arch/blackfin/mach-bf537/boards/stamp.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2 or later.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/kernel.h>
  11 #include <linux/platform_device.h>
  12 #include <linux/io.h>
  13 #include <linux/mtd/mtd.h>
  14 #include <linux/mtd/nand.h>
  15 #include <linux/mtd/partitions.h>
  16 #include <linux/mtd/plat-ram.h>
  17 #include <linux/mtd/physmap.h>
  18 #include <linux/spi/spi.h>
  19 #include <linux/spi/flash.h>
  20 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
  21 #include <linux/usb/isp1362.h>
  22 #endif
  23 #include <linux/ata_platform.h>
  24 #include <linux/irq.h>
  25 #include <linux/interrupt.h>
  26 #include <linux/i2c.h>
  27 #include <linux/usb/sl811.h>
  28 #include <linux/spi/mmc_spi.h>
  29 #include <linux/leds.h>
  30 #include <linux/input.h>
  31 #include <asm/dma.h>
  32 #include <asm/bfin5xx_spi.h>
  33 #include <asm/reboot.h>
  34 #include <asm/portmux.h>
  35 #include <asm/dpmc.h>
  36
  37 /*
  38  * Name the Board for the /proc/cpuinfo
  39  */
  40 const char bfin_board_name[] = "ADI BF537-STAMP";
  41
  42 /*
  43  *  Driver needs to know address, irq and flag pin.
  44  */
  45
  46 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  47 #include <linux/usb/isp1760.h>
  48 static struct resource bfin_isp1760_resources[] = {
  49         [0] = {
  50                 .start  = 0x203C0000,
  51                 .end    = 0x203C0000 + 0x000fffff,
  52                 .flags  = IORESOURCE_MEM,
  53         },
  54         [1] = {
  55                 .start  = IRQ_PF7,
  56                 .end    = IRQ_PF7,
  57                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
  58         },
  59 };
  60
  61 static struct isp1760_platform_data isp1760_priv = {
  62         .is_isp1761 = 0,
  63         .bus_width_16 = 1,
  64         .port1_otg = 0,
  65         .analog_oc = 0,
  66         .dack_polarity_high = 0,
  67         .dreq_polarity_high = 0,
  68 };
  69
  70 static struct platform_device bfin_isp1760_device = {
  71         .name           = "isp1760",
  72         .id             = 0,
  73         .dev = {
  74                 .platform_data = &isp1760_priv,
  75         },
  76         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  77         .resource       = bfin_isp1760_resources,
  78 };
  79 #endif
  80
  81 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
  82 #include <linux/gpio_keys.h>
  83
  84 static struct gpio_keys_button bfin_gpio_keys_table[] = {
  85         {BTN_0, GPIO_PF2, 1, "gpio-keys: BTN0"},
  86         {BTN_1, GPIO_PF3, 1, "gpio-keys: BTN1"},
  87         {BTN_2, GPIO_PF4, 1, "gpio-keys: BTN2"},
  88         {BTN_3, GPIO_PF5, 1, "gpio-keys: BTN3"},
  89 };
  90
  91 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
  92         .buttons        = bfin_gpio_keys_table,
  93         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
  94 };
  95
  96 static struct platform_device bfin_device_gpiokeys = {
  97         .name      = "gpio-keys",
  98         .dev = {
  99                 .platform_data = &bfin_gpio_keys_data,
 100         },
 101 };
 102 #endif
 103
 104 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 105 static struct resource bfin_pcmcia_cf_resources[] = {
 106         {
 107                 .start = 0x20310000, /* IO PORT */
 108                 .end = 0x20312000,
 109                 .flags = IORESOURCE_MEM,
 110         }, {
 111                 .start = 0x20311000, /* Attribute Memory */
 112                 .end = 0x20311FFF,
 113                 .flags = IORESOURCE_MEM,
 114         }, {
 115                 .start = IRQ_PF4,
 116                 .end = IRQ_PF4,
 117                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 118         }, {
 119                 .start = 6, /* Card Detect PF6 */
 120                 .end = 6,
 121                 .flags = IORESOURCE_IRQ,
 122         },
 123 };
 124
 125 static struct platform_device bfin_pcmcia_cf_device = {
 126         .name = "bfin_cf_pcmcia",
 127         .id = -1,
 128         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 129         .resource = bfin_pcmcia_cf_resources,
 130 };
 131 #endif
 132
 133 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 134 static struct platform_device rtc_device = {
 135         .name = "rtc-bfin",
 136         .id   = -1,
 137 };
 138 #endif
 139
 140 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 141 #include <linux/smc91x.h>
 142
 143 static struct smc91x_platdata smc91x_info = {
 144         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 145         .leda = RPC_LED_100_10,
 146         .ledb = RPC_LED_TX_RX,
 147 };
 148
 149 static struct resource smc91x_resources[] = {
 150         {
 151                 .name = "smc91x-regs",
 152                 .start = 0x20300300,
 153                 .end = 0x20300300 + 16,
 154                 .flags = IORESOURCE_MEM,
 155         }, {
 156
 157                 .start = IRQ_PF7,
 158                 .end = IRQ_PF7,
 159                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 160         },
 161 };
 162 static struct platform_device smc91x_device = {
 163         .name = "smc91x",
 164         .id = 0,
 165         .num_resources = ARRAY_SIZE(smc91x_resources),
 166         .resource = smc91x_resources,
 167         .dev    = {
 168                 .platform_data  = &smc91x_info,
 169         },
 170 };
 171 #endif
 172
 173 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 174 static struct resource dm9000_resources[] = {
 175         [0] = {
 176                 .start  = 0x203FB800,
 177                 .end    = 0x203FB800 + 1,
 178                 .flags  = IORESOURCE_MEM,
 179         },
 180         [1] = {
 181                 .start  = 0x203FB804,
 182                 .end    = 0x203FB804 + 1,
 183                 .flags  = IORESOURCE_MEM,
 184         },
 185         [2] = {
 186                 .start  = IRQ_PF9,
 187                 .end    = IRQ_PF9,
 188                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 189         },
 190 };
 191
 192 static struct platform_device dm9000_device = {
 193         .name           = "dm9000",
 194         .id             = -1,
 195         .num_resources  = ARRAY_SIZE(dm9000_resources),
 196         .resource       = dm9000_resources,
 197 };
 198 #endif
 199
 200 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
 201 static struct resource sl811_hcd_resources[] = {
 202         {
 203                 .start = 0x20340000,
 204                 .end = 0x20340000,
 205                 .flags = IORESOURCE_MEM,
 206         }, {
 207                 .start = 0x20340004,
 208                 .end = 0x20340004,
 209                 .flags = IORESOURCE_MEM,
 210         }, {
 211                 .start = CONFIG_USB_SL811_BFIN_IRQ,
 212                 .end = CONFIG_USB_SL811_BFIN_IRQ,
 213                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 214         },
 215 };
 216
 217 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 218 void sl811_port_power(struct device *dev, int is_on)
 219 {
 220         gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
 221         gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
 222 }
 223 #endif
 224
 225 static struct sl811_platform_data sl811_priv = {
 226         .potpg = 10,
 227         .power = 250,       /* == 500mA */
 228 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 229         .port_power = &sl811_port_power,
 230 #endif
 231 };
 232
 233 static struct platform_device sl811_hcd_device = {
 234         .name = "sl811-hcd",
 235         .id = 0,
 236         .dev = {
 237                 .platform_data = &sl811_priv,
 238         },
 239         .num_resources = ARRAY_SIZE(sl811_hcd_resources),
 240         .resource = sl811_hcd_resources,
 241 };
 242 #endif
 243
 244 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 245 static struct resource isp1362_hcd_resources[] = {
 246         {
 247                 .start = 0x20360000,
 248                 .end = 0x20360000,
 249                 .flags = IORESOURCE_MEM,
 250         }, {
 251                 .start = 0x20360004,
 252                 .end = 0x20360004,
 253                 .flags = IORESOURCE_MEM,
 254         }, {
 255                 .start = IRQ_PF3,
 256                 .end = IRQ_PF3,
 257                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 258         },
 259 };
 260
 261 static struct isp1362_platform_data isp1362_priv = {
 262         .sel15Kres = 1,
 263         .clknotstop = 0,
 264         .oc_enable = 0,
 265         .int_act_high = 0,
 266         .int_edge_triggered = 0,
 267         .remote_wakeup_connected = 0,
 268         .no_power_switching = 1,
 269         .power_switching_mode = 0,
 270 };
 271
 272 static struct platform_device isp1362_hcd_device = {
 273         .name = "isp1362-hcd",
 274         .id = 0,
 275         .dev = {
 276                 .platform_data = &isp1362_priv,
 277         },
 278         .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 279         .resource = isp1362_hcd_resources,
 280 };
 281 #endif
 282
 283 #if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
 284 unsigned short bfin_can_peripherals[] = {
 285         P_CAN0_RX, P_CAN0_TX, 0
 286 };
 287
 288 static struct resource bfin_can_resources[] = {
 289         {
 290                 .start = 0xFFC02A00,
 291                 .end = 0xFFC02FFF,
 292                 .flags = IORESOURCE_MEM,
 293         },
 294         {
 295                 .start = IRQ_CAN_RX,
 296                 .end = IRQ_CAN_RX,
 297                 .flags = IORESOURCE_IRQ,
 298         },
 299         {
 300                 .start = IRQ_CAN_TX,
 301                 .end = IRQ_CAN_TX,
 302                 .flags = IORESOURCE_IRQ,
 303         },
 304         {
 305                 .start = IRQ_CAN_ERROR,
 306                 .end = IRQ_CAN_ERROR,
 307                 .flags = IORESOURCE_IRQ,
 308         },
 309 };
 310
 311 static struct platform_device bfin_can_device = {
 312         .name = "bfin_can",
 313         .num_resources = ARRAY_SIZE(bfin_can_resources),
 314         .resource = bfin_can_resources,
 315         .dev = {
 316                 .platform_data = &bfin_can_peripherals, /* Passed to driver */
 317         },
 318 };
 319 #endif
 320
 321 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 322 static struct platform_device bfin_mii_bus = {
 323         .name = "bfin_mii_bus",
 324 };
 325
 326 static struct platform_device bfin_mac_device = {
 327         .name = "bfin_mac",
 328         .dev.platform_data = &bfin_mii_bus,
 329 };
 330 #endif
 331
 332 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 333 static struct resource net2272_bfin_resources[] = {
 334         {
 335                 .start = 0x20300000,
 336                 .end = 0x20300000 + 0x100,
 337                 .flags = IORESOURCE_MEM,
 338         }, {
 339                 .start = IRQ_PF7,
 340                 .end = IRQ_PF7,
 341                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 342         },
 343 };
 344
 345 static struct platform_device net2272_bfin_device = {
 346         .name = "net2272",
 347         .id = -1,
 348         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 349         .resource = net2272_bfin_resources,
 350 };
 351 #endif
 352
 353 #if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 354 #ifdef CONFIG_MTD_PARTITIONS
 355 const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL };
 356
 357 static struct mtd_partition bfin_plat_nand_partitions[] = {
 358         {
 359                 .name   = "linux kernel(nand)",
 360                 .size   = 0x400000,
 361                 .offset = 0,
 362         }, {
 363                 .name   = "file system(nand)",
 364                 .size   = MTDPART_SIZ_FULL,
 365                 .offset = MTDPART_OFS_APPEND,
 366         },
 367 };
 368 #endif
 369
 370 #define BFIN_NAND_PLAT_CLE 2
 371 #define BFIN_NAND_PLAT_ALE 1
 372 static void bfin_plat_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 373 {
 374         struct nand_chip *this = mtd->priv;
 375
 376         if (cmd == NAND_CMD_NONE)
 377                 return;
 378
 379         if (ctrl & NAND_CLE)
 380                 writeb(cmd, this->IO_ADDR_W + (1 << BFIN_NAND_PLAT_CLE));
 381         else
 382                 writeb(cmd, this->IO_ADDR_W + (1 << BFIN_NAND_PLAT_ALE));
 383 }
 384
 385 #define BFIN_NAND_PLAT_READY GPIO_PF3
 386 static int bfin_plat_nand_dev_ready(struct mtd_info *mtd)
 387 {
 388         return gpio_get_value(BFIN_NAND_PLAT_READY);
 389 }
 390
 391 static struct platform_nand_data bfin_plat_nand_data = {
 392         .chip = {
 393                 .chip_delay = 30,
 394 #ifdef CONFIG_MTD_PARTITIONS
 395                 .part_probe_types = part_probes,
 396                 .partitions = bfin_plat_nand_partitions,
 397                 .nr_partitions = ARRAY_SIZE(bfin_plat_nand_partitions),
 398 #endif
 399         },
 400         .ctrl = {
 401                 .cmd_ctrl  = bfin_plat_nand_cmd_ctrl,
 402                 .dev_ready = bfin_plat_nand_dev_ready,
 403         },
 404 };
 405
 406 #define MAX(x, y) (x > y ? x : y)
 407 static struct resource bfin_plat_nand_resources = {
 408         .start = 0x20212000,
 409         .end   = 0x20212000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
 410         .flags = IORESOURCE_IO,
 411 };
 412
 413 static struct platform_device bfin_async_nand_device = {
 414         .name = "gen_nand",
 415         .id = -1,
 416         .num_resources = 1,
 417         .resource = &bfin_plat_nand_resources,
 418         .dev = {
 419                 .platform_data = &bfin_plat_nand_data,
 420         },
 421 };
 422
 423 static void bfin_plat_nand_init(void)
 424 {
 425         gpio_request(BFIN_NAND_PLAT_READY, "bfin_nand_plat");
 426 }
 427 #else
 428 static void bfin_plat_nand_init(void) {}
 429 #endif
 430
 431 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 432 static struct mtd_partition stamp_partitions[] = {
 433         {
 434                 .name       = "bootloader(nor)",
 435                 .size       = 0x40000,
 436                 .offset     = 0,
 437         }, {
 438                 .name       = "linux kernel(nor)",
 439                 .size       = 0x180000,
 440                 .offset     = MTDPART_OFS_APPEND,
 441         }, {
 442                 .name       = "file system(nor)",
 443                 .size       = 0x400000 - 0x40000 - 0x180000 - 0x10000,
 444                 .offset     = MTDPART_OFS_APPEND,
 445         }, {
 446                 .name       = "MAC Address(nor)",
 447                 .size       = MTDPART_SIZ_FULL,
 448                 .offset     = 0x3F0000,
 449                 .mask_flags = MTD_WRITEABLE,
 450         }
 451 };
 452
 453 static struct physmap_flash_data stamp_flash_data = {
 454         .width      = 2,
 455         .parts      = stamp_partitions,
 456         .nr_parts   = ARRAY_SIZE(stamp_partitions),
 457 };
 458
 459 static struct resource stamp_flash_resource = {
 460         .start = 0x20000000,
 461         .end   = 0x203fffff,
 462         .flags = IORESOURCE_MEM,
 463 };
 464
 465 static struct platform_device stamp_flash_device = {
 466         .name          = "physmap-flash",
 467         .id            = 0,
 468         .dev = {
 469                 .platform_data = &stamp_flash_data,
 470         },
 471         .num_resources = 1,
 472         .resource      = &stamp_flash_resource,
 473 };
 474 #endif
 475
 476 #if defined(CONFIG_MTD_M25P80) \
 477         || defined(CONFIG_MTD_M25P80_MODULE)
 478 static struct mtd_partition bfin_spi_flash_partitions[] = {
 479         {
 480                 .name = "bootloader(spi)",
 481                 .size = 0x00040000,
 482                 .offset = 0,
 483                 .mask_flags = MTD_CAP_ROM
 484         }, {
 485                 .name = "linux kernel(spi)",
 486                 .size = 0x180000,
 487                 .offset = MTDPART_OFS_APPEND,
 488         }, {
 489                 .name = "file system(spi)",
 490                 .size = MTDPART_SIZ_FULL,
 491                 .offset = MTDPART_OFS_APPEND,
 492         }
 493 };
 494
 495 static struct flash_platform_data bfin_spi_flash_data = {
 496         .name = "m25p80",
 497         .parts = bfin_spi_flash_partitions,
 498         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 499         /* .type = "m25p64", */
 500 };
 501
 502 /* SPI flash chip (m25p64) */
 503 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 504         .enable_dma = 0,         /* use dma transfer with this chip*/
 505         .bits_per_word = 8,
 506 };
 507 #endif
 508
 509 #if defined(CONFIG_BFIN_SPI_ADC) \
 510         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 511 /* SPI ADC chip */
 512 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 513         .enable_dma = 1,         /* use dma transfer with this chip*/
 514         .bits_per_word = 16,
 515 };
 516 #endif
 517
 518 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 519         || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 520 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 521         .enable_dma = 0,
 522         .bits_per_word = 16,
 523 };
 524 #endif
 525
 526 #if defined(CONFIG_SND_BF5XX_SOC_AD1938) \
 527         || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
 528 static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 529         .enable_dma = 0,
 530         .bits_per_word = 8,
 531 };
 532 #endif
 533
 534 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 535 #include <linux/input/ad714x.h>
 536 static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
 537         .enable_dma = 0,
 538         .bits_per_word = 16,
 539 };
 540
 541 static struct ad714x_slider_plat ad7147_spi_slider_plat[] = {
 542         {
 543                 .start_stage = 0,
 544                 .end_stage = 7,
 545                 .max_coord = 128,
 546         },
 547 };
 548
 549 static struct ad714x_button_plat ad7147_spi_button_plat[] = {
 550         {
 551                 .keycode = BTN_FORWARD,
 552                 .l_mask = 0,
 553                 .h_mask = 0x600,
 554         },
 555         {
 556                 .keycode = BTN_LEFT,
 557                 .l_mask = 0,
 558                 .h_mask = 0x500,
 559         },
 560         {
 561                 .keycode = BTN_MIDDLE,
 562                 .l_mask = 0,
 563                 .h_mask = 0x800,
 564         },
 565         {
 566                 .keycode = BTN_RIGHT,
 567                 .l_mask = 0x100,
 568                 .h_mask = 0x400,
 569         },
 570         {
 571                 .keycode = BTN_BACK,
 572                 .l_mask = 0x200,
 573                 .h_mask = 0x400,
 574         },
 575 };
 576 static struct ad714x_platform_data ad7147_spi_platform_data = {
 577         .slider_num = 1,
 578         .button_num = 5,
 579         .slider = ad7147_spi_slider_plat,
 580         .button = ad7147_spi_button_plat,
 581         .stage_cfg_reg =  {
 582                 {0xFBFF, 0x1FFF, 0, 0x2626, 1600, 1600, 1600, 1600},
 583                 {0xEFFF, 0x1FFF, 0, 0x2626, 1650, 1650, 1650, 1650},
 584                 {0xFFFF, 0x1FFE, 0, 0x2626, 1650, 1650, 1650, 1650},
 585                 {0xFFFF, 0x1FFB, 0, 0x2626, 1650, 1650, 1650, 1650},
 586                 {0xFFFF, 0x1FEF, 0, 0x2626, 1650, 1650, 1650, 1650},
 587                 {0xFFFF, 0x1FBF, 0, 0x2626, 1650, 1650, 1650, 1650},
 588                 {0xFFFF, 0x1EFF, 0, 0x2626, 1650, 1650, 1650, 1650},
 589                 {0xFFFF, 0x1BFF, 0, 0x2626, 1600, 1600, 1600, 1600},
 590                 {0xFF7B, 0x3FFF, 0x506,  0x2626, 1100, 1100, 1150, 1150},
 591                 {0xFDFE, 0x3FFF, 0x606,  0x2626, 1100, 1100, 1150, 1150},
 592                 {0xFEBA, 0x1FFF, 0x1400, 0x2626, 1200, 1200, 1300, 1300},
 593                 {0xFFEF, 0x1FFF, 0x0,    0x2626, 1100, 1100, 1150, 1150},
 594         },
 595         .sys_cfg_reg = {0x2B2, 0x0, 0x3233, 0x819, 0x832, 0xCFF, 0xCFF, 0x0},
 596 };
 597 #endif
 598
 599 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
 600 #include <linux/input/ad714x.h>
 601 static struct ad714x_button_plat ad7142_i2c_button_plat[] = {
 602         {
 603                 .keycode = BTN_1,
 604                 .l_mask = 0,
 605                 .h_mask = 0x1,
 606         },
 607         {
 608                 .keycode = BTN_2,
 609                 .l_mask = 0,
 610                 .h_mask = 0x2,
 611         },
 612         {
 613                 .keycode = BTN_3,
 614                 .l_mask = 0,
 615                 .h_mask = 0x4,
 616         },
 617         {
 618                 .keycode = BTN_4,
 619                 .l_mask = 0x0,
 620                 .h_mask = 0x8,
 621         },
 622 };
 623 static struct ad714x_platform_data ad7142_i2c_platform_data = {
 624         .button_num = 4,
 625         .button = ad7142_i2c_button_plat,
 626         .stage_cfg_reg =  {
 627                 /* fixme: figure out right setting for all comoponent according
 628                  * to hardware feature of EVAL-AD7142EB board */
 629                 {0xE7FF, 0x3FFF, 0x0005, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 630                 {0xFDBF, 0x3FFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 631                 {0xFFFF, 0x2DFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 632                 {0xFFFF, 0x37BF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 633                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 634                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 635                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 636                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 637                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 638                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 639                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 640                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 641         },
 642         .sys_cfg_reg = {0x0B2, 0x0, 0x690, 0x664, 0x290F, 0xF, 0xF, 0x0},
 643 };
 644 #endif
 645
 646 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 647 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 648
 649 static int bfin_mmc_spi_init(struct device *dev,
 650         irqreturn_t (*detect_int)(int, void *), void *data)
 651 {
 652         return request_irq(MMC_SPI_CARD_DETECT_INT, detect_int,
 653                 IRQF_TRIGGER_FALLING, "mmc-spi-detect", data);
 654 }
 655
 656 static void bfin_mmc_spi_exit(struct device *dev, void *data)
 657 {
 658         free_irq(MMC_SPI_CARD_DETECT_INT, data);
 659 }
 660
 661 static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
 662         .init = bfin_mmc_spi_init,
 663         .exit = bfin_mmc_spi_exit,
 664         .detect_delay = 100, /* msecs */
 665 };
 666
 667 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 668         .enable_dma = 0,
 669         .bits_per_word = 8,
 670         .pio_interrupt = 0,
 671 };
 672 #endif
 673
 674 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 675 #include <linux/spi/ad7877.h>
 676 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 677         .enable_dma = 0,
 678         .bits_per_word = 16,
 679 };
 680
 681 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 682         .model                  = 7877,
 683         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 684         .x_plate_ohms           = 419,
 685         .y_plate_ohms           = 486,
 686         .pressure_max           = 1000,
 687         .pressure_min           = 0,
 688         .stopacq_polarity       = 1,
 689         .first_conversion_delay = 3,
 690         .acquisition_time       = 1,
 691         .averaging              = 1,
 692         .pen_down_acc_interval  = 1,
 693 };
 694 #endif
 695
 696 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 697 #include <linux/spi/ad7879.h>
 698 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 699         .model                  = 7879, /* Model = AD7879 */
 700         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 701         .pressure_max           = 10000,
 702         .pressure_min           = 0,
 703         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 704         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 705         .median                 = 2,    /* do 8 measurements */
 706         .averaging              = 1,    /* take the average of 4 middle samples */
 707         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 708         .gpio_export            = 1,    /* Export GPIO to gpiolib */
 709         .gpio_base              = -1,   /* Dynamic allocation */
 710 };
 711 #endif
 712
 713 #if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
 714 #include <linux/input/adxl34x.h>
 715 static const struct adxl34x_platform_data adxl34x_info = {
 716         .x_axis_offset = 0,
 717         .y_axis_offset = 0,
 718         .z_axis_offset = 0,
 719         .tap_threshold = 0x31,
 720         .tap_duration = 0x10,
 721         .tap_latency = 0x60,
 722         .tap_window = 0xF0,
 723         .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
 724         .act_axis_control = 0xFF,
 725         .activity_threshold = 5,
 726         .inactivity_threshold = 3,
 727         .inactivity_time = 4,
 728         .free_fall_threshold = 0x7,
 729         .free_fall_time = 0x20,
 730         .data_rate = 0x8,
 731         .data_range = ADXL_FULL_RES,
 732
 733         .ev_type = EV_ABS,
 734         .ev_code_x = ABS_X,             /* EV_REL */
 735         .ev_code_y = ABS_Y,             /* EV_REL */
 736         .ev_code_z = ABS_Z,             /* EV_REL */
 737
 738         .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
 739
 740 /*      .ev_code_ff = KEY_F,*/          /* EV_KEY */
 741 /*      .ev_code_act_inactivity = KEY_A,*/      /* EV_KEY */
 742         .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
 743         .fifo_mode = ADXL_FIFO_STREAM,
 744 };
 745 #endif
 746
 747 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 748 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 749         .enable_dma = 0,
 750         .bits_per_word = 16,
 751 };
 752 #endif
 753
 754 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 755 static struct bfin5xx_spi_chip spidev_chip_info = {
 756         .enable_dma = 0,
 757         .bits_per_word = 8,
 758 };
 759 #endif
 760
 761 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 762 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 763         .enable_dma     = 0,
 764         .bits_per_word  = 8,
 765 };
 766 #endif
 767
 768 #if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
 769 static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
 770         .enable_dma     = 1,
 771         .bits_per_word  = 8,
 772         .cs_gpio = GPIO_PF10,
 773 };
 774 #endif
 775
 776 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
 777 static struct bfin5xx_spi_chip adf7021_spi_chip_info = {
 778         .bits_per_word = 16,
 779         .cs_gpio = GPIO_PF10,
 780 };
 781
 782 #include <linux/spi/adf702x.h>
 783 #define TXREG 0x0160A470
 784 static const u32 adf7021_regs[] = {
 785         0x09608FA0,
 786         0x00575011,
 787         0x00A7F092,
 788         0x2B141563,
 789         0x81F29E94,
 790         0x00003155,
 791         0x050A4F66,
 792         0x00000007,
 793         0x00000008,
 794         0x000231E9,
 795         0x3296354A,
 796         0x891A2B3B,
 797         0x00000D9C,
 798         0x0000000D,
 799         0x0000000E,
 800         0x0000000F,
 801 };
 802
 803 static struct adf702x_platform_data adf7021_platform_data = {
 804         .regs_base = (void *)SPORT1_TCR1,
 805         .dma_ch_rx = CH_SPORT1_RX,
 806         .dma_ch_tx = CH_SPORT1_TX,
 807         .irq_sport_err = IRQ_SPORT1_ERROR,
 808         .gpio_int_rfs = GPIO_PF8,
 809         .pin_req = {P_SPORT1_DTPRI, P_SPORT1_RFS, P_SPORT1_DRPRI,
 810                         P_SPORT1_RSCLK, P_SPORT1_TSCLK, 0},
 811         .adf702x_model = MODEL_ADF7021,
 812         .adf702x_regs = adf7021_regs,
 813         .tx_reg = TXREG,
 814 };
 815 #endif
 816
 817 #if defined(CONFIG_MTD_DATAFLASH) \
 818         || defined(CONFIG_MTD_DATAFLASH_MODULE)
 819
 820 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
 821         {
 822                 .name = "bootloader(spi)",
 823                 .size = 0x00040000,
 824                 .offset = 0,
 825                 .mask_flags = MTD_CAP_ROM
 826         }, {
 827                 .name = "linux kernel(spi)",
 828                 .size = 0x180000,
 829                 .offset = MTDPART_OFS_APPEND,
 830         }, {
 831                 .name = "file system(spi)",
 832                 .size = MTDPART_SIZ_FULL,
 833                 .offset = MTDPART_OFS_APPEND,
 834         }
 835 };
 836
 837 static struct flash_platform_data bfin_spi_dataflash_data = {
 838         .name = "SPI Dataflash",
 839         .parts = bfin_spi_dataflash_partitions,
 840         .nr_parts = ARRAY_SIZE(bfin_spi_dataflash_partitions),
 841 };
 842
 843 /* DataFlash chip */
 844 static struct bfin5xx_spi_chip data_flash_chip_info = {
 845         .enable_dma = 0,         /* use dma transfer with this chip*/
 846         .bits_per_word = 8,
 847 };
 848 #endif
 849
 850 #if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
 851 static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
 852         .enable_dma = 0,         /* use dma transfer with this chip*/
 853         .bits_per_word = 8,
 854 };
 855 #endif
 856
 857 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 858 #if defined(CONFIG_MTD_M25P80) \
 859         || defined(CONFIG_MTD_M25P80_MODULE)
 860         {
 861                 /* the modalias must be the same as spi device driver name */
 862                 .modalias = "m25p80", /* Name of spi_driver for this device */
 863                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 864                 .bus_num = 0, /* Framework bus number */
 865                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 866                 .platform_data = &bfin_spi_flash_data,
 867                 .controller_data = &spi_flash_chip_info,
 868                 .mode = SPI_MODE_3,
 869         },
 870 #endif
 871 #if defined(CONFIG_MTD_DATAFLASH) \
 872         || defined(CONFIG_MTD_DATAFLASH_MODULE)
 873         {       /* DataFlash chip */
 874                 .modalias = "mtd_dataflash",
 875                 .max_speed_hz = 33250000,     /* max spi clock (SCK) speed in HZ */
 876                 .bus_num = 0, /* Framework bus number */
 877                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 878                 .platform_data = &bfin_spi_dataflash_data,
 879                 .controller_data = &data_flash_chip_info,
 880                 .mode = SPI_MODE_3,
 881         },
 882 #endif
 883 #if defined(CONFIG_BFIN_SPI_ADC) \
 884         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 885         {
 886                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 887                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 888                 .bus_num = 0, /* Framework bus number */
 889                 .chip_select = 1, /* Framework chip select. */
 890                 .platform_data = NULL, /* No spi_driver specific config */
 891                 .controller_data = &spi_adc_chip_info,
 892         },
 893 #endif
 894
 895 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 896         || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 897         {
 898                 .modalias = "ad1836",
 899                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 900                 .bus_num = 0,
 901                 .chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
 902                 .controller_data = &ad1836_spi_chip_info,
 903                 .mode = SPI_MODE_3,
 904         },
 905 #endif
 906
 907 #if defined(CONFIG_SND_BF5XX_SOC_AD1938) || defined(CONFIG_SND_BF5XX_SOC_AD1938_MODULE)
 908         {
 909                 .modalias = "ad1938",
 910                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 911                 .bus_num = 0,
 912                 .chip_select = 5,
 913                 .controller_data = &ad1938_spi_chip_info,
 914                 .mode = SPI_MODE_3,
 915         },
 916 #endif
 917
 918 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 919         {
 920                 .modalias = "ad714x_captouch",
 921                 .max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
 922                 .irq = IRQ_PF4,
 923                 .bus_num = 0,
 924                 .chip_select = 5,
 925                 .mode = SPI_MODE_3,
 926                 .platform_data = &ad7147_spi_platform_data,
 927                 .controller_data = &ad7147_spi_chip_info,
 928         },
 929 #endif
 930
 931 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 932         {
 933                 .modalias = "mmc_spi",
 934                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 935                 .bus_num = 0,
 936                 .chip_select = 4,
 937                 .platform_data = &bfin_mmc_spi_pdata,
 938                 .controller_data = &mmc_spi_chip_info,
 939                 .mode = SPI_MODE_3,
 940         },
 941 #endif
 942 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 943         {
 944                 .modalias               = "ad7877",
 945                 .platform_data          = &bfin_ad7877_ts_info,
 946                 .irq                    = IRQ_PF6,
 947                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
 948                 .bus_num        = 0,
 949                 .chip_select  = 1,
 950                 .controller_data = &spi_ad7877_chip_info,
 951         },
 952 #endif
 953 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 954         {
 955                 .modalias = "ad7879",
 956                 .platform_data = &bfin_ad7879_ts_info,
 957                 .irq = IRQ_PF7,
 958                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 959                 .bus_num = 0,
 960                 .chip_select = 1,
 961                 .controller_data = &spi_ad7879_chip_info,
 962                 .mode = SPI_CPHA | SPI_CPOL,
 963         },
 964 #endif
 965 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 966         {
 967                 .modalias = "spidev",
 968                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 969                 .bus_num = 0,
 970                 .chip_select = 1,
 971                 .controller_data = &spidev_chip_info,
 972         },
 973 #endif
 974 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 975         {
 976                 .modalias = "bfin-lq035q1-spi",
 977                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 978                 .bus_num = 0,
 979                 .chip_select = 2,
 980                 .controller_data = &lq035q1_spi_chip_info,
 981                 .mode = SPI_CPHA | SPI_CPOL,
 982         },
 983 #endif
 984 #if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
 985         {
 986                 .modalias = "enc28j60",
 987                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 988                 .irq = IRQ_PF6,
 989                 .bus_num = 0,
 990                 .chip_select = 0,       /* GPIO controlled SSEL */
 991                 .controller_data = &enc28j60_spi_chip_info,
 992                 .mode = SPI_MODE_0,
 993         },
 994 #endif
 995 #if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
 996         {
 997                 .modalias       = "adxl34x",
 998                 .platform_data  = &adxl34x_info,
 999                 .irq            = IRQ_PF6,
1000                 .max_speed_hz   = 5000000,    /* max spi clock (SCK) speed in HZ */
1001                 .bus_num        = 0,
1002                 .chip_select    = 2,
1003                 .controller_data = &spi_adxl34x_chip_info,
1004                 .mode = SPI_MODE_3,
1005         },
1006 #endif
1007 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
1008         {
1009                 .modalias = "adf702x",
1010                 .max_speed_hz = 16000000,     /* max spi clock (SCK) speed in HZ */
1011                 .bus_num = 0,
1012                 .chip_select = 0,       /* GPIO controlled SSEL */
1013                 .controller_data = &adf7021_spi_chip_info,
1014                 .platform_data = &adf7021_platform_data,
1015                 .mode = SPI_MODE_0,
1016         },
1017 #endif
1018
1019 };
1020
1021 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1022 /* SPI controller data */
1023 static struct bfin5xx_spi_master bfin_spi0_info = {
1024         .num_chipselect = 8,
1025         .enable_dma = 1,  /* master has the ability to do dma transfer */
1026         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
1027 };
1028
1029 /* SPI (0) */
1030 static struct resource bfin_spi0_resource[] = {
1031         [0] = {
1032                 .start = SPI0_REGBASE,
1033                 .end   = SPI0_REGBASE + 0xFF,
1034                 .flags = IORESOURCE_MEM,
1035                 },
1036         [1] = {
1037                 .start = CH_SPI,
1038                 .end   = CH_SPI,
1039                 .flags = IORESOURCE_DMA,
1040         },
1041         [2] = {
1042                 .start = IRQ_SPI,
1043                 .end   = IRQ_SPI,
1044                 .flags = IORESOURCE_IRQ,
1045         },
1046 };
1047
1048 static struct platform_device bfin_spi0_device = {
1049         .name = "bfin-spi",
1050         .id = 0, /* Bus number */
1051         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
1052         .resource = bfin_spi0_resource,
1053         .dev = {
1054                 .platform_data = &bfin_spi0_info, /* Passed to driver */
1055         },
1056 };
1057 #endif  /* spi master and devices */
1058
1059 #if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
1060
1061 /* SPORT SPI controller data */
1062 static struct bfin5xx_spi_master bfin_sport_spi0_info = {
1063         .num_chipselect = 1, /* master only supports one device */
1064         .enable_dma = 0,  /* master don't support DMA */
1065         .pin_req = {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_DRPRI,
1066                 P_SPORT0_RSCLK, P_SPORT0_TFS, P_SPORT0_RFS, 0},
1067 };
1068
1069 static struct resource bfin_sport_spi0_resource[] = {
1070         [0] = {
1071                 .start = SPORT0_TCR1,
1072                 .end   = SPORT0_TCR1 + 0xFF,
1073                 .flags = IORESOURCE_MEM,
1074                 },
1075         [1] = {
1076                 .start = IRQ_SPORT0_ERROR,
1077                 .end   = IRQ_SPORT0_ERROR,
1078                 .flags = IORESOURCE_IRQ,
1079                 },
1080 };
1081
1082 static struct platform_device bfin_sport_spi0_device = {
1083         .name = "bfin-sport-spi",
1084         .id = 1, /* Bus number */
1085         .num_resources = ARRAY_SIZE(bfin_sport_spi0_resource),
1086         .resource = bfin_sport_spi0_resource,
1087         .dev = {
1088                 .platform_data = &bfin_sport_spi0_info, /* Passed to driver */
1089         },
1090 };
1091
1092 static struct bfin5xx_spi_master bfin_sport_spi1_info = {
1093         .num_chipselect = 1, /* master only supports one device */
1094         .enable_dma = 0,  /* master don't support DMA */
1095         .pin_req = {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_DRPRI,
1096                 P_SPORT1_RSCLK, P_SPORT1_TFS, P_SPORT1_RFS, 0},
1097 };
1098
1099 static struct resource bfin_sport_spi1_resource[] = {
1100         [0] = {
1101                 .start = SPORT1_TCR1,
1102                 .end   = SPORT1_TCR1 + 0xFF,
1103                 .flags = IORESOURCE_MEM,
1104                 },
1105         [1] = {
1106                 .start = IRQ_SPORT1_ERROR,
1107                 .end   = IRQ_SPORT1_ERROR,
1108                 .flags = IORESOURCE_IRQ,
1109                 },
1110 };
1111
1112 static struct platform_device bfin_sport_spi1_device = {
1113         .name = "bfin-sport-spi",
1114         .id = 2, /* Bus number */
1115         .num_resources = ARRAY_SIZE(bfin_sport_spi1_resource),
1116         .resource = bfin_sport_spi1_resource,
1117         .dev = {
1118                 .platform_data = &bfin_sport_spi1_info, /* Passed to driver */
1119         },
1120 };
1121
1122 #endif  /* sport spi master and devices */
1123
1124 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1125 static struct platform_device bfin_fb_device = {
1126         .name = "bf537-lq035",
1127 };
1128 #endif
1129
1130 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1131 #include <asm/bfin-lq035q1.h>
1132
1133 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
1134         .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
1135         .ppi_mode = USE_RGB565_16_BIT_PPI,
1136         .use_bl = 0,    /* let something else control the LCD Blacklight */
1137         .gpio_bl = GPIO_PF7,
1138 };
1139
1140 static struct resource bfin_lq035q1_resources[] = {
1141         {
1142                 .start = IRQ_PPI_ERROR,
1143                 .end = IRQ_PPI_ERROR,
1144                 .flags = IORESOURCE_IRQ,
1145         },
1146 };
1147
1148 static struct platform_device bfin_lq035q1_device = {
1149         .name           = "bfin-lq035q1",
1150         .id             = -1,
1151         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
1152         .resource       = bfin_lq035q1_resources,
1153         .dev            = {
1154                 .platform_data = &bfin_lq035q1_data,
1155         },
1156 };
1157 #endif
1158
1159 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1160 #ifdef CONFIG_SERIAL_BFIN_UART0
1161 static struct resource bfin_uart0_resources[] = {
1162         {
1163                 .start = UART0_THR,
1164                 .end = UART0_GCTL+2,
1165                 .flags = IORESOURCE_MEM,
1166         },
1167         {
1168                 .start = IRQ_UART0_RX,
1169                 .end = IRQ_UART0_RX+1,
1170                 .flags = IORESOURCE_IRQ,
1171         },
1172         {
1173                 .start = IRQ_UART0_ERROR,
1174                 .end = IRQ_UART0_ERROR,
1175                 .flags = IORESOURCE_IRQ,
1176         },
1177         {
1178                 .start = CH_UART0_TX,
1179                 .end = CH_UART0_TX,
1180                 .flags = IORESOURCE_DMA,
1181         },
1182         {
1183                 .start = CH_UART0_RX,
1184                 .end = CH_UART0_RX,
1185                 .flags = IORESOURCE_DMA,
1186         },
1187 #ifdef CONFIG_BFIN_UART0_CTSRTS
1188         {       /* CTS pin */
1189                 .start = GPIO_PG7,
1190                 .end = GPIO_PG7,
1191                 .flags = IORESOURCE_IO,
1192         },
1193         {       /* RTS pin */
1194                 .start = GPIO_PG6,
1195                 .end = GPIO_PG6,
1196                 .flags = IORESOURCE_IO,
1197         },
1198 #endif
1199 };
1200
1201 unsigned short bfin_uart0_peripherals[] = {
1202         P_UART0_TX, P_UART0_RX, 0
1203 };
1204
1205 static struct platform_device bfin_uart0_device = {
1206         .name = "bfin-uart",
1207         .id = 0,
1208         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
1209         .resource = bfin_uart0_resources,
1210         .dev = {
1211                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
1212         },
1213 };
1214 #endif
1215 #ifdef CONFIG_SERIAL_BFIN_UART1
1216 static struct resource bfin_uart1_resources[] = {
1217         {
1218                 .start = UART1_THR,
1219                 .end = UART1_GCTL+2,
1220                 .flags = IORESOURCE_MEM,
1221         },
1222         {
1223                 .start = IRQ_UART1_RX,
1224                 .end = IRQ_UART1_RX+1,
1225                 .flags = IORESOURCE_IRQ,
1226         },
1227         {
1228                 .start = IRQ_UART1_ERROR,
1229                 .end = IRQ_UART1_ERROR,
1230                 .flags = IORESOURCE_IRQ,
1231         },
1232         {
1233                 .start = CH_UART1_TX,
1234                 .end = CH_UART1_TX,
1235                 .flags = IORESOURCE_DMA,
1236         },
1237         {
1238                 .start = CH_UART1_RX,
1239                 .end = CH_UART1_RX,
1240                 .flags = IORESOURCE_DMA,
1241         },
1242 };
1243
1244 unsigned short bfin_uart1_peripherals[] = {
1245         P_UART1_TX, P_UART1_RX, 0
1246 };
1247
1248 static struct platform_device bfin_uart1_device = {
1249         .name = "bfin-uart",
1250         .id = 1,
1251         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
1252         .resource = bfin_uart1_resources,
1253         .dev = {
1254                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
1255         },
1256 };
1257 #endif
1258 #endif
1259
1260 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1261 #ifdef CONFIG_BFIN_SIR0
1262 static struct resource bfin_sir0_resources[] = {
1263         {
1264                 .start = 0xFFC00400,
1265                 .end = 0xFFC004FF,
1266                 .flags = IORESOURCE_MEM,
1267         },
1268         {
1269                 .start = IRQ_UART0_RX,
1270                 .end = IRQ_UART0_RX+1,
1271                 .flags = IORESOURCE_IRQ,
1272         },
1273         {
1274                 .start = CH_UART0_RX,
1275                 .end = CH_UART0_RX+1,
1276                 .flags = IORESOURCE_DMA,
1277         },
1278 };
1279
1280 static struct platform_device bfin_sir0_device = {
1281         .name = "bfin_sir",
1282         .id = 0,
1283         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
1284         .resource = bfin_sir0_resources,
1285 };
1286 #endif
1287 #ifdef CONFIG_BFIN_SIR1
1288 static struct resource bfin_sir1_resources[] = {
1289         {
1290                 .start = 0xFFC02000,
1291                 .end = 0xFFC020FF,
1292                 .flags = IORESOURCE_MEM,
1293         },
1294         {
1295                 .start = IRQ_UART1_RX,
1296                 .end = IRQ_UART1_RX+1,
1297                 .flags = IORESOURCE_IRQ,
1298         },
1299         {
1300                 .start = CH_UART1_RX,
1301                 .end = CH_UART1_RX+1,
1302                 .flags = IORESOURCE_DMA,
1303         },
1304 };
1305
1306 static struct platform_device bfin_sir1_device = {
1307         .name = "bfin_sir",
1308         .id = 1,
1309         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
1310         .resource = bfin_sir1_resources,
1311 };
1312 #endif
1313 #endif
1314
1315 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1316 static struct resource bfin_twi0_resource[] = {
1317         [0] = {
1318                 .start = TWI0_REGBASE,
1319                 .end   = TWI0_REGBASE,
1320                 .flags = IORESOURCE_MEM,
1321         },
1322         [1] = {
1323                 .start = IRQ_TWI,
1324                 .end   = IRQ_TWI,
1325                 .flags = IORESOURCE_IRQ,
1326         },
1327 };
1328
1329 static struct platform_device i2c_bfin_twi_device = {
1330         .name = "i2c-bfin-twi",
1331         .id = 0,
1332         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
1333         .resource = bfin_twi0_resource,
1334 };
1335 #endif
1336
1337 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
1338 #include <linux/i2c/adp5588.h>
1339 static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
1340         [0]      = KEY_GRAVE,
1341         [1]      = KEY_1,
1342         [2]      = KEY_2,
1343         [3]      = KEY_3,
1344         [4]      = KEY_4,
1345         [5]      = KEY_5,
1346         [6]      = KEY_6,
1347         [7]      = KEY_7,
1348         [8]      = KEY_8,
1349         [9]      = KEY_9,
1350         [10]     = KEY_0,
1351         [11]     = KEY_MINUS,
1352         [12]     = KEY_EQUAL,
1353         [13]     = KEY_BACKSLASH,
1354         [15]     = KEY_KP0,
1355         [16]     = KEY_Q,
1356         [17]     = KEY_W,
1357         [18]     = KEY_E,
1358         [19]     = KEY_R,
1359         [20]     = KEY_T,
1360         [21]     = KEY_Y,
1361         [22]     = KEY_U,
1362         [23]     = KEY_I,
1363         [24]     = KEY_O,
1364         [25]     = KEY_P,
1365         [26]     = KEY_LEFTBRACE,
1366         [27]     = KEY_RIGHTBRACE,
1367         [29]     = KEY_KP1,
1368         [30]     = KEY_KP2,
1369         [31]     = KEY_KP3,
1370         [32]     = KEY_A,
1371         [33]     = KEY_S,
1372         [34]     = KEY_D,
1373         [35]     = KEY_F,
1374         [36]     = KEY_G,
1375         [37]     = KEY_H,
1376         [38]     = KEY_J,
1377         [39]     = KEY_K,
1378         [40]     = KEY_L,
1379         [41]     = KEY_SEMICOLON,
1380         [42]     = KEY_APOSTROPHE,
1381         [43]     = KEY_BACKSLASH,
1382         [45]     = KEY_KP4,
1383         [46]     = KEY_KP5,
1384         [47]     = KEY_KP6,
1385         [48]     = KEY_102ND,
1386         [49]     = KEY_Z,
1387         [50]     = KEY_X,
1388         [51]     = KEY_C,
1389         [52]     = KEY_V,
1390         [53]     = KEY_B,
1391         [54]     = KEY_N,
1392         [55]     = KEY_M,
1393         [56]     = KEY_COMMA,
1394         [57]     = KEY_DOT,
1395         [58]     = KEY_SLASH,
1396         [60]     = KEY_KPDOT,
1397         [61]     = KEY_KP7,
1398         [62]     = KEY_KP8,
1399         [63]     = KEY_KP9,
1400         [64]     = KEY_SPACE,
1401         [65]     = KEY_BACKSPACE,
1402         [66]     = KEY_TAB,
1403         [67]     = KEY_KPENTER,
1404         [68]     = KEY_ENTER,
1405         [69]     = KEY_ESC,
1406         [70]     = KEY_DELETE,
1407         [74]     = KEY_KPMINUS,
1408         [76]     = KEY_UP,
1409         [77]     = KEY_DOWN,
1410         [78]     = KEY_RIGHT,
1411         [79]     = KEY_LEFT,
1412 };
1413
1414 static struct adp5588_kpad_platform_data adp5588_kpad_data = {
1415         .rows           = 8,
1416         .cols           = 10,
1417         .keymap         = adp5588_keymap,
1418         .keymapsize     = ARRAY_SIZE(adp5588_keymap),
1419         .repeat         = 0,
1420 };
1421 #endif
1422
1423 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1424 #include <linux/mfd/adp5520.h>
1425
1426         /*
1427          *  ADP5520/5501 Backlight Data
1428          */
1429
1430 static struct adp5520_backlight_platform_data adp5520_backlight_data = {
1431         .fade_in                = ADP5520_FADE_T_1200ms,
1432         .fade_out               = ADP5520_FADE_T_1200ms,
1433         .fade_led_law           = ADP5520_BL_LAW_LINEAR,
1434         .en_ambl_sens           = 1,
1435         .abml_filt              = ADP5520_BL_AMBL_FILT_640ms,
1436         .l1_daylight_max        = ADP5520_BL_CUR_mA(15),
1437         .l1_daylight_dim        = ADP5520_BL_CUR_mA(0),
1438         .l2_office_max          = ADP5520_BL_CUR_mA(7),
1439         .l2_office_dim          = ADP5520_BL_CUR_mA(0),
1440         .l3_dark_max            = ADP5520_BL_CUR_mA(3),
1441         .l3_dark_dim            = ADP5520_BL_CUR_mA(0),
1442         .l2_trip                = ADP5520_L2_COMP_CURR_uA(700),
1443         .l2_hyst                = ADP5520_L2_COMP_CURR_uA(50),
1444         .l3_trip                = ADP5520_L3_COMP_CURR_uA(80),
1445         .l3_hyst                = ADP5520_L3_COMP_CURR_uA(20),
1446 };
1447
1448         /*
1449          *  ADP5520/5501 LEDs Data
1450          */
1451
1452 static struct led_info adp5520_leds[] = {
1453         {
1454                 .name = "adp5520-led1",
1455                 .default_trigger = "none",
1456                 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
1457         },
1458 #ifdef ADP5520_EN_ALL_LEDS
1459         {
1460                 .name = "adp5520-led2",
1461                 .default_trigger = "none",
1462                 .flags = FLAG_ID_ADP5520_LED2_ADP5501_LED1,
1463         },
1464         {
1465                 .name = "adp5520-led3",
1466                 .default_trigger = "none",
1467                 .flags = FLAG_ID_ADP5520_LED3_ADP5501_LED2,
1468         },
1469 #endif
1470 };
1471
1472 static struct adp5520_leds_platform_data adp5520_leds_data = {
1473         .num_leds = ARRAY_SIZE(adp5520_leds),
1474         .leds = adp5520_leds,
1475         .fade_in = ADP5520_FADE_T_600ms,
1476         .fade_out = ADP5520_FADE_T_600ms,
1477         .led_on_time = ADP5520_LED_ONT_600ms,
1478 };
1479
1480         /*
1481          *  ADP5520 GPIO Data
1482          */
1483
1484 static struct adp5520_gpio_platform_data adp5520_gpio_data = {
1485         .gpio_start = 50,
1486         .gpio_en_mask = ADP5520_GPIO_C1 | ADP5520_GPIO_C2 | ADP5520_GPIO_R2,
1487         .gpio_pullup_mask = ADP5520_GPIO_C1 | ADP5520_GPIO_C2 | ADP5520_GPIO_R2,
1488 };
1489
1490         /*
1491          *  ADP5520 Keypad Data
1492          */
1493
1494 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
1495         [ADP5520_KEY(0, 0)]     = KEY_GRAVE,
1496         [ADP5520_KEY(0, 1)]     = KEY_1,
1497         [ADP5520_KEY(0, 2)]     = KEY_2,
1498         [ADP5520_KEY(0, 3)]     = KEY_3,
1499         [ADP5520_KEY(1, 0)]     = KEY_4,
1500         [ADP5520_KEY(1, 1)]     = KEY_5,
1501         [ADP5520_KEY(1, 2)]     = KEY_6,
1502         [ADP5520_KEY(1, 3)]     = KEY_7,
1503         [ADP5520_KEY(2, 0)]     = KEY_8,
1504         [ADP5520_KEY(2, 1)]     = KEY_9,
1505         [ADP5520_KEY(2, 2)]     = KEY_0,
1506         [ADP5520_KEY(2, 3)]     = KEY_MINUS,
1507         [ADP5520_KEY(3, 0)]     = KEY_EQUAL,
1508         [ADP5520_KEY(3, 1)]     = KEY_BACKSLASH,
1509         [ADP5520_KEY(3, 2)]     = KEY_BACKSPACE,
1510         [ADP5520_KEY(3, 3)]     = KEY_ENTER,
1511 };
1512
1513 static struct adp5520_keys_platform_data adp5520_keys_data = {
1514         .rows_en_mask   = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
1515         .cols_en_mask   = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
1516         .keymap         = adp5520_keymap,
1517         .keymapsize     = ARRAY_SIZE(adp5520_keymap),
1518         .repeat         = 0,
1519 };
1520
1521         /*
1522          *  ADP5520/5501 Multifuction Device Init Data
1523          */
1524
1525 static struct adp5520_platform_data adp5520_pdev_data = {
1526         .backlight = &adp5520_backlight_data,
1527         .leds = &adp5520_leds_data,
1528         .gpio = &adp5520_gpio_data,
1529         .keys = &adp5520_keys_data,
1530 };
1531
1532 #endif
1533
1534 #if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
1535 #include <linux/i2c/adp5588.h>
1536 static struct adp5588_gpio_platform_data adp5588_gpio_data = {
1537         .gpio_start = 50,
1538         .pullup_dis_mask = 0,
1539 };
1540 #endif
1541
1542 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
1543 #include <linux/i2c/adp8870.h>
1544 static struct led_info adp8870_leds[] = {
1545         {
1546                 .name = "adp8870-led7",
1547                 .default_trigger = "none",
1548                 .flags = ADP8870_LED_D7 | ADP8870_LED_OFFT_600ms,
1549         },
1550 };
1551
1552
1553 static struct adp8870_backlight_platform_data adp8870_pdata = {
1554         .bl_led_assign = ADP8870_BL_D1 | ADP8870_BL_D2 | ADP8870_BL_D3 |
1555                          ADP8870_BL_D4 | ADP8870_BL_D5 | ADP8870_BL_D6, /* 1 = Backlight 0 = Individual LED */
1556         .pwm_assign = 0,                                /* 1 = Enables PWM mode */
1557
1558         .bl_fade_in = ADP8870_FADE_T_1200ms,            /* Backlight Fade-In Timer */
1559         .bl_fade_out = ADP8870_FADE_T_1200ms,           /* Backlight Fade-Out Timer */
1560         .bl_fade_law = ADP8870_FADE_LAW_CUBIC1,         /* fade-on/fade-off transfer characteristic */
1561
1562         .en_ambl_sens = 1,                              /* 1 = enable ambient light sensor */
1563         .abml_filt = ADP8870_BL_AMBL_FILT_320ms,        /* Light sensor filter time */
1564
1565         .l1_daylight_max = ADP8870_BL_CUR_mA(20),       /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1566         .l1_daylight_dim = ADP8870_BL_CUR_mA(0),        /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1567         .l2_bright_max = ADP8870_BL_CUR_mA(14),         /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1568         .l2_bright_dim = ADP8870_BL_CUR_mA(0),          /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1569         .l3_office_max = ADP8870_BL_CUR_mA(6),          /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1570         .l3_office_dim = ADP8870_BL_CUR_mA(0),          /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1571         .l4_indoor_max = ADP8870_BL_CUR_mA(3),          /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1572         .l4_indor_dim = ADP8870_BL_CUR_mA(0),           /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1573         .l5_dark_max = ADP8870_BL_CUR_mA(2),            /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1574         .l5_dark_dim = ADP8870_BL_CUR_mA(0),            /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1575
1576         .l2_trip = ADP8870_L2_COMP_CURR_uA(710),        /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
1577         .l2_hyst = ADP8870_L2_COMP_CURR_uA(73),         /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
1578         .l3_trip = ADP8870_L3_COMP_CURR_uA(389),        /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
1579         .l3_hyst = ADP8870_L3_COMP_CURR_uA(54),         /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
1580         .l4_trip = ADP8870_L4_COMP_CURR_uA(167),        /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
1581         .l4_hyst = ADP8870_L4_COMP_CURR_uA(16),         /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
1582         .l5_trip = ADP8870_L5_COMP_CURR_uA(43),         /* use L5_COMP_CURR_uA(I) 0 <= I <= 138 uA */
1583         .l5_hyst = ADP8870_L5_COMP_CURR_uA(11),         /* use L6_COMP_CURR_uA(I) 0 <= I <= 138 uA */
1584
1585         .leds = adp8870_leds,
1586         .num_leds = ARRAY_SIZE(adp8870_leds),
1587         .led_fade_law = ADP8870_FADE_LAW_SQUARE,        /* fade-on/fade-off transfer characteristic */
1588         .led_fade_in = ADP8870_FADE_T_600ms,
1589         .led_fade_out = ADP8870_FADE_T_600ms,
1590         .led_on_time = ADP8870_LED_ONT_200ms,
1591 };
1592 #endif
1593
1594 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
1595 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
1596         {
1597                 I2C_BOARD_INFO("ad7142_captouch", 0x2C),
1598                 .irq = IRQ_PG5,
1599                 .platform_data = (void *)&ad7142_i2c_platform_data,
1600         },
1601 #endif
1602 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
1603         {
1604                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
1605         },
1606 #endif
1607 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
1608         {
1609                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
1610                 .irq = IRQ_PG6,
1611         },
1612 #endif
1613 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
1614         {
1615                 I2C_BOARD_INFO("ad7879", 0x2F),
1616                 .irq = IRQ_PG5,
1617                 .platform_data = (void *)&bfin_ad7879_ts_info,
1618         },
1619 #endif
1620 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
1621         {
1622                 I2C_BOARD_INFO("adp5588-keys", 0x34),
1623                 .irq = IRQ_PG0,
1624                 .platform_data = (void *)&adp5588_kpad_data,
1625         },
1626 #endif
1627 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1628         {
1629                 I2C_BOARD_INFO("pmic-adp5520", 0x32),
1630                 .irq = IRQ_PG0,
1631                 .platform_data = (void *)&adp5520_pdev_data,
1632         },
1633 #endif
1634 #if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
1635         {
1636                 I2C_BOARD_INFO("adxl34x", 0x53),
1637                 .irq = IRQ_PG3,
1638                 .platform_data = (void *)&adxl34x_info,
1639         },
1640 #endif
1641 #if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
1642         {
1643                 I2C_BOARD_INFO("adp5588-gpio", 0x34),
1644                 .platform_data = (void *)&adp5588_gpio_data,
1645         },
1646 #endif
1647 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
1648         {
1649                 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
1650         },
1651 #endif
1652 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1653         {
1654                 I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2C),
1655         },
1656 #endif
1657 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
1658         {
1659                 I2C_BOARD_INFO("adp8870", 0x2B),
1660                 .platform_data = (void *)&adp8870_pdata,
1661         },
1662 #endif
1663 #if defined(CONFIG_SND_SOC_ADAU1371) || defined(CONFIG_SND_SOC_ADAU1371_MODULE)
1664         {
1665                 I2C_BOARD_INFO("adau1371", 0x1A),
1666         },
1667 #endif
1668 #if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
1669         {
1670                 I2C_BOARD_INFO("adau1761", 0x38),
1671         },
1672 #endif
1673 #if defined(CONFIG_AD525X_DPOT) || defined(CONFIG_AD525X_DPOT_MODULE)
1674         {
1675                 I2C_BOARD_INFO("ad5258", 0x18),
1676         },
1677 #endif
1678 };
1679
1680 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1681 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1682 static struct resource bfin_sport0_uart_resources[] = {
1683         {
1684                 .start = SPORT0_TCR1,
1685                 .end = SPORT0_MRCS3+4,
1686                 .flags = IORESOURCE_MEM,
1687         },
1688         {
1689                 .start = IRQ_SPORT0_RX,
1690                 .end = IRQ_SPORT0_RX+1,
1691                 .flags = IORESOURCE_IRQ,
1692         },
1693         {
1694                 .start = IRQ_SPORT0_ERROR,
1695                 .end = IRQ_SPORT0_ERROR,
1696                 .flags = IORESOURCE_IRQ,
1697         },
1698 };
1699
1700 unsigned short bfin_sport0_peripherals[] = {
1701         P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
1702         P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
1703 };
1704
1705 static struct platform_device bfin_sport0_uart_device = {
1706         .name = "bfin-sport-uart",
1707         .id = 0,
1708         .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
1709         .resource = bfin_sport0_uart_resources,
1710         .dev = {
1711                 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
1712         },
1713 };
1714 #endif
1715 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1716 static struct resource bfin_sport1_uart_resources[] = {
1717         {
1718                 .start = SPORT1_TCR1,
1719                 .end = SPORT1_MRCS3+4,
1720                 .flags = IORESOURCE_MEM,
1721         },
1722         {
1723                 .start = IRQ_SPORT1_RX,
1724                 .end = IRQ_SPORT1_RX+1,
1725                 .flags = IORESOURCE_IRQ,
1726         },
1727         {
1728                 .start = IRQ_SPORT1_ERROR,
1729                 .end = IRQ_SPORT1_ERROR,
1730                 .flags = IORESOURCE_IRQ,
1731         },
1732 };
1733
1734 unsigned short bfin_sport1_peripherals[] = {
1735         P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
1736         P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
1737 };
1738
1739 static struct platform_device bfin_sport1_uart_device = {
1740         .name = "bfin-sport-uart",
1741         .id = 1,
1742         .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
1743         .resource = bfin_sport1_uart_resources,
1744         .dev = {
1745                 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
1746         },
1747 };
1748 #endif
1749 #endif
1750
1751 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
1752 #define CF_IDE_NAND_CARD_USE_HDD_INTERFACE
1753 /* #define CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE */
1754
1755 #ifdef CF_IDE_NAND_CARD_USE_HDD_INTERFACE
1756 #define PATA_INT        IRQ_PF5
1757 static struct pata_platform_info bfin_pata_platform_data = {
1758         .ioport_shift = 1,
1759         .irq_flags = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
1760 };
1761
1762 static struct resource bfin_pata_resources[] = {
1763         {
1764                 .start = 0x20314020,
1765                 .end = 0x2031403F,
1766                 .flags = IORESOURCE_MEM,
1767         },
1768         {
1769                 .start = 0x2031401C,
1770                 .end = 0x2031401F,
1771                 .flags = IORESOURCE_MEM,
1772         },
1773         {
1774                 .start = PATA_INT,
1775                 .end = PATA_INT,
1776                 .flags = IORESOURCE_IRQ,
1777         },
1778 };
1779 #elif defined(CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE)
1780 static struct pata_platform_info bfin_pata_platform_data = {
1781         .ioport_shift = 0,
1782 };
1783 /* CompactFlash Storage Card Memory Mapped Adressing
1784  * /REG = A11 = 1
1785  */
1786 static struct resource bfin_pata_resources[] = {
1787         {
1788                 .start = 0x20211800,
1789                 .end = 0x20211807,
1790                 .flags = IORESOURCE_MEM,
1791         },
1792         {
1793                 .start = 0x2021180E,    /* Device Ctl */
1794                 .end = 0x2021180E,
1795                 .flags = IORESOURCE_MEM,
1796         },
1797 };
1798 #endif
1799
1800 static struct platform_device bfin_pata_device = {
1801         .name = "pata_platform",
1802         .id = -1,
1803         .num_resources = ARRAY_SIZE(bfin_pata_resources),
1804         .resource = bfin_pata_resources,
1805         .dev = {
1806                 .platform_data = &bfin_pata_platform_data,
1807         }
1808 };
1809 #endif
1810
1811 static const unsigned int cclk_vlev_datasheet[] =
1812 {
1813         VRPAIR(VLEV_085, 250000000),
1814         VRPAIR(VLEV_090, 376000000),
1815         VRPAIR(VLEV_095, 426000000),
1816         VRPAIR(VLEV_100, 426000000),
1817         VRPAIR(VLEV_105, 476000000),
1818         VRPAIR(VLEV_110, 476000000),
1819         VRPAIR(VLEV_115, 476000000),
1820         VRPAIR(VLEV_120, 500000000),
1821         VRPAIR(VLEV_125, 533000000),
1822         VRPAIR(VLEV_130, 600000000),
1823 };
1824
1825 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
1826         .tuple_tab = cclk_vlev_datasheet,
1827         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
1828         .vr_settling_time = 25 /* us */,
1829 };
1830
1831 static struct platform_device bfin_dpmc = {
1832         .name = "bfin dpmc",
1833         .dev = {
1834                 .platform_data = &bfin_dmpc_vreg_data,
1835         },
1836 };
1837
1838 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1839 static struct platform_device bfin_tdm = {
1840         .name = "bfin-tdm",
1841         /* TODO: add platform data here */
1842 };
1843 #endif
1844
1845 static struct platform_device *stamp_devices[] __initdata = {
1846
1847         &bfin_dpmc,
1848
1849 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
1850         &bfin_pcmcia_cf_device,
1851 #endif
1852
1853 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
1854         &rtc_device,
1855 #endif
1856
1857 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
1858         &sl811_hcd_device,
1859 #endif
1860
1861 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
1862         &isp1362_hcd_device,
1863 #endif
1864
1865 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
1866         &bfin_isp1760_device,
1867 #endif
1868
1869 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
1870         &smc91x_device,
1871 #endif
1872
1873 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
1874         &dm9000_device,
1875 #endif
1876
1877 #if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
1878         &bfin_can_device,
1879 #endif
1880
1881 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
1882         &bfin_mii_bus,
1883         &bfin_mac_device,
1884 #endif
1885
1886 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
1887         &net2272_bfin_device,
1888 #endif
1889
1890 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1891         &bfin_spi0_device,
1892 #endif
1893
1894 #if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
1895         &bfin_sport_spi0_device,
1896         &bfin_sport_spi1_device,
1897 #endif
1898
1899 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1900         &bfin_fb_device,
1901 #endif
1902
1903 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1904         &bfin_lq035q1_device,
1905 #endif
1906
1907 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1908 #ifdef CONFIG_SERIAL_BFIN_UART0
1909         &bfin_uart0_device,
1910 #endif
1911 #ifdef CONFIG_SERIAL_BFIN_UART1
1912         &bfin_uart1_device,
1913 #endif
1914 #endif
1915
1916 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1917 #ifdef CONFIG_BFIN_SIR0
1918         &bfin_sir0_device,
1919 #endif
1920 #ifdef CONFIG_BFIN_SIR1
1921         &bfin_sir1_device,
1922 #endif
1923 #endif
1924
1925 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1926         &i2c_bfin_twi_device,
1927 #endif
1928
1929 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1930 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1931         &bfin_sport0_uart_device,
1932 #endif
1933 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1934         &bfin_sport1_uart_device,
1935 #endif
1936 #endif
1937
1938 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
1939         &bfin_pata_device,
1940 #endif
1941
1942 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1943         &bfin_device_gpiokeys,
1944 #endif
1945
1946 #if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
1947         &bfin_async_nand_device,
1948 #endif
1949
1950 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1951         &stamp_flash_device,
1952 #endif
1953
1954 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1955         &bfin_tdm,
1956 #endif
1957 };
1958
1959 static int __init stamp_init(void)
1960 {
1961         printk(KERN_INFO "%s(): registering device resources\n", __func__);
1962         bfin_plat_nand_init();
1963         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
1964         i2c_register_board_info(0, bfin_i2c_board_info,
1965                                 ARRAY_SIZE(bfin_i2c_board_info));
1966         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
1967
1968         return 0;
1969 }
1970
1971 arch_initcall(stamp_init);
1972
1973
1974 static struct platform_device *stamp_early_devices[] __initdata = {
1975 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1976 #ifdef CONFIG_SERIAL_BFIN_UART0
1977         &bfin_uart0_device,
1978 #endif
1979 #ifdef CONFIG_SERIAL_BFIN_UART1
1980         &bfin_uart1_device,
1981 #endif
1982 #endif
1983
1984 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
1985 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1986         &bfin_sport0_uart_device,
1987 #endif
1988 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1989         &bfin_sport1_uart_device,
1990 #endif
1991 #endif
1992 };
1993
1994 void __init native_machine_early_platform_add_devices(void)
1995 {
1996         printk(KERN_INFO "register early platform devices\n");
1997         early_platform_add_devices(stamp_early_devices,
1998                 ARRAY_SIZE(stamp_early_devices));
1999 }
2000
2001 void native_machine_restart(char *cmd)
2002 {
2003         /* workaround reboot hang when booting from SPI */
2004         if ((bfin_read_SYSCR() & 0x7) == 0x3)
2005                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
2006 }
2007
2008 /*
2009  * Currently the MAC address is saved in Flash by U-Boot
2010  */
2011 #define FLASH_MAC       0x203f0000
2012 void bfin_get_ether_addr(char *addr)
2013 {
2014         *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
2015         *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
2016 }
2017 EXPORT_SYMBOL(bfin_get_ether_addr);