drivers/net/sungem_phy.c

   1 /*
   2  * PHY drivers for the sungem ethernet driver.
   3  *
   4  * This file could be shared with other drivers.
   5  *
   6  * (c) 2002, Benjamin Herrenscmidt (benh@kernel.crashing.org)
   7  *
   8  * TODO:
   9  *  - Implement WOL
  10  *  - Add support for PHYs that provide an IRQ line
  11  *  - Eventually moved the entire polling state machine in
  12  *    there (out of the eth driver), so that it can easily be
  13  *    skipped on PHYs that implement it in hardware.
  14  *  - On LXT971 & BCM5201, Apple uses some chip specific regs
  15  *    to read the link status. Figure out why and if it makes
  16  *    sense to do the same (magic aneg ?)
  17  *  - Apple has some additional power management code for some
  18  *    Broadcom PHYs that they "hide" from the OpenSource version
  19  *    of darwin, still need to reverse engineer that
  20  */
  21
  22 #include <linux/config.h>
  23
  24 #include <linux/module.h>
  25
  26 #include <linux/kernel.h>
  27 #include <linux/sched.h>
  28 #include <linux/types.h>
  29 #include <linux/netdevice.h>
  30 #include <linux/etherdevice.h>
  31 #include <linux/mii.h>
  32 #include <linux/ethtool.h>
  33 #include <linux/delay.h>
  34
  35 #ifdef CONFIG_PPC_PMAC
  36 #include <asm/prom.h>
  37 #endif
  38
  39 #include "sungem_phy.h"
  40
  41 /* Link modes of the BCM5400 PHY */
  42 static const int phy_BCM5400_link_table[8][3] = {
  43         { 0, 0, 0 },    /* No link */
  44         { 0, 0, 0 },    /* 10BT Half Duplex */
  45         { 1, 0, 0 },    /* 10BT Full Duplex */
  46         { 0, 1, 0 },    /* 100BT Half Duplex */
  47         { 0, 1, 0 },    /* 100BT Half Duplex */
  48         { 1, 1, 0 },    /* 100BT Full Duplex*/
  49         { 1, 0, 1 },    /* 1000BT */
  50         { 1, 0, 1 },    /* 1000BT */
  51 };
  52
  53 static inline int __phy_read(struct mii_phy* phy, int id, int reg)
  54 {
  55         return phy->mdio_read(phy->dev, id, reg);
  56 }
  57
  58 static inline void __phy_write(struct mii_phy* phy, int id, int reg, int val)
  59 {
  60         phy->mdio_write(phy->dev, id, reg, val);
  61 }
  62
  63 static inline int phy_read(struct mii_phy* phy, int reg)
  64 {
  65         return phy->mdio_read(phy->dev, phy->mii_id, reg);
  66 }
  67
  68 static inline void phy_write(struct mii_phy* phy, int reg, int val)
  69 {
  70         phy->mdio_write(phy->dev, phy->mii_id, reg, val);
  71 }
  72
  73 static int reset_one_mii_phy(struct mii_phy* phy, int phy_id)
  74 {
  75         u16 val;
  76         int limit = 10000;
  77
  78         val = __phy_read(phy, phy_id, MII_BMCR);
  79         val &= ~(BMCR_ISOLATE | BMCR_PDOWN);
  80         val |= BMCR_RESET;
  81         __phy_write(phy, phy_id, MII_BMCR, val);
  82
  83         udelay(100);
  84
  85         while (limit--) {
  86                 val = __phy_read(phy, phy_id, MII_BMCR);
  87                 if ((val & BMCR_RESET) == 0)
  88                         break;
  89                 udelay(10);
  90         }
  91         if ((val & BMCR_ISOLATE) && limit > 0)
  92                 __phy_write(phy, phy_id, MII_BMCR, val & ~BMCR_ISOLATE);
  93
  94         return (limit <= 0);
  95 }
  96
  97 static int bcm5201_init(struct mii_phy* phy)
  98 {
  99         u16 data;
 100
 101         data = phy_read(phy, MII_BCM5201_MULTIPHY);
 102         data &= ~MII_BCM5201_MULTIPHY_SUPERISOLATE;
 103         phy_write(phy, MII_BCM5201_MULTIPHY, data);
 104
 105         phy_write(phy, MII_BCM5201_INTERRUPT, 0);
 106
 107         return 0;
 108 }
 109
 110 static int bcm5201_suspend(struct mii_phy* phy)
 111 {
 112         phy_write(phy, MII_BCM5201_INTERRUPT, 0);
 113         phy_write(phy, MII_BCM5201_MULTIPHY, MII_BCM5201_MULTIPHY_SUPERISOLATE);
 114
 115         return 0;
 116 }
 117
 118 static int bcm5221_init(struct mii_phy* phy)
 119 {
 120         u16 data;
 121
 122         data = phy_read(phy, MII_BCM5221_TEST);
 123         phy_write(phy, MII_BCM5221_TEST,
 124                 data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 125
 126         data = phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
 127         phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
 128                 data | MII_BCM5221_SHDOW_AUX_STAT2_APD);
 129
 130         data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
 131         phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 132                 data | MII_BCM5221_SHDOW_AUX_MODE4_CLKLOPWR);
 133
 134         data = phy_read(phy, MII_BCM5221_TEST);
 135         phy_write(phy, MII_BCM5221_TEST,
 136                 data & ~MII_BCM5221_TEST_ENABLE_SHADOWS);
 137
 138         return 0;
 139 }
 140
 141 static int bcm5221_suspend(struct mii_phy* phy)
 142 {
 143         u16 data;
 144
 145         data = phy_read(phy, MII_BCM5221_TEST);
 146         phy_write(phy, MII_BCM5221_TEST,
 147                 data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 148
 149         data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
 150         phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 151                   data | MII_BCM5221_SHDOW_AUX_MODE4_IDDQMODE);
 152
 153         return 0;
 154 }
 155
 156 static int bcm5400_init(struct mii_phy* phy)
 157 {
 158         u16 data;
 159
 160         /* Configure for gigabit full duplex */
 161         data = phy_read(phy, MII_BCM5400_AUXCONTROL);
 162         data |= MII_BCM5400_AUXCONTROL_PWR10BASET;
 163         phy_write(phy, MII_BCM5400_AUXCONTROL, data);
 164
 165         data = phy_read(phy, MII_BCM5400_GB_CONTROL);
 166         data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
 167         phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 168
 169         udelay(100);
 170
 171         /* Reset and configure cascaded 10/100 PHY */
 172         (void)reset_one_mii_phy(phy, 0x1f);
 173
 174         data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
 175         data |= MII_BCM5201_MULTIPHY_SERIALMODE;
 176         __phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
 177
 178         data = phy_read(phy, MII_BCM5400_AUXCONTROL);
 179         data &= ~MII_BCM5400_AUXCONTROL_PWR10BASET;
 180         phy_write(phy, MII_BCM5400_AUXCONTROL, data);
 181
 182         return 0;
 183 }
 184
 185 static int bcm5400_suspend(struct mii_phy* phy)
 186 {
 187 #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
 188         phy_write(phy, MII_BMCR, BMCR_PDOWN);
 189 #endif
 190         return 0;
 191 }
 192
 193 static int bcm5401_init(struct mii_phy* phy)
 194 {
 195         u16 data;
 196         int rev;
 197
 198         rev = phy_read(phy, MII_PHYSID2) & 0x000f;
 199         if (rev == 0 || rev == 3) {
 200                 /* Some revisions of 5401 appear to need this
 201                  * initialisation sequence to disable, according
 202                  * to OF, "tap power management"
 203                  *
 204                  * WARNING ! OF and Darwin don't agree on the
 205                  * register addresses. OF seem to interpret the
 206                  * register numbers below as decimal
 207                  *
 208                  * Note: This should (and does) match tg3_init_5401phy_dsp
 209                  *       in the tg3.c driver. -DaveM
 210                  */
 211                 phy_write(phy, 0x18, 0x0c20);
 212                 phy_write(phy, 0x17, 0x0012);
 213                 phy_write(phy, 0x15, 0x1804);
 214                 phy_write(phy, 0x17, 0x0013);
 215                 phy_write(phy, 0x15, 0x1204);
 216                 phy_write(phy, 0x17, 0x8006);
 217                 phy_write(phy, 0x15, 0x0132);
 218                 phy_write(phy, 0x17, 0x8006);
 219                 phy_write(phy, 0x15, 0x0232);
 220                 phy_write(phy, 0x17, 0x201f);
 221                 phy_write(phy, 0x15, 0x0a20);
 222         }
 223
 224         /* Configure for gigabit full duplex */
 225         data = phy_read(phy, MII_BCM5400_GB_CONTROL);
 226         data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
 227         phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 228
 229         udelay(10);
 230
 231         /* Reset and configure cascaded 10/100 PHY */
 232         (void)reset_one_mii_phy(phy, 0x1f);
 233
 234         data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
 235         data |= MII_BCM5201_MULTIPHY_SERIALMODE;
 236         __phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
 237
 238         return 0;
 239 }
 240
 241 static int bcm5401_suspend(struct mii_phy* phy)
 242 {
 243 #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
 244         phy_write(phy, MII_BMCR, BMCR_PDOWN);
 245 #endif
 246         return 0;
 247 }
 248
 249 static int bcm5411_init(struct mii_phy* phy)
 250 {
 251         u16 data;
 252
 253         /* Here's some more Apple black magic to setup
 254          * some voltage stuffs.
 255          */
 256         phy_write(phy, 0x1c, 0x8c23);
 257         phy_write(phy, 0x1c, 0x8ca3);
 258         phy_write(phy, 0x1c, 0x8c23);
 259
 260         /* Here, Apple seems to want to reset it, do
 261          * it as well
 262          */
 263         phy_write(phy, MII_BMCR, BMCR_RESET);
 264         phy_write(phy, MII_BMCR, 0x1340);
 265
 266         data = phy_read(phy, MII_BCM5400_GB_CONTROL);
 267         data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
 268         phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 269
 270         udelay(10);
 271
 272         /* Reset and configure cascaded 10/100 PHY */
 273         (void)reset_one_mii_phy(phy, 0x1f);
 274
 275         return 0;
 276 }
 277
 278 static int generic_suspend(struct mii_phy* phy)
 279 {
 280         phy_write(phy, MII_BMCR, BMCR_PDOWN);
 281
 282         return 0;
 283 }
 284
 285 static int bcm5421_init(struct mii_phy* phy)
 286 {
 287         u16 data;
 288         unsigned int id;
 289
 290         id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
 291
 292         /* Revision 0 of 5421 needs some fixups */
 293         if (id == 0x002060e0) {
 294                 /* This is borrowed from MacOS
 295                  */
 296                 phy_write(phy, 0x18, 0x1007);
 297                 data = phy_read(phy, 0x18);
 298                 phy_write(phy, 0x18, data | 0x0400);
 299                 phy_write(phy, 0x18, 0x0007);
 300                 data = phy_read(phy, 0x18);
 301                 phy_write(phy, 0x18, data | 0x0800);
 302                 phy_write(phy, 0x17, 0x000a);
 303                 data = phy_read(phy, 0x15);
 304                 phy_write(phy, 0x15, data | 0x0200);
 305         }
 306
 307         /* Pick up some init code from OF for K2 version */
 308         if ((id & 0xfffffff0) == 0x002062e0) {
 309                 phy_write(phy, 4, 0x01e1);
 310                 phy_write(phy, 9, 0x0300);
 311         }
 312
 313         /* Check if we can enable automatic low power */
 314 #ifdef CONFIG_PPC_PMAC
 315         if (phy->platform_data) {
 316                 struct device_node *np = of_get_parent(phy->platform_data);
 317                 int can_low_power = 1;
 318                 if (np == NULL || get_property(np, "no-autolowpower", NULL))
 319                         can_low_power = 0;
 320                 if (can_low_power) {
 321                         /* Enable automatic low-power */
 322                         phy_write(phy, 0x1c, 0x9002);
 323                         phy_write(phy, 0x1c, 0xa821);
 324                         phy_write(phy, 0x1c, 0x941d);
 325                 }
 326         }
 327 #endif /* CONFIG_PPC_PMAC */
 328
 329         return 0;
 330 }
 331
 332 static int bcm5421_enable_fiber(struct mii_phy* phy)
 333 {
 334         /* enable fiber mode */
 335         phy_write(phy, MII_NCONFIG, 0x9020);
 336         /* LEDs active in both modes, autosense prio = fiber */
 337         phy_write(phy, MII_NCONFIG, 0x945f);
 338
 339         /* switch off fibre autoneg */
 340         phy_write(phy, MII_NCONFIG, 0xfc01);
 341         phy_write(phy, 0x0b, 0x0004);
 342
 343         return 0;
 344 }
 345
 346 static int bcm5461_enable_fiber(struct mii_phy* phy)
 347 {
 348         phy_write(phy, MII_NCONFIG, 0xfc0c);
 349         phy_write(phy, MII_BMCR, 0x4140);
 350         phy_write(phy, MII_NCONFIG, 0xfc0b);
 351         phy_write(phy, MII_BMCR, 0x0140);
 352
 353         return 0;
 354 }
 355
 356 static int bcm54xx_setup_aneg(struct mii_phy *phy, u32 advertise)
 357 {
 358         u16 ctl, adv;
 359
 360         phy->autoneg = 1;
 361         phy->speed = SPEED_10;
 362         phy->duplex = DUPLEX_HALF;
 363         phy->pause = 0;
 364         phy->advertising = advertise;
 365
 366         /* Setup standard advertise */
 367         adv = phy_read(phy, MII_ADVERTISE);
 368         adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 369         if (advertise & ADVERTISED_10baseT_Half)
 370                 adv |= ADVERTISE_10HALF;
 371         if (advertise & ADVERTISED_10baseT_Full)
 372                 adv |= ADVERTISE_10FULL;
 373         if (advertise & ADVERTISED_100baseT_Half)
 374                 adv |= ADVERTISE_100HALF;
 375         if (advertise & ADVERTISED_100baseT_Full)
 376                 adv |= ADVERTISE_100FULL;
 377         phy_write(phy, MII_ADVERTISE, adv);
 378
 379         /* Setup 1000BT advertise */
 380         adv = phy_read(phy, MII_1000BASETCONTROL);
 381         adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP|MII_1000BASETCONTROL_HALFDUPLEXCAP);
 382         if (advertise & SUPPORTED_1000baseT_Half)
 383                 adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
 384         if (advertise & SUPPORTED_1000baseT_Full)
 385                 adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
 386         phy_write(phy, MII_1000BASETCONTROL, adv);
 387
 388         /* Start/Restart aneg */
 389         ctl = phy_read(phy, MII_BMCR);
 390         ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
 391         phy_write(phy, MII_BMCR, ctl);
 392
 393         return 0;
 394 }
 395
 396 static int bcm54xx_setup_forced(struct mii_phy *phy, int speed, int fd)
 397 {
 398         u16 ctl;
 399
 400         phy->autoneg = 0;
 401         phy->speed = speed;
 402         phy->duplex = fd;
 403         phy->pause = 0;
 404
 405         ctl = phy_read(phy, MII_BMCR);
 406         ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPD2|BMCR_ANENABLE);
 407
 408         /* First reset the PHY */
 409         phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
 410
 411         /* Select speed & duplex */
 412         switch(speed) {
 413         case SPEED_10:
 414                 break;
 415         case SPEED_100:
 416                 ctl |= BMCR_SPEED100;
 417                 break;
 418         case SPEED_1000:
 419                 ctl |= BMCR_SPD2;
 420         }
 421         if (fd == DUPLEX_FULL)
 422                 ctl |= BMCR_FULLDPLX;
 423
 424         // XXX Should we set the sungem to GII now on 1000BT ?
 425
 426         phy_write(phy, MII_BMCR, ctl);
 427
 428         return 0;
 429 }
 430
 431 static int bcm54xx_read_link(struct mii_phy *phy)
 432 {
 433         int link_mode;
 434         u16 val;
 435
 436         if (phy->autoneg) {
 437                 val = phy_read(phy, MII_BCM5400_AUXSTATUS);
 438                 link_mode = ((val & MII_BCM5400_AUXSTATUS_LINKMODE_MASK) >>
 439                              MII_BCM5400_AUXSTATUS_LINKMODE_SHIFT);
 440                 phy->duplex = phy_BCM5400_link_table[link_mode][0] ? DUPLEX_FULL : DUPLEX_HALF;
 441                 phy->speed = phy_BCM5400_link_table[link_mode][2] ?
 442                                 SPEED_1000 :
 443                                 (phy_BCM5400_link_table[link_mode][1] ? SPEED_100 : SPEED_10);
 444                 val = phy_read(phy, MII_LPA);
 445                 phy->pause = ((val & LPA_PAUSE) != 0);
 446         }
 447         /* On non-aneg, we assume what we put in BMCR is the speed,
 448          * though magic-aneg shouldn't prevent this case from occurring
 449          */
 450
 451         return 0;
 452 }
 453
 454 static int marvell_setup_aneg(struct mii_phy *phy, u32 advertise)
 455 {
 456         u16 ctl, adv;
 457
 458         phy->autoneg = 1;
 459         phy->speed = SPEED_10;
 460         phy->duplex = DUPLEX_HALF;
 461         phy->pause = 0;
 462         phy->advertising = advertise;
 463
 464         /* Setup standard advertise */
 465         adv = phy_read(phy, MII_ADVERTISE);
 466         adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 467         if (advertise & ADVERTISED_10baseT_Half)
 468                 adv |= ADVERTISE_10HALF;
 469         if (advertise & ADVERTISED_10baseT_Full)
 470                 adv |= ADVERTISE_10FULL;
 471         if (advertise & ADVERTISED_100baseT_Half)
 472                 adv |= ADVERTISE_100HALF;
 473         if (advertise & ADVERTISED_100baseT_Full)
 474                 adv |= ADVERTISE_100FULL;
 475         phy_write(phy, MII_ADVERTISE, adv);
 476
 477         /* Setup 1000BT advertise & enable crossover detect
 478          * XXX How do we advertise 1000BT ? Darwin source is
 479          * confusing here, they read from specific control and
 480          * write to control... Someone has specs for those
 481          * beasts ?
 482          */
 483         adv = phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
 484         adv |= MII_M1011_PHY_SPEC_CONTROL_AUTO_MDIX;
 485         adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP |
 486                         MII_1000BASETCONTROL_HALFDUPLEXCAP);
 487         if (advertise & SUPPORTED_1000baseT_Half)
 488                 adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
 489         if (advertise & SUPPORTED_1000baseT_Full)
 490                 adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
 491         phy_write(phy, MII_1000BASETCONTROL, adv);
 492
 493         /* Start/Restart aneg */
 494         ctl = phy_read(phy, MII_BMCR);
 495         ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
 496         phy_write(phy, MII_BMCR, ctl);
 497
 498         return 0;
 499 }
 500
 501 static int marvell_setup_forced(struct mii_phy *phy, int speed, int fd)
 502 {
 503         u16 ctl, ctl2;
 504
 505         phy->autoneg = 0;
 506         phy->speed = speed;
 507         phy->duplex = fd;
 508         phy->pause = 0;
 509
 510         ctl = phy_read(phy, MII_BMCR);
 511         ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPD2|BMCR_ANENABLE);
 512         ctl |= BMCR_RESET;
 513
 514         /* Select speed & duplex */
 515         switch(speed) {
 516         case SPEED_10:
 517                 break;
 518         case SPEED_100:
 519                 ctl |= BMCR_SPEED100;
 520                 break;
 521         /* I'm not sure about the one below, again, Darwin source is
 522          * quite confusing and I lack chip specs
 523          */
 524         case SPEED_1000:
 525                 ctl |= BMCR_SPD2;
 526         }
 527         if (fd == DUPLEX_FULL)
 528                 ctl |= BMCR_FULLDPLX;
 529
 530         /* Disable crossover. Again, the way Apple does it is strange,
 531          * though I don't assume they are wrong ;)
 532          */
 533         ctl2 = phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
 534         ctl2 &= ~(MII_M1011_PHY_SPEC_CONTROL_MANUAL_MDIX |
 535                 MII_M1011_PHY_SPEC_CONTROL_AUTO_MDIX |
 536                 MII_1000BASETCONTROL_FULLDUPLEXCAP |
 537                 MII_1000BASETCONTROL_HALFDUPLEXCAP);
 538         if (speed == SPEED_1000)
 539                 ctl2 |= (fd == DUPLEX_FULL) ?
 540                         MII_1000BASETCONTROL_FULLDUPLEXCAP :
 541                         MII_1000BASETCONTROL_HALFDUPLEXCAP;
 542         phy_write(phy, MII_1000BASETCONTROL, ctl2);
 543
 544         // XXX Should we set the sungem to GII now on 1000BT ?
 545
 546         phy_write(phy, MII_BMCR, ctl);
 547
 548         return 0;
 549 }
 550
 551 static int marvell_read_link(struct mii_phy *phy)
 552 {
 553         u16 status;
 554
 555         if (phy->autoneg) {
 556                 status = phy_read(phy, MII_M1011_PHY_SPEC_STATUS);
 557                 if ((status & MII_M1011_PHY_SPEC_STATUS_RESOLVED) == 0)
 558                         return -EAGAIN;
 559                 if (status & MII_M1011_PHY_SPEC_STATUS_1000)
 560                         phy->speed = SPEED_1000;
 561                 else if (status & MII_M1011_PHY_SPEC_STATUS_100)
 562                         phy->speed = SPEED_100;
 563                 else
 564                         phy->speed = SPEED_10;
 565                 if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX)
 566                         phy->duplex = DUPLEX_FULL;
 567                 else
 568                         phy->duplex = DUPLEX_HALF;
 569                 phy->pause = 0; /* XXX Check against spec ! */
 570         }
 571         /* On non-aneg, we assume what we put in BMCR is the speed,
 572          * though magic-aneg shouldn't prevent this case from occurring
 573          */
 574
 575         return 0;
 576 }
 577
 578 static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise)
 579 {
 580         u16 ctl, adv;
 581
 582         phy->autoneg = 1;
 583         phy->speed = SPEED_10;
 584         phy->duplex = DUPLEX_HALF;
 585         phy->pause = 0;
 586         phy->advertising = advertise;
 587
 588         /* Setup standard advertise */
 589         adv = phy_read(phy, MII_ADVERTISE);
 590         adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 591         if (advertise & ADVERTISED_10baseT_Half)
 592                 adv |= ADVERTISE_10HALF;
 593         if (advertise & ADVERTISED_10baseT_Full)
 594                 adv |= ADVERTISE_10FULL;
 595         if (advertise & ADVERTISED_100baseT_Half)
 596                 adv |= ADVERTISE_100HALF;
 597         if (advertise & ADVERTISED_100baseT_Full)
 598                 adv |= ADVERTISE_100FULL;
 599         phy_write(phy, MII_ADVERTISE, adv);
 600
 601         /* Start/Restart aneg */
 602         ctl = phy_read(phy, MII_BMCR);
 603         ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
 604         phy_write(phy, MII_BMCR, ctl);
 605
 606         return 0;
 607 }
 608
 609 static int genmii_setup_forced(struct mii_phy *phy, int speed, int fd)
 610 {
 611         u16 ctl;
 612
 613         phy->autoneg = 0;
 614         phy->speed = speed;
 615         phy->duplex = fd;
 616         phy->pause = 0;
 617
 618         ctl = phy_read(phy, MII_BMCR);
 619         ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_ANENABLE);
 620
 621         /* First reset the PHY */
 622         phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
 623
 624         /* Select speed & duplex */
 625         switch(speed) {
 626         case SPEED_10:
 627                 break;
 628         case SPEED_100:
 629                 ctl |= BMCR_SPEED100;
 630                 break;
 631         case SPEED_1000:
 632         default:
 633                 return -EINVAL;
 634         }
 635         if (fd == DUPLEX_FULL)
 636                 ctl |= BMCR_FULLDPLX;
 637         phy_write(phy, MII_BMCR, ctl);
 638
 639         return 0;
 640 }
 641
 642 static int genmii_poll_link(struct mii_phy *phy)
 643 {
 644         u16 status;
 645
 646         (void)phy_read(phy, MII_BMSR);
 647         status = phy_read(phy, MII_BMSR);
 648         if ((status & BMSR_LSTATUS) == 0)
 649                 return 0;
 650         if (phy->autoneg && !(status & BMSR_ANEGCOMPLETE))
 651                 return 0;
 652         return 1;
 653 }
 654
 655 static int genmii_read_link(struct mii_phy *phy)
 656 {
 657         u16 lpa;
 658
 659         if (phy->autoneg) {
 660                 lpa = phy_read(phy, MII_LPA);
 661
 662                 if (lpa & (LPA_10FULL | LPA_100FULL))
 663                         phy->duplex = DUPLEX_FULL;
 664                 else
 665                         phy->duplex = DUPLEX_HALF;
 666                 if (lpa & (LPA_100FULL | LPA_100HALF))
 667                         phy->speed = SPEED_100;
 668                 else
 669                         phy->speed = SPEED_10;
 670                 phy->pause = 0;
 671         }
 672         /* On non-aneg, we assume what we put in BMCR is the speed,
 673          * though magic-aneg shouldn't prevent this case from occurring
 674          */
 675
 676          return 0;
 677 }
 678
 679
 680 #define MII_BASIC_FEATURES      (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \
 681                                  SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \
 682                                  SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII)
 683 #define MII_GBIT_FEATURES       (MII_BASIC_FEATURES | \
 684                                  SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full)
 685
 686 /* Broadcom BCM 5201 */
 687 static struct mii_phy_ops bcm5201_phy_ops = {
 688         .init           = bcm5201_init,
 689         .suspend        = bcm5201_suspend,
 690         .setup_aneg     = genmii_setup_aneg,
 691         .setup_forced   = genmii_setup_forced,
 692         .poll_link      = genmii_poll_link,
 693         .read_link      = genmii_read_link,
 694 };
 695
 696 static struct mii_phy_def bcm5201_phy_def = {
 697         .phy_id         = 0x00406210,
 698         .phy_id_mask    = 0xfffffff0,
 699         .name           = "BCM5201",
 700         .features       = MII_BASIC_FEATURES,
 701         .magic_aneg     = 1,
 702         .ops            = &bcm5201_phy_ops
 703 };
 704
 705 /* Broadcom BCM 5221 */
 706 static struct mii_phy_ops bcm5221_phy_ops = {
 707         .suspend        = bcm5221_suspend,
 708         .init           = bcm5221_init,
 709         .setup_aneg     = genmii_setup_aneg,
 710         .setup_forced   = genmii_setup_forced,
 711         .poll_link      = genmii_poll_link,
 712         .read_link      = genmii_read_link,
 713 };
 714
 715 static struct mii_phy_def bcm5221_phy_def = {
 716         .phy_id         = 0x004061e0,
 717         .phy_id_mask    = 0xfffffff0,
 718         .name           = "BCM5221",
 719         .features       = MII_BASIC_FEATURES,
 720         .magic_aneg     = 1,
 721         .ops            = &bcm5221_phy_ops
 722 };
 723
 724 /* Broadcom BCM 5400 */
 725 static struct mii_phy_ops bcm5400_phy_ops = {
 726         .init           = bcm5400_init,
 727         .suspend        = bcm5400_suspend,
 728         .setup_aneg     = bcm54xx_setup_aneg,
 729         .setup_forced   = bcm54xx_setup_forced,
 730         .poll_link      = genmii_poll_link,
 731         .read_link      = bcm54xx_read_link,
 732 };
 733
 734 static struct mii_phy_def bcm5400_phy_def = {
 735         .phy_id         = 0x00206040,
 736         .phy_id_mask    = 0xfffffff0,
 737         .name           = "BCM5400",
 738         .features       = MII_GBIT_FEATURES,
 739         .magic_aneg     = 1,
 740         .ops            = &bcm5400_phy_ops
 741 };
 742
 743 /* Broadcom BCM 5401 */
 744 static struct mii_phy_ops bcm5401_phy_ops = {
 745         .init           = bcm5401_init,
 746         .suspend        = bcm5401_suspend,
 747         .setup_aneg     = bcm54xx_setup_aneg,
 748         .setup_forced   = bcm54xx_setup_forced,
 749         .poll_link      = genmii_poll_link,
 750         .read_link      = bcm54xx_read_link,
 751 };
 752
 753 static struct mii_phy_def bcm5401_phy_def = {
 754         .phy_id         = 0x00206050,
 755         .phy_id_mask    = 0xfffffff0,
 756         .name           = "BCM5401",
 757         .features       = MII_GBIT_FEATURES,
 758         .magic_aneg     = 1,
 759         .ops            = &bcm5401_phy_ops
 760 };
 761
 762 /* Broadcom BCM 5411 */
 763 static struct mii_phy_ops bcm5411_phy_ops = {
 764         .init           = bcm5411_init,
 765         .suspend        = generic_suspend,
 766         .setup_aneg     = bcm54xx_setup_aneg,
 767         .setup_forced   = bcm54xx_setup_forced,
 768         .poll_link      = genmii_poll_link,
 769         .read_link      = bcm54xx_read_link,
 770 };
 771
 772 static struct mii_phy_def bcm5411_phy_def = {
 773         .phy_id         = 0x00206070,
 774         .phy_id_mask    = 0xfffffff0,
 775         .name           = "BCM5411",
 776         .features       = MII_GBIT_FEATURES,
 777         .magic_aneg     = 1,
 778         .ops            = &bcm5411_phy_ops
 779 };
 780
 781 /* Broadcom BCM 5421 */
 782 static struct mii_phy_ops bcm5421_phy_ops = {
 783         .init           = bcm5421_init,
 784         .suspend        = generic_suspend,
 785         .setup_aneg     = bcm54xx_setup_aneg,
 786         .setup_forced   = bcm54xx_setup_forced,
 787         .poll_link      = genmii_poll_link,
 788         .read_link      = bcm54xx_read_link,
 789         .enable_fiber   = bcm5421_enable_fiber,
 790 };
 791
 792 static struct mii_phy_def bcm5421_phy_def = {
 793         .phy_id         = 0x002060e0,
 794         .phy_id_mask    = 0xfffffff0,
 795         .name           = "BCM5421",
 796         .features       = MII_GBIT_FEATURES,
 797         .magic_aneg     = 1,
 798         .ops            = &bcm5421_phy_ops
 799 };
 800
 801 /* Broadcom BCM 5421 built-in K2 */
 802 static struct mii_phy_ops bcm5421k2_phy_ops = {
 803         .init           = bcm5421_init,
 804         .suspend        = generic_suspend,
 805         .setup_aneg     = bcm54xx_setup_aneg,
 806         .setup_forced   = bcm54xx_setup_forced,
 807         .poll_link      = genmii_poll_link,
 808         .read_link      = bcm54xx_read_link,
 809 };
 810
 811 static struct mii_phy_def bcm5421k2_phy_def = {
 812         .phy_id         = 0x002062e0,
 813         .phy_id_mask    = 0xfffffff0,
 814         .name           = "BCM5421-K2",
 815         .features       = MII_GBIT_FEATURES,
 816         .magic_aneg     = 1,
 817         .ops            = &bcm5421k2_phy_ops
 818 };
 819
 820 static struct mii_phy_ops bcm5461_phy_ops = {
 821         .init           = bcm5421_init,
 822         .suspend        = generic_suspend,
 823         .setup_aneg     = bcm54xx_setup_aneg,
 824         .setup_forced   = bcm54xx_setup_forced,
 825         .poll_link      = genmii_poll_link,
 826         .read_link      = bcm54xx_read_link,
 827         .enable_fiber   = bcm5461_enable_fiber,
 828 };
 829
 830 static struct mii_phy_def bcm5461_phy_def = {
 831         .phy_id         = 0x002060c0,
 832         .phy_id_mask    = 0xfffffff0,
 833         .name           = "BCM5461",
 834         .features       = MII_GBIT_FEATURES,
 835         .magic_aneg     = 1,
 836         .ops            = &bcm5461_phy_ops
 837 };
 838
 839 /* Broadcom BCM 5462 built-in Vesta */
 840 static struct mii_phy_ops bcm5462V_phy_ops = {
 841         .init           = bcm5421_init,
 842         .suspend        = generic_suspend,
 843         .setup_aneg     = bcm54xx_setup_aneg,
 844         .setup_forced   = bcm54xx_setup_forced,
 845         .poll_link      = genmii_poll_link,
 846         .read_link      = bcm54xx_read_link,
 847 };
 848
 849 static struct mii_phy_def bcm5462V_phy_def = {
 850         .phy_id         = 0x002060d0,
 851         .phy_id_mask    = 0xfffffff0,
 852         .name           = "BCM5462-Vesta",
 853         .features       = MII_GBIT_FEATURES,
 854         .magic_aneg     = 1,
 855         .ops            = &bcm5462V_phy_ops
 856 };
 857
 858 /* Marvell 88E1101 (Apple seem to deal with 2 different revs,
 859  * I masked out the 8 last bits to get both, but some specs
 860  * would be useful here) --BenH.
 861  */
 862 static struct mii_phy_ops marvell_phy_ops = {
 863         .suspend        = generic_suspend,
 864         .setup_aneg     = marvell_setup_aneg,
 865         .setup_forced   = marvell_setup_forced,
 866         .poll_link      = genmii_poll_link,
 867         .read_link      = marvell_read_link
 868 };
 869
 870 static struct mii_phy_def marvell_phy_def = {
 871         .phy_id         = 0x01410c00,
 872         .phy_id_mask    = 0xffffff00,
 873         .name           = "Marvell 88E1101",
 874         .features       = MII_GBIT_FEATURES,
 875         .magic_aneg     = 1,
 876         .ops            = &marvell_phy_ops
 877 };
 878
 879 /* Generic implementation for most 10/100 PHYs */
 880 static struct mii_phy_ops generic_phy_ops = {
 881         .setup_aneg     = genmii_setup_aneg,
 882         .setup_forced   = genmii_setup_forced,
 883         .poll_link      = genmii_poll_link,
 884         .read_link      = genmii_read_link
 885 };
 886
 887 static struct mii_phy_def genmii_phy_def = {
 888         .phy_id         = 0x00000000,
 889         .phy_id_mask    = 0x00000000,
 890         .name           = "Generic MII",
 891         .features       = MII_BASIC_FEATURES,
 892         .magic_aneg     = 0,
 893         .ops            = &generic_phy_ops
 894 };
 895
 896 static struct mii_phy_def* mii_phy_table[] = {
 897         &bcm5201_phy_def,
 898         &bcm5221_phy_def,
 899         &bcm5400_phy_def,
 900         &bcm5401_phy_def,
 901         &bcm5411_phy_def,
 902         &bcm5421_phy_def,
 903         &bcm5421k2_phy_def,
 904         &bcm5461_phy_def,
 905         &bcm5462V_phy_def,
 906         &marvell_phy_def,
 907         &genmii_phy_def,
 908         NULL
 909 };
 910
 911 int mii_phy_probe(struct mii_phy *phy, int mii_id)
 912 {
 913         int rc;
 914         u32 id;
 915         struct mii_phy_def* def;
 916         int i;
 917
 918         /* We do not reset the mii_phy structure as the driver
 919          * may re-probe the PHY regulary
 920          */
 921         phy->mii_id = mii_id;
 922
 923         /* Take PHY out of isloate mode and reset it. */
 924         rc = reset_one_mii_phy(phy, mii_id);
 925         if (rc)
 926                 goto fail;
 927
 928         /* Read ID and find matching entry */
 929         id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
 930         printk(KERN_DEBUG "PHY ID: %x, addr: %x\n", id, mii_id);
 931         for (i=0; (def = mii_phy_table[i]) != NULL; i++)
 932                 if ((id & def->phy_id_mask) == def->phy_id)
 933                         break;
 934         /* Should never be NULL (we have a generic entry), but... */
 935         if (def == NULL)
 936                 goto fail;
 937
 938         phy->def = def;
 939
 940         return 0;
 941 fail:
 942         phy->speed = 0;
 943         phy->duplex = 0;
 944         phy->pause = 0;
 945         phy->advertising = 0;
 946         return -ENODEV;
 947 }
 948
 949 EXPORT_SYMBOL(mii_phy_probe);
 950 MODULE_LICENSE("GPL");
 951