1 /************************************************************************
2 * s2io.c: A Linux PCI-X Ethernet driver for Neterion 10GbE Server NIC
3 * Copyright(c) 2002-2007 Neterion Inc.
5 * This software may be used and distributed according to the terms of
6 * the GNU General Public License (GPL), incorporated herein by reference.
7 * Drivers based on or derived from this code fall under the GPL and must
8 * retain the authorship, copyright and license notice. This file is not
9 * a complete program and may only be used when the entire operating
10 * system is licensed under the GPL.
11 * See the file COPYING in this distribution for more information.
14 * Jeff Garzik : For pointing out the improper error condition
15 * check in the s2io_xmit routine and also some
16 * issues in the Tx watch dog function. Also for
17 * patiently answering all those innumerable
18 * questions regaring the 2.6 porting issues.
19 * Stephen Hemminger : Providing proper 2.6 porting mechanism for some
20 * macros available only in 2.6 Kernel.
21 * Francois Romieu : For pointing out all code part that were
22 * deprecated and also styling related comments.
23 * Grant Grundler : For helping me get rid of some Architecture
25 * Christopher Hellwig : Some more 2.6 specific issues in the driver.
27 * The module loadable parameters that are supported by the driver and a brief
28 * explaination of all the variables.
30 * rx_ring_num : This can be used to program the number of receive rings used
32 * rx_ring_sz: This defines the number of receive blocks each ring can have.
33 * This is also an array of size 8.
34 * rx_ring_mode: This defines the operation mode of all 8 rings. The valid
36 * tx_fifo_num: This defines the number of Tx FIFOs thats used int the driver.
37 * tx_fifo_len: This too is an array of 8. Each element defines the number of
38 * Tx descriptors that can be associated with each corresponding FIFO.
39 * intr_type: This defines the type of interrupt. The values can be 0(INTA),
40 * 2(MSI_X). Default value is '2(MSI_X)'
41 * lro_enable: Specifies whether to enable Large Receive Offload (LRO) or not.
42 * Possible values '1' for enable '0' for disable. Default is '0'
43 * lro_max_pkts: This parameter defines maximum number of packets can be
44 * aggregated as a single large packet
45 * napi: This parameter used to enable/disable NAPI (polling Rx)
46 * Possible values '1' for enable and '0' for disable. Default is '1'
47 * ufo: This parameter used to enable/disable UDP Fragmentation Offload(UFO)
48 * Possible values '1' for enable and '0' for disable. Default is '0'
49 * vlan_tag_strip: This can be used to enable or disable vlan stripping.
50 * Possible values '1' for enable , '0' for disable.
51 * Default is '2' - which means disable in promisc mode
52 * and enable in non-promiscuous mode.
53 ************************************************************************/
55 #include <linux/module.h>
56 #include <linux/types.h>
57 #include <linux/errno.h>
58 #include <linux/ioport.h>
59 #include <linux/pci.h>
60 #include <linux/dma-mapping.h>
61 #include <linux/kernel.h>
62 #include <linux/netdevice.h>
63 #include <linux/etherdevice.h>
64 #include <linux/skbuff.h>
65 #include <linux/init.h>
66 #include <linux/delay.h>
67 #include <linux/stddef.h>
68 #include <linux/ioctl.h>
69 #include <linux/timex.h>
70 #include <linux/ethtool.h>
71 #include <linux/workqueue.h>
72 #include <linux/if_vlan.h>
74 #include <linux/tcp.h>
77 #include <asm/system.h>
78 #include <asm/uaccess.h>
80 #include <asm/div64.h>
85 #include "s2io-regs.h"
87 #define DRV_VERSION "2.0.26.6"
89 /* S2io Driver name & version. */
90 static char s2io_driver_name[] = "Neterion";
91 static char s2io_driver_version[] = DRV_VERSION;
93 static int rxd_size[2] = {32,48};
94 static int rxd_count[2] = {127,85};
96 static inline int RXD_IS_UP2DT(struct RxD_t *rxdp)
100 ret = ((!(rxdp->Control_1 & RXD_OWN_XENA)) &&
101 (GET_RXD_MARKER(rxdp->Control_2) != THE_RXD_MARK));
107 * Cards with following subsystem_id have a link state indication
108 * problem, 600B, 600C, 600D, 640B, 640C and 640D.
109 * macro below identifies these cards given the subsystem_id.
111 #define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \
112 (dev_type == XFRAME_I_DEVICE) ? \
113 ((((subid >= 0x600B) && (subid <= 0x600D)) || \
114 ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0
116 #define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \
117 ADAPTER_STATUS_RMAC_LOCAL_FAULT)))
118 #define TASKLET_IN_USE test_and_set_bit(0, (&sp->tasklet_status))
121 static inline int rx_buffer_level(struct s2io_nic * sp, int rxb_size, int ring)
123 struct mac_info *mac_control;
125 mac_control = &sp->mac_control;
126 if (rxb_size <= rxd_count[sp->rxd_mode])
128 else if ((mac_control->rings[ring].pkt_cnt - rxb_size) > 16)
133 static inline int is_s2io_card_up(const struct s2io_nic * sp)
135 return test_bit(__S2IO_STATE_CARD_UP, &sp->state);
138 /* Ethtool related variables and Macros. */
139 static char s2io_gstrings[][ETH_GSTRING_LEN] = {
140 "Register test\t(offline)",
141 "Eeprom test\t(offline)",
142 "Link test\t(online)",
143 "RLDRAM test\t(offline)",
144 "BIST Test\t(offline)"
147 static char ethtool_xena_stats_keys[][ETH_GSTRING_LEN] = {
149 {"tmac_data_octets"},
153 {"tmac_pause_ctrl_frms"},
157 {"tmac_any_err_frms"},
158 {"tmac_ttl_less_fb_octets"},
159 {"tmac_vld_ip_octets"},
167 {"rmac_data_octets"},
168 {"rmac_fcs_err_frms"},
170 {"rmac_vld_mcst_frms"},
171 {"rmac_vld_bcst_frms"},
172 {"rmac_in_rng_len_err_frms"},
173 {"rmac_out_rng_len_err_frms"},
175 {"rmac_pause_ctrl_frms"},
176 {"rmac_unsup_ctrl_frms"},
178 {"rmac_accepted_ucst_frms"},
179 {"rmac_accepted_nucst_frms"},
180 {"rmac_discarded_frms"},
181 {"rmac_drop_events"},
182 {"rmac_ttl_less_fb_octets"},
184 {"rmac_usized_frms"},
185 {"rmac_osized_frms"},
187 {"rmac_jabber_frms"},
188 {"rmac_ttl_64_frms"},
189 {"rmac_ttl_65_127_frms"},
190 {"rmac_ttl_128_255_frms"},
191 {"rmac_ttl_256_511_frms"},
192 {"rmac_ttl_512_1023_frms"},
193 {"rmac_ttl_1024_1518_frms"},
201 {"rmac_err_drp_udp"},
202 {"rmac_xgmii_err_sym"},
220 {"rmac_xgmii_data_err_cnt"},
221 {"rmac_xgmii_ctrl_err_cnt"},
222 {"rmac_accepted_ip"},
226 {"new_rd_req_rtry_cnt"},
228 {"wr_rtry_rd_ack_cnt"},
231 {"new_wr_req_rtry_cnt"},
234 {"rd_rtry_wr_ack_cnt"},
244 static char ethtool_enhanced_stats_keys[][ETH_GSTRING_LEN] = {
245 {"rmac_ttl_1519_4095_frms"},
246 {"rmac_ttl_4096_8191_frms"},
247 {"rmac_ttl_8192_max_frms"},
248 {"rmac_ttl_gt_max_frms"},
249 {"rmac_osized_alt_frms"},
250 {"rmac_jabber_alt_frms"},
251 {"rmac_gt_max_alt_frms"},
253 {"rmac_len_discard"},
254 {"rmac_fcs_discard"},
257 {"rmac_red_discard"},
258 {"rmac_rts_discard"},
259 {"rmac_ingm_full_discard"},
263 static char ethtool_driver_stats_keys[][ETH_GSTRING_LEN] = {
264 {"\n DRIVER STATISTICS"},
265 {"single_bit_ecc_errs"},
266 {"double_bit_ecc_errs"},
279 {"alarm_transceiver_temp_high"},
280 {"alarm_transceiver_temp_low"},
281 {"alarm_laser_bias_current_high"},
282 {"alarm_laser_bias_current_low"},
283 {"alarm_laser_output_power_high"},
284 {"alarm_laser_output_power_low"},
285 {"warn_transceiver_temp_high"},
286 {"warn_transceiver_temp_low"},
287 {"warn_laser_bias_current_high"},
288 {"warn_laser_bias_current_low"},
289 {"warn_laser_output_power_high"},
290 {"warn_laser_output_power_low"},
291 {"lro_aggregated_pkts"},
292 {"lro_flush_both_count"},
293 {"lro_out_of_sequence_pkts"},
294 {"lro_flush_due_to_max_pkts"},
295 {"lro_avg_aggr_pkts"},
296 {"mem_alloc_fail_cnt"},
297 {"pci_map_fail_cnt"},
298 {"watchdog_timer_cnt"},
305 {"tx_tcode_buf_abort_cnt"},
306 {"tx_tcode_desc_abort_cnt"},
307 {"tx_tcode_parity_err_cnt"},
308 {"tx_tcode_link_loss_cnt"},
309 {"tx_tcode_list_proc_err_cnt"},
310 {"rx_tcode_parity_err_cnt"},
311 {"rx_tcode_abort_cnt"},
312 {"rx_tcode_parity_abort_cnt"},
313 {"rx_tcode_rda_fail_cnt"},
314 {"rx_tcode_unkn_prot_cnt"},
315 {"rx_tcode_fcs_err_cnt"},
316 {"rx_tcode_buf_size_err_cnt"},
317 {"rx_tcode_rxd_corrupt_cnt"},
318 {"rx_tcode_unkn_err_cnt"},
326 {"mac_tmac_err_cnt"},
327 {"mac_rmac_err_cnt"},
328 {"xgxs_txgxs_err_cnt"},
329 {"xgxs_rxgxs_err_cnt"},
331 {"prc_pcix_err_cnt"},
338 #define S2IO_XENA_STAT_LEN sizeof(ethtool_xena_stats_keys)/ ETH_GSTRING_LEN
339 #define S2IO_ENHANCED_STAT_LEN sizeof(ethtool_enhanced_stats_keys)/ \
341 #define S2IO_DRIVER_STAT_LEN sizeof(ethtool_driver_stats_keys)/ ETH_GSTRING_LEN
343 #define XFRAME_I_STAT_LEN (S2IO_XENA_STAT_LEN + S2IO_DRIVER_STAT_LEN )
344 #define XFRAME_II_STAT_LEN (XFRAME_I_STAT_LEN + S2IO_ENHANCED_STAT_LEN )
346 #define XFRAME_I_STAT_STRINGS_LEN ( XFRAME_I_STAT_LEN * ETH_GSTRING_LEN )
347 #define XFRAME_II_STAT_STRINGS_LEN ( XFRAME_II_STAT_LEN * ETH_GSTRING_LEN )
349 #define S2IO_TEST_LEN sizeof(s2io_gstrings) / ETH_GSTRING_LEN
350 #define S2IO_STRINGS_LEN S2IO_TEST_LEN * ETH_GSTRING_LEN
352 #define S2IO_TIMER_CONF(timer, handle, arg, exp) \
353 init_timer(&timer); \
354 timer.function = handle; \
355 timer.data = (unsigned long) arg; \
356 mod_timer(&timer, (jiffies + exp)) \
358 /* copy mac addr to def_mac_addr array */
359 static void do_s2io_copy_mac_addr(struct s2io_nic *sp, int offset, u64 mac_addr)
361 sp->def_mac_addr[offset].mac_addr[5] = (u8) (mac_addr);
362 sp->def_mac_addr[offset].mac_addr[4] = (u8) (mac_addr >> 8);
363 sp->def_mac_addr[offset].mac_addr[3] = (u8) (mac_addr >> 16);
364 sp->def_mac_addr[offset].mac_addr[2] = (u8) (mac_addr >> 24);
365 sp->def_mac_addr[offset].mac_addr[1] = (u8) (mac_addr >> 32);
366 sp->def_mac_addr[offset].mac_addr[0] = (u8) (mac_addr >> 40);
369 static void s2io_vlan_rx_register(struct net_device *dev,
370 struct vlan_group *grp)
372 struct s2io_nic *nic = dev->priv;
375 spin_lock_irqsave(&nic->tx_lock, flags);
377 spin_unlock_irqrestore(&nic->tx_lock, flags);
380 /* A flag indicating whether 'RX_PA_CFG_STRIP_VLAN_TAG' bit is set or not */
381 static int vlan_strip_flag;
384 * Constants to be programmed into the Xena's registers, to configure
389 static const u64 herc_act_dtx_cfg[] = {
391 0x8000051536750000ULL, 0x80000515367500E0ULL,
393 0x8000051536750004ULL, 0x80000515367500E4ULL,
395 0x80010515003F0000ULL, 0x80010515003F00E0ULL,
397 0x80010515003F0004ULL, 0x80010515003F00E4ULL,
399 0x801205150D440000ULL, 0x801205150D4400E0ULL,
401 0x801205150D440004ULL, 0x801205150D4400E4ULL,
403 0x80020515F2100000ULL, 0x80020515F21000E0ULL,
405 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
410 static const u64 xena_dtx_cfg[] = {
412 0x8000051500000000ULL, 0x80000515000000E0ULL,
414 0x80000515D9350004ULL, 0x80000515D93500E4ULL,
416 0x8001051500000000ULL, 0x80010515000000E0ULL,
418 0x80010515001E0004ULL, 0x80010515001E00E4ULL,
420 0x8002051500000000ULL, 0x80020515000000E0ULL,
422 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
427 * Constants for Fixing the MacAddress problem seen mostly on
430 static const u64 fix_mac[] = {
431 0x0060000000000000ULL, 0x0060600000000000ULL,
432 0x0040600000000000ULL, 0x0000600000000000ULL,
433 0x0020600000000000ULL, 0x0060600000000000ULL,
434 0x0020600000000000ULL, 0x0060600000000000ULL,
435 0x0020600000000000ULL, 0x0060600000000000ULL,
436 0x0020600000000000ULL, 0x0060600000000000ULL,
437 0x0020600000000000ULL, 0x0060600000000000ULL,
438 0x0020600000000000ULL, 0x0060600000000000ULL,
439 0x0020600000000000ULL, 0x0060600000000000ULL,
440 0x0020600000000000ULL, 0x0060600000000000ULL,
441 0x0020600000000000ULL, 0x0060600000000000ULL,
442 0x0020600000000000ULL, 0x0060600000000000ULL,
443 0x0020600000000000ULL, 0x0000600000000000ULL,
444 0x0040600000000000ULL, 0x0060600000000000ULL,
448 MODULE_LICENSE("GPL");
449 MODULE_VERSION(DRV_VERSION);
452 /* Module Loadable parameters. */
453 S2IO_PARM_INT(tx_fifo_num, 1);
454 S2IO_PARM_INT(rx_ring_num, 1);
457 S2IO_PARM_INT(rx_ring_mode, 1);
458 S2IO_PARM_INT(use_continuous_tx_intrs, 1);
459 S2IO_PARM_INT(rmac_pause_time, 0x100);
460 S2IO_PARM_INT(mc_pause_threshold_q0q3, 187);
461 S2IO_PARM_INT(mc_pause_threshold_q4q7, 187);
462 S2IO_PARM_INT(shared_splits, 0);
463 S2IO_PARM_INT(tmac_util_period, 5);
464 S2IO_PARM_INT(rmac_util_period, 5);
465 S2IO_PARM_INT(l3l4hdr_size, 128);
466 /* Frequency of Rx desc syncs expressed as power of 2 */
467 S2IO_PARM_INT(rxsync_frequency, 3);
468 /* Interrupt type. Values can be 0(INTA), 2(MSI_X) */
469 S2IO_PARM_INT(intr_type, 2);
470 /* Large receive offload feature */
471 static unsigned int lro_enable;
472 module_param_named(lro, lro_enable, uint, 0);
474 /* Max pkts to be aggregated by LRO at one time. If not specified,
475 * aggregation happens until we hit max IP pkt size(64K)
477 S2IO_PARM_INT(lro_max_pkts, 0xFFFF);
478 S2IO_PARM_INT(indicate_max_pkts, 0);
480 S2IO_PARM_INT(napi, 1);
481 S2IO_PARM_INT(ufo, 0);
482 S2IO_PARM_INT(vlan_tag_strip, NO_STRIP_IN_PROMISC);
484 static unsigned int tx_fifo_len[MAX_TX_FIFOS] =
485 {DEFAULT_FIFO_0_LEN, [1 ...(MAX_TX_FIFOS - 1)] = DEFAULT_FIFO_1_7_LEN};
486 static unsigned int rx_ring_sz[MAX_RX_RINGS] =
487 {[0 ...(MAX_RX_RINGS - 1)] = SMALL_BLK_CNT};
488 static unsigned int rts_frm_len[MAX_RX_RINGS] =
489 {[0 ...(MAX_RX_RINGS - 1)] = 0 };
491 module_param_array(tx_fifo_len, uint, NULL, 0);
492 module_param_array(rx_ring_sz, uint, NULL, 0);
493 module_param_array(rts_frm_len, uint, NULL, 0);
497 * This table lists all the devices that this driver supports.
499 static struct pci_device_id s2io_tbl[] __devinitdata = {
500 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_WIN,
501 PCI_ANY_ID, PCI_ANY_ID},
502 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_S2IO_UNI,
503 PCI_ANY_ID, PCI_ANY_ID},
504 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_WIN,
505 PCI_ANY_ID, PCI_ANY_ID},
506 {PCI_VENDOR_ID_S2IO, PCI_DEVICE_ID_HERC_UNI,
507 PCI_ANY_ID, PCI_ANY_ID},
511 MODULE_DEVICE_TABLE(pci, s2io_tbl);
513 static struct pci_error_handlers s2io_err_handler = {
514 .error_detected = s2io_io_error_detected,
515 .slot_reset = s2io_io_slot_reset,
516 .resume = s2io_io_resume,
519 static struct pci_driver s2io_driver = {
521 .id_table = s2io_tbl,
522 .probe = s2io_init_nic,
523 .remove = __devexit_p(s2io_rem_nic),
524 .err_handler = &s2io_err_handler,
527 /* A simplifier macro used both by init and free shared_mem Fns(). */
528 #define TXD_MEM_PAGE_CNT(len, per_each) ((len+per_each - 1) / per_each)
531 * init_shared_mem - Allocation and Initialization of Memory
532 * @nic: Device private variable.
533 * Description: The function allocates all the memory areas shared
534 * between the NIC and the driver. This includes Tx descriptors,
535 * Rx descriptors and the statistics block.
538 static int init_shared_mem(struct s2io_nic *nic)
541 void *tmp_v_addr, *tmp_v_addr_next;
542 dma_addr_t tmp_p_addr, tmp_p_addr_next;
543 struct RxD_block *pre_rxd_blk = NULL;
545 int lst_size, lst_per_page;
546 struct net_device *dev = nic->dev;
550 struct mac_info *mac_control;
551 struct config_param *config;
552 unsigned long long mem_allocated = 0;
554 mac_control = &nic->mac_control;
555 config = &nic->config;
558 /* Allocation and initialization of TXDLs in FIOFs */
560 for (i = 0; i < config->tx_fifo_num; i++) {
561 size += config->tx_cfg[i].fifo_len;
563 if (size > MAX_AVAILABLE_TXDS) {
564 DBG_PRINT(ERR_DBG, "s2io: Requested TxDs too high, ");
565 DBG_PRINT(ERR_DBG, "Requested: %d, max supported: 8192\n", size);
569 lst_size = (sizeof(struct TxD) * config->max_txds);
570 lst_per_page = PAGE_SIZE / lst_size;
572 for (i = 0; i < config->tx_fifo_num; i++) {
573 int fifo_len = config->tx_cfg[i].fifo_len;
574 int list_holder_size = fifo_len * sizeof(struct list_info_hold);
575 mac_control->fifos[i].list_info = kzalloc(list_holder_size,
577 if (!mac_control->fifos[i].list_info) {
579 "Malloc failed for list_info\n");
582 mem_allocated += list_holder_size;
584 for (i = 0; i < config->tx_fifo_num; i++) {
585 int page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
587 mac_control->fifos[i].tx_curr_put_info.offset = 0;
588 mac_control->fifos[i].tx_curr_put_info.fifo_len =
589 config->tx_cfg[i].fifo_len - 1;
590 mac_control->fifos[i].tx_curr_get_info.offset = 0;
591 mac_control->fifos[i].tx_curr_get_info.fifo_len =
592 config->tx_cfg[i].fifo_len - 1;
593 mac_control->fifos[i].fifo_no = i;
594 mac_control->fifos[i].nic = nic;
595 mac_control->fifos[i].max_txds = MAX_SKB_FRAGS + 2;
597 for (j = 0; j < page_num; j++) {
601 tmp_v = pci_alloc_consistent(nic->pdev,
605 "pci_alloc_consistent ");
606 DBG_PRINT(INFO_DBG, "failed for TxDL\n");
609 /* If we got a zero DMA address(can happen on
610 * certain platforms like PPC), reallocate.
611 * Store virtual address of page we don't want,
615 mac_control->zerodma_virt_addr = tmp_v;
617 "%s: Zero DMA address for TxDL. ", dev->name);
619 "Virtual address %p\n", tmp_v);
620 tmp_v = pci_alloc_consistent(nic->pdev,
624 "pci_alloc_consistent ");
625 DBG_PRINT(INFO_DBG, "failed for TxDL\n");
628 mem_allocated += PAGE_SIZE;
630 while (k < lst_per_page) {
631 int l = (j * lst_per_page) + k;
632 if (l == config->tx_cfg[i].fifo_len)
634 mac_control->fifos[i].list_info[l].list_virt_addr =
635 tmp_v + (k * lst_size);
636 mac_control->fifos[i].list_info[l].list_phy_addr =
637 tmp_p + (k * lst_size);
643 nic->ufo_in_band_v = kcalloc(size, sizeof(u64), GFP_KERNEL);
644 if (!nic->ufo_in_band_v)
646 mem_allocated += (size * sizeof(u64));
648 /* Allocation and initialization of RXDs in Rings */
650 for (i = 0; i < config->rx_ring_num; i++) {
651 if (config->rx_cfg[i].num_rxd %
652 (rxd_count[nic->rxd_mode] + 1)) {
653 DBG_PRINT(ERR_DBG, "%s: RxD count of ", dev->name);
654 DBG_PRINT(ERR_DBG, "Ring%d is not a multiple of ",
656 DBG_PRINT(ERR_DBG, "RxDs per Block");
659 size += config->rx_cfg[i].num_rxd;
660 mac_control->rings[i].block_count =
661 config->rx_cfg[i].num_rxd /
662 (rxd_count[nic->rxd_mode] + 1 );
663 mac_control->rings[i].pkt_cnt = config->rx_cfg[i].num_rxd -
664 mac_control->rings[i].block_count;
666 if (nic->rxd_mode == RXD_MODE_1)
667 size = (size * (sizeof(struct RxD1)));
669 size = (size * (sizeof(struct RxD3)));
671 for (i = 0; i < config->rx_ring_num; i++) {
672 mac_control->rings[i].rx_curr_get_info.block_index = 0;
673 mac_control->rings[i].rx_curr_get_info.offset = 0;
674 mac_control->rings[i].rx_curr_get_info.ring_len =
675 config->rx_cfg[i].num_rxd - 1;
676 mac_control->rings[i].rx_curr_put_info.block_index = 0;
677 mac_control->rings[i].rx_curr_put_info.offset = 0;
678 mac_control->rings[i].rx_curr_put_info.ring_len =
679 config->rx_cfg[i].num_rxd - 1;
680 mac_control->rings[i].nic = nic;
681 mac_control->rings[i].ring_no = i;
683 blk_cnt = config->rx_cfg[i].num_rxd /
684 (rxd_count[nic->rxd_mode] + 1);
685 /* Allocating all the Rx blocks */
686 for (j = 0; j < blk_cnt; j++) {
687 struct rx_block_info *rx_blocks;
690 rx_blocks = &mac_control->rings[i].rx_blocks[j];
691 size = SIZE_OF_BLOCK; //size is always page size
692 tmp_v_addr = pci_alloc_consistent(nic->pdev, size,
694 if (tmp_v_addr == NULL) {
696 * In case of failure, free_shared_mem()
697 * is called, which should free any
698 * memory that was alloced till the
701 rx_blocks->block_virt_addr = tmp_v_addr;
704 mem_allocated += size;
705 memset(tmp_v_addr, 0, size);
706 rx_blocks->block_virt_addr = tmp_v_addr;
707 rx_blocks->block_dma_addr = tmp_p_addr;
708 rx_blocks->rxds = kmalloc(sizeof(struct rxd_info)*
709 rxd_count[nic->rxd_mode],
711 if (!rx_blocks->rxds)
714 (sizeof(struct rxd_info)* rxd_count[nic->rxd_mode]);
715 for (l=0; l<rxd_count[nic->rxd_mode];l++) {
716 rx_blocks->rxds[l].virt_addr =
717 rx_blocks->block_virt_addr +
718 (rxd_size[nic->rxd_mode] * l);
719 rx_blocks->rxds[l].dma_addr =
720 rx_blocks->block_dma_addr +
721 (rxd_size[nic->rxd_mode] * l);
724 /* Interlinking all Rx Blocks */
725 for (j = 0; j < blk_cnt; j++) {
727 mac_control->rings[i].rx_blocks[j].block_virt_addr;
729 mac_control->rings[i].rx_blocks[(j + 1) %
730 blk_cnt].block_virt_addr;
732 mac_control->rings[i].rx_blocks[j].block_dma_addr;
734 mac_control->rings[i].rx_blocks[(j + 1) %
735 blk_cnt].block_dma_addr;
737 pre_rxd_blk = (struct RxD_block *) tmp_v_addr;
738 pre_rxd_blk->reserved_2_pNext_RxD_block =
739 (unsigned long) tmp_v_addr_next;
740 pre_rxd_blk->pNext_RxD_Blk_physical =
741 (u64) tmp_p_addr_next;
744 if (nic->rxd_mode == RXD_MODE_3B) {
746 * Allocation of Storages for buffer addresses in 2BUFF mode
747 * and the buffers as well.
749 for (i = 0; i < config->rx_ring_num; i++) {
750 blk_cnt = config->rx_cfg[i].num_rxd /
751 (rxd_count[nic->rxd_mode]+ 1);
752 mac_control->rings[i].ba =
753 kmalloc((sizeof(struct buffAdd *) * blk_cnt),
755 if (!mac_control->rings[i].ba)
757 mem_allocated +=(sizeof(struct buffAdd *) * blk_cnt);
758 for (j = 0; j < blk_cnt; j++) {
760 mac_control->rings[i].ba[j] =
761 kmalloc((sizeof(struct buffAdd) *
762 (rxd_count[nic->rxd_mode] + 1)),
764 if (!mac_control->rings[i].ba[j])
766 mem_allocated += (sizeof(struct buffAdd) * \
767 (rxd_count[nic->rxd_mode] + 1));
768 while (k != rxd_count[nic->rxd_mode]) {
769 ba = &mac_control->rings[i].ba[j][k];
771 ba->ba_0_org = (void *) kmalloc
772 (BUF0_LEN + ALIGN_SIZE, GFP_KERNEL);
776 (BUF0_LEN + ALIGN_SIZE);
777 tmp = (unsigned long)ba->ba_0_org;
779 tmp &= ~((unsigned long) ALIGN_SIZE);
780 ba->ba_0 = (void *) tmp;
782 ba->ba_1_org = (void *) kmalloc
783 (BUF1_LEN + ALIGN_SIZE, GFP_KERNEL);
787 += (BUF1_LEN + ALIGN_SIZE);
788 tmp = (unsigned long) ba->ba_1_org;
790 tmp &= ~((unsigned long) ALIGN_SIZE);
791 ba->ba_1 = (void *) tmp;
798 /* Allocation and initialization of Statistics block */
799 size = sizeof(struct stat_block);
800 mac_control->stats_mem = pci_alloc_consistent
801 (nic->pdev, size, &mac_control->stats_mem_phy);
803 if (!mac_control->stats_mem) {
805 * In case of failure, free_shared_mem() is called, which
806 * should free any memory that was alloced till the
811 mem_allocated += size;
812 mac_control->stats_mem_sz = size;
814 tmp_v_addr = mac_control->stats_mem;
815 mac_control->stats_info = (struct stat_block *) tmp_v_addr;
816 memset(tmp_v_addr, 0, size);
817 DBG_PRINT(INIT_DBG, "%s:Ring Mem PHY: 0x%llx\n", dev->name,
818 (unsigned long long) tmp_p_addr);
819 mac_control->stats_info->sw_stat.mem_allocated += mem_allocated;
824 * free_shared_mem - Free the allocated Memory
825 * @nic: Device private variable.
826 * Description: This function is to free all memory locations allocated by
827 * the init_shared_mem() function and return it to the kernel.
830 static void free_shared_mem(struct s2io_nic *nic)
832 int i, j, blk_cnt, size;
835 dma_addr_t tmp_p_addr;
836 struct mac_info *mac_control;
837 struct config_param *config;
838 int lst_size, lst_per_page;
839 struct net_device *dev;
847 mac_control = &nic->mac_control;
848 config = &nic->config;
850 lst_size = (sizeof(struct TxD) * config->max_txds);
851 lst_per_page = PAGE_SIZE / lst_size;
853 for (i = 0; i < config->tx_fifo_num; i++) {
854 ufo_size += config->tx_cfg[i].fifo_len;
855 page_num = TXD_MEM_PAGE_CNT(config->tx_cfg[i].fifo_len,
857 for (j = 0; j < page_num; j++) {
858 int mem_blks = (j * lst_per_page);
859 if (!mac_control->fifos[i].list_info)
861 if (!mac_control->fifos[i].list_info[mem_blks].
864 pci_free_consistent(nic->pdev, PAGE_SIZE,
865 mac_control->fifos[i].
868 mac_control->fifos[i].
871 nic->mac_control.stats_info->sw_stat.mem_freed
874 /* If we got a zero DMA address during allocation,
877 if (mac_control->zerodma_virt_addr) {
878 pci_free_consistent(nic->pdev, PAGE_SIZE,
879 mac_control->zerodma_virt_addr,
882 "%s: Freeing TxDL with zero DMA addr. ",
884 DBG_PRINT(INIT_DBG, "Virtual address %p\n",
885 mac_control->zerodma_virt_addr);
886 nic->mac_control.stats_info->sw_stat.mem_freed
889 kfree(mac_control->fifos[i].list_info);
890 nic->mac_control.stats_info->sw_stat.mem_freed +=
891 (nic->config.tx_cfg[i].fifo_len *sizeof(struct list_info_hold));
894 size = SIZE_OF_BLOCK;
895 for (i = 0; i < config->rx_ring_num; i++) {
896 blk_cnt = mac_control->rings[i].block_count;
897 for (j = 0; j < blk_cnt; j++) {
898 tmp_v_addr = mac_control->rings[i].rx_blocks[j].
900 tmp_p_addr = mac_control->rings[i].rx_blocks[j].
902 if (tmp_v_addr == NULL)
904 pci_free_consistent(nic->pdev, size,
905 tmp_v_addr, tmp_p_addr);
906 nic->mac_control.stats_info->sw_stat.mem_freed += size;
907 kfree(mac_control->rings[i].rx_blocks[j].rxds);
908 nic->mac_control.stats_info->sw_stat.mem_freed +=
909 ( sizeof(struct rxd_info)* rxd_count[nic->rxd_mode]);
913 if (nic->rxd_mode == RXD_MODE_3B) {
914 /* Freeing buffer storage addresses in 2BUFF mode. */
915 for (i = 0; i < config->rx_ring_num; i++) {
916 blk_cnt = config->rx_cfg[i].num_rxd /
917 (rxd_count[nic->rxd_mode] + 1);
918 for (j = 0; j < blk_cnt; j++) {
920 if (!mac_control->rings[i].ba[j])
922 while (k != rxd_count[nic->rxd_mode]) {
924 &mac_control->rings[i].ba[j][k];
926 nic->mac_control.stats_info->sw_stat.\
927 mem_freed += (BUF0_LEN + ALIGN_SIZE);
929 nic->mac_control.stats_info->sw_stat.\
930 mem_freed += (BUF1_LEN + ALIGN_SIZE);
933 kfree(mac_control->rings[i].ba[j]);
934 nic->mac_control.stats_info->sw_stat.mem_freed +=
935 (sizeof(struct buffAdd) *
936 (rxd_count[nic->rxd_mode] + 1));
938 kfree(mac_control->rings[i].ba);
939 nic->mac_control.stats_info->sw_stat.mem_freed +=
940 (sizeof(struct buffAdd *) * blk_cnt);
944 if (mac_control->stats_mem) {
945 pci_free_consistent(nic->pdev,
946 mac_control->stats_mem_sz,
947 mac_control->stats_mem,
948 mac_control->stats_mem_phy);
949 nic->mac_control.stats_info->sw_stat.mem_freed +=
950 mac_control->stats_mem_sz;
952 if (nic->ufo_in_band_v) {
953 kfree(nic->ufo_in_band_v);
954 nic->mac_control.stats_info->sw_stat.mem_freed
955 += (ufo_size * sizeof(u64));
960 * s2io_verify_pci_mode -
963 static int s2io_verify_pci_mode(struct s2io_nic *nic)
965 struct XENA_dev_config __iomem *bar0 = nic->bar0;
966 register u64 val64 = 0;
969 val64 = readq(&bar0->pci_mode);
970 mode = (u8)GET_PCI_MODE(val64);
972 if ( val64 & PCI_MODE_UNKNOWN_MODE)
973 return -1; /* Unknown PCI mode */
977 #define NEC_VENID 0x1033
978 #define NEC_DEVID 0x0125
979 static int s2io_on_nec_bridge(struct pci_dev *s2io_pdev)
981 struct pci_dev *tdev = NULL;
982 while ((tdev = pci_get_device(PCI_ANY_ID, PCI_ANY_ID, tdev)) != NULL) {
983 if (tdev->vendor == NEC_VENID && tdev->device == NEC_DEVID) {
984 if (tdev->bus == s2io_pdev->bus->parent)
992 static int bus_speed[8] = {33, 133, 133, 200, 266, 133, 200, 266};
994 * s2io_print_pci_mode -
996 static int s2io_print_pci_mode(struct s2io_nic *nic)
998 struct XENA_dev_config __iomem *bar0 = nic->bar0;
999 register u64 val64 = 0;
1001 struct config_param *config = &nic->config;
1003 val64 = readq(&bar0->pci_mode);
1004 mode = (u8)GET_PCI_MODE(val64);
1006 if ( val64 & PCI_MODE_UNKNOWN_MODE)
1007 return -1; /* Unknown PCI mode */
1009 config->bus_speed = bus_speed[mode];
1011 if (s2io_on_nec_bridge(nic->pdev)) {
1012 DBG_PRINT(ERR_DBG, "%s: Device is on PCI-E bus\n",
1017 if (val64 & PCI_MODE_32_BITS) {
1018 DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
1020 DBG_PRINT(ERR_DBG, "%s: Device is on 64 bit ", nic->dev->name);
1024 case PCI_MODE_PCI_33:
1025 DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
1027 case PCI_MODE_PCI_66:
1028 DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
1030 case PCI_MODE_PCIX_M1_66:
1031 DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
1033 case PCI_MODE_PCIX_M1_100:
1034 DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
1036 case PCI_MODE_PCIX_M1_133:
1037 DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
1039 case PCI_MODE_PCIX_M2_66:
1040 DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
1042 case PCI_MODE_PCIX_M2_100:
1043 DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
1045 case PCI_MODE_PCIX_M2_133:
1046 DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
1049 return -1; /* Unsupported bus speed */
1056 * init_nic - Initialization of hardware
1057 * @nic: device peivate variable
1058 * Description: The function sequentially configures every block
1059 * of the H/W from their reset values.
1060 * Return Value: SUCCESS on success and
1061 * '-1' on failure (endian settings incorrect).
1064 static int init_nic(struct s2io_nic *nic)
1066 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1067 struct net_device *dev = nic->dev;
1068 register u64 val64 = 0;
1072 struct mac_info *mac_control;
1073 struct config_param *config;
1075 unsigned long long mem_share;
1078 mac_control = &nic->mac_control;
1079 config = &nic->config;
1081 /* to set the swapper controle on the card */
1082 if(s2io_set_swapper(nic)) {
1083 DBG_PRINT(ERR_DBG,"ERROR: Setting Swapper failed\n");
1088 * Herc requires EOI to be removed from reset before XGXS, so..
1090 if (nic->device_type & XFRAME_II_DEVICE) {
1091 val64 = 0xA500000000ULL;
1092 writeq(val64, &bar0->sw_reset);
1094 val64 = readq(&bar0->sw_reset);
1097 /* Remove XGXS from reset state */
1099 writeq(val64, &bar0->sw_reset);
1101 val64 = readq(&bar0->sw_reset);
1103 /* Enable Receiving broadcasts */
1104 add = &bar0->mac_cfg;
1105 val64 = readq(&bar0->mac_cfg);
1106 val64 |= MAC_RMAC_BCAST_ENABLE;
1107 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1108 writel((u32) val64, add);
1109 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1110 writel((u32) (val64 >> 32), (add + 4));
1112 /* Read registers in all blocks */
1113 val64 = readq(&bar0->mac_int_mask);
1114 val64 = readq(&bar0->mc_int_mask);
1115 val64 = readq(&bar0->xgxs_int_mask);
1119 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
1121 if (nic->device_type & XFRAME_II_DEVICE) {
1122 while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
1123 SPECIAL_REG_WRITE(herc_act_dtx_cfg[dtx_cnt],
1124 &bar0->dtx_control, UF);
1126 msleep(1); /* Necessary!! */
1130 while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
1131 SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
1132 &bar0->dtx_control, UF);
1133 val64 = readq(&bar0->dtx_control);
1138 /* Tx DMA Initialization */
1140 writeq(val64, &bar0->tx_fifo_partition_0);
1141 writeq(val64, &bar0->tx_fifo_partition_1);
1142 writeq(val64, &bar0->tx_fifo_partition_2);
1143 writeq(val64, &bar0->tx_fifo_partition_3);
1146 for (i = 0, j = 0; i < config->tx_fifo_num; i++) {
1148 vBIT(config->tx_cfg[i].fifo_len - 1, ((i * 32) + 19),
1149 13) | vBIT(config->tx_cfg[i].fifo_priority,
1152 if (i == (config->tx_fifo_num - 1)) {
1159 writeq(val64, &bar0->tx_fifo_partition_0);
1163 writeq(val64, &bar0->tx_fifo_partition_1);
1167 writeq(val64, &bar0->tx_fifo_partition_2);
1171 writeq(val64, &bar0->tx_fifo_partition_3);
1177 * Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug
1178 * SXE-008 TRANSMIT DMA ARBITRATION ISSUE.
1180 if ((nic->device_type == XFRAME_I_DEVICE) &&
1181 (nic->pdev->revision < 4))
1182 writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable);
1184 val64 = readq(&bar0->tx_fifo_partition_0);
1185 DBG_PRINT(INIT_DBG, "Fifo partition at: 0x%p is: 0x%llx\n",
1186 &bar0->tx_fifo_partition_0, (unsigned long long) val64);
1189 * Initialization of Tx_PA_CONFIG register to ignore packet
1190 * integrity checking.
1192 val64 = readq(&bar0->tx_pa_cfg);
1193 val64 |= TX_PA_CFG_IGNORE_FRM_ERR | TX_PA_CFG_IGNORE_SNAP_OUI |
1194 TX_PA_CFG_IGNORE_LLC_CTRL | TX_PA_CFG_IGNORE_L2_ERR;
1195 writeq(val64, &bar0->tx_pa_cfg);
1197 /* Rx DMA intialization. */
1199 for (i = 0; i < config->rx_ring_num; i++) {
1201 vBIT(config->rx_cfg[i].ring_priority, (5 + (i * 8)),
1204 writeq(val64, &bar0->rx_queue_priority);
1207 * Allocating equal share of memory to all the
1211 if (nic->device_type & XFRAME_II_DEVICE)
1216 for (i = 0; i < config->rx_ring_num; i++) {
1219 mem_share = (mem_size / config->rx_ring_num +
1220 mem_size % config->rx_ring_num);
1221 val64 |= RX_QUEUE_CFG_Q0_SZ(mem_share);
1224 mem_share = (mem_size / config->rx_ring_num);
1225 val64 |= RX_QUEUE_CFG_Q1_SZ(mem_share);
1228 mem_share = (mem_size / config->rx_ring_num);
1229 val64 |= RX_QUEUE_CFG_Q2_SZ(mem_share);
1232 mem_share = (mem_size / config->rx_ring_num);
1233 val64 |= RX_QUEUE_CFG_Q3_SZ(mem_share);
1236 mem_share = (mem_size / config->rx_ring_num);
1237 val64 |= RX_QUEUE_CFG_Q4_SZ(mem_share);
1240 mem_share = (mem_size / config->rx_ring_num);
1241 val64 |= RX_QUEUE_CFG_Q5_SZ(mem_share);
1244 mem_share = (mem_size / config->rx_ring_num);
1245 val64 |= RX_QUEUE_CFG_Q6_SZ(mem_share);
1248 mem_share = (mem_size / config->rx_ring_num);
1249 val64 |= RX_QUEUE_CFG_Q7_SZ(mem_share);
1253 writeq(val64, &bar0->rx_queue_cfg);
1256 * Filling Tx round robin registers
1257 * as per the number of FIFOs
1259 switch (config->tx_fifo_num) {
1261 val64 = 0x0000000000000000ULL;
1262 writeq(val64, &bar0->tx_w_round_robin_0);
1263 writeq(val64, &bar0->tx_w_round_robin_1);
1264 writeq(val64, &bar0->tx_w_round_robin_2);
1265 writeq(val64, &bar0->tx_w_round_robin_3);
1266 writeq(val64, &bar0->tx_w_round_robin_4);
1269 val64 = 0x0000010000010000ULL;
1270 writeq(val64, &bar0->tx_w_round_robin_0);
1271 val64 = 0x0100000100000100ULL;
1272 writeq(val64, &bar0->tx_w_round_robin_1);
1273 val64 = 0x0001000001000001ULL;
1274 writeq(val64, &bar0->tx_w_round_robin_2);
1275 val64 = 0x0000010000010000ULL;
1276 writeq(val64, &bar0->tx_w_round_robin_3);
1277 val64 = 0x0100000000000000ULL;
1278 writeq(val64, &bar0->tx_w_round_robin_4);
1281 val64 = 0x0001000102000001ULL;
1282 writeq(val64, &bar0->tx_w_round_robin_0);
1283 val64 = 0x0001020000010001ULL;
1284 writeq(val64, &bar0->tx_w_round_robin_1);
1285 val64 = 0x0200000100010200ULL;
1286 writeq(val64, &bar0->tx_w_round_robin_2);
1287 val64 = 0x0001000102000001ULL;
1288 writeq(val64, &bar0->tx_w_round_robin_3);
1289 val64 = 0x0001020000000000ULL;
1290 writeq(val64, &bar0->tx_w_round_robin_4);
1293 val64 = 0x0001020300010200ULL;
1294 writeq(val64, &bar0->tx_w_round_robin_0);
1295 val64 = 0x0100000102030001ULL;
1296 writeq(val64, &bar0->tx_w_round_robin_1);
1297 val64 = 0x0200010000010203ULL;
1298 writeq(val64, &bar0->tx_w_round_robin_2);
1299 val64 = 0x0001020001000001ULL;
1300 writeq(val64, &bar0->tx_w_round_robin_3);
1301 val64 = 0x0203000100000000ULL;
1302 writeq(val64, &bar0->tx_w_round_robin_4);
1305 val64 = 0x0001000203000102ULL;
1306 writeq(val64, &bar0->tx_w_round_robin_0);
1307 val64 = 0x0001020001030004ULL;
1308 writeq(val64, &bar0->tx_w_round_robin_1);
1309 val64 = 0x0001000203000102ULL;
1310 writeq(val64, &bar0->tx_w_round_robin_2);
1311 val64 = 0x0001020001030004ULL;
1312 writeq(val64, &bar0->tx_w_round_robin_3);
1313 val64 = 0x0001000000000000ULL;
1314 writeq(val64, &bar0->tx_w_round_robin_4);
1317 val64 = 0x0001020304000102ULL;
1318 writeq(val64, &bar0->tx_w_round_robin_0);
1319 val64 = 0x0304050001020001ULL;
1320 writeq(val64, &bar0->tx_w_round_robin_1);
1321 val64 = 0x0203000100000102ULL;
1322 writeq(val64, &bar0->tx_w_round_robin_2);
1323 val64 = 0x0304000102030405ULL;
1324 writeq(val64, &bar0->tx_w_round_robin_3);
1325 val64 = 0x0001000200000000ULL;
1326 writeq(val64, &bar0->tx_w_round_robin_4);
1329 val64 = 0x0001020001020300ULL;
1330 writeq(val64, &bar0->tx_w_round_robin_0);
1331 val64 = 0x0102030400010203ULL;
1332 writeq(val64, &bar0->tx_w_round_robin_1);
1333 val64 = 0x0405060001020001ULL;
1334 writeq(val64, &bar0->tx_w_round_robin_2);
1335 val64 = 0x0304050000010200ULL;
1336 writeq(val64, &bar0->tx_w_round_robin_3);
1337 val64 = 0x0102030000000000ULL;
1338 writeq(val64, &bar0->tx_w_round_robin_4);
1341 val64 = 0x0001020300040105ULL;
1342 writeq(val64, &bar0->tx_w_round_robin_0);
1343 val64 = 0x0200030106000204ULL;
1344 writeq(val64, &bar0->tx_w_round_robin_1);
1345 val64 = 0x0103000502010007ULL;
1346 writeq(val64, &bar0->tx_w_round_robin_2);
1347 val64 = 0x0304010002060500ULL;
1348 writeq(val64, &bar0->tx_w_round_robin_3);
1349 val64 = 0x0103020400000000ULL;
1350 writeq(val64, &bar0->tx_w_round_robin_4);
1354 /* Enable all configured Tx FIFO partitions */
1355 val64 = readq(&bar0->tx_fifo_partition_0);
1356 val64 |= (TX_FIFO_PARTITION_EN);
1357 writeq(val64, &bar0->tx_fifo_partition_0);
1359 /* Filling the Rx round robin registers as per the
1360 * number of Rings and steering based on QoS.
1362 switch (config->rx_ring_num) {
1364 val64 = 0x8080808080808080ULL;
1365 writeq(val64, &bar0->rts_qos_steering);
1368 val64 = 0x0000010000010000ULL;
1369 writeq(val64, &bar0->rx_w_round_robin_0);
1370 val64 = 0x0100000100000100ULL;
1371 writeq(val64, &bar0->rx_w_round_robin_1);
1372 val64 = 0x0001000001000001ULL;
1373 writeq(val64, &bar0->rx_w_round_robin_2);
1374 val64 = 0x0000010000010000ULL;
1375 writeq(val64, &bar0->rx_w_round_robin_3);
1376 val64 = 0x0100000000000000ULL;
1377 writeq(val64, &bar0->rx_w_round_robin_4);
1379 val64 = 0x8080808040404040ULL;
1380 writeq(val64, &bar0->rts_qos_steering);
1383 val64 = 0x0001000102000001ULL;
1384 writeq(val64, &bar0->rx_w_round_robin_0);
1385 val64 = 0x0001020000010001ULL;
1386 writeq(val64, &bar0->rx_w_round_robin_1);
1387 val64 = 0x0200000100010200ULL;
1388 writeq(val64, &bar0->rx_w_round_robin_2);
1389 val64 = 0x0001000102000001ULL;
1390 writeq(val64, &bar0->rx_w_round_robin_3);
1391 val64 = 0x0001020000000000ULL;
1392 writeq(val64, &bar0->rx_w_round_robin_4);
1394 val64 = 0x8080804040402020ULL;
1395 writeq(val64, &bar0->rts_qos_steering);
1398 val64 = 0x0001020300010200ULL;
1399 writeq(val64, &bar0->rx_w_round_robin_0);
1400 val64 = 0x0100000102030001ULL;
1401 writeq(val64, &bar0->rx_w_round_robin_1);
1402 val64 = 0x0200010000010203ULL;
1403 writeq(val64, &bar0->rx_w_round_robin_2);
1404 val64 = 0x0001020001000001ULL;
1405 writeq(val64, &bar0->rx_w_round_robin_3);
1406 val64 = 0x0203000100000000ULL;
1407 writeq(val64, &bar0->rx_w_round_robin_4);
1409 val64 = 0x8080404020201010ULL;
1410 writeq(val64, &bar0->rts_qos_steering);
1413 val64 = 0x0001000203000102ULL;
1414 writeq(val64, &bar0->rx_w_round_robin_0);
1415 val64 = 0x0001020001030004ULL;
1416 writeq(val64, &bar0->rx_w_round_robin_1);
1417 val64 = 0x0001000203000102ULL;
1418 writeq(val64, &bar0->rx_w_round_robin_2);
1419 val64 = 0x0001020001030004ULL;
1420 writeq(val64, &bar0->rx_w_round_robin_3);
1421 val64 = 0x0001000000000000ULL;
1422 writeq(val64, &bar0->rx_w_round_robin_4);
1424 val64 = 0x8080404020201008ULL;
1425 writeq(val64, &bar0->rts_qos_steering);
1428 val64 = 0x0001020304000102ULL;
1429 writeq(val64, &bar0->rx_w_round_robin_0);
1430 val64 = 0x0304050001020001ULL;
1431 writeq(val64, &bar0->rx_w_round_robin_1);
1432 val64 = 0x0203000100000102ULL;
1433 writeq(val64, &bar0->rx_w_round_robin_2);
1434 val64 = 0x0304000102030405ULL;
1435 writeq(val64, &bar0->rx_w_round_robin_3);
1436 val64 = 0x0001000200000000ULL;
1437 writeq(val64, &bar0->rx_w_round_robin_4);
1439 val64 = 0x8080404020100804ULL;
1440 writeq(val64, &bar0->rts_qos_steering);
1443 val64 = 0x0001020001020300ULL;
1444 writeq(val64, &bar0->rx_w_round_robin_0);
1445 val64 = 0x0102030400010203ULL;
1446 writeq(val64, &bar0->rx_w_round_robin_1);
1447 val64 = 0x0405060001020001ULL;
1448 writeq(val64, &bar0->rx_w_round_robin_2);
1449 val64 = 0x0304050000010200ULL;
1450 writeq(val64, &bar0->rx_w_round_robin_3);
1451 val64 = 0x0102030000000000ULL;
1452 writeq(val64, &bar0->rx_w_round_robin_4);
1454 val64 = 0x8080402010080402ULL;
1455 writeq(val64, &bar0->rts_qos_steering);
1458 val64 = 0x0001020300040105ULL;
1459 writeq(val64, &bar0->rx_w_round_robin_0);
1460 val64 = 0x0200030106000204ULL;
1461 writeq(val64, &bar0->rx_w_round_robin_1);
1462 val64 = 0x0103000502010007ULL;
1463 writeq(val64, &bar0->rx_w_round_robin_2);
1464 val64 = 0x0304010002060500ULL;
1465 writeq(val64, &bar0->rx_w_round_robin_3);
1466 val64 = 0x0103020400000000ULL;
1467 writeq(val64, &bar0->rx_w_round_robin_4);
1469 val64 = 0x8040201008040201ULL;
1470 writeq(val64, &bar0->rts_qos_steering);
1476 for (i = 0; i < 8; i++)
1477 writeq(val64, &bar0->rts_frm_len_n[i]);
1479 /* Set the default rts frame length for the rings configured */
1480 val64 = MAC_RTS_FRM_LEN_SET(dev->mtu+22);
1481 for (i = 0 ; i < config->rx_ring_num ; i++)
1482 writeq(val64, &bar0->rts_frm_len_n[i]);
1484 /* Set the frame length for the configured rings
1485 * desired by the user
1487 for (i = 0; i < config->rx_ring_num; i++) {
1488 /* If rts_frm_len[i] == 0 then it is assumed that user not
1489 * specified frame length steering.
1490 * If the user provides the frame length then program
1491 * the rts_frm_len register for those values or else
1492 * leave it as it is.
1494 if (rts_frm_len[i] != 0) {
1495 writeq(MAC_RTS_FRM_LEN_SET(rts_frm_len[i]),
1496 &bar0->rts_frm_len_n[i]);
1500 /* Disable differentiated services steering logic */
1501 for (i = 0; i < 64; i++) {
1502 if (rts_ds_steer(nic, i, 0) == FAILURE) {
1503 DBG_PRINT(ERR_DBG, "%s: failed rts ds steering",
1505 DBG_PRINT(ERR_DBG, "set on codepoint %d\n", i);
1510 /* Program statistics memory */
1511 writeq(mac_control->stats_mem_phy, &bar0->stat_addr);
1513 if (nic->device_type == XFRAME_II_DEVICE) {
1514 val64 = STAT_BC(0x320);
1515 writeq(val64, &bar0->stat_byte_cnt);
1519 * Initializing the sampling rate for the device to calculate the
1520 * bandwidth utilization.
1522 val64 = MAC_TX_LINK_UTIL_VAL(tmac_util_period) |
1523 MAC_RX_LINK_UTIL_VAL(rmac_util_period);
1524 writeq(val64, &bar0->mac_link_util);
1528 * Initializing the Transmit and Receive Traffic Interrupt
1532 * TTI Initialization. Default Tx timer gets us about
1533 * 250 interrupts per sec. Continuous interrupts are enabled
1536 if (nic->device_type == XFRAME_II_DEVICE) {
1537 int count = (nic->config.bus_speed * 125)/2;
1538 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count);
1541 val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078);
1543 val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) |
1544 TTI_DATA1_MEM_TX_URNG_B(0x10) |
1545 TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN;
1546 if (use_continuous_tx_intrs)
1547 val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
1548 writeq(val64, &bar0->tti_data1_mem);
1550 val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
1551 TTI_DATA2_MEM_TX_UFC_B(0x20) |
1552 TTI_DATA2_MEM_TX_UFC_C(0x40) | TTI_DATA2_MEM_TX_UFC_D(0x80);
1553 writeq(val64, &bar0->tti_data2_mem);
1555 val64 = TTI_CMD_MEM_WE | TTI_CMD_MEM_STROBE_NEW_CMD;
1556 writeq(val64, &bar0->tti_command_mem);
1559 * Once the operation completes, the Strobe bit of the command
1560 * register will be reset. We poll for this particular condition
1561 * We wait for a maximum of 500ms for the operation to complete,
1562 * if it's not complete by then we return error.
1566 val64 = readq(&bar0->tti_command_mem);
1567 if (!(val64 & TTI_CMD_MEM_STROBE_NEW_CMD)) {
1571 DBG_PRINT(ERR_DBG, "%s: TTI init Failed\n",
1579 /* RTI Initialization */
1580 if (nic->device_type == XFRAME_II_DEVICE) {
1582 * Programmed to generate Apprx 500 Intrs per
1585 int count = (nic->config.bus_speed * 125)/4;
1586 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count);
1588 val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF);
1589 val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) |
1590 RTI_DATA1_MEM_RX_URNG_B(0x10) |
1591 RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN;
1593 writeq(val64, &bar0->rti_data1_mem);
1595 val64 = RTI_DATA2_MEM_RX_UFC_A(0x1) |
1596 RTI_DATA2_MEM_RX_UFC_B(0x2) ;
1597 if (nic->config.intr_type == MSI_X)
1598 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x20) | \
1599 RTI_DATA2_MEM_RX_UFC_D(0x40));
1601 val64 |= (RTI_DATA2_MEM_RX_UFC_C(0x40) | \
1602 RTI_DATA2_MEM_RX_UFC_D(0x80));
1603 writeq(val64, &bar0->rti_data2_mem);
1605 for (i = 0; i < config->rx_ring_num; i++) {
1606 val64 = RTI_CMD_MEM_WE | RTI_CMD_MEM_STROBE_NEW_CMD
1607 | RTI_CMD_MEM_OFFSET(i);
1608 writeq(val64, &bar0->rti_command_mem);
1611 * Once the operation completes, the Strobe bit of the
1612 * command register will be reset. We poll for this
1613 * particular condition. We wait for a maximum of 500ms
1614 * for the operation to complete, if it's not complete
1615 * by then we return error.
1619 val64 = readq(&bar0->rti_command_mem);
1620 if (!(val64 & RTI_CMD_MEM_STROBE_NEW_CMD))
1624 DBG_PRINT(ERR_DBG, "%s: RTI init Failed\n",
1634 * Initializing proper values as Pause threshold into all
1635 * the 8 Queues on Rx side.
1637 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q0q3);
1638 writeq(0xffbbffbbffbbffbbULL, &bar0->mc_pause_thresh_q4q7);
1640 /* Disable RMAC PAD STRIPPING */
1641 add = &bar0->mac_cfg;
1642 val64 = readq(&bar0->mac_cfg);
1643 val64 &= ~(MAC_CFG_RMAC_STRIP_PAD);
1644 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1645 writel((u32) (val64), add);
1646 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1647 writel((u32) (val64 >> 32), (add + 4));
1648 val64 = readq(&bar0->mac_cfg);
1650 /* Enable FCS stripping by adapter */
1651 add = &bar0->mac_cfg;
1652 val64 = readq(&bar0->mac_cfg);
1653 val64 |= MAC_CFG_RMAC_STRIP_FCS;
1654 if (nic->device_type == XFRAME_II_DEVICE)
1655 writeq(val64, &bar0->mac_cfg);
1657 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1658 writel((u32) (val64), add);
1659 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
1660 writel((u32) (val64 >> 32), (add + 4));
1664 * Set the time value to be inserted in the pause frame
1665 * generated by xena.
1667 val64 = readq(&bar0->rmac_pause_cfg);
1668 val64 &= ~(RMAC_PAUSE_HG_PTIME(0xffff));
1669 val64 |= RMAC_PAUSE_HG_PTIME(nic->mac_control.rmac_pause_time);
1670 writeq(val64, &bar0->rmac_pause_cfg);
1673 * Set the Threshold Limit for Generating the pause frame
1674 * If the amount of data in any Queue exceeds ratio of
1675 * (mac_control.mc_pause_threshold_q0q3 or q4q7)/256
1676 * pause frame is generated
1679 for (i = 0; i < 4; i++) {
1681 (((u64) 0xFF00 | nic->mac_control.
1682 mc_pause_threshold_q0q3)
1685 writeq(val64, &bar0->mc_pause_thresh_q0q3);
1688 for (i = 0; i < 4; i++) {
1690 (((u64) 0xFF00 | nic->mac_control.
1691 mc_pause_threshold_q4q7)
1694 writeq(val64, &bar0->mc_pause_thresh_q4q7);
1697 * TxDMA will stop Read request if the number of read split has
1698 * exceeded the limit pointed by shared_splits
1700 val64 = readq(&bar0->pic_control);
1701 val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits);
1702 writeq(val64, &bar0->pic_control);
1704 if (nic->config.bus_speed == 266) {
1705 writeq(TXREQTO_VAL(0x7f) | TXREQTO_EN, &bar0->txreqtimeout);
1706 writeq(0x0, &bar0->read_retry_delay);
1707 writeq(0x0, &bar0->write_retry_delay);
1711 * Programming the Herc to split every write transaction
1712 * that does not start on an ADB to reduce disconnects.
1714 if (nic->device_type == XFRAME_II_DEVICE) {
1715 val64 = FAULT_BEHAVIOUR | EXT_REQ_EN |
1716 MISC_LINK_STABILITY_PRD(3);
1717 writeq(val64, &bar0->misc_control);
1718 val64 = readq(&bar0->pic_control2);
1719 val64 &= ~(s2BIT(13)|s2BIT(14)|s2BIT(15));
1720 writeq(val64, &bar0->pic_control2);
1722 if (strstr(nic->product_name, "CX4")) {
1723 val64 = TMAC_AVG_IPG(0x17);
1724 writeq(val64, &bar0->tmac_avg_ipg);
1729 #define LINK_UP_DOWN_INTERRUPT 1
1730 #define MAC_RMAC_ERR_TIMER 2
1732 static int s2io_link_fault_indication(struct s2io_nic *nic)
1734 if (nic->config.intr_type != INTA)
1735 return MAC_RMAC_ERR_TIMER;
1736 if (nic->device_type == XFRAME_II_DEVICE)
1737 return LINK_UP_DOWN_INTERRUPT;
1739 return MAC_RMAC_ERR_TIMER;
1743 * do_s2io_write_bits - update alarm bits in alarm register
1744 * @value: alarm bits
1745 * @flag: interrupt status
1746 * @addr: address value
1747 * Description: update alarm bits in alarm register
1751 static void do_s2io_write_bits(u64 value, int flag, void __iomem *addr)
1755 temp64 = readq(addr);
1757 if(flag == ENABLE_INTRS)
1758 temp64 &= ~((u64) value);
1760 temp64 |= ((u64) value);
1761 writeq(temp64, addr);
1764 static void en_dis_err_alarms(struct s2io_nic *nic, u16 mask, int flag)
1766 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1767 register u64 gen_int_mask = 0;
1769 if (mask & TX_DMA_INTR) {
1771 gen_int_mask |= TXDMA_INT_M;
1773 do_s2io_write_bits(TXDMA_TDA_INT | TXDMA_PFC_INT |
1774 TXDMA_PCC_INT | TXDMA_TTI_INT |
1775 TXDMA_LSO_INT | TXDMA_TPA_INT |
1776 TXDMA_SM_INT, flag, &bar0->txdma_int_mask);
1778 do_s2io_write_bits(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM |
1779 PFC_MISC_0_ERR | PFC_MISC_1_ERR |
1780 PFC_PCIX_ERR | PFC_ECC_SG_ERR, flag,
1781 &bar0->pfc_err_mask);
1783 do_s2io_write_bits(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
1784 TDA_SM1_ERR_ALARM | TDA_Fn_ECC_SG_ERR |
1785 TDA_PCIX_ERR, flag, &bar0->tda_err_mask);
1787 do_s2io_write_bits(PCC_FB_ECC_DB_ERR | PCC_TXB_ECC_DB_ERR |
1788 PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM |
1789 PCC_N_SERR | PCC_6_COF_OV_ERR |
1790 PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR |
1791 PCC_7_LSO_OV_ERR | PCC_FB_ECC_SG_ERR |
1792 PCC_TXB_ECC_SG_ERR, flag, &bar0->pcc_err_mask);
1794 do_s2io_write_bits(TTI_SM_ERR_ALARM | TTI_ECC_SG_ERR |
1795 TTI_ECC_DB_ERR, flag, &bar0->tti_err_mask);
1797 do_s2io_write_bits(LSO6_ABORT | LSO7_ABORT |
1798 LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM |
1799 LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
1800 flag, &bar0->lso_err_mask);
1802 do_s2io_write_bits(TPA_SM_ERR_ALARM | TPA_TX_FRM_DROP,
1803 flag, &bar0->tpa_err_mask);
1805 do_s2io_write_bits(SM_SM_ERR_ALARM, flag, &bar0->sm_err_mask);
1809 if (mask & TX_MAC_INTR) {
1810 gen_int_mask |= TXMAC_INT_M;
1811 do_s2io_write_bits(MAC_INT_STATUS_TMAC_INT, flag,
1812 &bar0->mac_int_mask);
1813 do_s2io_write_bits(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR |
1814 TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR |
1815 TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
1816 flag, &bar0->mac_tmac_err_mask);
1819 if (mask & TX_XGXS_INTR) {
1820 gen_int_mask |= TXXGXS_INT_M;
1821 do_s2io_write_bits(XGXS_INT_STATUS_TXGXS, flag,
1822 &bar0->xgxs_int_mask);
1823 do_s2io_write_bits(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR |
1824 TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
1825 flag, &bar0->xgxs_txgxs_err_mask);
1828 if (mask & RX_DMA_INTR) {
1829 gen_int_mask |= RXDMA_INT_M;
1830 do_s2io_write_bits(RXDMA_INT_RC_INT_M | RXDMA_INT_RPA_INT_M |
1831 RXDMA_INT_RDA_INT_M | RXDMA_INT_RTI_INT_M,
1832 flag, &bar0->rxdma_int_mask);
1833 do_s2io_write_bits(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR |
1834 RC_PRCn_SM_ERR_ALARM | RC_FTC_SM_ERR_ALARM |
1835 RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR |
1836 RC_RDA_FAIL_WR_Rn, flag, &bar0->rc_err_mask);
1837 do_s2io_write_bits(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn |
1838 PRC_PCI_AB_F_WR_Rn | PRC_PCI_DP_RD_Rn |
1839 PRC_PCI_DP_WR_Rn | PRC_PCI_DP_F_WR_Rn, flag,
1840 &bar0->prc_pcix_err_mask);
1841 do_s2io_write_bits(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR |
1842 RPA_ECC_SG_ERR | RPA_ECC_DB_ERR, flag,
1843 &bar0->rpa_err_mask);
1844 do_s2io_write_bits(RDA_RXDn_ECC_DB_ERR | RDA_FRM_ECC_DB_N_AERR |
1845 RDA_SM1_ERR_ALARM | RDA_SM0_ERR_ALARM |
1846 RDA_RXD_ECC_DB_SERR | RDA_RXDn_ECC_SG_ERR |
1847 RDA_FRM_ECC_SG_ERR | RDA_MISC_ERR|RDA_PCIX_ERR,
1848 flag, &bar0->rda_err_mask);
1849 do_s2io_write_bits(RTI_SM_ERR_ALARM |
1850 RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
1851 flag, &bar0->rti_err_mask);
1854 if (mask & RX_MAC_INTR) {
1855 gen_int_mask |= RXMAC_INT_M;
1856 do_s2io_write_bits(MAC_INT_STATUS_RMAC_INT, flag,
1857 &bar0->mac_int_mask);
1858 do_s2io_write_bits(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR |
1859 RMAC_UNUSED_INT | RMAC_SINGLE_ECC_ERR |
1860 RMAC_DOUBLE_ECC_ERR |
1861 RMAC_LINK_STATE_CHANGE_INT,
1862 flag, &bar0->mac_rmac_err_mask);
1865 if (mask & RX_XGXS_INTR)
1867 gen_int_mask |= RXXGXS_INT_M;
1868 do_s2io_write_bits(XGXS_INT_STATUS_RXGXS, flag,
1869 &bar0->xgxs_int_mask);
1870 do_s2io_write_bits(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR, flag,
1871 &bar0->xgxs_rxgxs_err_mask);
1874 if (mask & MC_INTR) {
1875 gen_int_mask |= MC_INT_M;
1876 do_s2io_write_bits(MC_INT_MASK_MC_INT, flag, &bar0->mc_int_mask);
1877 do_s2io_write_bits(MC_ERR_REG_SM_ERR | MC_ERR_REG_ECC_ALL_SNG |
1878 MC_ERR_REG_ECC_ALL_DBL | PLL_LOCK_N, flag,
1879 &bar0->mc_err_mask);
1881 nic->general_int_mask = gen_int_mask;
1883 /* Remove this line when alarm interrupts are enabled */
1884 nic->general_int_mask = 0;
1887 * en_dis_able_nic_intrs - Enable or Disable the interrupts
1888 * @nic: device private variable,
1889 * @mask: A mask indicating which Intr block must be modified and,
1890 * @flag: A flag indicating whether to enable or disable the Intrs.
1891 * Description: This function will either disable or enable the interrupts
1892 * depending on the flag argument. The mask argument can be used to
1893 * enable/disable any Intr block.
1894 * Return Value: NONE.
1897 static void en_dis_able_nic_intrs(struct s2io_nic *nic, u16 mask, int flag)
1899 struct XENA_dev_config __iomem *bar0 = nic->bar0;
1900 register u64 temp64 = 0, intr_mask = 0;
1902 intr_mask = nic->general_int_mask;
1904 /* Top level interrupt classification */
1905 /* PIC Interrupts */
1906 if (mask & TX_PIC_INTR) {
1907 /* Enable PIC Intrs in the general intr mask register */
1908 intr_mask |= TXPIC_INT_M;
1909 if (flag == ENABLE_INTRS) {
1911 * If Hercules adapter enable GPIO otherwise
1912 * disable all PCIX, Flash, MDIO, IIC and GPIO
1913 * interrupts for now.
1916 if (s2io_link_fault_indication(nic) ==
1917 LINK_UP_DOWN_INTERRUPT ) {
1918 do_s2io_write_bits(PIC_INT_GPIO, flag,
1919 &bar0->pic_int_mask);
1920 do_s2io_write_bits(GPIO_INT_MASK_LINK_UP, flag,
1921 &bar0->gpio_int_mask);
1923 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
1924 } else if (flag == DISABLE_INTRS) {
1926 * Disable PIC Intrs in the general
1927 * intr mask register
1929 writeq(DISABLE_ALL_INTRS, &bar0->pic_int_mask);
1933 /* Tx traffic interrupts */
1934 if (mask & TX_TRAFFIC_INTR) {
1935 intr_mask |= TXTRAFFIC_INT_M;
1936 if (flag == ENABLE_INTRS) {
1938 * Enable all the Tx side interrupts
1939 * writing 0 Enables all 64 TX interrupt levels
1941 writeq(0x0, &bar0->tx_traffic_mask);
1942 } else if (flag == DISABLE_INTRS) {
1944 * Disable Tx Traffic Intrs in the general intr mask
1947 writeq(DISABLE_ALL_INTRS, &bar0->tx_traffic_mask);
1951 /* Rx traffic interrupts */
1952 if (mask & RX_TRAFFIC_INTR) {
1953 intr_mask |= RXTRAFFIC_INT_M;
1954 if (flag == ENABLE_INTRS) {
1955 /* writing 0 Enables all 8 RX interrupt levels */
1956 writeq(0x0, &bar0->rx_traffic_mask);
1957 } else if (flag == DISABLE_INTRS) {
1959 * Disable Rx Traffic Intrs in the general intr mask
1962 writeq(DISABLE_ALL_INTRS, &bar0->rx_traffic_mask);
1966 temp64 = readq(&bar0->general_int_mask);
1967 if (flag == ENABLE_INTRS)
1968 temp64 &= ~((u64) intr_mask);
1970 temp64 = DISABLE_ALL_INTRS;
1971 writeq(temp64, &bar0->general_int_mask);
1973 nic->general_int_mask = readq(&bar0->general_int_mask);
1977 * verify_pcc_quiescent- Checks for PCC quiescent state
1978 * Return: 1 If PCC is quiescence
1979 * 0 If PCC is not quiescence
1981 static int verify_pcc_quiescent(struct s2io_nic *sp, int flag)
1984 struct XENA_dev_config __iomem *bar0 = sp->bar0;
1985 u64 val64 = readq(&bar0->adapter_status);
1987 herc = (sp->device_type == XFRAME_II_DEVICE);
1989 if (flag == FALSE) {
1990 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
1991 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE))
1994 if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
1998 if ((!herc && (sp->pdev->revision >= 4)) || herc) {
1999 if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
2000 ADAPTER_STATUS_RMAC_PCC_IDLE))
2003 if (((val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) ==
2004 ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE))
2012 * verify_xena_quiescence - Checks whether the H/W is ready
2013 * Description: Returns whether the H/W is ready to go or not. Depending
2014 * on whether adapter enable bit was written or not the comparison
2015 * differs and the calling function passes the input argument flag to
2017 * Return: 1 If xena is quiescence
2018 * 0 If Xena is not quiescence
2021 static int verify_xena_quiescence(struct s2io_nic *sp)
2024 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2025 u64 val64 = readq(&bar0->adapter_status);
2026 mode = s2io_verify_pci_mode(sp);
2028 if (!(val64 & ADAPTER_STATUS_TDMA_READY)) {
2029 DBG_PRINT(ERR_DBG, "%s", "TDMA is not ready!");
2032 if (!(val64 & ADAPTER_STATUS_RDMA_READY)) {
2033 DBG_PRINT(ERR_DBG, "%s", "RDMA is not ready!");
2036 if (!(val64 & ADAPTER_STATUS_PFC_READY)) {
2037 DBG_PRINT(ERR_DBG, "%s", "PFC is not ready!");
2040 if (!(val64 & ADAPTER_STATUS_TMAC_BUF_EMPTY)) {
2041 DBG_PRINT(ERR_DBG, "%s", "TMAC BUF is not empty!");
2044 if (!(val64 & ADAPTER_STATUS_PIC_QUIESCENT)) {
2045 DBG_PRINT(ERR_DBG, "%s", "PIC is not QUIESCENT!");
2048 if (!(val64 & ADAPTER_STATUS_MC_DRAM_READY)) {
2049 DBG_PRINT(ERR_DBG, "%s", "MC_DRAM is not ready!");
2052 if (!(val64 & ADAPTER_STATUS_MC_QUEUES_READY)) {
2053 DBG_PRINT(ERR_DBG, "%s", "MC_QUEUES is not ready!");
2056 if (!(val64 & ADAPTER_STATUS_M_PLL_LOCK)) {
2057 DBG_PRINT(ERR_DBG, "%s", "M_PLL is not locked!");
2062 * In PCI 33 mode, the P_PLL is not used, and therefore,
2063 * the the P_PLL_LOCK bit in the adapter_status register will
2066 if (!(val64 & ADAPTER_STATUS_P_PLL_LOCK) &&
2067 sp->device_type == XFRAME_II_DEVICE && mode !=
2069 DBG_PRINT(ERR_DBG, "%s", "P_PLL is not locked!");
2072 if (!((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
2073 ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
2074 DBG_PRINT(ERR_DBG, "%s", "RC_PRC is not QUIESCENT!");
2081 * fix_mac_address - Fix for Mac addr problem on Alpha platforms
2082 * @sp: Pointer to device specifc structure
2084 * New procedure to clear mac address reading problems on Alpha platforms
2088 static void fix_mac_address(struct s2io_nic * sp)
2090 struct XENA_dev_config __iomem *bar0 = sp->bar0;
2094 while (fix_mac[i] != END_SIGN) {
2095 writeq(fix_mac[i++], &bar0->gpio_control);
2097 val64 = readq(&bar0->gpio_control);
2102 * start_nic - Turns the device on
2103 * @nic : device private variable.
2105 * This function actually turns the device on. Before this function is
2106 * called,all Registers are configured from their reset states
2107 * and shared memory is allocated but the NIC is still quiescent. On
2108 * calling this function, the device interrupts are cleared and the NIC is
2109 * literally switched on by writing into the adapter control register.
2111 * SUCCESS on success and -1 on failure.
2114 static int start_nic(struct s2io_nic *nic)
2116 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2117 struct net_device *dev = nic->dev;
2118 register u64 val64 = 0;
2120 struct mac_info *mac_control;
2121 struct config_param *config;
2123 mac_control = &nic->mac_control;
2124 config = &nic->config;
2126 /* PRC Initialization and configuration */
2127 for (i = 0; i < config->rx_ring_num; i++) {
2128 writeq((u64) mac_control->rings[i].rx_blocks[0].block_dma_addr,
2129 &bar0->prc_rxd0_n[i]);
2131 val64 = readq(&bar0->prc_ctrl_n[i]);
2132 if (nic->rxd_mode == RXD_MODE_1)
2133 val64 |= PRC_CTRL_RC_ENABLED;
2135 val64 |= PRC_CTRL_RC_ENABLED | PRC_CTRL_RING_MODE_3;
2136 if (nic->device_type == XFRAME_II_DEVICE)
2137 val64 |= PRC_CTRL_GROUP_READS;
2138 val64 &= ~PRC_CTRL_RXD_BACKOFF_INTERVAL(0xFFFFFF);
2139 val64 |= PRC_CTRL_RXD_BACKOFF_INTERVAL(0x1000);
2140 writeq(val64, &bar0->prc_ctrl_n[i]);
2143 if (nic->rxd_mode == RXD_MODE_3B) {
2144 /* Enabling 2 buffer mode by writing into Rx_pa_cfg reg. */
2145 val64 = readq(&bar0->rx_pa_cfg);
2146 val64 |= RX_PA_CFG_IGNORE_L2_ERR;
2147 writeq(val64, &bar0->rx_pa_cfg);
2150 if (vlan_tag_strip == 0) {
2151 val64 = readq(&bar0->rx_pa_cfg);
2152 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
2153 writeq(val64, &bar0->rx_pa_cfg);
2154 vlan_strip_flag = 0;
2158 * Enabling MC-RLDRAM. After enabling the device, we timeout
2159 * for around 100ms, which is approximately the time required
2160 * for the device to be ready for operation.
2162 val64 = readq(&bar0->mc_rldram_mrs);
2163 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE | MC_RLDRAM_MRS_ENABLE;
2164 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
2165 val64 = readq(&bar0->mc_rldram_mrs);
2167 msleep(100); /* Delay by around 100 ms. */
2169 /* Enabling ECC Protection. */
2170 val64 = readq(&bar0->adapter_control);
2171 val64 &= ~ADAPTER_ECC_EN;
2172 writeq(val64, &bar0->adapter_control);
2175 * Verify if the device is ready to be enabled, if so enable
2178 val64 = readq(&bar0->adapter_status);
2179 if (!verify_xena_quiescence(nic)) {
2180 DBG_PRINT(ERR_DBG, "%s: device is not ready, ", dev->name);
2181 DBG_PRINT(ERR_DBG, "Adapter status reads: 0x%llx\n",
2182 (unsigned long long) val64);
2187 * With some switches, link might be already up at this point.
2188 * Because of this weird behavior, when we enable laser,
2189 * we may not get link. We need to handle this. We cannot
2190 * figure out which switch is misbehaving. So we are forced to
2191 * make a global change.
2194 /* Enabling Laser. */
2195 val64 = readq(&bar0->adapter_control);
2196 val64 |= ADAPTER_EOI_TX_ON;
2197 writeq(val64, &bar0->adapter_control);
2199 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
2201 * Dont see link state interrupts initally on some switches,
2202 * so directly scheduling the link state task here.
2204 schedule_work(&nic->set_link_task);
2206 /* SXE-002: Initialize link and activity LED */
2207 subid = nic->pdev->subsystem_device;
2208 if (((subid & 0xFF) >= 0x07) &&
2209 (nic->device_type == XFRAME_I_DEVICE)) {
2210 val64 = readq(&bar0->gpio_control);
2211 val64 |= 0x0000800000000000ULL;
2212 writeq(val64, &bar0->gpio_control);
2213 val64 = 0x0411040400000000ULL;
2214 writeq(val64, (void __iomem *)bar0 + 0x2700);
2220 * s2io_txdl_getskb - Get the skb from txdl, unmap and return skb
2222 static struct sk_buff *s2io_txdl_getskb(struct fifo_info *fifo_data, struct \
2223 TxD *txdlp, int get_off)
2225 struct s2io_nic *nic = fifo_data->nic;
2226 struct sk_buff *skb;
2231 if (txds->Host_Control == (u64)(long)nic->ufo_in_band_v) {
2232 pci_unmap_single(nic->pdev, (dma_addr_t)
2233 txds->Buffer_Pointer, sizeof(u64),
2238 skb = (struct sk_buff *) ((unsigned long)
2239 txds->Host_Control);
2241 memset(txdlp, 0, (sizeof(struct TxD) * fifo_data->max_txds));
2244 pci_unmap_single(nic->pdev, (dma_addr_t)
2245 txds->Buffer_Pointer,
2246 skb->len - skb->data_len,
2248 frg_cnt = skb_shinfo(skb)->nr_frags;
2251 for (j = 0; j < frg_cnt; j++, txds++) {
2252 skb_frag_t *frag = &skb_shinfo(skb)->frags[j];
2253 if (!txds->Buffer_Pointer)
2255 pci_unmap_page(nic->pdev, (dma_addr_t)
2256 txds->Buffer_Pointer,
2257 frag->size, PCI_DMA_TODEVICE);
2260 memset(txdlp,0, (sizeof(struct TxD) * fifo_data->max_txds));
2265 * free_tx_buffers - Free all queued Tx buffers
2266 * @nic : device private variable.
2268 * Free all queued Tx buffers.
2269 * Return Value: void
2272 static void free_tx_buffers(struct s2io_nic *nic)
2274 struct net_device *dev = nic->dev;
2275 struct sk_buff *skb;
2278 struct mac_info *mac_control;
2279 struct config_param *config;
2282 mac_control = &nic->mac_control;
2283 config = &nic->config;
2285 for (i = 0; i < config->tx_fifo_num; i++) {
2286 for (j = 0; j < config->tx_cfg[i].fifo_len - 1; j++) {
2287 txdp = (struct TxD *) \
2288 mac_control->fifos[i].list_info[j].list_virt_addr;
2289 skb = s2io_txdl_getskb(&mac_control->fifos[i], txdp, j);
2291 nic->mac_control.stats_info->sw_stat.mem_freed
2298 "%s:forcibly freeing %d skbs on FIFO%d\n",
2300 mac_control->fifos[i].tx_curr_get_info.offset = 0;
2301 mac_control->fifos[i].tx_curr_put_info.offset = 0;
2306 * stop_nic - To stop the nic
2307 * @nic ; device private variable.
2309 * This function does exactly the opposite of what the start_nic()
2310 * function does. This function is called to stop the device.
2315 static void stop_nic(struct s2io_nic *nic)
2317 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2318 register u64 val64 = 0;
2320 struct mac_info *mac_control;
2321 struct config_param *config;
2323 mac_control = &nic->mac_control;
2324 config = &nic->config;
2326 /* Disable all interrupts */
2327 en_dis_err_alarms(nic, ENA_ALL_INTRS, DISABLE_INTRS);
2328 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
2329 interruptible |= TX_PIC_INTR;
2330 en_dis_able_nic_intrs(nic, interruptible, DISABLE_INTRS);
2332 /* Clearing Adapter_En bit of ADAPTER_CONTROL Register */
2333 val64 = readq(&bar0->adapter_control);
2334 val64 &= ~(ADAPTER_CNTL_EN);
2335 writeq(val64, &bar0->adapter_control);
2339 * fill_rx_buffers - Allocates the Rx side skbs
2340 * @nic: device private variable
2341 * @ring_no: ring number
2343 * The function allocates Rx side skbs and puts the physical
2344 * address of these buffers into the RxD buffer pointers, so that the NIC
2345 * can DMA the received frame into these locations.
2346 * The NIC supports 3 receive modes, viz
2348 * 2. three buffer and
2349 * 3. Five buffer modes.
2350 * Each mode defines how many fragments the received frame will be split
2351 * up into by the NIC. The frame is split into L3 header, L4 Header,
2352 * L4 payload in three buffer mode and in 5 buffer mode, L4 payload itself
2353 * is split into 3 fragments. As of now only single buffer mode is
2356 * SUCCESS on success or an appropriate -ve value on failure.
2359 static int fill_rx_buffers(struct s2io_nic *nic, int ring_no)
2361 struct net_device *dev = nic->dev;
2362 struct sk_buff *skb;
2364 int off, off1, size, block_no, block_no1;
2367 struct mac_info *mac_control;
2368 struct config_param *config;
2371 unsigned long flags;
2372 struct RxD_t *first_rxdp = NULL;
2373 u64 Buffer0_ptr = 0, Buffer1_ptr = 0;
2376 struct swStat *stats = &nic->mac_control.stats_info->sw_stat;
2378 mac_control = &nic->mac_control;
2379 config = &nic->config;
2380 alloc_cnt = mac_control->rings[ring_no].pkt_cnt -
2381 atomic_read(&nic->rx_bufs_left[ring_no]);
2383 block_no1 = mac_control->rings[ring_no].rx_curr_get_info.block_index;
2384 off1 = mac_control->rings[ring_no].rx_curr_get_info.offset;
2385 while (alloc_tab < alloc_cnt) {
2386 block_no = mac_control->rings[ring_no].rx_curr_put_info.
2388 off = mac_control->rings[ring_no].rx_curr_put_info.offset;
2390 rxdp = mac_control->rings[ring_no].
2391 rx_blocks[block_no].rxds[off].virt_addr;
2393 if ((block_no == block_no1) && (off == off1) &&
2394 (rxdp->Host_Control)) {
2395 DBG_PRINT(INTR_DBG, "%s: Get and Put",
2397 DBG_PRINT(INTR_DBG, " info equated\n");
2400 if (off && (off == rxd_count[nic->rxd_mode])) {
2401 mac_control->rings[ring_no].rx_curr_put_info.
2403 if (mac_control->rings[ring_no].rx_curr_put_info.
2404 block_index == mac_control->rings[ring_no].
2406 mac_control->rings[ring_no].rx_curr_put_info.
2408 block_no = mac_control->rings[ring_no].
2409 rx_curr_put_info.block_index;
2410 if (off == rxd_count[nic->rxd_mode])
2412 mac_control->rings[ring_no].rx_curr_put_info.
2414 rxdp = mac_control->rings[ring_no].
2415 rx_blocks[block_no].block_virt_addr;
2416 DBG_PRINT(INTR_DBG, "%s: Next block at: %p\n",
2420 spin_lock_irqsave(&nic->put_lock, flags);
2421 mac_control->rings[ring_no].put_pos =
2422 (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
2423 spin_unlock_irqrestore(&nic->put_lock, flags);
2425 mac_control->rings[ring_no].put_pos =
2426 (block_no * (rxd_count[nic->rxd_mode] + 1)) + off;
2428 if ((rxdp->Control_1 & RXD_OWN_XENA) &&
2429 ((nic->rxd_mode == RXD_MODE_3B) &&
2430 (rxdp->Control_2 & s2BIT(0)))) {
2431 mac_control->rings[ring_no].rx_curr_put_info.
2435 /* calculate size of skb based on ring mode */
2436 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
2437 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
2438 if (nic->rxd_mode == RXD_MODE_1)
2439 size += NET_IP_ALIGN;
2441 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
2444 skb = dev_alloc_skb(size);
2446 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
2447 DBG_PRINT(INFO_DBG, "memory to allocate SKBs\n");
2450 first_rxdp->Control_1 |= RXD_OWN_XENA;
2452 nic->mac_control.stats_info->sw_stat. \
2453 mem_alloc_fail_cnt++;
2456 nic->mac_control.stats_info->sw_stat.mem_allocated
2458 if (nic->rxd_mode == RXD_MODE_1) {
2459 /* 1 buffer mode - normal operation mode */
2460 rxdp1 = (struct RxD1*)rxdp;
2461 memset(rxdp, 0, sizeof(struct RxD1));
2462 skb_reserve(skb, NET_IP_ALIGN);
2463 rxdp1->Buffer0_ptr = pci_map_single
2464 (nic->pdev, skb->data, size - NET_IP_ALIGN,
2465 PCI_DMA_FROMDEVICE);
2466 if( (rxdp1->Buffer0_ptr == 0) ||
2467 (rxdp1->Buffer0_ptr ==
2469 goto pci_map_failed;
2472 SET_BUFFER0_SIZE_1(size - NET_IP_ALIGN);
2474 } else if (nic->rxd_mode == RXD_MODE_3B) {
2477 * 2 buffer mode provides 128
2478 * byte aligned receive buffers.
2481 rxdp3 = (struct RxD3*)rxdp;
2482 /* save buffer pointers to avoid frequent dma mapping */
2483 Buffer0_ptr = rxdp3->Buffer0_ptr;
2484 Buffer1_ptr = rxdp3->Buffer1_ptr;
2485 memset(rxdp, 0, sizeof(struct RxD3));
2486 /* restore the buffer pointers for dma sync*/
2487 rxdp3->Buffer0_ptr = Buffer0_ptr;
2488 rxdp3->Buffer1_ptr = Buffer1_ptr;
2490 ba = &mac_control->rings[ring_no].ba[block_no][off];
2491 skb_reserve(skb, BUF0_LEN);
2492 tmp = (u64)(unsigned long) skb->data;
2495 skb->data = (void *) (unsigned long)tmp;
2496 skb_reset_tail_pointer(skb);
2498 if (!(rxdp3->Buffer0_ptr))
2499 rxdp3->Buffer0_ptr =
2500 pci_map_single(nic->pdev, ba->ba_0, BUF0_LEN,
2501 PCI_DMA_FROMDEVICE);
2503 pci_dma_sync_single_for_device(nic->pdev,
2504 (dma_addr_t) rxdp3->Buffer0_ptr,
2505 BUF0_LEN, PCI_DMA_FROMDEVICE);
2506 if( (rxdp3->Buffer0_ptr == 0) ||
2507 (rxdp3->Buffer0_ptr == DMA_ERROR_CODE))
2508 goto pci_map_failed;
2510 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
2511 if (nic->rxd_mode == RXD_MODE_3B) {
2512 /* Two buffer mode */
2515 * Buffer2 will have L3/L4 header plus
2518 rxdp3->Buffer2_ptr = pci_map_single
2519 (nic->pdev, skb->data, dev->mtu + 4,
2520 PCI_DMA_FROMDEVICE);
2522 if( (rxdp3->Buffer2_ptr == 0) ||
2523 (rxdp3->Buffer2_ptr == DMA_ERROR_CODE))
2524 goto pci_map_failed;
2526 rxdp3->Buffer1_ptr =
2527 pci_map_single(nic->pdev,
2529 PCI_DMA_FROMDEVICE);
2530 if( (rxdp3->Buffer1_ptr == 0) ||
2531 (rxdp3->Buffer1_ptr == DMA_ERROR_CODE)) {
2534 (dma_addr_t)rxdp3->Buffer2_ptr,
2536 PCI_DMA_FROMDEVICE);
2537 goto pci_map_failed;
2539 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
2540 rxdp->Control_2 |= SET_BUFFER2_SIZE_3
2543 rxdp->Control_2 |= s2BIT(0);
2545 rxdp->Host_Control = (unsigned long) (skb);
2546 if (alloc_tab & ((1 << rxsync_frequency) - 1))
2547 rxdp->Control_1 |= RXD_OWN_XENA;
2549 if (off == (rxd_count[nic->rxd_mode] + 1))
2551 mac_control->rings[ring_no].rx_curr_put_info.offset = off;
2553 rxdp->Control_2 |= SET_RXD_MARKER;
2554 if (!(alloc_tab & ((1 << rxsync_frequency) - 1))) {
2557 first_rxdp->Control_1 |= RXD_OWN_XENA;
2561 atomic_inc(&nic->rx_bufs_left[ring_no]);
2566 /* Transfer ownership of first descriptor to adapter just before
2567 * exiting. Before that, use memory barrier so that ownership
2568 * and other fields are seen by adapter correctly.
2572 first_rxdp->Control_1 |= RXD_OWN_XENA;
2577 stats->pci_map_fail_cnt++;
2578 stats->mem_freed += skb->truesize;
2579 dev_kfree_skb_irq(skb);
2583 static void free_rxd_blk(struct s2io_nic *sp, int ring_no, int blk)
2585 struct net_device *dev = sp->dev;
2587 struct sk_buff *skb;
2589 struct mac_info *mac_control;
2594 mac_control = &sp->mac_control;
2595 for (j = 0 ; j < rxd_count[sp->rxd_mode]; j++) {
2596 rxdp = mac_control->rings[ring_no].
2597 rx_blocks[blk].rxds[j].virt_addr;
2598 skb = (struct sk_buff *)
2599 ((unsigned long) rxdp->Host_Control);
2603 if (sp->rxd_mode == RXD_MODE_1) {
2604 rxdp1 = (struct RxD1*)rxdp;
2605 pci_unmap_single(sp->pdev, (dma_addr_t)
2608 HEADER_ETHERNET_II_802_3_SIZE
2609 + HEADER_802_2_SIZE +
2611 PCI_DMA_FROMDEVICE);
2612 memset(rxdp, 0, sizeof(struct RxD1));
2613 } else if(sp->rxd_mode == RXD_MODE_3B) {
2614 rxdp3 = (struct RxD3*)rxdp;
2615 ba = &mac_control->rings[ring_no].
2617 pci_unmap_single(sp->pdev, (dma_addr_t)
2620 PCI_DMA_FROMDEVICE);
2621 pci_unmap_single(sp->pdev, (dma_addr_t)
2624 PCI_DMA_FROMDEVICE);
2625 pci_unmap_single(sp->pdev, (dma_addr_t)
2628 PCI_DMA_FROMDEVICE);
2629 memset(rxdp, 0, sizeof(struct RxD3));
2631 sp->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
2633 atomic_dec(&sp->rx_bufs_left[ring_no]);
2638 * free_rx_buffers - Frees all Rx buffers
2639 * @sp: device private variable.
2641 * This function will free all Rx buffers allocated by host.
2646 static void free_rx_buffers(struct s2io_nic *sp)
2648 struct net_device *dev = sp->dev;
2649 int i, blk = 0, buf_cnt = 0;
2650 struct mac_info *mac_control;
2651 struct config_param *config;
2653 mac_control = &sp->mac_control;
2654 config = &sp->config;
2656 for (i = 0; i < config->rx_ring_num; i++) {
2657 for (blk = 0; blk < rx_ring_sz[i]; blk++)
2658 free_rxd_blk(sp,i,blk);
2660 mac_control->rings[i].rx_curr_put_info.block_index = 0;
2661 mac_control->rings[i].rx_curr_get_info.block_index = 0;
2662 mac_control->rings[i].rx_curr_put_info.offset = 0;
2663 mac_control->rings[i].rx_curr_get_info.offset = 0;
2664 atomic_set(&sp->rx_bufs_left[i], 0);
2665 DBG_PRINT(INIT_DBG, "%s:Freed 0x%x Rx Buffers on ring%d\n",
2666 dev->name, buf_cnt, i);
2671 * s2io_poll - Rx interrupt handler for NAPI support
2672 * @napi : pointer to the napi structure.
2673 * @budget : The number of packets that were budgeted to be processed
2674 * during one pass through the 'Poll" function.
2676 * Comes into picture only if NAPI support has been incorporated. It does
2677 * the same thing that rx_intr_handler does, but not in a interrupt context
2678 * also It will process only a given number of packets.
2680 * 0 on success and 1 if there are No Rx packets to be processed.
2683 static int s2io_poll(struct napi_struct *napi, int budget)
2685 struct s2io_nic *nic = container_of(napi, struct s2io_nic, napi);
2686 struct net_device *dev = nic->dev;
2687 int pkt_cnt = 0, org_pkts_to_process;
2688 struct mac_info *mac_control;
2689 struct config_param *config;
2690 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2693 if (!is_s2io_card_up(nic))
2696 mac_control = &nic->mac_control;
2697 config = &nic->config;
2699 nic->pkts_to_process = budget;
2700 org_pkts_to_process = nic->pkts_to_process;
2702 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
2703 readl(&bar0->rx_traffic_int);
2705 for (i = 0; i < config->rx_ring_num; i++) {
2706 rx_intr_handler(&mac_control->rings[i]);
2707 pkt_cnt = org_pkts_to_process - nic->pkts_to_process;
2708 if (!nic->pkts_to_process) {
2709 /* Quota for the current iteration has been met */
2714 netif_rx_complete(dev, napi);
2716 for (i = 0; i < config->rx_ring_num; i++) {
2717 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2718 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2719 DBG_PRINT(INFO_DBG, " in Rx Poll!!\n");
2723 /* Re enable the Rx interrupts. */
2724 writeq(0x0, &bar0->rx_traffic_mask);
2725 readl(&bar0->rx_traffic_mask);
2729 for (i = 0; i < config->rx_ring_num; i++) {
2730 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2731 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2732 DBG_PRINT(INFO_DBG, " in Rx Poll!!\n");
2739 #ifdef CONFIG_NET_POLL_CONTROLLER
2741 * s2io_netpoll - netpoll event handler entry point
2742 * @dev : pointer to the device structure.
2744 * This function will be called by upper layer to check for events on the
2745 * interface in situations where interrupts are disabled. It is used for
2746 * specific in-kernel networking tasks, such as remote consoles and kernel
2747 * debugging over the network (example netdump in RedHat).
2749 static void s2io_netpoll(struct net_device *dev)
2751 struct s2io_nic *nic = dev->priv;
2752 struct mac_info *mac_control;
2753 struct config_param *config;
2754 struct XENA_dev_config __iomem *bar0 = nic->bar0;
2755 u64 val64 = 0xFFFFFFFFFFFFFFFFULL;
2758 if (pci_channel_offline(nic->pdev))
2761 disable_irq(dev->irq);
2763 mac_control = &nic->mac_control;
2764 config = &nic->config;
2766 writeq(val64, &bar0->rx_traffic_int);
2767 writeq(val64, &bar0->tx_traffic_int);
2769 /* we need to free up the transmitted skbufs or else netpoll will
2770 * run out of skbs and will fail and eventually netpoll application such
2771 * as netdump will fail.
2773 for (i = 0; i < config->tx_fifo_num; i++)
2774 tx_intr_handler(&mac_control->fifos[i]);
2776 /* check for received packet and indicate up to network */
2777 for (i = 0; i < config->rx_ring_num; i++)
2778 rx_intr_handler(&mac_control->rings[i]);
2780 for (i = 0; i < config->rx_ring_num; i++) {
2781 if (fill_rx_buffers(nic, i) == -ENOMEM) {
2782 DBG_PRINT(INFO_DBG, "%s:Out of memory", dev->name);
2783 DBG_PRINT(INFO_DBG, " in Rx Netpoll!!\n");
2787 enable_irq(dev->irq);
2793 * rx_intr_handler - Rx interrupt handler
2794 * @nic: device private variable.
2796 * If the interrupt is because of a received frame or if the
2797 * receive ring contains fresh as yet un-processed frames,this function is
2798 * called. It picks out the RxD at which place the last Rx processing had
2799 * stopped and sends the skb to the OSM's Rx handler and then increments
2804 static void rx_intr_handler(struct ring_info *ring_data)
2806 struct s2io_nic *nic = ring_data->nic;
2807 struct net_device *dev = (struct net_device *) nic->dev;
2808 int get_block, put_block, put_offset;
2809 struct rx_curr_get_info get_info, put_info;
2811 struct sk_buff *skb;
2817 spin_lock(&nic->rx_lock);
2819 get_info = ring_data->rx_curr_get_info;
2820 get_block = get_info.block_index;
2821 memcpy(&put_info, &ring_data->rx_curr_put_info, sizeof(put_info));
2822 put_block = put_info.block_index;
2823 rxdp = ring_data->rx_blocks[get_block].rxds[get_info.offset].virt_addr;
2825 spin_lock(&nic->put_lock);
2826 put_offset = ring_data->put_pos;
2827 spin_unlock(&nic->put_lock);
2829 put_offset = ring_data->put_pos;
2831 while (RXD_IS_UP2DT(rxdp)) {
2833 * If your are next to put index then it's
2834 * FIFO full condition
2836 if ((get_block == put_block) &&
2837 (get_info.offset + 1) == put_info.offset) {
2838 DBG_PRINT(INTR_DBG, "%s: Ring Full\n",dev->name);
2841 skb = (struct sk_buff *) ((unsigned long)rxdp->Host_Control);
2843 DBG_PRINT(ERR_DBG, "%s: The skb is ",
2845 DBG_PRINT(ERR_DBG, "Null in Rx Intr\n");
2846 spin_unlock(&nic->rx_lock);
2849 if (nic->rxd_mode == RXD_MODE_1) {
2850 rxdp1 = (struct RxD1*)rxdp;
2851 pci_unmap_single(nic->pdev, (dma_addr_t)
2854 HEADER_ETHERNET_II_802_3_SIZE +
2857 PCI_DMA_FROMDEVICE);
2858 } else if (nic->rxd_mode == RXD_MODE_3B) {
2859 rxdp3 = (struct RxD3*)rxdp;
2860 pci_dma_sync_single_for_cpu(nic->pdev, (dma_addr_t)
2862 BUF0_LEN, PCI_DMA_FROMDEVICE);
2863 pci_unmap_single(nic->pdev, (dma_addr_t)
2866 PCI_DMA_FROMDEVICE);
2868 prefetch(skb->data);
2869 rx_osm_handler(ring_data, rxdp);
2871 ring_data->rx_curr_get_info.offset = get_info.offset;
2872 rxdp = ring_data->rx_blocks[get_block].
2873 rxds[get_info.offset].virt_addr;
2874 if (get_info.offset == rxd_count[nic->rxd_mode]) {
2875 get_info.offset = 0;
2876 ring_data->rx_curr_get_info.offset = get_info.offset;
2878 if (get_block == ring_data->block_count)
2880 ring_data->rx_curr_get_info.block_index = get_block;
2881 rxdp = ring_data->rx_blocks[get_block].block_virt_addr;
2884 nic->pkts_to_process -= 1;
2885 if ((napi) && (!nic->pkts_to_process))
2888 if ((indicate_max_pkts) && (pkt_cnt > indicate_max_pkts))
2892 /* Clear all LRO sessions before exiting */
2893 for (i=0; i<MAX_LRO_SESSIONS; i++) {
2894 struct lro *lro = &nic->lro0_n[i];
2896 update_L3L4_header(nic, lro);
2897 queue_rx_frame(lro->parent);
2898 clear_lro_session(lro);
2903 spin_unlock(&nic->rx_lock);
2907 * tx_intr_handler - Transmit interrupt handler
2908 * @nic : device private variable
2910 * If an interrupt was raised to indicate DMA complete of the
2911 * Tx packet, this function is called. It identifies the last TxD
2912 * whose buffer was freed and frees all skbs whose data have already
2913 * DMA'ed into the NICs internal memory.
2918 static void tx_intr_handler(struct fifo_info *fifo_data)
2920 struct s2io_nic *nic = fifo_data->nic;
2921 struct net_device *dev = (struct net_device *) nic->dev;
2922 struct tx_curr_get_info get_info, put_info;
2923 struct sk_buff *skb;
2927 get_info = fifo_data->tx_curr_get_info;
2928 memcpy(&put_info, &fifo_data->tx_curr_put_info, sizeof(put_info));
2929 txdlp = (struct TxD *) fifo_data->list_info[get_info.offset].
2931 while ((!(txdlp->Control_1 & TXD_LIST_OWN_XENA)) &&
2932 (get_info.offset != put_info.offset) &&
2933 (txdlp->Host_Control)) {
2934 /* Check for TxD errors */
2935 if (txdlp->Control_1 & TXD_T_CODE) {
2936 unsigned long long err;
2937 err = txdlp->Control_1 & TXD_T_CODE;
2939 nic->mac_control.stats_info->sw_stat.
2943 /* update t_code statistics */
2944 err_mask = err >> 48;
2947 nic->mac_control.stats_info->sw_stat.
2952 nic->mac_control.stats_info->sw_stat.
2953 tx_desc_abort_cnt++;
2957 nic->mac_control.stats_info->sw_stat.
2958 tx_parity_err_cnt++;
2962 nic->mac_control.stats_info->sw_stat.
2967 nic->mac_control.stats_info->sw_stat.
2968 tx_list_proc_err_cnt++;
2973 skb = s2io_txdl_getskb(fifo_data, txdlp, get_info.offset);
2975 DBG_PRINT(ERR_DBG, "%s: Null skb ",
2977 DBG_PRINT(ERR_DBG, "in Tx Free Intr\n");
2981 /* Updating the statistics block */
2982 nic->stats.tx_bytes += skb->len;
2983 nic->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
2984 dev_kfree_skb_irq(skb);
2987 if (get_info.offset == get_info.fifo_len + 1)
2988 get_info.offset = 0;
2989 txdlp = (struct TxD *) fifo_data->list_info
2990 [get_info.offset].list_virt_addr;
2991 fifo_data->tx_curr_get_info.offset =
2995 spin_lock(&nic->tx_lock);
2996 if (netif_queue_stopped(dev))
2997 netif_wake_queue(dev);
2998 spin_unlock(&nic->tx_lock);
3002 * s2io_mdio_write - Function to write in to MDIO registers
3003 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3004 * @addr : address value
3005 * @value : data value
3006 * @dev : pointer to net_device structure
3008 * This function is used to write values to the MDIO registers
3011 static void s2io_mdio_write(u32 mmd_type, u64 addr, u16 value, struct net_device *dev)
3014 struct s2io_nic *sp = dev->priv;
3015 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3017 //address transaction
3018 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3019 | MDIO_MMD_DEV_ADDR(mmd_type)
3020 | MDIO_MMS_PRT_ADDR(0x0);
3021 writeq(val64, &bar0->mdio_control);
3022 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3023 writeq(val64, &bar0->mdio_control);
3028 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3029 | MDIO_MMD_DEV_ADDR(mmd_type)
3030 | MDIO_MMS_PRT_ADDR(0x0)
3031 | MDIO_MDIO_DATA(value)
3032 | MDIO_OP(MDIO_OP_WRITE_TRANS);
3033 writeq(val64, &bar0->mdio_control);
3034 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3035 writeq(val64, &bar0->mdio_control);
3039 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3040 | MDIO_MMD_DEV_ADDR(mmd_type)
3041 | MDIO_MMS_PRT_ADDR(0x0)
3042 | MDIO_OP(MDIO_OP_READ_TRANS);
3043 writeq(val64, &bar0->mdio_control);
3044 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3045 writeq(val64, &bar0->mdio_control);
3051 * s2io_mdio_read - Function to write in to MDIO registers
3052 * @mmd_type : MMD type value (PMA/PMD/WIS/PCS/PHYXS)
3053 * @addr : address value
3054 * @dev : pointer to net_device structure
3056 * This function is used to read values to the MDIO registers
3059 static u64 s2io_mdio_read(u32 mmd_type, u64 addr, struct net_device *dev)
3063 struct s2io_nic *sp = dev->priv;
3064 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3066 /* address transaction */
3067 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3068 | MDIO_MMD_DEV_ADDR(mmd_type)
3069 | MDIO_MMS_PRT_ADDR(0x0);
3070 writeq(val64, &bar0->mdio_control);
3071 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3072 writeq(val64, &bar0->mdio_control);
3075 /* Data transaction */
3077 val64 = val64 | MDIO_MMD_INDX_ADDR(addr)
3078 | MDIO_MMD_DEV_ADDR(mmd_type)
3079 | MDIO_MMS_PRT_ADDR(0x0)
3080 | MDIO_OP(MDIO_OP_READ_TRANS);
3081 writeq(val64, &bar0->mdio_control);
3082 val64 = val64 | MDIO_CTRL_START_TRANS(0xE);
3083 writeq(val64, &bar0->mdio_control);
3086 /* Read the value from regs */
3087 rval64 = readq(&bar0->mdio_control);
3088 rval64 = rval64 & 0xFFFF0000;
3089 rval64 = rval64 >> 16;
3093 * s2io_chk_xpak_counter - Function to check the status of the xpak counters
3094 * @counter : couter value to be updated
3095 * @flag : flag to indicate the status
3096 * @type : counter type
3098 * This function is to check the status of the xpak counters value
3102 static void s2io_chk_xpak_counter(u64 *counter, u64 * regs_stat, u32 index, u16 flag, u16 type)
3107 for(i = 0; i <index; i++)
3112 *counter = *counter + 1;
3113 val64 = *regs_stat & mask;
3114 val64 = val64 >> (index * 0x2);
3121 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3122 "service. Excessive temperatures may "
3123 "result in premature transceiver "
3127 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3128 "service Excessive bias currents may "
3129 "indicate imminent laser diode "
3133 DBG_PRINT(ERR_DBG, "Take Xframe NIC out of "
3134 "service Excessive laser output "
3135 "power may saturate far-end "
3139 DBG_PRINT(ERR_DBG, "Incorrect XPAK Alarm "
3144 val64 = val64 << (index * 0x2);
3145 *regs_stat = (*regs_stat & (~mask)) | (val64);
3148 *regs_stat = *regs_stat & (~mask);
3153 * s2io_updt_xpak_counter - Function to update the xpak counters
3154 * @dev : pointer to net_device struct
3156 * This function is to upate the status of the xpak counters value
3159 static void s2io_updt_xpak_counter(struct net_device *dev)
3167 struct s2io_nic *sp = dev->priv;
3168 struct stat_block *stat_info = sp->mac_control.stats_info;
3170 /* Check the communication with the MDIO slave */
3173 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3174 if((val64 == 0xFFFF) || (val64 == 0x0000))
3176 DBG_PRINT(ERR_DBG, "ERR: MDIO slave access failed - "
3177 "Returned %llx\n", (unsigned long long)val64);
3181 /* Check for the expecte value of 2040 at PMA address 0x0000 */
3184 DBG_PRINT(ERR_DBG, "Incorrect value at PMA address 0x0000 - ");
3185 DBG_PRINT(ERR_DBG, "Returned: %llx- Expected: 0x2040\n",
3186 (unsigned long long)val64);
3190 /* Loading the DOM register to MDIO register */
3192 s2io_mdio_write(MDIO_MMD_PMA_DEV_ADDR, addr, val16, dev);
3193 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3195 /* Reading the Alarm flags */
3198 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3200 flag = CHECKBIT(val64, 0x7);
3202 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_transceiver_temp_high,
3203 &stat_info->xpak_stat.xpak_regs_stat,
3206 if(CHECKBIT(val64, 0x6))
3207 stat_info->xpak_stat.alarm_transceiver_temp_low++;
3209 flag = CHECKBIT(val64, 0x3);
3211 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_laser_bias_current_high,
3212 &stat_info->xpak_stat.xpak_regs_stat,
3215 if(CHECKBIT(val64, 0x2))
3216 stat_info->xpak_stat.alarm_laser_bias_current_low++;
3218 flag = CHECKBIT(val64, 0x1);
3220 s2io_chk_xpak_counter(&stat_info->xpak_stat.alarm_laser_output_power_high,
3221 &stat_info->xpak_stat.xpak_regs_stat,
3224 if(CHECKBIT(val64, 0x0))
3225 stat_info->xpak_stat.alarm_laser_output_power_low++;
3227 /* Reading the Warning flags */
3230 val64 = s2io_mdio_read(MDIO_MMD_PMA_DEV_ADDR, addr, dev);
3232 if(CHECKBIT(val64, 0x7))
3233 stat_info->xpak_stat.warn_transceiver_temp_high++;
3235 if(CHECKBIT(val64, 0x6))
3236 stat_info->xpak_stat.warn_transceiver_temp_low++;
3238 if(CHECKBIT(val64, 0x3))
3239 stat_info->xpak_stat.warn_laser_bias_current_high++;
3241 if(CHECKBIT(val64, 0x2))
3242 stat_info->xpak_stat.warn_laser_bias_current_low++;
3244 if(CHECKBIT(val64, 0x1))
3245 stat_info->xpak_stat.warn_laser_output_power_high++;
3247 if(CHECKBIT(val64, 0x0))
3248 stat_info->xpak_stat.warn_laser_output_power_low++;
3252 * wait_for_cmd_complete - waits for a command to complete.
3253 * @sp : private member of the device structure, which is a pointer to the
3254 * s2io_nic structure.
3255 * Description: Function that waits for a command to Write into RMAC
3256 * ADDR DATA registers to be completed and returns either success or
3257 * error depending on whether the command was complete or not.
3259 * SUCCESS on success and FAILURE on failure.
3262 static int wait_for_cmd_complete(void __iomem *addr, u64 busy_bit,
3265 int ret = FAILURE, cnt = 0, delay = 1;
3268 if ((bit_state != S2IO_BIT_RESET) && (bit_state != S2IO_BIT_SET))
3272 val64 = readq(addr);
3273 if (bit_state == S2IO_BIT_RESET) {
3274 if (!(val64 & busy_bit)) {
3279 if (!(val64 & busy_bit)) {
3296 * check_pci_device_id - Checks if the device id is supported
3298 * Description: Function to check if the pci device id is supported by driver.
3299 * Return value: Actual device id if supported else PCI_ANY_ID
3301 static u16 check_pci_device_id(u16 id)
3304 case PCI_DEVICE_ID_HERC_WIN:
3305 case PCI_DEVICE_ID_HERC_UNI:
3306 return XFRAME_II_DEVICE;
3307 case PCI_DEVICE_ID_S2IO_UNI:
3308 case PCI_DEVICE_ID_S2IO_WIN:
3309 return XFRAME_I_DEVICE;
3316 * s2io_reset - Resets the card.
3317 * @sp : private member of the device structure.
3318 * Description: Function to Reset the card. This function then also
3319 * restores the previously saved PCI configuration space registers as
3320 * the card reset also resets the configuration space.
3325 static void s2io_reset(struct s2io_nic * sp)
3327 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3332 unsigned long long up_cnt, down_cnt, up_time, down_time, reset_cnt;
3333 unsigned long long mem_alloc_cnt, mem_free_cnt, watchdog_cnt;
3335 DBG_PRINT(INIT_DBG,"%s - Resetting XFrame card %s\n",
3336 __FUNCTION__, sp->dev->name);
3338 /* Back up the PCI-X CMD reg, dont want to lose MMRBC, OST settings */
3339 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER, &(pci_cmd));
3341 val64 = SW_RESET_ALL;
3342 writeq(val64, &bar0->sw_reset);
3343 if (strstr(sp->product_name, "CX4")) {
3347 for (i = 0; i < S2IO_MAX_PCI_CONFIG_SPACE_REINIT; i++) {
3349 /* Restore the PCI state saved during initialization. */
3350 pci_restore_state(sp->pdev);
3351 pci_read_config_word(sp->pdev, 0x2, &val16);
3352 if (check_pci_device_id(val16) != (u16)PCI_ANY_ID)
3357 if (check_pci_device_id(val16) == (u16)PCI_ANY_ID) {
3358 DBG_PRINT(ERR_DBG,"%s SW_Reset failed!\n", __FUNCTION__);
3361 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER, pci_cmd);
3365 /* Set swapper to enable I/O register access */
3366 s2io_set_swapper(sp);
3368 /* Restore the MSIX table entries from local variables */
3369 restore_xmsi_data(sp);
3371 /* Clear certain PCI/PCI-X fields after reset */
3372 if (sp->device_type == XFRAME_II_DEVICE) {
3373 /* Clear "detected parity error" bit */
3374 pci_write_config_word(sp->pdev, PCI_STATUS, 0x8000);
3376 /* Clearing PCIX Ecc status register */
3377 pci_write_config_dword(sp->pdev, 0x68, 0x7C);
3379 /* Clearing PCI_STATUS error reflected here */
3380 writeq(s2BIT(62), &bar0->txpic_int_reg);
3383 /* Reset device statistics maintained by OS */
3384 memset(&sp->stats, 0, sizeof (struct net_device_stats));
3386 up_cnt = sp->mac_control.stats_info->sw_stat.link_up_cnt;
3387 down_cnt = sp->mac_control.stats_info->sw_stat.link_down_cnt;
3388 up_time = sp->mac_control.stats_info->sw_stat.link_up_time;
3389 down_time = sp->mac_control.stats_info->sw_stat.link_down_time;
3390 reset_cnt = sp->mac_control.stats_info->sw_stat.soft_reset_cnt;
3391 mem_alloc_cnt = sp->mac_control.stats_info->sw_stat.mem_allocated;
3392 mem_free_cnt = sp->mac_control.stats_info->sw_stat.mem_freed;
3393 watchdog_cnt = sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt;
3394 /* save link up/down time/cnt, reset/memory/watchdog cnt */
3395 memset(sp->mac_control.stats_info, 0, sizeof(struct stat_block));
3396 /* restore link up/down time/cnt, reset/memory/watchdog cnt */
3397 sp->mac_control.stats_info->sw_stat.link_up_cnt = up_cnt;
3398 sp->mac_control.stats_info->sw_stat.link_down_cnt = down_cnt;
3399 sp->mac_control.stats_info->sw_stat.link_up_time = up_time;
3400 sp->mac_control.stats_info->sw_stat.link_down_time = down_time;
3401 sp->mac_control.stats_info->sw_stat.soft_reset_cnt = reset_cnt;
3402 sp->mac_control.stats_info->sw_stat.mem_allocated = mem_alloc_cnt;
3403 sp->mac_control.stats_info->sw_stat.mem_freed = mem_free_cnt;
3404 sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt = watchdog_cnt;
3406 /* SXE-002: Configure link and activity LED to turn it off */
3407 subid = sp->pdev->subsystem_device;
3408 if (((subid & 0xFF) >= 0x07) &&
3409 (sp->device_type == XFRAME_I_DEVICE)) {
3410 val64 = readq(&bar0->gpio_control);
3411 val64 |= 0x0000800000000000ULL;
3412 writeq(val64, &bar0->gpio_control);
3413 val64 = 0x0411040400000000ULL;
3414 writeq(val64, (void __iomem *)bar0 + 0x2700);
3418 * Clear spurious ECC interrupts that would have occured on
3419 * XFRAME II cards after reset.
3421 if (sp->device_type == XFRAME_II_DEVICE) {
3422 val64 = readq(&bar0->pcc_err_reg);
3423 writeq(val64, &bar0->pcc_err_reg);
3426 /* restore the previously assigned mac address */
3427 do_s2io_prog_unicast(sp->dev, (u8 *)&sp->def_mac_addr[0].mac_addr);
3429 sp->device_enabled_once = FALSE;
3433 * s2io_set_swapper - to set the swapper controle on the card
3434 * @sp : private member of the device structure,
3435 * pointer to the s2io_nic structure.
3436 * Description: Function to set the swapper control on the card
3437 * correctly depending on the 'endianness' of the system.
3439 * SUCCESS on success and FAILURE on failure.
3442 static int s2io_set_swapper(struct s2io_nic * sp)
3444 struct net_device *dev = sp->dev;
3445 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3446 u64 val64, valt, valr;
3449 * Set proper endian settings and verify the same by reading
3450 * the PIF Feed-back register.
3453 val64 = readq(&bar0->pif_rd_swapper_fb);
3454 if (val64 != 0x0123456789ABCDEFULL) {
3456 u64 value[] = { 0xC30000C3C30000C3ULL, /* FE=1, SE=1 */
3457 0x8100008181000081ULL, /* FE=1, SE=0 */
3458 0x4200004242000042ULL, /* FE=0, SE=1 */
3459 0}; /* FE=0, SE=0 */
3462 writeq(value[i], &bar0->swapper_ctrl);
3463 val64 = readq(&bar0->pif_rd_swapper_fb);
3464 if (val64 == 0x0123456789ABCDEFULL)
3469 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, ",
3471 DBG_PRINT(ERR_DBG, "feedback read %llx\n",
3472 (unsigned long long) val64);
3477 valr = readq(&bar0->swapper_ctrl);
3480 valt = 0x0123456789ABCDEFULL;
3481 writeq(valt, &bar0->xmsi_address);
3482 val64 = readq(&bar0->xmsi_address);
3486 u64 value[] = { 0x00C3C30000C3C300ULL, /* FE=1, SE=1 */
3487 0x0081810000818100ULL, /* FE=1, SE=0 */
3488 0x0042420000424200ULL, /* FE=0, SE=1 */
3489 0}; /* FE=0, SE=0 */
3492 writeq((value[i] | valr), &bar0->swapper_ctrl);
3493 writeq(valt, &bar0->xmsi_address);
3494 val64 = readq(&bar0->xmsi_address);
3500 unsigned long long x = val64;
3501 DBG_PRINT(ERR_DBG, "Write failed, Xmsi_addr ");
3502 DBG_PRINT(ERR_DBG, "reads:0x%llx\n", x);
3506 val64 = readq(&bar0->swapper_ctrl);
3507 val64 &= 0xFFFF000000000000ULL;
3511 * The device by default set to a big endian format, so a
3512 * big endian driver need not set anything.
3514 val64 |= (SWAPPER_CTRL_TXP_FE |
3515 SWAPPER_CTRL_TXP_SE |
3516 SWAPPER_CTRL_TXD_R_FE |
3517 SWAPPER_CTRL_TXD_W_FE |
3518 SWAPPER_CTRL_TXF_R_FE |
3519 SWAPPER_CTRL_RXD_R_FE |
3520 SWAPPER_CTRL_RXD_W_FE |
3521 SWAPPER_CTRL_RXF_W_FE |
3522 SWAPPER_CTRL_XMSI_FE |
3523 SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
3524 if (sp->config.intr_type == INTA)
3525 val64 |= SWAPPER_CTRL_XMSI_SE;
3526 writeq(val64, &bar0->swapper_ctrl);
3529 * Initially we enable all bits to make it accessible by the
3530 * driver, then we selectively enable only those bits that
3533 val64 |= (SWAPPER_CTRL_TXP_FE |
3534 SWAPPER_CTRL_TXP_SE |
3535 SWAPPER_CTRL_TXD_R_FE |
3536 SWAPPER_CTRL_TXD_R_SE |
3537 SWAPPER_CTRL_TXD_W_FE |
3538 SWAPPER_CTRL_TXD_W_SE |
3539 SWAPPER_CTRL_TXF_R_FE |
3540 SWAPPER_CTRL_RXD_R_FE |
3541 SWAPPER_CTRL_RXD_R_SE |
3542 SWAPPER_CTRL_RXD_W_FE |
3543 SWAPPER_CTRL_RXD_W_SE |
3544 SWAPPER_CTRL_RXF_W_FE |
3545 SWAPPER_CTRL_XMSI_FE |
3546 SWAPPER_CTRL_STATS_FE | SWAPPER_CTRL_STATS_SE);
3547 if (sp->config.intr_type == INTA)
3548 val64 |= SWAPPER_CTRL_XMSI_SE;
3549 writeq(val64, &bar0->swapper_ctrl);
3551 val64 = readq(&bar0->swapper_ctrl);
3554 * Verifying if endian settings are accurate by reading a
3555 * feedback register.
3557 val64 = readq(&bar0->pif_rd_swapper_fb);
3558 if (val64 != 0x0123456789ABCDEFULL) {
3559 /* Endian settings are incorrect, calls for another dekko. */
3560 DBG_PRINT(ERR_DBG, "%s: Endian settings are wrong, ",
3562 DBG_PRINT(ERR_DBG, "feedback read %llx\n",
3563 (unsigned long long) val64);
3570 static int wait_for_msix_trans(struct s2io_nic *nic, int i)
3572 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3574 int ret = 0, cnt = 0;
3577 val64 = readq(&bar0->xmsi_access);
3578 if (!(val64 & s2BIT(15)))
3584 DBG_PRINT(ERR_DBG, "XMSI # %d Access failed\n", i);
3591 static void restore_xmsi_data(struct s2io_nic *nic)
3593 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3597 for (i=0; i < MAX_REQUESTED_MSI_X; i++) {
3598 writeq(nic->msix_info[i].addr, &bar0->xmsi_address);
3599 writeq(nic->msix_info[i].data, &bar0->xmsi_data);
3600 val64 = (s2BIT(7) | s2BIT(15) | vBIT(i, 26, 6));
3601 writeq(val64, &bar0->xmsi_access);
3602 if (wait_for_msix_trans(nic, i)) {
3603 DBG_PRINT(ERR_DBG, "failed in %s\n", __FUNCTION__);
3609 static void store_xmsi_data(struct s2io_nic *nic)
3611 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3612 u64 val64, addr, data;
3615 /* Store and display */
3616 for (i=0; i < MAX_REQUESTED_MSI_X; i++) {
3617 val64 = (s2BIT(15) | vBIT(i, 26, 6));
3618 writeq(val64, &bar0->xmsi_access);
3619 if (wait_for_msix_trans(nic, i)) {
3620 DBG_PRINT(ERR_DBG, "failed in %s\n", __FUNCTION__);
3623 addr = readq(&bar0->xmsi_address);
3624 data = readq(&bar0->xmsi_data);
3626 nic->msix_info[i].addr = addr;
3627 nic->msix_info[i].data = data;
3632 static int s2io_enable_msi_x(struct s2io_nic *nic)
3634 struct XENA_dev_config __iomem *bar0 = nic->bar0;
3636 u16 msi_control; /* Temp variable */
3637 int ret, i, j, msix_indx = 1;
3639 nic->entries = kcalloc(MAX_REQUESTED_MSI_X, sizeof(struct msix_entry),
3641 if (!nic->entries) {
3642 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n", \
3644 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
3647 nic->mac_control.stats_info->sw_stat.mem_allocated
3648 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3651 kcalloc(MAX_REQUESTED_MSI_X, sizeof(struct s2io_msix_entry),
3653 if (!nic->s2io_entries) {
3654 DBG_PRINT(INFO_DBG, "%s: Memory allocation failed\n",
3656 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
3657 kfree(nic->entries);
3658 nic->mac_control.stats_info->sw_stat.mem_freed
3659 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3662 nic->mac_control.stats_info->sw_stat.mem_allocated
3663 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3665 for (i=0; i< MAX_REQUESTED_MSI_X; i++) {
3666 nic->entries[i].entry = i;
3667 nic->s2io_entries[i].entry = i;
3668 nic->s2io_entries[i].arg = NULL;
3669 nic->s2io_entries[i].in_use = 0;
3672 tx_mat = readq(&bar0->tx_mat0_n[0]);
3673 for (i=0; i<nic->config.tx_fifo_num; i++, msix_indx++) {
3674 tx_mat |= TX_MAT_SET(i, msix_indx);
3675 nic->s2io_entries[msix_indx].arg = &nic->mac_control.fifos[i];
3676 nic->s2io_entries[msix_indx].type = MSIX_FIFO_TYPE;
3677 nic->s2io_entries[msix_indx].in_use = MSIX_FLG;
3679 writeq(tx_mat, &bar0->tx_mat0_n[0]);
3681 rx_mat = readq(&bar0->rx_mat);
3682 for (j = 0; j < nic->config.rx_ring_num; j++, msix_indx++) {
3683 rx_mat |= RX_MAT_SET(j, msix_indx);
3684 nic->s2io_entries[msix_indx].arg
3685 = &nic->mac_control.rings[j];
3686 nic->s2io_entries[msix_indx].type = MSIX_RING_TYPE;
3687 nic->s2io_entries[msix_indx].in_use = MSIX_FLG;
3689 writeq(rx_mat, &bar0->rx_mat);
3691 nic->avail_msix_vectors = 0;
3692 ret = pci_enable_msix(nic->pdev, nic->entries, MAX_REQUESTED_MSI_X);
3693 /* We fail init if error or we get less vectors than min required */
3694 if (ret >= (nic->config.tx_fifo_num + nic->config.rx_ring_num + 1)) {
3695 nic->avail_msix_vectors = ret;
3696 ret = pci_enable_msix(nic->pdev, nic->entries, ret);
3699 DBG_PRINT(ERR_DBG, "%s: Enabling MSIX failed\n", nic->dev->name);
3700 kfree(nic->entries);
3701 nic->mac_control.stats_info->sw_stat.mem_freed
3702 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3703 kfree(nic->s2io_entries);
3704 nic->mac_control.stats_info->sw_stat.mem_freed
3705 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3706 nic->entries = NULL;
3707 nic->s2io_entries = NULL;
3708 nic->avail_msix_vectors = 0;
3711 if (!nic->avail_msix_vectors)
3712 nic->avail_msix_vectors = MAX_REQUESTED_MSI_X;
3715 * To enable MSI-X, MSI also needs to be enabled, due to a bug
3716 * in the herc NIC. (Temp change, needs to be removed later)
3718 pci_read_config_word(nic->pdev, 0x42, &msi_control);
3719 msi_control |= 0x1; /* Enable MSI */
3720 pci_write_config_word(nic->pdev, 0x42, msi_control);
3725 /* Handle software interrupt used during MSI(X) test */
3726 static irqreturn_t __devinit s2io_test_intr(int irq, void *dev_id)
3728 struct s2io_nic *sp = dev_id;
3730 sp->msi_detected = 1;
3731 wake_up(&sp->msi_wait);
3736 /* Test interrupt path by forcing a a software IRQ */
3737 static int __devinit s2io_test_msi(struct s2io_nic *sp)
3739 struct pci_dev *pdev = sp->pdev;
3740 struct XENA_dev_config __iomem *bar0 = sp->bar0;
3744 err = request_irq(sp->entries[1].vector, s2io_test_intr, 0,
3747 DBG_PRINT(ERR_DBG, "%s: PCI %s: cannot assign irq %d\n",
3748 sp->dev->name, pci_name(pdev), pdev->irq);
3752 init_waitqueue_head (&sp->msi_wait);
3753 sp->msi_detected = 0;
3755 saved64 = val64 = readq(&bar0->scheduled_int_ctrl);
3756 val64 |= SCHED_INT_CTRL_ONE_SHOT;
3757 val64 |= SCHED_INT_CTRL_TIMER_EN;
3758 val64 |= SCHED_INT_CTRL_INT2MSI(1);
3759 writeq(val64, &bar0->scheduled_int_ctrl);
3761 wait_event_timeout(sp->msi_wait, sp->msi_detected, HZ/10);
3763 if (!sp->msi_detected) {
3764 /* MSI(X) test failed, go back to INTx mode */
3765 DBG_PRINT(ERR_DBG, "%s: PCI %s: No interrupt was generated"
3766 "using MSI(X) during test\n", sp->dev->name,
3772 free_irq(sp->entries[1].vector, sp);
3774 writeq(saved64, &bar0->scheduled_int_ctrl);
3779 static void remove_msix_isr(struct s2io_nic *sp)
3784 for (i = 0; i < MAX_REQUESTED_MSI_X; i++) {
3785 if (sp->s2io_entries[i].in_use ==
3786 MSIX_REGISTERED_SUCCESS) {
3787 int vector = sp->entries[i].vector;
3788 void *arg = sp->s2io_entries[i].arg;
3789 free_irq(vector, arg);
3794 kfree(sp->s2io_entries);
3796 sp->s2io_entries = NULL;
3798 pci_read_config_word(sp->pdev, 0x42, &msi_control);
3799 msi_control &= 0xFFFE; /* Disable MSI */
3800 pci_write_config_word(sp->pdev, 0x42, msi_control);
3802 pci_disable_msix(sp->pdev);
3805 static void remove_inta_isr(struct s2io_nic *sp)
3807 struct net_device *dev = sp->dev;
3809 free_irq(sp->pdev->irq, dev);
3812 /* ********************************************************* *
3813 * Functions defined below concern the OS part of the driver *
3814 * ********************************************************* */
3817 * s2io_open - open entry point of the driver
3818 * @dev : pointer to the device structure.
3820 * This function is the open entry point of the driver. It mainly calls a
3821 * function to allocate Rx buffers and inserts them into the buffer
3822 * descriptors and then enables the Rx part of the NIC.
3824 * 0 on success and an appropriate (-)ve integer as defined in errno.h
3828 static int s2io_open(struct net_device *dev)
3830 struct s2io_nic *sp = dev->priv;
3834 * Make sure you have link off by default every time
3835 * Nic is initialized
3837 netif_carrier_off(dev);
3838 sp->last_link_state = 0;
3840 napi_enable(&sp->napi);
3842 if (sp->config.intr_type == MSI_X) {
3843 int ret = s2io_enable_msi_x(sp);
3846 ret = s2io_test_msi(sp);
3847 /* rollback MSI-X, will re-enable during add_isr() */
3848 remove_msix_isr(sp);
3853 "%s: MSI-X requested but failed to enable\n",
3855 sp->config.intr_type = INTA;
3859 /* NAPI doesn't work well with MSI(X) */
3860 if (sp->config.intr_type != INTA) {
3862 sp->config.napi = 0;
3865 /* Initialize H/W and enable interrupts */
3866 err = s2io_card_up(sp);
3868 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
3870 goto hw_init_failed;
3873 if (do_s2io_prog_unicast(dev, dev->dev_addr) == FAILURE) {
3874 DBG_PRINT(ERR_DBG, "Set Mac Address Failed\n");
3877 goto hw_init_failed;
3880 netif_start_queue(dev);
3884 napi_disable(&sp->napi);
3885 if (sp->config.intr_type == MSI_X) {
3888 sp->mac_control.stats_info->sw_stat.mem_freed
3889 += (MAX_REQUESTED_MSI_X * sizeof(struct msix_entry));
3891 if (sp->s2io_entries) {
3892 kfree(sp->s2io_entries);
3893 sp->mac_control.stats_info->sw_stat.mem_freed
3894 += (MAX_REQUESTED_MSI_X * sizeof(struct s2io_msix_entry));
3901 * s2io_close -close entry point of the driver
3902 * @dev : device pointer.
3904 * This is the stop entry point of the driver. It needs to undo exactly
3905 * whatever was done by the open entry point,thus it's usually referred to
3906 * as the close function.Among other things this function mainly stops the
3907 * Rx side of the NIC and frees all the Rx buffers in the Rx rings.
3909 * 0 on success and an appropriate (-)ve integer as defined in errno.h
3913 static int s2io_close(struct net_device *dev)
3915 struct s2io_nic *sp = dev->priv;
3917 netif_stop_queue(dev);
3918 napi_disable(&sp->napi);
3919 /* Reset card, kill tasklet and free Tx and Rx buffers. */
3926 * s2io_xmit - Tx entry point of te driver
3927 * @skb : the socket buffer containing the Tx data.
3928 * @dev : device pointer.
3930 * This function is the Tx entry point of the driver. S2IO NIC supports
3931 * certain protocol assist features on Tx side, namely CSO, S/G, LSO.
3932 * NOTE: when device cant queue the pkt,just the trans_start variable will
3935 * 0 on success & 1 on failure.
3938 static int s2io_xmit(struct sk_buff *skb, struct net_device *dev)
3940 struct s2io_nic *sp = dev->priv;
3941 u16 frg_cnt, frg_len, i, queue, queue_len, put_off, get_off;
3944 struct TxFIFO_element __iomem *tx_fifo;
3945 unsigned long flags;
3947 int vlan_priority = 0;
3948 struct mac_info *mac_control;
3949 struct config_param *config;
3951 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
3953 mac_control = &sp->mac_control;
3954 config = &sp->config;
3956 DBG_PRINT(TX_DBG, "%s: In Neterion Tx routine\n", dev->name);
3958 if (unlikely(skb->len <= 0)) {
3959 DBG_PRINT(TX_DBG, "%s:Buffer has no data..\n", dev->name);
3960 dev_kfree_skb_any(skb);
3964 spin_lock_irqsave(&sp->tx_lock, flags);
3965 if (!is_s2io_card_up(sp)) {
3966 DBG_PRINT(TX_DBG, "%s: Card going down for reset\n",
3968 spin_unlock_irqrestore(&sp->tx_lock, flags);
3974 /* Get Fifo number to Transmit based on vlan priority */
3975 if (sp->vlgrp && vlan_tx_tag_present(skb)) {
3976 vlan_tag = vlan_tx_tag_get(skb);
3977 vlan_priority = vlan_tag >> 13;
3978 queue = config->fifo_mapping[vlan_priority];
3981 put_off = (u16) mac_control->fifos[queue].tx_curr_put_info.offset;
3982 get_off = (u16) mac_control->fifos[queue].tx_curr_get_info.offset;
3983 txdp = (struct TxD *) mac_control->fifos[queue].list_info[put_off].
3986 queue_len = mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1;
3987 /* Avoid "put" pointer going beyond "get" pointer */
3988 if (txdp->Host_Control ||
3989 ((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
3990 DBG_PRINT(TX_DBG, "Error in xmit, No free TXDs.\n");
3991 netif_stop_queue(dev);
3993 spin_unlock_irqrestore(&sp->tx_lock, flags);
3997 offload_type = s2io_offload_type(skb);
3998 if (offload_type & (SKB_GSO_TCPV4 | SKB_GSO_TCPV6)) {
3999 txdp->Control_1 |= TXD_TCP_LSO_EN;
4000 txdp->Control_1 |= TXD_TCP_LSO_MSS(s2io_tcp_mss(skb));
4002 if (skb->ip_summed == CHECKSUM_PARTIAL) {
4004 (TXD_TX_CKO_IPV4_EN | TXD_TX_CKO_TCP_EN |
4007 txdp->Control_1 |= TXD_GATHER_CODE_FIRST;
4008 txdp->Control_1 |= TXD_LIST_OWN_XENA;
4009 txdp->Control_2 |= config->tx_intr_type;
4011 if (sp->vlgrp && vlan_tx_tag_present(skb)) {
4012 txdp->Control_2 |= TXD_VLAN_ENABLE;
4013 txdp->Control_2 |= TXD_VLAN_TAG(vlan_tag);
4016 frg_len = skb->len - skb->data_len;
4017 if (offload_type == SKB_GSO_UDP) {
4020 ufo_size = s2io_udp_mss(skb);
4022 txdp->Control_1 |= TXD_UFO_EN;
4023 txdp->Control_1 |= TXD_UFO_MSS(ufo_size);
4024 txdp->Control_1 |= TXD_BUFFER0_SIZE(8);
4026 sp->ufo_in_band_v[put_off] =
4027 (u64)skb_shinfo(skb)->ip6_frag_id;
4029 sp->ufo_in_band_v[put_off] =
4030 (u64)skb_shinfo(skb)->ip6_frag_id << 32;
4032 txdp->Host_Control = (unsigned long)sp->ufo_in_band_v;
4033 txdp->Buffer_Pointer = pci_map_single(sp->pdev,
4035 sizeof(u64), PCI_DMA_TODEVICE);
4036 if((txdp->Buffer_Pointer == 0) ||
4037 (txdp->Buffer_Pointer == DMA_ERROR_CODE))
4038 goto pci_map_failed;
4042 txdp->Buffer_Pointer = pci_map_single
4043 (sp->pdev, skb->data, frg_len, PCI_DMA_TODEVICE);
4044 if((txdp->Buffer_Pointer == 0) ||
4045 (txdp->Buffer_Pointer == DMA_ERROR_CODE))
4046 goto pci_map_failed;
4048 txdp->Host_Control = (unsigned long) skb;
4049 txdp->Control_1 |= TXD_BUFFER0_SIZE(frg_len);
4050 if (offload_type == SKB_GSO_UDP)
4051 txdp->Control_1 |= TXD_UFO_EN;
4053 frg_cnt = skb_shinfo(skb)->nr_frags;
4054 /* For fragmented SKB. */
4055 for (i = 0; i < frg_cnt; i++) {
4056 skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
4057 /* A '0' length fragment will be ignored */
4061 txdp->Buffer_Pointer = (u64) pci_map_page
4062 (sp->pdev, frag->page, frag->page_offset,
4063 frag->size, PCI_DMA_TODEVICE);
4064 txdp->Control_1 = TXD_BUFFER0_SIZE(frag->size);
4065 if (offload_type == SKB_GSO_UDP)
4066 txdp->Control_1 |= TXD_UFO_EN;
4068 txdp->Control_1 |= TXD_GATHER_CODE_LAST;
4070 if (offload_type == SKB_GSO_UDP)
4071 frg_cnt++; /* as Txd0 was used for inband header */
4073 tx_fifo = mac_control->tx_FIFO_start[queue];
4074 val64 = mac_control->fifos[queue].list_info[put_off].list_phy_addr;
4075 writeq(val64, &tx_fifo->TxDL_Pointer);
4077 val64 = (TX_FIFO_LAST_TXD_NUM(frg_cnt) | TX_FIFO_FIRST_LIST |
4080 val64 |= TX_FIFO_SPECIAL_FUNC;
4082 writeq(val64, &tx_fifo->List_Control);
4087 if (put_off == mac_control->fifos[queue].tx_curr_put_info.fifo_len + 1)
4089 mac_control->fifos[queue].tx_curr_put_info.offset = put_off;
4091 /* Avoid "put" pointer going beyond "get" pointer */
4092 if (((put_off+1) == queue_len ? 0 : (put_off+1)) == get_off) {
4093 sp->mac_control.stats_info->sw_stat.fifo_full_cnt++;
4095 "No free TxDs for xmit, Put: 0x%x Get:0x%x\n",
4097 netif_stop_queue(dev);
4099 mac_control->stats_info->sw_stat.mem_allocated += skb->truesize;
4100 dev->trans_start = jiffies;
4101 spin_unlock_irqrestore(&sp->tx_lock, flags);
4105 stats->pci_map_fail_cnt++;
4106 netif_stop_queue(dev);
4107 stats->mem_freed += skb->truesize;
4109 spin_unlock_irqrestore(&sp->tx_lock, flags);
4114 s2io_alarm_handle(unsigned long data)
4116 struct s2io_nic *sp = (struct s2io_nic *)data;
4117 struct net_device *dev = sp->dev;
4119 s2io_handle_errors(dev);
4120 mod_timer(&sp->alarm_timer, jiffies + HZ / 2);
4123 static int s2io_chk_rx_buffers(struct s2io_nic *sp, int rng_n)
4125 int rxb_size, level;
4128 rxb_size = atomic_read(&sp->rx_bufs_left[rng_n]);
4129 level = rx_buffer_level(sp, rxb_size, rng_n);
4131 if ((level == PANIC) && (!TASKLET_IN_USE)) {
4133 DBG_PRINT(INTR_DBG, "%s: Rx BD hit ", __FUNCTION__);
4134 DBG_PRINT(INTR_DBG, "PANIC levels\n");
4135 if ((ret = fill_rx_buffers(sp, rng_n)) == -ENOMEM) {
4136 DBG_PRINT(INFO_DBG, "Out of memory in %s",
4138 clear_bit(0, (&sp->tasklet_status));
4141 clear_bit(0, (&sp->tasklet_status));
4142 } else if (level == LOW)
4143 tasklet_schedule(&sp->task);
4145 } else if (fill_rx_buffers(sp, rng_n) == -ENOMEM) {
4146 DBG_PRINT(INFO_DBG, "%s:Out of memory", sp->dev->name);
4147 DBG_PRINT(INFO_DBG, " in Rx Intr!!\n");
4152 static irqreturn_t s2io_msix_ring_handle(int irq, void *dev_id)
4154 struct ring_info *ring = (struct ring_info *)dev_id;
4155 struct s2io_nic *sp = ring->nic;
4157 if (!is_s2io_card_up(sp))
4160 rx_intr_handler(ring);
4161 s2io_chk_rx_buffers(sp, ring->ring_no);
4166 static irqreturn_t s2io_msix_fifo_handle(int irq, void *dev_id)
4168 struct fifo_info *fifo = (struct fifo_info *)dev_id;
4169 struct s2io_nic *sp = fifo->nic;
4171 if (!is_s2io_card_up(sp))
4174 tx_intr_handler(fifo);
4177 static void s2io_txpic_intr_handle(struct s2io_nic *sp)
4179 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4182 val64 = readq(&bar0->pic_int_status);
4183 if (val64 & PIC_INT_GPIO) {
4184 val64 = readq(&bar0->gpio_int_reg);
4185 if ((val64 & GPIO_INT_REG_LINK_DOWN) &&
4186 (val64 & GPIO_INT_REG_LINK_UP)) {
4188 * This is unstable state so clear both up/down
4189 * interrupt and adapter to re-evaluate the link state.
4191 val64 |= GPIO_INT_REG_LINK_DOWN;
4192 val64 |= GPIO_INT_REG_LINK_UP;
4193 writeq(val64, &bar0->gpio_int_reg);
4194 val64 = readq(&bar0->gpio_int_mask);
4195 val64 &= ~(GPIO_INT_MASK_LINK_UP |
4196 GPIO_INT_MASK_LINK_DOWN);
4197 writeq(val64, &bar0->gpio_int_mask);
4199 else if (val64 & GPIO_INT_REG_LINK_UP) {
4200 val64 = readq(&bar0->adapter_status);
4201 /* Enable Adapter */
4202 val64 = readq(&bar0->adapter_control);
4203 val64 |= ADAPTER_CNTL_EN;
4204 writeq(val64, &bar0->adapter_control);
4205 val64 |= ADAPTER_LED_ON;
4206 writeq(val64, &bar0->adapter_control);
4207 if (!sp->device_enabled_once)
4208 sp->device_enabled_once = 1;
4210 s2io_link(sp, LINK_UP);
4212 * unmask link down interrupt and mask link-up
4215 val64 = readq(&bar0->gpio_int_mask);
4216 val64 &= ~GPIO_INT_MASK_LINK_DOWN;
4217 val64 |= GPIO_INT_MASK_LINK_UP;
4218 writeq(val64, &bar0->gpio_int_mask);
4220 }else if (val64 & GPIO_INT_REG_LINK_DOWN) {
4221 val64 = readq(&bar0->adapter_status);
4222 s2io_link(sp, LINK_DOWN);
4223 /* Link is down so unmaks link up interrupt */
4224 val64 = readq(&bar0->gpio_int_mask);
4225 val64 &= ~GPIO_INT_MASK_LINK_UP;
4226 val64 |= GPIO_INT_MASK_LINK_DOWN;
4227 writeq(val64, &bar0->gpio_int_mask);
4230 val64 = readq(&bar0->adapter_control);
4231 val64 = val64 &(~ADAPTER_LED_ON);
4232 writeq(val64, &bar0->adapter_control);
4235 val64 = readq(&bar0->gpio_int_mask);
4239 * do_s2io_chk_alarm_bit - Check for alarm and incrment the counter
4240 * @value: alarm bits
4241 * @addr: address value
4242 * @cnt: counter variable
4243 * Description: Check for alarm and increment the counter
4245 * 1 - if alarm bit set
4246 * 0 - if alarm bit is not set
4248 static int do_s2io_chk_alarm_bit(u64 value, void __iomem * addr,
4249 unsigned long long *cnt)
4252 val64 = readq(addr);
4253 if ( val64 & value ) {
4254 writeq(val64, addr);
4263 * s2io_handle_errors - Xframe error indication handler
4264 * @nic: device private variable
4265 * Description: Handle alarms such as loss of link, single or
4266 * double ECC errors, critical and serious errors.
4270 static void s2io_handle_errors(void * dev_id)
4272 struct net_device *dev = (struct net_device *) dev_id;
4273 struct s2io_nic *sp = dev->priv;
4274 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4275 u64 temp64 = 0,val64=0;
4278 struct swStat *sw_stat = &sp->mac_control.stats_info->sw_stat;
4279 struct xpakStat *stats = &sp->mac_control.stats_info->xpak_stat;
4281 if (!is_s2io_card_up(sp))
4284 if (pci_channel_offline(sp->pdev))
4287 memset(&sw_stat->ring_full_cnt, 0,
4288 sizeof(sw_stat->ring_full_cnt));
4290 /* Handling the XPAK counters update */
4291 if(stats->xpak_timer_count < 72000) {
4292 /* waiting for an hour */
4293 stats->xpak_timer_count++;
4295 s2io_updt_xpak_counter(dev);
4296 /* reset the count to zero */
4297 stats->xpak_timer_count = 0;
4300 /* Handling link status change error Intr */
4301 if (s2io_link_fault_indication(sp) == MAC_RMAC_ERR_TIMER) {
4302 val64 = readq(&bar0->mac_rmac_err_reg);
4303 writeq(val64, &bar0->mac_rmac_err_reg);
4304 if (val64 & RMAC_LINK_STATE_CHANGE_INT)
4305 schedule_work(&sp->set_link_task);
4308 /* In case of a serious error, the device will be Reset. */
4309 if (do_s2io_chk_alarm_bit(SERR_SOURCE_ANY, &bar0->serr_source,
4310 &sw_stat->serious_err_cnt))
4313 /* Check for data parity error */
4314 if (do_s2io_chk_alarm_bit(GPIO_INT_REG_DP_ERR_INT, &bar0->gpio_int_reg,
4315 &sw_stat->parity_err_cnt))
4318 /* Check for ring full counter */
4319 if (sp->device_type == XFRAME_II_DEVICE) {
4320 val64 = readq(&bar0->ring_bump_counter1);
4321 for (i=0; i<4; i++) {
4322 temp64 = ( val64 & vBIT(0xFFFF,(i*16),16));
4323 temp64 >>= 64 - ((i+1)*16);
4324 sw_stat->ring_full_cnt[i] += temp64;
4327 val64 = readq(&bar0->ring_bump_counter2);
4328 for (i=0; i<4; i++) {
4329 temp64 = ( val64 & vBIT(0xFFFF,(i*16),16));
4330 temp64 >>= 64 - ((i+1)*16);
4331 sw_stat->ring_full_cnt[i+4] += temp64;
4335 val64 = readq(&bar0->txdma_int_status);
4336 /*check for pfc_err*/
4337 if (val64 & TXDMA_PFC_INT) {
4338 if (do_s2io_chk_alarm_bit(PFC_ECC_DB_ERR | PFC_SM_ERR_ALARM|
4339 PFC_MISC_0_ERR | PFC_MISC_1_ERR|
4340 PFC_PCIX_ERR, &bar0->pfc_err_reg,
4341 &sw_stat->pfc_err_cnt))
4343 do_s2io_chk_alarm_bit(PFC_ECC_SG_ERR, &bar0->pfc_err_reg,
4344 &sw_stat->pfc_err_cnt);
4347 /*check for tda_err*/
4348 if (val64 & TXDMA_TDA_INT) {
4349 if(do_s2io_chk_alarm_bit(TDA_Fn_ECC_DB_ERR | TDA_SM0_ERR_ALARM |
4350 TDA_SM1_ERR_ALARM, &bar0->tda_err_reg,
4351 &sw_stat->tda_err_cnt))
4353 do_s2io_chk_alarm_bit(TDA_Fn_ECC_SG_ERR | TDA_PCIX_ERR,
4354 &bar0->tda_err_reg, &sw_stat->tda_err_cnt);
4356 /*check for pcc_err*/
4357 if (val64 & TXDMA_PCC_INT) {
4358 if (do_s2io_chk_alarm_bit(PCC_SM_ERR_ALARM | PCC_WR_ERR_ALARM
4359 | PCC_N_SERR | PCC_6_COF_OV_ERR
4360 | PCC_7_COF_OV_ERR | PCC_6_LSO_OV_ERR
4361 | PCC_7_LSO_OV_ERR | PCC_FB_ECC_DB_ERR
4362 | PCC_TXB_ECC_DB_ERR, &bar0->pcc_err_reg,
4363 &sw_stat->pcc_err_cnt))
4365 do_s2io_chk_alarm_bit(PCC_FB_ECC_SG_ERR | PCC_TXB_ECC_SG_ERR,
4366 &bar0->pcc_err_reg, &sw_stat->pcc_err_cnt);
4369 /*check for tti_err*/
4370 if (val64 & TXDMA_TTI_INT) {
4371 if (do_s2io_chk_alarm_bit(TTI_SM_ERR_ALARM, &bar0->tti_err_reg,
4372 &sw_stat->tti_err_cnt))
4374 do_s2io_chk_alarm_bit(TTI_ECC_SG_ERR | TTI_ECC_DB_ERR,
4375 &bar0->tti_err_reg, &sw_stat->tti_err_cnt);
4378 /*check for lso_err*/
4379 if (val64 & TXDMA_LSO_INT) {
4380 if (do_s2io_chk_alarm_bit(LSO6_ABORT | LSO7_ABORT
4381 | LSO6_SM_ERR_ALARM | LSO7_SM_ERR_ALARM,
4382 &bar0->lso_err_reg, &sw_stat->lso_err_cnt))
4384 do_s2io_chk_alarm_bit(LSO6_SEND_OFLOW | LSO7_SEND_OFLOW,
4385 &bar0->lso_err_reg, &sw_stat->lso_err_cnt);
4388 /*check for tpa_err*/
4389 if (val64 & TXDMA_TPA_INT) {
4390 if (do_s2io_chk_alarm_bit(TPA_SM_ERR_ALARM, &bar0->tpa_err_reg,
4391 &sw_stat->tpa_err_cnt))
4393 do_s2io_chk_alarm_bit(TPA_TX_FRM_DROP, &bar0->tpa_err_reg,
4394 &sw_stat->tpa_err_cnt);
4397 /*check for sm_err*/
4398 if (val64 & TXDMA_SM_INT) {
4399 if (do_s2io_chk_alarm_bit(SM_SM_ERR_ALARM, &bar0->sm_err_reg,
4400 &sw_stat->sm_err_cnt))
4404 val64 = readq(&bar0->mac_int_status);
4405 if (val64 & MAC_INT_STATUS_TMAC_INT) {
4406 if (do_s2io_chk_alarm_bit(TMAC_TX_BUF_OVRN | TMAC_TX_SM_ERR,
4407 &bar0->mac_tmac_err_reg,
4408 &sw_stat->mac_tmac_err_cnt))
4410 do_s2io_chk_alarm_bit(TMAC_ECC_SG_ERR | TMAC_ECC_DB_ERR
4411 | TMAC_DESC_ECC_SG_ERR | TMAC_DESC_ECC_DB_ERR,
4412 &bar0->mac_tmac_err_reg,
4413 &sw_stat->mac_tmac_err_cnt);
4416 val64 = readq(&bar0->xgxs_int_status);
4417 if (val64 & XGXS_INT_STATUS_TXGXS) {
4418 if (do_s2io_chk_alarm_bit(TXGXS_ESTORE_UFLOW | TXGXS_TX_SM_ERR,
4419 &bar0->xgxs_txgxs_err_reg,
4420 &sw_stat->xgxs_txgxs_err_cnt))
4422 do_s2io_chk_alarm_bit(TXGXS_ECC_SG_ERR | TXGXS_ECC_DB_ERR,
4423 &bar0->xgxs_txgxs_err_reg,
4424 &sw_stat->xgxs_txgxs_err_cnt);
4427 val64 = readq(&bar0->rxdma_int_status);
4428 if (val64 & RXDMA_INT_RC_INT_M) {
4429 if (do_s2io_chk_alarm_bit(RC_PRCn_ECC_DB_ERR | RC_FTC_ECC_DB_ERR
4430 | RC_PRCn_SM_ERR_ALARM |RC_FTC_SM_ERR_ALARM,
4431 &bar0->rc_err_reg, &sw_stat->rc_err_cnt))
4433 do_s2io_chk_alarm_bit(RC_PRCn_ECC_SG_ERR | RC_FTC_ECC_SG_ERR
4434 | RC_RDA_FAIL_WR_Rn, &bar0->rc_err_reg,
4435 &sw_stat->rc_err_cnt);
4436 if (do_s2io_chk_alarm_bit(PRC_PCI_AB_RD_Rn | PRC_PCI_AB_WR_Rn
4437 | PRC_PCI_AB_F_WR_Rn, &bar0->prc_pcix_err_reg,
4438 &sw_stat->prc_pcix_err_cnt))
4440 do_s2io_chk_alarm_bit(PRC_PCI_DP_RD_Rn | PRC_PCI_DP_WR_Rn
4441 | PRC_PCI_DP_F_WR_Rn, &bar0->prc_pcix_err_reg,
4442 &sw_stat->prc_pcix_err_cnt);
4445 if (val64 & RXDMA_INT_RPA_INT_M) {
4446 if (do_s2io_chk_alarm_bit(RPA_SM_ERR_ALARM | RPA_CREDIT_ERR,
4447 &bar0->rpa_err_reg, &sw_stat->rpa_err_cnt))
4449 do_s2io_chk_alarm_bit(RPA_ECC_SG_ERR | RPA_ECC_DB_ERR,
4450 &bar0->rpa_err_reg, &sw_stat->rpa_err_cnt);
4453 if (val64 & RXDMA_INT_RDA_INT_M) {
4454 if (do_s2io_chk_alarm_bit(RDA_RXDn_ECC_DB_ERR
4455 | RDA_FRM_ECC_DB_N_AERR | RDA_SM1_ERR_ALARM
4456 | RDA_SM0_ERR_ALARM | RDA_RXD_ECC_DB_SERR,
4457 &bar0->rda_err_reg, &sw_stat->rda_err_cnt))
4459 do_s2io_chk_alarm_bit(RDA_RXDn_ECC_SG_ERR | RDA_FRM_ECC_SG_ERR
4460 | RDA_MISC_ERR | RDA_PCIX_ERR,
4461 &bar0->rda_err_reg, &sw_stat->rda_err_cnt);
4464 if (val64 & RXDMA_INT_RTI_INT_M) {
4465 if (do_s2io_chk_alarm_bit(RTI_SM_ERR_ALARM, &bar0->rti_err_reg,
4466 &sw_stat->rti_err_cnt))
4468 do_s2io_chk_alarm_bit(RTI_ECC_SG_ERR | RTI_ECC_DB_ERR,
4469 &bar0->rti_err_reg, &sw_stat->rti_err_cnt);
4472 val64 = readq(&bar0->mac_int_status);
4473 if (val64 & MAC_INT_STATUS_RMAC_INT) {
4474 if (do_s2io_chk_alarm_bit(RMAC_RX_BUFF_OVRN | RMAC_RX_SM_ERR,
4475 &bar0->mac_rmac_err_reg,
4476 &sw_stat->mac_rmac_err_cnt))
4478 do_s2io_chk_alarm_bit(RMAC_UNUSED_INT|RMAC_SINGLE_ECC_ERR|
4479 RMAC_DOUBLE_ECC_ERR, &bar0->mac_rmac_err_reg,
4480 &sw_stat->mac_rmac_err_cnt);
4483 val64 = readq(&bar0->xgxs_int_status);
4484 if (val64 & XGXS_INT_STATUS_RXGXS) {
4485 if (do_s2io_chk_alarm_bit(RXGXS_ESTORE_OFLOW | RXGXS_RX_SM_ERR,
4486 &bar0->xgxs_rxgxs_err_reg,
4487 &sw_stat->xgxs_rxgxs_err_cnt))
4491 val64 = readq(&bar0->mc_int_status);
4492 if(val64 & MC_INT_STATUS_MC_INT) {
4493 if (do_s2io_chk_alarm_bit(MC_ERR_REG_SM_ERR, &bar0->mc_err_reg,
4494 &sw_stat->mc_err_cnt))
4497 /* Handling Ecc errors */
4498 if (val64 & (MC_ERR_REG_ECC_ALL_SNG | MC_ERR_REG_ECC_ALL_DBL)) {
4499 writeq(val64, &bar0->mc_err_reg);
4500 if (val64 & MC_ERR_REG_ECC_ALL_DBL) {
4501 sw_stat->double_ecc_errs++;
4502 if (sp->device_type != XFRAME_II_DEVICE) {
4504 * Reset XframeI only if critical error
4507 (MC_ERR_REG_MIRI_ECC_DB_ERR_0 |
4508 MC_ERR_REG_MIRI_ECC_DB_ERR_1))
4512 sw_stat->single_ecc_errs++;
4518 netif_stop_queue(dev);
4519 schedule_work(&sp->rst_timer_task);
4520 sw_stat->soft_reset_cnt++;
4525 * s2io_isr - ISR handler of the device .
4526 * @irq: the irq of the device.
4527 * @dev_id: a void pointer to the dev structure of the NIC.
4528 * Description: This function is the ISR handler of the device. It
4529 * identifies the reason for the interrupt and calls the relevant
4530 * service routines. As a contongency measure, this ISR allocates the
4531 * recv buffers, if their numbers are below the panic value which is
4532 * presently set to 25% of the original number of rcv buffers allocated.
4534 * IRQ_HANDLED: will be returned if IRQ was handled by this routine
4535 * IRQ_NONE: will be returned if interrupt is not from our device
4537 static irqreturn_t s2io_isr(int irq, void *dev_id)
4539 struct net_device *dev = (struct net_device *) dev_id;
4540 struct s2io_nic *sp = dev->priv;
4541 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4544 struct mac_info *mac_control;
4545 struct config_param *config;
4547 /* Pretend we handled any irq's from a disconnected card */
4548 if (pci_channel_offline(sp->pdev))
4551 if (!is_s2io_card_up(sp))
4554 mac_control = &sp->mac_control;
4555 config = &sp->config;
4558 * Identify the cause for interrupt and call the appropriate
4559 * interrupt handler. Causes for the interrupt could be;
4564 reason = readq(&bar0->general_int_status);
4566 if (unlikely(reason == S2IO_MINUS_ONE) ) {
4567 /* Nothing much can be done. Get out */
4571 if (reason & (GEN_INTR_RXTRAFFIC |
4572 GEN_INTR_TXTRAFFIC | GEN_INTR_TXPIC))
4574 writeq(S2IO_MINUS_ONE, &bar0->general_int_mask);
4577 if (reason & GEN_INTR_RXTRAFFIC) {
4578 if (likely(netif_rx_schedule_prep(dev,
4580 __netif_rx_schedule(dev, &sp->napi);
4581 writeq(S2IO_MINUS_ONE,
4582 &bar0->rx_traffic_mask);
4584 writeq(S2IO_MINUS_ONE,
4585 &bar0->rx_traffic_int);
4589 * rx_traffic_int reg is an R1 register, writing all 1's
4590 * will ensure that the actual interrupt causing bit
4591 * get's cleared and hence a read can be avoided.
4593 if (reason & GEN_INTR_RXTRAFFIC)
4594 writeq(S2IO_MINUS_ONE, &bar0->rx_traffic_int);
4596 for (i = 0; i < config->rx_ring_num; i++)
4597 rx_intr_handler(&mac_control->rings[i]);
4601 * tx_traffic_int reg is an R1 register, writing all 1's
4602 * will ensure that the actual interrupt causing bit get's
4603 * cleared and hence a read can be avoided.
4605 if (reason & GEN_INTR_TXTRAFFIC)
4606 writeq(S2IO_MINUS_ONE, &bar0->tx_traffic_int);
4608 for (i = 0; i < config->tx_fifo_num; i++)
4609 tx_intr_handler(&mac_control->fifos[i]);
4611 if (reason & GEN_INTR_TXPIC)
4612 s2io_txpic_intr_handle(sp);
4615 * Reallocate the buffers from the interrupt handler itself.
4617 if (!config->napi) {
4618 for (i = 0; i < config->rx_ring_num; i++)
4619 s2io_chk_rx_buffers(sp, i);
4621 writeq(sp->general_int_mask, &bar0->general_int_mask);
4622 readl(&bar0->general_int_status);
4628 /* The interrupt was not raised by us */
4638 static void s2io_updt_stats(struct s2io_nic *sp)
4640 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4644 if (is_s2io_card_up(sp)) {
4645 /* Apprx 30us on a 133 MHz bus */
4646 val64 = SET_UPDT_CLICKS(10) |
4647 STAT_CFG_ONE_SHOT_EN | STAT_CFG_STAT_EN;
4648 writeq(val64, &bar0->stat_cfg);
4651 val64 = readq(&bar0->stat_cfg);
4652 if (!(val64 & s2BIT(0)))
4656 break; /* Updt failed */
4662 * s2io_get_stats - Updates the device statistics structure.
4663 * @dev : pointer to the device structure.
4665 * This function updates the device statistics structure in the s2io_nic
4666 * structure and returns a pointer to the same.
4668 * pointer to the updated net_device_stats structure.
4671 static struct net_device_stats *s2io_get_stats(struct net_device *dev)
4673 struct s2io_nic *sp = dev->priv;
4674 struct mac_info *mac_control;
4675 struct config_param *config;
4678 mac_control = &sp->mac_control;
4679 config = &sp->config;
4681 /* Configure Stats for immediate updt */
4682 s2io_updt_stats(sp);
4684 sp->stats.tx_packets =
4685 le32_to_cpu(mac_control->stats_info->tmac_frms);
4686 sp->stats.tx_errors =
4687 le32_to_cpu(mac_control->stats_info->tmac_any_err_frms);
4688 sp->stats.rx_errors =
4689 le64_to_cpu(mac_control->stats_info->rmac_drop_frms);
4690 sp->stats.multicast =
4691 le32_to_cpu(mac_control->stats_info->rmac_vld_mcst_frms);
4692 sp->stats.rx_length_errors =
4693 le64_to_cpu(mac_control->stats_info->rmac_long_frms);
4695 return (&sp->stats);
4699 * s2io_set_multicast - entry point for multicast address enable/disable.
4700 * @dev : pointer to the device structure
4702 * This function is a driver entry point which gets called by the kernel
4703 * whenever multicast addresses must be enabled/disabled. This also gets
4704 * called to set/reset promiscuous mode. Depending on the deivce flag, we
4705 * determine, if multicast address must be enabled or if promiscuous mode
4706 * is to be disabled etc.
4711 static void s2io_set_multicast(struct net_device *dev)
4714 struct dev_mc_list *mclist;
4715 struct s2io_nic *sp = dev->priv;
4716 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4717 u64 val64 = 0, multi_mac = 0x010203040506ULL, mask =
4719 u64 dis_addr = 0xffffffffffffULL, mac_addr = 0;
4722 if ((dev->flags & IFF_ALLMULTI) && (!sp->m_cast_flg)) {
4723 /* Enable all Multicast addresses */
4724 writeq(RMAC_ADDR_DATA0_MEM_ADDR(multi_mac),
4725 &bar0->rmac_addr_data0_mem);
4726 writeq(RMAC_ADDR_DATA1_MEM_MASK(mask),
4727 &bar0->rmac_addr_data1_mem);
4728 val64 = RMAC_ADDR_CMD_MEM_WE |
4729 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4730 RMAC_ADDR_CMD_MEM_OFFSET(MAC_MC_ALL_MC_ADDR_OFFSET);
4731 writeq(val64, &bar0->rmac_addr_cmd_mem);
4732 /* Wait till command completes */
4733 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4734 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4738 sp->all_multi_pos = MAC_MC_ALL_MC_ADDR_OFFSET;
4739 } else if ((dev->flags & IFF_ALLMULTI) && (sp->m_cast_flg)) {
4740 /* Disable all Multicast addresses */
4741 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
4742 &bar0->rmac_addr_data0_mem);
4743 writeq(RMAC_ADDR_DATA1_MEM_MASK(0x0),
4744 &bar0->rmac_addr_data1_mem);
4745 val64 = RMAC_ADDR_CMD_MEM_WE |
4746 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4747 RMAC_ADDR_CMD_MEM_OFFSET(sp->all_multi_pos);
4748 writeq(val64, &bar0->rmac_addr_cmd_mem);
4749 /* Wait till command completes */
4750 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4751 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4755 sp->all_multi_pos = 0;
4758 if ((dev->flags & IFF_PROMISC) && (!sp->promisc_flg)) {
4759 /* Put the NIC into promiscuous mode */
4760 add = &bar0->mac_cfg;
4761 val64 = readq(&bar0->mac_cfg);
4762 val64 |= MAC_CFG_RMAC_PROM_ENABLE;
4764 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
4765 writel((u32) val64, add);
4766 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
4767 writel((u32) (val64 >> 32), (add + 4));
4769 if (vlan_tag_strip != 1) {
4770 val64 = readq(&bar0->rx_pa_cfg);
4771 val64 &= ~RX_PA_CFG_STRIP_VLAN_TAG;
4772 writeq(val64, &bar0->rx_pa_cfg);
4773 vlan_strip_flag = 0;
4776 val64 = readq(&bar0->mac_cfg);
4777 sp->promisc_flg = 1;
4778 DBG_PRINT(INFO_DBG, "%s: entered promiscuous mode\n",
4780 } else if (!(dev->flags & IFF_PROMISC) && (sp->promisc_flg)) {
4781 /* Remove the NIC from promiscuous mode */
4782 add = &bar0->mac_cfg;
4783 val64 = readq(&bar0->mac_cfg);
4784 val64 &= ~MAC_CFG_RMAC_PROM_ENABLE;
4786 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
4787 writel((u32) val64, add);
4788 writeq(RMAC_CFG_KEY(0x4C0D), &bar0->rmac_cfg_key);
4789 writel((u32) (val64 >> 32), (add + 4));
4791 if (vlan_tag_strip != 0) {
4792 val64 = readq(&bar0->rx_pa_cfg);
4793 val64 |= RX_PA_CFG_STRIP_VLAN_TAG;
4794 writeq(val64, &bar0->rx_pa_cfg);
4795 vlan_strip_flag = 1;
4798 val64 = readq(&bar0->mac_cfg);
4799 sp->promisc_flg = 0;
4800 DBG_PRINT(INFO_DBG, "%s: left promiscuous mode\n",
4804 /* Update individual M_CAST address list */
4805 if ((!sp->m_cast_flg) && dev->mc_count) {
4807 (MAX_ADDRS_SUPPORTED - MAC_MC_ADDR_START_OFFSET - 1)) {
4808 DBG_PRINT(ERR_DBG, "%s: No more Rx filters ",
4810 DBG_PRINT(ERR_DBG, "can be added, please enable ");
4811 DBG_PRINT(ERR_DBG, "ALL_MULTI instead\n");
4815 prev_cnt = sp->mc_addr_count;
4816 sp->mc_addr_count = dev->mc_count;
4818 /* Clear out the previous list of Mc in the H/W. */
4819 for (i = 0; i < prev_cnt; i++) {
4820 writeq(RMAC_ADDR_DATA0_MEM_ADDR(dis_addr),
4821 &bar0->rmac_addr_data0_mem);
4822 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
4823 &bar0->rmac_addr_data1_mem);
4824 val64 = RMAC_ADDR_CMD_MEM_WE |
4825 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4826 RMAC_ADDR_CMD_MEM_OFFSET
4827 (MAC_MC_ADDR_START_OFFSET + i);
4828 writeq(val64, &bar0->rmac_addr_cmd_mem);
4830 /* Wait for command completes */
4831 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4832 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4834 DBG_PRINT(ERR_DBG, "%s: Adding ",
4836 DBG_PRINT(ERR_DBG, "Multicasts failed\n");
4841 /* Create the new Rx filter list and update the same in H/W. */
4842 for (i = 0, mclist = dev->mc_list; i < dev->mc_count;
4843 i++, mclist = mclist->next) {
4844 memcpy(sp->usr_addrs[i].addr, mclist->dmi_addr,
4847 for (j = 0; j < ETH_ALEN; j++) {
4848 mac_addr |= mclist->dmi_addr[j];
4852 writeq(RMAC_ADDR_DATA0_MEM_ADDR(mac_addr),
4853 &bar0->rmac_addr_data0_mem);
4854 writeq(RMAC_ADDR_DATA1_MEM_MASK(0ULL),
4855 &bar0->rmac_addr_data1_mem);
4856 val64 = RMAC_ADDR_CMD_MEM_WE |
4857 RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4858 RMAC_ADDR_CMD_MEM_OFFSET
4859 (i + MAC_MC_ADDR_START_OFFSET);
4860 writeq(val64, &bar0->rmac_addr_cmd_mem);
4862 /* Wait for command completes */
4863 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4864 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4866 DBG_PRINT(ERR_DBG, "%s: Adding ",
4868 DBG_PRINT(ERR_DBG, "Multicasts failed\n");
4875 /* add unicast MAC address to CAM */
4876 static int do_s2io_add_unicast(struct s2io_nic *sp, u64 addr, int off)
4879 struct XENA_dev_config __iomem *bar0 = sp->bar0;
4881 writeq(RMAC_ADDR_DATA0_MEM_ADDR(addr),
4882 &bar0->rmac_addr_data0_mem);
4885 RMAC_ADDR_CMD_MEM_WE | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
4886 RMAC_ADDR_CMD_MEM_OFFSET(off);
4887 writeq(val64, &bar0->rmac_addr_cmd_mem);
4889 /* Wait till command completes */
4890 if (wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
4891 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING,
4893 DBG_PRINT(INFO_DBG, "add_mac_addr failed\n");
4900 * s2io_set_mac_addr driver entry point
4902 static int s2io_set_mac_addr(struct net_device *dev, void *p)
4904 struct sockaddr *addr = p;
4906 if (!is_valid_ether_addr(addr->sa_data))
4909 memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
4911 /* store the MAC address in CAM */
4912 return (do_s2io_prog_unicast(dev, dev->dev_addr));
4916 * do_s2io_prog_unicast - Programs the Xframe mac address
4917 * @dev : pointer to the device structure.
4918 * @addr: a uchar pointer to the new mac address which is to be set.
4919 * Description : This procedure will program the Xframe to receive
4920 * frames with new Mac Address
4921 * Return value: SUCCESS on success and an appropriate (-)ve integer
4922 * as defined in errno.h file on failure.
4924 static int do_s2io_prog_unicast(struct net_device *dev, u8 *addr)
4926 struct s2io_nic *sp = dev->priv;
4927 register u64 mac_addr = 0, perm_addr = 0;
4931 * Set the new MAC address as the new unicast filter and reflect this
4932 * change on the device address registered with the OS. It will be
4935 for (i = 0; i < ETH_ALEN; i++) {
4937 mac_addr |= addr[i];
4939 perm_addr |= sp->def_mac_addr[0].mac_addr[i];
4942 /* check if the dev_addr is different than perm_addr */
4943 if (mac_addr == perm_addr)
4946 /* Update the internal structure with this new mac address */
4947 do_s2io_copy_mac_addr(sp, 0, mac_addr);
4948 return (do_s2io_add_unicast(sp, mac_addr, 0));
4952 * s2io_ethtool_sset - Sets different link parameters.
4953 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
4954 * @info: pointer to the structure with parameters given by ethtool to set
4957 * The function sets different link parameters provided by the user onto
4963 static int s2io_ethtool_sset(struct net_device *dev,
4964 struct ethtool_cmd *info)
4966 struct s2io_nic *sp = dev->priv;
4967 if ((info->autoneg == AUTONEG_ENABLE) ||
4968 (info->speed != SPEED_10000) || (info->duplex != DUPLEX_FULL))
4971 s2io_close(sp->dev);
4979 * s2io_ethtol_gset - Return link specific information.
4980 * @sp : private member of the device structure, pointer to the
4981 * s2io_nic structure.
4982 * @info : pointer to the structure with parameters given by ethtool
4983 * to return link information.
4985 * Returns link specific information like speed, duplex etc.. to ethtool.
4987 * return 0 on success.
4990 static int s2io_ethtool_gset(struct net_device *dev, struct ethtool_cmd *info)
4992 struct s2io_nic *sp = dev->priv;
4993 info->supported = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
4994 info->advertising = (SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE);
4995 info->port = PORT_FIBRE;
4997 /* info->transceiver */
4998 info->transceiver = XCVR_EXTERNAL;
5000 if (netif_carrier_ok(sp->dev)) {
5001 info->speed = 10000;
5002 info->duplex = DUPLEX_FULL;
5008 info->autoneg = AUTONEG_DISABLE;
5013 * s2io_ethtool_gdrvinfo - Returns driver specific information.
5014 * @sp : private member of the device structure, which is a pointer to the
5015 * s2io_nic structure.
5016 * @info : pointer to the structure with parameters given by ethtool to
5017 * return driver information.
5019 * Returns driver specefic information like name, version etc.. to ethtool.
5024 static void s2io_ethtool_gdrvinfo(struct net_device *dev,
5025 struct ethtool_drvinfo *info)
5027 struct s2io_nic *sp = dev->priv;
5029 strncpy(info->driver, s2io_driver_name, sizeof(info->driver));
5030 strncpy(info->version, s2io_driver_version, sizeof(info->version));
5031 strncpy(info->fw_version, "", sizeof(info->fw_version));
5032 strncpy(info->bus_info, pci_name(sp->pdev), sizeof(info->bus_info));
5033 info->regdump_len = XENA_REG_SPACE;
5034 info->eedump_len = XENA_EEPROM_SPACE;
5038 * s2io_ethtool_gregs - dumps the entire space of Xfame into the buffer.
5039 * @sp: private member of the device structure, which is a pointer to the
5040 * s2io_nic structure.
5041 * @regs : pointer to the structure with parameters given by ethtool for
5042 * dumping the registers.
5043 * @reg_space: The input argumnet into which all the registers are dumped.
5045 * Dumps the entire register space of xFrame NIC into the user given
5051 static void s2io_ethtool_gregs(struct net_device *dev,
5052 struct ethtool_regs *regs, void *space)
5056 u8 *reg_space = (u8 *) space;
5057 struct s2io_nic *sp = dev->priv;
5059 regs->len = XENA_REG_SPACE;
5060 regs->version = sp->pdev->subsystem_device;
5062 for (i = 0; i < regs->len; i += 8) {
5063 reg = readq(sp->bar0 + i);
5064 memcpy((reg_space + i), ®, 8);
5069 * s2io_phy_id - timer function that alternates adapter LED.
5070 * @data : address of the private member of the device structure, which
5071 * is a pointer to the s2io_nic structure, provided as an u32.
5072 * Description: This is actually the timer function that alternates the
5073 * adapter LED bit of the adapter control bit to set/reset every time on
5074 * invocation. The timer is set for 1/2 a second, hence tha NIC blinks
5075 * once every second.
5077 static void s2io_phy_id(unsigned long data)
5079 struct s2io_nic *sp = (struct s2io_nic *) data;
5080 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5084 subid = sp->pdev->subsystem_device;
5085 if ((sp->device_type == XFRAME_II_DEVICE) ||
5086 ((subid & 0xFF) >= 0x07)) {
5087 val64 = readq(&bar0->gpio_control);
5088 val64 ^= GPIO_CTRL_GPIO_0;
5089 writeq(val64, &bar0->gpio_control);
5091 val64 = readq(&bar0->adapter_control);
5092 val64 ^= ADAPTER_LED_ON;
5093 writeq(val64, &bar0->adapter_control);
5096 mod_timer(&sp->id_timer, jiffies + HZ / 2);
5100 * s2io_ethtool_idnic - To physically identify the nic on the system.
5101 * @sp : private member of the device structure, which is a pointer to the
5102 * s2io_nic structure.
5103 * @id : pointer to the structure with identification parameters given by
5105 * Description: Used to physically identify the NIC on the system.
5106 * The Link LED will blink for a time specified by the user for
5108 * NOTE: The Link has to be Up to be able to blink the LED. Hence
5109 * identification is possible only if it's link is up.
5111 * int , returns 0 on success
5114 static int s2io_ethtool_idnic(struct net_device *dev, u32 data)
5116 u64 val64 = 0, last_gpio_ctrl_val;
5117 struct s2io_nic *sp = dev->priv;
5118 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5121 subid = sp->pdev->subsystem_device;
5122 last_gpio_ctrl_val = readq(&bar0->gpio_control);
5123 if ((sp->device_type == XFRAME_I_DEVICE) &&
5124 ((subid & 0xFF) < 0x07)) {
5125 val64 = readq(&bar0->adapter_control);
5126 if (!(val64 & ADAPTER_CNTL_EN)) {
5128 "Adapter Link down, cannot blink LED\n");
5132 if (sp->id_timer.function == NULL) {
5133 init_timer(&sp->id_timer);
5134 sp->id_timer.function = s2io_phy_id;
5135 sp->id_timer.data = (unsigned long) sp;
5137 mod_timer(&sp->id_timer, jiffies);
5139 msleep_interruptible(data * HZ);
5141 msleep_interruptible(MAX_FLICKER_TIME);
5142 del_timer_sync(&sp->id_timer);
5144 if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid)) {
5145 writeq(last_gpio_ctrl_val, &bar0->gpio_control);
5146 last_gpio_ctrl_val = readq(&bar0->gpio_control);
5152 static void s2io_ethtool_gringparam(struct net_device *dev,
5153 struct ethtool_ringparam *ering)
5155 struct s2io_nic *sp = dev->priv;
5156 int i,tx_desc_count=0,rx_desc_count=0;
5158 if (sp->rxd_mode == RXD_MODE_1)
5159 ering->rx_max_pending = MAX_RX_DESC_1;
5160 else if (sp->rxd_mode == RXD_MODE_3B)
5161 ering->rx_max_pending = MAX_RX_DESC_2;
5163 ering->tx_max_pending = MAX_TX_DESC;
5164 for (i = 0 ; i < sp->config.tx_fifo_num ; i++)
5165 tx_desc_count += sp->config.tx_cfg[i].fifo_len;
5167 DBG_PRINT(INFO_DBG,"\nmax txds : %d\n",sp->config.max_txds);
5168 ering->tx_pending = tx_desc_count;
5170 for (i = 0 ; i < sp->config.rx_ring_num ; i++)
5171 rx_desc_count += sp->config.rx_cfg[i].num_rxd;
5173 ering->rx_pending = rx_desc_count;
5175 ering->rx_mini_max_pending = 0;
5176 ering->rx_mini_pending = 0;
5177 if(sp->rxd_mode == RXD_MODE_1)
5178 ering->rx_jumbo_max_pending = MAX_RX_DESC_1;
5179 else if (sp->rxd_mode == RXD_MODE_3B)
5180 ering->rx_jumbo_max_pending = MAX_RX_DESC_2;
5181 ering->rx_jumbo_pending = rx_desc_count;
5185 * s2io_ethtool_getpause_data -Pause frame frame generation and reception.
5186 * @sp : private member of the device structure, which is a pointer to the
5187 * s2io_nic structure.
5188 * @ep : pointer to the structure with pause parameters given by ethtool.
5190 * Returns the Pause frame generation and reception capability of the NIC.
5194 static void s2io_ethtool_getpause_data(struct net_device *dev,
5195 struct ethtool_pauseparam *ep)
5198 struct s2io_nic *sp = dev->priv;
5199 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5201 val64 = readq(&bar0->rmac_pause_cfg);
5202 if (val64 & RMAC_PAUSE_GEN_ENABLE)
5203 ep->tx_pause = TRUE;
5204 if (val64 & RMAC_PAUSE_RX_ENABLE)
5205 ep->rx_pause = TRUE;
5206 ep->autoneg = FALSE;
5210 * s2io_ethtool_setpause_data - set/reset pause frame generation.
5211 * @sp : private member of the device structure, which is a pointer to the
5212 * s2io_nic structure.
5213 * @ep : pointer to the structure with pause parameters given by ethtool.
5215 * It can be used to set or reset Pause frame generation or reception
5216 * support of the NIC.
5218 * int, returns 0 on Success
5221 static int s2io_ethtool_setpause_data(struct net_device *dev,
5222 struct ethtool_pauseparam *ep)
5225 struct s2io_nic *sp = dev->priv;
5226 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5228 val64 = readq(&bar0->rmac_pause_cfg);
5230 val64 |= RMAC_PAUSE_GEN_ENABLE;
5232 val64 &= ~RMAC_PAUSE_GEN_ENABLE;
5234 val64 |= RMAC_PAUSE_RX_ENABLE;
5236 val64 &= ~RMAC_PAUSE_RX_ENABLE;
5237 writeq(val64, &bar0->rmac_pause_cfg);
5242 * read_eeprom - reads 4 bytes of data from user given offset.
5243 * @sp : private member of the device structure, which is a pointer to the
5244 * s2io_nic structure.
5245 * @off : offset at which the data must be written
5246 * @data : Its an output parameter where the data read at the given
5249 * Will read 4 bytes of data from the user given offset and return the
5251 * NOTE: Will allow to read only part of the EEPROM visible through the
5254 * -1 on failure and 0 on success.
5257 #define S2IO_DEV_ID 5
5258 static int read_eeprom(struct s2io_nic * sp, int off, u64 * data)
5263 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5265 if (sp->device_type == XFRAME_I_DEVICE) {
5266 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) | I2C_CONTROL_ADDR(off) |
5267 I2C_CONTROL_BYTE_CNT(0x3) | I2C_CONTROL_READ |
5268 I2C_CONTROL_CNTL_START;
5269 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5271 while (exit_cnt < 5) {
5272 val64 = readq(&bar0->i2c_control);
5273 if (I2C_CONTROL_CNTL_END(val64)) {
5274 *data = I2C_CONTROL_GET_DATA(val64);
5283 if (sp->device_type == XFRAME_II_DEVICE) {
5284 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5285 SPI_CONTROL_BYTECNT(0x3) |
5286 SPI_CONTROL_CMD(0x3) | SPI_CONTROL_ADDR(off);
5287 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5288 val64 |= SPI_CONTROL_REQ;
5289 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5290 while (exit_cnt < 5) {
5291 val64 = readq(&bar0->spi_control);
5292 if (val64 & SPI_CONTROL_NACK) {
5295 } else if (val64 & SPI_CONTROL_DONE) {
5296 *data = readq(&bar0->spi_data);
5309 * write_eeprom - actually writes the relevant part of the data value.
5310 * @sp : private member of the device structure, which is a pointer to the
5311 * s2io_nic structure.
5312 * @off : offset at which the data must be written
5313 * @data : The data that is to be written
5314 * @cnt : Number of bytes of the data that are actually to be written into
5315 * the Eeprom. (max of 3)
5317 * Actually writes the relevant part of the data value into the Eeprom
5318 * through the I2C bus.
5320 * 0 on success, -1 on failure.
5323 static int write_eeprom(struct s2io_nic * sp, int off, u64 data, int cnt)
5325 int exit_cnt = 0, ret = -1;
5327 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5329 if (sp->device_type == XFRAME_I_DEVICE) {
5330 val64 = I2C_CONTROL_DEV_ID(S2IO_DEV_ID) | I2C_CONTROL_ADDR(off) |
5331 I2C_CONTROL_BYTE_CNT(cnt) | I2C_CONTROL_SET_DATA((u32)data) |
5332 I2C_CONTROL_CNTL_START;
5333 SPECIAL_REG_WRITE(val64, &bar0->i2c_control, LF);
5335 while (exit_cnt < 5) {
5336 val64 = readq(&bar0->i2c_control);
5337 if (I2C_CONTROL_CNTL_END(val64)) {
5338 if (!(val64 & I2C_CONTROL_NACK))
5347 if (sp->device_type == XFRAME_II_DEVICE) {
5348 int write_cnt = (cnt == 8) ? 0 : cnt;
5349 writeq(SPI_DATA_WRITE(data,(cnt<<3)), &bar0->spi_data);
5351 val64 = SPI_CONTROL_KEY(0x9) | SPI_CONTROL_SEL1 |
5352 SPI_CONTROL_BYTECNT(write_cnt) |
5353 SPI_CONTROL_CMD(0x2) | SPI_CONTROL_ADDR(off);
5354 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5355 val64 |= SPI_CONTROL_REQ;
5356 SPECIAL_REG_WRITE(val64, &bar0->spi_control, LF);
5357 while (exit_cnt < 5) {
5358 val64 = readq(&bar0->spi_control);
5359 if (val64 & SPI_CONTROL_NACK) {
5362 } else if (val64 & SPI_CONTROL_DONE) {
5372 static void s2io_vpd_read(struct s2io_nic *nic)
5376 int i=0, cnt, fail = 0;
5377 int vpd_addr = 0x80;
5379 if (nic->device_type == XFRAME_II_DEVICE) {
5380 strcpy(nic->product_name, "Xframe II 10GbE network adapter");
5384 strcpy(nic->product_name, "Xframe I 10GbE network adapter");
5387 strcpy(nic->serial_num, "NOT AVAILABLE");
5389 vpd_data = kmalloc(256, GFP_KERNEL);
5391 nic->mac_control.stats_info->sw_stat.mem_alloc_fail_cnt++;
5394 nic->mac_control.stats_info->sw_stat.mem_allocated += 256;
5396 for (i = 0; i < 256; i +=4 ) {
5397 pci_write_config_byte(nic->pdev, (vpd_addr + 2), i);
5398 pci_read_config_byte(nic->pdev, (vpd_addr + 2), &data);
5399 pci_write_config_byte(nic->pdev, (vpd_addr + 3), 0);
5400 for (cnt = 0; cnt <5; cnt++) {
5402 pci_read_config_byte(nic->pdev, (vpd_addr + 3), &data);
5407 DBG_PRINT(ERR_DBG, "Read of VPD data failed\n");
5411 pci_read_config_dword(nic->pdev, (vpd_addr + 4),
5412 (u32 *)&vpd_data[i]);
5416 /* read serial number of adapter */
5417 for (cnt = 0; cnt < 256; cnt++) {
5418 if ((vpd_data[cnt] == 'S') &&
5419 (vpd_data[cnt+1] == 'N') &&
5420 (vpd_data[cnt+2] < VPD_STRING_LEN)) {
5421 memset(nic->serial_num, 0, VPD_STRING_LEN);
5422 memcpy(nic->serial_num, &vpd_data[cnt + 3],
5429 if ((!fail) && (vpd_data[1] < VPD_STRING_LEN)) {
5430 memset(nic->product_name, 0, vpd_data[1]);
5431 memcpy(nic->product_name, &vpd_data[3], vpd_data[1]);
5434 nic->mac_control.stats_info->sw_stat.mem_freed += 256;
5438 * s2io_ethtool_geeprom - reads the value stored in the Eeprom.
5439 * @sp : private member of the device structure, which is a pointer to the * s2io_nic structure.
5440 * @eeprom : pointer to the user level structure provided by ethtool,
5441 * containing all relevant information.
5442 * @data_buf : user defined value to be written into Eeprom.
5443 * Description: Reads the values stored in the Eeprom at given offset
5444 * for a given length. Stores these values int the input argument data
5445 * buffer 'data_buf' and returns these to the caller (ethtool.)
5450 static int s2io_ethtool_geeprom(struct net_device *dev,
5451 struct ethtool_eeprom *eeprom, u8 * data_buf)
5455 struct s2io_nic *sp = dev->priv;
5457 eeprom->magic = sp->pdev->vendor | (sp->pdev->device << 16);
5459 if ((eeprom->offset + eeprom->len) > (XENA_EEPROM_SPACE))
5460 eeprom->len = XENA_EEPROM_SPACE - eeprom->offset;
5462 for (i = 0; i < eeprom->len; i += 4) {
5463 if (read_eeprom(sp, (eeprom->offset + i), &data)) {
5464 DBG_PRINT(ERR_DBG, "Read of EEPROM failed\n");
5468 memcpy((data_buf + i), &valid, 4);
5474 * s2io_ethtool_seeprom - tries to write the user provided value in Eeprom
5475 * @sp : private member of the device structure, which is a pointer to the
5476 * s2io_nic structure.
5477 * @eeprom : pointer to the user level structure provided by ethtool,
5478 * containing all relevant information.
5479 * @data_buf ; user defined value to be written into Eeprom.
5481 * Tries to write the user provided value in the Eeprom, at the offset
5482 * given by the user.
5484 * 0 on success, -EFAULT on failure.
5487 static int s2io_ethtool_seeprom(struct net_device *dev,
5488 struct ethtool_eeprom *eeprom,
5491 int len = eeprom->len, cnt = 0;
5492 u64 valid = 0, data;
5493 struct s2io_nic *sp = dev->priv;
5495 if (eeprom->magic != (sp->pdev->vendor | (sp->pdev->device << 16))) {
5497 "ETHTOOL_WRITE_EEPROM Err: Magic value ");
5498 DBG_PRINT(ERR_DBG, "is wrong, Its not 0x%x\n",
5504 data = (u32) data_buf[cnt] & 0x000000FF;
5506 valid = (u32) (data << 24);
5510 if (write_eeprom(sp, (eeprom->offset + cnt), valid, 0)) {
5512 "ETHTOOL_WRITE_EEPROM Err: Cannot ");
5514 "write into the specified offset\n");
5525 * s2io_register_test - reads and writes into all clock domains.
5526 * @sp : private member of the device structure, which is a pointer to the
5527 * s2io_nic structure.
5528 * @data : variable that returns the result of each of the test conducted b
5531 * Read and write into all clock domains. The NIC has 3 clock domains,
5532 * see that registers in all the three regions are accessible.
5537 static int s2io_register_test(struct s2io_nic * sp, uint64_t * data)
5539 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5540 u64 val64 = 0, exp_val;
5543 val64 = readq(&bar0->pif_rd_swapper_fb);
5544 if (val64 != 0x123456789abcdefULL) {
5546 DBG_PRINT(INFO_DBG, "Read Test level 1 fails\n");
5549 val64 = readq(&bar0->rmac_pause_cfg);
5550 if (val64 != 0xc000ffff00000000ULL) {
5552 DBG_PRINT(INFO_DBG, "Read Test level 2 fails\n");
5555 val64 = readq(&bar0->rx_queue_cfg);
5556 if (sp->device_type == XFRAME_II_DEVICE)
5557 exp_val = 0x0404040404040404ULL;
5559 exp_val = 0x0808080808080808ULL;
5560 if (val64 != exp_val) {
5562 DBG_PRINT(INFO_DBG, "Read Test level 3 fails\n");
5565 val64 = readq(&bar0->xgxs_efifo_cfg);
5566 if (val64 != 0x000000001923141EULL) {
5568 DBG_PRINT(INFO_DBG, "Read Test level 4 fails\n");
5571 val64 = 0x5A5A5A5A5A5A5A5AULL;
5572 writeq(val64, &bar0->xmsi_data);
5573 val64 = readq(&bar0->xmsi_data);
5574 if (val64 != 0x5A5A5A5A5A5A5A5AULL) {
5576 DBG_PRINT(ERR_DBG, "Write Test level 1 fails\n");
5579 val64 = 0xA5A5A5A5A5A5A5A5ULL;
5580 writeq(val64, &bar0->xmsi_data);
5581 val64 = readq(&bar0->xmsi_data);
5582 if (val64 != 0xA5A5A5A5A5A5A5A5ULL) {
5584 DBG_PRINT(ERR_DBG, "Write Test level 2 fails\n");
5592 * s2io_eeprom_test - to verify that EEprom in the xena can be programmed.
5593 * @sp : private member of the device structure, which is a pointer to the
5594 * s2io_nic structure.
5595 * @data:variable that returns the result of each of the test conducted by
5598 * Verify that EEPROM in the xena can be programmed using I2C_CONTROL
5604 static int s2io_eeprom_test(struct s2io_nic * sp, uint64_t * data)
5607 u64 ret_data, org_4F0, org_7F0;
5608 u8 saved_4F0 = 0, saved_7F0 = 0;
5609 struct net_device *dev = sp->dev;
5611 /* Test Write Error at offset 0 */
5612 /* Note that SPI interface allows write access to all areas
5613 * of EEPROM. Hence doing all negative testing only for Xframe I.
5615 if (sp->device_type == XFRAME_I_DEVICE)
5616 if (!write_eeprom(sp, 0, 0, 3))
5619 /* Save current values at offsets 0x4F0 and 0x7F0 */
5620 if (!read_eeprom(sp, 0x4F0, &org_4F0))
5622 if (!read_eeprom(sp, 0x7F0, &org_7F0))
5625 /* Test Write at offset 4f0 */
5626 if (write_eeprom(sp, 0x4F0, 0x012345, 3))
5628 if (read_eeprom(sp, 0x4F0, &ret_data))
5631 if (ret_data != 0x012345) {
5632 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x4F0. "
5633 "Data written %llx Data read %llx\n",
5634 dev->name, (unsigned long long)0x12345,
5635 (unsigned long long)ret_data);
5639 /* Reset the EEPROM data go FFFF */
5640 write_eeprom(sp, 0x4F0, 0xFFFFFF, 3);
5642 /* Test Write Request Error at offset 0x7c */
5643 if (sp->device_type == XFRAME_I_DEVICE)
5644 if (!write_eeprom(sp, 0x07C, 0, 3))
5647 /* Test Write Request at offset 0x7f0 */
5648 if (write_eeprom(sp, 0x7F0, 0x012345, 3))
5650 if (read_eeprom(sp, 0x7F0, &ret_data))
5653 if (ret_data != 0x012345) {
5654 DBG_PRINT(ERR_DBG, "%s: eeprom test error at offset 0x7F0. "
5655 "Data written %llx Data read %llx\n",
5656 dev->name, (unsigned long long)0x12345,
5657 (unsigned long long)ret_data);
5661 /* Reset the EEPROM data go FFFF */
5662 write_eeprom(sp, 0x7F0, 0xFFFFFF, 3);
5664 if (sp->device_type == XFRAME_I_DEVICE) {
5665 /* Test Write Error at offset 0x80 */
5666 if (!write_eeprom(sp, 0x080, 0, 3))
5669 /* Test Write Error at offset 0xfc */
5670 if (!write_eeprom(sp, 0x0FC, 0, 3))
5673 /* Test Write Error at offset 0x100 */
5674 if (!write_eeprom(sp, 0x100, 0, 3))
5677 /* Test Write Error at offset 4ec */
5678 if (!write_eeprom(sp, 0x4EC, 0, 3))
5682 /* Restore values at offsets 0x4F0 and 0x7F0 */
5684 write_eeprom(sp, 0x4F0, org_4F0, 3);
5686 write_eeprom(sp, 0x7F0, org_7F0, 3);
5693 * s2io_bist_test - invokes the MemBist test of the card .
5694 * @sp : private member of the device structure, which is a pointer to the
5695 * s2io_nic structure.
5696 * @data:variable that returns the result of each of the test conducted by
5699 * This invokes the MemBist test of the card. We give around
5700 * 2 secs time for the Test to complete. If it's still not complete
5701 * within this peiod, we consider that the test failed.
5703 * 0 on success and -1 on failure.
5706 static int s2io_bist_test(struct s2io_nic * sp, uint64_t * data)
5709 int cnt = 0, ret = -1;
5711 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
5712 bist |= PCI_BIST_START;
5713 pci_write_config_word(sp->pdev, PCI_BIST, bist);
5716 pci_read_config_byte(sp->pdev, PCI_BIST, &bist);
5717 if (!(bist & PCI_BIST_START)) {
5718 *data = (bist & PCI_BIST_CODE_MASK);
5730 * s2io-link_test - verifies the link state of the nic
5731 * @sp ; private member of the device structure, which is a pointer to the
5732 * s2io_nic structure.
5733 * @data: variable that returns the result of each of the test conducted by
5736 * The function verifies the link state of the NIC and updates the input
5737 * argument 'data' appropriately.
5742 static int s2io_link_test(struct s2io_nic * sp, uint64_t * data)
5744 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5747 val64 = readq(&bar0->adapter_status);
5748 if(!(LINK_IS_UP(val64)))
5757 * s2io_rldram_test - offline test for access to the RldRam chip on the NIC
5758 * @sp - private member of the device structure, which is a pointer to the
5759 * s2io_nic structure.
5760 * @data - variable that returns the result of each of the test
5761 * conducted by the driver.
5763 * This is one of the offline test that tests the read and write
5764 * access to the RldRam chip on the NIC.
5769 static int s2io_rldram_test(struct s2io_nic * sp, uint64_t * data)
5771 struct XENA_dev_config __iomem *bar0 = sp->bar0;
5773 int cnt, iteration = 0, test_fail = 0;
5775 val64 = readq(&bar0->adapter_control);
5776 val64 &= ~ADAPTER_ECC_EN;
5777 writeq(val64, &bar0->adapter_control);
5779 val64 = readq(&bar0->mc_rldram_test_ctrl);
5780 val64 |= MC_RLDRAM_TEST_MODE;
5781 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
5783 val64 = readq(&bar0->mc_rldram_mrs);
5784 val64 |= MC_RLDRAM_QUEUE_SIZE_ENABLE;
5785 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
5787 val64 |= MC_RLDRAM_MRS_ENABLE;
5788 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_mrs, UF);
5790 while (iteration < 2) {
5791 val64 = 0x55555555aaaa0000ULL;
5792 if (iteration == 1) {
5793 val64 ^= 0xFFFFFFFFFFFF0000ULL;
5795 writeq(val64, &bar0->mc_rldram_test_d0);
5797 val64 = 0xaaaa5a5555550000ULL;
5798 if (iteration == 1) {
5799 val64 ^= 0xFFFFFFFFFFFF0000ULL;
5801 writeq(val64, &bar0->mc_rldram_test_d1);
5803 val64 = 0x55aaaaaaaa5a0000ULL;
5804 if (iteration == 1) {
5805 val64 ^= 0xFFFFFFFFFFFF0000ULL;
5807 writeq(val64, &bar0->mc_rldram_test_d2);
5809 val64 = (u64) (0x0000003ffffe0100ULL);
5810 writeq(val64, &bar0->mc_rldram_test_add);
5812 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_WRITE |
5814 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
5816 for (cnt = 0; cnt < 5; cnt++) {
5817 val64 = readq(&bar0->mc_rldram_test_ctrl);
5818 if (val64 & MC_RLDRAM_TEST_DONE)
5826 val64 = MC_RLDRAM_TEST_MODE | MC_RLDRAM_TEST_GO;
5827 SPECIAL_REG_WRITE(val64, &bar0->mc_rldram_test_ctrl, LF);
5829 for (cnt = 0; cnt < 5; cnt++) {
5830 val64 = readq(&bar0->mc_rldram_test_ctrl);
5831 if (val64 & MC_RLDRAM_TEST_DONE)
5839 val64 = readq(&bar0->mc_rldram_test_ctrl);
5840 if (!(val64 & MC_RLDRAM_TEST_PASS))
5848 /* Bring the adapter out of test mode */
5849 SPECIAL_REG_WRITE(0, &bar0->mc_rldram_test_ctrl, LF);
5855 * s2io_ethtool_test - conducts 6 tsets to determine the health of card.
5856 * @sp : private member of the device structure, which is a pointer to the
5857 * s2io_nic structure.
5858 * @ethtest : pointer to a ethtool command specific structure that will be
5859 * returned to the user.
5860 * @data : variable that returns the result of each of the test
5861 * conducted by the driver.
5863 * This function conducts 6 tests ( 4 offline and 2 online) to determine
5864 * the health of the card.
5869 static void s2io_ethtool_test(struct net_device *dev,
5870 struct ethtool_test *ethtest,
5873 struct s2io_nic *sp = dev->priv;
5874 int orig_state = netif_running(sp->dev);
5876 if (ethtest->flags == ETH_TEST_FL_OFFLINE) {
5877 /* Offline Tests. */
5879 s2io_close(sp->dev);
5881 if (s2io_register_test(sp, &data[0]))
5882 ethtest->flags |= ETH_TEST_FL_FAILED;
5886 if (s2io_rldram_test(sp, &data[3]))
5887 ethtest->flags |= ETH_TEST_FL_FAILED;
5891 if (s2io_eeprom_test(sp, &data[1]))
5892 ethtest->flags |= ETH_TEST_FL_FAILED;
5894 if (s2io_bist_test(sp, &data[4]))
5895 ethtest->flags |= ETH_TEST_FL_FAILED;
5905 "%s: is not up, cannot run test\n",
5914 if (s2io_link_test(sp, &data[2]))
5915 ethtest->flags |= ETH_TEST_FL_FAILED;
5924 static void s2io_get_ethtool_stats(struct net_device *dev,
5925 struct ethtool_stats *estats,
5929 struct s2io_nic *sp = dev->priv;
5930 struct stat_block *stat_info = sp->mac_control.stats_info;
5932 s2io_updt_stats(sp);
5934 (u64)le32_to_cpu(stat_info->tmac_frms_oflow) << 32 |
5935 le32_to_cpu(stat_info->tmac_frms);
5937 (u64)le32_to_cpu(stat_info->tmac_data_octets_oflow) << 32 |
5938 le32_to_cpu(stat_info->tmac_data_octets);
5939 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms);
5941 (u64)le32_to_cpu(stat_info->tmac_mcst_frms_oflow) << 32 |
5942 le32_to_cpu(stat_info->tmac_mcst_frms);
5944 (u64)le32_to_cpu(stat_info->tmac_bcst_frms_oflow) << 32 |
5945 le32_to_cpu(stat_info->tmac_bcst_frms);
5946 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_pause_ctrl_frms);
5948 (u64)le32_to_cpu(stat_info->tmac_ttl_octets_oflow) << 32 |
5949 le32_to_cpu(stat_info->tmac_ttl_octets);
5951 (u64)le32_to_cpu(stat_info->tmac_ucst_frms_oflow) << 32 |
5952 le32_to_cpu(stat_info->tmac_ucst_frms);
5954 (u64)le32_to_cpu(stat_info->tmac_nucst_frms_oflow) << 32 |
5955 le32_to_cpu(stat_info->tmac_nucst_frms);
5957 (u64)le32_to_cpu(stat_info->tmac_any_err_frms_oflow) << 32 |
5958 le32_to_cpu(stat_info->tmac_any_err_frms);
5959 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_ttl_less_fb_octets);
5960 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_vld_ip_octets);
5962 (u64)le32_to_cpu(stat_info->tmac_vld_ip_oflow) << 32 |
5963 le32_to_cpu(stat_info->tmac_vld_ip);
5965 (u64)le32_to_cpu(stat_info->tmac_drop_ip_oflow) << 32 |
5966 le32_to_cpu(stat_info->tmac_drop_ip);
5968 (u64)le32_to_cpu(stat_info->tmac_icmp_oflow) << 32 |
5969 le32_to_cpu(stat_info->tmac_icmp);
5971 (u64)le32_to_cpu(stat_info->tmac_rst_tcp_oflow) << 32 |
5972 le32_to_cpu(stat_info->tmac_rst_tcp);
5973 tmp_stats[i++] = le64_to_cpu(stat_info->tmac_tcp);
5974 tmp_stats[i++] = (u64)le32_to_cpu(stat_info->tmac_udp_oflow) << 32 |
5975 le32_to_cpu(stat_info->tmac_udp);
5977 (u64)le32_to_cpu(stat_info->rmac_vld_frms_oflow) << 32 |
5978 le32_to_cpu(stat_info->rmac_vld_frms);
5980 (u64)le32_to_cpu(stat_info->rmac_data_octets_oflow) << 32 |
5981 le32_to_cpu(stat_info->rmac_data_octets);
5982 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_fcs_err_frms);
5983 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_drop_frms);
5985 (u64)le32_to_cpu(stat_info->rmac_vld_mcst_frms_oflow) << 32 |
5986 le32_to_cpu(stat_info->rmac_vld_mcst_frms);
5988 (u64)le32_to_cpu(stat_info->rmac_vld_bcst_frms_oflow) << 32 |
5989 le32_to_cpu(stat_info->rmac_vld_bcst_frms);
5990 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_in_rng_len_err_frms);
5991 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_out_rng_len_err_frms);
5992 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_long_frms);
5993 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_pause_ctrl_frms);
5994 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_unsup_ctrl_frms);
5996 (u64)le32_to_cpu(stat_info->rmac_ttl_octets_oflow) << 32 |
5997 le32_to_cpu(stat_info->rmac_ttl_octets);
5999 (u64)le32_to_cpu(stat_info->rmac_accepted_ucst_frms_oflow)
6000 << 32 | le32_to_cpu(stat_info->rmac_accepted_ucst_frms);
6002 (u64)le32_to_cpu(stat_info->rmac_accepted_nucst_frms_oflow)
6003 << 32 | le32_to_cpu(stat_info->rmac_accepted_nucst_frms);
6005 (u64)le32_to_cpu(stat_info->rmac_discarded_frms_oflow) << 32 |
6006 le32_to_cpu(stat_info->rmac_discarded_frms);
6008 (u64)le32_to_cpu(stat_info->rmac_drop_events_oflow)
6009 << 32 | le32_to_cpu(stat_info->rmac_drop_events);
6010 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_less_fb_octets);
6011 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_frms);
6013 (u64)le32_to_cpu(stat_info->rmac_usized_frms_oflow) << 32 |
6014 le32_to_cpu(stat_info->rmac_usized_frms);
6016 (u64)le32_to_cpu(stat_info->rmac_osized_frms_oflow) << 32 |
6017 le32_to_cpu(stat_info->rmac_osized_frms);
6019 (u64)le32_to_cpu(stat_info->rmac_frag_frms_oflow) << 32 |
6020 le32_to_cpu(stat_info->rmac_frag_frms);
6022 (u64)le32_to_cpu(stat_info->rmac_jabber_frms_oflow) << 32 |
6023 le32_to_cpu(stat_info->rmac_jabber_frms);
6024 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_64_frms);
6025 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_65_127_frms);
6026 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_128_255_frms);
6027 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_256_511_frms);
6028 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_512_1023_frms);
6029 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_1024_1518_frms);
6031 (u64)le32_to_cpu(stat_info->rmac_ip_oflow) << 32 |
6032 le32_to_cpu(stat_info->rmac_ip);
6033 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ip_octets);
6034 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_hdr_err_ip);
6036 (u64)le32_to_cpu(stat_info->rmac_drop_ip_oflow) << 32 |
6037 le32_to_cpu(stat_info->rmac_drop_ip);
6039 (u64)le32_to_cpu(stat_info->rmac_icmp_oflow) << 32 |
6040 le32_to_cpu(stat_info->rmac_icmp);
6041 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_tcp);
6043 (u64)le32_to_cpu(stat_info->rmac_udp_oflow) << 32 |
6044 le32_to_cpu(stat_info->rmac_udp);
6046 (u64)le32_to_cpu(stat_info->rmac_err_drp_udp_oflow) << 32 |
6047 le32_to_cpu(stat_info->rmac_err_drp_udp);
6048 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_err_sym);
6049 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q0);
6050 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q1);
6051 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q2);
6052 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q3);
6053 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q4);
6054 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q5);
6055 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q6);
6056 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_frms_q7);
6057 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q0);
6058 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q1);
6059 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q2);
6060 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q3);
6061 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q4);
6062 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q5);
6063 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q6);
6064 tmp_stats[i++] = le16_to_cpu(stat_info->rmac_full_q7);
6066 (u64)le32_to_cpu(stat_info->rmac_pause_cnt_oflow) << 32 |
6067 le32_to_cpu(stat_info->rmac_pause_cnt);
6068 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_data_err_cnt);
6069 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_xgmii_ctrl_err_cnt);
6071 (u64)le32_to_cpu(stat_info->rmac_accepted_ip_oflow) << 32 |
6072 le32_to_cpu(stat_info->rmac_accepted_ip);
6073 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp);
6074 tmp_stats[i++] = le32_to_cpu(stat_info->rd_req_cnt);
6075 tmp_stats[i++] = le32_to_cpu(stat_info->new_rd_req_cnt);
6076 tmp_stats[i++] = le32_to_cpu(stat_info->new_rd_req_rtry_cnt);
6077 tmp_stats[i++] = le32_to_cpu(stat_info->rd_rtry_cnt);
6078 tmp_stats[i++] = le32_to_cpu(stat_info->wr_rtry_rd_ack_cnt);
6079 tmp_stats[i++] = le32_to_cpu(stat_info->wr_req_cnt);
6080 tmp_stats[i++] = le32_to_cpu(stat_info->new_wr_req_cnt);
6081 tmp_stats[i++] = le32_to_cpu(stat_info->new_wr_req_rtry_cnt);
6082 tmp_stats[i++] = le32_to_cpu(stat_info->wr_rtry_cnt);
6083 tmp_stats[i++] = le32_to_cpu(stat_info->wr_disc_cnt);
6084 tmp_stats[i++] = le32_to_cpu(stat_info->rd_rtry_wr_ack_cnt);
6085 tmp_stats[i++] = le32_to_cpu(stat_info->txp_wr_cnt);
6086 tmp_stats[i++] = le32_to_cpu(stat_info->txd_rd_cnt);
6087 tmp_stats[i++] = le32_to_cpu(stat_info->txd_wr_cnt);
6088 tmp_stats[i++] = le32_to_cpu(stat_info->rxd_rd_cnt);
6089 tmp_stats[i++] = le32_to_cpu(stat_info->rxd_wr_cnt);
6090 tmp_stats[i++] = le32_to_cpu(stat_info->txf_rd_cnt);
6091 tmp_stats[i++] = le32_to_cpu(stat_info->rxf_wr_cnt);
6093 /* Enhanced statistics exist only for Hercules */
6094 if(sp->device_type == XFRAME_II_DEVICE) {
6096 le64_to_cpu(stat_info->rmac_ttl_1519_4095_frms);
6098 le64_to_cpu(stat_info->rmac_ttl_4096_8191_frms);
6100 le64_to_cpu(stat_info->rmac_ttl_8192_max_frms);
6101 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ttl_gt_max_frms);
6102 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_osized_alt_frms);
6103 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_jabber_alt_frms);
6104 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_gt_max_alt_frms);
6105 tmp_stats[i++] = le64_to_cpu(stat_info->rmac_vlan_frms);
6106 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_len_discard);
6107 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_fcs_discard);
6108 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pf_discard);
6109 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_da_discard);
6110 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_red_discard);
6111 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_rts_discard);
6112 tmp_stats[i++] = le32_to_cpu(stat_info->rmac_ingm_full_discard);
6113 tmp_stats[i++] = le32_to_cpu(stat_info->link_fault_cnt);
6117 tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs;
6118 tmp_stats[i++] = stat_info->sw_stat.double_ecc_errs;
6119 tmp_stats[i++] = stat_info->sw_stat.parity_err_cnt;
6120 tmp_stats[i++] = stat_info->sw_stat.serious_err_cnt;
6121 tmp_stats[i++] = stat_info->sw_stat.soft_reset_cnt;
6122 tmp_stats[i++] = stat_info->sw_stat.fifo_full_cnt;
6123 for (k = 0; k < MAX_RX_RINGS; k++)
6124 tmp_stats[i++] = stat_info->sw_stat.ring_full_cnt[k];
6125 tmp_stats[i++] = stat_info->xpak_stat.alarm_transceiver_temp_high;
6126 tmp_stats[i++] = stat_info->xpak_stat.alarm_transceiver_temp_low;
6127 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_bias_current_high;
6128 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_bias_current_low;
6129 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_output_power_high;
6130 tmp_stats[i++] = stat_info->xpak_stat.alarm_laser_output_power_low;
6131 tmp_stats[i++] = stat_info->xpak_stat.warn_transceiver_temp_high;
6132 tmp_stats[i++] = stat_info->xpak_stat.warn_transceiver_temp_low;
6133 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_bias_current_high;
6134 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_bias_current_low;
6135 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_output_power_high;
6136 tmp_stats[i++] = stat_info->xpak_stat.warn_laser_output_power_low;
6137 tmp_stats[i++] = stat_info->sw_stat.clubbed_frms_cnt;
6138 tmp_stats[i++] = stat_info->sw_stat.sending_both;
6139 tmp_stats[i++] = stat_info->sw_stat.outof_sequence_pkts;
6140 tmp_stats[i++] = stat_info->sw_stat.flush_max_pkts;
6141 if (stat_info->sw_stat.num_aggregations) {
6142 u64 tmp = stat_info->sw_stat.sum_avg_pkts_aggregated;
6145 * Since 64-bit divide does not work on all platforms,
6146 * do repeated subtraction.
6148 while (tmp >= stat_info->sw_stat.num_aggregations) {
6149 tmp -= stat_info->sw_stat.num_aggregations;
6152 tmp_stats[i++] = count;
6156 tmp_stats[i++] = stat_info->sw_stat.mem_alloc_fail_cnt;
6157 tmp_stats[i++] = stat_info->sw_stat.pci_map_fail_cnt;
6158 tmp_stats[i++] = stat_info->sw_stat.watchdog_timer_cnt;
6159 tmp_stats[i++] = stat_info->sw_stat.mem_allocated;
6160 tmp_stats[i++] = stat_info->sw_stat.mem_freed;
6161 tmp_stats[i++] = stat_info->sw_stat.link_up_cnt;
6162 tmp_stats[i++] = stat_info->sw_stat.link_down_cnt;
6163 tmp_stats[i++] = stat_info->sw_stat.link_up_time;
6164 tmp_stats[i++] = stat_info->sw_stat.link_down_time;
6166 tmp_stats[i++] = stat_info->sw_stat.tx_buf_abort_cnt;
6167 tmp_stats[i++] = stat_info->sw_stat.tx_desc_abort_cnt;
6168 tmp_stats[i++] = stat_info->sw_stat.tx_parity_err_cnt;
6169 tmp_stats[i++] = stat_info->sw_stat.tx_link_loss_cnt;
6170 tmp_stats[i++] = stat_info->sw_stat.tx_list_proc_err_cnt;
6172 tmp_stats[i++] = stat_info->sw_stat.rx_parity_err_cnt;
6173 tmp_stats[i++] = stat_info->sw_stat.rx_abort_cnt;
6174 tmp_stats[i++] = stat_info->sw_stat.rx_parity_abort_cnt;
6175 tmp_stats[i++] = stat_info->sw_stat.rx_rda_fail_cnt;
6176 tmp_stats[i++] = stat_info->sw_stat.rx_unkn_prot_cnt;
6177 tmp_stats[i++] = stat_info->sw_stat.rx_fcs_err_cnt;
6178 tmp_stats[i++] = stat_info->sw_stat.rx_buf_size_err_cnt;
6179 tmp_stats[i++] = stat_info->sw_stat.rx_rxd_corrupt_cnt;
6180 tmp_stats[i++] = stat_info->sw_stat.rx_unkn_err_cnt;
6181 tmp_stats[i++] = stat_info->sw_stat.tda_err_cnt;
6182 tmp_stats[i++] = stat_info->sw_stat.pfc_err_cnt;
6183 tmp_stats[i++] = stat_info->sw_stat.pcc_err_cnt;
6184 tmp_stats[i++] = stat_info->sw_stat.tti_err_cnt;
6185 tmp_stats[i++] = stat_info->sw_stat.tpa_err_cnt;
6186 tmp_stats[i++] = stat_info->sw_stat.sm_err_cnt;
6187 tmp_stats[i++] = stat_info->sw_stat.lso_err_cnt;
6188 tmp_stats[i++] = stat_info->sw_stat.mac_tmac_err_cnt;
6189 tmp_stats[i++] = stat_info->sw_stat.mac_rmac_err_cnt;
6190 tmp_stats[i++] = stat_info->sw_stat.xgxs_txgxs_err_cnt;
6191 tmp_stats[i++] = stat_info->sw_stat.xgxs_rxgxs_err_cnt;
6192 tmp_stats[i++] = stat_info->sw_stat.rc_err_cnt;
6193 tmp_stats[i++] = stat_info->sw_stat.prc_pcix_err_cnt;
6194 tmp_stats[i++] = stat_info->sw_stat.rpa_err_cnt;
6195 tmp_stats[i++] = stat_info->sw_stat.rda_err_cnt;
6196 tmp_stats[i++] = stat_info->sw_stat.rti_err_cnt;
6197 tmp_stats[i++] = stat_info->sw_stat.mc_err_cnt;
6200 static int s2io_ethtool_get_regs_len(struct net_device *dev)
6202 return (XENA_REG_SPACE);
6206 static u32 s2io_ethtool_get_rx_csum(struct net_device * dev)
6208 struct s2io_nic *sp = dev->priv;
6210 return (sp->rx_csum);
6213 static int s2io_ethtool_set_rx_csum(struct net_device *dev, u32 data)
6215 struct s2io_nic *sp = dev->priv;
6225 static int s2io_get_eeprom_len(struct net_device *dev)
6227 return (XENA_EEPROM_SPACE);
6230 static int s2io_get_sset_count(struct net_device *dev, int sset)
6232 struct s2io_nic *sp = dev->priv;
6236 return S2IO_TEST_LEN;
6238 switch(sp->device_type) {
6239 case XFRAME_I_DEVICE:
6240 return XFRAME_I_STAT_LEN;
6241 case XFRAME_II_DEVICE:
6242 return XFRAME_II_STAT_LEN;
6251 static void s2io_ethtool_get_strings(struct net_device *dev,
6252 u32 stringset, u8 * data)
6255 struct s2io_nic *sp = dev->priv;
6257 switch (stringset) {
6259 memcpy(data, s2io_gstrings, S2IO_STRINGS_LEN);
6262 stat_size = sizeof(ethtool_xena_stats_keys);
6263 memcpy(data, ðtool_xena_stats_keys,stat_size);
6264 if(sp->device_type == XFRAME_II_DEVICE) {
6265 memcpy(data + stat_size,
6266 ðtool_enhanced_stats_keys,
6267 sizeof(ethtool_enhanced_stats_keys));
6268 stat_size += sizeof(ethtool_enhanced_stats_keys);
6271 memcpy(data + stat_size, ðtool_driver_stats_keys,
6272 sizeof(ethtool_driver_stats_keys));
6276 static int s2io_ethtool_op_set_tx_csum(struct net_device *dev, u32 data)
6279 dev->features |= NETIF_F_IP_CSUM;
6281 dev->features &= ~NETIF_F_IP_CSUM;
6286 static u32 s2io_ethtool_op_get_tso(struct net_device *dev)
6288 return (dev->features & NETIF_F_TSO) != 0;
6290 static int s2io_ethtool_op_set_tso(struct net_device *dev, u32 data)
6293 dev->features |= (NETIF_F_TSO | NETIF_F_TSO6);
6295 dev->features &= ~(NETIF_F_TSO | NETIF_F_TSO6);
6300 static const struct ethtool_ops netdev_ethtool_ops = {
6301 .get_settings = s2io_ethtool_gset,
6302 .set_settings = s2io_ethtool_sset,
6303 .get_drvinfo = s2io_ethtool_gdrvinfo,
6304 .get_regs_len = s2io_ethtool_get_regs_len,
6305 .get_regs = s2io_ethtool_gregs,
6306 .get_link = ethtool_op_get_link,
6307 .get_eeprom_len = s2io_get_eeprom_len,
6308 .get_eeprom = s2io_ethtool_geeprom,
6309 .set_eeprom = s2io_ethtool_seeprom,
6310 .get_ringparam = s2io_ethtool_gringparam,
6311 .get_pauseparam = s2io_ethtool_getpause_data,
6312 .set_pauseparam = s2io_ethtool_setpause_data,
6313 .get_rx_csum = s2io_ethtool_get_rx_csum,
6314 .set_rx_csum = s2io_ethtool_set_rx_csum,
6315 .set_tx_csum = s2io_ethtool_op_set_tx_csum,
6316 .set_sg = ethtool_op_set_sg,
6317 .get_tso = s2io_ethtool_op_get_tso,
6318 .set_tso = s2io_ethtool_op_set_tso,
6319 .set_ufo = ethtool_op_set_ufo,
6320 .self_test = s2io_ethtool_test,
6321 .get_strings = s2io_ethtool_get_strings,
6322 .phys_id = s2io_ethtool_idnic,
6323 .get_ethtool_stats = s2io_get_ethtool_stats,
6324 .get_sset_count = s2io_get_sset_count,
6328 * s2io_ioctl - Entry point for the Ioctl
6329 * @dev : Device pointer.
6330 * @ifr : An IOCTL specefic structure, that can contain a pointer to
6331 * a proprietary structure used to pass information to the driver.
6332 * @cmd : This is used to distinguish between the different commands that
6333 * can be passed to the IOCTL functions.
6335 * Currently there are no special functionality supported in IOCTL, hence
6336 * function always return EOPNOTSUPPORTED
6339 static int s2io_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
6345 * s2io_change_mtu - entry point to change MTU size for the device.
6346 * @dev : device pointer.
6347 * @new_mtu : the new MTU size for the device.
6348 * Description: A driver entry point to change MTU size for the device.
6349 * Before changing the MTU the device must be stopped.
6351 * 0 on success and an appropriate (-)ve integer as defined in errno.h
6355 static int s2io_change_mtu(struct net_device *dev, int new_mtu)
6357 struct s2io_nic *sp = dev->priv;
6359 if ((new_mtu < MIN_MTU) || (new_mtu > S2IO_JUMBO_SIZE)) {
6360 DBG_PRINT(ERR_DBG, "%s: MTU size is invalid.\n",
6366 if (netif_running(dev)) {
6368 netif_stop_queue(dev);
6369 if (s2io_card_up(sp)) {
6370 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
6373 if (netif_queue_stopped(dev))
6374 netif_wake_queue(dev);
6375 } else { /* Device is down */
6376 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6377 u64 val64 = new_mtu;
6379 writeq(vBIT(val64, 2, 14), &bar0->rmac_max_pyld_len);
6386 * s2io_tasklet - Bottom half of the ISR.
6387 * @dev_adr : address of the device structure in dma_addr_t format.
6389 * This is the tasklet or the bottom half of the ISR. This is
6390 * an extension of the ISR which is scheduled by the scheduler to be run
6391 * when the load on the CPU is low. All low priority tasks of the ISR can
6392 * be pushed into the tasklet. For now the tasklet is used only to
6393 * replenish the Rx buffers in the Rx buffer descriptors.
6398 static void s2io_tasklet(unsigned long dev_addr)
6400 struct net_device *dev = (struct net_device *) dev_addr;
6401 struct s2io_nic *sp = dev->priv;
6403 struct mac_info *mac_control;
6404 struct config_param *config;
6406 mac_control = &sp->mac_control;
6407 config = &sp->config;
6409 if (!TASKLET_IN_USE) {
6410 for (i = 0; i < config->rx_ring_num; i++) {
6411 ret = fill_rx_buffers(sp, i);
6412 if (ret == -ENOMEM) {
6413 DBG_PRINT(INFO_DBG, "%s: Out of ",
6415 DBG_PRINT(INFO_DBG, "memory in tasklet\n");
6417 } else if (ret == -EFILL) {
6419 "%s: Rx Ring %d is full\n",
6424 clear_bit(0, (&sp->tasklet_status));
6429 * s2io_set_link - Set the LInk status
6430 * @data: long pointer to device private structue
6431 * Description: Sets the link status for the adapter
6434 static void s2io_set_link(struct work_struct *work)
6436 struct s2io_nic *nic = container_of(work, struct s2io_nic, set_link_task);
6437 struct net_device *dev = nic->dev;
6438 struct XENA_dev_config __iomem *bar0 = nic->bar0;
6444 if (!netif_running(dev))
6447 if (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(nic->state))) {
6448 /* The card is being reset, no point doing anything */
6452 subid = nic->pdev->subsystem_device;
6453 if (s2io_link_fault_indication(nic) == MAC_RMAC_ERR_TIMER) {
6455 * Allow a small delay for the NICs self initiated
6456 * cleanup to complete.
6461 val64 = readq(&bar0->adapter_status);
6462 if (LINK_IS_UP(val64)) {
6463 if (!(readq(&bar0->adapter_control) & ADAPTER_CNTL_EN)) {
6464 if (verify_xena_quiescence(nic)) {
6465 val64 = readq(&bar0->adapter_control);
6466 val64 |= ADAPTER_CNTL_EN;
6467 writeq(val64, &bar0->adapter_control);
6468 if (CARDS_WITH_FAULTY_LINK_INDICATORS(
6469 nic->device_type, subid)) {
6470 val64 = readq(&bar0->gpio_control);
6471 val64 |= GPIO_CTRL_GPIO_0;
6472 writeq(val64, &bar0->gpio_control);
6473 val64 = readq(&bar0->gpio_control);
6475 val64 |= ADAPTER_LED_ON;
6476 writeq(val64, &bar0->adapter_control);
6478 nic->device_enabled_once = TRUE;
6480 DBG_PRINT(ERR_DBG, "%s: Error: ", dev->name);
6481 DBG_PRINT(ERR_DBG, "device is not Quiescent\n");
6482 netif_stop_queue(dev);
6485 val64 = readq(&bar0->adapter_control);
6486 val64 |= ADAPTER_LED_ON;
6487 writeq(val64, &bar0->adapter_control);
6488 s2io_link(nic, LINK_UP);
6490 if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
6492 val64 = readq(&bar0->gpio_control);
6493 val64 &= ~GPIO_CTRL_GPIO_0;
6494 writeq(val64, &bar0->gpio_control);
6495 val64 = readq(&bar0->gpio_control);
6498 val64 = readq(&bar0->adapter_control);
6499 val64 = val64 &(~ADAPTER_LED_ON);
6500 writeq(val64, &bar0->adapter_control);
6501 s2io_link(nic, LINK_DOWN);
6503 clear_bit(__S2IO_STATE_LINK_TASK, &(nic->state));
6509 static int set_rxd_buffer_pointer(struct s2io_nic *sp, struct RxD_t *rxdp,
6511 struct sk_buff **skb, u64 *temp0, u64 *temp1,
6512 u64 *temp2, int size)
6514 struct net_device *dev = sp->dev;
6515 struct swStat *stats = &sp->mac_control.stats_info->sw_stat;
6517 if ((sp->rxd_mode == RXD_MODE_1) && (rxdp->Host_Control == 0)) {
6518 struct RxD1 *rxdp1 = (struct RxD1 *)rxdp;
6521 DBG_PRINT(INFO_DBG, "SKB is not NULL\n");
6523 * As Rx frame are not going to be processed,
6524 * using same mapped address for the Rxd
6527 rxdp1->Buffer0_ptr = *temp0;
6529 *skb = dev_alloc_skb(size);
6531 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
6532 DBG_PRINT(INFO_DBG, "memory to allocate ");
6533 DBG_PRINT(INFO_DBG, "1 buf mode SKBs\n");
6534 sp->mac_control.stats_info->sw_stat. \
6535 mem_alloc_fail_cnt++;
6538 sp->mac_control.stats_info->sw_stat.mem_allocated
6539 += (*skb)->truesize;
6540 /* storing the mapped addr in a temp variable
6541 * such it will be used for next rxd whose
6542 * Host Control is NULL
6544 rxdp1->Buffer0_ptr = *temp0 =
6545 pci_map_single( sp->pdev, (*skb)->data,
6546 size - NET_IP_ALIGN,
6547 PCI_DMA_FROMDEVICE);
6548 if( (rxdp1->Buffer0_ptr == 0) ||
6549 (rxdp1->Buffer0_ptr == DMA_ERROR_CODE)) {
6550 goto memalloc_failed;
6552 rxdp->Host_Control = (unsigned long) (*skb);
6554 } else if ((sp->rxd_mode == RXD_MODE_3B) && (rxdp->Host_Control == 0)) {
6555 struct RxD3 *rxdp3 = (struct RxD3 *)rxdp;
6556 /* Two buffer Mode */
6558 rxdp3->Buffer2_ptr = *temp2;
6559 rxdp3->Buffer0_ptr = *temp0;
6560 rxdp3->Buffer1_ptr = *temp1;
6562 *skb = dev_alloc_skb(size);
6564 DBG_PRINT(INFO_DBG, "%s: Out of ", dev->name);
6565 DBG_PRINT(INFO_DBG, "memory to allocate ");
6566 DBG_PRINT(INFO_DBG, "2 buf mode SKBs\n");
6567 sp->mac_control.stats_info->sw_stat. \
6568 mem_alloc_fail_cnt++;
6571 sp->mac_control.stats_info->sw_stat.mem_allocated
6572 += (*skb)->truesize;
6573 rxdp3->Buffer2_ptr = *temp2 =
6574 pci_map_single(sp->pdev, (*skb)->data,
6576 PCI_DMA_FROMDEVICE);
6577 if( (rxdp3->Buffer2_ptr == 0) ||
6578 (rxdp3->Buffer2_ptr == DMA_ERROR_CODE)) {
6579 goto memalloc_failed;
6581 rxdp3->Buffer0_ptr = *temp0 =
6582 pci_map_single( sp->pdev, ba->ba_0, BUF0_LEN,
6583 PCI_DMA_FROMDEVICE);
6584 if( (rxdp3->Buffer0_ptr == 0) ||
6585 (rxdp3->Buffer0_ptr == DMA_ERROR_CODE)) {
6586 pci_unmap_single (sp->pdev,
6587 (dma_addr_t)rxdp3->Buffer2_ptr,
6588 dev->mtu + 4, PCI_DMA_FROMDEVICE);
6589 goto memalloc_failed;
6591 rxdp->Host_Control = (unsigned long) (*skb);
6593 /* Buffer-1 will be dummy buffer not used */
6594 rxdp3->Buffer1_ptr = *temp1 =
6595 pci_map_single(sp->pdev, ba->ba_1, BUF1_LEN,
6596 PCI_DMA_FROMDEVICE);
6597 if( (rxdp3->Buffer1_ptr == 0) ||
6598 (rxdp3->Buffer1_ptr == DMA_ERROR_CODE)) {
6599 pci_unmap_single (sp->pdev,
6600 (dma_addr_t)rxdp3->Buffer0_ptr,
6601 BUF0_LEN, PCI_DMA_FROMDEVICE);
6602 pci_unmap_single (sp->pdev,
6603 (dma_addr_t)rxdp3->Buffer2_ptr,
6604 dev->mtu + 4, PCI_DMA_FROMDEVICE);
6605 goto memalloc_failed;
6611 stats->pci_map_fail_cnt++;
6612 stats->mem_freed += (*skb)->truesize;
6613 dev_kfree_skb(*skb);
6617 static void set_rxd_buffer_size(struct s2io_nic *sp, struct RxD_t *rxdp,
6620 struct net_device *dev = sp->dev;
6621 if (sp->rxd_mode == RXD_MODE_1) {
6622 rxdp->Control_2 = SET_BUFFER0_SIZE_1( size - NET_IP_ALIGN);
6623 } else if (sp->rxd_mode == RXD_MODE_3B) {
6624 rxdp->Control_2 = SET_BUFFER0_SIZE_3(BUF0_LEN);
6625 rxdp->Control_2 |= SET_BUFFER1_SIZE_3(1);
6626 rxdp->Control_2 |= SET_BUFFER2_SIZE_3( dev->mtu + 4);
6630 static int rxd_owner_bit_reset(struct s2io_nic *sp)
6632 int i, j, k, blk_cnt = 0, size;
6633 struct mac_info * mac_control = &sp->mac_control;
6634 struct config_param *config = &sp->config;
6635 struct net_device *dev = sp->dev;
6636 struct RxD_t *rxdp = NULL;
6637 struct sk_buff *skb = NULL;
6638 struct buffAdd *ba = NULL;
6639 u64 temp0_64 = 0, temp1_64 = 0, temp2_64 = 0;
6641 /* Calculate the size based on ring mode */
6642 size = dev->mtu + HEADER_ETHERNET_II_802_3_SIZE +
6643 HEADER_802_2_SIZE + HEADER_SNAP_SIZE;
6644 if (sp->rxd_mode == RXD_MODE_1)
6645 size += NET_IP_ALIGN;
6646 else if (sp->rxd_mode == RXD_MODE_3B)
6647 size = dev->mtu + ALIGN_SIZE + BUF0_LEN + 4;
6649 for (i = 0; i < config->rx_ring_num; i++) {
6650 blk_cnt = config->rx_cfg[i].num_rxd /
6651 (rxd_count[sp->rxd_mode] +1);
6653 for (j = 0; j < blk_cnt; j++) {
6654 for (k = 0; k < rxd_count[sp->rxd_mode]; k++) {
6655 rxdp = mac_control->rings[i].
6656 rx_blocks[j].rxds[k].virt_addr;
6657 if(sp->rxd_mode == RXD_MODE_3B)
6658 ba = &mac_control->rings[i].ba[j][k];
6659 if (set_rxd_buffer_pointer(sp, rxdp, ba,
6660 &skb,(u64 *)&temp0_64,
6667 set_rxd_buffer_size(sp, rxdp, size);
6669 /* flip the Ownership bit to Hardware */
6670 rxdp->Control_1 |= RXD_OWN_XENA;
6678 static int s2io_add_isr(struct s2io_nic * sp)
6681 struct net_device *dev = sp->dev;
6684 if (sp->config.intr_type == MSI_X)
6685 ret = s2io_enable_msi_x(sp);
6687 DBG_PRINT(ERR_DBG, "%s: Defaulting to INTA\n", dev->name);
6688 sp->config.intr_type = INTA;
6691 /* Store the values of the MSIX table in the struct s2io_nic structure */
6692 store_xmsi_data(sp);
6694 /* After proper initialization of H/W, register ISR */
6695 if (sp->config.intr_type == MSI_X) {
6696 int i, msix_tx_cnt=0,msix_rx_cnt=0;
6698 for (i=1; (sp->s2io_entries[i].in_use == MSIX_FLG); i++) {
6699 if (sp->s2io_entries[i].type == MSIX_FIFO_TYPE) {
6700 sprintf(sp->desc[i], "%s:MSI-X-%d-TX",
6702 err = request_irq(sp->entries[i].vector,
6703 s2io_msix_fifo_handle, 0, sp->desc[i],
6704 sp->s2io_entries[i].arg);
6705 /* If either data or addr is zero print it */
6706 if(!(sp->msix_info[i].addr &&
6707 sp->msix_info[i].data)) {
6708 DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx"
6709 "Data:0x%lx\n",sp->desc[i],
6710 (unsigned long long)
6711 sp->msix_info[i].addr,
6713 ntohl(sp->msix_info[i].data));
6718 sprintf(sp->desc[i], "%s:MSI-X-%d-RX",
6720 err = request_irq(sp->entries[i].vector,
6721 s2io_msix_ring_handle, 0, sp->desc[i],
6722 sp->s2io_entries[i].arg);
6723 /* If either data or addr is zero print it */
6724 if(!(sp->msix_info[i].addr &&
6725 sp->msix_info[i].data)) {
6726 DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx"
6727 "Data:0x%lx\n",sp->desc[i],
6728 (unsigned long long)
6729 sp->msix_info[i].addr,
6731 ntohl(sp->msix_info[i].data));
6737 remove_msix_isr(sp);
6738 DBG_PRINT(ERR_DBG,"%s:MSI-X-%d registration "
6739 "failed\n", dev->name, i);
6740 DBG_PRINT(ERR_DBG, "%s: defaulting to INTA\n",
6742 sp->config.intr_type = INTA;
6745 sp->s2io_entries[i].in_use = MSIX_REGISTERED_SUCCESS;
6748 printk(KERN_INFO "MSI-X-TX %d entries enabled\n",
6750 printk(KERN_INFO "MSI-X-RX %d entries enabled\n",
6754 if (sp->config.intr_type == INTA) {
6755 err = request_irq((int) sp->pdev->irq, s2io_isr, IRQF_SHARED,
6758 DBG_PRINT(ERR_DBG, "%s: ISR registration failed\n",
6765 static void s2io_rem_isr(struct s2io_nic * sp)
6767 if (sp->config.intr_type == MSI_X)
6768 remove_msix_isr(sp);
6770 remove_inta_isr(sp);
6773 static void do_s2io_card_down(struct s2io_nic * sp, int do_io)
6776 struct XENA_dev_config __iomem *bar0 = sp->bar0;
6777 unsigned long flags;
6778 register u64 val64 = 0;
6780 del_timer_sync(&sp->alarm_timer);
6781 /* If s2io_set_link task is executing, wait till it completes. */
6782 while (test_and_set_bit(__S2IO_STATE_LINK_TASK, &(sp->state))) {
6785 clear_bit(__S2IO_STATE_CARD_UP, &sp->state);
6787 /* disable Tx and Rx traffic on the NIC */
6794 tasklet_kill(&sp->task);
6796 /* Check if the device is Quiescent and then Reset the NIC */
6798 /* As per the HW requirement we need to replenish the
6799 * receive buffer to avoid the ring bump. Since there is
6800 * no intention of processing the Rx frame at this pointwe are
6801 * just settting the ownership bit of rxd in Each Rx
6802 * ring to HW and set the appropriate buffer size
6803 * based on the ring mode
6805 rxd_owner_bit_reset(sp);
6807 val64 = readq(&bar0->adapter_status);
6808 if (verify_xena_quiescence(sp)) {
6809 if(verify_pcc_quiescent(sp, sp->device_enabled_once))
6817 "s2io_close:Device not Quiescent ");
6818 DBG_PRINT(ERR_DBG, "adaper status reads 0x%llx\n",
6819 (unsigned long long) val64);
6826 spin_lock_irqsave(&sp->tx_lock, flags);
6827 /* Free all Tx buffers */
6828 free_tx_buffers(sp);
6829 spin_unlock_irqrestore(&sp->tx_lock, flags);
6831 /* Free all Rx buffers */
6832 spin_lock_irqsave(&sp->rx_lock, flags);
6833 free_rx_buffers(sp);
6834 spin_unlock_irqrestore(&sp->rx_lock, flags);
6836 clear_bit(__S2IO_STATE_LINK_TASK, &(sp->state));
6839 static void s2io_card_down(struct s2io_nic * sp)
6841 do_s2io_card_down(sp, 1);
6844 static int s2io_card_up(struct s2io_nic * sp)
6847 struct mac_info *mac_control;
6848 struct config_param *config;
6849 struct net_device *dev = (struct net_device *) sp->dev;
6852 /* Initialize the H/W I/O registers */
6853 if (init_nic(sp) != 0) {
6854 DBG_PRINT(ERR_DBG, "%s: H/W initialization failed\n",
6861 * Initializing the Rx buffers. For now we are considering only 1
6862 * Rx ring and initializing buffers into 30 Rx blocks
6864 mac_control = &sp->mac_control;
6865 config = &sp->config;
6867 for (i = 0; i < config->rx_ring_num; i++) {
6868 if ((ret = fill_rx_buffers(sp, i))) {
6869 DBG_PRINT(ERR_DBG, "%s: Out of memory in Open\n",
6872 free_rx_buffers(sp);
6875 DBG_PRINT(INFO_DBG, "Buf in ring:%d is %d:\n", i,
6876 atomic_read(&sp->rx_bufs_left[i]));
6878 /* Maintain the state prior to the open */
6879 if (sp->promisc_flg)
6880 sp->promisc_flg = 0;
6881 if (sp->m_cast_flg) {
6883 sp->all_multi_pos= 0;
6886 /* Setting its receive mode */
6887 s2io_set_multicast(dev);
6890 /* Initialize max aggregatable pkts per session based on MTU */
6891 sp->lro_max_aggr_per_sess = ((1<<16) - 1) / dev->mtu;
6892 /* Check if we can use(if specified) user provided value */
6893 if (lro_max_pkts < sp->lro_max_aggr_per_sess)
6894 sp->lro_max_aggr_per_sess = lro_max_pkts;
6897 /* Enable Rx Traffic and interrupts on the NIC */
6898 if (start_nic(sp)) {
6899 DBG_PRINT(ERR_DBG, "%s: Starting NIC failed\n", dev->name);
6901 free_rx_buffers(sp);
6905 /* Add interrupt service routine */
6906 if (s2io_add_isr(sp) != 0) {
6907 if (sp->config.intr_type == MSI_X)
6910 free_rx_buffers(sp);
6914 S2IO_TIMER_CONF(sp->alarm_timer, s2io_alarm_handle, sp, (HZ/2));
6916 /* Enable tasklet for the device */
6917 tasklet_init(&sp->task, s2io_tasklet, (unsigned long) dev);
6919 /* Enable select interrupts */
6920 en_dis_err_alarms(sp, ENA_ALL_INTRS, ENABLE_INTRS);
6921 if (sp->config.intr_type != INTA)
6922 en_dis_able_nic_intrs(sp, ENA_ALL_INTRS, DISABLE_INTRS);
6924 interruptible = TX_TRAFFIC_INTR | RX_TRAFFIC_INTR;
6925 interruptible |= TX_PIC_INTR;
6926 en_dis_able_nic_intrs(sp, interruptible, ENABLE_INTRS);
6929 set_bit(__S2IO_STATE_CARD_UP, &sp->state);
6934 * s2io_restart_nic - Resets the NIC.
6935 * @data : long pointer to the device private structure
6937 * This function is scheduled to be run by the s2io_tx_watchdog
6938 * function after 0.5 secs to reset the NIC. The idea is to reduce
6939 * the run time of the watch dog routine which is run holding a
6943 static void s2io_restart_nic(struct work_struct *work)
6945 struct s2io_nic *sp = container_of(work, struct s2io_nic, rst_timer_task);
6946 struct net_device *dev = sp->dev;
6950 if (!netif_running(dev))
6954 if (s2io_card_up(sp)) {
6955 DBG_PRINT(ERR_DBG, "%s: Device bring up failed\n",
6958 netif_wake_queue(dev);
6959 DBG_PRINT(ERR_DBG, "%s: was reset by Tx watchdog timer\n",
6966 * s2io_tx_watchdog - Watchdog for transmit side.
6967 * @dev : Pointer to net device structure
6969 * This function is triggered if the Tx Queue is stopped
6970 * for a pre-defined amount of time when the Interface is still up.
6971 * If the Interface is jammed in such a situation, the hardware is
6972 * reset (by s2io_close) and restarted again (by s2io_open) to
6973 * overcome any problem that might have been caused in the hardware.
6978 static void s2io_tx_watchdog(struct net_device *dev)
6980 struct s2io_nic *sp = dev->priv;
6982 if (netif_carrier_ok(dev)) {
6983 sp->mac_control.stats_info->sw_stat.watchdog_timer_cnt++;
6984 schedule_work(&sp->rst_timer_task);
6985 sp->mac_control.stats_info->sw_stat.soft_reset_cnt++;
6990 * rx_osm_handler - To perform some OS related operations on SKB.
6991 * @sp: private member of the device structure,pointer to s2io_nic structure.
6992 * @skb : the socket buffer pointer.
6993 * @len : length of the packet
6994 * @cksum : FCS checksum of the frame.
6995 * @ring_no : the ring from which this RxD was extracted.
6997 * This function is called by the Rx interrupt serivce routine to perform
6998 * some OS related operations on the SKB before passing it to the upper
6999 * layers. It mainly checks if the checksum is OK, if so adds it to the
7000 * SKBs cksum variable, increments the Rx packet count and passes the SKB
7001 * to the upper layer. If the checksum is wrong, it increments the Rx
7002 * packet error count, frees the SKB and returns error.
7004 * SUCCESS on success and -1 on failure.
7006 static int rx_osm_handler(struct ring_info *ring_data, struct RxD_t * rxdp)
7008 struct s2io_nic *sp = ring_data->nic;
7009 struct net_device *dev = (struct net_device *) sp->dev;
7010 struct sk_buff *skb = (struct sk_buff *)
7011 ((unsigned long) rxdp->Host_Control);
7012 int ring_no = ring_data->ring_no;
7013 u16 l3_csum, l4_csum;
7014 unsigned long long err = rxdp->Control_1 & RXD_T_CODE;
7021 /* Check for parity error */
7023 sp->mac_control.stats_info->sw_stat.parity_err_cnt++;
7025 err_mask = err >> 48;
7028 sp->mac_control.stats_info->sw_stat.
7029 rx_parity_err_cnt++;
7033 sp->mac_control.stats_info->sw_stat.
7038 sp->mac_control.stats_info->sw_stat.
7039 rx_parity_abort_cnt++;
7043 sp->mac_control.stats_info->sw_stat.
7048 sp->mac_control.stats_info->sw_stat.
7053 sp->mac_control.stats_info->sw_stat.
7058 sp->mac_control.stats_info->sw_stat.
7059 rx_buf_size_err_cnt++;
7063 sp->mac_control.stats_info->sw_stat.
7064 rx_rxd_corrupt_cnt++;
7068 sp->mac_control.stats_info->sw_stat.
7073 * Drop the packet if bad transfer code. Exception being
7074 * 0x5, which could be due to unsupported IPv6 extension header.
7075 * In this case, we let stack handle the packet.
7076 * Note that in this case, since checksum will be incorrect,
7077 * stack will validate the same.
7079 if (err_mask != 0x5) {
7080 DBG_PRINT(ERR_DBG, "%s: Rx error Value: 0x%x\n",
7081 dev->name, err_mask);
7082 sp->stats.rx_crc_errors++;
7083 sp->mac_control.stats_info->sw_stat.mem_freed
7086 atomic_dec(&sp->rx_bufs_left[ring_no]);
7087 rxdp->Host_Control = 0;
7092 /* Updating statistics */
7093 sp->stats.rx_packets++;
7094 rxdp->Host_Control = 0;
7095 if (sp->rxd_mode == RXD_MODE_1) {
7096 int len = RXD_GET_BUFFER0_SIZE_1(rxdp->Control_2);
7098 sp->stats.rx_bytes += len;
7101 } else if (sp->rxd_mode == RXD_MODE_3B) {
7102 int get_block = ring_data->rx_curr_get_info.block_index;
7103 int get_off = ring_data->rx_curr_get_info.offset;
7104 int buf0_len = RXD_GET_BUFFER0_SIZE_3(rxdp->Control_2);
7105 int buf2_len = RXD_GET_BUFFER2_SIZE_3(rxdp->Control_2);
7106 unsigned char *buff = skb_push(skb, buf0_len);
7108 struct buffAdd *ba = &ring_data->ba[get_block][get_off];
7109 sp->stats.rx_bytes += buf0_len + buf2_len;
7110 memcpy(buff, ba->ba_0, buf0_len);
7111 skb_put(skb, buf2_len);
7114 if ((rxdp->Control_1 & TCP_OR_UDP_FRAME) && ((!sp->lro) ||
7115 (sp->lro && (!(rxdp->Control_1 & RXD_FRAME_IP_FRAG)))) &&
7117 l3_csum = RXD_GET_L3_CKSUM(rxdp->Control_1);
7118 l4_csum = RXD_GET_L4_CKSUM(rxdp->Control_1);
7119 if ((l3_csum == L3_CKSUM_OK) && (l4_csum == L4_CKSUM_OK)) {
7121 * NIC verifies if the Checksum of the received
7122 * frame is Ok or not and accordingly returns
7123 * a flag in the RxD.
7125 skb->ip_summed = CHECKSUM_UNNECESSARY;
7131 ret = s2io_club_tcp_session(skb->data, &tcp,
7135 case 3: /* Begin anew */
7138 case 1: /* Aggregate */
7140 lro_append_pkt(sp, lro,
7144 case 4: /* Flush session */
7146 lro_append_pkt(sp, lro,
7148 queue_rx_frame(lro->parent);
7149 clear_lro_session(lro);
7150 sp->mac_control.stats_info->
7151 sw_stat.flush_max_pkts++;
7154 case 2: /* Flush both */
7155 lro->parent->data_len =
7157 sp->mac_control.stats_info->
7158 sw_stat.sending_both++;
7159 queue_rx_frame(lro->parent);
7160 clear_lro_session(lro);
7162 case 0: /* sessions exceeded */
7163 case -1: /* non-TCP or not
7167 * First pkt in session not
7168 * L3/L4 aggregatable
7173 "%s: Samadhana!!\n",
7180 * Packet with erroneous checksum, let the
7181 * upper layers deal with it.
7183 skb->ip_summed = CHECKSUM_NONE;
7186 skb->ip_summed = CHECKSUM_NONE;
7188 sp->mac_control.stats_info->sw_stat.mem_freed += skb->truesize;
7190 skb->protocol = eth_type_trans(skb, dev);
7191 if ((sp->vlgrp && RXD_GET_VLAN_TAG(rxdp->Control_2) &&
7193 /* Queueing the vlan frame to the upper layer */
7195 vlan_hwaccel_receive_skb(skb, sp->vlgrp,
7196 RXD_GET_VLAN_TAG(rxdp->Control_2));
7198 vlan_hwaccel_rx(skb, sp->vlgrp,
7199 RXD_GET_VLAN_TAG(rxdp->Control_2));
7202 netif_receive_skb(skb);
7208 queue_rx_frame(skb);
7210 dev->last_rx = jiffies;
7212 atomic_dec(&sp->rx_bufs_left[ring_no]);
7217 * s2io_link - stops/starts the Tx queue.
7218 * @sp : private member of the device structure, which is a pointer to the
7219 * s2io_nic structure.
7220 * @link : inidicates whether link is UP/DOWN.
7222 * This function stops/starts the Tx queue depending on whether the link
7223 * status of the NIC is is down or up. This is called by the Alarm
7224 * interrupt handler whenever a link change interrupt comes up.
7229 static void s2io_link(struct s2io_nic * sp, int link)
7231 struct net_device *dev = (struct net_device *) sp->dev;
7233 if (link != sp->last_link_state) {
7234 if (link == LINK_DOWN) {
7235 DBG_PRINT(ERR_DBG, "%s: Link down\n", dev->name);
7236 netif_carrier_off(dev);
7237 if(sp->mac_control.stats_info->sw_stat.link_up_cnt)
7238 sp->mac_control.stats_info->sw_stat.link_up_time =
7239 jiffies - sp->start_time;
7240 sp->mac_control.stats_info->sw_stat.link_down_cnt++;
7242 DBG_PRINT(ERR_DBG, "%s: Link Up\n", dev->name);
7243 if (sp->mac_control.stats_info->sw_stat.link_down_cnt)
7244 sp->mac_control.stats_info->sw_stat.link_down_time =
7245 jiffies - sp->start_time;
7246 sp->mac_control.stats_info->sw_stat.link_up_cnt++;
7247 netif_carrier_on(dev);
7250 sp->last_link_state = link;
7251 sp->start_time = jiffies;
7255 * s2io_init_pci -Initialization of PCI and PCI-X configuration registers .
7256 * @sp : private member of the device structure, which is a pointer to the
7257 * s2io_nic structure.
7259 * This function initializes a few of the PCI and PCI-X configuration registers
7260 * with recommended values.
7265 static void s2io_init_pci(struct s2io_nic * sp)
7267 u16 pci_cmd = 0, pcix_cmd = 0;
7269 /* Enable Data Parity Error Recovery in PCI-X command register. */
7270 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7272 pci_write_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7274 pci_read_config_word(sp->pdev, PCIX_COMMAND_REGISTER,
7277 /* Set the PErr Response bit in PCI command register. */
7278 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7279 pci_write_config_word(sp->pdev, PCI_COMMAND,
7280 (pci_cmd | PCI_COMMAND_PARITY));
7281 pci_read_config_word(sp->pdev, PCI_COMMAND, &pci_cmd);
7284 static int s2io_verify_parm(struct pci_dev *pdev, u8 *dev_intr_type)
7286 if ( tx_fifo_num > 8) {
7287 DBG_PRINT(ERR_DBG, "s2io: Requested number of Tx fifos not "
7289 DBG_PRINT(ERR_DBG, "s2io: Default to 8 Tx fifos\n");
7292 if ( rx_ring_num > 8) {
7293 DBG_PRINT(ERR_DBG, "s2io: Requested number of Rx rings not "
7295 DBG_PRINT(ERR_DBG, "s2io: Default to 8 Rx rings\n");
7298 if (*dev_intr_type != INTA)
7301 if ((*dev_intr_type != INTA) && (*dev_intr_type != MSI_X)) {
7302 DBG_PRINT(ERR_DBG, "s2io: Wrong intr_type requested. "
7303 "Defaulting to INTA\n");
7304 *dev_intr_type = INTA;
7307 if ((*dev_intr_type == MSI_X) &&
7308 ((pdev->device != PCI_DEVICE_ID_HERC_WIN) &&
7309 (pdev->device != PCI_DEVICE_ID_HERC_UNI))) {
7310 DBG_PRINT(ERR_DBG, "s2io: Xframe I does not support MSI_X. "
7311 "Defaulting to INTA\n");
7312 *dev_intr_type = INTA;
7315 if ((rx_ring_mode != 1) && (rx_ring_mode != 2)) {
7316 DBG_PRINT(ERR_DBG, "s2io: Requested ring mode not supported\n");
7317 DBG_PRINT(ERR_DBG, "s2io: Defaulting to 1-buffer mode\n");
7324 * rts_ds_steer - Receive traffic steering based on IPv4 or IPv6 TOS
7325 * or Traffic class respectively.
7326 * @nic: device peivate variable
7327 * Description: The function configures the receive steering to
7328 * desired receive ring.
7329 * Return Value: SUCCESS on success and
7330 * '-1' on failure (endian settings incorrect).
7332 static int rts_ds_steer(struct s2io_nic *nic, u8 ds_codepoint, u8 ring)
7334 struct XENA_dev_config __iomem *bar0 = nic->bar0;
7335 register u64 val64 = 0;
7337 if (ds_codepoint > 63)
7340 val64 = RTS_DS_MEM_DATA(ring);
7341 writeq(val64, &bar0->rts_ds_mem_data);
7343 val64 = RTS_DS_MEM_CTRL_WE |
7344 RTS_DS_MEM_CTRL_STROBE_NEW_CMD |
7345 RTS_DS_MEM_CTRL_OFFSET(ds_codepoint);
7347 writeq(val64, &bar0->rts_ds_mem_ctrl);
7349 return wait_for_cmd_complete(&bar0->rts_ds_mem_ctrl,
7350 RTS_DS_MEM_CTRL_STROBE_CMD_BEING_EXECUTED,
7355 * s2io_init_nic - Initialization of the adapter .
7356 * @pdev : structure containing the PCI related information of the device.
7357 * @pre: List of PCI devices supported by the driver listed in s2io_tbl.
7359 * The function initializes an adapter identified by the pci_dec structure.
7360 * All OS related initialization including memory and device structure and
7361 * initlaization of the device private variable is done. Also the swapper
7362 * control register is initialized to enable read and write into the I/O
7363 * registers of the device.
7365 * returns 0 on success and negative on failure.
7368 static int __devinit
7369 s2io_init_nic(struct pci_dev *pdev, const struct pci_device_id *pre)
7371 struct s2io_nic *sp;
7372 struct net_device *dev;
7374 int dma_flag = FALSE;
7375 u32 mac_up, mac_down;
7376 u64 val64 = 0, tmp64 = 0;
7377 struct XENA_dev_config __iomem *bar0 = NULL;
7379 struct mac_info *mac_control;
7380 struct config_param *config;
7382 u8 dev_intr_type = intr_type;
7383 DECLARE_MAC_BUF(mac);
7385 if ((ret = s2io_verify_parm(pdev, &dev_intr_type)))
7388 if ((ret = pci_enable_device(pdev))) {
7390 "s2io_init_nic: pci_enable_device failed\n");
7394 if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) {
7395 DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 64bit DMA\n");
7397 if (pci_set_consistent_dma_mask
7398 (pdev, DMA_64BIT_MASK)) {
7400 "Unable to obtain 64bit DMA for \
7401 consistent allocations\n");
7402 pci_disable_device(pdev);
7405 } else if (!pci_set_dma_mask(pdev, DMA_32BIT_MASK)) {
7406 DBG_PRINT(INIT_DBG, "s2io_init_nic: Using 32bit DMA\n");
7408 pci_disable_device(pdev);
7411 if ((ret = pci_request_regions(pdev, s2io_driver_name))) {
7412 DBG_PRINT(ERR_DBG, "%s: Request Regions failed - %x \n", __FUNCTION__, ret);
7413 pci_disable_device(pdev);
7417 dev = alloc_etherdev(sizeof(struct s2io_nic));
7419 DBG_PRINT(ERR_DBG, "Device allocation failed\n");
7420 pci_disable_device(pdev);
7421 pci_release_regions(pdev);
7425 pci_set_master(pdev);
7426 pci_set_drvdata(pdev, dev);
7427 SET_NETDEV_DEV(dev, &pdev->dev);
7429 /* Private member variable initialized to s2io NIC structure */
7431 memset(sp, 0, sizeof(struct s2io_nic));
7434 sp->high_dma_flag = dma_flag;
7435 sp->device_enabled_once = FALSE;
7436 if (rx_ring_mode == 1)
7437 sp->rxd_mode = RXD_MODE_1;
7438 if (rx_ring_mode == 2)
7439 sp->rxd_mode = RXD_MODE_3B;
7441 sp->config.intr_type = dev_intr_type;
7443 if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) ||
7444 (pdev->device == PCI_DEVICE_ID_HERC_UNI))
7445 sp->device_type = XFRAME_II_DEVICE;
7447 sp->device_type = XFRAME_I_DEVICE;
7449 sp->lro = lro_enable;
7451 /* Initialize some PCI/PCI-X fields of the NIC. */
7455 * Setting the device configuration parameters.
7456 * Most of these parameters can be specified by the user during
7457 * module insertion as they are module loadable parameters. If
7458 * these parameters are not not specified during load time, they
7459 * are initialized with default values.
7461 mac_control = &sp->mac_control;
7462 config = &sp->config;
7464 config->napi = napi;
7466 /* Tx side parameters. */
7467 config->tx_fifo_num = tx_fifo_num;
7468 for (i = 0; i < MAX_TX_FIFOS; i++) {
7469 config->tx_cfg[i].fifo_len = tx_fifo_len[i];
7470 config->tx_cfg[i].fifo_priority = i;
7473 /* mapping the QoS priority to the configured fifos */
7474 for (i = 0; i < MAX_TX_FIFOS; i++)
7475 config->fifo_mapping[i] = fifo_map[config->tx_fifo_num][i];
7477 config->tx_intr_type = TXD_INT_TYPE_UTILZ;
7478 for (i = 0; i < config->tx_fifo_num; i++) {
7479 config->tx_cfg[i].f_no_snoop =
7480 (NO_SNOOP_TXD | NO_SNOOP_TXD_BUFFER);
7481 if (config->tx_cfg[i].fifo_len < 65) {
7482 config->tx_intr_type = TXD_INT_TYPE_PER_LIST;
7486 /* + 2 because one Txd for skb->data and one Txd for UFO */
7487 config->max_txds = MAX_SKB_FRAGS + 2;
7489 /* Rx side parameters. */
7490 config->rx_ring_num = rx_ring_num;
7491 for (i = 0; i < MAX_RX_RINGS; i++) {
7492 config->rx_cfg[i].num_rxd = rx_ring_sz[i] *
7493 (rxd_count[sp->rxd_mode] + 1);
7494 config->rx_cfg[i].ring_priority = i;
7497 for (i = 0; i < rx_ring_num; i++) {
7498 config->rx_cfg[i].ring_org = RING_ORG_BUFF1;
7499 config->rx_cfg[i].f_no_snoop =
7500 (NO_SNOOP_RXD | NO_SNOOP_RXD_BUFFER);
7503 /* Setting Mac Control parameters */
7504 mac_control->rmac_pause_time = rmac_pause_time;
7505 mac_control->mc_pause_threshold_q0q3 = mc_pause_threshold_q0q3;
7506 mac_control->mc_pause_threshold_q4q7 = mc_pause_threshold_q4q7;
7509 /* Initialize Ring buffer parameters. */
7510 for (i = 0; i < config->rx_ring_num; i++)
7511 atomic_set(&sp->rx_bufs_left[i], 0);
7513 /* initialize the shared memory used by the NIC and the host */
7514 if (init_shared_mem(sp)) {
7515 DBG_PRINT(ERR_DBG, "%s: Memory allocation failed\n",
7518 goto mem_alloc_failed;
7521 sp->bar0 = ioremap(pci_resource_start(pdev, 0),
7522 pci_resource_len(pdev, 0));
7524 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem1\n",
7527 goto bar0_remap_failed;
7530 sp->bar1 = ioremap(pci_resource_start(pdev, 2),
7531 pci_resource_len(pdev, 2));
7533 DBG_PRINT(ERR_DBG, "%s: Neterion: cannot remap io mem2\n",
7536 goto bar1_remap_failed;
7539 dev->irq = pdev->irq;
7540 dev->base_addr = (unsigned long) sp->bar0;
7542 /* Initializing the BAR1 address as the start of the FIFO pointer. */
7543 for (j = 0; j < MAX_TX_FIFOS; j++) {
7544 mac_control->tx_FIFO_start[j] = (struct TxFIFO_element __iomem *)
7545 (sp->bar1 + (j * 0x00020000));
7548 /* Driver entry points */
7549 dev->open = &s2io_open;
7550 dev->stop = &s2io_close;
7551 dev->hard_start_xmit = &s2io_xmit;
7552 dev->get_stats = &s2io_get_stats;
7553 dev->set_multicast_list = &s2io_set_multicast;
7554 dev->do_ioctl = &s2io_ioctl;
7555 dev->set_mac_address = &s2io_set_mac_addr;
7556 dev->change_mtu = &s2io_change_mtu;
7557 SET_ETHTOOL_OPS(dev, &netdev_ethtool_ops);
7558 dev->features |= NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX;
7559 dev->vlan_rx_register = s2io_vlan_rx_register;
7562 * will use eth_mac_addr() for dev->set_mac_address
7563 * mac address will be set every time dev->open() is called
7565 netif_napi_add(dev, &sp->napi, s2io_poll, 32);
7567 #ifdef CONFIG_NET_POLL_CONTROLLER
7568 dev->poll_controller = s2io_netpoll;
7571 dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
7572 if (sp->high_dma_flag == TRUE)
7573 dev->features |= NETIF_F_HIGHDMA;
7574 dev->features |= NETIF_F_TSO;
7575 dev->features |= NETIF_F_TSO6;
7576 if ((sp->device_type & XFRAME_II_DEVICE) && (ufo)) {
7577 dev->features |= NETIF_F_UFO;
7578 dev->features |= NETIF_F_HW_CSUM;
7581 dev->tx_timeout = &s2io_tx_watchdog;
7582 dev->watchdog_timeo = WATCH_DOG_TIMEOUT;
7583 INIT_WORK(&sp->rst_timer_task, s2io_restart_nic);
7584 INIT_WORK(&sp->set_link_task, s2io_set_link);
7586 pci_save_state(sp->pdev);
7588 /* Setting swapper control on the NIC, for proper reset operation */
7589 if (s2io_set_swapper(sp)) {
7590 DBG_PRINT(ERR_DBG, "%s:swapper settings are wrong\n",
7593 goto set_swap_failed;
7596 /* Verify if the Herc works on the slot its placed into */
7597 if (sp->device_type & XFRAME_II_DEVICE) {
7598 mode = s2io_verify_pci_mode(sp);
7600 DBG_PRINT(ERR_DBG, "%s: ", __FUNCTION__);
7601 DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
7603 goto set_swap_failed;
7607 /* Not needed for Herc */
7608 if (sp->device_type & XFRAME_I_DEVICE) {
7610 * Fix for all "FFs" MAC address problems observed on
7613 fix_mac_address(sp);
7618 * MAC address initialization.
7619 * For now only one mac address will be read and used.
7622 val64 = RMAC_ADDR_CMD_MEM_RD | RMAC_ADDR_CMD_MEM_STROBE_NEW_CMD |
7623 RMAC_ADDR_CMD_MEM_OFFSET(0 + MAC_MAC_ADDR_START_OFFSET);
7624 writeq(val64, &bar0->rmac_addr_cmd_mem);
7625 wait_for_cmd_complete(&bar0->rmac_addr_cmd_mem,
7626 RMAC_ADDR_CMD_MEM_STROBE_CMD_EXECUTING, S2IO_BIT_RESET);
7627 tmp64 = readq(&bar0->rmac_addr_data0_mem);
7628 mac_down = (u32) tmp64;
7629 mac_up = (u32) (tmp64 >> 32);
7631 sp->def_mac_addr[0].mac_addr[3] = (u8) (mac_up);
7632 sp->def_mac_addr[0].mac_addr[2] = (u8) (mac_up >> 8);
7633 sp->def_mac_addr[0].mac_addr[1] = (u8) (mac_up >> 16);
7634 sp->def_mac_addr[0].mac_addr[0] = (u8) (mac_up >> 24);
7635 sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16);
7636 sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24);
7638 /* Set the factory defined MAC address initially */
7639 dev->addr_len = ETH_ALEN;
7640 memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN);
7641 memcpy(dev->perm_addr, dev->dev_addr, ETH_ALEN);
7643 /* Store the values of the MSIX table in the s2io_nic structure */
7644 store_xmsi_data(sp);
7645 /* reset Nic and bring it to known state */
7649 * Initialize the tasklet status and link state flags
7650 * and the card state parameter
7652 sp->tasklet_status = 0;
7655 /* Initialize spinlocks */
7656 spin_lock_init(&sp->tx_lock);
7659 spin_lock_init(&sp->put_lock);
7660 spin_lock_init(&sp->rx_lock);
7663 * SXE-002: Configure link and activity LED to init state
7666 subid = sp->pdev->subsystem_device;
7667 if ((subid & 0xFF) >= 0x07) {
7668 val64 = readq(&bar0->gpio_control);
7669 val64 |= 0x0000800000000000ULL;
7670 writeq(val64, &bar0->gpio_control);
7671 val64 = 0x0411040400000000ULL;
7672 writeq(val64, (void __iomem *) bar0 + 0x2700);
7673 val64 = readq(&bar0->gpio_control);
7676 sp->rx_csum = 1; /* Rx chksum verify enabled by default */
7678 if (register_netdev(dev)) {
7679 DBG_PRINT(ERR_DBG, "Device registration failed\n");
7681 goto register_failed;
7684 DBG_PRINT(ERR_DBG, "Copyright(c) 2002-2007 Neterion Inc.\n");
7685 DBG_PRINT(ERR_DBG, "%s: Neterion %s (rev %d)\n",dev->name,
7686 sp->product_name, pdev->revision);
7687 DBG_PRINT(ERR_DBG, "%s: Driver version %s\n", dev->name,
7688 s2io_driver_version);
7689 DBG_PRINT(ERR_DBG, "%s: MAC ADDR: %s\n",
7690 dev->name, print_mac(mac, dev->dev_addr));
7691 DBG_PRINT(ERR_DBG, "SERIAL NUMBER: %s\n", sp->serial_num);
7692 if (sp->device_type & XFRAME_II_DEVICE) {
7693 mode = s2io_print_pci_mode(sp);
7695 DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
7697 unregister_netdev(dev);
7698 goto set_swap_failed;
7701 switch(sp->rxd_mode) {
7703 DBG_PRINT(ERR_DBG, "%s: 1-Buffer receive mode enabled\n",
7707 DBG_PRINT(ERR_DBG, "%s: 2-Buffer receive mode enabled\n",
7713 DBG_PRINT(ERR_DBG, "%s: NAPI enabled\n", dev->name);
7714 switch(sp->config.intr_type) {
7716 DBG_PRINT(ERR_DBG, "%s: Interrupt type INTA\n", dev->name);
7719 DBG_PRINT(ERR_DBG, "%s: Interrupt type MSI-X\n", dev->name);
7723 DBG_PRINT(ERR_DBG, "%s: Large receive offload enabled\n",
7726 DBG_PRINT(ERR_DBG, "%s: UDP Fragmentation Offload(UFO)"
7727 " enabled\n", dev->name);
7728 /* Initialize device name */
7729 sprintf(sp->name, "%s Neterion %s", dev->name, sp->product_name);
7732 * Make Link state as off at this point, when the Link change
7733 * interrupt comes the state will be automatically changed to
7736 netif_carrier_off(dev);
7747 free_shared_mem(sp);
7748 pci_disable_device(pdev);
7749 pci_release_regions(pdev);
7750 pci_set_drvdata(pdev, NULL);
7757 * s2io_rem_nic - Free the PCI device
7758 * @pdev: structure containing the PCI related information of the device.
7759 * Description: This function is called by the Pci subsystem to release a
7760 * PCI device and free up all resource held up by the device. This could
7761 * be in response to a Hot plug event or when the driver is to be removed
7765 static void __devexit s2io_rem_nic(struct pci_dev *pdev)
7767 struct net_device *dev =
7768 (struct net_device *) pci_get_drvdata(pdev);
7769 struct s2io_nic *sp;
7772 DBG_PRINT(ERR_DBG, "Driver Data is NULL!!\n");
7776 flush_scheduled_work();
7779 unregister_netdev(dev);
7781 free_shared_mem(sp);
7784 pci_release_regions(pdev);
7785 pci_set_drvdata(pdev, NULL);
7787 pci_disable_device(pdev);
7791 * s2io_starter - Entry point for the driver
7792 * Description: This function is the entry point for the driver. It verifies
7793 * the module loadable parameters and initializes PCI configuration space.
7796 static int __init s2io_starter(void)
7798 return pci_register_driver(&s2io_driver);
7802 * s2io_closer - Cleanup routine for the driver
7803 * Description: This function is the cleanup routine for the driver. It unregist * ers the driver.
7806 static __exit void s2io_closer(void)
7808 pci_unregister_driver(&s2io_driver);
7809 DBG_PRINT(INIT_DBG, "cleanup done\n");
7812 module_init(s2io_starter);
7813 module_exit(s2io_closer);
7815 static int check_L2_lro_capable(u8 *buffer, struct iphdr **ip,
7816 struct tcphdr **tcp, struct RxD_t *rxdp)
7819 u8 l2_type = (u8)((rxdp->Control_1 >> 37) & 0x7), ip_len;
7821 if (!(rxdp->Control_1 & RXD_FRAME_PROTO_TCP)) {
7822 DBG_PRINT(INIT_DBG,"%s: Non-TCP frames not supported for LRO\n",
7828 * By default the VLAN field in the MAC is stripped by the card, if this
7829 * feature is turned off in rx_pa_cfg register, then the ip_off field
7830 * has to be shifted by a further 2 bytes
7833 case 0: /* DIX type */
7834 case 4: /* DIX type with VLAN */
7835 ip_off = HEADER_ETHERNET_II_802_3_SIZE;
7837 /* LLC, SNAP etc are considered non-mergeable */
7842 *ip = (struct iphdr *)((u8 *)buffer + ip_off);
7843 ip_len = (u8)((*ip)->ihl);
7845 *tcp = (struct tcphdr *)((unsigned long)*ip + ip_len);
7850 static int check_for_socket_match(struct lro *lro, struct iphdr *ip,
7853 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
7854 if ((lro->iph->saddr != ip->saddr) || (lro->iph->daddr != ip->daddr) ||
7855 (lro->tcph->source != tcp->source) || (lro->tcph->dest != tcp->dest))
7860 static inline int get_l4_pyld_length(struct iphdr *ip, struct tcphdr *tcp)
7862 return(ntohs(ip->tot_len) - (ip->ihl << 2) - (tcp->doff << 2));
7865 static void initiate_new_session(struct lro *lro, u8 *l2h,
7866 struct iphdr *ip, struct tcphdr *tcp, u32 tcp_pyld_len)
7868 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
7872 lro->tcp_next_seq = tcp_pyld_len + ntohl(tcp->seq);
7873 lro->tcp_ack = ntohl(tcp->ack_seq);
7875 lro->total_len = ntohs(ip->tot_len);
7878 * check if we saw TCP timestamp. Other consistency checks have
7879 * already been done.
7881 if (tcp->doff == 8) {
7883 ptr = (u32 *)(tcp+1);
7885 lro->cur_tsval = *(ptr+1);
7886 lro->cur_tsecr = *(ptr+2);
7891 static void update_L3L4_header(struct s2io_nic *sp, struct lro *lro)
7893 struct iphdr *ip = lro->iph;
7894 struct tcphdr *tcp = lro->tcph;
7896 struct stat_block *statinfo = sp->mac_control.stats_info;
7897 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
7899 /* Update L3 header */
7900 ip->tot_len = htons(lro->total_len);
7902 nchk = ip_fast_csum((u8 *)lro->iph, ip->ihl);
7905 /* Update L4 header */
7906 tcp->ack_seq = lro->tcp_ack;
7907 tcp->window = lro->window;
7909 /* Update tsecr field if this session has timestamps enabled */
7911 u32 *ptr = (u32 *)(tcp + 1);
7912 *(ptr+2) = lro->cur_tsecr;
7915 /* Update counters required for calculation of
7916 * average no. of packets aggregated.
7918 statinfo->sw_stat.sum_avg_pkts_aggregated += lro->sg_num;
7919 statinfo->sw_stat.num_aggregations++;
7922 static void aggregate_new_rx(struct lro *lro, struct iphdr *ip,
7923 struct tcphdr *tcp, u32 l4_pyld)
7925 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
7926 lro->total_len += l4_pyld;
7927 lro->frags_len += l4_pyld;
7928 lro->tcp_next_seq += l4_pyld;
7931 /* Update ack seq no. and window ad(from this pkt) in LRO object */
7932 lro->tcp_ack = tcp->ack_seq;
7933 lro->window = tcp->window;
7937 /* Update tsecr and tsval from this packet */
7938 ptr = (u32 *) (tcp + 1);
7939 lro->cur_tsval = *(ptr + 1);
7940 lro->cur_tsecr = *(ptr + 2);
7944 static int verify_l3_l4_lro_capable(struct lro *l_lro, struct iphdr *ip,
7945 struct tcphdr *tcp, u32 tcp_pyld_len)
7949 DBG_PRINT(INFO_DBG,"%s: Been here...\n", __FUNCTION__);
7951 if (!tcp_pyld_len) {
7952 /* Runt frame or a pure ack */
7956 if (ip->ihl != 5) /* IP has options */
7959 /* If we see CE codepoint in IP header, packet is not mergeable */
7960 if (INET_ECN_is_ce(ipv4_get_dsfield(ip)))
7963 /* If we see ECE or CWR flags in TCP header, packet is not mergeable */
7964 if (tcp->urg || tcp->psh || tcp->rst || tcp->syn || tcp->fin ||
7965 tcp->ece || tcp->cwr || !tcp->ack) {
7967 * Currently recognize only the ack control word and
7968 * any other control field being set would result in
7969 * flushing the LRO session
7975 * Allow only one TCP timestamp option. Don't aggregate if
7976 * any other options are detected.
7978 if (tcp->doff != 5 && tcp->doff != 8)
7981 if (tcp->doff == 8) {
7982 ptr = (u8 *)(tcp + 1);
7983 while (*ptr == TCPOPT_NOP)
7985 if (*ptr != TCPOPT_TIMESTAMP || *(ptr+1) != TCPOLEN_TIMESTAMP)
7988 /* Ensure timestamp value increases monotonically */
7990 if (l_lro->cur_tsval > *((u32 *)(ptr+2)))
7993 /* timestamp echo reply should be non-zero */
7994 if (*((u32 *)(ptr+6)) == 0)
8002 s2io_club_tcp_session(u8 *buffer, u8 **tcp, u32 *tcp_len, struct lro **lro,
8003 struct RxD_t *rxdp, struct s2io_nic *sp)
8006 struct tcphdr *tcph;
8009 if (!(ret = check_L2_lro_capable(buffer, &ip, (struct tcphdr **)tcp,
8011 DBG_PRINT(INFO_DBG,"IP Saddr: %x Daddr: %x\n",
8012 ip->saddr, ip->daddr);
8017 tcph = (struct tcphdr *)*tcp;
8018 *tcp_len = get_l4_pyld_length(ip, tcph);
8019 for (i=0; i<MAX_LRO_SESSIONS; i++) {
8020 struct lro *l_lro = &sp->lro0_n[i];
8021 if (l_lro->in_use) {
8022 if (check_for_socket_match(l_lro, ip, tcph))
8024 /* Sock pair matched */
8027 if ((*lro)->tcp_next_seq != ntohl(tcph->seq)) {
8028 DBG_PRINT(INFO_DBG, "%s:Out of order. expected "
8029 "0x%x, actual 0x%x\n", __FUNCTION__,
8030 (*lro)->tcp_next_seq,
8033 sp->mac_control.stats_info->
8034 sw_stat.outof_sequence_pkts++;
8039 if (!verify_l3_l4_lro_capable(l_lro, ip, tcph,*tcp_len))
8040 ret = 1; /* Aggregate */
8042 ret = 2; /* Flush both */
8048 /* Before searching for available LRO objects,
8049 * check if the pkt is L3/L4 aggregatable. If not
8050 * don't create new LRO session. Just send this
8053 if (verify_l3_l4_lro_capable(NULL, ip, tcph, *tcp_len)) {
8057 for (i=0; i<MAX_LRO_SESSIONS; i++) {
8058 struct lro *l_lro = &sp->lro0_n[i];
8059 if (!(l_lro->in_use)) {
8061 ret = 3; /* Begin anew */
8067 if (ret == 0) { /* sessions exceeded */
8068 DBG_PRINT(INFO_DBG,"%s:All LRO sessions already in use\n",
8076 initiate_new_session(*lro, buffer, ip, tcph, *tcp_len);
8079 update_L3L4_header(sp, *lro);
8082 aggregate_new_rx(*lro, ip, tcph, *tcp_len);
8083 if ((*lro)->sg_num == sp->lro_max_aggr_per_sess) {
8084 update_L3L4_header(sp, *lro);
8085 ret = 4; /* Flush the LRO */
8089 DBG_PRINT(ERR_DBG,"%s:Dont know, can't say!!\n",
8097 static void clear_lro_session(struct lro *lro)
8099 static u16 lro_struct_size = sizeof(struct lro);
8101 memset(lro, 0, lro_struct_size);
8104 static void queue_rx_frame(struct sk_buff *skb)
8106 struct net_device *dev = skb->dev;
8108 skb->protocol = eth_type_trans(skb, dev);
8110 netif_receive_skb(skb);
8115 static void lro_append_pkt(struct s2io_nic *sp, struct lro *lro,
8116 struct sk_buff *skb,
8119 struct sk_buff *first = lro->parent;
8121 first->len += tcp_len;
8122 first->data_len = lro->frags_len;
8123 skb_pull(skb, (skb->len - tcp_len));
8124 if (skb_shinfo(first)->frag_list)
8125 lro->last_frag->next = skb;
8127 skb_shinfo(first)->frag_list = skb;
8128 first->truesize += skb->truesize;
8129 lro->last_frag = skb;
8130 sp->mac_control.stats_info->sw_stat.clubbed_frms_cnt++;
8135 * s2io_io_error_detected - called when PCI error is detected
8136 * @pdev: Pointer to PCI device
8137 * @state: The current pci connection state
8139 * This function is called after a PCI bus error affecting
8140 * this device has been detected.
8142 static pci_ers_result_t s2io_io_error_detected(struct pci_dev *pdev,
8143 pci_channel_state_t state)
8145 struct net_device *netdev = pci_get_drvdata(pdev);
8146 struct s2io_nic *sp = netdev->priv;
8148 netif_device_detach(netdev);
8150 if (netif_running(netdev)) {
8151 /* Bring down the card, while avoiding PCI I/O */
8152 do_s2io_card_down(sp, 0);
8154 pci_disable_device(pdev);
8156 return PCI_ERS_RESULT_NEED_RESET;
8160 * s2io_io_slot_reset - called after the pci bus has been reset.
8161 * @pdev: Pointer to PCI device
8163 * Restart the card from scratch, as if from a cold-boot.
8164 * At this point, the card has exprienced a hard reset,
8165 * followed by fixups by BIOS, and has its config space
8166 * set up identically to what it was at cold boot.
8168 static pci_ers_result_t s2io_io_slot_reset(struct pci_dev *pdev)
8170 struct net_device *netdev = pci_get_drvdata(pdev);
8171 struct s2io_nic *sp = netdev->priv;
8173 if (pci_enable_device(pdev)) {
8174 printk(KERN_ERR "s2io: "
8175 "Cannot re-enable PCI device after reset.\n");
8176 return PCI_ERS_RESULT_DISCONNECT;
8179 pci_set_master(pdev);
8182 return PCI_ERS_RESULT_RECOVERED;
8186 * s2io_io_resume - called when traffic can start flowing again.
8187 * @pdev: Pointer to PCI device
8189 * This callback is called when the error recovery driver tells
8190 * us that its OK to resume normal operation.
8192 static void s2io_io_resume(struct pci_dev *pdev)
8194 struct net_device *netdev = pci_get_drvdata(pdev);
8195 struct s2io_nic *sp = netdev->priv;
8197 if (netif_running(netdev)) {
8198 if (s2io_card_up(sp)) {
8199 printk(KERN_ERR "s2io: "
8200 "Can't bring device back up after reset.\n");
8204 if (s2io_set_mac_addr(netdev, netdev->dev_addr) == FAILURE) {
8206 printk(KERN_ERR "s2io: "
8207 "Can't resetore mac addr after reset.\n");
8212 netif_device_attach(netdev);
8213 netif_wake_queue(netdev);
git.openpandora.org / pandora-kernel.git / blob