_MMC
  38 #define CONFIG_FSL_ESDHC
  39 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
  40 #endif
  41
  42 /* SATA */
  43 #define CONFIG_SCSI_AHCI_PLAT
  44
  45 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  46
  47 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  48 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  49 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  50                                                 CONFIG_SYS_SCSI_MAX_LUN)
  51
  52 #define CONFIG_PCIE1            /* PCIE controller 1 */
  53
  54 #define CONFIG_PCI_SCAN_SHOW
  55
  56 #define CONFIG_CMD_MEMINFO
  57 #define CONFIG_CMD_MEMTEST
  58 #define CONFIG_SYS_MEMTEST_START        0x80000000
  59 #define CONFIG_SYS_MEMTEST_END          0x9fffffff
  60
  61 #undef CONFIG_EXTRA_ENV_SETTINGS
  62 #define CONFIG_EXTRA_ENV_SETTINGS               \
  63         "verify=no\0"                           \
  64         "fdt_high=0xffffffffffffffff\0"         \
  65         "initrd_high=0xffffffffffffffff\0"      \
  66         "fdt_addr=0x00f00000\0"                 \
  67         "kernel_addr=0x01000000\0"              \
  68         "scriptaddr=0x80000000\0"               \
  69         "fdtheader_addr_r=0x80100000\0"         \
  70         "kernelheader_addr_r=0x80200000\0"      \
  71         "kernel_addr_r=0x81000000\0"            \
  72         "fdt_addr_r=0x90000000\0"               \
  73         "load_addr=0xa0000000\0"                \
  74         "kernel_size=0x2800000\0"               \
  75         "console=ttyS0,115200\0"                \
  76         BOOTENV                                 \
  77         "boot_scripts=ls1012ardb_boot.scr\0"    \
  78         "scan_dev_for_boot_part="               \
  79              "part list ${devtype} ${devnum} devplist; "        \
  80              "env exists devplist || setenv devplist 1; "       \
  81              "for distro_bootpart in ${devplist}; do "          \
  82                   "if fstype ${devtype} "                       \
  83                       "${devnum}:${distro_bootpart} "           \
  84                       "bootfstype; then "                       \
  85                       "run scan_dev_for_boot; " \
  86                   "fi; "                        \
  87               "done\0"                          \
  88         "scan_dev_for_boot="                              \
  89                 "echo Scanning ${devtype} "               \
  90                                 "${devnum}:${distro_bootpart}...; "  \
  91                 "for prefix in ${boot_prefixes}; do "     \
  92                         "run scan_dev_for_scripts; "      \
  93                 "done;"                                   \
  94                 "\0"                                      \
  95         "installer=load mmc 0:2 $load_addr "    \
  96                    "/flex_installer_arm64.itb; "        \
  97                    "bootm $load_addr#$board\0"  \
  98         "qspi_bootcmd=echo Trying load from qspi..;"    \
  99                 "sf probe && sf read $load_addr "       \
 100                 "$kernel_addr $kernel_size && bootm $load_addr#$board\0"
 101
 102 #undef CONFIG_BOOTCOMMAND
 103 #define CONFIG_BOOTCOMMAND "run distro_bootcmd;run qspi_bootcmd"
 104
 105 #include <asm/fsl_secure_boot.h>
 106
 107 #endif /* __LS1012ARDB_H__ */