2 * SuperH Mobile I2C Controller
4 * Copyright (C) 2014 Wolfram Sang <wsa@sang-engineering.com>
6 * Copyright (C) 2008 Magnus Damm
8 * Portions of the code based on out-of-tree driver i2c-sh7343.c
9 * Copyright (c) 2006 Carlos Munoz <carlos@kenati.com>
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
18 * GNU General Public License for more details.
21 #include <linux/clk.h>
22 #include <linux/delay.h>
23 #include <linux/dmaengine.h>
24 #include <linux/dma-mapping.h>
25 #include <linux/err.h>
26 #include <linux/i2c.h>
27 #include <linux/i2c/i2c-sh_mobile.h>
28 #include <linux/init.h>
29 #include <linux/interrupt.h>
31 #include <linux/kernel.h>
32 #include <linux/module.h>
33 #include <linux/of_device.h>
34 #include <linux/platform_device.h>
35 #include <linux/pm_runtime.h>
36 #include <linux/slab.h>
38 /* Transmit operation: */
41 /* BUS: S A8 ACK P(*) */
48 /* BUS: S A8 ACK D8(1) ACK P(*) */
49 /* IRQ: DTE WAIT WAIT */
55 /* BUS: S A8 ACK D8(1) ACK D8(2) ACK P(*) */
56 /* IRQ: DTE WAIT WAIT WAIT */
59 /* ICDR: A8 D8(1) D8(2) */
61 /* 3 bytes or more, +---------+ gets repeated */
64 /* Receive operation: */
66 /* 0 byte receive - not supported since slave may hold SDA low */
68 /* 1 byte receive [TX] | [RX] */
69 /* BUS: S A8 ACK | D8(1) ACK P(*) */
70 /* IRQ: DTE WAIT | WAIT DTE */
71 /* ICIC: -DTE | +DTE */
72 /* ICCR: 0x94 0x81 | 0xc0 */
73 /* ICDR: A8 | D8(1) */
75 /* 2 byte receive [TX]| [RX] */
76 /* BUS: S A8 ACK | D8(1) ACK D8(2) ACK P(*) */
77 /* IRQ: DTE WAIT | WAIT WAIT DTE */
78 /* ICIC: -DTE | +DTE */
79 /* ICCR: 0x94 0x81 | 0xc0 */
80 /* ICDR: A8 | D8(1) D8(2) */
82 /* 3 byte receive [TX] | [RX] (*) */
83 /* BUS: S A8 ACK | D8(1) ACK D8(2) ACK D8(3) ACK P */
84 /* IRQ: DTE WAIT | WAIT WAIT WAIT DTE */
85 /* ICIC: -DTE | +DTE */
86 /* ICCR: 0x94 0x81 | 0xc0 */
87 /* ICDR: A8 | D8(1) D8(2) D8(3) */
89 /* 4 bytes or more, this part is repeated +---------+ */
92 /* Interrupt order and BUSY flag */
94 /* SDA ___\___XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXAAAAAAAAA___/ */
95 /* SCL \_/1\_/2\_/3\_/4\_/5\_/6\_/7\_/8\___/9\_____/ */
97 /* S D7 D6 D5 D4 D3 D2 D1 D0 P(*) */
99 /* WAIT IRQ ________________________________/ \___________ */
100 /* TACK IRQ ____________________________________/ \_______ */
101 /* DTE IRQ __________________________________________/ \_ */
102 /* AL IRQ XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX */
103 /* _______________________________________________ */
106 /* (*) The STOP condition is only sent by the master at the end of the last */
107 /* I2C message or if the I2C_M_STOP flag is set. Similarly, the BUSY bit is */
108 /* only cleared after the STOP condition, so, between messages we have to */
109 /* poll for the DTE bit. */
112 enum sh_mobile_i2c_op {
124 struct sh_mobile_i2c_data {
127 struct i2c_adapter adap;
128 unsigned long bus_speed;
129 unsigned int clks_per_count;
137 wait_queue_head_t wait;
143 struct resource *res;
144 struct dma_chan *dma_tx;
145 struct dma_chan *dma_rx;
146 struct scatterlist sg;
147 enum dma_data_direction dma_direction;
150 struct sh_mobile_dt_config {
154 #define IIC_FLAG_HAS_ICIC67 (1 << 0)
156 #define STANDARD_MODE 100000
157 #define FAST_MODE 400000
159 /* Register offsets */
168 #define ICCR_ICE 0x80
169 #define ICCR_RACK 0x40
170 #define ICCR_TRS 0x10
171 #define ICCR_BBSY 0x04
172 #define ICCR_SCP 0x01
174 #define ICSR_SCLM 0x80
175 #define ICSR_SDAM 0x40
177 #define ICSR_BUSY 0x10
179 #define ICSR_TACK 0x04
180 #define ICSR_WAIT 0x02
181 #define ICSR_DTE 0x01
183 #define ICIC_ICCLB8 0x80
184 #define ICIC_ICCHB8 0x40
185 #define ICIC_TDMAE 0x20
186 #define ICIC_RDMAE 0x10
187 #define ICIC_ALE 0x08
188 #define ICIC_TACKE 0x04
189 #define ICIC_WAITE 0x02
190 #define ICIC_DTEE 0x01
192 static void iic_wr(struct sh_mobile_i2c_data *pd, int offs, unsigned char data)
197 iowrite8(data, pd->reg + offs);
200 static unsigned char iic_rd(struct sh_mobile_i2c_data *pd, int offs)
202 return ioread8(pd->reg + offs);
205 static void iic_set_clr(struct sh_mobile_i2c_data *pd, int offs,
206 unsigned char set, unsigned char clr)
208 iic_wr(pd, offs, (iic_rd(pd, offs) | set) & ~clr);
211 static u32 sh_mobile_i2c_iccl(unsigned long count_khz, u32 tLOW, u32 tf)
214 * Conditional expression:
215 * ICCL >= COUNT_CLK * (tLOW + tf)
217 * SH-Mobile IIC hardware starts counting the LOW period of
218 * the SCL signal (tLOW) as soon as it pulls the SCL line.
219 * In order to meet the tLOW timing spec, we need to take into
220 * account the fall time of SCL signal (tf). Default tf value
221 * should be 0.3 us, for safety.
223 return (((count_khz * (tLOW + tf)) + 5000) / 10000);
226 static u32 sh_mobile_i2c_icch(unsigned long count_khz, u32 tHIGH, u32 tf)
229 * Conditional expression:
230 * ICCH >= COUNT_CLK * (tHIGH + tf)
232 * SH-Mobile IIC hardware is aware of SCL transition period 'tr',
233 * and can ignore it. SH-Mobile IIC controller starts counting
234 * the HIGH period of the SCL signal (tHIGH) after the SCL input
235 * voltage increases at VIH.
237 * Afterward it turned out calculating ICCH using only tHIGH spec
238 * will result in violation of the tHD;STA timing spec. We need
239 * to take into account the fall time of SDA signal (tf) at START
240 * condition, in order to meet both tHIGH and tHD;STA specs.
242 return (((count_khz * (tHIGH + tf)) + 5000) / 10000);
245 static int sh_mobile_i2c_init(struct sh_mobile_i2c_data *pd)
247 unsigned long i2c_clk_khz;
251 /* Get clock rate after clock is enabled */
252 clk_prepare_enable(pd->clk);
253 i2c_clk_khz = clk_get_rate(pd->clk) / 1000;
254 clk_disable_unprepare(pd->clk);
255 i2c_clk_khz /= pd->clks_per_count;
257 if (pd->bus_speed == STANDARD_MODE) {
258 tLOW = 47; /* tLOW = 4.7 us */
259 tHIGH = 40; /* tHD;STA = tHIGH = 4.0 us */
260 tf = 3; /* tf = 0.3 us */
261 } else if (pd->bus_speed == FAST_MODE) {
262 tLOW = 13; /* tLOW = 1.3 us */
263 tHIGH = 6; /* tHD;STA = tHIGH = 0.6 us */
264 tf = 3; /* tf = 0.3 us */
266 dev_err(pd->dev, "unrecognized bus speed %lu Hz\n",
271 pd->iccl = sh_mobile_i2c_iccl(i2c_clk_khz, tLOW, tf);
272 pd->icch = sh_mobile_i2c_icch(i2c_clk_khz, tHIGH, tf);
274 max_val = pd->flags & IIC_FLAG_HAS_ICIC67 ? 0x1ff : 0xff;
275 if (pd->iccl > max_val || pd->icch > max_val) {
276 dev_err(pd->dev, "timing values out of range: L/H=0x%x/0x%x\n",
281 /* one more bit of ICCL in ICIC */
282 if (pd->iccl & 0x100)
283 pd->icic |= ICIC_ICCLB8;
285 pd->icic &= ~ICIC_ICCLB8;
287 /* one more bit of ICCH in ICIC */
288 if (pd->icch & 0x100)
289 pd->icic |= ICIC_ICCHB8;
291 pd->icic &= ~ICIC_ICCHB8;
293 dev_dbg(pd->dev, "timing values: L/H=0x%x/0x%x\n", pd->iccl, pd->icch);
297 static void activate_ch(struct sh_mobile_i2c_data *pd)
299 /* Wake up device and enable clock */
300 pm_runtime_get_sync(pd->dev);
301 clk_prepare_enable(pd->clk);
303 /* Enable channel and configure rx ack */
304 iic_set_clr(pd, ICCR, ICCR_ICE, 0);
306 /* Mask all interrupts */
310 iic_wr(pd, ICCL, pd->iccl & 0xff);
311 iic_wr(pd, ICCH, pd->icch & 0xff);
314 static void deactivate_ch(struct sh_mobile_i2c_data *pd)
316 /* Clear/disable interrupts */
320 /* Disable channel */
321 iic_set_clr(pd, ICCR, 0, ICCR_ICE);
323 /* Disable clock and mark device as idle */
324 clk_disable_unprepare(pd->clk);
325 pm_runtime_put_sync(pd->dev);
328 static unsigned char i2c_op(struct sh_mobile_i2c_data *pd,
329 enum sh_mobile_i2c_op op, unsigned char data)
331 unsigned char ret = 0;
334 dev_dbg(pd->dev, "op %d, data in 0x%02x\n", op, data);
336 spin_lock_irqsave(&pd->lock, flags);
339 case OP_START: /* issue start and trigger DTE interrupt */
340 iic_wr(pd, ICCR, ICCR_ICE | ICCR_TRS | ICCR_BBSY);
342 case OP_TX_FIRST: /* disable DTE interrupt and write data */
343 iic_wr(pd, ICIC, ICIC_WAITE | ICIC_ALE | ICIC_TACKE);
344 iic_wr(pd, ICDR, data);
346 case OP_TX: /* write data */
347 iic_wr(pd, ICDR, data);
349 case OP_TX_STOP_DATA: /* write data and issue a stop afterwards */
350 iic_wr(pd, ICDR, data);
352 case OP_TX_STOP: /* issue a stop */
353 iic_wr(pd, ICCR, pd->send_stop ? ICCR_ICE | ICCR_TRS
354 : ICCR_ICE | ICCR_TRS | ICCR_BBSY);
356 case OP_TX_TO_RX: /* select read mode */
357 iic_wr(pd, ICCR, ICCR_ICE | ICCR_SCP);
359 case OP_RX: /* just read data */
360 ret = iic_rd(pd, ICDR);
362 case OP_RX_STOP: /* enable DTE interrupt, issue stop */
364 ICIC_DTEE | ICIC_WAITE | ICIC_ALE | ICIC_TACKE);
365 iic_wr(pd, ICCR, ICCR_ICE | ICCR_RACK);
367 case OP_RX_STOP_DATA: /* enable DTE interrupt, read data, issue stop */
369 ICIC_DTEE | ICIC_WAITE | ICIC_ALE | ICIC_TACKE);
370 ret = iic_rd(pd, ICDR);
371 iic_wr(pd, ICCR, ICCR_ICE | ICCR_RACK);
375 spin_unlock_irqrestore(&pd->lock, flags);
377 dev_dbg(pd->dev, "op %d, data out 0x%02x\n", op, ret);
381 static bool sh_mobile_i2c_is_first_byte(struct sh_mobile_i2c_data *pd)
383 return pd->pos == -1;
386 static bool sh_mobile_i2c_is_last_byte(struct sh_mobile_i2c_data *pd)
388 return pd->pos == pd->msg->len - 1;
391 static void sh_mobile_i2c_get_data(struct sh_mobile_i2c_data *pd,
396 *buf = (pd->msg->addr & 0x7f) << 1;
397 *buf |= (pd->msg->flags & I2C_M_RD) ? 1 : 0;
400 *buf = pd->msg->buf[pd->pos];
404 static int sh_mobile_i2c_isr_tx(struct sh_mobile_i2c_data *pd)
408 if (pd->pos == pd->msg->len) {
409 /* Send stop if we haven't yet (DMA case) */
410 if (pd->send_stop && (iic_rd(pd, ICCR) & ICCR_BBSY))
411 i2c_op(pd, OP_TX_STOP, 0);
415 sh_mobile_i2c_get_data(pd, &data);
417 if (sh_mobile_i2c_is_last_byte(pd))
418 i2c_op(pd, OP_TX_STOP_DATA, data);
419 else if (sh_mobile_i2c_is_first_byte(pd))
420 i2c_op(pd, OP_TX_FIRST, data);
422 i2c_op(pd, OP_TX, data);
428 static int sh_mobile_i2c_isr_rx(struct sh_mobile_i2c_data *pd)
435 sh_mobile_i2c_get_data(pd, &data);
437 if (sh_mobile_i2c_is_first_byte(pd))
438 i2c_op(pd, OP_TX_FIRST, data);
440 i2c_op(pd, OP_TX, data);
445 i2c_op(pd, OP_TX_TO_RX, 0);
449 real_pos = pd->pos - 2;
451 if (pd->pos == pd->msg->len) {
453 i2c_op(pd, OP_RX_STOP, 0);
456 data = i2c_op(pd, OP_RX_STOP_DATA, 0);
458 data = i2c_op(pd, OP_RX, 0);
461 pd->msg->buf[real_pos] = data;
465 return pd->pos == (pd->msg->len + 2);
468 static irqreturn_t sh_mobile_i2c_isr(int irq, void *dev_id)
470 struct sh_mobile_i2c_data *pd = dev_id;
474 sr = iic_rd(pd, ICSR);
475 pd->sr |= sr; /* remember state */
477 dev_dbg(pd->dev, "i2c_isr 0x%02x 0x%02x %s %d %d!\n", sr, pd->sr,
478 (pd->msg->flags & I2C_M_RD) ? "read" : "write",
479 pd->pos, pd->msg->len);
481 /* Kick off TxDMA after preface was done */
482 if (pd->dma_direction == DMA_TO_DEVICE && pd->pos == 0)
483 iic_set_clr(pd, ICIC, ICIC_TDMAE, 0);
484 else if (sr & (ICSR_AL | ICSR_TACK))
485 /* don't interrupt transaction - continue to issue stop */
486 iic_wr(pd, ICSR, sr & ~(ICSR_AL | ICSR_TACK));
487 else if (pd->msg->flags & I2C_M_RD)
488 wakeup = sh_mobile_i2c_isr_rx(pd);
490 wakeup = sh_mobile_i2c_isr_tx(pd);
492 /* Kick off RxDMA after preface was done */
493 if (pd->dma_direction == DMA_FROM_DEVICE && pd->pos == 1)
494 iic_set_clr(pd, ICIC, ICIC_RDMAE, 0);
496 if (sr & ICSR_WAIT) /* TODO: add delay here to support slow acks */
497 iic_wr(pd, ICSR, sr & ~ICSR_WAIT);
504 /* defeat write posting to avoid spurious WAIT interrupts */
510 static void sh_mobile_i2c_dma_unmap(struct sh_mobile_i2c_data *pd)
512 struct dma_chan *chan = pd->dma_direction == DMA_FROM_DEVICE
513 ? pd->dma_rx : pd->dma_tx;
515 dma_unmap_single(chan->device->dev, sg_dma_address(&pd->sg),
516 pd->msg->len, pd->dma_direction);
518 pd->dma_direction = DMA_NONE;
521 static void sh_mobile_i2c_cleanup_dma(struct sh_mobile_i2c_data *pd)
523 if (pd->dma_direction == DMA_NONE)
525 else if (pd->dma_direction == DMA_FROM_DEVICE)
526 dmaengine_terminate_all(pd->dma_rx);
527 else if (pd->dma_direction == DMA_TO_DEVICE)
528 dmaengine_terminate_all(pd->dma_tx);
530 sh_mobile_i2c_dma_unmap(pd);
533 static void sh_mobile_i2c_dma_callback(void *data)
535 struct sh_mobile_i2c_data *pd = data;
537 sh_mobile_i2c_dma_unmap(pd);
538 pd->pos = pd->msg->len;
540 iic_set_clr(pd, ICIC, 0, ICIC_TDMAE | ICIC_RDMAE);
543 static struct dma_chan *sh_mobile_i2c_request_dma_chan(struct device *dev,
544 enum dma_transfer_direction dir, dma_addr_t port_addr)
546 struct dma_chan *chan;
547 struct dma_slave_config cfg;
548 char *chan_name = dir == DMA_MEM_TO_DEV ? "tx" : "rx";
551 chan = dma_request_slave_channel_reason(dev, chan_name);
554 dev_dbg(dev, "request_channel failed for %s (%d)\n", chan_name, ret);
558 memset(&cfg, 0, sizeof(cfg));
560 if (dir == DMA_MEM_TO_DEV) {
561 cfg.dst_addr = port_addr;
562 cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
564 cfg.src_addr = port_addr;
565 cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
568 ret = dmaengine_slave_config(chan, &cfg);
570 dev_dbg(dev, "slave_config failed for %s (%d)\n", chan_name, ret);
571 dma_release_channel(chan);
575 dev_dbg(dev, "got DMA channel for %s\n", chan_name);
579 static void sh_mobile_i2c_xfer_dma(struct sh_mobile_i2c_data *pd)
581 bool read = pd->msg->flags & I2C_M_RD;
582 enum dma_data_direction dir = read ? DMA_FROM_DEVICE : DMA_TO_DEVICE;
583 struct dma_chan *chan = read ? pd->dma_rx : pd->dma_tx;
584 struct dma_async_tx_descriptor *txdesc;
588 if (PTR_ERR(chan) == -EPROBE_DEFER) {
590 chan = pd->dma_rx = sh_mobile_i2c_request_dma_chan(pd->dev, DMA_DEV_TO_MEM,
591 pd->res->start + ICDR);
593 chan = pd->dma_tx = sh_mobile_i2c_request_dma_chan(pd->dev, DMA_MEM_TO_DEV,
594 pd->res->start + ICDR);
600 dma_addr = dma_map_single(chan->device->dev, pd->msg->buf, pd->msg->len, dir);
601 if (dma_mapping_error(pd->dev, dma_addr)) {
602 dev_dbg(pd->dev, "dma map failed, using PIO\n");
606 sg_dma_len(&pd->sg) = pd->msg->len;
607 sg_dma_address(&pd->sg) = dma_addr;
609 pd->dma_direction = dir;
611 txdesc = dmaengine_prep_slave_sg(chan, &pd->sg, 1,
612 read ? DMA_DEV_TO_MEM : DMA_MEM_TO_DEV,
613 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
615 dev_dbg(pd->dev, "dma prep slave sg failed, using PIO\n");
616 sh_mobile_i2c_cleanup_dma(pd);
620 txdesc->callback = sh_mobile_i2c_dma_callback;
621 txdesc->callback_param = pd;
623 cookie = dmaengine_submit(txdesc);
624 if (dma_submit_error(cookie)) {
625 dev_dbg(pd->dev, "submitting dma failed, using PIO\n");
626 sh_mobile_i2c_cleanup_dma(pd);
630 dma_async_issue_pending(chan);
633 static int start_ch(struct sh_mobile_i2c_data *pd, struct i2c_msg *usr_msg,
636 if (usr_msg->len == 0 && (usr_msg->flags & I2C_M_RD)) {
637 dev_err(pd->dev, "Unsupported zero length i2c read\n");
642 /* Initialize channel registers */
643 iic_set_clr(pd, ICCR, 0, ICCR_ICE);
645 /* Enable channel and configure rx ack */
646 iic_set_clr(pd, ICCR, ICCR_ICE, 0);
649 iic_wr(pd, ICCL, pd->iccl & 0xff);
650 iic_wr(pd, ICCH, pd->icch & 0xff);
657 if (pd->msg->len > 8)
658 sh_mobile_i2c_xfer_dma(pd);
660 /* Enable all interrupts to begin with */
661 iic_wr(pd, ICIC, ICIC_DTEE | ICIC_WAITE | ICIC_ALE | ICIC_TACKE);
665 static int poll_dte(struct sh_mobile_i2c_data *pd)
669 for (i = 1000; i; i--) {
670 u_int8_t val = iic_rd(pd, ICSR);
681 return i ? 0 : -ETIMEDOUT;
684 static int poll_busy(struct sh_mobile_i2c_data *pd)
688 for (i = 1000; i; i--) {
689 u_int8_t val = iic_rd(pd, ICSR);
691 dev_dbg(pd->dev, "val 0x%02x pd->sr 0x%02x\n", val, pd->sr);
693 /* the interrupt handler may wake us up before the
694 * transfer is finished, so poll the hardware
697 if (!(val & ICSR_BUSY)) {
698 /* handle missing acknowledge and arbitration lost */
710 return i ? 0 : -ETIMEDOUT;
713 static int sh_mobile_i2c_xfer(struct i2c_adapter *adapter,
714 struct i2c_msg *msgs,
717 struct sh_mobile_i2c_data *pd = i2c_get_adapdata(adapter);
724 /* Process all messages */
725 for (i = 0; i < num; i++) {
726 bool do_start = pd->send_stop || !i;
728 pd->send_stop = i == num - 1 || msg->flags & I2C_M_STOP;
730 err = start_ch(pd, msg, do_start);
735 i2c_op(pd, OP_START, 0);
737 /* The interrupt handler takes care of the rest... */
738 k = wait_event_timeout(pd->wait,
739 pd->sr & (ICSR_TACK | SW_DONE),
742 dev_err(pd->dev, "Transfer request timed out\n");
743 if (pd->dma_direction != DMA_NONE)
744 sh_mobile_i2c_cleanup_dma(pd);
765 static u32 sh_mobile_i2c_func(struct i2c_adapter *adapter)
767 return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_PROTOCOL_MANGLING;
770 static struct i2c_algorithm sh_mobile_i2c_algorithm = {
771 .functionality = sh_mobile_i2c_func,
772 .master_xfer = sh_mobile_i2c_xfer,
775 static const struct sh_mobile_dt_config default_dt_config = {
779 static const struct sh_mobile_dt_config fast_clock_dt_config = {
783 static const struct of_device_id sh_mobile_i2c_dt_ids[] = {
784 { .compatible = "renesas,rmobile-iic", .data = &default_dt_config },
785 { .compatible = "renesas,iic-r8a73a4", .data = &fast_clock_dt_config },
786 { .compatible = "renesas,iic-r8a7790", .data = &fast_clock_dt_config },
787 { .compatible = "renesas,iic-r8a7791", .data = &fast_clock_dt_config },
788 { .compatible = "renesas,iic-r8a7792", .data = &fast_clock_dt_config },
789 { .compatible = "renesas,iic-r8a7793", .data = &fast_clock_dt_config },
790 { .compatible = "renesas,iic-r8a7794", .data = &fast_clock_dt_config },
791 { .compatible = "renesas,iic-sh73a0", .data = &fast_clock_dt_config },
794 MODULE_DEVICE_TABLE(of, sh_mobile_i2c_dt_ids);
796 static void sh_mobile_i2c_release_dma(struct sh_mobile_i2c_data *pd)
798 if (!IS_ERR(pd->dma_tx)) {
799 dma_release_channel(pd->dma_tx);
800 pd->dma_tx = ERR_PTR(-EPROBE_DEFER);
803 if (!IS_ERR(pd->dma_rx)) {
804 dma_release_channel(pd->dma_rx);
805 pd->dma_rx = ERR_PTR(-EPROBE_DEFER);
809 static int sh_mobile_i2c_hook_irqs(struct platform_device *dev, struct sh_mobile_i2c_data *pd)
811 struct resource *res;
815 while ((res = platform_get_resource(dev, IORESOURCE_IRQ, k))) {
816 for (n = res->start; n <= res->end; n++) {
817 ret = devm_request_irq(&dev->dev, n, sh_mobile_i2c_isr,
818 0, dev_name(&dev->dev), pd);
820 dev_err(&dev->dev, "cannot request IRQ %pa\n", &n);
827 return k > 0 ? 0 : -ENOENT;
830 static int sh_mobile_i2c_probe(struct platform_device *dev)
832 struct i2c_sh_mobile_platform_data *pdata = dev_get_platdata(&dev->dev);
833 struct sh_mobile_i2c_data *pd;
834 struct i2c_adapter *adap;
835 struct resource *res;
839 pd = devm_kzalloc(&dev->dev, sizeof(struct sh_mobile_i2c_data), GFP_KERNEL);
843 pd->clk = devm_clk_get(&dev->dev, NULL);
844 if (IS_ERR(pd->clk)) {
845 dev_err(&dev->dev, "cannot get clock\n");
846 return PTR_ERR(pd->clk);
849 ret = sh_mobile_i2c_hook_irqs(dev, pd);
854 platform_set_drvdata(dev, pd);
856 res = platform_get_resource(dev, IORESOURCE_MEM, 0);
859 pd->reg = devm_ioremap_resource(&dev->dev, res);
861 return PTR_ERR(pd->reg);
863 /* Use platform data bus speed or STANDARD_MODE */
864 ret = of_property_read_u32(dev->dev.of_node, "clock-frequency", &bus_speed);
865 pd->bus_speed = ret ? STANDARD_MODE : bus_speed;
867 pd->clks_per_count = 1;
869 if (dev->dev.of_node) {
870 const struct of_device_id *match;
872 match = of_match_device(sh_mobile_i2c_dt_ids, &dev->dev);
874 const struct sh_mobile_dt_config *config;
876 config = match->data;
877 pd->clks_per_count = config->clks_per_count;
880 if (pdata && pdata->bus_speed)
881 pd->bus_speed = pdata->bus_speed;
882 if (pdata && pdata->clks_per_count)
883 pd->clks_per_count = pdata->clks_per_count;
886 /* The IIC blocks on SH-Mobile ARM processors
887 * come with two new bits in ICIC.
889 if (resource_size(res) > 0x17)
890 pd->flags |= IIC_FLAG_HAS_ICIC67;
892 ret = sh_mobile_i2c_init(pd);
897 sg_init_table(&pd->sg, 1);
898 pd->dma_direction = DMA_NONE;
899 pd->dma_rx = pd->dma_tx = ERR_PTR(-EPROBE_DEFER);
901 /* Enable Runtime PM for this device.
903 * Also tell the Runtime PM core to ignore children
904 * for this device since it is valid for us to suspend
905 * this I2C master driver even though the slave devices
906 * on the I2C bus may not be suspended.
908 * The state of the I2C hardware bus is unaffected by
909 * the Runtime PM state.
911 pm_suspend_ignore_children(&dev->dev, true);
912 pm_runtime_enable(&dev->dev);
914 /* setup the private data */
916 i2c_set_adapdata(adap, pd);
918 adap->owner = THIS_MODULE;
919 adap->algo = &sh_mobile_i2c_algorithm;
920 adap->dev.parent = &dev->dev;
923 adap->dev.of_node = dev->dev.of_node;
925 strlcpy(adap->name, dev->name, sizeof(adap->name));
927 spin_lock_init(&pd->lock);
928 init_waitqueue_head(&pd->wait);
930 ret = i2c_add_numbered_adapter(adap);
932 sh_mobile_i2c_release_dma(pd);
933 dev_err(&dev->dev, "cannot add numbered adapter\n");
937 dev_info(&dev->dev, "I2C adapter %d, bus speed %lu Hz\n", adap->nr, pd->bus_speed);
942 static int sh_mobile_i2c_remove(struct platform_device *dev)
944 struct sh_mobile_i2c_data *pd = platform_get_drvdata(dev);
946 i2c_del_adapter(&pd->adap);
947 sh_mobile_i2c_release_dma(pd);
948 pm_runtime_disable(&dev->dev);
952 static int sh_mobile_i2c_runtime_nop(struct device *dev)
954 /* Runtime PM callback shared between ->runtime_suspend()
955 * and ->runtime_resume(). Simply returns success.
957 * This driver re-initializes all registers after
958 * pm_runtime_get_sync() anyway so there is no need
959 * to save and restore registers here.
964 static const struct dev_pm_ops sh_mobile_i2c_dev_pm_ops = {
965 .runtime_suspend = sh_mobile_i2c_runtime_nop,
966 .runtime_resume = sh_mobile_i2c_runtime_nop,
969 static struct platform_driver sh_mobile_i2c_driver = {
971 .name = "i2c-sh_mobile",
972 .pm = &sh_mobile_i2c_dev_pm_ops,
973 .of_match_table = sh_mobile_i2c_dt_ids,
975 .probe = sh_mobile_i2c_probe,
976 .remove = sh_mobile_i2c_remove,
979 static int __init sh_mobile_i2c_adap_init(void)
981 return platform_driver_register(&sh_mobile_i2c_driver);
983 subsys_initcall(sh_mobile_i2c_adap_init);
985 static void __exit sh_mobile_i2c_adap_exit(void)
987 platform_driver_unregister(&sh_mobile_i2c_driver);
989 module_exit(sh_mobile_i2c_adap_exit);
991 MODULE_DESCRIPTION("SuperH Mobile I2C Bus Controller driver");
992 MODULE_AUTHOR("Magnus Damm and Wolfram Sang");
993 MODULE_LICENSE("GPL v2");
994 MODULE_ALIAS("platform:i2c-sh_mobile");