drivers/usb/host/xhci-ring.c

   1 /*
   2  * xHCI host controller driver
   3  *
   4  * Copyright (C) 2008 Intel Corp.
   5  *
   6  * Author: Sarah Sharp
   7  * Some code borrowed from the Linux EHCI driver.
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  *
  13  * This program is distributed in the hope that it will be useful, but
  14  * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
  15  * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
  16  * for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software Foundation,
  20  * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21  */
  22
  23 /*
  24  * Ring initialization rules:
  25  * 1. Each segment is initialized to zero, except for link TRBs.
  26  * 2. Ring cycle state = 0.  This represents Producer Cycle State (PCS) or
  27  *    Consumer Cycle State (CCS), depending on ring function.
  28  * 3. Enqueue pointer = dequeue pointer = address of first TRB in the segment.
  29  *
  30  * Ring behavior rules:
  31  * 1. A ring is empty if enqueue == dequeue.  This means there will always be at
  32  *    least one free TRB in the ring.  This is useful if you want to turn that
  33  *    into a link TRB and expand the ring.
  34  * 2. When incrementing an enqueue or dequeue pointer, if the next TRB is a
  35  *    link TRB, then load the pointer with the address in the link TRB.  If the
  36  *    link TRB had its toggle bit set, you may need to update the ring cycle
  37  *    state (see cycle bit rules).  You may have to do this multiple times
  38  *    until you reach a non-link TRB.
  39  * 3. A ring is full if enqueue++ (for the definition of increment above)
  40  *    equals the dequeue pointer.
  41  *
  42  * Cycle bit rules:
  43  * 1. When a consumer increments a dequeue pointer and encounters a toggle bit
  44  *    in a link TRB, it must toggle the ring cycle state.
  45  * 2. When a producer increments an enqueue pointer and encounters a toggle bit
  46  *    in a link TRB, it must toggle the ring cycle state.
  47  *
  48  * Producer rules:
  49  * 1. Check if ring is full before you enqueue.
  50  * 2. Write the ring cycle state to the cycle bit in the TRB you're enqueuing.
  51  *    Update enqueue pointer between each write (which may update the ring
  52  *    cycle state).
  53  * 3. Notify consumer.  If SW is producer, it rings the doorbell for command
  54  *    and endpoint rings.  If HC is the producer for the event ring,
  55  *    and it generates an interrupt according to interrupt modulation rules.
  56  *
  57  * Consumer rules:
  58  * 1. Check if TRB belongs to you.  If the cycle bit == your ring cycle state,
  59  *    the TRB is owned by the consumer.
  60  * 2. Update dequeue pointer (which may update the ring cycle state) and
  61  *    continue processing TRBs until you reach a TRB which is not owned by you.
  62  * 3. Notify the producer.  SW is the consumer for the event ring, and it
  63  *   updates event ring dequeue pointer.  HC is the consumer for the command and
  64  *   endpoint rings; it generates events on the event ring for these.
  65  */
  66
  67 #include <linux/scatterlist.h>
  68 #include "xhci.h"
  69
  70 /*
  71  * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
  72  * address of the TRB.
  73  */
  74 dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg,
  75                 union xhci_trb *trb)
  76 {
  77         unsigned long segment_offset;
  78
  79         if (!seg || !trb || trb < seg->trbs)
  80                 return 0;
  81         /* offset in TRBs */
  82         segment_offset = trb - seg->trbs;
  83         if (segment_offset > TRBS_PER_SEGMENT)
  84                 return 0;
  85         return seg->dma + (segment_offset * sizeof(*trb));
  86 }
  87
  88 /* Does this link TRB point to the first segment in a ring,
  89  * or was the previous TRB the last TRB on the last segment in the ERST?
  90  */
  91 static inline bool last_trb_on_last_seg(struct xhci_hcd *xhci, struct xhci_ring *ring,
  92                 struct xhci_segment *seg, union xhci_trb *trb)
  93 {
  94         if (ring == xhci->event_ring)
  95                 return (trb == &seg->trbs[TRBS_PER_SEGMENT]) &&
  96                         (seg->next == xhci->event_ring->first_seg);
  97         else
  98                 return trb->link.control & LINK_TOGGLE;
  99 }
 100
 101 /* Is this TRB a link TRB or was the last TRB the last TRB in this event ring
 102  * segment?  I.e. would the updated event TRB pointer step off the end of the
 103  * event seg?
 104  */
 105 static inline int last_trb(struct xhci_hcd *xhci, struct xhci_ring *ring,
 106                 struct xhci_segment *seg, union xhci_trb *trb)
 107 {
 108         if (ring == xhci->event_ring)
 109                 return trb == &seg->trbs[TRBS_PER_SEGMENT];
 110         else
 111                 return (trb->link.control & TRB_TYPE_BITMASK) == TRB_TYPE(TRB_LINK);
 112 }
 113
 114 /* Updates trb to point to the next TRB in the ring, and updates seg if the next
 115  * TRB is in a new segment.  This does not skip over link TRBs, and it does not
 116  * effect the ring dequeue or enqueue pointers.
 117  */
 118 static void next_trb(struct xhci_hcd *xhci,
 119                 struct xhci_ring *ring,
 120                 struct xhci_segment **seg,
 121                 union xhci_trb **trb)
 122 {
 123         if (last_trb(xhci, ring, *seg, *trb)) {
 124                 *seg = (*seg)->next;
 125                 *trb = ((*seg)->trbs);
 126         } else {
 127                 *trb = (*trb)++;
 128         }
 129 }
 130
 131 /*
 132  * See Cycle bit rules. SW is the consumer for the event ring only.
 133  * Don't make a ring full of link TRBs.  That would be dumb and this would loop.
 134  */
 135 static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer)
 136 {
 137         union xhci_trb *next = ++(ring->dequeue);
 138         unsigned long long addr;
 139
 140         ring->deq_updates++;
 141         /* Update the dequeue pointer further if that was a link TRB or we're at
 142          * the end of an event ring segment (which doesn't have link TRBS)
 143          */
 144         while (last_trb(xhci, ring, ring->deq_seg, next)) {
 145                 if (consumer && last_trb_on_last_seg(xhci, ring, ring->deq_seg, next)) {
 146                         ring->cycle_state = (ring->cycle_state ? 0 : 1);
 147                         if (!in_interrupt())
 148                                 xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n",
 149                                                 ring,
 150                                                 (unsigned int) ring->cycle_state);
 151                 }
 152                 ring->deq_seg = ring->deq_seg->next;
 153                 ring->dequeue = ring->deq_seg->trbs;
 154                 next = ring->dequeue;
 155         }
 156         addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue);
 157         if (ring == xhci->event_ring)
 158                 xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr);
 159         else if (ring == xhci->cmd_ring)
 160                 xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr);
 161         else
 162                 xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr);
 163 }
 164
 165 /*
 166  * See Cycle bit rules. SW is the consumer for the event ring only.
 167  * Don't make a ring full of link TRBs.  That would be dumb and this would loop.
 168  *
 169  * If we've just enqueued a TRB that is in the middle of a TD (meaning the
 170  * chain bit is set), then set the chain bit in all the following link TRBs.
 171  * If we've enqueued the last TRB in a TD, make sure the following link TRBs
 172  * have their chain bit cleared (so that each Link TRB is a separate TD).
 173  *
 174  * Section 6.4.4.1 of the 0.95 spec says link TRBs cannot have the chain bit
 175  * set, but other sections talk about dealing with the chain bit set.  This was
 176  * fixed in the 0.96 specification errata, but we have to assume that all 0.95
 177  * xHCI hardware can't handle the chain bit being cleared on a link TRB.
 178  */
 179 static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer)
 180 {
 181         u32 chain;
 182         union xhci_trb *next;
 183         unsigned long long addr;
 184
 185         chain = ring->enqueue->generic.field[3] & TRB_CHAIN;
 186         next = ++(ring->enqueue);
 187
 188         ring->enq_updates++;
 189         /* Update the dequeue pointer further if that was a link TRB or we're at
 190          * the end of an event ring segment (which doesn't have link TRBS)
 191          */
 192         while (last_trb(xhci, ring, ring->enq_seg, next)) {
 193                 if (!consumer) {
 194                         if (ring != xhci->event_ring) {
 195                                 /* If we're not dealing with 0.95 hardware,
 196                                  * carry over the chain bit of the previous TRB
 197                                  * (which may mean the chain bit is cleared).
 198                                  */
 199                                 if (!xhci_link_trb_quirk(xhci)) {
 200                                         next->link.control &= ~TRB_CHAIN;
 201                                         next->link.control |= chain;
 202                                 }
 203                                 /* Give this link TRB to the hardware */
 204                                 wmb();
 205                                 if (next->link.control & TRB_CYCLE)
 206                                         next->link.control &= (u32) ~TRB_CYCLE;
 207                                 else
 208                                         next->link.control |= (u32) TRB_CYCLE;
 209                         }
 210                         /* Toggle the cycle bit after the last ring segment. */
 211                         if (last_trb_on_last_seg(xhci, ring, ring->enq_seg, next)) {
 212                                 ring->cycle_state = (ring->cycle_state ? 0 : 1);
 213                                 if (!in_interrupt())
 214                                         xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n",
 215                                                         ring,
 216                                                         (unsigned int) ring->cycle_state);
 217                         }
 218                 }
 219                 ring->enq_seg = ring->enq_seg->next;
 220                 ring->enqueue = ring->enq_seg->trbs;
 221                 next = ring->enqueue;
 222         }
 223         addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue);
 224         if (ring == xhci->event_ring)
 225                 xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr);
 226         else if (ring == xhci->cmd_ring)
 227                 xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr);
 228         else
 229                 xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr);
 230 }
 231
 232 /*
 233  * Check to see if there's room to enqueue num_trbs on the ring.  See rules
 234  * above.
 235  * FIXME: this would be simpler and faster if we just kept track of the number
 236  * of free TRBs in a ring.
 237  */
 238 static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring,
 239                 unsigned int num_trbs)
 240 {
 241         int i;
 242         union xhci_trb *enq = ring->enqueue;
 243         struct xhci_segment *enq_seg = ring->enq_seg;
 244
 245         /* Check if ring is empty */
 246         if (enq == ring->dequeue)
 247                 return 1;
 248         /* Make sure there's an extra empty TRB available */
 249         for (i = 0; i <= num_trbs; ++i) {
 250                 if (enq == ring->dequeue)
 251                         return 0;
 252                 enq++;
 253                 while (last_trb(xhci, ring, enq_seg, enq)) {
 254                         enq_seg = enq_seg->next;
 255                         enq = enq_seg->trbs;
 256                 }
 257         }
 258         return 1;
 259 }
 260
 261 void xhci_set_hc_event_deq(struct xhci_hcd *xhci)
 262 {
 263         u64 temp;
 264         dma_addr_t deq;
 265
 266         deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg,
 267                         xhci->event_ring->dequeue);
 268         if (deq == 0 && !in_interrupt())
 269                 xhci_warn(xhci, "WARN something wrong with SW event ring "
 270                                 "dequeue ptr.\n");
 271         /* Update HC event ring dequeue pointer */
 272         temp = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
 273         temp &= ERST_PTR_MASK;
 274         /* Don't clear the EHB bit (which is RW1C) because
 275          * there might be more events to service.
 276          */
 277         temp &= ~ERST_EHB;
 278         xhci_dbg(xhci, "// Write event ring dequeue pointer, preserving EHB bit\n");
 279         xhci_write_64(xhci, ((u64) deq & (u64) ~ERST_PTR_MASK) | temp,
 280                         &xhci->ir_set->erst_dequeue);
 281 }
 282
 283 /* Ring the host controller doorbell after placing a command on the ring */
 284 void xhci_ring_cmd_db(struct xhci_hcd *xhci)
 285 {
 286         u32 temp;
 287
 288         xhci_dbg(xhci, "// Ding dong!\n");
 289         temp = xhci_readl(xhci, &xhci->dba->doorbell[0]) & DB_MASK;
 290         xhci_writel(xhci, temp | DB_TARGET_HOST, &xhci->dba->doorbell[0]);
 291         /* Flush PCI posted writes */
 292         xhci_readl(xhci, &xhci->dba->doorbell[0]);
 293 }
 294
 295 static void ring_ep_doorbell(struct xhci_hcd *xhci,
 296                 unsigned int slot_id,
 297                 unsigned int ep_index)
 298 {
 299         struct xhci_virt_ep *ep;
 300         unsigned int ep_state;
 301         u32 field;
 302         __u32 __iomem *db_addr = &xhci->dba->doorbell[slot_id];
 303
 304         ep = &xhci->devs[slot_id]->eps[ep_index];
 305         ep_state = ep->ep_state;
 306         /* Don't ring the doorbell for this endpoint if there are pending
 307          * cancellations because the we don't want to interrupt processing.
 308          */
 309         if (!ep->cancels_pending && !(ep_state & SET_DEQ_PENDING)
 310                         && !(ep_state & EP_HALTED)) {
 311                 field = xhci_readl(xhci, db_addr) & DB_MASK;
 312                 xhci_writel(xhci, field | EPI_TO_DB(ep_index), db_addr);
 313                 /* Flush PCI posted writes - FIXME Matthew Wilcox says this
 314                  * isn't time-critical and we shouldn't make the CPU wait for
 315                  * the flush.
 316                  */
 317                 xhci_readl(xhci, db_addr);
 318         }
 319 }
 320
 321 /*
 322  * Find the segment that trb is in.  Start searching in start_seg.
 323  * If we must move past a segment that has a link TRB with a toggle cycle state
 324  * bit set, then we will toggle the value pointed at by cycle_state.
 325  */
 326 static struct xhci_segment *find_trb_seg(
 327                 struct xhci_segment *start_seg,
 328                 union xhci_trb  *trb, int *cycle_state)
 329 {
 330         struct xhci_segment *cur_seg = start_seg;
 331         struct xhci_generic_trb *generic_trb;
 332
 333         while (cur_seg->trbs > trb ||
 334                         &cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
 335                 generic_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1].generic;
 336                 if (TRB_TYPE(generic_trb->field[3]) == TRB_LINK &&
 337                                 (generic_trb->field[3] & LINK_TOGGLE))
 338                         *cycle_state = ~(*cycle_state) & 0x1;
 339                 cur_seg = cur_seg->next;
 340                 if (cur_seg == start_seg)
 341                         /* Looped over the entire list.  Oops! */
 342                         return 0;
 343         }
 344         return cur_seg;
 345 }
 346
 347 /*
 348  * Move the xHC's endpoint ring dequeue pointer past cur_td.
 349  * Record the new state of the xHC's endpoint ring dequeue segment,
 350  * dequeue pointer, and new consumer cycle state in state.
 351  * Update our internal representation of the ring's dequeue pointer.
 352  *
 353  * We do this in three jumps:
 354  *  - First we update our new ring state to be the same as when the xHC stopped.
 355  *  - Then we traverse the ring to find the segment that contains
 356  *    the last TRB in the TD.  We toggle the xHC's new cycle state when we pass
 357  *    any link TRBs with the toggle cycle bit set.
 358  *  - Finally we move the dequeue state one TRB further, toggling the cycle bit
 359  *    if we've moved it past a link TRB with the toggle cycle bit set.
 360  */
 361 void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
 362                 unsigned int slot_id, unsigned int ep_index,
 363                 struct xhci_td *cur_td, struct xhci_dequeue_state *state)
 364 {
 365         struct xhci_virt_device *dev = xhci->devs[slot_id];
 366         struct xhci_ring *ep_ring = dev->eps[ep_index].ring;
 367         struct xhci_generic_trb *trb;
 368         struct xhci_ep_ctx *ep_ctx;
 369         dma_addr_t addr;
 370
 371         state->new_cycle_state = 0;
 372         xhci_dbg(xhci, "Finding segment containing stopped TRB.\n");
 373         state->new_deq_seg = find_trb_seg(cur_td->start_seg,
 374                         dev->eps[ep_index].stopped_trb,
 375                         &state->new_cycle_state);
 376         if (!state->new_deq_seg)
 377                 BUG();
 378         /* Dig out the cycle state saved by the xHC during the stop ep cmd */
 379         xhci_dbg(xhci, "Finding endpoint context\n");
 380         ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
 381         state->new_cycle_state = 0x1 & ep_ctx->deq;
 382
 383         state->new_deq_ptr = cur_td->last_trb;
 384         xhci_dbg(xhci, "Finding segment containing last TRB in TD.\n");
 385         state->new_deq_seg = find_trb_seg(state->new_deq_seg,
 386                         state->new_deq_ptr,
 387                         &state->new_cycle_state);
 388         if (!state->new_deq_seg)
 389                 BUG();
 390
 391         trb = &state->new_deq_ptr->generic;
 392         if (TRB_TYPE(trb->field[3]) == TRB_LINK &&
 393                                 (trb->field[3] & LINK_TOGGLE))
 394                 state->new_cycle_state = ~(state->new_cycle_state) & 0x1;
 395         next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr);
 396
 397         /* Don't update the ring cycle state for the producer (us). */
 398         xhci_dbg(xhci, "New dequeue segment = %p (virtual)\n",
 399                         state->new_deq_seg);
 400         addr = xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr);
 401         xhci_dbg(xhci, "New dequeue pointer = 0x%llx (DMA)\n",
 402                         (unsigned long long) addr);
 403         xhci_dbg(xhci, "Setting dequeue pointer in internal ring state.\n");
 404         ep_ring->dequeue = state->new_deq_ptr;
 405         ep_ring->deq_seg = state->new_deq_seg;
 406 }
 407
 408 static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
 409                 struct xhci_td *cur_td)
 410 {
 411         struct xhci_segment *cur_seg;
 412         union xhci_trb *cur_trb;
 413
 414         for (cur_seg = cur_td->start_seg, cur_trb = cur_td->first_trb;
 415                         true;
 416                         next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
 417                 if ((cur_trb->generic.field[3] & TRB_TYPE_BITMASK) ==
 418                                 TRB_TYPE(TRB_LINK)) {
 419                         /* Unchain any chained Link TRBs, but
 420                          * leave the pointers intact.
 421                          */
 422                         cur_trb->generic.field[3] &= ~TRB_CHAIN;
 423                         xhci_dbg(xhci, "Cancel (unchain) link TRB\n");
 424                         xhci_dbg(xhci, "Address = %p (0x%llx dma); "
 425                                         "in seg %p (0x%llx dma)\n",
 426                                         cur_trb,
 427                                         (unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb),
 428                                         cur_seg,
 429                                         (unsigned long long)cur_seg->dma);
 430                 } else {
 431                         cur_trb->generic.field[0] = 0;
 432                         cur_trb->generic.field[1] = 0;
 433                         cur_trb->generic.field[2] = 0;
 434                         /* Preserve only the cycle bit of this TRB */
 435                         cur_trb->generic.field[3] &= TRB_CYCLE;
 436                         cur_trb->generic.field[3] |= TRB_TYPE(TRB_TR_NOOP);
 437                         xhci_dbg(xhci, "Cancel TRB %p (0x%llx dma) "
 438                                         "in seg %p (0x%llx dma)\n",
 439                                         cur_trb,
 440                                         (unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb),
 441                                         cur_seg,
 442                                         (unsigned long long)cur_seg->dma);
 443                 }
 444                 if (cur_trb == cur_td->last_trb)
 445                         break;
 446         }
 447 }
 448
 449 static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
 450                 unsigned int ep_index, struct xhci_segment *deq_seg,
 451                 union xhci_trb *deq_ptr, u32 cycle_state);
 452
 453 void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
 454                 unsigned int slot_id, unsigned int ep_index,
 455                 struct xhci_dequeue_state *deq_state)
 456 {
 457         struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index];
 458
 459         xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), "
 460                         "new deq ptr = %p (0x%llx dma), new cycle = %u\n",
 461                         deq_state->new_deq_seg,
 462                         (unsigned long long)deq_state->new_deq_seg->dma,
 463                         deq_state->new_deq_ptr,
 464                         (unsigned long long)xhci_trb_virt_to_dma(deq_state->new_deq_seg, deq_state->new_deq_ptr),
 465                         deq_state->new_cycle_state);
 466         queue_set_tr_deq(xhci, slot_id, ep_index,
 467                         deq_state->new_deq_seg,
 468                         deq_state->new_deq_ptr,
 469                         (u32) deq_state->new_cycle_state);
 470         /* Stop the TD queueing code from ringing the doorbell until
 471          * this command completes.  The HC won't set the dequeue pointer
 472          * if the ring is running, and ringing the doorbell starts the
 473          * ring running.
 474          */
 475         ep->ep_state |= SET_DEQ_PENDING;
 476 }
 477
 478 /*
 479  * When we get a command completion for a Stop Endpoint Command, we need to
 480  * unlink any cancelled TDs from the ring.  There are two ways to do that:
 481  *
 482  *  1. If the HW was in the middle of processing the TD that needs to be
 483  *     cancelled, then we must move the ring's dequeue pointer past the last TRB
 484  *     in the TD with a Set Dequeue Pointer Command.
 485  *  2. Otherwise, we turn all the TRBs in the TD into No-op TRBs (with the chain
 486  *     bit cleared) so that the HW will skip over them.
 487  */
 488 static void handle_stopped_endpoint(struct xhci_hcd *xhci,
 489                 union xhci_trb *trb)
 490 {
 491         unsigned int slot_id;
 492         unsigned int ep_index;
 493         struct xhci_ring *ep_ring;
 494         struct xhci_virt_ep *ep;
 495         struct list_head *entry;
 496         struct xhci_td *cur_td = 0;
 497         struct xhci_td *last_unlinked_td;
 498
 499         struct xhci_dequeue_state deq_state;
 500 #ifdef CONFIG_USB_HCD_STAT
 501         ktime_t stop_time = ktime_get();
 502 #endif
 503
 504         memset(&deq_state, 0, sizeof(deq_state));
 505         slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
 506         ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
 507         ep = &xhci->devs[slot_id]->eps[ep_index];
 508         ep_ring = ep->ring;
 509
 510         if (list_empty(&ep->cancelled_td_list))
 511                 return;
 512
 513         /* Fix up the ep ring first, so HW stops executing cancelled TDs.
 514          * We have the xHCI lock, so nothing can modify this list until we drop
 515          * it.  We're also in the event handler, so we can't get re-interrupted
 516          * if another Stop Endpoint command completes
 517          */
 518         list_for_each(entry, &ep->cancelled_td_list) {
 519                 cur_td = list_entry(entry, struct xhci_td, cancelled_td_list);
 520                 xhci_dbg(xhci, "Cancelling TD starting at %p, 0x%llx (dma).\n",
 521                                 cur_td->first_trb,
 522                                 (unsigned long long)xhci_trb_virt_to_dma(cur_td->start_seg, cur_td->first_trb));
 523                 /*
 524                  * If we stopped on the TD we need to cancel, then we have to
 525                  * move the xHC endpoint ring dequeue pointer past this TD.
 526                  */
 527                 if (cur_td == ep->stopped_td)
 528                         xhci_find_new_dequeue_state(xhci, slot_id, ep_index, cur_td,
 529                                         &deq_state);
 530                 else
 531                         td_to_noop(xhci, ep_ring, cur_td);
 532                 /*
 533                  * The event handler won't see a completion for this TD anymore,
 534                  * so remove it from the endpoint ring's TD list.  Keep it in
 535                  * the cancelled TD list for URB completion later.
 536                  */
 537                 list_del(&cur_td->td_list);
 538                 ep->cancels_pending--;
 539         }
 540         last_unlinked_td = cur_td;
 541
 542         /* If necessary, queue a Set Transfer Ring Dequeue Pointer command */
 543         if (deq_state.new_deq_ptr && deq_state.new_deq_seg) {
 544                 xhci_queue_new_dequeue_state(xhci,
 545                                 slot_id, ep_index, &deq_state);
 546                 xhci_ring_cmd_db(xhci);
 547         } else {
 548                 /* Otherwise just ring the doorbell to restart the ring */
 549                 ring_ep_doorbell(xhci, slot_id, ep_index);
 550         }
 551
 552         /*
 553          * Drop the lock and complete the URBs in the cancelled TD list.
 554          * New TDs to be cancelled might be added to the end of the list before
 555          * we can complete all the URBs for the TDs we already unlinked.
 556          * So stop when we've completed the URB for the last TD we unlinked.
 557          */
 558         do {
 559                 cur_td = list_entry(ep->cancelled_td_list.next,
 560                                 struct xhci_td, cancelled_td_list);
 561                 list_del(&cur_td->cancelled_td_list);
 562
 563                 /* Clean up the cancelled URB */
 564 #ifdef CONFIG_USB_HCD_STAT
 565                 hcd_stat_update(xhci->tp_stat, cur_td->urb->actual_length,
 566                                 ktime_sub(stop_time, cur_td->start_time));
 567 #endif
 568                 cur_td->urb->hcpriv = NULL;
 569                 usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), cur_td->urb);
 570
 571                 xhci_dbg(xhci, "Giveback cancelled URB %p\n", cur_td->urb);
 572                 spin_unlock(&xhci->lock);
 573                 /* Doesn't matter what we pass for status, since the core will
 574                  * just overwrite it (because the URB has been unlinked).
 575                  */
 576                 usb_hcd_giveback_urb(xhci_to_hcd(xhci), cur_td->urb, 0);
 577                 kfree(cur_td);
 578
 579                 spin_lock(&xhci->lock);
 580         } while (cur_td != last_unlinked_td);
 581
 582         /* Return to the event handler with xhci->lock re-acquired */
 583 }
 584
 585 /*
 586  * When we get a completion for a Set Transfer Ring Dequeue Pointer command,
 587  * we need to clear the set deq pending flag in the endpoint ring state, so that
 588  * the TD queueing code can ring the doorbell again.  We also need to ring the
 589  * endpoint doorbell to restart the ring, but only if there aren't more
 590  * cancellations pending.
 591  */
 592 static void handle_set_deq_completion(struct xhci_hcd *xhci,
 593                 struct xhci_event_cmd *event,
 594                 union xhci_trb *trb)
 595 {
 596         unsigned int slot_id;
 597         unsigned int ep_index;
 598         struct xhci_ring *ep_ring;
 599         struct xhci_virt_device *dev;
 600         struct xhci_ep_ctx *ep_ctx;
 601         struct xhci_slot_ctx *slot_ctx;
 602
 603         slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
 604         ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
 605         dev = xhci->devs[slot_id];
 606         ep_ring = dev->eps[ep_index].ring;
 607         ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
 608         slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx);
 609
 610         if (GET_COMP_CODE(event->status) != COMP_SUCCESS) {
 611                 unsigned int ep_state;
 612                 unsigned int slot_state;
 613
 614                 switch (GET_COMP_CODE(event->status)) {
 615                 case COMP_TRB_ERR:
 616                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd invalid because "
 617                                         "of stream ID configuration\n");
 618                         break;
 619                 case COMP_CTX_STATE:
 620                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due "
 621                                         "to incorrect slot or ep state.\n");
 622                         ep_state = ep_ctx->ep_info;
 623                         ep_state &= EP_STATE_MASK;
 624                         slot_state = slot_ctx->dev_state;
 625                         slot_state = GET_SLOT_STATE(slot_state);
 626                         xhci_dbg(xhci, "Slot state = %u, EP state = %u\n",
 627                                         slot_state, ep_state);
 628                         break;
 629                 case COMP_EBADSLT:
 630                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed because "
 631                                         "slot %u was not enabled.\n", slot_id);
 632                         break;
 633                 default:
 634                         xhci_warn(xhci, "WARN Set TR Deq Ptr cmd with unknown "
 635                                         "completion code of %u.\n",
 636                                         GET_COMP_CODE(event->status));
 637                         break;
 638                 }
 639                 /* OK what do we do now?  The endpoint state is hosed, and we
 640                  * should never get to this point if the synchronization between
 641                  * queueing, and endpoint state are correct.  This might happen
 642                  * if the device gets disconnected after we've finished
 643                  * cancelling URBs, which might not be an error...
 644                  */
 645         } else {
 646                 xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n",
 647                                 ep_ctx->deq);
 648         }
 649
 650         dev->eps[ep_index].ep_state &= ~SET_DEQ_PENDING;
 651         ring_ep_doorbell(xhci, slot_id, ep_index);
 652 }
 653
 654 static void handle_reset_ep_completion(struct xhci_hcd *xhci,
 655                 struct xhci_event_cmd *event,
 656                 union xhci_trb *trb)
 657 {
 658         int slot_id;
 659         unsigned int ep_index;
 660         struct xhci_ring *ep_ring;
 661
 662         slot_id = TRB_TO_SLOT_ID(trb->generic.field[3]);
 663         ep_index = TRB_TO_EP_INDEX(trb->generic.field[3]);
 664         ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
 665         /* This command will only fail if the endpoint wasn't halted,
 666          * but we don't care.
 667          */
 668         xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n",
 669                         (unsigned int) GET_COMP_CODE(event->status));
 670
 671         /* HW with the reset endpoint quirk needs to have a configure endpoint
 672          * command complete before the endpoint can be used.  Queue that here
 673          * because the HW can't handle two commands being queued in a row.
 674          */
 675         if (xhci->quirks & XHCI_RESET_EP_QUIRK) {
 676                 xhci_dbg(xhci, "Queueing configure endpoint command\n");
 677                 xhci_queue_configure_endpoint(xhci,
 678                                 xhci->devs[slot_id]->in_ctx->dma, slot_id,
 679                                 false);
 680                 xhci_ring_cmd_db(xhci);
 681         } else {
 682                 /* Clear our internal halted state and restart the ring */
 683                 xhci->devs[slot_id]->eps[ep_index].ep_state &= ~EP_HALTED;
 684                 ring_ep_doorbell(xhci, slot_id, ep_index);
 685         }
 686 }
 687
 688 /* Check to see if a command in the device's command queue matches this one.
 689  * Signal the completion or free the command, and return 1.  Return 0 if the
 690  * completed command isn't at the head of the command list.
 691  */
 692 static int handle_cmd_in_cmd_wait_list(struct xhci_hcd *xhci,
 693                 struct xhci_virt_device *virt_dev,
 694                 struct xhci_event_cmd *event)
 695 {
 696         struct xhci_command *command;
 697
 698         if (list_empty(&virt_dev->cmd_list))
 699                 return 0;
 700
 701         command = list_entry(virt_dev->cmd_list.next,
 702                         struct xhci_command, cmd_list);
 703         if (xhci->cmd_ring->dequeue != command->command_trb)
 704                 return 0;
 705
 706         command->status =
 707                 GET_COMP_CODE(event->status);
 708         list_del(&command->cmd_list);
 709         if (command->completion)
 710                 complete(command->completion);
 711         else
 712                 xhci_free_command(xhci, command);
 713         return 1;
 714 }
 715
 716 static void handle_cmd_completion(struct xhci_hcd *xhci,
 717                 struct xhci_event_cmd *event)
 718 {
 719         int slot_id = TRB_TO_SLOT_ID(event->flags);
 720         u64 cmd_dma;
 721         dma_addr_t cmd_dequeue_dma;
 722         struct xhci_input_control_ctx *ctrl_ctx;
 723         struct xhci_virt_device *virt_dev;
 724         unsigned int ep_index;
 725         struct xhci_ring *ep_ring;
 726         unsigned int ep_state;
 727
 728         cmd_dma = event->cmd_trb;
 729         cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
 730                         xhci->cmd_ring->dequeue);
 731         /* Is the command ring deq ptr out of sync with the deq seg ptr? */
 732         if (cmd_dequeue_dma == 0) {
 733                 xhci->error_bitmask |= 1 << 4;
 734                 return;
 735         }
 736         /* Does the DMA address match our internal dequeue pointer address? */
 737         if (cmd_dma != (u64) cmd_dequeue_dma) {
 738                 xhci->error_bitmask |= 1 << 5;
 739                 return;
 740         }
 741         switch (xhci->cmd_ring->dequeue->generic.field[3] & TRB_TYPE_BITMASK) {
 742         case TRB_TYPE(TRB_ENABLE_SLOT):
 743                 if (GET_COMP_CODE(event->status) == COMP_SUCCESS)
 744                         xhci->slot_id = slot_id;
 745                 else
 746                         xhci->slot_id = 0;
 747                 complete(&xhci->addr_dev);
 748                 break;
 749         case TRB_TYPE(TRB_DISABLE_SLOT):
 750                 if (xhci->devs[slot_id])
 751                         xhci_free_virt_device(xhci, slot_id);
 752                 break;
 753         case TRB_TYPE(TRB_CONFIG_EP):
 754                 virt_dev = xhci->devs[slot_id];
 755                 if (handle_cmd_in_cmd_wait_list(xhci, virt_dev, event))
 756                         break;
 757                 /*
 758                  * Configure endpoint commands can come from the USB core
 759                  * configuration or alt setting changes, or because the HW
 760                  * needed an extra configure endpoint command after a reset
 761                  * endpoint command.  In the latter case, the xHCI driver is
 762                  * not waiting on the configure endpoint command.
 763                  */
 764                 ctrl_ctx = xhci_get_input_control_ctx(xhci,
 765                                 virt_dev->in_ctx);
 766                 /* Input ctx add_flags are the endpoint index plus one */
 767                 ep_index = xhci_last_valid_endpoint(ctrl_ctx->add_flags) - 1;
 768                 ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
 769                 if (!ep_ring) {
 770                         /* This must have been an initial configure endpoint */
 771                         xhci->devs[slot_id]->cmd_status =
 772                                 GET_COMP_CODE(event->status);
 773                         complete(&xhci->devs[slot_id]->cmd_completion);
 774                         break;
 775                 }
 776                 ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
 777                 xhci_dbg(xhci, "Completed config ep cmd - last ep index = %d, "
 778                                 "state = %d\n", ep_index, ep_state);
 779                 if (xhci->quirks & XHCI_RESET_EP_QUIRK &&
 780                                 ep_state & EP_HALTED) {
 781                         /* Clear our internal halted state and restart ring */
 782                         xhci->devs[slot_id]->eps[ep_index].ep_state &=
 783                                 ~EP_HALTED;
 784                         ring_ep_doorbell(xhci, slot_id, ep_index);
 785                 } else {
 786                         xhci->devs[slot_id]->cmd_status =
 787                                 GET_COMP_CODE(event->status);
 788                         complete(&xhci->devs[slot_id]->cmd_completion);
 789                 }
 790                 break;
 791         case TRB_TYPE(TRB_EVAL_CONTEXT):
 792                 xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(event->status);
 793                 complete(&xhci->devs[slot_id]->cmd_completion);
 794                 break;
 795         case TRB_TYPE(TRB_ADDR_DEV):
 796                 xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(event->status);
 797                 complete(&xhci->addr_dev);
 798                 break;
 799         case TRB_TYPE(TRB_STOP_RING):
 800                 handle_stopped_endpoint(xhci, xhci->cmd_ring->dequeue);
 801                 break;
 802         case TRB_TYPE(TRB_SET_DEQ):
 803                 handle_set_deq_completion(xhci, event, xhci->cmd_ring->dequeue);
 804                 break;
 805         case TRB_TYPE(TRB_CMD_NOOP):
 806                 ++xhci->noops_handled;
 807                 break;
 808         case TRB_TYPE(TRB_RESET_EP):
 809                 handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue);
 810                 break;
 811         default:
 812                 /* Skip over unknown commands on the event ring */
 813                 xhci->error_bitmask |= 1 << 6;
 814                 break;
 815         }
 816         inc_deq(xhci, xhci->cmd_ring, false);
 817 }
 818
 819 static void handle_port_status(struct xhci_hcd *xhci,
 820                 union xhci_trb *event)
 821 {
 822         u32 port_id;
 823
 824         /* Port status change events always have a successful completion code */
 825         if (GET_COMP_CODE(event->generic.field[2]) != COMP_SUCCESS) {
 826                 xhci_warn(xhci, "WARN: xHC returned failed port status event\n");
 827                 xhci->error_bitmask |= 1 << 8;
 828         }
 829         /* FIXME: core doesn't care about all port link state changes yet */
 830         port_id = GET_PORT_ID(event->generic.field[0]);
 831         xhci_dbg(xhci, "Port Status Change Event for port %d\n", port_id);
 832
 833         /* Update event ring dequeue pointer before dropping the lock */
 834         inc_deq(xhci, xhci->event_ring, true);
 835         xhci_set_hc_event_deq(xhci);
 836
 837         spin_unlock(&xhci->lock);
 838         /* Pass this up to the core */
 839         usb_hcd_poll_rh_status(xhci_to_hcd(xhci));
 840         spin_lock(&xhci->lock);
 841 }
 842
 843 /*
 844  * This TD is defined by the TRBs starting at start_trb in start_seg and ending
 845  * at end_trb, which may be in another segment.  If the suspect DMA address is a
 846  * TRB in this TD, this function returns that TRB's segment.  Otherwise it
 847  * returns 0.
 848  */
 849 static struct xhci_segment *trb_in_td(
 850                 struct xhci_segment *start_seg,
 851                 union xhci_trb  *start_trb,
 852                 union xhci_trb  *end_trb,
 853                 dma_addr_t      suspect_dma)
 854 {
 855         dma_addr_t start_dma;
 856         dma_addr_t end_seg_dma;
 857         dma_addr_t end_trb_dma;
 858         struct xhci_segment *cur_seg;
 859
 860         start_dma = xhci_trb_virt_to_dma(start_seg, start_trb);
 861         cur_seg = start_seg;
 862
 863         do {
 864                 /* We may get an event for a Link TRB in the middle of a TD */
 865                 end_seg_dma = xhci_trb_virt_to_dma(cur_seg,
 866                                 &start_seg->trbs[TRBS_PER_SEGMENT - 1]);
 867                 /* If the end TRB isn't in this segment, this is set to 0 */
 868                 end_trb_dma = xhci_trb_virt_to_dma(cur_seg, end_trb);
 869
 870                 if (end_trb_dma > 0) {
 871                         /* The end TRB is in this segment, so suspect should be here */
 872                         if (start_dma <= end_trb_dma) {
 873                                 if (suspect_dma >= start_dma && suspect_dma <= end_trb_dma)
 874                                         return cur_seg;
 875                         } else {
 876                                 /* Case for one segment with
 877                                  * a TD wrapped around to the top
 878                                  */
 879                                 if ((suspect_dma >= start_dma &&
 880                                                         suspect_dma <= end_seg_dma) ||
 881                                                 (suspect_dma >= cur_seg->dma &&
 882                                                  suspect_dma <= end_trb_dma))
 883                                         return cur_seg;
 884                         }
 885                         return 0;
 886                 } else {
 887                         /* Might still be somewhere in this segment */
 888                         if (suspect_dma >= start_dma && suspect_dma <= end_seg_dma)
 889                                 return cur_seg;
 890                 }
 891                 cur_seg = cur_seg->next;
 892                 start_dma = xhci_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]);
 893         } while (1);
 894
 895 }
 896
 897 /*
 898  * If this function returns an error condition, it means it got a Transfer
 899  * event with a corrupted Slot ID, Endpoint ID, or TRB DMA address.
 900  * At this point, the host controller is probably hosed and should be reset.
 901  */
 902 static int handle_tx_event(struct xhci_hcd *xhci,
 903                 struct xhci_transfer_event *event)
 904 {
 905         struct xhci_virt_device *xdev;
 906         struct xhci_virt_ep *ep;
 907         struct xhci_ring *ep_ring;
 908         unsigned int slot_id;
 909         int ep_index;
 910         struct xhci_td *td = 0;
 911         dma_addr_t event_dma;
 912         struct xhci_segment *event_seg;
 913         union xhci_trb *event_trb;
 914         struct urb *urb = 0;
 915         int status = -EINPROGRESS;
 916         struct xhci_ep_ctx *ep_ctx;
 917         u32 trb_comp_code;
 918
 919         xhci_dbg(xhci, "In %s\n", __func__);
 920         slot_id = TRB_TO_SLOT_ID(event->flags);
 921         xdev = xhci->devs[slot_id];
 922         if (!xdev) {
 923                 xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n");
 924                 return -ENODEV;
 925         }
 926
 927         /* Endpoint ID is 1 based, our index is zero based */
 928         ep_index = TRB_TO_EP_ID(event->flags) - 1;
 929         xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index);
 930         ep = &xdev->eps[ep_index];
 931         ep_ring = ep->ring;
 932         ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
 933         if (!ep_ring || (ep_ctx->ep_info & EP_STATE_MASK) == EP_STATE_DISABLED) {
 934                 xhci_err(xhci, "ERROR Transfer event pointed to disabled endpoint\n");
 935                 return -ENODEV;
 936         }
 937
 938         event_dma = event->buffer;
 939         /* This TRB should be in the TD at the head of this ring's TD list */
 940         xhci_dbg(xhci, "%s - checking for list empty\n", __func__);
 941         if (list_empty(&ep_ring->td_list)) {
 942                 xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n",
 943                                 TRB_TO_SLOT_ID(event->flags), ep_index);
 944                 xhci_dbg(xhci, "Event TRB with TRB type ID %u\n",
 945                                 (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10);
 946                 xhci_print_trb_offsets(xhci, (union xhci_trb *) event);
 947                 urb = NULL;
 948                 goto cleanup;
 949         }
 950         xhci_dbg(xhci, "%s - getting list entry\n", __func__);
 951         td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list);
 952
 953         /* Is this a TRB in the currently executing TD? */
 954         xhci_dbg(xhci, "%s - looking for TD\n", __func__);
 955         event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue,
 956                         td->last_trb, event_dma);
 957         xhci_dbg(xhci, "%s - found event_seg = %p\n", __func__, event_seg);
 958         if (!event_seg) {
 959                 /* HC is busted, give up! */
 960                 xhci_err(xhci, "ERROR Transfer event TRB DMA ptr not part of current TD\n");
 961                 return -ESHUTDOWN;
 962         }
 963         event_trb = &event_seg->trbs[(event_dma - event_seg->dma) / sizeof(*event_trb)];
 964         xhci_dbg(xhci, "Event TRB with TRB type ID %u\n",
 965                         (unsigned int) (event->flags & TRB_TYPE_BITMASK)>>10);
 966         xhci_dbg(xhci, "Offset 0x00 (buffer lo) = 0x%x\n",
 967                         lower_32_bits(event->buffer));
 968         xhci_dbg(xhci, "Offset 0x04 (buffer hi) = 0x%x\n",
 969                         upper_32_bits(event->buffer));
 970         xhci_dbg(xhci, "Offset 0x08 (transfer length) = 0x%x\n",
 971                         (unsigned int) event->transfer_len);
 972         xhci_dbg(xhci, "Offset 0x0C (flags) = 0x%x\n",
 973                         (unsigned int) event->flags);
 974
 975         /* Look for common error cases */
 976         trb_comp_code = GET_COMP_CODE(event->transfer_len);
 977         switch (trb_comp_code) {
 978         /* Skip codes that require special handling depending on
 979          * transfer type
 980          */
 981         case COMP_SUCCESS:
 982         case COMP_SHORT_TX:
 983                 break;
 984         case COMP_STOP:
 985                 xhci_dbg(xhci, "Stopped on Transfer TRB\n");
 986                 break;
 987         case COMP_STOP_INVAL:
 988                 xhci_dbg(xhci, "Stopped on No-op or Link TRB\n");
 989                 break;
 990         case COMP_STALL:
 991                 xhci_warn(xhci, "WARN: Stalled endpoint\n");
 992                 ep->ep_state |= EP_HALTED;
 993                 status = -EPIPE;
 994                 break;
 995         case COMP_TRB_ERR:
 996                 xhci_warn(xhci, "WARN: TRB error on endpoint\n");
 997                 status = -EILSEQ;
 998                 break;
 999         case COMP_TX_ERR:
1000                 xhci_warn(xhci, "WARN: transfer error on endpoint\n");
1001                 status = -EPROTO;
1002                 break;
1003         case COMP_BABBLE:
1004                 xhci_warn(xhci, "WARN: babble error on endpoint\n");
1005                 status = -EOVERFLOW;
1006                 break;
1007         case COMP_DB_ERR:
1008                 xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n");
1009                 status = -ENOSR;
1010                 break;
1011         default:
1012                 xhci_warn(xhci, "ERROR Unknown event condition, HC probably busted\n");
1013                 urb = NULL;
1014                 goto cleanup;
1015         }
1016         /* Now update the urb's actual_length and give back to the core */
1017         /* Was this a control transfer? */
1018         if (usb_endpoint_xfer_control(&td->urb->ep->desc)) {
1019                 xhci_debug_trb(xhci, xhci->event_ring->dequeue);
1020                 switch (trb_comp_code) {
1021                 case COMP_SUCCESS:
1022                         if (event_trb == ep_ring->dequeue) {
1023                                 xhci_warn(xhci, "WARN: Success on ctrl setup TRB without IOC set??\n");
1024                                 status = -ESHUTDOWN;
1025                         } else if (event_trb != td->last_trb) {
1026                                 xhci_warn(xhci, "WARN: Success on ctrl data TRB without IOC set??\n");
1027                                 status = -ESHUTDOWN;
1028                         } else {
1029                                 xhci_dbg(xhci, "Successful control transfer!\n");
1030                                 status = 0;
1031                         }
1032                         break;
1033                 case COMP_SHORT_TX:
1034                         xhci_warn(xhci, "WARN: short transfer on control ep\n");
1035                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1036                                 status = -EREMOTEIO;
1037                         else
1038                                 status = 0;
1039                         break;
1040                 case COMP_BABBLE:
1041                         /* The 0.96 spec says a babbling control endpoint
1042                          * is not halted. The 0.96 spec says it is.  Some HW
1043                          * claims to be 0.95 compliant, but it halts the control
1044                          * endpoint anyway.  Check if a babble halted the
1045                          * endpoint.
1046                          */
1047                         if (ep_ctx->ep_info != EP_STATE_HALTED)
1048                                 break;
1049                         /* else fall through */
1050                 case COMP_STALL:
1051                         /* Did we transfer part of the data (middle) phase? */
1052                         if (event_trb != ep_ring->dequeue &&
1053                                         event_trb != td->last_trb)
1054                                 td->urb->actual_length =
1055                                         td->urb->transfer_buffer_length
1056                                         - TRB_LEN(event->transfer_len);
1057                         else
1058                                 td->urb->actual_length = 0;
1059
1060                         ep->stopped_td = td;
1061                         ep->stopped_trb = event_trb;
1062                         xhci_queue_reset_ep(xhci, slot_id, ep_index);
1063                         xhci_cleanup_stalled_ring(xhci, td->urb->dev, ep_index);
1064                         xhci_ring_cmd_db(xhci);
1065                         goto td_cleanup;
1066                 default:
1067                         /* Others already handled above */
1068                         break;
1069                 }
1070                 /*
1071                  * Did we transfer any data, despite the errors that might have
1072                  * happened?  I.e. did we get past the setup stage?
1073                  */
1074                 if (event_trb != ep_ring->dequeue) {
1075                         /* The event was for the status stage */
1076                         if (event_trb == td->last_trb) {
1077                                 if (td->urb->actual_length != 0) {
1078                                         /* Don't overwrite a previously set error code */
1079                                         if ((status == -EINPROGRESS ||
1080                                                                 status == 0) &&
1081                                                         (td->urb->transfer_flags
1082                                                          & URB_SHORT_NOT_OK))
1083                                                 /* Did we already see a short data stage? */
1084                                                 status = -EREMOTEIO;
1085                                 } else {
1086                                         td->urb->actual_length =
1087                                                 td->urb->transfer_buffer_length;
1088                                 }
1089                         } else {
1090                         /* Maybe the event was for the data stage? */
1091                                 if (trb_comp_code != COMP_STOP_INVAL) {
1092                                         /* We didn't stop on a link TRB in the middle */
1093                                         td->urb->actual_length =
1094                                                 td->urb->transfer_buffer_length -
1095                                                 TRB_LEN(event->transfer_len);
1096                                         xhci_dbg(xhci, "Waiting for status stage event\n");
1097                                         urb = NULL;
1098                                         goto cleanup;
1099                                 }
1100                         }
1101                 }
1102         } else {
1103                 switch (trb_comp_code) {
1104                 case COMP_SUCCESS:
1105                         /* Double check that the HW transferred everything. */
1106                         if (event_trb != td->last_trb) {
1107                                 xhci_warn(xhci, "WARN Successful completion "
1108                                                 "on short TX\n");
1109                                 if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1110                                         status = -EREMOTEIO;
1111                                 else
1112                                         status = 0;
1113                         } else {
1114                                 if (usb_endpoint_xfer_bulk(&td->urb->ep->desc))
1115                                         xhci_dbg(xhci, "Successful bulk "
1116                                                         "transfer!\n");
1117                                 else
1118                                         xhci_dbg(xhci, "Successful interrupt "
1119                                                         "transfer!\n");
1120                                 status = 0;
1121                         }
1122                         break;
1123                 case COMP_SHORT_TX:
1124                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1125                                 status = -EREMOTEIO;
1126                         else
1127                                 status = 0;
1128                         break;
1129                 default:
1130                         /* Others already handled above */
1131                         break;
1132                 }
1133                 dev_dbg(&td->urb->dev->dev,
1134                                 "ep %#x - asked for %d bytes, "
1135                                 "%d bytes untransferred\n",
1136                                 td->urb->ep->desc.bEndpointAddress,
1137                                 td->urb->transfer_buffer_length,
1138                                 TRB_LEN(event->transfer_len));
1139                 /* Fast path - was this the last TRB in the TD for this URB? */
1140                 if (event_trb == td->last_trb) {
1141                         if (TRB_LEN(event->transfer_len) != 0) {
1142                                 td->urb->actual_length =
1143                                         td->urb->transfer_buffer_length -
1144                                         TRB_LEN(event->transfer_len);
1145                                 if (td->urb->transfer_buffer_length <
1146                                                 td->urb->actual_length) {
1147                                         xhci_warn(xhci, "HC gave bad length "
1148                                                         "of %d bytes left\n",
1149                                                         TRB_LEN(event->transfer_len));
1150                                         td->urb->actual_length = 0;
1151                                         if (td->urb->transfer_flags &
1152                                                         URB_SHORT_NOT_OK)
1153                                                 status = -EREMOTEIO;
1154                                         else
1155                                                 status = 0;
1156                                 }
1157                                 /* Don't overwrite a previously set error code */
1158                                 if (status == -EINPROGRESS) {
1159                                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1160                                                 status = -EREMOTEIO;
1161                                         else
1162                                                 status = 0;
1163                                 }
1164                         } else {
1165                                 td->urb->actual_length = td->urb->transfer_buffer_length;
1166                                 /* Ignore a short packet completion if the
1167                                  * untransferred length was zero.
1168                                  */
1169                                 if (status == -EREMOTEIO)
1170                                         status = 0;
1171                         }
1172                 } else {
1173                         /* Slow path - walk the list, starting from the dequeue
1174                          * pointer, to get the actual length transferred.
1175                          */
1176                         union xhci_trb *cur_trb;
1177                         struct xhci_segment *cur_seg;
1178
1179                         td->urb->actual_length = 0;
1180                         for (cur_trb = ep_ring->dequeue, cur_seg = ep_ring->deq_seg;
1181                                         cur_trb != event_trb;
1182                                         next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
1183                                 if (TRB_TYPE(cur_trb->generic.field[3]) != TRB_TR_NOOP &&
1184                                                 TRB_TYPE(cur_trb->generic.field[3]) != TRB_LINK)
1185                                         td->urb->actual_length +=
1186                                                 TRB_LEN(cur_trb->generic.field[2]);
1187                         }
1188                         /* If the ring didn't stop on a Link or No-op TRB, add
1189                          * in the actual bytes transferred from the Normal TRB
1190                          */
1191                         if (trb_comp_code != COMP_STOP_INVAL)
1192                                 td->urb->actual_length +=
1193                                         TRB_LEN(cur_trb->generic.field[2]) -
1194                                         TRB_LEN(event->transfer_len);
1195                 }
1196         }
1197         if (trb_comp_code == COMP_STOP_INVAL ||
1198                         trb_comp_code == COMP_STOP) {
1199                 /* The Endpoint Stop Command completion will take care of any
1200                  * stopped TDs.  A stopped TD may be restarted, so don't update
1201                  * the ring dequeue pointer or take this TD off any lists yet.
1202                  */
1203                 ep->stopped_td = td;
1204                 ep->stopped_trb = event_trb;
1205         } else {
1206                 if (trb_comp_code == COMP_STALL ||
1207                                 trb_comp_code == COMP_BABBLE) {
1208                         /* The transfer is completed from the driver's
1209                          * perspective, but we need to issue a set dequeue
1210                          * command for this stalled endpoint to move the dequeue
1211                          * pointer past the TD.  We can't do that here because
1212                          * the halt condition must be cleared first.
1213                          */
1214                         ep->stopped_td = td;
1215                         ep->stopped_trb = event_trb;
1216                 } else {
1217                         /* Update ring dequeue pointer */
1218                         while (ep_ring->dequeue != td->last_trb)
1219                                 inc_deq(xhci, ep_ring, false);
1220                         inc_deq(xhci, ep_ring, false);
1221                 }
1222
1223 td_cleanup:
1224                 /* Clean up the endpoint's TD list */
1225                 urb = td->urb;
1226                 /* Do one last check of the actual transfer length.
1227                  * If the host controller said we transferred more data than
1228                  * the buffer length, urb->actual_length will be a very big
1229                  * number (since it's unsigned).  Play it safe and say we didn't
1230                  * transfer anything.
1231                  */
1232                 if (urb->actual_length > urb->transfer_buffer_length) {
1233                         xhci_warn(xhci, "URB transfer length is wrong, "
1234                                         "xHC issue? req. len = %u, "
1235                                         "act. len = %u\n",
1236                                         urb->transfer_buffer_length,
1237                                         urb->actual_length);
1238                         urb->actual_length = 0;
1239                         if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
1240                                 status = -EREMOTEIO;
1241                         else
1242                                 status = 0;
1243                 }
1244                 list_del(&td->td_list);
1245                 /* Was this TD slated to be cancelled but completed anyway? */
1246                 if (!list_empty(&td->cancelled_td_list)) {
1247                         list_del(&td->cancelled_td_list);
1248                         ep->cancels_pending--;
1249                 }
1250                 /* Leave the TD around for the reset endpoint function to use
1251                  * (but only if it's not a control endpoint, since we already
1252                  * queued the Set TR dequeue pointer command for stalled
1253                  * control endpoints).
1254                  */
1255                 if (usb_endpoint_xfer_control(&urb->ep->desc) ||
1256                         (trb_comp_code != COMP_STALL &&
1257                                 trb_comp_code != COMP_BABBLE)) {
1258                         kfree(td);
1259                 }
1260                 urb->hcpriv = NULL;
1261         }
1262 cleanup:
1263         inc_deq(xhci, xhci->event_ring, true);
1264         xhci_set_hc_event_deq(xhci);
1265
1266         /* FIXME for multi-TD URBs (who have buffers bigger than 64MB) */
1267         if (urb) {
1268                 usb_hcd_unlink_urb_from_ep(xhci_to_hcd(xhci), urb);
1269                 xhci_dbg(xhci, "Giveback URB %p, len = %d, status = %d\n",
1270                                 urb, urb->actual_length, status);
1271                 spin_unlock(&xhci->lock);
1272                 usb_hcd_giveback_urb(xhci_to_hcd(xhci), urb, status);
1273                 spin_lock(&xhci->lock);
1274         }
1275         return 0;
1276 }
1277
1278 /*
1279  * This function handles all OS-owned events on the event ring.  It may drop
1280  * xhci->lock between event processing (e.g. to pass up port status changes).
1281  */
1282 void xhci_handle_event(struct xhci_hcd *xhci)
1283 {
1284         union xhci_trb *event;
1285         int update_ptrs = 1;
1286         int ret;
1287
1288         xhci_dbg(xhci, "In %s\n", __func__);
1289         if (!xhci->event_ring || !xhci->event_ring->dequeue) {
1290                 xhci->error_bitmask |= 1 << 1;
1291                 return;
1292         }
1293
1294         event = xhci->event_ring->dequeue;
1295         /* Does the HC or OS own the TRB? */
1296         if ((event->event_cmd.flags & TRB_CYCLE) !=
1297                         xhci->event_ring->cycle_state) {
1298                 xhci->error_bitmask |= 1 << 2;
1299                 return;
1300         }
1301         xhci_dbg(xhci, "%s - OS owns TRB\n", __func__);
1302
1303         /* FIXME: Handle more event types. */
1304         switch ((event->event_cmd.flags & TRB_TYPE_BITMASK)) {
1305         case TRB_TYPE(TRB_COMPLETION):
1306                 xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__);
1307                 handle_cmd_completion(xhci, &event->event_cmd);
1308                 xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__);
1309                 break;
1310         case TRB_TYPE(TRB_PORT_STATUS):
1311                 xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__);
1312                 handle_port_status(xhci, event);
1313                 xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__);
1314                 update_ptrs = 0;
1315                 break;
1316         case TRB_TYPE(TRB_TRANSFER):
1317                 xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__);
1318                 ret = handle_tx_event(xhci, &event->trans_event);
1319                 xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__);
1320                 if (ret < 0)
1321                         xhci->error_bitmask |= 1 << 9;
1322                 else
1323                         update_ptrs = 0;
1324                 break;
1325         default:
1326                 xhci->error_bitmask |= 1 << 3;
1327         }
1328
1329         if (update_ptrs) {
1330                 /* Update SW and HC event ring dequeue pointer */
1331                 inc_deq(xhci, xhci->event_ring, true);
1332                 xhci_set_hc_event_deq(xhci);
1333         }
1334         /* Are there more items on the event ring? */
1335         xhci_handle_event(xhci);
1336 }
1337
1338 /****           Endpoint Ring Operations        ****/
1339
1340 /*
1341  * Generic function for queueing a TRB on a ring.
1342  * The caller must have checked to make sure there's room on the ring.
1343  */
1344 static void queue_trb(struct xhci_hcd *xhci, struct xhci_ring *ring,
1345                 bool consumer,
1346                 u32 field1, u32 field2, u32 field3, u32 field4)
1347 {
1348         struct xhci_generic_trb *trb;
1349
1350         trb = &ring->enqueue->generic;
1351         trb->field[0] = field1;
1352         trb->field[1] = field2;
1353         trb->field[2] = field3;
1354         trb->field[3] = field4;
1355         inc_enq(xhci, ring, consumer);
1356 }
1357
1358 /*
1359  * Does various checks on the endpoint ring, and makes it ready to queue num_trbs.
1360  * FIXME allocate segments if the ring is full.
1361  */
1362 static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
1363                 u32 ep_state, unsigned int num_trbs, gfp_t mem_flags)
1364 {
1365         /* Make sure the endpoint has been added to xHC schedule */
1366         xhci_dbg(xhci, "Endpoint state = 0x%x\n", ep_state);
1367         switch (ep_state) {
1368         case EP_STATE_DISABLED:
1369                 /*
1370                  * USB core changed config/interfaces without notifying us,
1371                  * or hardware is reporting the wrong state.
1372                  */
1373                 xhci_warn(xhci, "WARN urb submitted to disabled ep\n");
1374                 return -ENOENT;
1375         case EP_STATE_ERROR:
1376                 xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n");
1377                 /* FIXME event handling code for error needs to clear it */
1378                 /* XXX not sure if this should be -ENOENT or not */
1379                 return -EINVAL;
1380         case EP_STATE_HALTED:
1381                 xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n");
1382         case EP_STATE_STOPPED:
1383         case EP_STATE_RUNNING:
1384                 break;
1385         default:
1386                 xhci_err(xhci, "ERROR unknown endpoint state for ep\n");
1387                 /*
1388                  * FIXME issue Configure Endpoint command to try to get the HC
1389                  * back into a known state.
1390                  */
1391                 return -EINVAL;
1392         }
1393         if (!room_on_ring(xhci, ep_ring, num_trbs)) {
1394                 /* FIXME allocate more room */
1395                 xhci_err(xhci, "ERROR no room on ep ring\n");
1396                 return -ENOMEM;
1397         }
1398         return 0;
1399 }
1400
1401 static int prepare_transfer(struct xhci_hcd *xhci,
1402                 struct xhci_virt_device *xdev,
1403                 unsigned int ep_index,
1404                 unsigned int num_trbs,
1405                 struct urb *urb,
1406                 struct xhci_td **td,
1407                 gfp_t mem_flags)
1408 {
1409         int ret;
1410         struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
1411         ret = prepare_ring(xhci, xdev->eps[ep_index].ring,
1412                         ep_ctx->ep_info & EP_STATE_MASK,
1413                         num_trbs, mem_flags);
1414         if (ret)
1415                 return ret;
1416         *td = kzalloc(sizeof(struct xhci_td), mem_flags);
1417         if (!*td)
1418                 return -ENOMEM;
1419         INIT_LIST_HEAD(&(*td)->td_list);
1420         INIT_LIST_HEAD(&(*td)->cancelled_td_list);
1421
1422         ret = usb_hcd_link_urb_to_ep(xhci_to_hcd(xhci), urb);
1423         if (unlikely(ret)) {
1424                 kfree(*td);
1425                 return ret;
1426         }
1427
1428         (*td)->urb = urb;
1429         urb->hcpriv = (void *) (*td);
1430         /* Add this TD to the tail of the endpoint ring's TD list */
1431         list_add_tail(&(*td)->td_list, &xdev->eps[ep_index].ring->td_list);
1432         (*td)->start_seg = xdev->eps[ep_index].ring->enq_seg;
1433         (*td)->first_trb = xdev->eps[ep_index].ring->enqueue;
1434
1435         return 0;
1436 }
1437
1438 static unsigned int count_sg_trbs_needed(struct xhci_hcd *xhci, struct urb *urb)
1439 {
1440         int num_sgs, num_trbs, running_total, temp, i;
1441         struct scatterlist *sg;
1442
1443         sg = NULL;
1444         num_sgs = urb->num_sgs;
1445         temp = urb->transfer_buffer_length;
1446
1447         xhci_dbg(xhci, "count sg list trbs: \n");
1448         num_trbs = 0;
1449         for_each_sg(urb->sg->sg, sg, num_sgs, i) {
1450                 unsigned int previous_total_trbs = num_trbs;
1451                 unsigned int len = sg_dma_len(sg);
1452
1453                 /* Scatter gather list entries may cross 64KB boundaries */
1454                 running_total = TRB_MAX_BUFF_SIZE -
1455                         (sg_dma_address(sg) & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
1456                 if (running_total != 0)
1457                         num_trbs++;
1458
1459                 /* How many more 64KB chunks to transfer, how many more TRBs? */
1460                 while (running_total < sg_dma_len(sg)) {
1461                         num_trbs++;
1462                         running_total += TRB_MAX_BUFF_SIZE;
1463                 }
1464                 xhci_dbg(xhci, " sg #%d: dma = %#llx, len = %#x (%d), num_trbs = %d\n",
1465                                 i, (unsigned long long)sg_dma_address(sg),
1466                                 len, len, num_trbs - previous_total_trbs);
1467
1468                 len = min_t(int, len, temp);
1469                 temp -= len;
1470                 if (temp == 0)
1471                         break;
1472         }
1473         xhci_dbg(xhci, "\n");
1474         if (!in_interrupt())
1475                 dev_dbg(&urb->dev->dev, "ep %#x - urb len = %d, sglist used, num_trbs = %d\n",
1476                                 urb->ep->desc.bEndpointAddress,
1477                                 urb->transfer_buffer_length,
1478                                 num_trbs);
1479         return num_trbs;
1480 }
1481
1482 static void check_trb_math(struct urb *urb, int num_trbs, int running_total)
1483 {
1484         if (num_trbs != 0)
1485                 dev_dbg(&urb->dev->dev, "%s - ep %#x - Miscalculated number of "
1486                                 "TRBs, %d left\n", __func__,
1487                                 urb->ep->desc.bEndpointAddress, num_trbs);
1488         if (running_total != urb->transfer_buffer_length)
1489                 dev_dbg(&urb->dev->dev, "%s - ep %#x - Miscalculated tx length, "
1490                                 "queued %#x (%d), asked for %#x (%d)\n",
1491                                 __func__,
1492                                 urb->ep->desc.bEndpointAddress,
1493                                 running_total, running_total,
1494                                 urb->transfer_buffer_length,
1495                                 urb->transfer_buffer_length);
1496 }
1497
1498 static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id,
1499                 unsigned int ep_index, int start_cycle,
1500                 struct xhci_generic_trb *start_trb, struct xhci_td *td)
1501 {
1502         /*
1503          * Pass all the TRBs to the hardware at once and make sure this write
1504          * isn't reordered.
1505          */
1506         wmb();
1507         start_trb->field[3] |= start_cycle;
1508         ring_ep_doorbell(xhci, slot_id, ep_index);
1509 }
1510
1511 /*
1512  * xHCI uses normal TRBs for both bulk and interrupt.  When the interrupt
1513  * endpoint is to be serviced, the xHC will consume (at most) one TD.  A TD
1514  * (comprised of sg list entries) can take several service intervals to
1515  * transmit.
1516  */
1517 int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
1518                 struct urb *urb, int slot_id, unsigned int ep_index)
1519 {
1520         struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci,
1521                         xhci->devs[slot_id]->out_ctx, ep_index);
1522         int xhci_interval;
1523         int ep_interval;
1524
1525         xhci_interval = EP_INTERVAL_TO_UFRAMES(ep_ctx->ep_info);
1526         ep_interval = urb->interval;
1527         /* Convert to microframes */
1528         if (urb->dev->speed == USB_SPEED_LOW ||
1529                         urb->dev->speed == USB_SPEED_FULL)
1530                 ep_interval *= 8;
1531         /* FIXME change this to a warning and a suggestion to use the new API
1532          * to set the polling interval (once the API is added).
1533          */
1534         if (xhci_interval != ep_interval) {
1535                 if (!printk_ratelimit())
1536                         dev_dbg(&urb->dev->dev, "Driver uses different interval"
1537                                         " (%d microframe%s) than xHCI "
1538                                         "(%d microframe%s)\n",
1539                                         ep_interval,
1540                                         ep_interval == 1 ? "" : "s",
1541                                         xhci_interval,
1542                                         xhci_interval == 1 ? "" : "s");
1543                 urb->interval = xhci_interval;
1544                 /* Convert back to frames for LS/FS devices */
1545                 if (urb->dev->speed == USB_SPEED_LOW ||
1546                                 urb->dev->speed == USB_SPEED_FULL)
1547                         urb->interval /= 8;
1548         }
1549         return xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index);
1550 }
1551
1552 static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
1553                 struct urb *urb, int slot_id, unsigned int ep_index)
1554 {
1555         struct xhci_ring *ep_ring;
1556         unsigned int num_trbs;
1557         struct xhci_td *td;
1558         struct scatterlist *sg;
1559         int num_sgs;
1560         int trb_buff_len, this_sg_len, running_total;
1561         bool first_trb;
1562         u64 addr;
1563
1564         struct xhci_generic_trb *start_trb;
1565         int start_cycle;
1566
1567         ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
1568         num_trbs = count_sg_trbs_needed(xhci, urb);
1569         num_sgs = urb->num_sgs;
1570
1571         trb_buff_len = prepare_transfer(xhci, xhci->devs[slot_id],
1572                         ep_index, num_trbs, urb, &td, mem_flags);
1573         if (trb_buff_len < 0)
1574                 return trb_buff_len;
1575         /*
1576          * Don't give the first TRB to the hardware (by toggling the cycle bit)
1577          * until we've finished creating all the other TRBs.  The ring's cycle
1578          * state may change as we enqueue the other TRBs, so save it too.
1579          */
1580         start_trb = &ep_ring->enqueue->generic;
1581         start_cycle = ep_ring->cycle_state;
1582
1583         running_total = 0;
1584         /*
1585          * How much data is in the first TRB?
1586          *
1587          * There are three forces at work for TRB buffer pointers and lengths:
1588          * 1. We don't want to walk off the end of this sg-list entry buffer.
1589          * 2. The transfer length that the driver requested may be smaller than
1590          *    the amount of memory allocated for this scatter-gather list.
1591          * 3. TRBs buffers can't cross 64KB boundaries.
1592          */
1593         sg = urb->sg->sg;
1594         addr = (u64) sg_dma_address(sg);
1595         this_sg_len = sg_dma_len(sg);
1596         trb_buff_len = TRB_MAX_BUFF_SIZE -
1597                 (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
1598         trb_buff_len = min_t(int, trb_buff_len, this_sg_len);
1599         if (trb_buff_len > urb->transfer_buffer_length)
1600                 trb_buff_len = urb->transfer_buffer_length;
1601         xhci_dbg(xhci, "First length to xfer from 1st sglist entry = %u\n",
1602                         trb_buff_len);
1603
1604         first_trb = true;
1605         /* Queue the first TRB, even if it's zero-length */
1606         do {
1607                 u32 field = 0;
1608                 u32 length_field = 0;
1609
1610                 /* Don't change the cycle bit of the first TRB until later */
1611                 if (first_trb)
1612                         first_trb = false;
1613                 else
1614                         field |= ep_ring->cycle_state;
1615
1616                 /* Chain all the TRBs together; clear the chain bit in the last
1617                  * TRB to indicate it's the last TRB in the chain.
1618                  */
1619                 if (num_trbs > 1) {
1620                         field |= TRB_CHAIN;
1621                 } else {
1622                         /* FIXME - add check for ZERO_PACKET flag before this */
1623                         td->last_trb = ep_ring->enqueue;
1624                         field |= TRB_IOC;
1625                 }
1626                 xhci_dbg(xhci, " sg entry: dma = %#x, len = %#x (%d), "
1627                                 "64KB boundary at %#x, end dma = %#x\n",
1628                                 (unsigned int) addr, trb_buff_len, trb_buff_len,
1629                                 (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
1630                                 (unsigned int) addr + trb_buff_len);
1631                 if (TRB_MAX_BUFF_SIZE -
1632                                 (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1)) < trb_buff_len) {
1633                         xhci_warn(xhci, "WARN: sg dma xfer crosses 64KB boundaries!\n");
1634                         xhci_dbg(xhci, "Next boundary at %#x, end dma = %#x\n",
1635                                         (unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
1636                                         (unsigned int) addr + trb_buff_len);
1637                 }
1638                 length_field = TRB_LEN(trb_buff_len) |
1639                         TD_REMAINDER(urb->transfer_buffer_length - running_total) |
1640                         TRB_INTR_TARGET(0);
1641                 queue_trb(xhci, ep_ring, false,
1642                                 lower_32_bits(addr),
1643                                 upper_32_bits(addr),
1644                                 length_field,
1645                                 /* We always want to know if the TRB was short,
1646                                  * or we won't get an event when it completes.
1647                                  * (Unless we use event data TRBs, which are a
1648                                  * waste of space and HC resources.)
1649                                  */
1650                                 field | TRB_ISP | TRB_TYPE(TRB_NORMAL));
1651                 --num_trbs;
1652                 running_total += trb_buff_len;
1653
1654                 /* Calculate length for next transfer --
1655                  * Are we done queueing all the TRBs for this sg entry?
1656                  */
1657                 this_sg_len -= trb_buff_len;
1658                 if (this_sg_len == 0) {
1659                         --num_sgs;
1660                         if (num_sgs == 0)
1661                                 break;
1662                         sg = sg_next(sg);
1663                         addr = (u64) sg_dma_address(sg);
1664                         this_sg_len = sg_dma_len(sg);
1665                 } else {
1666                         addr += trb_buff_len;
1667                 }
1668
1669                 trb_buff_len = TRB_MAX_BUFF_SIZE -
1670                         (addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
1671                 trb_buff_len = min_t(int, trb_buff_len, this_sg_len);
1672                 if (running_total + trb_buff_len > urb->transfer_buffer_length)
1673                         trb_buff_len =
1674                                 urb->transfer_buffer_length - running_total;
1675         } while (running_total < urb->transfer_buffer_length);
1676
1677         check_trb_math(urb, num_trbs, running_total);
1678         giveback_first_trb(xhci, slot_id, ep_index, start_cycle, start_trb, td);
1679         return 0;
1680 }
1681
1682 /* This is very similar to what ehci-q.c qtd_fill() does */
1683 int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
1684                 struct urb *urb, int slot_id, unsigned int ep_index)
1685 {
1686         struct xhci_ring *ep_ring;
1687         struct xhci_td *td;
1688         int num_trbs;
1689         struct xhci_generic_trb *start_trb;
1690         bool first_trb;
1691         int start_cycle;
1692         u32 field, length_field;
1693
1694         int running_total, trb_buff_len, ret;
1695         u64 addr;
1696
1697         if (urb->sg)
1698                 return queue_bulk_sg_tx(xhci, mem_flags, urb, slot_id, ep_index);
1699
1700         ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
1701
1702         num_trbs = 0;
1703         /* How much data is (potentially) left before the 64KB boundary? */
1704         running_total = TRB_MAX_BUFF_SIZE -
1705                 (urb->transfer_dma & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
1706
1707         /* If there's some data on this 64KB chunk, or we have to send a
1708          * zero-length transfer, we need at least one TRB
1709          */
1710         if (running_total != 0 || urb->transfer_buffer_length == 0)
1711                 num_trbs++;
1712         /* How many more 64KB chunks to transfer, how many more TRBs? */
1713         while (running_total < urb->transfer_buffer_length) {
1714                 num_trbs++;
1715                 running_total += TRB_MAX_BUFF_SIZE;
1716         }
1717         /* FIXME: this doesn't deal with URB_ZERO_PACKET - need one more */
1718
1719         if (!in_interrupt())
1720                 dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d), addr = %#llx, num_trbs = %d\n",
1721                                 urb->ep->desc.bEndpointAddress,
1722                                 urb->transfer_buffer_length,
1723                                 urb->transfer_buffer_length,
1724                                 (unsigned long long)urb->transfer_dma,
1725                                 num_trbs);
1726
1727         ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index,
1728                         num_trbs, urb, &td, mem_flags);
1729         if (ret < 0)
1730                 return ret;
1731
1732         /*
1733          * Don't give the first TRB to the hardware (by toggling the cycle bit)
1734          * until we've finished creating all the other TRBs.  The ring's cycle
1735          * state may change as we enqueue the other TRBs, so save it too.
1736          */
1737         start_trb = &ep_ring->enqueue->generic;
1738         start_cycle = ep_ring->cycle_state;
1739
1740         running_total = 0;
1741         /* How much data is in the first TRB? */
1742         addr = (u64) urb->transfer_dma;
1743         trb_buff_len = TRB_MAX_BUFF_SIZE -
1744                 (urb->transfer_dma & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
1745         if (urb->transfer_buffer_length < trb_buff_len)
1746                 trb_buff_len = urb->transfer_buffer_length;
1747
1748         first_trb = true;
1749
1750         /* Queue the first TRB, even if it's zero-length */
1751         do {
1752                 field = 0;
1753
1754                 /* Don't change the cycle bit of the first TRB until later */
1755                 if (first_trb)
1756                         first_trb = false;
1757                 else
1758                         field |= ep_ring->cycle_state;
1759
1760                 /* Chain all the TRBs together; clear the chain bit in the last
1761                  * TRB to indicate it's the last TRB in the chain.
1762                  */
1763                 if (num_trbs > 1) {
1764                         field |= TRB_CHAIN;
1765                 } else {
1766                         /* FIXME - add check for ZERO_PACKET flag before this */
1767                         td->last_trb = ep_ring->enqueue;
1768                         field |= TRB_IOC;
1769                 }
1770                 length_field = TRB_LEN(trb_buff_len) |
1771                         TD_REMAINDER(urb->transfer_buffer_length - running_total) |
1772                         TRB_INTR_TARGET(0);
1773                 queue_trb(xhci, ep_ring, false,
1774                                 lower_32_bits(addr),
1775                                 upper_32_bits(addr),
1776                                 length_field,
1777                                 /* We always want to know if the TRB was short,
1778                                  * or we won't get an event when it completes.
1779                                  * (Unless we use event data TRBs, which are a
1780                                  * waste of space and HC resources.)
1781                                  */
1782                                 field | TRB_ISP | TRB_TYPE(TRB_NORMAL));
1783                 --num_trbs;
1784                 running_total += trb_buff_len;
1785
1786                 /* Calculate length for next transfer */
1787                 addr += trb_buff_len;
1788                 trb_buff_len = urb->transfer_buffer_length - running_total;
1789                 if (trb_buff_len > TRB_MAX_BUFF_SIZE)
1790                         trb_buff_len = TRB_MAX_BUFF_SIZE;
1791         } while (running_total < urb->transfer_buffer_length);
1792
1793         check_trb_math(urb, num_trbs, running_total);
1794         giveback_first_trb(xhci, slot_id, ep_index, start_cycle, start_trb, td);
1795         return 0;
1796 }
1797
1798 /* Caller must have locked xhci->lock */
1799 int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
1800                 struct urb *urb, int slot_id, unsigned int ep_index)
1801 {
1802         struct xhci_ring *ep_ring;
1803         int num_trbs;
1804         int ret;
1805         struct usb_ctrlrequest *setup;
1806         struct xhci_generic_trb *start_trb;
1807         int start_cycle;
1808         u32 field, length_field;
1809         struct xhci_td *td;
1810
1811         ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
1812
1813         /*
1814          * Need to copy setup packet into setup TRB, so we can't use the setup
1815          * DMA address.
1816          */
1817         if (!urb->setup_packet)
1818                 return -EINVAL;
1819
1820         if (!in_interrupt())
1821                 xhci_dbg(xhci, "Queueing ctrl tx for slot id %d, ep %d\n",
1822                                 slot_id, ep_index);
1823         /* 1 TRB for setup, 1 for status */
1824         num_trbs = 2;
1825         /*
1826          * Don't need to check if we need additional event data and normal TRBs,
1827          * since data in control transfers will never get bigger than 16MB
1828          * XXX: can we get a buffer that crosses 64KB boundaries?
1829          */
1830         if (urb->transfer_buffer_length > 0)
1831                 num_trbs++;
1832         ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index, num_trbs,
1833                         urb, &td, mem_flags);
1834         if (ret < 0)
1835                 return ret;
1836
1837         /*
1838          * Don't give the first TRB to the hardware (by toggling the cycle bit)
1839          * until we've finished creating all the other TRBs.  The ring's cycle
1840          * state may change as we enqueue the other TRBs, so save it too.
1841          */
1842         start_trb = &ep_ring->enqueue->generic;
1843         start_cycle = ep_ring->cycle_state;
1844
1845         /* Queue setup TRB - see section 6.4.1.2.1 */
1846         /* FIXME better way to translate setup_packet into two u32 fields? */
1847         setup = (struct usb_ctrlrequest *) urb->setup_packet;
1848         queue_trb(xhci, ep_ring, false,
1849                         /* FIXME endianness is probably going to bite my ass here. */
1850                         setup->bRequestType | setup->bRequest << 8 | setup->wValue << 16,
1851                         setup->wIndex | setup->wLength << 16,
1852                         TRB_LEN(8) | TRB_INTR_TARGET(0),
1853                         /* Immediate data in pointer */
1854                         TRB_IDT | TRB_TYPE(TRB_SETUP));
1855
1856         /* If there's data, queue data TRBs */
1857         field = 0;
1858         length_field = TRB_LEN(urb->transfer_buffer_length) |
1859                 TD_REMAINDER(urb->transfer_buffer_length) |
1860                 TRB_INTR_TARGET(0);
1861         if (urb->transfer_buffer_length > 0) {
1862                 if (setup->bRequestType & USB_DIR_IN)
1863                         field |= TRB_DIR_IN;
1864                 queue_trb(xhci, ep_ring, false,
1865                                 lower_32_bits(urb->transfer_dma),
1866                                 upper_32_bits(urb->transfer_dma),
1867                                 length_field,
1868                                 /* Event on short tx */
1869                                 field | TRB_ISP | TRB_TYPE(TRB_DATA) | ep_ring->cycle_state);
1870         }
1871
1872         /* Save the DMA address of the last TRB in the TD */
1873         td->last_trb = ep_ring->enqueue;
1874
1875         /* Queue status TRB - see Table 7 and sections 4.11.2.2 and 6.4.1.2.3 */
1876         /* If the device sent data, the status stage is an OUT transfer */
1877         if (urb->transfer_buffer_length > 0 && setup->bRequestType & USB_DIR_IN)
1878                 field = 0;
1879         else
1880                 field = TRB_DIR_IN;
1881         queue_trb(xhci, ep_ring, false,
1882                         0,
1883                         0,
1884                         TRB_INTR_TARGET(0),
1885                         /* Event on completion */
1886                         field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state);
1887
1888         giveback_first_trb(xhci, slot_id, ep_index, start_cycle, start_trb, td);
1889         return 0;
1890 }
1891
1892 /****           Command Ring Operations         ****/
1893
1894 /* Generic function for queueing a command TRB on the command ring.
1895  * Check to make sure there's room on the command ring for one command TRB.
1896  * Also check that there's room reserved for commands that must not fail.
1897  * If this is a command that must not fail, meaning command_must_succeed = TRUE,
1898  * then only check for the number of reserved spots.
1899  * Don't decrement xhci->cmd_ring_reserved_trbs after we've queued the TRB
1900  * because the command event handler may want to resubmit a failed command.
1901  */
1902 static int queue_command(struct xhci_hcd *xhci, u32 field1, u32 field2,
1903                 u32 field3, u32 field4, bool command_must_succeed)
1904 {
1905         int reserved_trbs = xhci->cmd_ring_reserved_trbs;
1906         if (!command_must_succeed)
1907                 reserved_trbs++;
1908
1909         if (!room_on_ring(xhci, xhci->cmd_ring, reserved_trbs)) {
1910                 if (!in_interrupt())
1911                         xhci_err(xhci, "ERR: No room for command on command ring\n");
1912                 if (command_must_succeed)
1913                         xhci_err(xhci, "ERR: Reserved TRB counting for "
1914                                         "unfailable commands failed.\n");
1915                 return -ENOMEM;
1916         }
1917         queue_trb(xhci, xhci->cmd_ring, false, field1, field2, field3,
1918                         field4 | xhci->cmd_ring->cycle_state);
1919         return 0;
1920 }
1921
1922 /* Queue a no-op command on the command ring */
1923 static int queue_cmd_noop(struct xhci_hcd *xhci)
1924 {
1925         return queue_command(xhci, 0, 0, 0, TRB_TYPE(TRB_CMD_NOOP), false);
1926 }
1927
1928 /*
1929  * Place a no-op command on the command ring to test the command and
1930  * event ring.
1931  */
1932 void *xhci_setup_one_noop(struct xhci_hcd *xhci)
1933 {
1934         if (queue_cmd_noop(xhci) < 0)
1935                 return NULL;
1936         xhci->noops_submitted++;
1937         return xhci_ring_cmd_db;
1938 }
1939
1940 /* Queue a slot enable or disable request on the command ring */
1941 int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id)
1942 {
1943         return queue_command(xhci, 0, 0, 0,
1944                         TRB_TYPE(trb_type) | SLOT_ID_FOR_TRB(slot_id), false);
1945 }
1946
1947 /* Queue an address device command TRB */
1948 int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
1949                 u32 slot_id)
1950 {
1951         return queue_command(xhci, lower_32_bits(in_ctx_ptr),
1952                         upper_32_bits(in_ctx_ptr), 0,
1953                         TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id),
1954                         false);
1955 }
1956
1957 /* Queue a configure endpoint command TRB */
1958 int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
1959                 u32 slot_id, bool command_must_succeed)
1960 {
1961         return queue_command(xhci, lower_32_bits(in_ctx_ptr),
1962                         upper_32_bits(in_ctx_ptr), 0,
1963                         TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id),
1964                         command_must_succeed);
1965 }
1966
1967 /* Queue an evaluate context command TRB */
1968 int xhci_queue_evaluate_context(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
1969                 u32 slot_id)
1970 {
1971         return queue_command(xhci, lower_32_bits(in_ctx_ptr),
1972                         upper_32_bits(in_ctx_ptr), 0,
1973                         TRB_TYPE(TRB_EVAL_CONTEXT) | SLOT_ID_FOR_TRB(slot_id),
1974                         false);
1975 }
1976
1977 int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, int slot_id,
1978                 unsigned int ep_index)
1979 {
1980         u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
1981         u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
1982         u32 type = TRB_TYPE(TRB_STOP_RING);
1983
1984         return queue_command(xhci, 0, 0, 0,
1985                         trb_slot_id | trb_ep_index | type, false);
1986 }
1987
1988 /* Set Transfer Ring Dequeue Pointer command.
1989  * This should not be used for endpoints that have streams enabled.
1990  */
1991 static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
1992                 unsigned int ep_index, struct xhci_segment *deq_seg,
1993                 union xhci_trb *deq_ptr, u32 cycle_state)
1994 {
1995         dma_addr_t addr;
1996         u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
1997         u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
1998         u32 type = TRB_TYPE(TRB_SET_DEQ);
1999
2000         addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr);
2001         if (addr == 0) {
2002                 xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n");
2003                 xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n",
2004                                 deq_seg, deq_ptr);
2005                 return 0;
2006         }
2007         return queue_command(xhci, lower_32_bits(addr) | cycle_state,
2008                         upper_32_bits(addr), 0,
2009                         trb_slot_id | trb_ep_index | type, false);
2010 }
2011
2012 int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
2013                 unsigned int ep_index)
2014 {
2015         u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
2016         u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
2017         u32 type = TRB_TYPE(TRB_RESET_EP);
2018
2019         return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type,
2020                         false);
2021 }