drivers/power/smb347-charger.c

   1 /*
   2  * Summit Microelectronics SMB347 Battery Charger Driver
   3  *
   4  * Copyright (C) 2011, Intel Corporation
   5  *
   6  * Authors: Bruce E. Robertson <bruce.e.robertson@intel.com>
   7  *          Mika Westerberg <mika.westerberg@linux.intel.com>
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  */
  13
  14 #include <linux/err.h>
  15 #include <linux/gpio.h>
  16 #include <linux/kernel.h>
  17 #include <linux/module.h>
  18 #include <linux/init.h>
  19 #include <linux/interrupt.h>
  20 #include <linux/i2c.h>
  21 #include <linux/mutex.h>
  22 #include <linux/power_supply.h>
  23 #include <linux/power/smb347-charger.h>
  24 #include <linux/regmap.h>
  25
  26 /*
  27  * Configuration registers. These are mirrored to volatile RAM and can be
  28  * written once %CMD_A_ALLOW_WRITE is set in %CMD_A register. They will be
  29  * reloaded from non-volatile registers after POR.
  30  */
  31 #define CFG_CHARGE_CURRENT                      0x00
  32 #define CFG_CHARGE_CURRENT_FCC_MASK             0xe0
  33 #define CFG_CHARGE_CURRENT_FCC_SHIFT            5
  34 #define CFG_CHARGE_CURRENT_PCC_MASK             0x18
  35 #define CFG_CHARGE_CURRENT_PCC_SHIFT            3
  36 #define CFG_CHARGE_CURRENT_TC_MASK              0x07
  37 #define CFG_CURRENT_LIMIT                       0x01
  38 #define CFG_CURRENT_LIMIT_DC_MASK               0xf0
  39 #define CFG_CURRENT_LIMIT_DC_SHIFT              4
  40 #define CFG_CURRENT_LIMIT_USB_MASK              0x0f
  41 #define CFG_FLOAT_VOLTAGE                       0x03
  42 #define CFG_FLOAT_VOLTAGE_FLOAT_MASK            0x3f
  43 #define CFG_FLOAT_VOLTAGE_THRESHOLD_MASK        0xc0
  44 #define CFG_FLOAT_VOLTAGE_THRESHOLD_SHIFT       6
  45 #define CFG_STAT                                0x05
  46 #define CFG_STAT_DISABLED                       BIT(5)
  47 #define CFG_STAT_ACTIVE_HIGH                    BIT(7)
  48 #define CFG_PIN                                 0x06
  49 #define CFG_PIN_EN_CTRL_MASK                    0x60
  50 #define CFG_PIN_EN_CTRL_ACTIVE_HIGH             0x40
  51 #define CFG_PIN_EN_CTRL_ACTIVE_LOW              0x60
  52 #define CFG_PIN_EN_APSD_IRQ                     BIT(1)
  53 #define CFG_PIN_EN_CHARGER_ERROR                BIT(2)
  54 #define CFG_THERM                               0x07
  55 #define CFG_THERM_SOFT_HOT_COMPENSATION_MASK    0x03
  56 #define CFG_THERM_SOFT_HOT_COMPENSATION_SHIFT   0
  57 #define CFG_THERM_SOFT_COLD_COMPENSATION_MASK   0x0c
  58 #define CFG_THERM_SOFT_COLD_COMPENSATION_SHIFT  2
  59 #define CFG_THERM_MONITOR_DISABLED              BIT(4)
  60 #define CFG_SYSOK                               0x08
  61 #define CFG_SYSOK_SUSPEND_HARD_LIMIT_DISABLED   BIT(2)
  62 #define CFG_OTHER                               0x09
  63 #define CFG_OTHER_RID_MASK                      0xc0
  64 #define CFG_OTHER_RID_ENABLED_AUTO_OTG          0xc0
  65 #define CFG_OTG                                 0x0a
  66 #define CFG_OTG_TEMP_THRESHOLD_MASK             0x30
  67 #define CFG_OTG_TEMP_THRESHOLD_SHIFT            4
  68 #define CFG_OTG_CC_COMPENSATION_MASK            0xc0
  69 #define CFG_OTG_CC_COMPENSATION_SHIFT           6
  70 #define CFG_TEMP_LIMIT                          0x0b
  71 #define CFG_TEMP_LIMIT_SOFT_HOT_MASK            0x03
  72 #define CFG_TEMP_LIMIT_SOFT_HOT_SHIFT           0
  73 #define CFG_TEMP_LIMIT_SOFT_COLD_MASK           0x0c
  74 #define CFG_TEMP_LIMIT_SOFT_COLD_SHIFT          2
  75 #define CFG_TEMP_LIMIT_HARD_HOT_MASK            0x30
  76 #define CFG_TEMP_LIMIT_HARD_HOT_SHIFT           4
  77 #define CFG_TEMP_LIMIT_HARD_COLD_MASK           0xc0
  78 #define CFG_TEMP_LIMIT_HARD_COLD_SHIFT          6
  79 #define CFG_FAULT_IRQ                           0x0c
  80 #define CFG_FAULT_IRQ_DCIN_UV                   BIT(2)
  81 #define CFG_STATUS_IRQ                          0x0d
  82 #define CFG_STATUS_IRQ_TERMINATION_OR_TAPER     BIT(4)
  83 #define CFG_ADDRESS                             0x0e
  84
  85 /* Command registers */
  86 #define CMD_A                                   0x30
  87 #define CMD_A_CHG_ENABLED                       BIT(1)
  88 #define CMD_A_SUSPEND_ENABLED                   BIT(2)
  89 #define CMD_A_ALLOW_WRITE                       BIT(7)
  90 #define CMD_B                                   0x31
  91 #define CMD_C                                   0x33
  92
  93 /* Interrupt Status registers */
  94 #define IRQSTAT_A                               0x35
  95 #define IRQSTAT_C                               0x37
  96 #define IRQSTAT_C_TERMINATION_STAT              BIT(0)
  97 #define IRQSTAT_C_TERMINATION_IRQ               BIT(1)
  98 #define IRQSTAT_C_TAPER_IRQ                     BIT(3)
  99 #define IRQSTAT_E                               0x39
 100 #define IRQSTAT_E_USBIN_UV_STAT                 BIT(0)
 101 #define IRQSTAT_E_USBIN_UV_IRQ                  BIT(1)
 102 #define IRQSTAT_E_DCIN_UV_STAT                  BIT(4)
 103 #define IRQSTAT_E_DCIN_UV_IRQ                   BIT(5)
 104 #define IRQSTAT_F                               0x3a
 105
 106 /* Status registers */
 107 #define STAT_A                                  0x3b
 108 #define STAT_A_FLOAT_VOLTAGE_MASK               0x3f
 109 #define STAT_B                                  0x3c
 110 #define STAT_C                                  0x3d
 111 #define STAT_C_CHG_ENABLED                      BIT(0)
 112 #define STAT_C_CHG_MASK                         0x06
 113 #define STAT_C_CHG_SHIFT                        1
 114 #define STAT_C_CHARGER_ERROR                    BIT(6)
 115 #define STAT_E                                  0x3f
 116
 117 #define SMB347_MAX_REGISTER                     0x3f
 118
 119 /**
 120  * struct smb347_charger - smb347 charger instance
 121  * @lock: protects concurrent access to online variables
 122  * @dev: pointer to device
 123  * @regmap: pointer to driver regmap
 124  * @mains: power_supply instance for AC/DC power
 125  * @usb: power_supply instance for USB power
 126  * @battery: power_supply instance for battery
 127  * @mains_online: is AC/DC input connected
 128  * @usb_online: is USB input connected
 129  * @charging_enabled: is charging enabled
 130  * @pdata: pointer to platform data
 131  */
 132 struct smb347_charger {
 133         struct mutex            lock;
 134         struct device           *dev;
 135         struct regmap           *regmap;
 136         struct power_supply     mains;
 137         struct power_supply     usb;
 138         struct power_supply     battery;
 139         bool                    mains_online;
 140         bool                    usb_online;
 141         bool                    charging_enabled;
 142         const struct smb347_charger_platform_data *pdata;
 143 };
 144
 145 /* Fast charge current in uA */
 146 static const unsigned int fcc_tbl[] = {
 147         700000,
 148         900000,
 149         1200000,
 150         1500000,
 151         1800000,
 152         2000000,
 153         2200000,
 154         2500000,
 155 };
 156
 157 /* Pre-charge current in uA */
 158 static const unsigned int pcc_tbl[] = {
 159         100000,
 160         150000,
 161         200000,
 162         250000,
 163 };
 164
 165 /* Termination current in uA */
 166 static const unsigned int tc_tbl[] = {
 167         37500,
 168         50000,
 169         100000,
 170         150000,
 171         200000,
 172         250000,
 173         500000,
 174         600000,
 175 };
 176
 177 /* Input current limit in uA */
 178 static const unsigned int icl_tbl[] = {
 179         300000,
 180         500000,
 181         700000,
 182         900000,
 183         1200000,
 184         1500000,
 185         1800000,
 186         2000000,
 187         2200000,
 188         2500000,
 189 };
 190
 191 /* Charge current compensation in uA */
 192 static const unsigned int ccc_tbl[] = {
 193         250000,
 194         700000,
 195         900000,
 196         1200000,
 197 };
 198
 199 /* Convert register value to current using lookup table */
 200 static int hw_to_current(const unsigned int *tbl, size_t size, unsigned int val)
 201 {
 202         if (val >= size)
 203                 return -EINVAL;
 204         return tbl[val];
 205 }
 206
 207 /* Convert current to register value using lookup table */
 208 static int current_to_hw(const unsigned int *tbl, size_t size, unsigned int val)
 209 {
 210         size_t i;
 211
 212         for (i = 0; i < size; i++)
 213                 if (val < tbl[i])
 214                         break;
 215         return i > 0 ? i - 1 : -EINVAL;
 216 }
 217
 218 /**
 219  * smb347_update_ps_status - refreshes the power source status
 220  * @smb: pointer to smb347 charger instance
 221  *
 222  * Function checks whether any power source is connected to the charger and
 223  * updates internal state accordingly. If there is a change to previous state
 224  * function returns %1, otherwise %0 and negative errno in case of errror.
 225  */
 226 static int smb347_update_ps_status(struct smb347_charger *smb)
 227 {
 228         bool usb = false;
 229         bool dc = false;
 230         unsigned int val;
 231         int ret;
 232
 233         ret = regmap_read(smb->regmap, IRQSTAT_E, &val);
 234         if (ret < 0)
 235                 return ret;
 236
 237         /*
 238          * Dc and usb are set depending on whether they are enabled in
 239          * platform data _and_ whether corresponding undervoltage is set.
 240          */
 241         if (smb->pdata->use_mains)
 242                 dc = !(val & IRQSTAT_E_DCIN_UV_STAT);
 243         if (smb->pdata->use_usb)
 244                 usb = !(val & IRQSTAT_E_USBIN_UV_STAT);
 245
 246         mutex_lock(&smb->lock);
 247         ret = smb->mains_online != dc || smb->usb_online != usb;
 248         smb->mains_online = dc;
 249         smb->usb_online = usb;
 250         mutex_unlock(&smb->lock);
 251
 252         return ret;
 253 }
 254
 255 /*
 256  * smb347_is_ps_online - returns whether input power source is connected
 257  * @smb: pointer to smb347 charger instance
 258  *
 259  * Returns %true if input power source is connected. Note that this is
 260  * dependent on what platform has configured for usable power sources. For
 261  * example if USB is disabled, this will return %false even if the USB cable
 262  * is connected.
 263  */
 264 static bool smb347_is_ps_online(struct smb347_charger *smb)
 265 {
 266         bool ret;
 267
 268         mutex_lock(&smb->lock);
 269         ret = smb->usb_online || smb->mains_online;
 270         mutex_unlock(&smb->lock);
 271
 272         return ret;
 273 }
 274
 275 /**
 276  * smb347_charging_status - returns status of charging
 277  * @smb: pointer to smb347 charger instance
 278  *
 279  * Function returns charging status. %0 means no charging is in progress,
 280  * %1 means pre-charging, %2 fast-charging and %3 taper-charging.
 281  */
 282 static int smb347_charging_status(struct smb347_charger *smb)
 283 {
 284         unsigned int val;
 285         int ret;
 286
 287         if (!smb347_is_ps_online(smb))
 288                 return 0;
 289
 290         ret = regmap_read(smb->regmap, STAT_C, &val);
 291         if (ret < 0)
 292                 return 0;
 293
 294         return (val & STAT_C_CHG_MASK) >> STAT_C_CHG_SHIFT;
 295 }
 296
 297 static int smb347_charging_set(struct smb347_charger *smb, bool enable)
 298 {
 299         int ret = 0;
 300
 301         if (smb->pdata->enable_control != SMB347_CHG_ENABLE_SW) {
 302                 dev_dbg(smb->dev, "charging enable/disable in SW disabled\n");
 303                 return 0;
 304         }
 305
 306         mutex_lock(&smb->lock);
 307         if (smb->charging_enabled != enable) {
 308                 ret = regmap_update_bits(smb->regmap, CMD_A, CMD_A_CHG_ENABLED,
 309                                          enable ? CMD_A_CHG_ENABLED : 0);
 310                 if (!ret)
 311                         smb->charging_enabled = enable;
 312         }
 313         mutex_unlock(&smb->lock);
 314         return ret;
 315 }
 316
 317 static inline int smb347_charging_enable(struct smb347_charger *smb)
 318 {
 319         return smb347_charging_set(smb, true);
 320 }
 321
 322 static inline int smb347_charging_disable(struct smb347_charger *smb)
 323 {
 324         return smb347_charging_set(smb, false);
 325 }
 326
 327 static int smb347_start_stop_charging(struct smb347_charger *smb)
 328 {
 329         int ret;
 330
 331         /*
 332          * Depending on whether valid power source is connected or not, we
 333          * disable or enable the charging. We do it manually because it
 334          * depends on how the platform has configured the valid inputs.
 335          */
 336         if (smb347_is_ps_online(smb)) {
 337                 ret = smb347_charging_enable(smb);
 338                 if (ret < 0)
 339                         dev_err(smb->dev, "failed to enable charging\n");
 340         } else {
 341                 ret = smb347_charging_disable(smb);
 342                 if (ret < 0)
 343                         dev_err(smb->dev, "failed to disable charging\n");
 344         }
 345
 346         return ret;
 347 }
 348
 349 static int smb347_set_charge_current(struct smb347_charger *smb)
 350 {
 351         int ret;
 352
 353         if (smb->pdata->max_charge_current) {
 354                 ret = current_to_hw(fcc_tbl, ARRAY_SIZE(fcc_tbl),
 355                                     smb->pdata->max_charge_current);
 356                 if (ret < 0)
 357                         return ret;
 358
 359                 ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
 360                                          CFG_CHARGE_CURRENT_FCC_MASK,
 361                                          ret << CFG_CHARGE_CURRENT_FCC_SHIFT);
 362                 if (ret < 0)
 363                         return ret;
 364         }
 365
 366         if (smb->pdata->pre_charge_current) {
 367                 ret = current_to_hw(pcc_tbl, ARRAY_SIZE(pcc_tbl),
 368                                     smb->pdata->pre_charge_current);
 369                 if (ret < 0)
 370                         return ret;
 371
 372                 ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
 373                                          CFG_CHARGE_CURRENT_PCC_MASK,
 374                                          ret << CFG_CHARGE_CURRENT_PCC_SHIFT);
 375                 if (ret < 0)
 376                         return ret;
 377         }
 378
 379         if (smb->pdata->termination_current) {
 380                 ret = current_to_hw(tc_tbl, ARRAY_SIZE(tc_tbl),
 381                                     smb->pdata->termination_current);
 382                 if (ret < 0)
 383                         return ret;
 384
 385                 ret = regmap_update_bits(smb->regmap, CFG_CHARGE_CURRENT,
 386                                          CFG_CHARGE_CURRENT_TC_MASK, ret);
 387                 if (ret < 0)
 388                         return ret;
 389         }
 390
 391         return 0;
 392 }
 393
 394 static int smb347_set_current_limits(struct smb347_charger *smb)
 395 {
 396         int ret;
 397
 398         if (smb->pdata->mains_current_limit) {
 399                 ret = current_to_hw(icl_tbl, ARRAY_SIZE(icl_tbl),
 400                                     smb->pdata->mains_current_limit);
 401                 if (ret < 0)
 402                         return ret;
 403
 404                 ret = regmap_update_bits(smb->regmap, CFG_CURRENT_LIMIT,
 405                                          CFG_CURRENT_LIMIT_DC_MASK,
 406                                          ret << CFG_CURRENT_LIMIT_DC_SHIFT);
 407                 if (ret < 0)
 408                         return ret;
 409         }
 410
 411         if (smb->pdata->usb_hc_current_limit) {
 412                 ret = current_to_hw(icl_tbl, ARRAY_SIZE(icl_tbl),
 413                                     smb->pdata->usb_hc_current_limit);
 414                 if (ret < 0)
 415                         return ret;
 416
 417                 ret = regmap_update_bits(smb->regmap, CFG_CURRENT_LIMIT,
 418                                          CFG_CURRENT_LIMIT_USB_MASK, ret);
 419                 if (ret < 0)
 420                         return ret;
 421         }
 422
 423         return 0;
 424 }
 425
 426 static int smb347_set_voltage_limits(struct smb347_charger *smb)
 427 {
 428         int ret;
 429
 430         if (smb->pdata->pre_to_fast_voltage) {
 431                 ret = smb->pdata->pre_to_fast_voltage;
 432
 433                 /* uV */
 434                 ret = clamp_val(ret, 2400000, 3000000) - 2400000;
 435                 ret /= 200000;
 436
 437                 ret = regmap_update_bits(smb->regmap, CFG_FLOAT_VOLTAGE,
 438                                 CFG_FLOAT_VOLTAGE_THRESHOLD_MASK,
 439                                 ret << CFG_FLOAT_VOLTAGE_THRESHOLD_SHIFT);
 440                 if (ret < 0)
 441                         return ret;
 442         }
 443
 444         if (smb->pdata->max_charge_voltage) {
 445                 ret = smb->pdata->max_charge_voltage;
 446
 447                 /* uV */
 448                 ret = clamp_val(ret, 3500000, 4500000) - 3500000;
 449                 ret /= 20000;
 450
 451                 ret = regmap_update_bits(smb->regmap, CFG_FLOAT_VOLTAGE,
 452                                          CFG_FLOAT_VOLTAGE_FLOAT_MASK, ret);
 453                 if (ret < 0)
 454                         return ret;
 455         }
 456
 457         return 0;
 458 }
 459
 460 static int smb347_set_temp_limits(struct smb347_charger *smb)
 461 {
 462         bool enable_therm_monitor = false;
 463         int ret = 0;
 464         int val;
 465
 466         if (smb->pdata->chip_temp_threshold) {
 467                 val = smb->pdata->chip_temp_threshold;
 468
 469                 /* degree C */
 470                 val = clamp_val(val, 100, 130) - 100;
 471                 val /= 10;
 472
 473                 ret = regmap_update_bits(smb->regmap, CFG_OTG,
 474                                          CFG_OTG_TEMP_THRESHOLD_MASK,
 475                                          val << CFG_OTG_TEMP_THRESHOLD_SHIFT);
 476                 if (ret < 0)
 477                         return ret;
 478         }
 479
 480         if (smb->pdata->soft_cold_temp_limit != SMB347_TEMP_USE_DEFAULT) {
 481                 val = smb->pdata->soft_cold_temp_limit;
 482
 483                 val = clamp_val(val, 0, 15);
 484                 val /= 5;
 485                 /* this goes from higher to lower so invert the value */
 486                 val = ~val & 0x3;
 487
 488                 ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
 489                                          CFG_TEMP_LIMIT_SOFT_COLD_MASK,
 490                                          val << CFG_TEMP_LIMIT_SOFT_COLD_SHIFT);
 491                 if (ret < 0)
 492                         return ret;
 493
 494                 enable_therm_monitor = true;
 495         }
 496
 497         if (smb->pdata->soft_hot_temp_limit != SMB347_TEMP_USE_DEFAULT) {
 498                 val = smb->pdata->soft_hot_temp_limit;
 499
 500                 val = clamp_val(val, 40, 55) - 40;
 501                 val /= 5;
 502
 503                 ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
 504                                          CFG_TEMP_LIMIT_SOFT_HOT_MASK,
 505                                          val << CFG_TEMP_LIMIT_SOFT_HOT_SHIFT);
 506                 if (ret < 0)
 507                         return ret;
 508
 509                 enable_therm_monitor = true;
 510         }
 511
 512         if (smb->pdata->hard_cold_temp_limit != SMB347_TEMP_USE_DEFAULT) {
 513                 val = smb->pdata->hard_cold_temp_limit;
 514
 515                 val = clamp_val(val, -5, 10) + 5;
 516                 val /= 5;
 517                 /* this goes from higher to lower so invert the value */
 518                 val = ~val & 0x3;
 519
 520                 ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
 521                                          CFG_TEMP_LIMIT_HARD_COLD_MASK,
 522                                          val << CFG_TEMP_LIMIT_HARD_COLD_SHIFT);
 523                 if (ret < 0)
 524                         return ret;
 525
 526                 enable_therm_monitor = true;
 527         }
 528
 529         if (smb->pdata->hard_hot_temp_limit != SMB347_TEMP_USE_DEFAULT) {
 530                 val = smb->pdata->hard_hot_temp_limit;
 531
 532                 val = clamp_val(val, 50, 65) - 50;
 533                 val /= 5;
 534
 535                 ret = regmap_update_bits(smb->regmap, CFG_TEMP_LIMIT,
 536                                          CFG_TEMP_LIMIT_HARD_HOT_MASK,
 537                                          val << CFG_TEMP_LIMIT_HARD_HOT_SHIFT);
 538                 if (ret < 0)
 539                         return ret;
 540
 541                 enable_therm_monitor = true;
 542         }
 543
 544         /*
 545          * If any of the temperature limits are set, we also enable the
 546          * thermistor monitoring.
 547          *
 548          * When soft limits are hit, the device will start to compensate
 549          * current and/or voltage depending on the configuration.
 550          *
 551          * When hard limit is hit, the device will suspend charging
 552          * depending on the configuration.
 553          */
 554         if (enable_therm_monitor) {
 555                 ret = regmap_update_bits(smb->regmap, CFG_THERM,
 556                                          CFG_THERM_MONITOR_DISABLED, 0);
 557                 if (ret < 0)
 558                         return ret;
 559         }
 560
 561         if (smb->pdata->suspend_on_hard_temp_limit) {
 562                 ret = regmap_update_bits(smb->regmap, CFG_SYSOK,
 563                                  CFG_SYSOK_SUSPEND_HARD_LIMIT_DISABLED, 0);
 564                 if (ret < 0)
 565                         return ret;
 566         }
 567
 568         if (smb->pdata->soft_temp_limit_compensation !=
 569             SMB347_SOFT_TEMP_COMPENSATE_DEFAULT) {
 570                 val = smb->pdata->soft_temp_limit_compensation & 0x3;
 571
 572                 ret = regmap_update_bits(smb->regmap, CFG_THERM,
 573                                  CFG_THERM_SOFT_HOT_COMPENSATION_MASK,
 574                                  val << CFG_THERM_SOFT_HOT_COMPENSATION_SHIFT);
 575                 if (ret < 0)
 576                         return ret;
 577
 578                 ret = regmap_update_bits(smb->regmap, CFG_THERM,
 579                                  CFG_THERM_SOFT_COLD_COMPENSATION_MASK,
 580                                  val << CFG_THERM_SOFT_COLD_COMPENSATION_SHIFT);
 581                 if (ret < 0)
 582                         return ret;
 583         }
 584
 585         if (smb->pdata->charge_current_compensation) {
 586                 val = current_to_hw(ccc_tbl, ARRAY_SIZE(ccc_tbl),
 587                                     smb->pdata->charge_current_compensation);
 588                 if (val < 0)
 589                         return val;
 590
 591                 ret = regmap_update_bits(smb->regmap, CFG_OTG,
 592                                 CFG_OTG_CC_COMPENSATION_MASK,
 593                                 (val & 0x3) << CFG_OTG_CC_COMPENSATION_SHIFT);
 594                 if (ret < 0)
 595                         return ret;
 596         }
 597
 598         return ret;
 599 }
 600
 601 /*
 602  * smb347_set_writable - enables/disables writing to non-volatile registers
 603  * @smb: pointer to smb347 charger instance
 604  *
 605  * You can enable/disable writing to the non-volatile configuration
 606  * registers by calling this function.
 607  *
 608  * Returns %0 on success and negative errno in case of failure.
 609  */
 610 static int smb347_set_writable(struct smb347_charger *smb, bool writable)
 611 {
 612         return regmap_update_bits(smb->regmap, CMD_A, CMD_A_ALLOW_WRITE,
 613                                   writable ? CMD_A_ALLOW_WRITE : 0);
 614 }
 615
 616 static int smb347_hw_init(struct smb347_charger *smb)
 617 {
 618         unsigned int val;
 619         int ret;
 620
 621         ret = smb347_set_writable(smb, true);
 622         if (ret < 0)
 623                 return ret;
 624
 625         /*
 626          * Program the platform specific configuration values to the device
 627          * first.
 628          */
 629         ret = smb347_set_charge_current(smb);
 630         if (ret < 0)
 631                 goto fail;
 632
 633         ret = smb347_set_current_limits(smb);
 634         if (ret < 0)
 635                 goto fail;
 636
 637         ret = smb347_set_voltage_limits(smb);
 638         if (ret < 0)
 639                 goto fail;
 640
 641         ret = smb347_set_temp_limits(smb);
 642         if (ret < 0)
 643                 goto fail;
 644
 645         /* If USB charging is disabled we put the USB in suspend mode */
 646         if (!smb->pdata->use_usb) {
 647                 ret = regmap_update_bits(smb->regmap, CMD_A,
 648                                          CMD_A_SUSPEND_ENABLED,
 649                                          CMD_A_SUSPEND_ENABLED);
 650                 if (ret < 0)
 651                         goto fail;
 652         }
 653
 654         /*
 655          * If configured by platform data, we enable hardware Auto-OTG
 656          * support for driving VBUS. Otherwise we disable it.
 657          */
 658         ret = regmap_update_bits(smb->regmap, CFG_OTHER, CFG_OTHER_RID_MASK,
 659                 smb->pdata->use_usb_otg ? CFG_OTHER_RID_ENABLED_AUTO_OTG : 0);
 660         if (ret < 0)
 661                 goto fail;
 662
 663         /*
 664          * Make the charging functionality controllable by a write to the
 665          * command register unless pin control is specified in the platform
 666          * data.
 667          */
 668         switch (smb->pdata->enable_control) {
 669         case SMB347_CHG_ENABLE_PIN_ACTIVE_LOW:
 670                 val = CFG_PIN_EN_CTRL_ACTIVE_LOW;
 671                 break;
 672         case SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH:
 673                 val = CFG_PIN_EN_CTRL_ACTIVE_HIGH;
 674                 break;
 675         default:
 676                 val = 0;
 677                 break;
 678         }
 679
 680         ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CTRL_MASK,
 681                                  val);
 682         if (ret < 0)
 683                 goto fail;
 684
 685         /* Disable Automatic Power Source Detection (APSD) interrupt. */
 686         ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_APSD_IRQ, 0);
 687         if (ret < 0)
 688                 goto fail;
 689
 690         ret = smb347_update_ps_status(smb);
 691         if (ret < 0)
 692                 goto fail;
 693
 694         ret = smb347_start_stop_charging(smb);
 695
 696 fail:
 697         smb347_set_writable(smb, false);
 698         return ret;
 699 }
 700
 701 static irqreturn_t smb347_interrupt(int irq, void *data)
 702 {
 703         struct smb347_charger *smb = data;
 704         unsigned int stat_c, irqstat_e, irqstat_c;
 705         bool handled = false;
 706         int ret;
 707
 708         ret = regmap_read(smb->regmap, STAT_C, &stat_c);
 709         if (ret < 0) {
 710                 dev_warn(smb->dev, "reading STAT_C failed\n");
 711                 return IRQ_NONE;
 712         }
 713
 714         ret = regmap_read(smb->regmap, IRQSTAT_C, &irqstat_c);
 715         if (ret < 0) {
 716                 dev_warn(smb->dev, "reading IRQSTAT_C failed\n");
 717                 return IRQ_NONE;
 718         }
 719
 720         ret = regmap_read(smb->regmap, IRQSTAT_E, &irqstat_e);
 721         if (ret < 0) {
 722                 dev_warn(smb->dev, "reading IRQSTAT_E failed\n");
 723                 return IRQ_NONE;
 724         }
 725
 726         /*
 727          * If we get charger error we report the error back to user and
 728          * disable charging.
 729          */
 730         if (stat_c & STAT_C_CHARGER_ERROR) {
 731                 dev_err(smb->dev, "error in charger, disabling charging\n");
 732
 733                 smb347_charging_disable(smb);
 734                 power_supply_changed(&smb->battery);
 735                 handled = true;
 736         }
 737
 738         /*
 739          * If we reached the termination current the battery is charged and
 740          * we can update the status now. Charging is automatically
 741          * disabled by the hardware.
 742          */
 743         if (irqstat_c & (IRQSTAT_C_TERMINATION_IRQ | IRQSTAT_C_TAPER_IRQ)) {
 744                 if (irqstat_c & IRQSTAT_C_TERMINATION_STAT)
 745                         power_supply_changed(&smb->battery);
 746                 handled = true;
 747         }
 748
 749         /*
 750          * If we got an under voltage interrupt it means that AC/USB input
 751          * was connected or disconnected.
 752          */
 753         if (irqstat_e & (IRQSTAT_E_USBIN_UV_IRQ | IRQSTAT_E_DCIN_UV_IRQ)) {
 754                 if (smb347_update_ps_status(smb) > 0) {
 755                         smb347_start_stop_charging(smb);
 756                         if (smb->pdata->use_mains)
 757                                 power_supply_changed(&smb->mains);
 758                         if (smb->pdata->use_usb)
 759                                 power_supply_changed(&smb->usb);
 760                 }
 761                 handled = true;
 762         }
 763
 764         return handled ? IRQ_HANDLED : IRQ_NONE;
 765 }
 766
 767 static int smb347_irq_set(struct smb347_charger *smb, bool enable)
 768 {
 769         int ret;
 770
 771         ret = smb347_set_writable(smb, true);
 772         if (ret < 0)
 773                 return ret;
 774
 775         /*
 776          * Enable/disable interrupts for:
 777          *      - under voltage
 778          *      - termination current reached
 779          *      - charger error
 780          */
 781         ret = regmap_update_bits(smb->regmap, CFG_FAULT_IRQ, 0xff,
 782                                  enable ? CFG_FAULT_IRQ_DCIN_UV : 0);
 783         if (ret < 0)
 784                 goto fail;
 785
 786         ret = regmap_update_bits(smb->regmap, CFG_STATUS_IRQ, 0xff,
 787                         enable ? CFG_STATUS_IRQ_TERMINATION_OR_TAPER : 0);
 788         if (ret < 0)
 789                 goto fail;
 790
 791         ret = regmap_update_bits(smb->regmap, CFG_PIN, CFG_PIN_EN_CHARGER_ERROR,
 792                                  enable ? CFG_PIN_EN_CHARGER_ERROR : 0);
 793 fail:
 794         smb347_set_writable(smb, false);
 795         return ret;
 796 }
 797
 798 static inline int smb347_irq_enable(struct smb347_charger *smb)
 799 {
 800         return smb347_irq_set(smb, true);
 801 }
 802
 803 static inline int smb347_irq_disable(struct smb347_charger *smb)
 804 {
 805         return smb347_irq_set(smb, false);
 806 }
 807
 808 static int smb347_irq_init(struct smb347_charger *smb,
 809                            struct i2c_client *client)
 810 {
 811         const struct smb347_charger_platform_data *pdata = smb->pdata;
 812         int ret, irq = gpio_to_irq(pdata->irq_gpio);
 813
 814         ret = gpio_request_one(pdata->irq_gpio, GPIOF_IN, client->name);
 815         if (ret < 0)
 816                 goto fail;
 817
 818         ret = request_threaded_irq(irq, NULL, smb347_interrupt,
 819                                    IRQF_TRIGGER_FALLING, client->name, smb);
 820         if (ret < 0)
 821                 goto fail_gpio;
 822
 823         ret = smb347_set_writable(smb, true);
 824         if (ret < 0)
 825                 goto fail_irq;
 826
 827         /*
 828          * Configure the STAT output to be suitable for interrupts: disable
 829          * all other output (except interrupts) and make it active low.
 830          */
 831         ret = regmap_update_bits(smb->regmap, CFG_STAT,
 832                                  CFG_STAT_ACTIVE_HIGH | CFG_STAT_DISABLED,
 833                                  CFG_STAT_DISABLED);
 834         if (ret < 0)
 835                 goto fail_readonly;
 836
 837         smb347_set_writable(smb, false);
 838         client->irq = irq;
 839         return 0;
 840
 841 fail_readonly:
 842         smb347_set_writable(smb, false);
 843 fail_irq:
 844         free_irq(irq, smb);
 845 fail_gpio:
 846         gpio_free(pdata->irq_gpio);
 847 fail:
 848         client->irq = 0;
 849         return ret;
 850 }
 851
 852 /*
 853  * Returns the constant charge current programmed
 854  * into the charger in uA.
 855  */
 856 static int get_const_charge_current(struct smb347_charger *smb)
 857 {
 858         int ret, intval;
 859         unsigned int v;
 860
 861         if (!smb347_is_ps_online(smb))
 862                 return -ENODATA;
 863
 864         ret = regmap_read(smb->regmap, STAT_B, &v);
 865         if (ret < 0)
 866                 return ret;
 867
 868         /*
 869          * The current value is composition of FCC and PCC values
 870          * and we can detect which table to use from bit 5.
 871          */
 872         if (v & 0x20) {
 873                 intval = hw_to_current(fcc_tbl, ARRAY_SIZE(fcc_tbl), v & 7);
 874         } else {
 875                 v >>= 3;
 876                 intval = hw_to_current(pcc_tbl, ARRAY_SIZE(pcc_tbl), v & 7);
 877         }
 878
 879         return intval;
 880 }
 881
 882 /*
 883  * Returns the constant charge voltage programmed
 884  * into the charger in uV.
 885  */
 886 static int get_const_charge_voltage(struct smb347_charger *smb)
 887 {
 888         int ret, intval;
 889         unsigned int v;
 890
 891         if (!smb347_is_ps_online(smb))
 892                 return -ENODATA;
 893
 894         ret = regmap_read(smb->regmap, STAT_A, &v);
 895         if (ret < 0)
 896                 return ret;
 897
 898         v &= STAT_A_FLOAT_VOLTAGE_MASK;
 899         if (v > 0x3d)
 900                 v = 0x3d;
 901
 902         intval = 3500000 + v * 20000;
 903
 904         return intval;
 905 }
 906
 907 static int smb347_mains_get_property(struct power_supply *psy,
 908                                      enum power_supply_property prop,
 909                                      union power_supply_propval *val)
 910 {
 911         struct smb347_charger *smb =
 912                 container_of(psy, struct smb347_charger, mains);
 913         int ret;
 914
 915         switch (prop) {
 916         case POWER_SUPPLY_PROP_ONLINE:
 917                 val->intval = smb->mains_online;
 918                 break;
 919
 920         case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
 921                 ret = get_const_charge_voltage(smb);
 922                 if (ret < 0)
 923                         return ret;
 924                 else
 925                         val->intval = ret;
 926                 break;
 927
 928         case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
 929                 ret = get_const_charge_current(smb);
 930                 if (ret < 0)
 931                         return ret;
 932                 else
 933                         val->intval = ret;
 934                 break;
 935
 936         default:
 937                 return -EINVAL;
 938         }
 939
 940         return 0;
 941 }
 942
 943 static enum power_supply_property smb347_mains_properties[] = {
 944         POWER_SUPPLY_PROP_ONLINE,
 945         POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
 946         POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
 947 };
 948
 949 static int smb347_usb_get_property(struct power_supply *psy,
 950                                    enum power_supply_property prop,
 951                                    union power_supply_propval *val)
 952 {
 953         struct smb347_charger *smb =
 954                 container_of(psy, struct smb347_charger, usb);
 955         int ret;
 956
 957         switch (prop) {
 958         case POWER_SUPPLY_PROP_ONLINE:
 959                 val->intval = smb->usb_online;
 960                 break;
 961
 962         case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
 963                 ret = get_const_charge_voltage(smb);
 964                 if (ret < 0)
 965                         return ret;
 966                 else
 967                         val->intval = ret;
 968                 break;
 969
 970         case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
 971                 ret = get_const_charge_current(smb);
 972                 if (ret < 0)
 973                         return ret;
 974                 else
 975                         val->intval = ret;
 976                 break;
 977
 978         default:
 979                 return -EINVAL;
 980         }
 981
 982         return 0;
 983 }
 984
 985 static enum power_supply_property smb347_usb_properties[] = {
 986         POWER_SUPPLY_PROP_ONLINE,
 987         POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
 988         POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
 989 };
 990
 991 static int smb347_battery_get_property(struct power_supply *psy,
 992                                        enum power_supply_property prop,
 993                                        union power_supply_propval *val)
 994 {
 995         struct smb347_charger *smb =
 996                         container_of(psy, struct smb347_charger, battery);
 997         const struct smb347_charger_platform_data *pdata = smb->pdata;
 998         int ret;
 999
1000         ret = smb347_update_ps_status(smb);
1001         if (ret < 0)
1002                 return ret;
1003
1004         switch (prop) {
1005         case POWER_SUPPLY_PROP_STATUS:
1006                 if (!smb347_is_ps_online(smb)) {
1007                         val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
1008                         break;
1009                 }
1010                 if (smb347_charging_status(smb))
1011                         val->intval = POWER_SUPPLY_STATUS_CHARGING;
1012                 else
1013                         val->intval = POWER_SUPPLY_STATUS_FULL;
1014                 break;
1015
1016         case POWER_SUPPLY_PROP_CHARGE_TYPE:
1017                 if (!smb347_is_ps_online(smb))
1018                         return -ENODATA;
1019
1020                 /*
1021                  * We handle trickle and pre-charging the same, and taper
1022                  * and none the same.
1023                  */
1024                 switch (smb347_charging_status(smb)) {
1025                 case 1:
1026                         val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
1027                         break;
1028                 case 2:
1029                         val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST;
1030                         break;
1031                 default:
1032                         val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE;
1033                         break;
1034                 }
1035                 break;
1036
1037         case POWER_SUPPLY_PROP_TECHNOLOGY:
1038                 val->intval = pdata->battery_info.technology;
1039                 break;
1040
1041         case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
1042                 val->intval = pdata->battery_info.voltage_min_design;
1043                 break;
1044
1045         case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN:
1046                 val->intval = pdata->battery_info.voltage_max_design;
1047                 break;
1048
1049         case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
1050                 val->intval = pdata->battery_info.charge_full_design;
1051                 break;
1052
1053         case POWER_SUPPLY_PROP_MODEL_NAME:
1054                 val->strval = pdata->battery_info.name;
1055                 break;
1056
1057         default:
1058                 return -EINVAL;
1059         }
1060
1061         return 0;
1062 }
1063
1064 static enum power_supply_property smb347_battery_properties[] = {
1065         POWER_SUPPLY_PROP_STATUS,
1066         POWER_SUPPLY_PROP_CHARGE_TYPE,
1067         POWER_SUPPLY_PROP_TECHNOLOGY,
1068         POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN,
1069         POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN,
1070         POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
1071         POWER_SUPPLY_PROP_MODEL_NAME,
1072 };
1073
1074 static bool smb347_volatile_reg(struct device *dev, unsigned int reg)
1075 {
1076         switch (reg) {
1077         case IRQSTAT_A:
1078         case IRQSTAT_C:
1079         case IRQSTAT_E:
1080         case IRQSTAT_F:
1081         case STAT_A:
1082         case STAT_B:
1083         case STAT_C:
1084         case STAT_E:
1085                 return true;
1086         }
1087
1088         return false;
1089 }
1090
1091 static bool smb347_readable_reg(struct device *dev, unsigned int reg)
1092 {
1093         switch (reg) {
1094         case CFG_CHARGE_CURRENT:
1095         case CFG_CURRENT_LIMIT:
1096         case CFG_FLOAT_VOLTAGE:
1097         case CFG_STAT:
1098         case CFG_PIN:
1099         case CFG_THERM:
1100         case CFG_SYSOK:
1101         case CFG_OTHER:
1102         case CFG_OTG:
1103         case CFG_TEMP_LIMIT:
1104         case CFG_FAULT_IRQ:
1105         case CFG_STATUS_IRQ:
1106         case CFG_ADDRESS:
1107         case CMD_A:
1108         case CMD_B:
1109         case CMD_C:
1110                 return true;
1111         }
1112
1113         return smb347_volatile_reg(dev, reg);
1114 }
1115
1116 static const struct regmap_config smb347_regmap = {
1117         .reg_bits       = 8,
1118         .val_bits       = 8,
1119         .max_register   = SMB347_MAX_REGISTER,
1120         .volatile_reg   = smb347_volatile_reg,
1121         .readable_reg   = smb347_readable_reg,
1122 };
1123
1124 static int smb347_probe(struct i2c_client *client,
1125                         const struct i2c_device_id *id)
1126 {
1127         static char *battery[] = { "smb347-battery" };
1128         const struct smb347_charger_platform_data *pdata;
1129         struct device *dev = &client->dev;
1130         struct smb347_charger *smb;
1131         int ret;
1132
1133         pdata = dev->platform_data;
1134         if (!pdata)
1135                 return -EINVAL;
1136
1137         if (!pdata->use_mains && !pdata->use_usb)
1138                 return -EINVAL;
1139
1140         smb = devm_kzalloc(dev, sizeof(*smb), GFP_KERNEL);
1141         if (!smb)
1142                 return -ENOMEM;
1143
1144         i2c_set_clientdata(client, smb);
1145
1146         mutex_init(&smb->lock);
1147         smb->dev = &client->dev;
1148         smb->pdata = pdata;
1149
1150         smb->regmap = devm_regmap_init_i2c(client, &smb347_regmap);
1151         if (IS_ERR(smb->regmap))
1152                 return PTR_ERR(smb->regmap);
1153
1154         ret = smb347_hw_init(smb);
1155         if (ret < 0)
1156                 return ret;
1157
1158         if (smb->pdata->use_mains) {
1159                 smb->mains.name = "smb347-mains";
1160                 smb->mains.type = POWER_SUPPLY_TYPE_MAINS;
1161                 smb->mains.get_property = smb347_mains_get_property;
1162                 smb->mains.properties = smb347_mains_properties;
1163                 smb->mains.num_properties = ARRAY_SIZE(smb347_mains_properties);
1164                 smb->mains.supplied_to = battery;
1165                 smb->mains.num_supplicants = ARRAY_SIZE(battery);
1166                 ret = power_supply_register(dev, &smb->mains);
1167                 if (ret < 0)
1168                         return ret;
1169         }
1170
1171         if (smb->pdata->use_usb) {
1172                 smb->usb.name = "smb347-usb";
1173                 smb->usb.type = POWER_SUPPLY_TYPE_USB;
1174                 smb->usb.get_property = smb347_usb_get_property;
1175                 smb->usb.properties = smb347_usb_properties;
1176                 smb->usb.num_properties = ARRAY_SIZE(smb347_usb_properties);
1177                 smb->usb.supplied_to = battery;
1178                 smb->usb.num_supplicants = ARRAY_SIZE(battery);
1179                 ret = power_supply_register(dev, &smb->usb);
1180                 if (ret < 0) {
1181                         if (smb->pdata->use_mains)
1182                                 power_supply_unregister(&smb->mains);
1183                         return ret;
1184                 }
1185         }
1186
1187         smb->battery.name = "smb347-battery";
1188         smb->battery.type = POWER_SUPPLY_TYPE_BATTERY;
1189         smb->battery.get_property = smb347_battery_get_property;
1190         smb->battery.properties = smb347_battery_properties;
1191         smb->battery.num_properties = ARRAY_SIZE(smb347_battery_properties);
1192
1193
1194         ret = power_supply_register(dev, &smb->battery);
1195         if (ret < 0) {
1196                 if (smb->pdata->use_usb)
1197                         power_supply_unregister(&smb->usb);
1198                 if (smb->pdata->use_mains)
1199                         power_supply_unregister(&smb->mains);
1200                 return ret;
1201         }
1202
1203         /*
1204          * Interrupt pin is optional. If it is connected, we setup the
1205          * interrupt support here.
1206          */
1207         if (pdata->irq_gpio >= 0) {
1208                 ret = smb347_irq_init(smb, client);
1209                 if (ret < 0) {
1210                         dev_warn(dev, "failed to initialize IRQ: %d\n", ret);
1211                         dev_warn(dev, "disabling IRQ support\n");
1212                 } else {
1213                         smb347_irq_enable(smb);
1214                 }
1215         }
1216
1217         return 0;
1218 }
1219
1220 static int smb347_remove(struct i2c_client *client)
1221 {
1222         struct smb347_charger *smb = i2c_get_clientdata(client);
1223
1224         if (client->irq) {
1225                 smb347_irq_disable(smb);
1226                 free_irq(client->irq, smb);
1227                 gpio_free(smb->pdata->irq_gpio);
1228         }
1229
1230         power_supply_unregister(&smb->battery);
1231         if (smb->pdata->use_usb)
1232                 power_supply_unregister(&smb->usb);
1233         if (smb->pdata->use_mains)
1234                 power_supply_unregister(&smb->mains);
1235         return 0;
1236 }
1237
1238 static const struct i2c_device_id smb347_id[] = {
1239         { "smb347", 0 },
1240         { }
1241 };
1242 MODULE_DEVICE_TABLE(i2c, smb347_id);
1243
1244 static struct i2c_driver smb347_driver = {
1245         .driver = {
1246                 .name = "smb347",
1247         },
1248         .probe        = smb347_probe,
1249         .remove       = __devexit_p(smb347_remove),
1250         .id_table     = smb347_id,
1251 };
1252
1253 module_i2c_driver(smb347_driver);
1254
1255 MODULE_AUTHOR("Bruce E. Robertson <bruce.e.robertson@intel.com>");
1256 MODULE_AUTHOR("Mika Westerberg <mika.westerberg@linux.intel.com>");
1257 MODULE_DESCRIPTION("SMB347 battery charger driver");
1258 MODULE_LICENSE("GPL");
1259 MODULE_ALIAS("i2c:smb347");