drivers/tty/serial/sunsu.c

   1 /*
   2  * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
   3  *
   4  * Copyright (C) 1997  Eddie C. Dost  (ecd@skynet.be)
   5  * Copyright (C) 1998-1999  Pete Zaitcev   (zaitcev@yahoo.com)
   6  *
   7  * This is mainly a variation of 8250.c, credits go to authors mentioned
   8  * therein.  In fact this driver should be merged into the generic 8250.c
   9  * infrastructure perhaps using a 8250_sparc.c module.
  10  *
  11  * Fixed to use tty_get_baud_rate().
  12  *   Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
  13  *
  14  * Converted to new 2.5.x UART layer.
  15  *   David S. Miller (davem@davemloft.net), 2002-Jul-29
  16  */
  17
  18 #include <linux/module.h>
  19 #include <linux/kernel.h>
  20 #include <linux/spinlock.h>
  21 #include <linux/errno.h>
  22 #include <linux/tty.h>
  23 #include <linux/tty_flip.h>
  24 #include <linux/major.h>
  25 #include <linux/string.h>
  26 #include <linux/ptrace.h>
  27 #include <linux/ioport.h>
  28 #include <linux/circ_buf.h>
  29 #include <linux/serial.h>
  30 #include <linux/sysrq.h>
  31 #include <linux/console.h>
  32 #include <linux/slab.h>
  33 #ifdef CONFIG_SERIO
  34 #include <linux/serio.h>
  35 #endif
  36 #include <linux/serial_reg.h>
  37 #include <linux/init.h>
  38 #include <linux/delay.h>
  39 #include <linux/of_device.h>
  40
  41 #include <asm/io.h>
  42 #include <asm/irq.h>
  43 #include <asm/prom.h>
  44
  45 #if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
  46 #define SUPPORT_SYSRQ
  47 #endif
  48
  49 #include <linux/serial_core.h>
  50
  51 #include "suncore.h"
  52
  53 /* We are on a NS PC87303 clocked with 24.0 MHz, which results
  54  * in a UART clock of 1.8462 MHz.
  55  */
  56 #define SU_BASE_BAUD    (1846200 / 16)
  57
  58 enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
  59 static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };
  60
  61 /*
  62  * Here we define the default xmit fifo size used for each type of UART.
  63  */
  64 static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
  65         { "unknown",    1,      0 },
  66         { "8250",       1,      0 },
  67         { "16450",      1,      0 },
  68         { "16550",      1,      0 },
  69         { "16550A",     16,     UART_CLEAR_FIFO | UART_USE_FIFO },
  70         { "Cirrus",     1,      0 },
  71         { "ST16650",    1,      UART_CLEAR_FIFO | UART_STARTECH },
  72         { "ST16650V2",  32,     UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
  73         { "TI16750",    64,     UART_CLEAR_FIFO | UART_USE_FIFO },
  74         { "Startech",   1,      0 },
  75         { "16C950/954", 128,    UART_CLEAR_FIFO | UART_USE_FIFO },
  76         { "ST16654",    64,     UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
  77         { "XR16850",    128,    UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
  78         { "RSA",        2048,   UART_CLEAR_FIFO | UART_USE_FIFO }
  79 };
  80
  81 struct uart_sunsu_port {
  82         struct uart_port        port;
  83         unsigned char           acr;
  84         unsigned char           ier;
  85         unsigned short          rev;
  86         unsigned char           lcr;
  87         unsigned int            lsr_break_flag;
  88         unsigned int            cflag;
  89
  90         /* Probing information.  */
  91         enum su_type            su_type;
  92         unsigned int            type_probed;    /* XXX Stupid */
  93         unsigned long           reg_size;
  94
  95 #ifdef CONFIG_SERIO
  96         struct serio            serio;
  97         int                     serio_open;
  98 #endif
  99 };
 100
 101 static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
 102 {
 103         offset <<= up->port.regshift;
 104
 105         switch (up->port.iotype) {
 106         case UPIO_HUB6:
 107                 outb(up->port.hub6 - 1 + offset, up->port.iobase);
 108                 return inb(up->port.iobase + 1);
 109
 110         case UPIO_MEM:
 111                 return readb(up->port.membase + offset);
 112
 113         default:
 114                 return inb(up->port.iobase + offset);
 115         }
 116 }
 117
 118 static void serial_out(struct uart_sunsu_port *up, int offset, int value)
 119 {
 120 #ifndef CONFIG_SPARC64
 121         /*
 122          * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
 123          * connected with a gate then go to SlavIO. When IRQ4 goes tristated
 124          * gate outputs a logical one. Since we use level triggered interrupts
 125          * we have lockup and watchdog reset. We cannot mask IRQ because
 126          * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
 127          * This problem is similar to what Alpha people suffer, see serial.c.
 128          */
 129         if (offset == UART_MCR)
 130                 value |= UART_MCR_OUT2;
 131 #endif
 132         offset <<= up->port.regshift;
 133
 134         switch (up->port.iotype) {
 135         case UPIO_HUB6:
 136                 outb(up->port.hub6 - 1 + offset, up->port.iobase);
 137                 outb(value, up->port.iobase + 1);
 138                 break;
 139
 140         case UPIO_MEM:
 141                 writeb(value, up->port.membase + offset);
 142                 break;
 143
 144         default:
 145                 outb(value, up->port.iobase + offset);
 146         }
 147 }
 148
 149 /*
 150  * We used to support using pause I/O for certain machines.  We
 151  * haven't supported this for a while, but just in case it's badly
 152  * needed for certain old 386 machines, I've left these #define's
 153  * in....
 154  */
 155 #define serial_inp(up, offset)          serial_in(up, offset)
 156 #define serial_outp(up, offset, value)  serial_out(up, offset, value)
 157
 158
 159 /*
 160  * For the 16C950
 161  */
 162 static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
 163 {
 164         serial_out(up, UART_SCR, offset);
 165         serial_out(up, UART_ICR, value);
 166 }
 167
 168 #if 0 /* Unused currently */
 169 static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
 170 {
 171         unsigned int value;
 172
 173         serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
 174         serial_out(up, UART_SCR, offset);
 175         value = serial_in(up, UART_ICR);
 176         serial_icr_write(up, UART_ACR, up->acr);
 177
 178         return value;
 179 }
 180 #endif
 181
 182 #ifdef CONFIG_SERIAL_8250_RSA
 183 /*
 184  * Attempts to turn on the RSA FIFO.  Returns zero on failure.
 185  * We set the port uart clock rate if we succeed.
 186  */
 187 static int __enable_rsa(struct uart_sunsu_port *up)
 188 {
 189         unsigned char mode;
 190         int result;
 191
 192         mode = serial_inp(up, UART_RSA_MSR);
 193         result = mode & UART_RSA_MSR_FIFO;
 194
 195         if (!result) {
 196                 serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
 197                 mode = serial_inp(up, UART_RSA_MSR);
 198                 result = mode & UART_RSA_MSR_FIFO;
 199         }
 200
 201         if (result)
 202                 up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
 203
 204         return result;
 205 }
 206
 207 static void enable_rsa(struct uart_sunsu_port *up)
 208 {
 209         if (up->port.type == PORT_RSA) {
 210                 if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
 211                         spin_lock_irq(&up->port.lock);
 212                         __enable_rsa(up);
 213                         spin_unlock_irq(&up->port.lock);
 214                 }
 215                 if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
 216                         serial_outp(up, UART_RSA_FRR, 0);
 217         }
 218 }
 219
 220 /*
 221  * Attempts to turn off the RSA FIFO.  Returns zero on failure.
 222  * It is unknown why interrupts were disabled in here.  However,
 223  * the caller is expected to preserve this behaviour by grabbing
 224  * the spinlock before calling this function.
 225  */
 226 static void disable_rsa(struct uart_sunsu_port *up)
 227 {
 228         unsigned char mode;
 229         int result;
 230
 231         if (up->port.type == PORT_RSA &&
 232             up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
 233                 spin_lock_irq(&up->port.lock);
 234
 235                 mode = serial_inp(up, UART_RSA_MSR);
 236                 result = !(mode & UART_RSA_MSR_FIFO);
 237
 238                 if (!result) {
 239                         serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
 240                         mode = serial_inp(up, UART_RSA_MSR);
 241                         result = !(mode & UART_RSA_MSR_FIFO);
 242                 }
 243
 244                 if (result)
 245                         up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
 246                 spin_unlock_irq(&up->port.lock);
 247         }
 248 }
 249 #endif /* CONFIG_SERIAL_8250_RSA */
 250
 251 static inline void __stop_tx(struct uart_sunsu_port *p)
 252 {
 253         if (p->ier & UART_IER_THRI) {
 254                 p->ier &= ~UART_IER_THRI;
 255                 serial_out(p, UART_IER, p->ier);
 256         }
 257 }
 258
 259 static void sunsu_stop_tx(struct uart_port *port)
 260 {
 261         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 262
 263         __stop_tx(up);
 264
 265         /*
 266          * We really want to stop the transmitter from sending.
 267          */
 268         if (up->port.type == PORT_16C950) {
 269                 up->acr |= UART_ACR_TXDIS;
 270                 serial_icr_write(up, UART_ACR, up->acr);
 271         }
 272 }
 273
 274 static void sunsu_start_tx(struct uart_port *port)
 275 {
 276         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 277
 278         if (!(up->ier & UART_IER_THRI)) {
 279                 up->ier |= UART_IER_THRI;
 280                 serial_out(up, UART_IER, up->ier);
 281         }
 282
 283         /*
 284          * Re-enable the transmitter if we disabled it.
 285          */
 286         if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
 287                 up->acr &= ~UART_ACR_TXDIS;
 288                 serial_icr_write(up, UART_ACR, up->acr);
 289         }
 290 }
 291
 292 static void sunsu_stop_rx(struct uart_port *port)
 293 {
 294         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 295
 296         up->ier &= ~UART_IER_RLSI;
 297         up->port.read_status_mask &= ~UART_LSR_DR;
 298         serial_out(up, UART_IER, up->ier);
 299 }
 300
 301 static void sunsu_enable_ms(struct uart_port *port)
 302 {
 303         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 304         unsigned long flags;
 305
 306         spin_lock_irqsave(&up->port.lock, flags);
 307         up->ier |= UART_IER_MSI;
 308         serial_out(up, UART_IER, up->ier);
 309         spin_unlock_irqrestore(&up->port.lock, flags);
 310 }
 311
 312 static struct tty_struct *
 313 receive_chars(struct uart_sunsu_port *up, unsigned char *status)
 314 {
 315         struct tty_struct *tty = up->port.state->port.tty;
 316         unsigned char ch, flag;
 317         int max_count = 256;
 318         int saw_console_brk = 0;
 319
 320         do {
 321                 ch = serial_inp(up, UART_RX);
 322                 flag = TTY_NORMAL;
 323                 up->port.icount.rx++;
 324
 325                 if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
 326                                        UART_LSR_FE | UART_LSR_OE))) {
 327                         /*
 328                          * For statistics only
 329                          */
 330                         if (*status & UART_LSR_BI) {
 331                                 *status &= ~(UART_LSR_FE | UART_LSR_PE);
 332                                 up->port.icount.brk++;
 333                                 if (up->port.cons != NULL &&
 334                                     up->port.line == up->port.cons->index)
 335                                         saw_console_brk = 1;
 336                                 /*
 337                                  * We do the SysRQ and SAK checking
 338                                  * here because otherwise the break
 339                                  * may get masked by ignore_status_mask
 340                                  * or read_status_mask.
 341                                  */
 342                                 if (uart_handle_break(&up->port))
 343                                         goto ignore_char;
 344                         } else if (*status & UART_LSR_PE)
 345                                 up->port.icount.parity++;
 346                         else if (*status & UART_LSR_FE)
 347                                 up->port.icount.frame++;
 348                         if (*status & UART_LSR_OE)
 349                                 up->port.icount.overrun++;
 350
 351                         /*
 352                          * Mask off conditions which should be ingored.
 353                          */
 354                         *status &= up->port.read_status_mask;
 355
 356                         if (up->port.cons != NULL &&
 357                             up->port.line == up->port.cons->index) {
 358                                 /* Recover the break flag from console xmit */
 359                                 *status |= up->lsr_break_flag;
 360                                 up->lsr_break_flag = 0;
 361                         }
 362
 363                         if (*status & UART_LSR_BI) {
 364                                 flag = TTY_BREAK;
 365                         } else if (*status & UART_LSR_PE)
 366                                 flag = TTY_PARITY;
 367                         else if (*status & UART_LSR_FE)
 368                                 flag = TTY_FRAME;
 369                 }
 370                 if (uart_handle_sysrq_char(&up->port, ch))
 371                         goto ignore_char;
 372                 if ((*status & up->port.ignore_status_mask) == 0)
 373                         tty_insert_flip_char(tty, ch, flag);
 374                 if (*status & UART_LSR_OE)
 375                         /*
 376                          * Overrun is special, since it's reported
 377                          * immediately, and doesn't affect the current
 378                          * character.
 379                          */
 380                          tty_insert_flip_char(tty, 0, TTY_OVERRUN);
 381         ignore_char:
 382                 *status = serial_inp(up, UART_LSR);
 383         } while ((*status & UART_LSR_DR) && (max_count-- > 0));
 384
 385         if (saw_console_brk)
 386                 sun_do_break();
 387
 388         return tty;
 389 }
 390
 391 static void transmit_chars(struct uart_sunsu_port *up)
 392 {
 393         struct circ_buf *xmit = &up->port.state->xmit;
 394         int count;
 395
 396         if (up->port.x_char) {
 397                 serial_outp(up, UART_TX, up->port.x_char);
 398                 up->port.icount.tx++;
 399                 up->port.x_char = 0;
 400                 return;
 401         }
 402         if (uart_tx_stopped(&up->port)) {
 403                 sunsu_stop_tx(&up->port);
 404                 return;
 405         }
 406         if (uart_circ_empty(xmit)) {
 407                 __stop_tx(up);
 408                 return;
 409         }
 410
 411         count = up->port.fifosize;
 412         do {
 413                 serial_out(up, UART_TX, xmit->buf[xmit->tail]);
 414                 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
 415                 up->port.icount.tx++;
 416                 if (uart_circ_empty(xmit))
 417                         break;
 418         } while (--count > 0);
 419
 420         if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 421                 uart_write_wakeup(&up->port);
 422
 423         if (uart_circ_empty(xmit))
 424                 __stop_tx(up);
 425 }
 426
 427 static void check_modem_status(struct uart_sunsu_port *up)
 428 {
 429         int status;
 430
 431         status = serial_in(up, UART_MSR);
 432
 433         if ((status & UART_MSR_ANY_DELTA) == 0)
 434                 return;
 435
 436         if (status & UART_MSR_TERI)
 437                 up->port.icount.rng++;
 438         if (status & UART_MSR_DDSR)
 439                 up->port.icount.dsr++;
 440         if (status & UART_MSR_DDCD)
 441                 uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
 442         if (status & UART_MSR_DCTS)
 443                 uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
 444
 445         wake_up_interruptible(&up->port.state->port.delta_msr_wait);
 446 }
 447
 448 static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id)
 449 {
 450         struct uart_sunsu_port *up = dev_id;
 451         unsigned long flags;
 452         unsigned char status;
 453
 454         spin_lock_irqsave(&up->port.lock, flags);
 455
 456         do {
 457                 struct tty_struct *tty;
 458
 459                 status = serial_inp(up, UART_LSR);
 460                 tty = NULL;
 461                 if (status & UART_LSR_DR)
 462                         tty = receive_chars(up, &status);
 463                 check_modem_status(up);
 464                 if (status & UART_LSR_THRE)
 465                         transmit_chars(up);
 466
 467                 spin_unlock_irqrestore(&up->port.lock, flags);
 468
 469                 if (tty)
 470                         tty_flip_buffer_push(tty);
 471
 472                 spin_lock_irqsave(&up->port.lock, flags);
 473
 474         } while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));
 475
 476         spin_unlock_irqrestore(&up->port.lock, flags);
 477
 478         return IRQ_HANDLED;
 479 }
 480
 481 /* Separate interrupt handling path for keyboard/mouse ports.  */
 482
 483 static void
 484 sunsu_change_speed(struct uart_port *port, unsigned int cflag,
 485                    unsigned int iflag, unsigned int quot);
 486
 487 static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
 488 {
 489         unsigned int cur_cflag = up->cflag;
 490         int quot, new_baud;
 491
 492         up->cflag &= ~CBAUD;
 493         up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);
 494
 495         quot = up->port.uartclk / (16 * new_baud);
 496
 497         sunsu_change_speed(&up->port, up->cflag, 0, quot);
 498 }
 499
 500 static void receive_kbd_ms_chars(struct uart_sunsu_port *up, int is_break)
 501 {
 502         do {
 503                 unsigned char ch = serial_inp(up, UART_RX);
 504
 505                 /* Stop-A is handled by drivers/char/keyboard.c now. */
 506                 if (up->su_type == SU_PORT_KBD) {
 507 #ifdef CONFIG_SERIO
 508                         serio_interrupt(&up->serio, ch, 0);
 509 #endif
 510                 } else if (up->su_type == SU_PORT_MS) {
 511                         int ret = suncore_mouse_baud_detection(ch, is_break);
 512
 513                         switch (ret) {
 514                         case 2:
 515                                 sunsu_change_mouse_baud(up);
 516                                 /* fallthru */
 517                         case 1:
 518                                 break;
 519
 520                         case 0:
 521 #ifdef CONFIG_SERIO
 522                                 serio_interrupt(&up->serio, ch, 0);
 523 #endif
 524                                 break;
 525                         };
 526                 }
 527         } while (serial_in(up, UART_LSR) & UART_LSR_DR);
 528 }
 529
 530 static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id)
 531 {
 532         struct uart_sunsu_port *up = dev_id;
 533
 534         if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
 535                 unsigned char status = serial_inp(up, UART_LSR);
 536
 537                 if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
 538                         receive_kbd_ms_chars(up, (status & UART_LSR_BI) != 0);
 539         }
 540
 541         return IRQ_HANDLED;
 542 }
 543
 544 static unsigned int sunsu_tx_empty(struct uart_port *port)
 545 {
 546         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 547         unsigned long flags;
 548         unsigned int ret;
 549
 550         spin_lock_irqsave(&up->port.lock, flags);
 551         ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
 552         spin_unlock_irqrestore(&up->port.lock, flags);
 553
 554         return ret;
 555 }
 556
 557 static unsigned int sunsu_get_mctrl(struct uart_port *port)
 558 {
 559         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 560         unsigned char status;
 561         unsigned int ret;
 562
 563         status = serial_in(up, UART_MSR);
 564
 565         ret = 0;
 566         if (status & UART_MSR_DCD)
 567                 ret |= TIOCM_CAR;
 568         if (status & UART_MSR_RI)
 569                 ret |= TIOCM_RNG;
 570         if (status & UART_MSR_DSR)
 571                 ret |= TIOCM_DSR;
 572         if (status & UART_MSR_CTS)
 573                 ret |= TIOCM_CTS;
 574         return ret;
 575 }
 576
 577 static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
 578 {
 579         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 580         unsigned char mcr = 0;
 581
 582         if (mctrl & TIOCM_RTS)
 583                 mcr |= UART_MCR_RTS;
 584         if (mctrl & TIOCM_DTR)
 585                 mcr |= UART_MCR_DTR;
 586         if (mctrl & TIOCM_OUT1)
 587                 mcr |= UART_MCR_OUT1;
 588         if (mctrl & TIOCM_OUT2)
 589                 mcr |= UART_MCR_OUT2;
 590         if (mctrl & TIOCM_LOOP)
 591                 mcr |= UART_MCR_LOOP;
 592
 593         serial_out(up, UART_MCR, mcr);
 594 }
 595
 596 static void sunsu_break_ctl(struct uart_port *port, int break_state)
 597 {
 598         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 599         unsigned long flags;
 600
 601         spin_lock_irqsave(&up->port.lock, flags);
 602         if (break_state == -1)
 603                 up->lcr |= UART_LCR_SBC;
 604         else
 605                 up->lcr &= ~UART_LCR_SBC;
 606         serial_out(up, UART_LCR, up->lcr);
 607         spin_unlock_irqrestore(&up->port.lock, flags);
 608 }
 609
 610 static int sunsu_startup(struct uart_port *port)
 611 {
 612         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 613         unsigned long flags;
 614         int retval;
 615
 616         if (up->port.type == PORT_16C950) {
 617                 /* Wake up and initialize UART */
 618                 up->acr = 0;
 619                 serial_outp(up, UART_LCR, 0xBF);
 620                 serial_outp(up, UART_EFR, UART_EFR_ECB);
 621                 serial_outp(up, UART_IER, 0);
 622                 serial_outp(up, UART_LCR, 0);
 623                 serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
 624                 serial_outp(up, UART_LCR, 0xBF);
 625                 serial_outp(up, UART_EFR, UART_EFR_ECB);
 626                 serial_outp(up, UART_LCR, 0);
 627         }
 628
 629 #ifdef CONFIG_SERIAL_8250_RSA
 630         /*
 631          * If this is an RSA port, see if we can kick it up to the
 632          * higher speed clock.
 633          */
 634         enable_rsa(up);
 635 #endif
 636
 637         /*
 638          * Clear the FIFO buffers and disable them.
 639          * (they will be reenabled in set_termios())
 640          */
 641         if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
 642                 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
 643                 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 644                                 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
 645                 serial_outp(up, UART_FCR, 0);
 646         }
 647
 648         /*
 649          * Clear the interrupt registers.
 650          */
 651         (void) serial_inp(up, UART_LSR);
 652         (void) serial_inp(up, UART_RX);
 653         (void) serial_inp(up, UART_IIR);
 654         (void) serial_inp(up, UART_MSR);
 655
 656         /*
 657          * At this point, there's no way the LSR could still be 0xff;
 658          * if it is, then bail out, because there's likely no UART
 659          * here.
 660          */
 661         if (!(up->port.flags & UPF_BUGGY_UART) &&
 662             (serial_inp(up, UART_LSR) == 0xff)) {
 663                 printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
 664                 return -ENODEV;
 665         }
 666
 667         if (up->su_type != SU_PORT_PORT) {
 668                 retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
 669                                      IRQF_SHARED, su_typev[up->su_type], up);
 670         } else {
 671                 retval = request_irq(up->port.irq, sunsu_serial_interrupt,
 672                                      IRQF_SHARED, su_typev[up->su_type], up);
 673         }
 674         if (retval) {
 675                 printk("su: Cannot register IRQ %d\n", up->port.irq);
 676                 return retval;
 677         }
 678
 679         /*
 680          * Now, initialize the UART
 681          */
 682         serial_outp(up, UART_LCR, UART_LCR_WLEN8);
 683
 684         spin_lock_irqsave(&up->port.lock, flags);
 685
 686         up->port.mctrl |= TIOCM_OUT2;
 687
 688         sunsu_set_mctrl(&up->port, up->port.mctrl);
 689         spin_unlock_irqrestore(&up->port.lock, flags);
 690
 691         /*
 692          * Finally, enable interrupts.  Note: Modem status interrupts
 693          * are set via set_termios(), which will be occurring imminently
 694          * anyway, so we don't enable them here.
 695          */
 696         up->ier = UART_IER_RLSI | UART_IER_RDI;
 697         serial_outp(up, UART_IER, up->ier);
 698
 699         if (up->port.flags & UPF_FOURPORT) {
 700                 unsigned int icp;
 701                 /*
 702                  * Enable interrupts on the AST Fourport board
 703                  */
 704                 icp = (up->port.iobase & 0xfe0) | 0x01f;
 705                 outb_p(0x80, icp);
 706                 (void) inb_p(icp);
 707         }
 708
 709         /*
 710          * And clear the interrupt registers again for luck.
 711          */
 712         (void) serial_inp(up, UART_LSR);
 713         (void) serial_inp(up, UART_RX);
 714         (void) serial_inp(up, UART_IIR);
 715         (void) serial_inp(up, UART_MSR);
 716
 717         return 0;
 718 }
 719
 720 static void sunsu_shutdown(struct uart_port *port)
 721 {
 722         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 723         unsigned long flags;
 724
 725         /*
 726          * Disable interrupts from this port
 727          */
 728         up->ier = 0;
 729         serial_outp(up, UART_IER, 0);
 730
 731         spin_lock_irqsave(&up->port.lock, flags);
 732         if (up->port.flags & UPF_FOURPORT) {
 733                 /* reset interrupts on the AST Fourport board */
 734                 inb((up->port.iobase & 0xfe0) | 0x1f);
 735                 up->port.mctrl |= TIOCM_OUT1;
 736         } else
 737                 up->port.mctrl &= ~TIOCM_OUT2;
 738
 739         sunsu_set_mctrl(&up->port, up->port.mctrl);
 740         spin_unlock_irqrestore(&up->port.lock, flags);
 741
 742         /*
 743          * Disable break condition and FIFOs
 744          */
 745         serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
 746         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
 747                                   UART_FCR_CLEAR_RCVR |
 748                                   UART_FCR_CLEAR_XMIT);
 749         serial_outp(up, UART_FCR, 0);
 750
 751 #ifdef CONFIG_SERIAL_8250_RSA
 752         /*
 753          * Reset the RSA board back to 115kbps compat mode.
 754          */
 755         disable_rsa(up);
 756 #endif
 757
 758         /*
 759          * Read data port to reset things.
 760          */
 761         (void) serial_in(up, UART_RX);
 762
 763         free_irq(up->port.irq, up);
 764 }
 765
 766 static void
 767 sunsu_change_speed(struct uart_port *port, unsigned int cflag,
 768                    unsigned int iflag, unsigned int quot)
 769 {
 770         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 771         unsigned char cval, fcr = 0;
 772         unsigned long flags;
 773
 774         switch (cflag & CSIZE) {
 775         case CS5:
 776                 cval = 0x00;
 777                 break;
 778         case CS6:
 779                 cval = 0x01;
 780                 break;
 781         case CS7:
 782                 cval = 0x02;
 783                 break;
 784         default:
 785         case CS8:
 786                 cval = 0x03;
 787                 break;
 788         }
 789
 790         if (cflag & CSTOPB)
 791                 cval |= 0x04;
 792         if (cflag & PARENB)
 793                 cval |= UART_LCR_PARITY;
 794         if (!(cflag & PARODD))
 795                 cval |= UART_LCR_EPAR;
 796 #ifdef CMSPAR
 797         if (cflag & CMSPAR)
 798                 cval |= UART_LCR_SPAR;
 799 #endif
 800
 801         /*
 802          * Work around a bug in the Oxford Semiconductor 952 rev B
 803          * chip which causes it to seriously miscalculate baud rates
 804          * when DLL is 0.
 805          */
 806         if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
 807             up->rev == 0x5201)
 808                 quot ++;
 809
 810         if (uart_config[up->port.type].flags & UART_USE_FIFO) {
 811                 if ((up->port.uartclk / quot) < (2400 * 16))
 812                         fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
 813 #ifdef CONFIG_SERIAL_8250_RSA
 814                 else if (up->port.type == PORT_RSA)
 815                         fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
 816 #endif
 817                 else
 818                         fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
 819         }
 820         if (up->port.type == PORT_16750)
 821                 fcr |= UART_FCR7_64BYTE;
 822
 823         /*
 824          * Ok, we're now changing the port state.  Do it with
 825          * interrupts disabled.
 826          */
 827         spin_lock_irqsave(&up->port.lock, flags);
 828
 829         /*
 830          * Update the per-port timeout.
 831          */
 832         uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));
 833
 834         up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
 835         if (iflag & INPCK)
 836                 up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
 837         if (iflag & (BRKINT | PARMRK))
 838                 up->port.read_status_mask |= UART_LSR_BI;
 839
 840         /*
 841          * Characteres to ignore
 842          */
 843         up->port.ignore_status_mask = 0;
 844         if (iflag & IGNPAR)
 845                 up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
 846         if (iflag & IGNBRK) {
 847                 up->port.ignore_status_mask |= UART_LSR_BI;
 848                 /*
 849                  * If we're ignoring parity and break indicators,
 850                  * ignore overruns too (for real raw support).
 851                  */
 852                 if (iflag & IGNPAR)
 853                         up->port.ignore_status_mask |= UART_LSR_OE;
 854         }
 855
 856         /*
 857          * ignore all characters if CREAD is not set
 858          */
 859         if ((cflag & CREAD) == 0)
 860                 up->port.ignore_status_mask |= UART_LSR_DR;
 861
 862         /*
 863          * CTS flow control flag and modem status interrupts
 864          */
 865         up->ier &= ~UART_IER_MSI;
 866         if (UART_ENABLE_MS(&up->port, cflag))
 867                 up->ier |= UART_IER_MSI;
 868
 869         serial_out(up, UART_IER, up->ier);
 870
 871         if (uart_config[up->port.type].flags & UART_STARTECH) {
 872                 serial_outp(up, UART_LCR, 0xBF);
 873                 serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
 874         }
 875         serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
 876         serial_outp(up, UART_DLL, quot & 0xff);         /* LS of divisor */
 877         serial_outp(up, UART_DLM, quot >> 8);           /* MS of divisor */
 878         if (up->port.type == PORT_16750)
 879                 serial_outp(up, UART_FCR, fcr);         /* set fcr */
 880         serial_outp(up, UART_LCR, cval);                /* reset DLAB */
 881         up->lcr = cval;                                 /* Save LCR */
 882         if (up->port.type != PORT_16750) {
 883                 if (fcr & UART_FCR_ENABLE_FIFO) {
 884                         /* emulated UARTs (Lucent Venus 167x) need two steps */
 885                         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
 886                 }
 887                 serial_outp(up, UART_FCR, fcr);         /* set fcr */
 888         }
 889
 890         up->cflag = cflag;
 891
 892         spin_unlock_irqrestore(&up->port.lock, flags);
 893 }
 894
 895 static void
 896 sunsu_set_termios(struct uart_port *port, struct ktermios *termios,
 897                   struct ktermios *old)
 898 {
 899         unsigned int baud, quot;
 900
 901         /*
 902          * Ask the core to calculate the divisor for us.
 903          */
 904         baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
 905         quot = uart_get_divisor(port, baud);
 906
 907         sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
 908 }
 909
 910 static void sunsu_release_port(struct uart_port *port)
 911 {
 912 }
 913
 914 static int sunsu_request_port(struct uart_port *port)
 915 {
 916         return 0;
 917 }
 918
 919 static void sunsu_config_port(struct uart_port *port, int flags)
 920 {
 921         struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
 922
 923         if (flags & UART_CONFIG_TYPE) {
 924                 /*
 925                  * We are supposed to call autoconfig here, but this requires
 926                  * splitting all the OBP probing crap from the UART probing.
 927                  * We'll do it when we kill sunsu.c altogether.
 928                  */
 929                 port->type = up->type_probed;   /* XXX */
 930         }
 931 }
 932
 933 static int
 934 sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
 935 {
 936         return -EINVAL;
 937 }
 938
 939 static const char *
 940 sunsu_type(struct uart_port *port)
 941 {
 942         int type = port->type;
 943
 944         if (type >= ARRAY_SIZE(uart_config))
 945                 type = 0;
 946         return uart_config[type].name;
 947 }
 948
 949 static struct uart_ops sunsu_pops = {
 950         .tx_empty       = sunsu_tx_empty,
 951         .set_mctrl      = sunsu_set_mctrl,
 952         .get_mctrl      = sunsu_get_mctrl,
 953         .stop_tx        = sunsu_stop_tx,
 954         .start_tx       = sunsu_start_tx,
 955         .stop_rx        = sunsu_stop_rx,
 956         .enable_ms      = sunsu_enable_ms,
 957         .break_ctl      = sunsu_break_ctl,
 958         .startup        = sunsu_startup,
 959         .shutdown       = sunsu_shutdown,
 960         .set_termios    = sunsu_set_termios,
 961         .type           = sunsu_type,
 962         .release_port   = sunsu_release_port,
 963         .request_port   = sunsu_request_port,
 964         .config_port    = sunsu_config_port,
 965         .verify_port    = sunsu_verify_port,
 966 };
 967
 968 #define UART_NR 4
 969
 970 static struct uart_sunsu_port sunsu_ports[UART_NR];
 971
 972 #ifdef CONFIG_SERIO
 973
 974 static DEFINE_SPINLOCK(sunsu_serio_lock);
 975
 976 static int sunsu_serio_write(struct serio *serio, unsigned char ch)
 977 {
 978         struct uart_sunsu_port *up = serio->port_data;
 979         unsigned long flags;
 980         int lsr;
 981
 982         spin_lock_irqsave(&sunsu_serio_lock, flags);
 983
 984         do {
 985                 lsr = serial_in(up, UART_LSR);
 986         } while (!(lsr & UART_LSR_THRE));
 987
 988         /* Send the character out. */
 989         serial_out(up, UART_TX, ch);
 990
 991         spin_unlock_irqrestore(&sunsu_serio_lock, flags);
 992
 993         return 0;
 994 }
 995
 996 static int sunsu_serio_open(struct serio *serio)
 997 {
 998         struct uart_sunsu_port *up = serio->port_data;
 999         unsigned long flags;
1000         int ret;
1001
1002         spin_lock_irqsave(&sunsu_serio_lock, flags);
1003         if (!up->serio_open) {
1004                 up->serio_open = 1;
1005                 ret = 0;
1006         } else
1007                 ret = -EBUSY;
1008         spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1009
1010         return ret;
1011 }
1012
1013 static void sunsu_serio_close(struct serio *serio)
1014 {
1015         struct uart_sunsu_port *up = serio->port_data;
1016         unsigned long flags;
1017
1018         spin_lock_irqsave(&sunsu_serio_lock, flags);
1019         up->serio_open = 0;
1020         spin_unlock_irqrestore(&sunsu_serio_lock, flags);
1021 }
1022
1023 #endif /* CONFIG_SERIO */
1024
1025 static void sunsu_autoconfig(struct uart_sunsu_port *up)
1026 {
1027         unsigned char status1, status2, scratch, scratch2, scratch3;
1028         unsigned char save_lcr, save_mcr;
1029         unsigned long flags;
1030
1031         if (up->su_type == SU_PORT_NONE)
1032                 return;
1033
1034         up->type_probed = PORT_UNKNOWN;
1035         up->port.iotype = UPIO_MEM;
1036
1037         spin_lock_irqsave(&up->port.lock, flags);
1038
1039         if (!(up->port.flags & UPF_BUGGY_UART)) {
1040                 /*
1041                  * Do a simple existence test first; if we fail this, there's
1042                  * no point trying anything else.
1043                  *
1044                  * 0x80 is used as a nonsense port to prevent against false
1045                  * positives due to ISA bus float.  The assumption is that
1046                  * 0x80 is a non-existent port; which should be safe since
1047                  * include/asm/io.h also makes this assumption.
1048                  */
1049                 scratch = serial_inp(up, UART_IER);
1050                 serial_outp(up, UART_IER, 0);
1051 #ifdef __i386__
1052                 outb(0xff, 0x080);
1053 #endif
1054                 scratch2 = serial_inp(up, UART_IER);
1055                 serial_outp(up, UART_IER, 0x0f);
1056 #ifdef __i386__
1057                 outb(0, 0x080);
1058 #endif
1059                 scratch3 = serial_inp(up, UART_IER);
1060                 serial_outp(up, UART_IER, scratch);
1061                 if (scratch2 != 0 || scratch3 != 0x0F)
1062                         goto out;       /* We failed; there's nothing here */
1063         }
1064
1065         save_mcr = serial_in(up, UART_MCR);
1066         save_lcr = serial_in(up, UART_LCR);
1067
1068         /*
1069          * Check to see if a UART is really there.  Certain broken
1070          * internal modems based on the Rockwell chipset fail this
1071          * test, because they apparently don't implement the loopback
1072          * test mode.  So this test is skipped on the COM 1 through
1073          * COM 4 ports.  This *should* be safe, since no board
1074          * manufacturer would be stupid enough to design a board
1075          * that conflicts with COM 1-4 --- we hope!
1076          */
1077         if (!(up->port.flags & UPF_SKIP_TEST)) {
1078                 serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
1079                 status1 = serial_inp(up, UART_MSR) & 0xF0;
1080                 serial_outp(up, UART_MCR, save_mcr);
1081                 if (status1 != 0x90)
1082                         goto out;       /* We failed loopback test */
1083         }
1084         serial_outp(up, UART_LCR, 0xBF);        /* set up for StarTech test */
1085         serial_outp(up, UART_EFR, 0);           /* EFR is the same as FCR */
1086         serial_outp(up, UART_LCR, 0);
1087         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1088         scratch = serial_in(up, UART_IIR) >> 6;
1089         switch (scratch) {
1090                 case 0:
1091                         up->port.type = PORT_16450;
1092                         break;
1093                 case 1:
1094                         up->port.type = PORT_UNKNOWN;
1095                         break;
1096                 case 2:
1097                         up->port.type = PORT_16550;
1098                         break;
1099                 case 3:
1100                         up->port.type = PORT_16550A;
1101                         break;
1102         }
1103         if (up->port.type == PORT_16550A) {
1104                 /* Check for Startech UART's */
1105                 serial_outp(up, UART_LCR, UART_LCR_DLAB);
1106                 if (serial_in(up, UART_EFR) == 0) {
1107                         up->port.type = PORT_16650;
1108                 } else {
1109                         serial_outp(up, UART_LCR, 0xBF);
1110                         if (serial_in(up, UART_EFR) == 0)
1111                                 up->port.type = PORT_16650V2;
1112                 }
1113         }
1114         if (up->port.type == PORT_16550A) {
1115                 /* Check for TI 16750 */
1116                 serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
1117                 serial_outp(up, UART_FCR,
1118                             UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1119                 scratch = serial_in(up, UART_IIR) >> 5;
1120                 if (scratch == 7) {
1121                         /*
1122                          * If this is a 16750, and not a cheap UART
1123                          * clone, then it should only go into 64 byte
1124                          * mode if the UART_FCR7_64BYTE bit was set
1125                          * while UART_LCR_DLAB was latched.
1126                          */
1127                         serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1128                         serial_outp(up, UART_LCR, 0);
1129                         serial_outp(up, UART_FCR,
1130                                     UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
1131                         scratch = serial_in(up, UART_IIR) >> 5;
1132                         if (scratch == 6)
1133                                 up->port.type = PORT_16750;
1134                 }
1135                 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
1136         }
1137         serial_outp(up, UART_LCR, save_lcr);
1138         if (up->port.type == PORT_16450) {
1139                 scratch = serial_in(up, UART_SCR);
1140                 serial_outp(up, UART_SCR, 0xa5);
1141                 status1 = serial_in(up, UART_SCR);
1142                 serial_outp(up, UART_SCR, 0x5a);
1143                 status2 = serial_in(up, UART_SCR);
1144                 serial_outp(up, UART_SCR, scratch);
1145
1146                 if ((status1 != 0xa5) || (status2 != 0x5a))
1147                         up->port.type = PORT_8250;
1148         }
1149
1150         up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;
1151
1152         if (up->port.type == PORT_UNKNOWN)
1153                 goto out;
1154         up->type_probed = up->port.type;        /* XXX */
1155
1156         /*
1157          * Reset the UART.
1158          */
1159 #ifdef CONFIG_SERIAL_8250_RSA
1160         if (up->port.type == PORT_RSA)
1161                 serial_outp(up, UART_RSA_FRR, 0);
1162 #endif
1163         serial_outp(up, UART_MCR, save_mcr);
1164         serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
1165                                      UART_FCR_CLEAR_RCVR |
1166                                      UART_FCR_CLEAR_XMIT));
1167         serial_outp(up, UART_FCR, 0);
1168         (void)serial_in(up, UART_RX);
1169         serial_outp(up, UART_IER, 0);
1170
1171 out:
1172         spin_unlock_irqrestore(&up->port.lock, flags);
1173 }
1174
1175 static struct uart_driver sunsu_reg = {
1176         .owner                  = THIS_MODULE,
1177         .driver_name            = "sunsu",
1178         .dev_name               = "ttyS",
1179         .major                  = TTY_MAJOR,
1180 };
1181
1182 static int __devinit sunsu_kbd_ms_init(struct uart_sunsu_port *up)
1183 {
1184         int quot, baud;
1185 #ifdef CONFIG_SERIO
1186         struct serio *serio;
1187 #endif
1188
1189         if (up->su_type == SU_PORT_KBD) {
1190                 up->cflag = B1200 | CS8 | CLOCAL | CREAD;
1191                 baud = 1200;
1192         } else {
1193                 up->cflag = B4800 | CS8 | CLOCAL | CREAD;
1194                 baud = 4800;
1195         }
1196         quot = up->port.uartclk / (16 * baud);
1197
1198         sunsu_autoconfig(up);
1199         if (up->port.type == PORT_UNKNOWN)
1200                 return -ENODEV;
1201
1202         printk("%s: %s port at %llx, irq %u\n",
1203                up->port.dev->of_node->full_name,
1204                (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse",
1205                (unsigned long long) up->port.mapbase,
1206                up->port.irq);
1207
1208 #ifdef CONFIG_SERIO
1209         serio = &up->serio;
1210         serio->port_data = up;
1211
1212         serio->id.type = SERIO_RS232;
1213         if (up->su_type == SU_PORT_KBD) {
1214                 serio->id.proto = SERIO_SUNKBD;
1215                 strlcpy(serio->name, "sukbd", sizeof(serio->name));
1216         } else {
1217                 serio->id.proto = SERIO_SUN;
1218                 serio->id.extra = 1;
1219                 strlcpy(serio->name, "sums", sizeof(serio->name));
1220         }
1221         strlcpy(serio->phys,
1222                 (!(up->port.line & 1) ? "su/serio0" : "su/serio1"),
1223                 sizeof(serio->phys));
1224
1225         serio->write = sunsu_serio_write;
1226         serio->open = sunsu_serio_open;
1227         serio->close = sunsu_serio_close;
1228         serio->dev.parent = up->port.dev;
1229
1230         serio_register_port(serio);
1231 #endif
1232
1233         sunsu_change_speed(&up->port, up->cflag, 0, quot);
1234
1235         sunsu_startup(&up->port);
1236         return 0;
1237 }
1238
1239 /*
1240  * ------------------------------------------------------------
1241  * Serial console driver
1242  * ------------------------------------------------------------
1243  */
1244
1245 #ifdef CONFIG_SERIAL_SUNSU_CONSOLE
1246
1247 #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
1248
1249 /*
1250  *      Wait for transmitter & holding register to empty
1251  */
1252 static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up)
1253 {
1254         unsigned int status, tmout = 10000;
1255
1256         /* Wait up to 10ms for the character(s) to be sent. */
1257         do {
1258                 status = serial_in(up, UART_LSR);
1259
1260                 if (status & UART_LSR_BI)
1261                         up->lsr_break_flag = UART_LSR_BI;
1262
1263                 if (--tmout == 0)
1264                         break;
1265                 udelay(1);
1266         } while ((status & BOTH_EMPTY) != BOTH_EMPTY);
1267
1268         /* Wait up to 1s for flow control if necessary */
1269         if (up->port.flags & UPF_CONS_FLOW) {
1270                 tmout = 1000000;
1271                 while (--tmout &&
1272                        ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
1273                         udelay(1);
1274         }
1275 }
1276
1277 static void sunsu_console_putchar(struct uart_port *port, int ch)
1278 {
1279         struct uart_sunsu_port *up = (struct uart_sunsu_port *)port;
1280
1281         wait_for_xmitr(up);
1282         serial_out(up, UART_TX, ch);
1283 }
1284
1285 /*
1286  *      Print a string to the serial port trying not to disturb
1287  *      any possible real use of the port...
1288  */
1289 static void sunsu_console_write(struct console *co, const char *s,
1290                                 unsigned int count)
1291 {
1292         struct uart_sunsu_port *up = &sunsu_ports[co->index];
1293         unsigned long flags;
1294         unsigned int ier;
1295         int locked = 1;
1296
1297         local_irq_save(flags);
1298         if (up->port.sysrq) {
1299                 locked = 0;
1300         } else if (oops_in_progress) {
1301                 locked = spin_trylock(&up->port.lock);
1302         } else
1303                 spin_lock(&up->port.lock);
1304
1305         /*
1306          *      First save the UER then disable the interrupts
1307          */
1308         ier = serial_in(up, UART_IER);
1309         serial_out(up, UART_IER, 0);
1310
1311         uart_console_write(&up->port, s, count, sunsu_console_putchar);
1312
1313         /*
1314          *      Finally, wait for transmitter to become empty
1315          *      and restore the IER
1316          */
1317         wait_for_xmitr(up);
1318         serial_out(up, UART_IER, ier);
1319
1320         if (locked)
1321                 spin_unlock(&up->port.lock);
1322         local_irq_restore(flags);
1323 }
1324
1325 /*
1326  *      Setup initial baud/bits/parity. We do two things here:
1327  *      - construct a cflag setting for the first su_open()
1328  *      - initialize the serial port
1329  *      Return non-zero if we didn't find a serial port.
1330  */
1331 static int __init sunsu_console_setup(struct console *co, char *options)
1332 {
1333         static struct ktermios dummy;
1334         struct ktermios termios;
1335         struct uart_port *port;
1336
1337         printk("Console: ttyS%d (SU)\n",
1338                (sunsu_reg.minor - 64) + co->index);
1339
1340         /*
1341          * Check whether an invalid uart number has been specified, and
1342          * if so, search for the first available port that does have
1343          * console support.
1344          */
1345         if (co->index >= UART_NR)
1346                 co->index = 0;
1347         port = &sunsu_ports[co->index].port;
1348
1349         /*
1350          * Temporary fix.
1351          */
1352         spin_lock_init(&port->lock);
1353
1354         /* Get firmware console settings.  */
1355         sunserial_console_termios(co, port->dev->of_node);
1356
1357         memset(&termios, 0, sizeof(struct ktermios));
1358         termios.c_cflag = co->cflag;
1359         port->mctrl |= TIOCM_DTR;
1360         port->ops->set_termios(port, &termios, &dummy);
1361
1362         return 0;
1363 }
1364
1365 static struct console sunsu_console = {
1366         .name   =       "ttyS",
1367         .write  =       sunsu_console_write,
1368         .device =       uart_console_device,
1369         .setup  =       sunsu_console_setup,
1370         .flags  =       CON_PRINTBUFFER,
1371         .index  =       -1,
1372         .data   =       &sunsu_reg,
1373 };
1374
1375 /*
1376  *      Register console.
1377  */
1378
1379 static inline struct console *SUNSU_CONSOLE(void)
1380 {
1381         return &sunsu_console;
1382 }
1383 #else
1384 #define SUNSU_CONSOLE()                 (NULL)
1385 #define sunsu_serial_console_init()     do { } while (0)
1386 #endif
1387
1388 static enum su_type __devinit su_get_type(struct device_node *dp)
1389 {
1390         struct device_node *ap = of_find_node_by_path("/aliases");
1391
1392         if (ap) {
1393                 const char *keyb = of_get_property(ap, "keyboard", NULL);
1394                 const char *ms = of_get_property(ap, "mouse", NULL);
1395
1396                 if (keyb) {
1397                         if (dp == of_find_node_by_path(keyb))
1398                                 return SU_PORT_KBD;
1399                 }
1400                 if (ms) {
1401                         if (dp == of_find_node_by_path(ms))
1402                                 return SU_PORT_MS;
1403                 }
1404         }
1405
1406         return SU_PORT_PORT;
1407 }
1408
1409 static int __devinit su_probe(struct platform_device *op)
1410 {
1411         static int inst;
1412         struct device_node *dp = op->dev.of_node;
1413         struct uart_sunsu_port *up;
1414         struct resource *rp;
1415         enum su_type type;
1416         bool ignore_line;
1417         int err;
1418
1419         type = su_get_type(dp);
1420         if (type == SU_PORT_PORT) {
1421                 if (inst >= UART_NR)
1422                         return -EINVAL;
1423                 up = &sunsu_ports[inst];
1424         } else {
1425                 up = kzalloc(sizeof(*up), GFP_KERNEL);
1426                 if (!up)
1427                         return -ENOMEM;
1428         }
1429
1430         up->port.line = inst;
1431
1432         spin_lock_init(&up->port.lock);
1433
1434         up->su_type = type;
1435
1436         rp = &op->resource[0];
1437         up->port.mapbase = rp->start;
1438         up->reg_size = resource_size(rp);
1439         up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
1440         if (!up->port.membase) {
1441                 if (type != SU_PORT_PORT)
1442                         kfree(up);
1443                 return -ENOMEM;
1444         }
1445
1446         up->port.irq = op->archdata.irqs[0];
1447
1448         up->port.dev = &op->dev;
1449
1450         up->port.type = PORT_UNKNOWN;
1451         up->port.uartclk = (SU_BASE_BAUD * 16);
1452
1453         err = 0;
1454         if (up->su_type == SU_PORT_KBD || up->su_type == SU_PORT_MS) {
1455                 err = sunsu_kbd_ms_init(up);
1456                 if (err) {
1457                         of_iounmap(&op->resource[0],
1458                                    up->port.membase, up->reg_size);
1459                         kfree(up);
1460                         return err;
1461                 }
1462                 dev_set_drvdata(&op->dev, up);
1463
1464                 return 0;
1465         }
1466
1467         up->port.flags |= UPF_BOOT_AUTOCONF;
1468
1469         sunsu_autoconfig(up);
1470
1471         err = -ENODEV;
1472         if (up->port.type == PORT_UNKNOWN)
1473                 goto out_unmap;
1474
1475         up->port.ops = &sunsu_pops;
1476
1477         ignore_line = false;
1478         if (!strcmp(dp->name, "rsc-console") ||
1479             !strcmp(dp->name, "lom-console"))
1480                 ignore_line = true;
1481
1482         sunserial_console_match(SUNSU_CONSOLE(), dp,
1483                                 &sunsu_reg, up->port.line,
1484                                 ignore_line);
1485         err = uart_add_one_port(&sunsu_reg, &up->port);
1486         if (err)
1487                 goto out_unmap;
1488
1489         dev_set_drvdata(&op->dev, up);
1490
1491         inst++;
1492
1493         return 0;
1494
1495 out_unmap:
1496         of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1497         return err;
1498 }
1499
1500 static int __devexit su_remove(struct platform_device *op)
1501 {
1502         struct uart_sunsu_port *up = dev_get_drvdata(&op->dev);
1503         bool kbdms = false;
1504
1505         if (up->su_type == SU_PORT_MS ||
1506             up->su_type == SU_PORT_KBD)
1507                 kbdms = true;
1508
1509         if (kbdms) {
1510 #ifdef CONFIG_SERIO
1511                 serio_unregister_port(&up->serio);
1512 #endif
1513         } else if (up->port.type != PORT_UNKNOWN)
1514                 uart_remove_one_port(&sunsu_reg, &up->port);
1515
1516         if (up->port.membase)
1517                 of_iounmap(&op->resource[0], up->port.membase, up->reg_size);
1518
1519         if (kbdms)
1520                 kfree(up);
1521
1522         dev_set_drvdata(&op->dev, NULL);
1523
1524         return 0;
1525 }
1526
1527 static const struct of_device_id su_match[] = {
1528         {
1529                 .name = "su",
1530         },
1531         {
1532                 .name = "su_pnp",
1533         },
1534         {
1535                 .name = "serial",
1536                 .compatible = "su",
1537         },
1538         {
1539                 .type = "serial",
1540                 .compatible = "su",
1541         },
1542         {},
1543 };
1544 MODULE_DEVICE_TABLE(of, su_match);
1545
1546 static struct platform_driver su_driver = {
1547         .driver = {
1548                 .name = "su",
1549                 .owner = THIS_MODULE,
1550                 .of_match_table = su_match,
1551         },
1552         .probe          = su_probe,
1553         .remove         = __devexit_p(su_remove),
1554 };
1555
1556 static int __init sunsu_init(void)
1557 {
1558         struct device_node *dp;
1559         int err;
1560         int num_uart = 0;
1561
1562         for_each_node_by_name(dp, "su") {
1563                 if (su_get_type(dp) == SU_PORT_PORT)
1564                         num_uart++;
1565         }
1566         for_each_node_by_name(dp, "su_pnp") {
1567                 if (su_get_type(dp) == SU_PORT_PORT)
1568                         num_uart++;
1569         }
1570         for_each_node_by_name(dp, "serial") {
1571                 if (of_device_is_compatible(dp, "su")) {
1572                         if (su_get_type(dp) == SU_PORT_PORT)
1573                                 num_uart++;
1574                 }
1575         }
1576         for_each_node_by_type(dp, "serial") {
1577                 if (of_device_is_compatible(dp, "su")) {
1578                         if (su_get_type(dp) == SU_PORT_PORT)
1579                                 num_uart++;
1580                 }
1581         }
1582
1583         if (num_uart) {
1584                 err = sunserial_register_minors(&sunsu_reg, num_uart);
1585                 if (err)
1586                         return err;
1587         }
1588
1589         err = platform_driver_register(&su_driver);
1590         if (err && num_uart)
1591                 sunserial_unregister_minors(&sunsu_reg, num_uart);
1592
1593         return err;
1594 }
1595
1596 static void __exit sunsu_exit(void)
1597 {
1598         if (sunsu_reg.nr)
1599                 sunserial_unregister_minors(&sunsu_reg, sunsu_reg.nr);
1600 }
1601
1602 module_init(sunsu_init);
1603 module_exit(sunsu_exit);
1604
1605 MODULE_AUTHOR("Eddie C. Dost, Peter Zaitcev, and David S. Miller");
1606 MODULE_DESCRIPTION("Sun SU serial port driver");
1607 MODULE_VERSION("2.0");
1608 MODULE_LICENSE("GPL");