include/configs/MPC8569MDS.h

   1 /*
   2  * Copyright 2009-2011 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 /*
   8  * mpc8569mds board configuration file
   9  */
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #define CONFIG_SYS_SRIO
  14 #define CONFIG_SRIO1                    /* SRIO port 1 */
  15
  16 #define CONFIG_PCIE1            1       /* PCIE controller */
  17 #define CONFIG_FSL_PCI_INIT     1       /* use common fsl pci init code */
  18 #define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
  19 #define CONFIG_FSL_PCIE_RESET   1       /* need PCIe reset errata */
  20 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  21 #define CONFIG_QE                       /* Enable QE */
  22 #define CONFIG_ENV_OVERWRITE
  23
  24 #ifndef __ASSEMBLY__
  25 extern unsigned long get_clock_freq(void);
  26 #endif
  27 /* Replace a call to get_clock_freq (after it is implemented)*/
  28 #define CONFIG_SYS_CLK_FREQ     66666666
  29 #define CONFIG_DDR_CLK_FREQ     CONFIG_SYS_CLK_FREQ
  30
  31 #ifdef CONFIG_ATM
  32 #define CONFIG_PQ_MDS_PIB
  33 #define CONFIG_PQ_MDS_PIB_ATM
  34 #endif
  35
  36 /*
  37  * These can be toggled for performance analysis, otherwise use default.
  38  */
  39 #define CONFIG_L2_CACHE                         /* toggle L2 cache      */
  40 #define CONFIG_BTB                              /* toggle branch predition */
  41
  42 #ifndef CONFIG_SYS_MONITOR_BASE
  43 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  44 #endif
  45
  46 /*
  47  * Only possible on E500 Version 2 or newer cores.
  48  */
  49 #define CONFIG_ENABLE_36BIT_PHYS        1
  50
  51 #define CONFIG_BOARD_EARLY_INIT_R       1
  52 #define CONFIG_HWCONFIG
  53
  54 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
  55 #define CONFIG_SYS_MEMTEST_END          0x00400000
  56
  57 /*
  58  * Config the L2 Cache as L2 SRAM
  59  */
  60 #define CONFIG_SYS_INIT_L2_ADDR         0xf8f80000
  61 #define CONFIG_SYS_INIT_L2_ADDR_PHYS    CONFIG_SYS_INIT_L2_ADDR
  62 #define CONFIG_SYS_L2_SIZE              (512 << 10)
  63 #define CONFIG_SYS_INIT_L2_END  (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
  64
  65 #define CONFIG_SYS_CCSRBAR              0xe0000000
  66 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  67
  68 #if defined(CONFIG_NAND_SPL)
  69 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
  70 #endif
  71
  72 /* DDR Setup */
  73 #undef CONFIG_FSL_DDR_INTERACTIVE
  74 #define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup*/
  75 #define CONFIG_DDR_SPD
  76 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
  77
  78 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
  79
  80 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  81                                         /* DDR is system memory*/
  82 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  83
  84 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  85 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
  86
  87 /* I2C addresses of SPD EEPROMs */
  88 #define SPD_EEPROM_ADDRESS    0x51    /* CTLR 0 DIMM 0 */
  89
  90 /* These are used when DDR doesn't use SPD.  */
  91 #define CONFIG_SYS_SDRAM_SIZE           1024            /* DDR is 1024MB */
  92 #define CONFIG_SYS_DDR_CS0_BNDS         0x0000003F
  93 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80014202
  94 #define CONFIG_SYS_DDR_TIMING_3         0x00020000
  95 #define CONFIG_SYS_DDR_TIMING_0         0x00330004
  96 #define CONFIG_SYS_DDR_TIMING_1         0x6F6B4644
  97 #define CONFIG_SYS_DDR_TIMING_2         0x002888D0
  98 #define CONFIG_SYS_DDR_SDRAM_CFG        0x47000000
  99 #define CONFIG_SYS_DDR_SDRAM_CFG_2      0x04401040
 100 #define CONFIG_SYS_DDR_SDRAM_MODE       0x40401521
 101 #define CONFIG_SYS_DDR_SDRAM_MODE_2     0x8000C000
 102 #define CONFIG_SYS_DDR_SDRAM_INTERVAL   0x03E00000
 103 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 104 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   0x01000000
 105 #define CONFIG_SYS_DDR_TIMING_4         0x00220001
 106 #define CONFIG_SYS_DDR_TIMING_5         0x03402400
 107 #define CONFIG_SYS_DDR_ZQ_CNTL          0x89080600
 108 #define CONFIG_SYS_DDR_WRLVL_CNTL       0x0655A604
 109 #define CONFIG_SYS_DDR_CDR_1            0x80040000
 110 #define CONFIG_SYS_DDR_CDR_2            0x00000000
 111 #define CONFIG_SYS_DDR_OCD_CTRL         0x00000000
 112 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 113 #define CONFIG_SYS_DDR_CONTROL          0xc7000000      /* Type = DDR3 */
 114 #define CONFIG_SYS_DDR_CONTROL2         0x24400000
 115
 116 #define CONFIG_SYS_DDR_ERR_INT_EN       0x0000000d
 117 #define CONFIG_SYS_DDR_ERR_DIS          0x00000000
 118 #define CONFIG_SYS_DDR_SBE              0x00010000
 119
 120 #undef CONFIG_CLOCKS_IN_MHZ
 121
 122 /*
 123  * Local Bus Definitions
 124  */
 125
 126 #define CONFIG_SYS_FLASH_BASE           0xfe000000      /* start of FLASH 32M */
 127 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 128
 129 #define CONFIG_SYS_BCSR_BASE            0xf8000000
 130 #define CONFIG_SYS_BCSR_BASE_PHYS       CONFIG_SYS_BCSR_BASE
 131
 132 /*Chip select 0 - Flash*/
 133 #define CONFIG_FLASH_BR_PRELIM          0xfe000801
 134 #define CONFIG_FLASH_OR_PRELIM          0xfe000ff7
 135
 136 /*Chip select 1 - BCSR*/
 137 #define CONFIG_SYS_BR1_PRELIM           0xf8000801
 138 #define CONFIG_SYS_OR1_PRELIM           0xffffe9f7
 139
 140 /*Chip select 4 - PIB*/
 141 #define CONFIG_SYS_BR4_PRELIM           0xf8008801
 142 #define CONFIG_SYS_OR4_PRELIM           0xffffe9f7
 143
 144 /*Chip select 5 - PIB*/
 145 #define CONFIG_SYS_BR5_PRELIM           0xf8010801
 146 #define CONFIG_SYS_OR5_PRELIM           0xffffe9f7
 147
 148 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 149 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* sectors per device */
 150 #undef  CONFIG_SYS_FLASH_CHECKSUM
 151 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 152 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 153
 154 #undef CONFIG_SYS_RAMBOOT
 155
 156 #define CONFIG_FLASH_CFI_DRIVER
 157 #define CONFIG_SYS_FLASH_CFI
 158 #define CONFIG_SYS_FLASH_EMPTY_INFO
 159
 160 /* Chip select 3 - NAND */
 161 #ifndef CONFIG_NAND_SPL
 162 #define CONFIG_SYS_NAND_BASE            0xFC000000
 163 #else
 164 #define CONFIG_SYS_NAND_BASE            0xFFF00000
 165 #endif
 166
 167 /* NAND boot: 4K NAND loader config */
 168 #define CONFIG_SYS_NAND_SPL_SIZE        0x1000
 169 #define CONFIG_SYS_NAND_U_BOOT_SIZE     ((512 << 10) - 0x2000)
 170 #define CONFIG_SYS_NAND_U_BOOT_DST      (CONFIG_SYS_INIT_L2_ADDR)
 171 #define CONFIG_SYS_NAND_U_BOOT_START \
 172         (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
 173 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (0)
 174 #define CONFIG_SYS_NAND_U_BOOT_RELOC    (CONFIG_SYS_INIT_L2_END - 0x2000)
 175 #define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)
 176
 177 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 178 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE, }
 179 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 180 #define CONFIG_NAND_FSL_ELBC            1
 181 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 182 #define CONFIG_SYS_NAND_BR_PRELIM       (CONFIG_SYS_NAND_BASE_PHYS \
 183                                 | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \
 184                                 | BR_PS_8            /* Port Size = 8 bit */ \
 185                                 | BR_MS_FCM          /* MSEL = FCM */ \
 186                                 | BR_V)              /* valid */
 187 #define CONFIG_SYS_NAND_OR_PRELIM       (0xFFFC0000          /* length 256K */ \
 188                                 | OR_FCM_CSCT \
 189                                 | OR_FCM_CST \
 190                                 | OR_FCM_CHT \
 191                                 | OR_FCM_SCY_1 \
 192                                 | OR_FCM_TRLX \
 193                                 | OR_FCM_EHTR)
 194
 195 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 196 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 197 #define CONFIG_SYS_BR3_PRELIM   CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 198 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 199
 200 #define CONFIG_SYS_LBC_LCRR     0x00000004      /* LB clock ratio reg */
 201 #define CONFIG_SYS_LBC_LBCR     0x00040000      /* LB config reg */
 202 #define CONFIG_SYS_LBC_LSRT     0x20000000      /* LB sdram refresh timer */
 203 #define CONFIG_SYS_LBC_MRTPR    0x00000000      /* LB refresh timer prescal*/
 204
 205 #define CONFIG_SYS_INIT_RAM_LOCK        1
 206 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000  /* Initial RAM address */
 207 #define CONFIG_SYS_INIT_RAM_SIZE        0x4000      /* Size of used area in RAM */
 208
 209 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 210                         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 211 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 212
 213 #define CONFIG_SYS_MONITOR_LEN  (256 * 1024)    /* Reserve 256 kB for Mon */
 214 #define CONFIG_SYS_MALLOC_LEN   (512 * 1024)    /* Reserved for malloc */
 215
 216 /* Serial Port */
 217 #define CONFIG_SYS_NS16550_SERIAL
 218 #define CONFIG_SYS_NS16550_REG_SIZE    1
 219 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 220 #ifdef CONFIG_NAND_SPL
 221 #define CONFIG_NS16550_MIN_FUNCTIONS
 222 #endif
 223
 224 #define CONFIG_SYS_BAUDRATE_TABLE  \
 225         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 226
 227 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_CCSRBAR+0x4500)
 228 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_CCSRBAR+0x4600)
 229
 230 /*
 231  * I2C
 232  */
 233 #define CONFIG_SYS_I2C
 234 #define CONFIG_SYS_I2C_FSL
 235 #define CONFIG_SYS_FSL_I2C_SPEED        400000
 236 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 237 #define CONFIG_SYS_FSL_I2C2_SPEED       400000
 238 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 239 #define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 240 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 241 #define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 242
 243 /*
 244  * I2C2 EEPROM
 245  */
 246 #define CONFIG_ID_EEPROM
 247 #ifdef CONFIG_ID_EEPROM
 248 #define CONFIG_SYS_I2C_EEPROM_NXID
 249 #endif
 250 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x52
 251 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 252 #define CONFIG_SYS_EEPROM_BUS_NUM       1
 253
 254 #define PLPPAR1_I2C_BIT_MASK            0x0000000F
 255 #define PLPPAR1_I2C2_VAL                0x00000000
 256 #define PLPPAR1_ESDHC_VAL               0x0000000A
 257 #define PLPDIR1_I2C_BIT_MASK            0x0000000F
 258 #define PLPDIR1_I2C2_VAL                0x0000000F
 259 #define PLPDIR1_ESDHC_VAL               0x00000006
 260 #define PLPPAR1_UART0_BIT_MASK          0x00000fc0
 261 #define PLPPAR1_ESDHC_4BITS_VAL         0x00000a80
 262 #define PLPDIR1_UART0_BIT_MASK          0x00000fc0
 263 #define PLPDIR1_ESDHC_4BITS_VAL         0x00000a80
 264
 265 /*
 266  * General PCI
 267  * Memory Addresses are mapped 1-1. I/O is mapped from 0
 268  */
 269 #define CONFIG_SYS_PCIE1_NAME           "Slot"
 270 #define CONFIG_SYS_PCIE1_MEM_VIRT       0xa0000000
 271 #define CONFIG_SYS_PCIE1_MEM_BUS        0xa0000000
 272 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xa0000000
 273 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 274 #define CONFIG_SYS_PCIE1_IO_VIRT        0xe2800000
 275 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 276 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe2800000
 277 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00800000      /* 8M */
 278
 279 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xC0000000
 280 #define CONFIG_SYS_SRIO1_MEM_BUS        0xC0000000
 281 #define CONFIG_SYS_SRIO1_MEM_PHYS       CONFIG_SYS_SRIO1_MEM_BUS
 282 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x20000000      /* 512M */
 283
 284 #ifdef CONFIG_QE
 285 /*
 286  * QE UEC ethernet configuration
 287  */
 288 #define CONFIG_SYS_UCC_RGMII_MODE       /* Set UCC work at RGMII by default */
 289 #undef CONFIG_SYS_UCC_RMII_MODE         /* Set UCC work at RMII mode */
 290
 291 #define CONFIG_MIIM_ADDRESS     (CONFIG_SYS_CCSRBAR + 0x82120)
 292 #define CONFIG_UEC_ETH
 293 #define CONFIG_ETHPRIME         "UEC0"
 294 #define CONFIG_PHY_MODE_NEED_CHANGE
 295
 296 #define CONFIG_UEC_ETH1         /* GETH1 */
 297 #define CONFIG_HAS_ETH0
 298
 299 #ifdef CONFIG_UEC_ETH1
 300 #define CONFIG_SYS_UEC1_UCC_NUM        0       /* UCC1 */
 301 #define CONFIG_SYS_UEC1_RX_CLK         QE_CLK_NONE
 302 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 303 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK12
 304 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 305 #define CONFIG_SYS_UEC1_PHY_ADDR       7
 306 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 307 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 308 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 309 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16 /* CLK16 for RMII */
 310 #define CONFIG_SYS_UEC1_ETH_TYPE       FAST_ETH
 311 #define CONFIG_SYS_UEC1_PHY_ADDR       8        /* 0x8 for RMII */
 312 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 313 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
 314 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 315 #endif /* CONFIG_UEC_ETH1 */
 316
 317 #define CONFIG_UEC_ETH2         /* GETH2 */
 318 #define CONFIG_HAS_ETH1
 319
 320 #ifdef CONFIG_UEC_ETH2
 321 #define CONFIG_SYS_UEC2_UCC_NUM        1       /* UCC2 */
 322 #define CONFIG_SYS_UEC2_RX_CLK         QE_CLK_NONE
 323 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 324 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK17
 325 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 326 #define CONFIG_SYS_UEC2_PHY_ADDR       1
 327 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 328 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 329 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 330 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16 /* CLK 16 for RMII */
 331 #define CONFIG_SYS_UEC2_ETH_TYPE       FAST_ETH
 332 #define CONFIG_SYS_UEC2_PHY_ADDR       0x9      /* 0x9 for RMII */
 333 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 334 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
 335 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 336 #endif /* CONFIG_UEC_ETH2 */
 337
 338 #define CONFIG_UEC_ETH3         /* GETH3 */
 339 #define CONFIG_HAS_ETH2
 340
 341 #ifdef CONFIG_UEC_ETH3
 342 #define CONFIG_SYS_UEC3_UCC_NUM        2       /* UCC3 */
 343 #define CONFIG_SYS_UEC3_RX_CLK         QE_CLK_NONE
 344 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 345 #define CONFIG_SYS_UEC3_TX_CLK         QE_CLK12
 346 #define CONFIG_SYS_UEC3_ETH_TYPE       GIGA_ETH
 347 #define CONFIG_SYS_UEC3_PHY_ADDR       2
 348 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 349 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 1000
 350 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 351 #define CONFIG_SYS_UEC3_TX_CLK          QE_CLK16 /* CLK_16 for RMII */
 352 #define CONFIG_SYS_UEC3_ETH_TYPE        FAST_ETH
 353 #define CONFIG_SYS_UEC3_PHY_ADDR        0xA     /* 0xA for RMII */
 354 #define CONFIG_SYS_UEC3_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 355 #define CONFIG_SYS_UEC3_INTERFACE_SPEED 100
 356 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 357 #endif /* CONFIG_UEC_ETH3 */
 358
 359 #define CONFIG_UEC_ETH4         /* GETH4 */
 360 #define CONFIG_HAS_ETH3
 361
 362 #ifdef CONFIG_UEC_ETH4
 363 #define CONFIG_SYS_UEC4_UCC_NUM        3       /* UCC4 */
 364 #define CONFIG_SYS_UEC4_RX_CLK         QE_CLK_NONE
 365 #if defined(CONFIG_SYS_UCC_RGMII_MODE)
 366 #define CONFIG_SYS_UEC4_TX_CLK         QE_CLK17
 367 #define CONFIG_SYS_UEC4_ETH_TYPE       GIGA_ETH
 368 #define CONFIG_SYS_UEC4_PHY_ADDR       3
 369 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 370 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 1000
 371 #elif defined(CONFIG_SYS_UCC_RMII_MODE)
 372 #define CONFIG_SYS_UEC4_TX_CLK          QE_CLK16 /* CLK16 for RMII */
 373 #define CONFIG_SYS_UEC4_ETH_TYPE        FAST_ETH
 374 #define CONFIG_SYS_UEC4_PHY_ADDR        0xB     /* 0xB for RMII */
 375 #define CONFIG_SYS_UEC4_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
 376 #define CONFIG_SYS_UEC4_INTERFACE_SPEED 100
 377 #endif /* CONFIG_SYS_UCC_RGMII_MODE */
 378 #endif /* CONFIG_UEC_ETH4 */
 379
 380 #undef CONFIG_UEC_ETH6         /* GETH6 */
 381 #define CONFIG_HAS_ETH5
 382
 383 #ifdef CONFIG_UEC_ETH6
 384 #define CONFIG_SYS_UEC6_UCC_NUM        5       /* UCC6 */
 385 #define CONFIG_SYS_UEC6_RX_CLK         QE_CLK_NONE
 386 #define CONFIG_SYS_UEC6_TX_CLK         QE_CLK_NONE
 387 #define CONFIG_SYS_UEC6_ETH_TYPE       GIGA_ETH
 388 #define CONFIG_SYS_UEC6_PHY_ADDR       4
 389 #define CONFIG_SYS_UEC6_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 390 #define CONFIG_SYS_UEC6_INTERFACE_SPEED 1000
 391 #endif /* CONFIG_UEC_ETH6 */
 392
 393 #undef CONFIG_UEC_ETH8         /* GETH8 */
 394 #define CONFIG_HAS_ETH7
 395
 396 #ifdef CONFIG_UEC_ETH8
 397 #define CONFIG_SYS_UEC8_UCC_NUM        7       /* UCC8 */
 398 #define CONFIG_SYS_UEC8_RX_CLK         QE_CLK_NONE
 399 #define CONFIG_SYS_UEC8_TX_CLK         QE_CLK_NONE
 400 #define CONFIG_SYS_UEC8_ETH_TYPE       GIGA_ETH
 401 #define CONFIG_SYS_UEC8_PHY_ADDR       6
 402 #define CONFIG_SYS_UEC8_INTERFACE_TYPE PHY_INTERFACE_MODE_SGMII
 403 #define CONFIG_SYS_UEC8_INTERFACE_SPEED 1000
 404 #endif /* CONFIG_UEC_ETH8 */
 405
 406 #endif /* CONFIG_QE */
 407
 408 #if defined(CONFIG_PCI)
 409 #undef CONFIG_EEPRO100
 410 #undef CONFIG_TULIP
 411
 412 #undef CONFIG_PCI_SCAN_SHOW             /* show pci devices on startup */
 413
 414 #endif  /* CONFIG_PCI */
 415
 416 /*
 417  * Environment
 418  */
 419 #if defined(CONFIG_SYS_RAMBOOT)
 420 #else
 421 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 422 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 423 #define CONFIG_ENV_SIZE         0x2000
 424 #endif
 425
 426 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 427 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 428
 429 /* QE microcode/firmware address */
 430 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 431 #define CONFIG_SYS_QE_FW_ADDR   0xfff00000
 432
 433 /*
 434  * BOOTP options
 435  */
 436 #define CONFIG_BOOTP_BOOTFILESIZE
 437
 438 #undef CONFIG_WATCHDOG                  /* watchdog disabled */
 439
 440 #ifdef CONFIG_MMC
 441 #define CONFIG_FSL_ESDHC
 442 #define CONFIG_FSL_ESDHC_PIN_MUX
 443 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 444 #endif
 445
 446 /*
 447  * Miscellaneous configurable options
 448  */
 449 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 450 #if defined(CONFIG_CMD_KGDB)
 451 #define CONFIG_SYS_CBSIZE       2048            /* Console I/O Buffer Size */
 452 #else
 453 #define CONFIG_SYS_CBSIZE       512             /* Console I/O Buffer Size */
 454 #endif
 455 #define CONFIG_SYS_MAXARGS      32              /* max number of command args */
 456 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 457                                                 /* Boot Argument Buffer Size */
 458
 459 /*
 460  * For booting Linux, the board info and command line data
 461  * have to be in the first 64 MB of memory, since this is
 462  * the maximum mapped by the Linux kernel during initialization.
 463  */
 464 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux*/
 465 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 466
 467 #if defined(CONFIG_CMD_KGDB)
 468 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 469 #endif
 470
 471 /*
 472  * Environment Configuration
 473  */
 474 #define CONFIG_HOSTNAME mpc8569mds
 475 #define CONFIG_ROOTPATH  "/nfsroot"
 476 #define CONFIG_BOOTFILE  "your.uImage"
 477
 478 #define CONFIG_SERVERIP  192.168.1.1
 479 #define CONFIG_GATEWAYIP 192.168.1.1
 480 #define CONFIG_NETMASK   255.255.255.0
 481
 482 #define CONFIG_LOADADDR  200000   /*default location for tftp and bootm*/
 483
 484 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 485         "netdev=eth0\0"                                                 \
 486         "consoledev=ttyS0\0"                                            \
 487         "ramdiskaddr=600000\0"                                          \
 488         "ramdiskfile=your.ramdisk.u-boot\0"                             \
 489         "fdtaddr=400000\0"                                              \
 490         "fdtfile=your.fdt.dtb\0"                                        \
 491         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 492         "nfsroot=$serverip:$rootpath "                                  \
 493         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 494         "console=$consoledev,$baudrate $othbootargs\0"                  \
 495         "ramargs=setenv bootargs root=/dev/ram rw "                     \
 496         "console=$consoledev,$baudrate $othbootargs\0"                  \
 497
 498 #define CONFIG_NFSBOOTCOMMAND                                           \
 499         "run nfsargs;"                                                  \
 500         "tftp $loadaddr $bootfile;"                                     \
 501         "tftp $fdtaddr $fdtfile;"                                       \
 502         "bootm $loadaddr - $fdtaddr"
 503
 504 #define CONFIG_RAMBOOTCOMMAND                                           \
 505         "run ramargs;"                                                  \
 506         "tftp $ramdiskaddr $ramdiskfile;"                               \
 507         "tftp $loadaddr $bootfile;"                                     \
 508         "bootm $loadaddr $ramdiskaddr"
 509
 510 #define CONFIG_BOOTCOMMAND  CONFIG_NFSBOOTCOMMAND
 511
 512 #endif  /* __CONFIG_H */