1 /*******************************************************************************
3 Intel PRO/1000 Linux driver
4 Copyright(c) 1999 - 2008 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 Linux NICS <linux.nics@intel.com>
24 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
25 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
27 *******************************************************************************/
29 #include <linux/module.h>
30 #include <linux/types.h>
31 #include <linux/init.h>
32 #include <linux/pci.h>
33 #include <linux/vmalloc.h>
34 #include <linux/pagemap.h>
35 #include <linux/delay.h>
36 #include <linux/netdevice.h>
37 #include <linux/tcp.h>
38 #include <linux/ipv6.h>
39 #include <net/checksum.h>
40 #include <net/ip6_checksum.h>
41 #include <linux/mii.h>
42 #include <linux/ethtool.h>
43 #include <linux/if_vlan.h>
44 #include <linux/cpu.h>
45 #include <linux/smp.h>
46 #include <linux/pm_qos_params.h>
50 #define DRV_VERSION "0.3.3.3-k2"
51 char e1000e_driver_name[] = "e1000e";
52 const char e1000e_driver_version[] = DRV_VERSION;
54 static const struct e1000_info *e1000_info_tbl[] = {
55 [board_82571] = &e1000_82571_info,
56 [board_82572] = &e1000_82572_info,
57 [board_82573] = &e1000_82573_info,
58 [board_80003es2lan] = &e1000_es2_info,
59 [board_ich8lan] = &e1000_ich8_info,
60 [board_ich9lan] = &e1000_ich9_info,
65 * e1000_get_hw_dev_name - return device name string
66 * used by hardware layer to print debugging information
68 char *e1000e_get_hw_dev_name(struct e1000_hw *hw)
70 return hw->adapter->netdev->name;
75 * e1000_desc_unused - calculate if we have unused descriptors
77 static int e1000_desc_unused(struct e1000_ring *ring)
79 if (ring->next_to_clean > ring->next_to_use)
80 return ring->next_to_clean - ring->next_to_use - 1;
82 return ring->count + ring->next_to_clean - ring->next_to_use - 1;
86 * e1000_receive_skb - helper function to handle Rx indications
87 * @adapter: board private structure
88 * @status: descriptor status field as written by hardware
89 * @vlan: descriptor vlan field as written by hardware (no le/be conversion)
90 * @skb: pointer to sk_buff to be indicated to stack
92 static void e1000_receive_skb(struct e1000_adapter *adapter,
93 struct net_device *netdev,
95 u8 status, __le16 vlan)
97 skb->protocol = eth_type_trans(skb, netdev);
99 if (adapter->vlgrp && (status & E1000_RXD_STAT_VP))
100 vlan_hwaccel_receive_skb(skb, adapter->vlgrp,
103 netif_receive_skb(skb);
105 netdev->last_rx = jiffies;
109 * e1000_rx_checksum - Receive Checksum Offload for 82543
110 * @adapter: board private structure
111 * @status_err: receive descriptor status and error fields
112 * @csum: receive descriptor csum field
113 * @sk_buff: socket buffer with received data
115 static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
116 u32 csum, struct sk_buff *skb)
118 u16 status = (u16)status_err;
119 u8 errors = (u8)(status_err >> 24);
120 skb->ip_summed = CHECKSUM_NONE;
122 /* Ignore Checksum bit is set */
123 if (status & E1000_RXD_STAT_IXSM)
125 /* TCP/UDP checksum error bit is set */
126 if (errors & E1000_RXD_ERR_TCPE) {
127 /* let the stack verify checksum errors */
128 adapter->hw_csum_err++;
132 /* TCP/UDP Checksum has not been calculated */
133 if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS)))
136 /* It must be a TCP or UDP packet with a valid checksum */
137 if (status & E1000_RXD_STAT_TCPCS) {
138 /* TCP checksum is good */
139 skb->ip_summed = CHECKSUM_UNNECESSARY;
142 * IP fragment with UDP payload
143 * Hardware complements the payload checksum, so we undo it
144 * and then put the value in host order for further stack use.
146 __sum16 sum = (__force __sum16)htons(csum);
147 skb->csum = csum_unfold(~sum);
148 skb->ip_summed = CHECKSUM_COMPLETE;
150 adapter->hw_csum_good++;
154 * e1000_alloc_rx_buffers - Replace used receive buffers; legacy & extended
155 * @adapter: address of board private structure
157 static void e1000_alloc_rx_buffers(struct e1000_adapter *adapter,
160 struct net_device *netdev = adapter->netdev;
161 struct pci_dev *pdev = adapter->pdev;
162 struct e1000_ring *rx_ring = adapter->rx_ring;
163 struct e1000_rx_desc *rx_desc;
164 struct e1000_buffer *buffer_info;
167 unsigned int bufsz = adapter->rx_buffer_len + NET_IP_ALIGN;
169 i = rx_ring->next_to_use;
170 buffer_info = &rx_ring->buffer_info[i];
172 while (cleaned_count--) {
173 skb = buffer_info->skb;
179 skb = netdev_alloc_skb(netdev, bufsz);
181 /* Better luck next round */
182 adapter->alloc_rx_buff_failed++;
187 * Make buffer alignment 2 beyond a 16 byte boundary
188 * this will result in a 16 byte aligned IP header after
189 * the 14 byte MAC header is removed
191 skb_reserve(skb, NET_IP_ALIGN);
193 buffer_info->skb = skb;
195 buffer_info->dma = pci_map_single(pdev, skb->data,
196 adapter->rx_buffer_len,
198 if (pci_dma_mapping_error(buffer_info->dma)) {
199 dev_err(&pdev->dev, "RX DMA map failed\n");
200 adapter->rx_dma_failed++;
204 rx_desc = E1000_RX_DESC(*rx_ring, i);
205 rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
208 if (i == rx_ring->count)
210 buffer_info = &rx_ring->buffer_info[i];
213 if (rx_ring->next_to_use != i) {
214 rx_ring->next_to_use = i;
216 i = (rx_ring->count - 1);
219 * Force memory writes to complete before letting h/w
220 * know there are new descriptors to fetch. (Only
221 * applicable for weak-ordered memory model archs,
225 writel(i, adapter->hw.hw_addr + rx_ring->tail);
230 * e1000_alloc_rx_buffers_ps - Replace used receive buffers; packet split
231 * @adapter: address of board private structure
233 static void e1000_alloc_rx_buffers_ps(struct e1000_adapter *adapter,
236 struct net_device *netdev = adapter->netdev;
237 struct pci_dev *pdev = adapter->pdev;
238 union e1000_rx_desc_packet_split *rx_desc;
239 struct e1000_ring *rx_ring = adapter->rx_ring;
240 struct e1000_buffer *buffer_info;
241 struct e1000_ps_page *ps_page;
245 i = rx_ring->next_to_use;
246 buffer_info = &rx_ring->buffer_info[i];
248 while (cleaned_count--) {
249 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
251 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
252 ps_page = &buffer_info->ps_pages[j];
253 if (j >= adapter->rx_ps_pages) {
254 /* all unused desc entries get hw null ptr */
255 rx_desc->read.buffer_addr[j+1] = ~cpu_to_le64(0);
258 if (!ps_page->page) {
259 ps_page->page = alloc_page(GFP_ATOMIC);
260 if (!ps_page->page) {
261 adapter->alloc_rx_buff_failed++;
264 ps_page->dma = pci_map_page(pdev,
268 if (pci_dma_mapping_error(ps_page->dma)) {
269 dev_err(&adapter->pdev->dev,
270 "RX DMA page map failed\n");
271 adapter->rx_dma_failed++;
276 * Refresh the desc even if buffer_addrs
277 * didn't change because each write-back
280 rx_desc->read.buffer_addr[j+1] =
281 cpu_to_le64(ps_page->dma);
284 skb = netdev_alloc_skb(netdev,
285 adapter->rx_ps_bsize0 + NET_IP_ALIGN);
288 adapter->alloc_rx_buff_failed++;
293 * Make buffer alignment 2 beyond a 16 byte boundary
294 * this will result in a 16 byte aligned IP header after
295 * the 14 byte MAC header is removed
297 skb_reserve(skb, NET_IP_ALIGN);
299 buffer_info->skb = skb;
300 buffer_info->dma = pci_map_single(pdev, skb->data,
301 adapter->rx_ps_bsize0,
303 if (pci_dma_mapping_error(buffer_info->dma)) {
304 dev_err(&pdev->dev, "RX DMA map failed\n");
305 adapter->rx_dma_failed++;
307 dev_kfree_skb_any(skb);
308 buffer_info->skb = NULL;
312 rx_desc->read.buffer_addr[0] = cpu_to_le64(buffer_info->dma);
315 if (i == rx_ring->count)
317 buffer_info = &rx_ring->buffer_info[i];
321 if (rx_ring->next_to_use != i) {
322 rx_ring->next_to_use = i;
325 i = (rx_ring->count - 1);
328 * Force memory writes to complete before letting h/w
329 * know there are new descriptors to fetch. (Only
330 * applicable for weak-ordered memory model archs,
335 * Hardware increments by 16 bytes, but packet split
336 * descriptors are 32 bytes...so we increment tail
339 writel(i<<1, adapter->hw.hw_addr + rx_ring->tail);
344 * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers
345 * @adapter: address of board private structure
346 * @rx_ring: pointer to receive ring structure
347 * @cleaned_count: number of buffers to allocate this pass
350 static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter,
353 struct net_device *netdev = adapter->netdev;
354 struct pci_dev *pdev = adapter->pdev;
355 struct e1000_rx_desc *rx_desc;
356 struct e1000_ring *rx_ring = adapter->rx_ring;
357 struct e1000_buffer *buffer_info;
360 unsigned int bufsz = 256 -
361 16 /* for skb_reserve */ -
364 i = rx_ring->next_to_use;
365 buffer_info = &rx_ring->buffer_info[i];
367 while (cleaned_count--) {
368 skb = buffer_info->skb;
374 skb = netdev_alloc_skb(netdev, bufsz);
375 if (unlikely(!skb)) {
376 /* Better luck next round */
377 adapter->alloc_rx_buff_failed++;
381 /* Make buffer alignment 2 beyond a 16 byte boundary
382 * this will result in a 16 byte aligned IP header after
383 * the 14 byte MAC header is removed
385 skb_reserve(skb, NET_IP_ALIGN);
387 buffer_info->skb = skb;
389 /* allocate a new page if necessary */
390 if (!buffer_info->page) {
391 buffer_info->page = alloc_page(GFP_ATOMIC);
392 if (unlikely(!buffer_info->page)) {
393 adapter->alloc_rx_buff_failed++;
398 if (!buffer_info->dma)
399 buffer_info->dma = pci_map_page(pdev,
400 buffer_info->page, 0,
404 rx_desc = E1000_RX_DESC(*rx_ring, i);
405 rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
407 if (unlikely(++i == rx_ring->count))
409 buffer_info = &rx_ring->buffer_info[i];
412 if (likely(rx_ring->next_to_use != i)) {
413 rx_ring->next_to_use = i;
414 if (unlikely(i-- == 0))
415 i = (rx_ring->count - 1);
417 /* Force memory writes to complete before letting h/w
418 * know there are new descriptors to fetch. (Only
419 * applicable for weak-ordered memory model archs,
422 writel(i, adapter->hw.hw_addr + rx_ring->tail);
427 * e1000_clean_rx_irq - Send received data up the network stack; legacy
428 * @adapter: board private structure
430 * the return value indicates whether actual cleaning was done, there
431 * is no guarantee that everything was cleaned
433 static bool e1000_clean_rx_irq(struct e1000_adapter *adapter,
434 int *work_done, int work_to_do)
436 struct net_device *netdev = adapter->netdev;
437 struct pci_dev *pdev = adapter->pdev;
438 struct e1000_ring *rx_ring = adapter->rx_ring;
439 struct e1000_rx_desc *rx_desc, *next_rxd;
440 struct e1000_buffer *buffer_info, *next_buffer;
443 int cleaned_count = 0;
445 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
447 i = rx_ring->next_to_clean;
448 rx_desc = E1000_RX_DESC(*rx_ring, i);
449 buffer_info = &rx_ring->buffer_info[i];
451 while (rx_desc->status & E1000_RXD_STAT_DD) {
455 if (*work_done >= work_to_do)
459 status = rx_desc->status;
460 skb = buffer_info->skb;
461 buffer_info->skb = NULL;
463 prefetch(skb->data - NET_IP_ALIGN);
466 if (i == rx_ring->count)
468 next_rxd = E1000_RX_DESC(*rx_ring, i);
471 next_buffer = &rx_ring->buffer_info[i];
475 pci_unmap_single(pdev,
477 adapter->rx_buffer_len,
479 buffer_info->dma = 0;
481 length = le16_to_cpu(rx_desc->length);
483 /* !EOP means multiple descriptors were used to store a single
484 * packet, also make sure the frame isn't just CRC only */
485 if (!(status & E1000_RXD_STAT_EOP) || (length <= 4)) {
486 /* All receives must fit into a single buffer */
487 ndev_dbg(netdev, "%s: Receive packet consumed "
488 "multiple buffers\n", netdev->name);
490 buffer_info->skb = skb;
494 if (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK) {
496 buffer_info->skb = skb;
500 total_rx_bytes += length;
504 * code added for copybreak, this should improve
505 * performance for small packets with large amounts
506 * of reassembly being done in the stack
508 if (length < copybreak) {
509 struct sk_buff *new_skb =
510 netdev_alloc_skb(netdev, length + NET_IP_ALIGN);
512 skb_reserve(new_skb, NET_IP_ALIGN);
513 memcpy(new_skb->data - NET_IP_ALIGN,
514 skb->data - NET_IP_ALIGN,
515 length + NET_IP_ALIGN);
516 /* save the skb in buffer_info as good */
517 buffer_info->skb = skb;
520 /* else just continue with the old one */
522 /* end copybreak code */
523 skb_put(skb, length);
525 /* Receive Checksum Offload */
526 e1000_rx_checksum(adapter,
528 ((u32)(rx_desc->errors) << 24),
529 le16_to_cpu(rx_desc->csum), skb);
531 e1000_receive_skb(adapter, netdev, skb,status,rx_desc->special);
536 /* return some buffers to hardware, one at a time is too slow */
537 if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
538 adapter->alloc_rx_buf(adapter, cleaned_count);
542 /* use prefetched values */
544 buffer_info = next_buffer;
546 rx_ring->next_to_clean = i;
548 cleaned_count = e1000_desc_unused(rx_ring);
550 adapter->alloc_rx_buf(adapter, cleaned_count);
552 adapter->total_rx_bytes += total_rx_bytes;
553 adapter->total_rx_packets += total_rx_packets;
554 adapter->net_stats.rx_bytes += total_rx_bytes;
555 adapter->net_stats.rx_packets += total_rx_packets;
559 static void e1000_put_txbuf(struct e1000_adapter *adapter,
560 struct e1000_buffer *buffer_info)
562 if (buffer_info->dma) {
563 pci_unmap_page(adapter->pdev, buffer_info->dma,
564 buffer_info->length, PCI_DMA_TODEVICE);
565 buffer_info->dma = 0;
567 if (buffer_info->skb) {
568 dev_kfree_skb_any(buffer_info->skb);
569 buffer_info->skb = NULL;
573 static void e1000_print_tx_hang(struct e1000_adapter *adapter)
575 struct e1000_ring *tx_ring = adapter->tx_ring;
576 unsigned int i = tx_ring->next_to_clean;
577 unsigned int eop = tx_ring->buffer_info[i].next_to_watch;
578 struct e1000_tx_desc *eop_desc = E1000_TX_DESC(*tx_ring, eop);
579 struct net_device *netdev = adapter->netdev;
581 /* detected Tx unit hang */
583 "Detected Tx Unit Hang:\n"
586 " next_to_use <%x>\n"
587 " next_to_clean <%x>\n"
588 "buffer_info[next_to_clean]:\n"
589 " time_stamp <%lx>\n"
590 " next_to_watch <%x>\n"
592 " next_to_watch.status <%x>\n",
593 readl(adapter->hw.hw_addr + tx_ring->head),
594 readl(adapter->hw.hw_addr + tx_ring->tail),
595 tx_ring->next_to_use,
596 tx_ring->next_to_clean,
597 tx_ring->buffer_info[eop].time_stamp,
600 eop_desc->upper.fields.status);
604 * e1000_clean_tx_irq - Reclaim resources after transmit completes
605 * @adapter: board private structure
607 * the return value indicates whether actual cleaning was done, there
608 * is no guarantee that everything was cleaned
610 static bool e1000_clean_tx_irq(struct e1000_adapter *adapter)
612 struct net_device *netdev = adapter->netdev;
613 struct e1000_hw *hw = &adapter->hw;
614 struct e1000_ring *tx_ring = adapter->tx_ring;
615 struct e1000_tx_desc *tx_desc, *eop_desc;
616 struct e1000_buffer *buffer_info;
618 unsigned int count = 0;
620 unsigned int total_tx_bytes = 0, total_tx_packets = 0;
622 i = tx_ring->next_to_clean;
623 eop = tx_ring->buffer_info[i].next_to_watch;
624 eop_desc = E1000_TX_DESC(*tx_ring, eop);
626 while (eop_desc->upper.data & cpu_to_le32(E1000_TXD_STAT_DD)) {
627 for (cleaned = 0; !cleaned; ) {
628 tx_desc = E1000_TX_DESC(*tx_ring, i);
629 buffer_info = &tx_ring->buffer_info[i];
630 cleaned = (i == eop);
633 struct sk_buff *skb = buffer_info->skb;
634 unsigned int segs, bytecount;
635 segs = skb_shinfo(skb)->gso_segs ?: 1;
636 /* multiply data chunks by size of headers */
637 bytecount = ((segs - 1) * skb_headlen(skb)) +
639 total_tx_packets += segs;
640 total_tx_bytes += bytecount;
643 e1000_put_txbuf(adapter, buffer_info);
644 tx_desc->upper.data = 0;
647 if (i == tx_ring->count)
651 eop = tx_ring->buffer_info[i].next_to_watch;
652 eop_desc = E1000_TX_DESC(*tx_ring, eop);
653 #define E1000_TX_WEIGHT 64
654 /* weight of a sort for tx, to avoid endless transmit cleanup */
655 if (count++ == E1000_TX_WEIGHT)
659 tx_ring->next_to_clean = i;
661 #define TX_WAKE_THRESHOLD 32
662 if (cleaned && netif_carrier_ok(netdev) &&
663 e1000_desc_unused(tx_ring) >= TX_WAKE_THRESHOLD) {
664 /* Make sure that anybody stopping the queue after this
665 * sees the new next_to_clean.
669 if (netif_queue_stopped(netdev) &&
670 !(test_bit(__E1000_DOWN, &adapter->state))) {
671 netif_wake_queue(netdev);
672 ++adapter->restart_queue;
676 if (adapter->detect_tx_hung) {
678 * Detect a transmit hang in hardware, this serializes the
679 * check with the clearing of time_stamp and movement of i
681 adapter->detect_tx_hung = 0;
682 if (tx_ring->buffer_info[eop].dma &&
683 time_after(jiffies, tx_ring->buffer_info[eop].time_stamp
684 + (adapter->tx_timeout_factor * HZ))
685 && !(er32(STATUS) & E1000_STATUS_TXOFF)) {
686 e1000_print_tx_hang(adapter);
687 netif_stop_queue(netdev);
690 adapter->total_tx_bytes += total_tx_bytes;
691 adapter->total_tx_packets += total_tx_packets;
692 adapter->net_stats.tx_bytes += total_tx_bytes;
693 adapter->net_stats.tx_packets += total_tx_packets;
698 * e1000_clean_rx_irq_ps - Send received data up the network stack; packet split
699 * @adapter: board private structure
701 * the return value indicates whether actual cleaning was done, there
702 * is no guarantee that everything was cleaned
704 static bool e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
705 int *work_done, int work_to_do)
707 union e1000_rx_desc_packet_split *rx_desc, *next_rxd;
708 struct net_device *netdev = adapter->netdev;
709 struct pci_dev *pdev = adapter->pdev;
710 struct e1000_ring *rx_ring = adapter->rx_ring;
711 struct e1000_buffer *buffer_info, *next_buffer;
712 struct e1000_ps_page *ps_page;
716 int cleaned_count = 0;
718 unsigned int total_rx_bytes = 0, total_rx_packets = 0;
720 i = rx_ring->next_to_clean;
721 rx_desc = E1000_RX_DESC_PS(*rx_ring, i);
722 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
723 buffer_info = &rx_ring->buffer_info[i];
725 while (staterr & E1000_RXD_STAT_DD) {
726 if (*work_done >= work_to_do)
729 skb = buffer_info->skb;
731 /* in the packet split case this is header only */
732 prefetch(skb->data - NET_IP_ALIGN);
735 if (i == rx_ring->count)
737 next_rxd = E1000_RX_DESC_PS(*rx_ring, i);
740 next_buffer = &rx_ring->buffer_info[i];
744 pci_unmap_single(pdev, buffer_info->dma,
745 adapter->rx_ps_bsize0,
747 buffer_info->dma = 0;
749 if (!(staterr & E1000_RXD_STAT_EOP)) {
750 ndev_dbg(netdev, "%s: Packet Split buffers didn't pick "
751 "up the full packet\n", netdev->name);
752 dev_kfree_skb_irq(skb);
756 if (staterr & E1000_RXDEXT_ERR_FRAME_ERR_MASK) {
757 dev_kfree_skb_irq(skb);
761 length = le16_to_cpu(rx_desc->wb.middle.length0);
764 ndev_dbg(netdev, "%s: Last part of the packet spanning"
765 " multiple descriptors\n", netdev->name);
766 dev_kfree_skb_irq(skb);
771 skb_put(skb, length);
775 * this looks ugly, but it seems compiler issues make it
776 * more efficient than reusing j
778 int l1 = le16_to_cpu(rx_desc->wb.upper.length[0]);
781 * page alloc/put takes too long and effects small packet
782 * throughput, so unsplit small packets and save the alloc/put
783 * only valid in softirq (napi) context to call kmap_*
785 if (l1 && (l1 <= copybreak) &&
786 ((length + l1) <= adapter->rx_ps_bsize0)) {
789 ps_page = &buffer_info->ps_pages[0];
792 * there is no documentation about how to call
793 * kmap_atomic, so we can't hold the mapping
796 pci_dma_sync_single_for_cpu(pdev, ps_page->dma,
797 PAGE_SIZE, PCI_DMA_FROMDEVICE);
798 vaddr = kmap_atomic(ps_page->page, KM_SKB_DATA_SOFTIRQ);
799 memcpy(skb_tail_pointer(skb), vaddr, l1);
800 kunmap_atomic(vaddr, KM_SKB_DATA_SOFTIRQ);
801 pci_dma_sync_single_for_device(pdev, ps_page->dma,
802 PAGE_SIZE, PCI_DMA_FROMDEVICE);
809 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
810 length = le16_to_cpu(rx_desc->wb.upper.length[j]);
814 ps_page = &buffer_info->ps_pages[j];
815 pci_unmap_page(pdev, ps_page->dma, PAGE_SIZE,
818 skb_fill_page_desc(skb, j, ps_page->page, 0, length);
819 ps_page->page = NULL;
821 skb->data_len += length;
822 skb->truesize += length;
826 total_rx_bytes += skb->len;
829 e1000_rx_checksum(adapter, staterr, le16_to_cpu(
830 rx_desc->wb.lower.hi_dword.csum_ip.csum), skb);
832 if (rx_desc->wb.upper.header_status &
833 cpu_to_le16(E1000_RXDPS_HDRSTAT_HDRSP))
834 adapter->rx_hdr_split++;
836 e1000_receive_skb(adapter, netdev, skb,
837 staterr, rx_desc->wb.middle.vlan);
840 rx_desc->wb.middle.status_error &= cpu_to_le32(~0xFF);
841 buffer_info->skb = NULL;
843 /* return some buffers to hardware, one at a time is too slow */
844 if (cleaned_count >= E1000_RX_BUFFER_WRITE) {
845 adapter->alloc_rx_buf(adapter, cleaned_count);
849 /* use prefetched values */
851 buffer_info = next_buffer;
853 staterr = le32_to_cpu(rx_desc->wb.middle.status_error);
855 rx_ring->next_to_clean = i;
857 cleaned_count = e1000_desc_unused(rx_ring);
859 adapter->alloc_rx_buf(adapter, cleaned_count);
861 adapter->total_rx_bytes += total_rx_bytes;
862 adapter->total_rx_packets += total_rx_packets;
863 adapter->net_stats.rx_bytes += total_rx_bytes;
864 adapter->net_stats.rx_packets += total_rx_packets;
869 * e1000_consume_page - helper function
871 static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb,
876 skb->data_len += length;
877 skb->truesize += length;
881 * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy
882 * @adapter: board private structure
884 * the return value indicates whether actual cleaning was done, there
885 * is no guarantee that everything was cleaned
888 static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter,
889 int *work_done, int work_to_do)
891 struct net_device *netdev = adapter->netdev;
892 struct pci_dev *pdev = adapter->pdev;
893 struct e1000_ring *rx_ring = adapter->rx_ring;
894 struct e1000_rx_desc *rx_desc, *next_rxd;
895 struct e1000_buffer *buffer_info, *next_buffer;
898 int cleaned_count = 0;
899 bool cleaned = false;
900 unsigned int total_rx_bytes=0, total_rx_packets=0;
902 i = rx_ring->next_to_clean;
903 rx_desc = E1000_RX_DESC(*rx_ring, i);
904 buffer_info = &rx_ring->buffer_info[i];
906 while (rx_desc->status & E1000_RXD_STAT_DD) {
910 if (*work_done >= work_to_do)
914 status = rx_desc->status;
915 skb = buffer_info->skb;
916 buffer_info->skb = NULL;
919 if (i == rx_ring->count)
921 next_rxd = E1000_RX_DESC(*rx_ring, i);
924 next_buffer = &rx_ring->buffer_info[i];
928 pci_unmap_page(pdev, buffer_info->dma, PAGE_SIZE,
930 buffer_info->dma = 0;
932 length = le16_to_cpu(rx_desc->length);
934 /* errors is only valid for DD + EOP descriptors */
935 if (unlikely((status & E1000_RXD_STAT_EOP) &&
936 (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) {
937 /* recycle both page and skb */
938 buffer_info->skb = skb;
939 /* an error means any chain goes out the window
941 if (rx_ring->rx_skb_top)
942 dev_kfree_skb(rx_ring->rx_skb_top);
943 rx_ring->rx_skb_top = NULL;
947 #define rxtop rx_ring->rx_skb_top
948 if (!(status & E1000_RXD_STAT_EOP)) {
949 /* this descriptor is only the beginning (or middle) */
951 /* this is the beginning of a chain */
953 skb_fill_page_desc(rxtop, 0, buffer_info->page,
956 /* this is the middle of a chain */
957 skb_fill_page_desc(rxtop,
958 skb_shinfo(rxtop)->nr_frags,
959 buffer_info->page, 0, length);
960 /* re-use the skb, only consumed the page */
961 buffer_info->skb = skb;
963 e1000_consume_page(buffer_info, rxtop, length);
967 /* end of the chain */
968 skb_fill_page_desc(rxtop,
969 skb_shinfo(rxtop)->nr_frags,
970 buffer_info->page, 0, length);
971 /* re-use the current skb, we only consumed the
973 buffer_info->skb = skb;
976 e1000_consume_page(buffer_info, skb, length);
978 /* no chain, got EOP, this buf is the packet
979 * copybreak to save the put_page/alloc_page */
980 if (length <= copybreak &&
981 skb_tailroom(skb) >= length) {
983 vaddr = kmap_atomic(buffer_info->page,
984 KM_SKB_DATA_SOFTIRQ);
985 memcpy(skb_tail_pointer(skb), vaddr,
988 KM_SKB_DATA_SOFTIRQ);
989 /* re-use the page, so don't erase
990 * buffer_info->page */
991 skb_put(skb, length);
993 skb_fill_page_desc(skb, 0,
994 buffer_info->page, 0,
996 e1000_consume_page(buffer_info, skb,
1002 /* Receive Checksum Offload XXX recompute due to CRC strip? */
1003 e1000_rx_checksum(adapter,
1005 ((u32)(rx_desc->errors) << 24),
1006 le16_to_cpu(rx_desc->csum), skb);
1008 /* probably a little skewed due to removing CRC */
1009 total_rx_bytes += skb->len;
1012 /* eth type trans needs skb->data to point to something */
1013 if (!pskb_may_pull(skb, ETH_HLEN)) {
1014 ndev_err(netdev, "pskb_may_pull failed.\n");
1019 e1000_receive_skb(adapter, netdev, skb, status,
1023 rx_desc->status = 0;
1025 /* return some buffers to hardware, one at a time is too slow */
1026 if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) {
1027 adapter->alloc_rx_buf(adapter, cleaned_count);
1031 /* use prefetched values */
1033 buffer_info = next_buffer;
1035 rx_ring->next_to_clean = i;
1037 cleaned_count = e1000_desc_unused(rx_ring);
1039 adapter->alloc_rx_buf(adapter, cleaned_count);
1041 adapter->total_rx_bytes += total_rx_bytes;
1042 adapter->total_rx_packets += total_rx_packets;
1043 adapter->net_stats.rx_bytes += total_rx_bytes;
1044 adapter->net_stats.rx_packets += total_rx_packets;
1049 * e1000_clean_rx_ring - Free Rx Buffers per Queue
1050 * @adapter: board private structure
1052 static void e1000_clean_rx_ring(struct e1000_adapter *adapter)
1054 struct e1000_ring *rx_ring = adapter->rx_ring;
1055 struct e1000_buffer *buffer_info;
1056 struct e1000_ps_page *ps_page;
1057 struct pci_dev *pdev = adapter->pdev;
1060 /* Free all the Rx ring sk_buffs */
1061 for (i = 0; i < rx_ring->count; i++) {
1062 buffer_info = &rx_ring->buffer_info[i];
1063 if (buffer_info->dma) {
1064 if (adapter->clean_rx == e1000_clean_rx_irq)
1065 pci_unmap_single(pdev, buffer_info->dma,
1066 adapter->rx_buffer_len,
1067 PCI_DMA_FROMDEVICE);
1068 else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq)
1069 pci_unmap_page(pdev, buffer_info->dma,
1071 PCI_DMA_FROMDEVICE);
1072 else if (adapter->clean_rx == e1000_clean_rx_irq_ps)
1073 pci_unmap_single(pdev, buffer_info->dma,
1074 adapter->rx_ps_bsize0,
1075 PCI_DMA_FROMDEVICE);
1076 buffer_info->dma = 0;
1079 if (buffer_info->page) {
1080 put_page(buffer_info->page);
1081 buffer_info->page = NULL;
1084 if (buffer_info->skb) {
1085 dev_kfree_skb(buffer_info->skb);
1086 buffer_info->skb = NULL;
1089 for (j = 0; j < PS_PAGE_BUFFERS; j++) {
1090 ps_page = &buffer_info->ps_pages[j];
1093 pci_unmap_page(pdev, ps_page->dma, PAGE_SIZE,
1094 PCI_DMA_FROMDEVICE);
1096 put_page(ps_page->page);
1097 ps_page->page = NULL;
1101 /* there also may be some cached data from a chained receive */
1102 if (rx_ring->rx_skb_top) {
1103 dev_kfree_skb(rx_ring->rx_skb_top);
1104 rx_ring->rx_skb_top = NULL;
1107 /* Zero out the descriptor ring */
1108 memset(rx_ring->desc, 0, rx_ring->size);
1110 rx_ring->next_to_clean = 0;
1111 rx_ring->next_to_use = 0;
1113 writel(0, adapter->hw.hw_addr + rx_ring->head);
1114 writel(0, adapter->hw.hw_addr + rx_ring->tail);
1118 * e1000_intr_msi - Interrupt Handler
1119 * @irq: interrupt number
1120 * @data: pointer to a network interface device structure
1122 static irqreturn_t e1000_intr_msi(int irq, void *data)
1124 struct net_device *netdev = data;
1125 struct e1000_adapter *adapter = netdev_priv(netdev);
1126 struct e1000_hw *hw = &adapter->hw;
1127 u32 icr = er32(ICR);
1130 * read ICR disables interrupts using IAM
1133 if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
1134 hw->mac.get_link_status = 1;
1136 * ICH8 workaround-- Call gig speed drop workaround on cable
1137 * disconnect (LSC) before accessing any PHY registers
1139 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
1140 (!(er32(STATUS) & E1000_STATUS_LU)))
1141 e1000e_gig_downshift_workaround_ich8lan(hw);
1144 * 80003ES2LAN workaround-- For packet buffer work-around on
1145 * link down event; disable receives here in the ISR and reset
1146 * adapter in watchdog
1148 if (netif_carrier_ok(netdev) &&
1149 adapter->flags & FLAG_RX_NEEDS_RESTART) {
1150 /* disable receives */
1151 u32 rctl = er32(RCTL);
1152 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1153 adapter->flags |= FLAG_RX_RESTART_NOW;
1155 /* guard against interrupt when we're going down */
1156 if (!test_bit(__E1000_DOWN, &adapter->state))
1157 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1160 if (netif_rx_schedule_prep(netdev, &adapter->napi)) {
1161 adapter->total_tx_bytes = 0;
1162 adapter->total_tx_packets = 0;
1163 adapter->total_rx_bytes = 0;
1164 adapter->total_rx_packets = 0;
1165 __netif_rx_schedule(netdev, &adapter->napi);
1172 * e1000_intr - Interrupt Handler
1173 * @irq: interrupt number
1174 * @data: pointer to a network interface device structure
1176 static irqreturn_t e1000_intr(int irq, void *data)
1178 struct net_device *netdev = data;
1179 struct e1000_adapter *adapter = netdev_priv(netdev);
1180 struct e1000_hw *hw = &adapter->hw;
1182 u32 rctl, icr = er32(ICR);
1184 return IRQ_NONE; /* Not our interrupt */
1187 * IMS will not auto-mask if INT_ASSERTED is not set, and if it is
1188 * not set, then the adapter didn't send an interrupt
1190 if (!(icr & E1000_ICR_INT_ASSERTED))
1194 * Interrupt Auto-Mask...upon reading ICR,
1195 * interrupts are masked. No need for the
1199 if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) {
1200 hw->mac.get_link_status = 1;
1202 * ICH8 workaround-- Call gig speed drop workaround on cable
1203 * disconnect (LSC) before accessing any PHY registers
1205 if ((adapter->flags & FLAG_LSC_GIG_SPEED_DROP) &&
1206 (!(er32(STATUS) & E1000_STATUS_LU)))
1207 e1000e_gig_downshift_workaround_ich8lan(hw);
1210 * 80003ES2LAN workaround--
1211 * For packet buffer work-around on link down event;
1212 * disable receives here in the ISR and
1213 * reset adapter in watchdog
1215 if (netif_carrier_ok(netdev) &&
1216 (adapter->flags & FLAG_RX_NEEDS_RESTART)) {
1217 /* disable receives */
1219 ew32(RCTL, rctl & ~E1000_RCTL_EN);
1220 adapter->flags |= FLAG_RX_RESTART_NOW;
1222 /* guard against interrupt when we're going down */
1223 if (!test_bit(__E1000_DOWN, &adapter->state))
1224 mod_timer(&adapter->watchdog_timer, jiffies + 1);
1227 if (netif_rx_schedule_prep(netdev, &adapter->napi)) {
1228 adapter->total_tx_bytes = 0;
1229 adapter->total_tx_packets = 0;
1230 adapter->total_rx_bytes = 0;
1231 adapter->total_rx_packets = 0;
1232 __netif_rx_schedule(netdev, &adapter->napi);
1238 static int e1000_request_irq(struct e1000_adapter *adapter)
1240 struct net_device *netdev = adapter->netdev;
1241 irq_handler_t handler = e1000_intr;
1242 int irq_flags = IRQF_SHARED;
1245 if (!pci_enable_msi(adapter->pdev)) {
1246 adapter->flags |= FLAG_MSI_ENABLED;
1247 handler = e1000_intr_msi;
1251 err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name,
1255 "Unable to allocate %s interrupt (return: %d)\n",
1256 adapter->flags & FLAG_MSI_ENABLED ? "MSI":"INTx",
1258 if (adapter->flags & FLAG_MSI_ENABLED)
1259 pci_disable_msi(adapter->pdev);
1265 static void e1000_free_irq(struct e1000_adapter *adapter)
1267 struct net_device *netdev = adapter->netdev;
1269 free_irq(adapter->pdev->irq, netdev);
1270 if (adapter->flags & FLAG_MSI_ENABLED) {
1271 pci_disable_msi(adapter->pdev);
1272 adapter->flags &= ~FLAG_MSI_ENABLED;
1277 * e1000_irq_disable - Mask off interrupt generation on the NIC
1279 static void e1000_irq_disable(struct e1000_adapter *adapter)
1281 struct e1000_hw *hw = &adapter->hw;
1285 synchronize_irq(adapter->pdev->irq);
1289 * e1000_irq_enable - Enable default interrupt generation settings
1291 static void e1000_irq_enable(struct e1000_adapter *adapter)
1293 struct e1000_hw *hw = &adapter->hw;
1295 ew32(IMS, IMS_ENABLE_MASK);
1300 * e1000_get_hw_control - get control of the h/w from f/w
1301 * @adapter: address of board private structure
1303 * e1000_get_hw_control sets {CTRL_EXT|SWSM}:DRV_LOAD bit.
1304 * For ASF and Pass Through versions of f/w this means that
1305 * the driver is loaded. For AMT version (only with 82573)
1306 * of the f/w this means that the network i/f is open.
1308 static void e1000_get_hw_control(struct e1000_adapter *adapter)
1310 struct e1000_hw *hw = &adapter->hw;
1314 /* Let firmware know the driver has taken over */
1315 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
1317 ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD);
1318 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
1319 ctrl_ext = er32(CTRL_EXT);
1320 ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD);
1325 * e1000_release_hw_control - release control of the h/w to f/w
1326 * @adapter: address of board private structure
1328 * e1000_release_hw_control resets {CTRL_EXT|SWSM}:DRV_LOAD bit.
1329 * For ASF and Pass Through versions of f/w this means that the
1330 * driver is no longer loaded. For AMT version (only with 82573) i
1331 * of the f/w this means that the network i/f is closed.
1334 static void e1000_release_hw_control(struct e1000_adapter *adapter)
1336 struct e1000_hw *hw = &adapter->hw;
1340 /* Let firmware taken over control of h/w */
1341 if (adapter->flags & FLAG_HAS_SWSM_ON_LOAD) {
1343 ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD);
1344 } else if (adapter->flags & FLAG_HAS_CTRLEXT_ON_LOAD) {
1345 ctrl_ext = er32(CTRL_EXT);
1346 ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD);
1351 * @e1000_alloc_ring - allocate memory for a ring structure
1353 static int e1000_alloc_ring_dma(struct e1000_adapter *adapter,
1354 struct e1000_ring *ring)
1356 struct pci_dev *pdev = adapter->pdev;
1358 ring->desc = dma_alloc_coherent(&pdev->dev, ring->size, &ring->dma,
1367 * e1000e_setup_tx_resources - allocate Tx resources (Descriptors)
1368 * @adapter: board private structure
1370 * Return 0 on success, negative on failure
1372 int e1000e_setup_tx_resources(struct e1000_adapter *adapter)
1374 struct e1000_ring *tx_ring = adapter->tx_ring;
1375 int err = -ENOMEM, size;
1377 size = sizeof(struct e1000_buffer) * tx_ring->count;
1378 tx_ring->buffer_info = vmalloc(size);
1379 if (!tx_ring->buffer_info)
1381 memset(tx_ring->buffer_info, 0, size);
1383 /* round up to nearest 4K */
1384 tx_ring->size = tx_ring->count * sizeof(struct e1000_tx_desc);
1385 tx_ring->size = ALIGN(tx_ring->size, 4096);
1387 err = e1000_alloc_ring_dma(adapter, tx_ring);
1391 tx_ring->next_to_use = 0;
1392 tx_ring->next_to_clean = 0;
1393 spin_lock_init(&adapter->tx_queue_lock);
1397 vfree(tx_ring->buffer_info);
1398 ndev_err(adapter->netdev,
1399 "Unable to allocate memory for the transmit descriptor ring\n");
1404 * e1000e_setup_rx_resources - allocate Rx resources (Descriptors)
1405 * @adapter: board private structure
1407 * Returns 0 on success, negative on failure
1409 int e1000e_setup_rx_resources(struct e1000_adapter *adapter)
1411 struct e1000_ring *rx_ring = adapter->rx_ring;
1412 struct e1000_buffer *buffer_info;
1413 int i, size, desc_len, err = -ENOMEM;
1415 size = sizeof(struct e1000_buffer) * rx_ring->count;
1416 rx_ring->buffer_info = vmalloc(size);
1417 if (!rx_ring->buffer_info)
1419 memset(rx_ring->buffer_info, 0, size);
1421 for (i = 0; i < rx_ring->count; i++) {
1422 buffer_info = &rx_ring->buffer_info[i];
1423 buffer_info->ps_pages = kcalloc(PS_PAGE_BUFFERS,
1424 sizeof(struct e1000_ps_page),
1426 if (!buffer_info->ps_pages)
1430 desc_len = sizeof(union e1000_rx_desc_packet_split);
1432 /* Round up to nearest 4K */
1433 rx_ring->size = rx_ring->count * desc_len;
1434 rx_ring->size = ALIGN(rx_ring->size, 4096);
1436 err = e1000_alloc_ring_dma(adapter, rx_ring);
1440 rx_ring->next_to_clean = 0;
1441 rx_ring->next_to_use = 0;
1442 rx_ring->rx_skb_top = NULL;
1447 for (i = 0; i < rx_ring->count; i++) {
1448 buffer_info = &rx_ring->buffer_info[i];
1449 kfree(buffer_info->ps_pages);
1452 vfree(rx_ring->buffer_info);
1453 ndev_err(adapter->netdev,
1454 "Unable to allocate memory for the transmit descriptor ring\n");
1459 * e1000_clean_tx_ring - Free Tx Buffers
1460 * @adapter: board private structure
1462 static void e1000_clean_tx_ring(struct e1000_adapter *adapter)
1464 struct e1000_ring *tx_ring = adapter->tx_ring;
1465 struct e1000_buffer *buffer_info;
1469 for (i = 0; i < tx_ring->count; i++) {
1470 buffer_info = &tx_ring->buffer_info[i];
1471 e1000_put_txbuf(adapter, buffer_info);
1474 size = sizeof(struct e1000_buffer) * tx_ring->count;
1475 memset(tx_ring->buffer_info, 0, size);
1477 memset(tx_ring->desc, 0, tx_ring->size);
1479 tx_ring->next_to_use = 0;
1480 tx_ring->next_to_clean = 0;
1482 writel(0, adapter->hw.hw_addr + tx_ring->head);
1483 writel(0, adapter->hw.hw_addr + tx_ring->tail);
1487 * e1000e_free_tx_resources - Free Tx Resources per Queue
1488 * @adapter: board private structure
1490 * Free all transmit software resources
1492 void e1000e_free_tx_resources(struct e1000_adapter *adapter)
1494 struct pci_dev *pdev = adapter->pdev;
1495 struct e1000_ring *tx_ring = adapter->tx_ring;
1497 e1000_clean_tx_ring(adapter);
1499 vfree(tx_ring->buffer_info);
1500 tx_ring->buffer_info = NULL;
1502 dma_free_coherent(&pdev->dev, tx_ring->size, tx_ring->desc,
1504 tx_ring->desc = NULL;
1508 * e1000e_free_rx_resources - Free Rx Resources
1509 * @adapter: board private structure
1511 * Free all receive software resources
1514 void e1000e_free_rx_resources(struct e1000_adapter *adapter)
1516 struct pci_dev *pdev = adapter->pdev;
1517 struct e1000_ring *rx_ring = adapter->rx_ring;
1520 e1000_clean_rx_ring(adapter);
1522 for (i = 0; i < rx_ring->count; i++) {
1523 kfree(rx_ring->buffer_info[i].ps_pages);
1526 vfree(rx_ring->buffer_info);
1527 rx_ring->buffer_info = NULL;
1529 dma_free_coherent(&pdev->dev, rx_ring->size, rx_ring->desc,
1531 rx_ring->desc = NULL;
1535 * e1000_update_itr - update the dynamic ITR value based on statistics
1536 * @adapter: pointer to adapter
1537 * @itr_setting: current adapter->itr
1538 * @packets: the number of packets during this measurement interval
1539 * @bytes: the number of bytes during this measurement interval
1541 * Stores a new ITR value based on packets and byte
1542 * counts during the last interrupt. The advantage of per interrupt
1543 * computation is faster updates and more accurate ITR for the current
1544 * traffic pattern. Constants in this function were computed
1545 * based on theoretical maximum wire speed and thresholds were set based
1546 * on testing data as well as attempting to minimize response time
1547 * while increasing bulk throughput.
1548 * this functionality is controlled by the InterruptThrottleRate module
1549 * parameter (see e1000_param.c)
1551 static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
1552 u16 itr_setting, int packets,
1555 unsigned int retval = itr_setting;
1558 goto update_itr_done;
1560 switch (itr_setting) {
1561 case lowest_latency:
1562 /* handle TSO and jumbo frames */
1563 if (bytes/packets > 8000)
1564 retval = bulk_latency;
1565 else if ((packets < 5) && (bytes > 512)) {
1566 retval = low_latency;
1569 case low_latency: /* 50 usec aka 20000 ints/s */
1570 if (bytes > 10000) {
1571 /* this if handles the TSO accounting */
1572 if (bytes/packets > 8000) {
1573 retval = bulk_latency;
1574 } else if ((packets < 10) || ((bytes/packets) > 1200)) {
1575 retval = bulk_latency;
1576 } else if ((packets > 35)) {
1577 retval = lowest_latency;
1579 } else if (bytes/packets > 2000) {
1580 retval = bulk_latency;
1581 } else if (packets <= 2 && bytes < 512) {
1582 retval = lowest_latency;
1585 case bulk_latency: /* 250 usec aka 4000 ints/s */
1586 if (bytes > 25000) {
1588 retval = low_latency;
1590 } else if (bytes < 6000) {
1591 retval = low_latency;
1600 static void e1000_set_itr(struct e1000_adapter *adapter)
1602 struct e1000_hw *hw = &adapter->hw;
1604 u32 new_itr = adapter->itr;
1606 /* for non-gigabit speeds, just fix the interrupt rate at 4000 */
1607 if (adapter->link_speed != SPEED_1000) {
1613 adapter->tx_itr = e1000_update_itr(adapter,
1615 adapter->total_tx_packets,
1616 adapter->total_tx_bytes);
1617 /* conservative mode (itr 3) eliminates the lowest_latency setting */
1618 if (adapter->itr_setting == 3 && adapter->tx_itr == lowest_latency)
1619 adapter->tx_itr = low_latency;
1621 adapter->rx_itr = e1000_update_itr(adapter,
1623 adapter->total_rx_packets,
1624 adapter->total_rx_bytes);
1625 /* conservative mode (itr 3) eliminates the lowest_latency setting */
1626 if (adapter->itr_setting == 3 && adapter->rx_itr == lowest_latency)
1627 adapter->rx_itr = low_latency;
1629 current_itr = max(adapter->rx_itr, adapter->tx_itr);
1631 switch (current_itr) {
1632 /* counts and packets in update_itr are dependent on these numbers */
1633 case lowest_latency:
1637 new_itr = 20000; /* aka hwitr = ~200 */
1647 if (new_itr != adapter->itr) {
1649 * this attempts to bias the interrupt rate towards Bulk
1650 * by adding intermediate steps when interrupt rate is
1653 new_itr = new_itr > adapter->itr ?
1654 min(adapter->itr + (new_itr >> 2), new_itr) :
1656 adapter->itr = new_itr;
1657 ew32(ITR, 1000000000 / (new_itr * 256));
1662 * e1000_clean - NAPI Rx polling callback
1663 * @napi: struct associated with this polling callback
1664 * @budget: amount of packets driver is allowed to process this poll
1666 static int e1000_clean(struct napi_struct *napi, int budget)
1668 struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
1669 struct net_device *poll_dev = adapter->netdev;
1670 int tx_cleaned = 0, work_done = 0;
1672 /* Must NOT use netdev_priv macro here. */
1673 adapter = poll_dev->priv;
1676 * e1000_clean is called per-cpu. This lock protects
1677 * tx_ring from being cleaned by multiple cpus
1678 * simultaneously. A failure obtaining the lock means
1679 * tx_ring is currently being cleaned anyway.
1681 if (spin_trylock(&adapter->tx_queue_lock)) {
1682 tx_cleaned = e1000_clean_tx_irq(adapter);
1683 spin_unlock(&adapter->tx_queue_lock);
1686 adapter->clean_rx(adapter, &work_done, budget);
1691 /* If budget not fully consumed, exit the polling mode */
1692 if (work_done < budget) {
1693 if (adapter->itr_setting & 3)
1694 e1000_set_itr(adapter);
1695 netif_rx_complete(poll_dev, napi);
1696 e1000_irq_enable(adapter);
1702 static void e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid)
1704 struct e1000_adapter *adapter = netdev_priv(netdev);
1705 struct e1000_hw *hw = &adapter->hw;
1708 /* don't update vlan cookie if already programmed */
1709 if ((adapter->hw.mng_cookie.status &
1710 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
1711 (vid == adapter->mng_vlan_id))
1713 /* add VID to filter table */
1714 index = (vid >> 5) & 0x7F;
1715 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
1716 vfta |= (1 << (vid & 0x1F));
1717 e1000e_write_vfta(hw, index, vfta);
1720 static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid)
1722 struct e1000_adapter *adapter = netdev_priv(netdev);
1723 struct e1000_hw *hw = &adapter->hw;
1726 if (!test_bit(__E1000_DOWN, &adapter->state))
1727 e1000_irq_disable(adapter);
1728 vlan_group_set_device(adapter->vlgrp, vid, NULL);
1730 if (!test_bit(__E1000_DOWN, &adapter->state))
1731 e1000_irq_enable(adapter);
1733 if ((adapter->hw.mng_cookie.status &
1734 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
1735 (vid == adapter->mng_vlan_id)) {
1736 /* release control to f/w */
1737 e1000_release_hw_control(adapter);
1741 /* remove VID from filter table */
1742 index = (vid >> 5) & 0x7F;
1743 vfta = E1000_READ_REG_ARRAY(hw, E1000_VFTA, index);
1744 vfta &= ~(1 << (vid & 0x1F));
1745 e1000e_write_vfta(hw, index, vfta);
1748 static void e1000_update_mng_vlan(struct e1000_adapter *adapter)
1750 struct net_device *netdev = adapter->netdev;
1751 u16 vid = adapter->hw.mng_cookie.vlan_id;
1752 u16 old_vid = adapter->mng_vlan_id;
1754 if (!adapter->vlgrp)
1757 if (!vlan_group_get_device(adapter->vlgrp, vid)) {
1758 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
1759 if (adapter->hw.mng_cookie.status &
1760 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) {
1761 e1000_vlan_rx_add_vid(netdev, vid);
1762 adapter->mng_vlan_id = vid;
1765 if ((old_vid != (u16)E1000_MNG_VLAN_NONE) &&
1767 !vlan_group_get_device(adapter->vlgrp, old_vid))
1768 e1000_vlan_rx_kill_vid(netdev, old_vid);
1770 adapter->mng_vlan_id = vid;
1775 static void e1000_vlan_rx_register(struct net_device *netdev,
1776 struct vlan_group *grp)
1778 struct e1000_adapter *adapter = netdev_priv(netdev);
1779 struct e1000_hw *hw = &adapter->hw;
1782 if (!test_bit(__E1000_DOWN, &adapter->state))
1783 e1000_irq_disable(adapter);
1784 adapter->vlgrp = grp;
1787 /* enable VLAN tag insert/strip */
1789 ctrl |= E1000_CTRL_VME;
1792 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
1793 /* enable VLAN receive filtering */
1795 if (!(netdev->flags & IFF_PROMISC))
1796 rctl |= E1000_RCTL_VFE;
1797 rctl &= ~E1000_RCTL_CFIEN;
1799 e1000_update_mng_vlan(adapter);
1802 /* disable VLAN tag insert/strip */
1804 ctrl &= ~E1000_CTRL_VME;
1807 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER) {
1808 /* disable VLAN filtering */
1810 rctl &= ~E1000_RCTL_VFE;
1812 if (adapter->mng_vlan_id !=
1813 (u16)E1000_MNG_VLAN_NONE) {
1814 e1000_vlan_rx_kill_vid(netdev,
1815 adapter->mng_vlan_id);
1816 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
1821 if (!test_bit(__E1000_DOWN, &adapter->state))
1822 e1000_irq_enable(adapter);
1825 static void e1000_restore_vlan(struct e1000_adapter *adapter)
1829 e1000_vlan_rx_register(adapter->netdev, adapter->vlgrp);
1831 if (!adapter->vlgrp)
1834 for (vid = 0; vid < VLAN_GROUP_ARRAY_LEN; vid++) {
1835 if (!vlan_group_get_device(adapter->vlgrp, vid))
1837 e1000_vlan_rx_add_vid(adapter->netdev, vid);
1841 static void e1000_init_manageability(struct e1000_adapter *adapter)
1843 struct e1000_hw *hw = &adapter->hw;
1846 if (!(adapter->flags & FLAG_MNG_PT_ENABLED))
1852 * enable receiving management packets to the host. this will probably
1853 * generate destination unreachable messages from the host OS, but
1854 * the packets will be handled on SMBUS
1856 manc |= E1000_MANC_EN_MNG2HOST;
1857 manc2h = er32(MANC2H);
1858 #define E1000_MNG2HOST_PORT_623 (1 << 5)
1859 #define E1000_MNG2HOST_PORT_664 (1 << 6)
1860 manc2h |= E1000_MNG2HOST_PORT_623;
1861 manc2h |= E1000_MNG2HOST_PORT_664;
1862 ew32(MANC2H, manc2h);
1867 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset
1868 * @adapter: board private structure
1870 * Configure the Tx unit of the MAC after a reset.
1872 static void e1000_configure_tx(struct e1000_adapter *adapter)
1874 struct e1000_hw *hw = &adapter->hw;
1875 struct e1000_ring *tx_ring = adapter->tx_ring;
1877 u32 tdlen, tctl, tipg, tarc;
1880 /* Setup the HW Tx Head and Tail descriptor pointers */
1881 tdba = tx_ring->dma;
1882 tdlen = tx_ring->count * sizeof(struct e1000_tx_desc);
1883 ew32(TDBAL, (tdba & DMA_32BIT_MASK));
1884 ew32(TDBAH, (tdba >> 32));
1888 tx_ring->head = E1000_TDH;
1889 tx_ring->tail = E1000_TDT;
1891 /* Set the default values for the Tx Inter Packet Gap timer */
1892 tipg = DEFAULT_82543_TIPG_IPGT_COPPER; /* 8 */
1893 ipgr1 = DEFAULT_82543_TIPG_IPGR1; /* 8 */
1894 ipgr2 = DEFAULT_82543_TIPG_IPGR2; /* 6 */
1896 if (adapter->flags & FLAG_TIPG_MEDIUM_FOR_80003ESLAN)
1897 ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; /* 7 */
1899 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT;
1900 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT;
1903 /* Set the Tx Interrupt Delay register */
1904 ew32(TIDV, adapter->tx_int_delay);
1905 /* Tx irq moderation */
1906 ew32(TADV, adapter->tx_abs_int_delay);
1908 /* Program the Transmit Control Register */
1910 tctl &= ~E1000_TCTL_CT;
1911 tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC |
1912 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
1914 if (adapter->flags & FLAG_TARC_SPEED_MODE_BIT) {
1915 tarc = er32(TARC(0));
1917 * set the speed mode bit, we'll clear it if we're not at
1918 * gigabit link later
1920 #define SPEED_MODE_BIT (1 << 21)
1921 tarc |= SPEED_MODE_BIT;
1922 ew32(TARC(0), tarc);
1925 /* errata: program both queues to unweighted RR */
1926 if (adapter->flags & FLAG_TARC_SET_BIT_ZERO) {
1927 tarc = er32(TARC(0));
1929 ew32(TARC(0), tarc);
1930 tarc = er32(TARC(1));
1932 ew32(TARC(1), tarc);
1935 e1000e_config_collision_dist(hw);
1937 /* Setup Transmit Descriptor Settings for eop descriptor */
1938 adapter->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS;
1940 /* only set IDE if we are delaying interrupts using the timers */
1941 if (adapter->tx_int_delay)
1942 adapter->txd_cmd |= E1000_TXD_CMD_IDE;
1944 /* enable Report Status bit */
1945 adapter->txd_cmd |= E1000_TXD_CMD_RS;
1949 adapter->tx_queue_len = adapter->netdev->tx_queue_len;
1953 * e1000_setup_rctl - configure the receive control registers
1954 * @adapter: Board private structure
1956 #define PAGE_USE_COUNT(S) (((S) >> PAGE_SHIFT) + \
1957 (((S) & (PAGE_SIZE - 1)) ? 1 : 0))
1958 static void e1000_setup_rctl(struct e1000_adapter *adapter)
1960 struct e1000_hw *hw = &adapter->hw;
1965 /* Program MC offset vector base */
1967 rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
1968 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
1969 E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
1970 (adapter->hw.mac.mc_filter_type << E1000_RCTL_MO_SHIFT);
1972 /* Do not Store bad packets */
1973 rctl &= ~E1000_RCTL_SBP;
1975 /* Enable Long Packet receive */
1976 if (adapter->netdev->mtu <= ETH_DATA_LEN)
1977 rctl &= ~E1000_RCTL_LPE;
1979 rctl |= E1000_RCTL_LPE;
1981 /* Enable hardware CRC frame stripping */
1982 rctl |= E1000_RCTL_SECRC;
1984 /* Setup buffer sizes */
1985 rctl &= ~E1000_RCTL_SZ_4096;
1986 rctl |= E1000_RCTL_BSEX;
1987 switch (adapter->rx_buffer_len) {
1989 rctl |= E1000_RCTL_SZ_256;
1990 rctl &= ~E1000_RCTL_BSEX;
1993 rctl |= E1000_RCTL_SZ_512;
1994 rctl &= ~E1000_RCTL_BSEX;
1997 rctl |= E1000_RCTL_SZ_1024;
1998 rctl &= ~E1000_RCTL_BSEX;
2002 rctl |= E1000_RCTL_SZ_2048;
2003 rctl &= ~E1000_RCTL_BSEX;
2006 rctl |= E1000_RCTL_SZ_4096;
2009 rctl |= E1000_RCTL_SZ_8192;
2012 rctl |= E1000_RCTL_SZ_16384;
2017 * 82571 and greater support packet-split where the protocol
2018 * header is placed in skb->data and the packet data is
2019 * placed in pages hanging off of skb_shinfo(skb)->nr_frags.
2020 * In the case of a non-split, skb->data is linearly filled,
2021 * followed by the page buffers. Therefore, skb->data is
2022 * sized to hold the largest protocol header.
2024 * allocations using alloc_page take too long for regular MTU
2025 * so only enable packet split for jumbo frames
2027 * Using pages when the page size is greater than 16k wastes
2028 * a lot of memory, since we allocate 3 pages at all times
2031 pages = PAGE_USE_COUNT(adapter->netdev->mtu);
2032 if (!(adapter->flags & FLAG_IS_ICH) && (pages <= 3) &&
2033 (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE))
2034 adapter->rx_ps_pages = pages;
2036 adapter->rx_ps_pages = 0;
2038 if (adapter->rx_ps_pages) {
2039 /* Configure extra packet-split registers */
2040 rfctl = er32(RFCTL);
2041 rfctl |= E1000_RFCTL_EXTEN;
2043 * disable packet split support for IPv6 extension headers,
2044 * because some malformed IPv6 headers can hang the Rx
2046 rfctl |= (E1000_RFCTL_IPV6_EX_DIS |
2047 E1000_RFCTL_NEW_IPV6_EXT_DIS);
2051 /* Enable Packet split descriptors */
2052 rctl |= E1000_RCTL_DTYP_PS;
2054 psrctl |= adapter->rx_ps_bsize0 >>
2055 E1000_PSRCTL_BSIZE0_SHIFT;
2057 switch (adapter->rx_ps_pages) {
2059 psrctl |= PAGE_SIZE <<
2060 E1000_PSRCTL_BSIZE3_SHIFT;
2062 psrctl |= PAGE_SIZE <<
2063 E1000_PSRCTL_BSIZE2_SHIFT;
2065 psrctl |= PAGE_SIZE >>
2066 E1000_PSRCTL_BSIZE1_SHIFT;
2070 ew32(PSRCTL, psrctl);
2074 /* just started the receive unit, no need to restart */
2075 adapter->flags &= ~FLAG_RX_RESTART_NOW;
2079 * e1000_configure_rx - Configure Receive Unit after Reset
2080 * @adapter: board private structure
2082 * Configure the Rx unit of the MAC after a reset.
2084 static void e1000_configure_rx(struct e1000_adapter *adapter)
2086 struct e1000_hw *hw = &adapter->hw;
2087 struct e1000_ring *rx_ring = adapter->rx_ring;
2089 u32 rdlen, rctl, rxcsum, ctrl_ext;
2091 if (adapter->rx_ps_pages) {
2092 /* this is a 32 byte descriptor */
2093 rdlen = rx_ring->count *
2094 sizeof(union e1000_rx_desc_packet_split);
2095 adapter->clean_rx = e1000_clean_rx_irq_ps;
2096 adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps;
2097 } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) {
2098 rdlen = rx_ring->count * sizeof(struct e1000_rx_desc);
2099 adapter->clean_rx = e1000_clean_jumbo_rx_irq;
2100 adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers;
2102 rdlen = rx_ring->count * sizeof(struct e1000_rx_desc);
2103 adapter->clean_rx = e1000_clean_rx_irq;
2104 adapter->alloc_rx_buf = e1000_alloc_rx_buffers;
2107 /* disable receives while setting up the descriptors */
2109 ew32(RCTL, rctl & ~E1000_RCTL_EN);
2113 /* set the Receive Delay Timer Register */
2114 ew32(RDTR, adapter->rx_int_delay);
2116 /* irq moderation */
2117 ew32(RADV, adapter->rx_abs_int_delay);
2118 if (adapter->itr_setting != 0)
2119 ew32(ITR, 1000000000 / (adapter->itr * 256));
2121 ctrl_ext = er32(CTRL_EXT);
2122 /* Reset delay timers after every interrupt */
2123 ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR;
2124 /* Auto-Mask interrupts upon ICR access */
2125 ctrl_ext |= E1000_CTRL_EXT_IAME;
2126 ew32(IAM, 0xffffffff);
2127 ew32(CTRL_EXT, ctrl_ext);
2131 * Setup the HW Rx Head and Tail Descriptor Pointers and
2132 * the Base and Length of the Rx Descriptor Ring
2134 rdba = rx_ring->dma;
2135 ew32(RDBAL, (rdba & DMA_32BIT_MASK));
2136 ew32(RDBAH, (rdba >> 32));
2140 rx_ring->head = E1000_RDH;
2141 rx_ring->tail = E1000_RDT;
2143 /* Enable Receive Checksum Offload for TCP and UDP */
2144 rxcsum = er32(RXCSUM);
2145 if (adapter->flags & FLAG_RX_CSUM_ENABLED) {
2146 rxcsum |= E1000_RXCSUM_TUOFL;
2149 * IPv4 payload checksum for UDP fragments must be
2150 * used in conjunction with packet-split.
2152 if (adapter->rx_ps_pages)
2153 rxcsum |= E1000_RXCSUM_IPPCSE;
2155 rxcsum &= ~E1000_RXCSUM_TUOFL;
2156 /* no need to clear IPPCSE as it defaults to 0 */
2158 ew32(RXCSUM, rxcsum);
2161 * Enable early receives on supported devices, only takes effect when
2162 * packet size is equal or larger than the specified value (in 8 byte
2163 * units), e.g. using jumbo frames when setting to E1000_ERT_2048
2165 if ((adapter->flags & FLAG_HAS_ERT) &&
2166 (adapter->netdev->mtu > ETH_DATA_LEN)) {
2167 u32 rxdctl = er32(RXDCTL(0));
2168 ew32(RXDCTL(0), rxdctl | 0x3);
2169 ew32(ERT, E1000_ERT_2048 | (1 << 13));
2171 * With jumbo frames and early-receive enabled, excessive
2172 * C4->C2 latencies result in dropped transactions.
2174 pm_qos_update_requirement(PM_QOS_CPU_DMA_LATENCY,
2175 e1000e_driver_name, 55);
2177 pm_qos_update_requirement(PM_QOS_CPU_DMA_LATENCY,
2179 PM_QOS_DEFAULT_VALUE);
2182 /* Enable Receives */
2187 * e1000_update_mc_addr_list - Update Multicast addresses
2188 * @hw: pointer to the HW structure
2189 * @mc_addr_list: array of multicast addresses to program
2190 * @mc_addr_count: number of multicast addresses to program
2191 * @rar_used_count: the first RAR register free to program
2192 * @rar_count: total number of supported Receive Address Registers
2194 * Updates the Receive Address Registers and Multicast Table Array.
2195 * The caller must have a packed mc_addr_list of multicast addresses.
2196 * The parameter rar_count will usually be hw->mac.rar_entry_count
2197 * unless there are workarounds that change this. Currently no func pointer
2198 * exists and all implementations are handled in the generic version of this
2201 static void e1000_update_mc_addr_list(struct e1000_hw *hw, u8 *mc_addr_list,
2202 u32 mc_addr_count, u32 rar_used_count,
2205 hw->mac.ops.update_mc_addr_list(hw, mc_addr_list, mc_addr_count,
2206 rar_used_count, rar_count);
2210 * e1000_set_multi - Multicast and Promiscuous mode set
2211 * @netdev: network interface device structure
2213 * The set_multi entry point is called whenever the multicast address
2214 * list or the network interface flags are updated. This routine is
2215 * responsible for configuring the hardware for proper multicast,
2216 * promiscuous mode, and all-multi behavior.
2218 static void e1000_set_multi(struct net_device *netdev)
2220 struct e1000_adapter *adapter = netdev_priv(netdev);
2221 struct e1000_hw *hw = &adapter->hw;
2222 struct e1000_mac_info *mac = &hw->mac;
2223 struct dev_mc_list *mc_ptr;
2228 /* Check for Promiscuous and All Multicast modes */
2232 if (netdev->flags & IFF_PROMISC) {
2233 rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE);
2234 rctl &= ~E1000_RCTL_VFE;
2236 if (netdev->flags & IFF_ALLMULTI) {
2237 rctl |= E1000_RCTL_MPE;
2238 rctl &= ~E1000_RCTL_UPE;
2240 rctl &= ~(E1000_RCTL_UPE | E1000_RCTL_MPE);
2242 if (adapter->vlgrp && adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
2243 rctl |= E1000_RCTL_VFE;
2248 if (netdev->mc_count) {
2249 mta_list = kmalloc(netdev->mc_count * 6, GFP_ATOMIC);
2253 /* prepare a packed array of only addresses. */
2254 mc_ptr = netdev->mc_list;
2256 for (i = 0; i < netdev->mc_count; i++) {
2259 memcpy(mta_list + (i*ETH_ALEN), mc_ptr->dmi_addr,
2261 mc_ptr = mc_ptr->next;
2264 e1000_update_mc_addr_list(hw, mta_list, i, 1,
2265 mac->rar_entry_count);
2269 * if we're called from probe, we might not have
2270 * anything to do here, so clear out the list
2272 e1000_update_mc_addr_list(hw, NULL, 0, 1, mac->rar_entry_count);
2277 * e1000_configure - configure the hardware for Rx and Tx
2278 * @adapter: private board structure
2280 static void e1000_configure(struct e1000_adapter *adapter)
2282 e1000_set_multi(adapter->netdev);
2284 e1000_restore_vlan(adapter);
2285 e1000_init_manageability(adapter);
2287 e1000_configure_tx(adapter);
2288 e1000_setup_rctl(adapter);
2289 e1000_configure_rx(adapter);
2290 adapter->alloc_rx_buf(adapter, e1000_desc_unused(adapter->rx_ring));
2294 * e1000e_power_up_phy - restore link in case the phy was powered down
2295 * @adapter: address of board private structure
2297 * The phy may be powered down to save power and turn off link when the
2298 * driver is unloaded and wake on lan is not enabled (among others)
2299 * *** this routine MUST be followed by a call to e1000e_reset ***
2301 void e1000e_power_up_phy(struct e1000_adapter *adapter)
2305 /* Just clear the power down bit to wake the phy back up */
2306 if (adapter->hw.phy.media_type == e1000_media_type_copper) {
2308 * According to the manual, the phy will retain its
2309 * settings across a power-down/up cycle
2311 e1e_rphy(&adapter->hw, PHY_CONTROL, &mii_reg);
2312 mii_reg &= ~MII_CR_POWER_DOWN;
2313 e1e_wphy(&adapter->hw, PHY_CONTROL, mii_reg);
2316 adapter->hw.mac.ops.setup_link(&adapter->hw);
2320 * e1000_power_down_phy - Power down the PHY
2322 * Power down the PHY so no link is implied when interface is down
2323 * The PHY cannot be powered down is management or WoL is active
2325 static void e1000_power_down_phy(struct e1000_adapter *adapter)
2327 struct e1000_hw *hw = &adapter->hw;
2330 /* WoL is enabled */
2334 /* non-copper PHY? */
2335 if (adapter->hw.phy.media_type != e1000_media_type_copper)
2338 /* reset is blocked because of a SoL/IDER session */
2339 if (e1000e_check_mng_mode(hw) || e1000_check_reset_block(hw))
2342 /* manageability (AMT) is enabled */
2343 if (er32(MANC) & E1000_MANC_SMBUS_EN)
2346 /* power down the PHY */
2347 e1e_rphy(hw, PHY_CONTROL, &mii_reg);
2348 mii_reg |= MII_CR_POWER_DOWN;
2349 e1e_wphy(hw, PHY_CONTROL, mii_reg);
2354 * e1000e_reset - bring the hardware into a known good state
2356 * This function boots the hardware and enables some settings that
2357 * require a configuration cycle of the hardware - those cannot be
2358 * set/changed during runtime. After reset the device needs to be
2359 * properly configured for Rx, Tx etc.
2361 void e1000e_reset(struct e1000_adapter *adapter)
2363 struct e1000_mac_info *mac = &adapter->hw.mac;
2364 struct e1000_fc_info *fc = &adapter->hw.fc;
2365 struct e1000_hw *hw = &adapter->hw;
2366 u32 tx_space, min_tx_space, min_rx_space;
2367 u32 pba = adapter->pba;
2370 /* reset Packet Buffer Allocation to default */
2373 if (adapter->max_frame_size > ETH_FRAME_LEN + ETH_FCS_LEN) {
2375 * To maintain wire speed transmits, the Tx FIFO should be
2376 * large enough to accommodate two full transmit packets,
2377 * rounded up to the next 1KB and expressed in KB. Likewise,
2378 * the Rx FIFO should be large enough to accommodate at least
2379 * one full receive packet and is similarly rounded up and
2383 /* upper 16 bits has Tx packet buffer allocation size in KB */
2384 tx_space = pba >> 16;
2385 /* lower 16 bits has Rx packet buffer allocation size in KB */
2388 * the Tx fifo also stores 16 bytes of information about the tx
2389 * but don't include ethernet FCS because hardware appends it
2391 min_tx_space = (adapter->max_frame_size +
2392 sizeof(struct e1000_tx_desc) -
2394 min_tx_space = ALIGN(min_tx_space, 1024);
2395 min_tx_space >>= 10;
2396 /* software strips receive CRC, so leave room for it */
2397 min_rx_space = adapter->max_frame_size;
2398 min_rx_space = ALIGN(min_rx_space, 1024);
2399 min_rx_space >>= 10;
2402 * If current Tx allocation is less than the min Tx FIFO size,
2403 * and the min Tx FIFO size is less than the current Rx FIFO
2404 * allocation, take space away from current Rx allocation
2406 if ((tx_space < min_tx_space) &&
2407 ((min_tx_space - tx_space) < pba)) {
2408 pba -= min_tx_space - tx_space;
2411 * if short on Rx space, Rx wins and must trump tx
2412 * adjustment or use Early Receive if available
2414 if ((pba < min_rx_space) &&
2415 (!(adapter->flags & FLAG_HAS_ERT)))
2416 /* ERT enabled in e1000_configure_rx */
2425 * flow control settings
2427 * The high water mark must be low enough to fit one full frame
2428 * (or the size used for early receive) above it in the Rx FIFO.
2429 * Set it to the lower of:
2430 * - 90% of the Rx FIFO size, and
2431 * - the full Rx FIFO size minus the early receive size (for parts
2432 * with ERT support assuming ERT set to E1000_ERT_2048), or
2433 * - the full Rx FIFO size minus one full frame
2435 if (adapter->flags & FLAG_HAS_ERT)
2436 hwm = min(((pba << 10) * 9 / 10),
2437 ((pba << 10) - (E1000_ERT_2048 << 3)));
2439 hwm = min(((pba << 10) * 9 / 10),
2440 ((pba << 10) - adapter->max_frame_size));
2442 fc->high_water = hwm & 0xFFF8; /* 8-byte granularity */
2443 fc->low_water = fc->high_water - 8;
2445 if (adapter->flags & FLAG_DISABLE_FC_PAUSE_TIME)
2446 fc->pause_time = 0xFFFF;
2448 fc->pause_time = E1000_FC_PAUSE_TIME;
2450 fc->type = fc->original_type;
2452 /* Allow time for pending master requests to run */
2453 mac->ops.reset_hw(hw);
2456 * For parts with AMT enabled, let the firmware know
2457 * that the network interface is in control
2459 if ((adapter->flags & FLAG_HAS_AMT) && e1000e_check_mng_mode(hw))
2460 e1000_get_hw_control(adapter);
2464 if (mac->ops.init_hw(hw))
2465 ndev_err(adapter->netdev, "Hardware Error\n");
2467 e1000_update_mng_vlan(adapter);
2469 /* Enable h/w to recognize an 802.1Q VLAN Ethernet packet */
2470 ew32(VET, ETH_P_8021Q);
2472 e1000e_reset_adaptive(hw);
2473 e1000_get_phy_info(hw);
2475 if (!(adapter->flags & FLAG_SMART_POWER_DOWN)) {
2478 * speed up time to link by disabling smart power down, ignore
2479 * the return value of this function because there is nothing
2480 * different we would do if it failed
2482 e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data);
2483 phy_data &= ~IGP02E1000_PM_SPD;
2484 e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
2488 int e1000e_up(struct e1000_adapter *adapter)
2490 struct e1000_hw *hw = &adapter->hw;
2492 /* hardware has been reset, we need to reload some things */
2493 e1000_configure(adapter);
2495 clear_bit(__E1000_DOWN, &adapter->state);
2497 napi_enable(&adapter->napi);
2498 e1000_irq_enable(adapter);
2500 /* fire a link change interrupt to start the watchdog */
2501 ew32(ICS, E1000_ICS_LSC);
2505 void e1000e_down(struct e1000_adapter *adapter)
2507 struct net_device *netdev = adapter->netdev;
2508 struct e1000_hw *hw = &adapter->hw;
2512 * signal that we're down so the interrupt handler does not
2513 * reschedule our watchdog timer
2515 set_bit(__E1000_DOWN, &adapter->state);
2517 /* disable receives in the hardware */
2519 ew32(RCTL, rctl & ~E1000_RCTL_EN);
2520 /* flush and sleep below */
2522 netif_stop_queue(netdev);
2524 /* disable transmits in the hardware */
2526 tctl &= ~E1000_TCTL_EN;
2528 /* flush both disables and wait for them to finish */
2532 napi_disable(&adapter->napi);
2533 e1000_irq_disable(adapter);
2535 del_timer_sync(&adapter->watchdog_timer);
2536 del_timer_sync(&adapter->phy_info_timer);
2538 netdev->tx_queue_len = adapter->tx_queue_len;
2539 netif_carrier_off(netdev);
2540 adapter->link_speed = 0;
2541 adapter->link_duplex = 0;
2543 if (!pci_channel_offline(adapter->pdev))
2544 e1000e_reset(adapter);
2545 e1000_clean_tx_ring(adapter);
2546 e1000_clean_rx_ring(adapter);
2549 * TODO: for power management, we could drop the link and
2550 * pci_disable_device here.
2554 void e1000e_reinit_locked(struct e1000_adapter *adapter)
2557 while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
2559 e1000e_down(adapter);
2561 clear_bit(__E1000_RESETTING, &adapter->state);
2565 * e1000_sw_init - Initialize general software structures (struct e1000_adapter)
2566 * @adapter: board private structure to initialize
2568 * e1000_sw_init initializes the Adapter private data structure.
2569 * Fields are initialized based on PCI device information and
2570 * OS network device settings (MTU size).
2572 static int __devinit e1000_sw_init(struct e1000_adapter *adapter)
2574 struct net_device *netdev = adapter->netdev;
2576 adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN;
2577 adapter->rx_ps_bsize0 = 128;
2578 adapter->max_frame_size = netdev->mtu + ETH_HLEN + ETH_FCS_LEN;
2579 adapter->min_frame_size = ETH_ZLEN + ETH_FCS_LEN;
2581 adapter->tx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
2582 if (!adapter->tx_ring)
2585 adapter->rx_ring = kzalloc(sizeof(struct e1000_ring), GFP_KERNEL);
2586 if (!adapter->rx_ring)
2589 spin_lock_init(&adapter->tx_queue_lock);
2591 /* Explicitly disable IRQ since the NIC can be in any state. */
2592 e1000_irq_disable(adapter);
2594 spin_lock_init(&adapter->stats_lock);
2596 set_bit(__E1000_DOWN, &adapter->state);
2600 ndev_err(netdev, "Unable to allocate memory for queues\n");
2601 kfree(adapter->rx_ring);
2602 kfree(adapter->tx_ring);
2607 * e1000_open - Called when a network interface is made active
2608 * @netdev: network interface device structure
2610 * Returns 0 on success, negative value on failure
2612 * The open entry point is called when a network interface is made
2613 * active by the system (IFF_UP). At this point all resources needed
2614 * for transmit and receive operations are allocated, the interrupt
2615 * handler is registered with the OS, the watchdog timer is started,
2616 * and the stack is notified that the interface is ready.
2618 static int e1000_open(struct net_device *netdev)
2620 struct e1000_adapter *adapter = netdev_priv(netdev);
2621 struct e1000_hw *hw = &adapter->hw;
2624 /* disallow open during test */
2625 if (test_bit(__E1000_TESTING, &adapter->state))
2628 /* allocate transmit descriptors */
2629 err = e1000e_setup_tx_resources(adapter);
2633 /* allocate receive descriptors */
2634 err = e1000e_setup_rx_resources(adapter);
2638 e1000e_power_up_phy(adapter);
2640 adapter->mng_vlan_id = E1000_MNG_VLAN_NONE;
2641 if ((adapter->hw.mng_cookie.status &
2642 E1000_MNG_DHCP_COOKIE_STATUS_VLAN))
2643 e1000_update_mng_vlan(adapter);
2646 * If AMT is enabled, let the firmware know that the network
2647 * interface is now open
2649 if ((adapter->flags & FLAG_HAS_AMT) &&
2650 e1000e_check_mng_mode(&adapter->hw))
2651 e1000_get_hw_control(adapter);
2654 * before we allocate an interrupt, we must be ready to handle it.
2655 * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt
2656 * as soon as we call pci_request_irq, so we have to setup our
2657 * clean_rx handler before we do so.
2659 e1000_configure(adapter);
2661 err = e1000_request_irq(adapter);
2665 /* From here on the code is the same as e1000e_up() */
2666 clear_bit(__E1000_DOWN, &adapter->state);
2668 napi_enable(&adapter->napi);
2670 e1000_irq_enable(adapter);
2672 /* fire a link status change interrupt to start the watchdog */
2673 ew32(ICS, E1000_ICS_LSC);
2678 e1000_release_hw_control(adapter);
2679 e1000_power_down_phy(adapter);
2680 e1000e_free_rx_resources(adapter);
2682 e1000e_free_tx_resources(adapter);
2684 e1000e_reset(adapter);
2690 * e1000_close - Disables a network interface
2691 * @netdev: network interface device structure
2693 * Returns 0, this is not allowed to fail
2695 * The close entry point is called when an interface is de-activated
2696 * by the OS. The hardware is still under the drivers control, but
2697 * needs to be disabled. A global MAC reset is issued to stop the
2698 * hardware, and all transmit and receive resources are freed.
2700 static int e1000_close(struct net_device *netdev)
2702 struct e1000_adapter *adapter = netdev_priv(netdev);
2704 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
2705 e1000e_down(adapter);
2706 e1000_power_down_phy(adapter);
2707 e1000_free_irq(adapter);
2709 e1000e_free_tx_resources(adapter);
2710 e1000e_free_rx_resources(adapter);
2713 * kill manageability vlan ID if supported, but not if a vlan with
2714 * the same ID is registered on the host OS (let 8021q kill it)
2716 if ((adapter->hw.mng_cookie.status &
2717 E1000_MNG_DHCP_COOKIE_STATUS_VLAN) &&
2719 vlan_group_get_device(adapter->vlgrp, adapter->mng_vlan_id)))
2720 e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id);
2723 * If AMT is enabled, let the firmware know that the network
2724 * interface is now closed
2726 if ((adapter->flags & FLAG_HAS_AMT) &&
2727 e1000e_check_mng_mode(&adapter->hw))
2728 e1000_release_hw_control(adapter);
2733 * e1000_set_mac - Change the Ethernet Address of the NIC
2734 * @netdev: network interface device structure
2735 * @p: pointer to an address structure
2737 * Returns 0 on success, negative on failure
2739 static int e1000_set_mac(struct net_device *netdev, void *p)
2741 struct e1000_adapter *adapter = netdev_priv(netdev);
2742 struct sockaddr *addr = p;
2744 if (!is_valid_ether_addr(addr->sa_data))
2745 return -EADDRNOTAVAIL;
2747 memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
2748 memcpy(adapter->hw.mac.addr, addr->sa_data, netdev->addr_len);
2750 e1000e_rar_set(&adapter->hw, adapter->hw.mac.addr, 0);
2752 if (adapter->flags & FLAG_RESET_OVERWRITES_LAA) {
2753 /* activate the work around */
2754 e1000e_set_laa_state_82571(&adapter->hw, 1);
2757 * Hold a copy of the LAA in RAR[14] This is done so that
2758 * between the time RAR[0] gets clobbered and the time it
2759 * gets fixed (in e1000_watchdog), the actual LAA is in one
2760 * of the RARs and no incoming packets directed to this port
2761 * are dropped. Eventually the LAA will be in RAR[0] and
2764 e1000e_rar_set(&adapter->hw,
2765 adapter->hw.mac.addr,
2766 adapter->hw.mac.rar_entry_count - 1);
2773 * Need to wait a few seconds after link up to get diagnostic information from
2776 static void e1000_update_phy_info(unsigned long data)
2778 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
2779 e1000_get_phy_info(&adapter->hw);
2783 * e1000e_update_stats - Update the board statistics counters
2784 * @adapter: board private structure
2786 void e1000e_update_stats(struct e1000_adapter *adapter)
2788 struct e1000_hw *hw = &adapter->hw;
2789 struct pci_dev *pdev = adapter->pdev;
2790 unsigned long irq_flags;
2793 #define PHY_IDLE_ERROR_COUNT_MASK 0x00FF
2796 * Prevent stats update while adapter is being reset, or if the pci
2797 * connection is down.
2799 if (adapter->link_speed == 0)
2801 if (pci_channel_offline(pdev))
2804 spin_lock_irqsave(&adapter->stats_lock, irq_flags);
2807 * these counters are modified from e1000_adjust_tbi_stats,
2808 * called from the interrupt context, so they must only
2809 * be written while holding adapter->stats_lock
2812 adapter->stats.crcerrs += er32(CRCERRS);
2813 adapter->stats.gprc += er32(GPRC);
2814 adapter->stats.gorc += er32(GORCL);
2815 er32(GORCH); /* Clear gorc */
2816 adapter->stats.bprc += er32(BPRC);
2817 adapter->stats.mprc += er32(MPRC);
2818 adapter->stats.roc += er32(ROC);
2820 adapter->stats.mpc += er32(MPC);
2821 adapter->stats.scc += er32(SCC);
2822 adapter->stats.ecol += er32(ECOL);
2823 adapter->stats.mcc += er32(MCC);
2824 adapter->stats.latecol += er32(LATECOL);
2825 adapter->stats.dc += er32(DC);
2826 adapter->stats.xonrxc += er32(XONRXC);
2827 adapter->stats.xontxc += er32(XONTXC);
2828 adapter->stats.xoffrxc += er32(XOFFRXC);
2829 adapter->stats.xofftxc += er32(XOFFTXC);
2830 adapter->stats.gptc += er32(GPTC);
2831 adapter->stats.gotc += er32(GOTCL);
2832 er32(GOTCH); /* Clear gotc */
2833 adapter->stats.rnbc += er32(RNBC);
2834 adapter->stats.ruc += er32(RUC);
2836 adapter->stats.mptc += er32(MPTC);
2837 adapter->stats.bptc += er32(BPTC);
2839 /* used for adaptive IFS */
2841 hw->mac.tx_packet_delta = er32(TPT);
2842 adapter->stats.tpt += hw->mac.tx_packet_delta;
2843 hw->mac.collision_delta = er32(COLC);
2844 adapter->stats.colc += hw->mac.collision_delta;
2846 adapter->stats.algnerrc += er32(ALGNERRC);
2847 adapter->stats.rxerrc += er32(RXERRC);
2848 adapter->stats.tncrs += er32(TNCRS);
2849 adapter->stats.cexterr += er32(CEXTERR);
2850 adapter->stats.tsctc += er32(TSCTC);
2851 adapter->stats.tsctfc += er32(TSCTFC);
2853 /* Fill out the OS statistics structure */
2854 adapter->net_stats.multicast = adapter->stats.mprc;
2855 adapter->net_stats.collisions = adapter->stats.colc;
2860 * RLEC on some newer hardware can be incorrect so build
2861 * our own version based on RUC and ROC
2863 adapter->net_stats.rx_errors = adapter->stats.rxerrc +
2864 adapter->stats.crcerrs + adapter->stats.algnerrc +
2865 adapter->stats.ruc + adapter->stats.roc +
2866 adapter->stats.cexterr;
2867 adapter->net_stats.rx_length_errors = adapter->stats.ruc +
2869 adapter->net_stats.rx_crc_errors = adapter->stats.crcerrs;
2870 adapter->net_stats.rx_frame_errors = adapter->stats.algnerrc;
2871 adapter->net_stats.rx_missed_errors = adapter->stats.mpc;
2874 adapter->net_stats.tx_errors = adapter->stats.ecol +
2875 adapter->stats.latecol;
2876 adapter->net_stats.tx_aborted_errors = adapter->stats.ecol;
2877 adapter->net_stats.tx_window_errors = adapter->stats.latecol;
2878 adapter->net_stats.tx_carrier_errors = adapter->stats.tncrs;
2880 /* Tx Dropped needs to be maintained elsewhere */
2883 if (hw->phy.media_type == e1000_media_type_copper) {
2884 if ((adapter->link_speed == SPEED_1000) &&
2885 (!e1e_rphy(hw, PHY_1000T_STATUS, &phy_tmp))) {
2886 phy_tmp &= PHY_IDLE_ERROR_COUNT_MASK;
2887 adapter->phy_stats.idle_errors += phy_tmp;
2891 /* Management Stats */
2892 adapter->stats.mgptc += er32(MGTPTC);
2893 adapter->stats.mgprc += er32(MGTPRC);
2894 adapter->stats.mgpdc += er32(MGTPDC);
2896 spin_unlock_irqrestore(&adapter->stats_lock, irq_flags);
2900 * e1000_phy_read_status - Update the PHY register status snapshot
2901 * @adapter: board private structure
2903 static void e1000_phy_read_status(struct e1000_adapter *adapter)
2905 struct e1000_hw *hw = &adapter->hw;
2906 struct e1000_phy_regs *phy = &adapter->phy_regs;
2908 unsigned long irq_flags;
2911 spin_lock_irqsave(&adapter->stats_lock, irq_flags);
2913 if ((er32(STATUS) & E1000_STATUS_LU) &&
2914 (adapter->hw.phy.media_type == e1000_media_type_copper)) {
2915 ret_val = e1e_rphy(hw, PHY_CONTROL, &phy->bmcr);
2916 ret_val |= e1e_rphy(hw, PHY_STATUS, &phy->bmsr);
2917 ret_val |= e1e_rphy(hw, PHY_AUTONEG_ADV, &phy->advertise);
2918 ret_val |= e1e_rphy(hw, PHY_LP_ABILITY, &phy->lpa);
2919 ret_val |= e1e_rphy(hw, PHY_AUTONEG_EXP, &phy->expansion);
2920 ret_val |= e1e_rphy(hw, PHY_1000T_CTRL, &phy->ctrl1000);
2921 ret_val |= e1e_rphy(hw, PHY_1000T_STATUS, &phy->stat1000);
2922 ret_val |= e1e_rphy(hw, PHY_EXT_STATUS, &phy->estatus);
2924 ndev_warn(adapter->netdev,
2925 "Error reading PHY register\n");
2928 * Do not read PHY registers if link is not up
2929 * Set values to typical power-on defaults
2931 phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX);
2932 phy->bmsr = (BMSR_100FULL | BMSR_100HALF | BMSR_10FULL |
2933 BMSR_10HALF | BMSR_ESTATEN | BMSR_ANEGCAPABLE |
2935 phy->advertise = (ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP |
2936 ADVERTISE_ALL | ADVERTISE_CSMA);
2938 phy->expansion = EXPANSION_ENABLENPAGE;
2939 phy->ctrl1000 = ADVERTISE_1000FULL;
2941 phy->estatus = (ESTATUS_1000_TFULL | ESTATUS_1000_THALF);
2944 spin_unlock_irqrestore(&adapter->stats_lock, irq_flags);
2947 static void e1000_print_link_info(struct e1000_adapter *adapter)
2949 struct e1000_hw *hw = &adapter->hw;
2950 struct net_device *netdev = adapter->netdev;
2951 u32 ctrl = er32(CTRL);
2954 "Link is Up %d Mbps %s, Flow Control: %s\n",
2955 adapter->link_speed,
2956 (adapter->link_duplex == FULL_DUPLEX) ?
2957 "Full Duplex" : "Half Duplex",
2958 ((ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE)) ?
2960 ((ctrl & E1000_CTRL_RFCE) ? "RX" :
2961 ((ctrl & E1000_CTRL_TFCE) ? "TX" : "None" )));
2964 static bool e1000_has_link(struct e1000_adapter *adapter)
2966 struct e1000_hw *hw = &adapter->hw;
2967 bool link_active = 0;
2971 * get_link_status is set on LSC (link status) interrupt or
2972 * Rx sequence error interrupt. get_link_status will stay
2973 * false until the check_for_link establishes link
2974 * for copper adapters ONLY
2976 switch (hw->phy.media_type) {
2977 case e1000_media_type_copper:
2978 if (hw->mac.get_link_status) {
2979 ret_val = hw->mac.ops.check_for_link(hw);
2980 link_active = !hw->mac.get_link_status;
2985 case e1000_media_type_fiber:
2986 ret_val = hw->mac.ops.check_for_link(hw);
2987 link_active = !!(er32(STATUS) & E1000_STATUS_LU);
2989 case e1000_media_type_internal_serdes:
2990 ret_val = hw->mac.ops.check_for_link(hw);
2991 link_active = adapter->hw.mac.serdes_has_link;
2994 case e1000_media_type_unknown:
2998 if ((ret_val == E1000_ERR_PHY) && (hw->phy.type == e1000_phy_igp_3) &&
2999 (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) {
3000 /* See e1000_kmrn_lock_loss_workaround_ich8lan() */
3001 ndev_info(adapter->netdev,
3002 "Gigabit has been disabled, downgrading speed\n");
3008 static void e1000e_enable_receives(struct e1000_adapter *adapter)
3010 /* make sure the receive unit is started */
3011 if ((adapter->flags & FLAG_RX_NEEDS_RESTART) &&
3012 (adapter->flags & FLAG_RX_RESTART_NOW)) {
3013 struct e1000_hw *hw = &adapter->hw;
3014 u32 rctl = er32(RCTL);
3015 ew32(RCTL, rctl | E1000_RCTL_EN);
3016 adapter->flags &= ~FLAG_RX_RESTART_NOW;
3021 * e1000_watchdog - Timer Call-back
3022 * @data: pointer to adapter cast into an unsigned long
3024 static void e1000_watchdog(unsigned long data)
3026 struct e1000_adapter *adapter = (struct e1000_adapter *) data;
3028 /* Do the rest outside of interrupt context */
3029 schedule_work(&adapter->watchdog_task);
3031 /* TODO: make this use queue_delayed_work() */
3034 static void e1000_watchdog_task(struct work_struct *work)
3036 struct e1000_adapter *adapter = container_of(work,
3037 struct e1000_adapter, watchdog_task);
3038 struct net_device *netdev = adapter->netdev;
3039 struct e1000_mac_info *mac = &adapter->hw.mac;
3040 struct e1000_ring *tx_ring = adapter->tx_ring;
3041 struct e1000_hw *hw = &adapter->hw;
3045 link = e1000_has_link(adapter);
3046 if ((netif_carrier_ok(netdev)) && link) {
3047 e1000e_enable_receives(adapter);
3051 if ((e1000e_enable_tx_pkt_filtering(hw)) &&
3052 (adapter->mng_vlan_id != adapter->hw.mng_cookie.vlan_id))
3053 e1000_update_mng_vlan(adapter);
3056 if (!netif_carrier_ok(netdev)) {
3058 /* update snapshot of PHY registers on LSC */
3059 e1000_phy_read_status(adapter);
3060 mac->ops.get_link_up_info(&adapter->hw,
3061 &adapter->link_speed,
3062 &adapter->link_duplex);
3063 e1000_print_link_info(adapter);
3065 * tweak tx_queue_len according to speed/duplex
3066 * and adjust the timeout factor
3068 netdev->tx_queue_len = adapter->tx_queue_len;
3069 adapter->tx_timeout_factor = 1;
3070 switch (adapter->link_speed) {
3073 netdev->tx_queue_len = 10;
3074 adapter->tx_timeout_factor = 14;
3078 netdev->tx_queue_len = 100;
3079 /* maybe add some timeout factor ? */
3084 * workaround: re-program speed mode bit after
3087 if ((adapter->flags & FLAG_TARC_SPEED_MODE_BIT) &&
3090 tarc0 = er32(TARC(0));
3091 tarc0 &= ~SPEED_MODE_BIT;
3092 ew32(TARC(0), tarc0);
3096 * disable TSO for pcie and 10/100 speeds, to avoid
3097 * some hardware issues
3099 if (!(adapter->flags & FLAG_TSO_FORCE)) {
3100 switch (adapter->link_speed) {
3104 "10/100 speed: disabling TSO\n");
3105 netdev->features &= ~NETIF_F_TSO;
3106 netdev->features &= ~NETIF_F_TSO6;
3109 netdev->features |= NETIF_F_TSO;
3110 netdev->features |= NETIF_F_TSO6;
3119 * enable transmits in the hardware, need to do this
3120 * after setting TARC(0)
3123 tctl |= E1000_TCTL_EN;
3126 netif_carrier_on(netdev);
3127 netif_wake_queue(netdev);
3129 if (!test_bit(__E1000_DOWN, &adapter->state))
3130 mod_timer(&adapter->phy_info_timer,
3131 round_jiffies(jiffies + 2 * HZ));
3134 if (netif_carrier_ok(netdev)) {
3135 adapter->link_speed = 0;
3136 adapter->link_duplex = 0;
3137 ndev_info(netdev, "Link is Down\n");
3138 netif_carrier_off(netdev);
3139 netif_stop_queue(netdev);
3140 if (!test_bit(__E1000_DOWN, &adapter->state))
3141 mod_timer(&adapter->phy_info_timer,
3142 round_jiffies(jiffies + 2 * HZ));
3144 if (adapter->flags & FLAG_RX_NEEDS_RESTART)
3145 schedule_work(&adapter->reset_task);
3150 e1000e_update_stats(adapter);
3152 mac->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old;
3153 adapter->tpt_old = adapter->stats.tpt;
3154 mac->collision_delta = adapter->stats.colc - adapter->colc_old;
3155 adapter->colc_old = adapter->stats.colc;
3157 adapter->gorc = adapter->stats.gorc - adapter->gorc_old;
3158 adapter->gorc_old = adapter->stats.gorc;
3159 adapter->gotc = adapter->stats.gotc - adapter->gotc_old;
3160 adapter->gotc_old = adapter->stats.gotc;
3162 e1000e_update_adaptive(&adapter->hw);
3164 if (!netif_carrier_ok(netdev)) {
3165 tx_pending = (e1000_desc_unused(tx_ring) + 1 <
3169 * We've lost link, so the controller stops DMA,
3170 * but we've got queued Tx work that's never going
3171 * to get done, so reset controller to flush Tx.
3172 * (Do the reset outside of interrupt context).
3174 adapter->tx_timeout_count++;
3175 schedule_work(&adapter->reset_task);
3179 /* Cause software interrupt to ensure Rx ring is cleaned */
3180 ew32(ICS, E1000_ICS_RXDMT0);
3182 /* Force detection of hung controller every watchdog period */
3183 adapter->detect_tx_hung = 1;
3186 * With 82571 controllers, LAA may be overwritten due to controller
3187 * reset from the other port. Set the appropriate LAA in RAR[0]
3189 if (e1000e_get_laa_state_82571(hw))
3190 e1000e_rar_set(hw, adapter->hw.mac.addr, 0);
3192 /* Reset the timer */
3193 if (!test_bit(__E1000_DOWN, &adapter->state))
3194 mod_timer(&adapter->watchdog_timer,
3195 round_jiffies(jiffies + 2 * HZ));
3198 #define E1000_TX_FLAGS_CSUM 0x00000001
3199 #define E1000_TX_FLAGS_VLAN 0x00000002
3200 #define E1000_TX_FLAGS_TSO 0x00000004
3201 #define E1000_TX_FLAGS_IPV4 0x00000008
3202 #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000
3203 #define E1000_TX_FLAGS_VLAN_SHIFT 16
3205 static int e1000_tso(struct e1000_adapter *adapter,
3206 struct sk_buff *skb)
3208 struct e1000_ring *tx_ring = adapter->tx_ring;
3209 struct e1000_context_desc *context_desc;
3210 struct e1000_buffer *buffer_info;
3213 u16 ipcse = 0, tucse, mss;
3214 u8 ipcss, ipcso, tucss, tucso, hdr_len;
3217 if (skb_is_gso(skb)) {
3218 if (skb_header_cloned(skb)) {
3219 err = pskb_expand_head(skb, 0, 0, GFP_ATOMIC);
3224 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
3225 mss = skb_shinfo(skb)->gso_size;
3226 if (skb->protocol == htons(ETH_P_IP)) {
3227 struct iphdr *iph = ip_hdr(skb);
3230 tcp_hdr(skb)->check = ~csum_tcpudp_magic(iph->saddr,
3234 cmd_length = E1000_TXD_CMD_IP;
3235 ipcse = skb_transport_offset(skb) - 1;
3236 } else if (skb_shinfo(skb)->gso_type == SKB_GSO_TCPV6) {
3237 ipv6_hdr(skb)->payload_len = 0;
3238 tcp_hdr(skb)->check =
3239 ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
3240 &ipv6_hdr(skb)->daddr,
3244 ipcss = skb_network_offset(skb);
3245 ipcso = (void *)&(ip_hdr(skb)->check) - (void *)skb->data;
3246 tucss = skb_transport_offset(skb);
3247 tucso = (void *)&(tcp_hdr(skb)->check) - (void *)skb->data;
3250 cmd_length |= (E1000_TXD_CMD_DEXT | E1000_TXD_CMD_TSE |
3251 E1000_TXD_CMD_TCP | (skb->len - (hdr_len)));
3253 i = tx_ring->next_to_use;
3254 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
3255 buffer_info = &tx_ring->buffer_info[i];
3257 context_desc->lower_setup.ip_fields.ipcss = ipcss;
3258 context_desc->lower_setup.ip_fields.ipcso = ipcso;
3259 context_desc->lower_setup.ip_fields.ipcse = cpu_to_le16(ipcse);
3260 context_desc->upper_setup.tcp_fields.tucss = tucss;
3261 context_desc->upper_setup.tcp_fields.tucso = tucso;
3262 context_desc->upper_setup.tcp_fields.tucse = cpu_to_le16(tucse);
3263 context_desc->tcp_seg_setup.fields.mss = cpu_to_le16(mss);
3264 context_desc->tcp_seg_setup.fields.hdr_len = hdr_len;
3265 context_desc->cmd_and_length = cpu_to_le32(cmd_length);
3267 buffer_info->time_stamp = jiffies;
3268 buffer_info->next_to_watch = i;
3271 if (i == tx_ring->count)
3273 tx_ring->next_to_use = i;
3281 static bool e1000_tx_csum(struct e1000_adapter *adapter, struct sk_buff *skb)
3283 struct e1000_ring *tx_ring = adapter->tx_ring;
3284 struct e1000_context_desc *context_desc;
3285 struct e1000_buffer *buffer_info;
3289 if (skb->ip_summed == CHECKSUM_PARTIAL) {
3290 css = skb_transport_offset(skb);
3292 i = tx_ring->next_to_use;
3293 buffer_info = &tx_ring->buffer_info[i];
3294 context_desc = E1000_CONTEXT_DESC(*tx_ring, i);
3296 context_desc->lower_setup.ip_config = 0;
3297 context_desc->upper_setup.tcp_fields.tucss = css;
3298 context_desc->upper_setup.tcp_fields.tucso =
3299 css + skb->csum_offset;
3300 context_desc->upper_setup.tcp_fields.tucse = 0;
3301 context_desc->tcp_seg_setup.data = 0;
3302 context_desc->cmd_and_length = cpu_to_le32(E1000_TXD_CMD_DEXT);
3304 buffer_info->time_stamp = jiffies;
3305 buffer_info->next_to_watch = i;
3308 if (i == tx_ring->count)
3310 tx_ring->next_to_use = i;
3318 #define E1000_MAX_PER_TXD 8192
3319 #define E1000_MAX_TXD_PWR 12
3321 static int e1000_tx_map(struct e1000_adapter *adapter,
3322 struct sk_buff *skb, unsigned int first,
3323 unsigned int max_per_txd, unsigned int nr_frags,
3326 struct e1000_ring *tx_ring = adapter->tx_ring;
3327 struct e1000_buffer *buffer_info;
3328 unsigned int len = skb->len - skb->data_len;
3329 unsigned int offset = 0, size, count = 0, i;
3332 i = tx_ring->next_to_use;
3335 buffer_info = &tx_ring->buffer_info[i];
3336 size = min(len, max_per_txd);
3338 /* Workaround for premature desc write-backs
3339 * in TSO mode. Append 4-byte sentinel desc */
3340 if (mss && !nr_frags && size == len && size > 8)
3343 buffer_info->length = size;
3344 /* set time_stamp *before* dma to help avoid a possible race */
3345 buffer_info->time_stamp = jiffies;
3347 pci_map_single(adapter->pdev,
3351 if (pci_dma_mapping_error(buffer_info->dma)) {
3352 dev_err(&adapter->pdev->dev, "TX DMA map failed\n");
3353 adapter->tx_dma_failed++;
3356 buffer_info->next_to_watch = i;
3362 if (i == tx_ring->count)
3366 for (f = 0; f < nr_frags; f++) {
3367 struct skb_frag_struct *frag;
3369 frag = &skb_shinfo(skb)->frags[f];
3371 offset = frag->page_offset;
3374 buffer_info = &tx_ring->buffer_info[i];
3375 size = min(len, max_per_txd);
3376 /* Workaround for premature desc write-backs
3377 * in TSO mode. Append 4-byte sentinel desc */
3378 if (mss && f == (nr_frags-1) && size == len && size > 8)
3381 buffer_info->length = size;
3382 buffer_info->time_stamp = jiffies;
3384 pci_map_page(adapter->pdev,
3389 if (pci_dma_mapping_error(buffer_info->dma)) {
3390 dev_err(&adapter->pdev->dev,
3391 "TX DMA page map failed\n");
3392 adapter->tx_dma_failed++;
3396 buffer_info->next_to_watch = i;
3403 if (i == tx_ring->count)
3409 i = tx_ring->count - 1;
3413 tx_ring->buffer_info[i].skb = skb;
3414 tx_ring->buffer_info[first].next_to_watch = i;
3419 static void e1000_tx_queue(struct e1000_adapter *adapter,
3420 int tx_flags, int count)
3422 struct e1000_ring *tx_ring = adapter->tx_ring;
3423 struct e1000_tx_desc *tx_desc = NULL;
3424 struct e1000_buffer *buffer_info;
3425 u32 txd_upper = 0, txd_lower = E1000_TXD_CMD_IFCS;
3428 if (tx_flags & E1000_TX_FLAGS_TSO) {
3429 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D |
3431 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
3433 if (tx_flags & E1000_TX_FLAGS_IPV4)
3434 txd_upper |= E1000_TXD_POPTS_IXSM << 8;
3437 if (tx_flags & E1000_TX_FLAGS_CSUM) {
3438 txd_lower |= E1000_TXD_CMD_DEXT | E1000_TXD_DTYP_D;
3439 txd_upper |= E1000_TXD_POPTS_TXSM << 8;
3442 if (tx_flags & E1000_TX_FLAGS_VLAN) {
3443 txd_lower |= E1000_TXD_CMD_VLE;
3444 txd_upper |= (tx_flags & E1000_TX_FLAGS_VLAN_MASK);
3447 i = tx_ring->next_to_use;
3450 buffer_info = &tx_ring->buffer_info[i];
3451 tx_desc = E1000_TX_DESC(*tx_ring, i);
3452 tx_desc->buffer_addr = cpu_to_le64(buffer_info->dma);
3453 tx_desc->lower.data =
3454 cpu_to_le32(txd_lower | buffer_info->length);
3455 tx_desc->upper.data = cpu_to_le32(txd_upper);
3458 if (i == tx_ring->count)
3462 tx_desc->lower.data |= cpu_to_le32(adapter->txd_cmd);
3465 * Force memory writes to complete before letting h/w
3466 * know there are new descriptors to fetch. (Only
3467 * applicable for weak-ordered memory model archs,
3472 tx_ring->next_to_use = i;
3473 writel(i, adapter->hw.hw_addr + tx_ring->tail);
3475 * we need this if more than one processor can write to our tail
3476 * at a time, it synchronizes IO on IA64/Altix systems
3481 #define MINIMUM_DHCP_PACKET_SIZE 282
3482 static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter,
3483 struct sk_buff *skb)
3485 struct e1000_hw *hw = &adapter->hw;
3488 if (vlan_tx_tag_present(skb)) {
3489 if (!((vlan_tx_tag_get(skb) == adapter->hw.mng_cookie.vlan_id)
3490 && (adapter->hw.mng_cookie.status &
3491 E1000_MNG_DHCP_COOKIE_STATUS_VLAN)))
3495 if (skb->len <= MINIMUM_DHCP_PACKET_SIZE)
3498 if (((struct ethhdr *) skb->data)->h_proto != htons(ETH_P_IP))
3502 const struct iphdr *ip = (struct iphdr *)((u8 *)skb->data+14);
3505 if (ip->protocol != IPPROTO_UDP)
3508 udp = (struct udphdr *)((u8 *)ip + (ip->ihl << 2));
3509 if (ntohs(udp->dest) != 67)
3512 offset = (u8 *)udp + 8 - skb->data;
3513 length = skb->len - offset;
3514 return e1000e_mng_write_dhcp_info(hw, (u8 *)udp + 8, length);
3520 static int __e1000_maybe_stop_tx(struct net_device *netdev, int size)
3522 struct e1000_adapter *adapter = netdev_priv(netdev);
3524 netif_stop_queue(netdev);
3526 * Herbert's original patch had:
3527 * smp_mb__after_netif_stop_queue();
3528 * but since that doesn't exist yet, just open code it.
3533 * We need to check again in a case another CPU has just
3534 * made room available.
3536 if (e1000_desc_unused(adapter->tx_ring) < size)
3540 netif_start_queue(netdev);
3541 ++adapter->restart_queue;
3545 static int e1000_maybe_stop_tx(struct net_device *netdev, int size)
3547 struct e1000_adapter *adapter = netdev_priv(netdev);
3549 if (e1000_desc_unused(adapter->tx_ring) >= size)
3551 return __e1000_maybe_stop_tx(netdev, size);
3554 #define TXD_USE_COUNT(S, X) (((S) >> (X)) + 1 )
3555 static int e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
3557 struct e1000_adapter *adapter = netdev_priv(netdev);
3558 struct e1000_ring *tx_ring = adapter->tx_ring;
3560 unsigned int max_per_txd = E1000_MAX_PER_TXD;
3561 unsigned int max_txd_pwr = E1000_MAX_TXD_PWR;
3562 unsigned int tx_flags = 0;
3563 unsigned int len = skb->len - skb->data_len;
3564 unsigned long irq_flags;
3565 unsigned int nr_frags;
3571 if (test_bit(__E1000_DOWN, &adapter->state)) {
3572 dev_kfree_skb_any(skb);
3573 return NETDEV_TX_OK;
3576 if (skb->len <= 0) {
3577 dev_kfree_skb_any(skb);
3578 return NETDEV_TX_OK;
3581 mss = skb_shinfo(skb)->gso_size;
3583 * The controller does a simple calculation to
3584 * make sure there is enough room in the FIFO before
3585 * initiating the DMA for each buffer. The calc is:
3586 * 4 = ceil(buffer len/mss). To make sure we don't
3587 * overrun the FIFO, adjust the max buffer len if mss
3592 max_per_txd = min(mss << 2, max_per_txd);
3593 max_txd_pwr = fls(max_per_txd) - 1;
3596 * TSO Workaround for 82571/2/3 Controllers -- if skb->data
3597 * points to just header, pull a few bytes of payload from
3598 * frags into skb->data
3600 hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb);
3602 * we do this workaround for ES2LAN, but it is un-necessary,
3603 * avoiding it could save a lot of cycles
3605 if (skb->data_len && (hdr_len == len)) {
3606 unsigned int pull_size;
3608 pull_size = min((unsigned int)4, skb->data_len);
3609 if (!__pskb_pull_tail(skb, pull_size)) {
3611 "__pskb_pull_tail failed.\n");
3612 dev_kfree_skb_any(skb);
3613 return NETDEV_TX_OK;
3615 len = skb->len - skb->data_len;
3619 /* reserve a descriptor for the offload context */
3620 if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
3624 count += TXD_USE_COUNT(len, max_txd_pwr);
3626 nr_frags = skb_shinfo(skb)->nr_frags;
3627 for (f = 0; f < nr_frags; f++)
3628 count += TXD_USE_COUNT(skb_shinfo(skb)->frags[f].size,
3631 if (adapter->hw.mac.tx_pkt_filtering)
3632 e1000_transfer_dhcp_info(adapter, skb);
3634 if (!spin_trylock_irqsave(&adapter->tx_queue_lock, irq_flags))
3635 /* Collision - tell upper layer to requeue */
3636 return NETDEV_TX_LOCKED;
3639 * need: count + 2 desc gap to keep tail from touching
3640 * head, otherwise try next time
3642 if (e1000_maybe_stop_tx(netdev, count + 2)) {
3643 spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
3644 return NETDEV_TX_BUSY;
3647 if (adapter->vlgrp && vlan_tx_tag_present(skb)) {
3648 tx_flags |= E1000_TX_FLAGS_VLAN;
3649 tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
3652 first = tx_ring->next_to_use;
3654 tso = e1000_tso(adapter, skb);
3656 dev_kfree_skb_any(skb);
3657 spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
3658 return NETDEV_TX_OK;
3662 tx_flags |= E1000_TX_FLAGS_TSO;
3663 else if (e1000_tx_csum(adapter, skb))
3664 tx_flags |= E1000_TX_FLAGS_CSUM;
3667 * Old method was to assume IPv4 packet by default if TSO was enabled.
3668 * 82571 hardware supports TSO capabilities for IPv6 as well...
3669 * no longer assume, we must.
3671 if (skb->protocol == htons(ETH_P_IP))
3672 tx_flags |= E1000_TX_FLAGS_IPV4;
3674 count = e1000_tx_map(adapter, skb, first, max_per_txd, nr_frags, mss);
3676 /* handle pci_map_single() error in e1000_tx_map */
3677 dev_kfree_skb_any(skb);
3678 spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
3679 return NETDEV_TX_OK;
3682 e1000_tx_queue(adapter, tx_flags, count);
3684 netdev->trans_start = jiffies;
3686 /* Make sure there is space in the ring for the next send. */
3687 e1000_maybe_stop_tx(netdev, MAX_SKB_FRAGS + 2);
3689 spin_unlock_irqrestore(&adapter->tx_queue_lock, irq_flags);
3690 return NETDEV_TX_OK;
3694 * e1000_tx_timeout - Respond to a Tx Hang
3695 * @netdev: network interface device structure
3697 static void e1000_tx_timeout(struct net_device *netdev)
3699 struct e1000_adapter *adapter = netdev_priv(netdev);
3701 /* Do the reset outside of interrupt context */
3702 adapter->tx_timeout_count++;
3703 schedule_work(&adapter->reset_task);
3706 static void e1000_reset_task(struct work_struct *work)
3708 struct e1000_adapter *adapter;
3709 adapter = container_of(work, struct e1000_adapter, reset_task);
3711 e1000e_reinit_locked(adapter);
3715 * e1000_get_stats - Get System Network Statistics
3716 * @netdev: network interface device structure
3718 * Returns the address of the device statistics structure.
3719 * The statistics are actually updated from the timer callback.
3721 static struct net_device_stats *e1000_get_stats(struct net_device *netdev)
3723 struct e1000_adapter *adapter = netdev_priv(netdev);
3725 /* only return the current stats */
3726 return &adapter->net_stats;
3730 * e1000_change_mtu - Change the Maximum Transfer Unit
3731 * @netdev: network interface device structure
3732 * @new_mtu: new value for maximum frame size
3734 * Returns 0 on success, negative on failure
3736 static int e1000_change_mtu(struct net_device *netdev, int new_mtu)
3738 struct e1000_adapter *adapter = netdev_priv(netdev);
3739 int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
3741 if ((max_frame < ETH_ZLEN + ETH_FCS_LEN) ||
3742 (max_frame > MAX_JUMBO_FRAME_SIZE)) {
3743 ndev_err(netdev, "Invalid MTU setting\n");
3747 /* Jumbo frame size limits */
3748 if (max_frame > ETH_FRAME_LEN + ETH_FCS_LEN) {
3749 if (!(adapter->flags & FLAG_HAS_JUMBO_FRAMES)) {
3750 ndev_err(netdev, "Jumbo Frames not supported.\n");
3753 if (adapter->hw.phy.type == e1000_phy_ife) {
3754 ndev_err(netdev, "Jumbo Frames not supported.\n");
3759 #define MAX_STD_JUMBO_FRAME_SIZE 9234
3760 if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) {
3761 ndev_err(netdev, "MTU > 9216 not supported.\n");
3765 while (test_and_set_bit(__E1000_RESETTING, &adapter->state))
3767 /* e1000e_down has a dependency on max_frame_size */
3768 adapter->max_frame_size = max_frame;
3769 if (netif_running(netdev))
3770 e1000e_down(adapter);
3773 * NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN
3774 * means we reserve 2 more, this pushes us to allocate from the next
3776 * i.e. RXBUFFER_2048 --> size-4096 slab
3777 * However with the new *_jumbo_rx* routines, jumbo receives will use
3781 if (max_frame <= 256)
3782 adapter->rx_buffer_len = 256;
3783 else if (max_frame <= 512)
3784 adapter->rx_buffer_len = 512;
3785 else if (max_frame <= 1024)
3786 adapter->rx_buffer_len = 1024;
3787 else if (max_frame <= 2048)
3788 adapter->rx_buffer_len = 2048;
3790 adapter->rx_buffer_len = 4096;
3792 /* adjust allocation if LPE protects us, and we aren't using SBP */
3793 if ((max_frame == ETH_FRAME_LEN + ETH_FCS_LEN) ||
3794 (max_frame == ETH_FRAME_LEN + VLAN_HLEN + ETH_FCS_LEN))
3795 adapter->rx_buffer_len = ETH_FRAME_LEN + VLAN_HLEN
3798 ndev_info(netdev, "changing MTU from %d to %d\n",
3799 netdev->mtu, new_mtu);
3800 netdev->mtu = new_mtu;
3802 if (netif_running(netdev))
3805 e1000e_reset(adapter);
3807 clear_bit(__E1000_RESETTING, &adapter->state);
3812 static int e1000_mii_ioctl(struct net_device *netdev, struct ifreq *ifr,
3815 struct e1000_adapter *adapter = netdev_priv(netdev);
3816 struct mii_ioctl_data *data = if_mii(ifr);
3818 if (adapter->hw.phy.media_type != e1000_media_type_copper)
3823 data->phy_id = adapter->hw.phy.addr;
3826 if (!capable(CAP_NET_ADMIN))
3828 switch (data->reg_num & 0x1F) {
3830 data->val_out = adapter->phy_regs.bmcr;
3833 data->val_out = adapter->phy_regs.bmsr;
3836 data->val_out = (adapter->hw.phy.id >> 16);
3839 data->val_out = (adapter->hw.phy.id & 0xFFFF);
3842 data->val_out = adapter->phy_regs.advertise;
3845 data->val_out = adapter->phy_regs.lpa;
3848 data->val_out = adapter->phy_regs.expansion;
3851 data->val_out = adapter->phy_regs.ctrl1000;
3854 data->val_out = adapter->phy_regs.stat1000;
3857 data->val_out = adapter->phy_regs.estatus;
3870 static int e1000_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
3876 return e1000_mii_ioctl(netdev, ifr, cmd);
3882 static int e1000_suspend(struct pci_dev *pdev, pm_message_t state)
3884 struct net_device *netdev = pci_get_drvdata(pdev);
3885 struct e1000_adapter *adapter = netdev_priv(netdev);
3886 struct e1000_hw *hw = &adapter->hw;
3887 u32 ctrl, ctrl_ext, rctl, status;
3888 u32 wufc = adapter->wol;
3891 netif_device_detach(netdev);
3893 if (netif_running(netdev)) {
3894 WARN_ON(test_bit(__E1000_RESETTING, &adapter->state));
3895 e1000e_down(adapter);
3896 e1000_free_irq(adapter);
3899 retval = pci_save_state(pdev);
3903 status = er32(STATUS);
3904 if (status & E1000_STATUS_LU)
3905 wufc &= ~E1000_WUFC_LNKC;
3908 e1000_setup_rctl(adapter);
3909 e1000_set_multi(netdev);
3911 /* turn on all-multi mode if wake on multicast is enabled */
3912 if (wufc & E1000_WUFC_MC) {
3914 rctl |= E1000_RCTL_MPE;
3919 /* advertise wake from D3Cold */
3920 #define E1000_CTRL_ADVD3WUC 0x00100000
3921 /* phy power management enable */
3922 #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000
3923 ctrl |= E1000_CTRL_ADVD3WUC |
3924 E1000_CTRL_EN_PHY_PWR_MGMT;
3927 if (adapter->hw.phy.media_type == e1000_media_type_fiber ||
3928 adapter->hw.phy.media_type ==
3929 e1000_media_type_internal_serdes) {
3930 /* keep the laser running in D3 */
3931 ctrl_ext = er32(CTRL_EXT);
3932 ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
3933 ew32(CTRL_EXT, ctrl_ext);
3936 if (adapter->flags & FLAG_IS_ICH)
3937 e1000e_disable_gig_wol_ich8lan(&adapter->hw);
3939 /* Allow time for pending master requests to run */
3940 e1000e_disable_pcie_master(&adapter->hw);
3942 ew32(WUC, E1000_WUC_PME_EN);
3944 pci_enable_wake(pdev, PCI_D3hot, 1);
3945 pci_enable_wake(pdev, PCI_D3cold, 1);
3949 pci_enable_wake(pdev, PCI_D3hot, 0);
3950 pci_enable_wake(pdev, PCI_D3cold, 0);
3953 /* make sure adapter isn't asleep if manageability is enabled */
3954 if (adapter->flags & FLAG_MNG_PT_ENABLED) {
3955 pci_enable_wake(pdev, PCI_D3hot, 1);
3956 pci_enable_wake(pdev, PCI_D3cold, 1);
3959 if (adapter->hw.phy.type == e1000_phy_igp_3)
3960 e1000e_igp3_phy_powerdown_workaround_ich8lan(&adapter->hw);
3963 * Release control of h/w to f/w. If f/w is AMT enabled, this
3964 * would have already happened in close and is redundant.
3966 e1000_release_hw_control(adapter);
3968 pci_disable_device(pdev);
3970 pci_set_power_state(pdev, pci_choose_state(pdev, state));
3975 static void e1000e_disable_l1aspm(struct pci_dev *pdev)
3981 * 82573 workaround - disable L1 ASPM on mobile chipsets
3983 * L1 ASPM on various mobile (ich7) chipsets do not behave properly
3984 * resulting in lost data or garbage information on the pci-e link
3985 * level. This could result in (false) bad EEPROM checksum errors,
3986 * long ping times (up to 2s) or even a system freeze/hang.
3988 * Unfortunately this feature saves about 1W power consumption when
3991 pos = pci_find_capability(pdev, PCI_CAP_ID_EXP);
3992 pci_read_config_word(pdev, pos + PCI_EXP_LNKCTL, &val);
3994 dev_warn(&pdev->dev, "Disabling L1 ASPM\n");
3996 pci_write_config_word(pdev, pos + PCI_EXP_LNKCTL, val);
4001 static int e1000_resume(struct pci_dev *pdev)
4003 struct net_device *netdev = pci_get_drvdata(pdev);
4004 struct e1000_adapter *adapter = netdev_priv(netdev);
4005 struct e1000_hw *hw = &adapter->hw;
4008 pci_set_power_state(pdev, PCI_D0);
4009 pci_restore_state(pdev);
4010 e1000e_disable_l1aspm(pdev);
4012 if (adapter->need_ioport)
4013 err = pci_enable_device(pdev);
4015 err = pci_enable_device_mem(pdev);
4018 "Cannot enable PCI device from suspend\n");
4022 pci_set_master(pdev);
4024 pci_enable_wake(pdev, PCI_D3hot, 0);
4025 pci_enable_wake(pdev, PCI_D3cold, 0);
4027 if (netif_running(netdev)) {
4028 err = e1000_request_irq(adapter);
4033 e1000e_power_up_phy(adapter);
4034 e1000e_reset(adapter);
4037 e1000_init_manageability(adapter);
4039 if (netif_running(netdev))
4042 netif_device_attach(netdev);
4045 * If the controller has AMT, do not set DRV_LOAD until the interface
4046 * is up. For all other cases, let the f/w know that the h/w is now
4047 * under the control of the driver.
4049 if (!(adapter->flags & FLAG_HAS_AMT) || !e1000e_check_mng_mode(&adapter->hw))
4050 e1000_get_hw_control(adapter);
4056 static void e1000_shutdown(struct pci_dev *pdev)
4058 e1000_suspend(pdev, PMSG_SUSPEND);
4061 #ifdef CONFIG_NET_POLL_CONTROLLER
4063 * Polling 'interrupt' - used by things like netconsole to send skbs
4064 * without having to re-enable interrupts. It's not called while
4065 * the interrupt routine is executing.
4067 static void e1000_netpoll(struct net_device *netdev)
4069 struct e1000_adapter *adapter = netdev_priv(netdev);
4071 disable_irq(adapter->pdev->irq);
4072 e1000_intr(adapter->pdev->irq, netdev);
4074 e1000_clean_tx_irq(adapter);
4076 enable_irq(adapter->pdev->irq);
4081 * e1000_io_error_detected - called when PCI error is detected
4082 * @pdev: Pointer to PCI device
4083 * @state: The current pci connection state
4085 * This function is called after a PCI bus error affecting
4086 * this device has been detected.
4088 static pci_ers_result_t e1000_io_error_detected(struct pci_dev *pdev,
4089 pci_channel_state_t state)
4091 struct net_device *netdev = pci_get_drvdata(pdev);
4092 struct e1000_adapter *adapter = netdev_priv(netdev);
4094 netif_device_detach(netdev);
4096 if (netif_running(netdev))
4097 e1000e_down(adapter);
4098 pci_disable_device(pdev);
4100 /* Request a slot slot reset. */
4101 return PCI_ERS_RESULT_NEED_RESET;
4105 * e1000_io_slot_reset - called after the pci bus has been reset.
4106 * @pdev: Pointer to PCI device
4108 * Restart the card from scratch, as if from a cold-boot. Implementation
4109 * resembles the first-half of the e1000_resume routine.
4111 static pci_ers_result_t e1000_io_slot_reset(struct pci_dev *pdev)
4113 struct net_device *netdev = pci_get_drvdata(pdev);
4114 struct e1000_adapter *adapter = netdev_priv(netdev);
4115 struct e1000_hw *hw = &adapter->hw;
4118 e1000e_disable_l1aspm(pdev);
4119 if (adapter->need_ioport)
4120 err = pci_enable_device(pdev);
4122 err = pci_enable_device_mem(pdev);
4125 "Cannot re-enable PCI device after reset.\n");
4126 return PCI_ERS_RESULT_DISCONNECT;
4128 pci_set_master(pdev);
4129 pci_restore_state(pdev);
4131 pci_enable_wake(pdev, PCI_D3hot, 0);
4132 pci_enable_wake(pdev, PCI_D3cold, 0);
4134 e1000e_reset(adapter);
4137 return PCI_ERS_RESULT_RECOVERED;
4141 * e1000_io_resume - called when traffic can start flowing again.
4142 * @pdev: Pointer to PCI device
4144 * This callback is called when the error recovery driver tells us that
4145 * its OK to resume normal operation. Implementation resembles the
4146 * second-half of the e1000_resume routine.
4148 static void e1000_io_resume(struct pci_dev *pdev)
4150 struct net_device *netdev = pci_get_drvdata(pdev);
4151 struct e1000_adapter *adapter = netdev_priv(netdev);
4153 e1000_init_manageability(adapter);
4155 if (netif_running(netdev)) {
4156 if (e1000e_up(adapter)) {
4158 "can't bring device back up after reset\n");
4163 netif_device_attach(netdev);
4166 * If the controller has AMT, do not set DRV_LOAD until the interface
4167 * is up. For all other cases, let the f/w know that the h/w is now
4168 * under the control of the driver.
4170 if (!(adapter->flags & FLAG_HAS_AMT) ||
4171 !e1000e_check_mng_mode(&adapter->hw))
4172 e1000_get_hw_control(adapter);
4176 static void e1000_print_device_info(struct e1000_adapter *adapter)
4178 struct e1000_hw *hw = &adapter->hw;
4179 struct net_device *netdev = adapter->netdev;
4182 /* print bus type/speed/width info */
4183 ndev_info(netdev, "(PCI Express:2.5GB/s:%s) "
4184 "%02x:%02x:%02x:%02x:%02x:%02x\n",
4186 ((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
4189 netdev->dev_addr[0], netdev->dev_addr[1],
4190 netdev->dev_addr[2], netdev->dev_addr[3],
4191 netdev->dev_addr[4], netdev->dev_addr[5]);
4192 ndev_info(netdev, "Intel(R) PRO/%s Network Connection\n",
4193 (hw->phy.type == e1000_phy_ife)
4194 ? "10/100" : "1000");
4195 e1000e_read_pba_num(hw, &pba_num);
4196 ndev_info(netdev, "MAC: %d, PHY: %d, PBA No: %06x-%03x\n",
4197 hw->mac.type, hw->phy.type,
4198 (pba_num >> 8), (pba_num & 0xff));
4202 * e1000e_is_need_ioport - determine if an adapter needs ioport resources or not
4203 * @pdev: PCI device information struct
4205 * Returns true if an adapters needs ioport resources
4207 static int e1000e_is_need_ioport(struct pci_dev *pdev)
4209 switch (pdev->device) {
4210 /* Currently there are no adapters that need ioport resources */
4217 * e1000_probe - Device Initialization Routine
4218 * @pdev: PCI device information struct
4219 * @ent: entry in e1000_pci_tbl
4221 * Returns 0 on success, negative on failure
4223 * e1000_probe initializes an adapter identified by a pci_dev structure.
4224 * The OS initialization, configuring of the adapter private structure,
4225 * and a hardware reset occur.
4227 static int __devinit e1000_probe(struct pci_dev *pdev,
4228 const struct pci_device_id *ent)
4230 struct net_device *netdev;
4231 struct e1000_adapter *adapter;
4232 struct e1000_hw *hw;
4233 const struct e1000_info *ei = e1000_info_tbl[ent->driver_data];
4234 resource_size_t mmio_start, mmio_len;
4235 resource_size_t flash_start, flash_len;
4237 static int cards_found;
4238 int i, err, pci_using_dac;
4239 u16 eeprom_data = 0;
4240 u16 eeprom_apme_mask = E1000_EEPROM_APME;
4241 int bars, need_ioport;
4243 e1000e_disable_l1aspm(pdev);
4245 /* do not allocate ioport bars when not needed */
4246 need_ioport = e1000e_is_need_ioport(pdev);
4248 bars = pci_select_bars(pdev, IORESOURCE_MEM | IORESOURCE_IO);
4249 err = pci_enable_device(pdev);
4251 bars = pci_select_bars(pdev, IORESOURCE_MEM);
4252 err = pci_enable_device_mem(pdev);
4258 err = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
4260 err = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
4264 err = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
4266 err = pci_set_consistent_dma_mask(pdev,
4269 dev_err(&pdev->dev, "No usable DMA "
4270 "configuration, aborting\n");
4276 err = pci_request_selected_regions(pdev, bars, e1000e_driver_name);
4280 pci_set_master(pdev);
4281 pci_save_state(pdev);
4284 netdev = alloc_etherdev(sizeof(struct e1000_adapter));
4286 goto err_alloc_etherdev;
4288 SET_NETDEV_DEV(netdev, &pdev->dev);
4290 pci_set_drvdata(pdev, netdev);
4291 adapter = netdev_priv(netdev);
4293 adapter->netdev = netdev;
4294 adapter->pdev = pdev;
4296 adapter->pba = ei->pba;
4297 adapter->flags = ei->flags;
4298 adapter->hw.adapter = adapter;
4299 adapter->hw.mac.type = ei->mac;
4300 adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1;
4301 adapter->bars = bars;
4302 adapter->need_ioport = need_ioport;
4304 mmio_start = pci_resource_start(pdev, 0);
4305 mmio_len = pci_resource_len(pdev, 0);
4308 adapter->hw.hw_addr = ioremap(mmio_start, mmio_len);
4309 if (!adapter->hw.hw_addr)
4312 if ((adapter->flags & FLAG_HAS_FLASH) &&
4313 (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) {
4314 flash_start = pci_resource_start(pdev, 1);
4315 flash_len = pci_resource_len(pdev, 1);
4316 adapter->hw.flash_address = ioremap(flash_start, flash_len);
4317 if (!adapter->hw.flash_address)
4321 /* construct the net_device struct */
4322 netdev->open = &e1000_open;
4323 netdev->stop = &e1000_close;
4324 netdev->hard_start_xmit = &e1000_xmit_frame;
4325 netdev->get_stats = &e1000_get_stats;
4326 netdev->set_multicast_list = &e1000_set_multi;
4327 netdev->set_mac_address = &e1000_set_mac;
4328 netdev->change_mtu = &e1000_change_mtu;
4329 netdev->do_ioctl = &e1000_ioctl;
4330 e1000e_set_ethtool_ops(netdev);
4331 netdev->tx_timeout = &e1000_tx_timeout;
4332 netdev->watchdog_timeo = 5 * HZ;
4333 netif_napi_add(netdev, &adapter->napi, e1000_clean, 64);
4334 netdev->vlan_rx_register = e1000_vlan_rx_register;
4335 netdev->vlan_rx_add_vid = e1000_vlan_rx_add_vid;
4336 netdev->vlan_rx_kill_vid = e1000_vlan_rx_kill_vid;
4337 #ifdef CONFIG_NET_POLL_CONTROLLER
4338 netdev->poll_controller = e1000_netpoll;
4340 strncpy(netdev->name, pci_name(pdev), sizeof(netdev->name) - 1);
4342 netdev->mem_start = mmio_start;
4343 netdev->mem_end = mmio_start + mmio_len;
4345 adapter->bd_number = cards_found++;
4347 /* setup adapter struct */
4348 err = e1000_sw_init(adapter);
4354 memcpy(&hw->mac.ops, ei->mac_ops, sizeof(hw->mac.ops));
4355 memcpy(&hw->nvm.ops, ei->nvm_ops, sizeof(hw->nvm.ops));
4356 memcpy(&hw->phy.ops, ei->phy_ops, sizeof(hw->phy.ops));
4358 err = ei->get_variants(adapter);
4362 hw->mac.ops.get_bus_info(&adapter->hw);
4364 adapter->hw.phy.autoneg_wait_to_complete = 0;
4366 /* Copper options */
4367 if (adapter->hw.phy.media_type == e1000_media_type_copper) {
4368 adapter->hw.phy.mdix = AUTO_ALL_MODES;
4369 adapter->hw.phy.disable_polarity_correction = 0;
4370 adapter->hw.phy.ms_type = e1000_ms_hw_default;
4373 if (e1000_check_reset_block(&adapter->hw))
4375 "PHY reset is blocked due to SOL/IDER session.\n");
4377 netdev->features = NETIF_F_SG |
4379 NETIF_F_HW_VLAN_TX |
4382 if (adapter->flags & FLAG_HAS_HW_VLAN_FILTER)
4383 netdev->features |= NETIF_F_HW_VLAN_FILTER;
4385 netdev->features |= NETIF_F_TSO;
4386 netdev->features |= NETIF_F_TSO6;
4388 netdev->vlan_features |= NETIF_F_TSO;
4389 netdev->vlan_features |= NETIF_F_TSO6;
4390 netdev->vlan_features |= NETIF_F_HW_CSUM;
4391 netdev->vlan_features |= NETIF_F_SG;
4394 netdev->features |= NETIF_F_HIGHDMA;
4397 * We should not be using LLTX anymore, but we are still Tx faster with
4400 netdev->features |= NETIF_F_LLTX;
4402 if (e1000e_enable_mng_pass_thru(&adapter->hw))
4403 adapter->flags |= FLAG_MNG_PT_ENABLED;
4406 * before reading the NVM, reset the controller to
4407 * put the device in a known good starting state
4409 adapter->hw.mac.ops.reset_hw(&adapter->hw);
4412 * systems with ASPM and others may see the checksum fail on the first
4413 * attempt. Let's give it a few tries
4416 if (e1000_validate_nvm_checksum(&adapter->hw) >= 0)
4419 ndev_err(netdev, "The NVM Checksum Is Not Valid\n");
4425 /* copy the MAC address out of the NVM */
4426 if (e1000e_read_mac_addr(&adapter->hw))
4427 ndev_err(netdev, "NVM Read Error while reading MAC address\n");
4429 memcpy(netdev->dev_addr, adapter->hw.mac.addr, netdev->addr_len);
4430 memcpy(netdev->perm_addr, adapter->hw.mac.addr, netdev->addr_len);
4432 if (!is_valid_ether_addr(netdev->perm_addr)) {
4433 ndev_err(netdev, "Invalid MAC Address: "
4434 "%02x:%02x:%02x:%02x:%02x:%02x\n",
4435 netdev->perm_addr[0], netdev->perm_addr[1],
4436 netdev->perm_addr[2], netdev->perm_addr[3],
4437 netdev->perm_addr[4], netdev->perm_addr[5]);
4442 init_timer(&adapter->watchdog_timer);
4443 adapter->watchdog_timer.function = &e1000_watchdog;
4444 adapter->watchdog_timer.data = (unsigned long) adapter;
4446 init_timer(&adapter->phy_info_timer);
4447 adapter->phy_info_timer.function = &e1000_update_phy_info;
4448 adapter->phy_info_timer.data = (unsigned long) adapter;
4450 INIT_WORK(&adapter->reset_task, e1000_reset_task);
4451 INIT_WORK(&adapter->watchdog_task, e1000_watchdog_task);
4453 e1000e_check_options(adapter);
4455 /* Initialize link parameters. User can change them with ethtool */
4456 adapter->hw.mac.autoneg = 1;
4457 adapter->fc_autoneg = 1;
4458 adapter->hw.fc.original_type = e1000_fc_default;
4459 adapter->hw.fc.type = e1000_fc_default;
4460 adapter->hw.phy.autoneg_advertised = 0x2f;
4462 /* ring size defaults */
4463 adapter->rx_ring->count = 256;
4464 adapter->tx_ring->count = 256;
4467 * Initial Wake on LAN setting - If APM wake is enabled in
4468 * the EEPROM, enable the ACPI Magic Packet filter
4470 if (adapter->flags & FLAG_APME_IN_WUC) {
4471 /* APME bit in EEPROM is mapped to WUC.APME */
4472 eeprom_data = er32(WUC);
4473 eeprom_apme_mask = E1000_WUC_APME;
4474 } else if (adapter->flags & FLAG_APME_IN_CTRL3) {
4475 if (adapter->flags & FLAG_APME_CHECK_PORT_B &&
4476 (adapter->hw.bus.func == 1))
4477 e1000_read_nvm(&adapter->hw,
4478 NVM_INIT_CONTROL3_PORT_B, 1, &eeprom_data);
4480 e1000_read_nvm(&adapter->hw,
4481 NVM_INIT_CONTROL3_PORT_A, 1, &eeprom_data);
4484 /* fetch WoL from EEPROM */
4485 if (eeprom_data & eeprom_apme_mask)
4486 adapter->eeprom_wol |= E1000_WUFC_MAG;
4489 * now that we have the eeprom settings, apply the special cases
4490 * where the eeprom may be wrong or the board simply won't support
4491 * wake on lan on a particular port
4493 if (!(adapter->flags & FLAG_HAS_WOL))
4494 adapter->eeprom_wol = 0;
4496 /* initialize the wol settings based on the eeprom settings */
4497 adapter->wol = adapter->eeprom_wol;
4499 /* reset the hardware with the new settings */
4500 e1000e_reset(adapter);
4503 * If the controller has AMT, do not set DRV_LOAD until the interface
4504 * is up. For all other cases, let the f/w know that the h/w is now
4505 * under the control of the driver.
4507 if (!(adapter->flags & FLAG_HAS_AMT) ||
4508 !e1000e_check_mng_mode(&adapter->hw))
4509 e1000_get_hw_control(adapter);
4511 /* tell the stack to leave us alone until e1000_open() is called */
4512 netif_carrier_off(netdev);
4513 netif_stop_queue(netdev);
4515 strcpy(netdev->name, "eth%d");
4516 err = register_netdev(netdev);
4520 e1000_print_device_info(adapter);
4526 e1000_release_hw_control(adapter);
4528 if (!e1000_check_reset_block(&adapter->hw))
4529 e1000_phy_hw_reset(&adapter->hw);
4531 if (adapter->hw.flash_address)
4532 iounmap(adapter->hw.flash_address);
4535 kfree(adapter->tx_ring);
4536 kfree(adapter->rx_ring);
4538 iounmap(adapter->hw.hw_addr);
4540 free_netdev(netdev);
4542 pci_release_selected_regions(pdev, bars);
4545 pci_disable_device(pdev);
4550 * e1000_remove - Device Removal Routine
4551 * @pdev: PCI device information struct
4553 * e1000_remove is called by the PCI subsystem to alert the driver
4554 * that it should release a PCI device. The could be caused by a
4555 * Hot-Plug event, or because the driver is going to be removed from
4558 static void __devexit e1000_remove(struct pci_dev *pdev)
4560 struct net_device *netdev = pci_get_drvdata(pdev);
4561 struct e1000_adapter *adapter = netdev_priv(netdev);
4564 * flush_scheduled work may reschedule our watchdog task, so
4565 * explicitly disable watchdog tasks from being rescheduled
4567 set_bit(__E1000_DOWN, &adapter->state);
4568 del_timer_sync(&adapter->watchdog_timer);
4569 del_timer_sync(&adapter->phy_info_timer);
4571 flush_scheduled_work();
4574 * Release control of h/w to f/w. If f/w is AMT enabled, this
4575 * would have already happened in close and is redundant.
4577 e1000_release_hw_control(adapter);
4579 unregister_netdev(netdev);
4581 if (!e1000_check_reset_block(&adapter->hw))
4582 e1000_phy_hw_reset(&adapter->hw);
4584 kfree(adapter->tx_ring);
4585 kfree(adapter->rx_ring);
4587 iounmap(adapter->hw.hw_addr);
4588 if (adapter->hw.flash_address)
4589 iounmap(adapter->hw.flash_address);
4590 pci_release_selected_regions(pdev, adapter->bars);
4592 free_netdev(netdev);
4594 pci_disable_device(pdev);
4597 /* PCI Error Recovery (ERS) */
4598 static struct pci_error_handlers e1000_err_handler = {
4599 .error_detected = e1000_io_error_detected,
4600 .slot_reset = e1000_io_slot_reset,
4601 .resume = e1000_io_resume,
4604 static struct pci_device_id e1000_pci_tbl[] = {
4605 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_COPPER), board_82571 },
4606 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_FIBER), board_82571 },
4607 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER), board_82571 },
4608 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_COPPER_LP), board_82571 },
4609 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_QUAD_FIBER), board_82571 },
4610 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES), board_82571 },
4611 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_DUAL), board_82571 },
4612 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571EB_SERDES_QUAD), board_82571 },
4613 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82571PT_QUAD_COPPER), board_82571 },
4615 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI), board_82572 },
4616 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_COPPER), board_82572 },
4617 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_FIBER), board_82572 },
4618 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82572EI_SERDES), board_82572 },
4620 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E), board_82573 },
4621 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573E_IAMT), board_82573 },
4622 { PCI_VDEVICE(INTEL, E1000_DEV_ID_82573L), board_82573 },
4624 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_DPT),
4625 board_80003es2lan },
4626 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_COPPER_SPT),
4627 board_80003es2lan },
4628 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_DPT),
4629 board_80003es2lan },
4630 { PCI_VDEVICE(INTEL, E1000_DEV_ID_80003ES2LAN_SERDES_SPT),
4631 board_80003es2lan },
4633 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE), board_ich8lan },
4634 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_G), board_ich8lan },
4635 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IFE_GT), board_ich8lan },
4636 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_AMT), board_ich8lan },
4637 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_C), board_ich8lan },
4638 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M), board_ich8lan },
4639 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH8_IGP_M_AMT), board_ich8lan },
4641 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE), board_ich9lan },
4642 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_G), board_ich9lan },
4643 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan },
4644 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan },
4645 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan },
4646 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan },
4647 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan },
4648 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan },
4650 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan },
4651 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan },
4652 { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan },
4654 { } /* terminate list */
4656 MODULE_DEVICE_TABLE(pci, e1000_pci_tbl);
4658 /* PCI Device API Driver */
4659 static struct pci_driver e1000_driver = {
4660 .name = e1000e_driver_name,
4661 .id_table = e1000_pci_tbl,
4662 .probe = e1000_probe,
4663 .remove = __devexit_p(e1000_remove),
4665 /* Power Management Hooks */
4666 .suspend = e1000_suspend,
4667 .resume = e1000_resume,
4669 .shutdown = e1000_shutdown,
4670 .err_handler = &e1000_err_handler
4674 * e1000_init_module - Driver Registration Routine
4676 * e1000_init_module is the first routine called when the driver is
4677 * loaded. All it does is register with the PCI subsystem.
4679 static int __init e1000_init_module(void)
4682 printk(KERN_INFO "%s: Intel(R) PRO/1000 Network Driver - %s\n",
4683 e1000e_driver_name, e1000e_driver_version);
4684 printk(KERN_INFO "%s: Copyright (c) 1999-2008 Intel Corporation.\n",
4685 e1000e_driver_name);
4686 ret = pci_register_driver(&e1000_driver);
4687 pm_qos_add_requirement(PM_QOS_CPU_DMA_LATENCY, e1000e_driver_name,
4688 PM_QOS_DEFAULT_VALUE);
4692 module_init(e1000_init_module);
4695 * e1000_exit_module - Driver Exit Cleanup Routine
4697 * e1000_exit_module is called just before the driver is removed
4700 static void __exit e1000_exit_module(void)
4702 pci_unregister_driver(&e1000_driver);
4703 pm_qos_remove_requirement(PM_QOS_CPU_DMA_LATENCY, e1000e_driver_name);
4705 module_exit(e1000_exit_module);
4708 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
4709 MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver");
4710 MODULE_LICENSE("GPL");
4711 MODULE_VERSION(DRV_VERSION);