arch/blackfin/mach-bf537/boards/stamp.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2 or later.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/kernel.h>
  11 #include <linux/platform_device.h>
  12 #include <linux/io.h>
  13 #include <linux/mtd/mtd.h>
  14 #include <linux/mtd/nand.h>
  15 #include <linux/mtd/partitions.h>
  16 #include <linux/mtd/plat-ram.h>
  17 #include <linux/mtd/physmap.h>
  18 #include <linux/spi/spi.h>
  19 #include <linux/spi/flash.h>
  20 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
  21 #include <linux/usb/isp1362.h>
  22 #endif
  23 #include <linux/i2c.h>
  24 #include <linux/i2c/adp5588.h>
  25 #include <linux/etherdevice.h>
  26 #include <linux/ata_platform.h>
  27 #include <linux/irq.h>
  28 #include <linux/interrupt.h>
  29 #include <linux/usb/sl811.h>
  30 #include <linux/spi/mmc_spi.h>
  31 #include <linux/leds.h>
  32 #include <linux/input.h>
  33 #include <asm/dma.h>
  34 #include <asm/bfin5xx_spi.h>
  35 #include <asm/reboot.h>
  36 #include <asm/portmux.h>
  37 #include <asm/dpmc.h>
  38 #ifdef CONFIG_REGULATOR_ADP_SWITCH
  39 #include <linux/regulator/adp_switch.h>
  40 #endif
  41 #ifdef CONFIG_REGULATOR_AD5398
  42 #include <linux/regulator/ad5398.h>
  43 #endif
  44 #include <linux/regulator/consumer.h>
  45 #include <linux/regulator/userspace-consumer.h>
  46
  47 /*
  48  * Name the Board for the /proc/cpuinfo
  49  */
  50 const char bfin_board_name[] = "ADI BF537-STAMP";
  51
  52 /*
  53  *  Driver needs to know address, irq and flag pin.
  54  */
  55
  56 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  57 #include <linux/usb/isp1760.h>
  58 static struct resource bfin_isp1760_resources[] = {
  59         [0] = {
  60                 .start  = 0x203C0000,
  61                 .end    = 0x203C0000 + 0x000fffff,
  62                 .flags  = IORESOURCE_MEM,
  63         },
  64         [1] = {
  65                 .start  = IRQ_PF7,
  66                 .end    = IRQ_PF7,
  67                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
  68         },
  69 };
  70
  71 static struct isp1760_platform_data isp1760_priv = {
  72         .is_isp1761 = 0,
  73         .bus_width_16 = 1,
  74         .port1_otg = 0,
  75         .analog_oc = 0,
  76         .dack_polarity_high = 0,
  77         .dreq_polarity_high = 0,
  78 };
  79
  80 static struct platform_device bfin_isp1760_device = {
  81         .name           = "isp1760",
  82         .id             = 0,
  83         .dev = {
  84                 .platform_data = &isp1760_priv,
  85         },
  86         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  87         .resource       = bfin_isp1760_resources,
  88 };
  89 #endif
  90
  91 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
  92 #include <linux/gpio_keys.h>
  93
  94 static struct gpio_keys_button bfin_gpio_keys_table[] = {
  95         {BTN_0, GPIO_PF2, 1, "gpio-keys: BTN0"},
  96         {BTN_1, GPIO_PF3, 1, "gpio-keys: BTN1"},
  97         {BTN_2, GPIO_PF4, 1, "gpio-keys: BTN2"},
  98         {BTN_3, GPIO_PF5, 1, "gpio-keys: BTN3"},
  99 };
 100
 101 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
 102         .buttons        = bfin_gpio_keys_table,
 103         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
 104 };
 105
 106 static struct platform_device bfin_device_gpiokeys = {
 107         .name      = "gpio-keys",
 108         .dev = {
 109                 .platform_data = &bfin_gpio_keys_data,
 110         },
 111 };
 112 #endif
 113
 114 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 115 static struct resource bfin_pcmcia_cf_resources[] = {
 116         {
 117                 .start = 0x20310000, /* IO PORT */
 118                 .end = 0x20312000,
 119                 .flags = IORESOURCE_MEM,
 120         }, {
 121                 .start = 0x20311000, /* Attribute Memory */
 122                 .end = 0x20311FFF,
 123                 .flags = IORESOURCE_MEM,
 124         }, {
 125                 .start = IRQ_PF4,
 126                 .end = IRQ_PF4,
 127                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 128         }, {
 129                 .start = 6, /* Card Detect PF6 */
 130                 .end = 6,
 131                 .flags = IORESOURCE_IRQ,
 132         },
 133 };
 134
 135 static struct platform_device bfin_pcmcia_cf_device = {
 136         .name = "bfin_cf_pcmcia",
 137         .id = -1,
 138         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 139         .resource = bfin_pcmcia_cf_resources,
 140 };
 141 #endif
 142
 143 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 144 static struct platform_device rtc_device = {
 145         .name = "rtc-bfin",
 146         .id   = -1,
 147 };
 148 #endif
 149
 150 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 151 #include <linux/smc91x.h>
 152
 153 static struct smc91x_platdata smc91x_info = {
 154         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 155         .leda = RPC_LED_100_10,
 156         .ledb = RPC_LED_TX_RX,
 157 };
 158
 159 static struct resource smc91x_resources[] = {
 160         {
 161                 .name = "smc91x-regs",
 162                 .start = 0x20300300,
 163                 .end = 0x20300300 + 16,
 164                 .flags = IORESOURCE_MEM,
 165         }, {
 166
 167                 .start = IRQ_PF7,
 168                 .end = IRQ_PF7,
 169                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 170         },
 171 };
 172 static struct platform_device smc91x_device = {
 173         .name = "smc91x",
 174         .id = 0,
 175         .num_resources = ARRAY_SIZE(smc91x_resources),
 176         .resource = smc91x_resources,
 177         .dev    = {
 178                 .platform_data  = &smc91x_info,
 179         },
 180 };
 181 #endif
 182
 183 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 184 static struct resource dm9000_resources[] = {
 185         [0] = {
 186                 .start  = 0x203FB800,
 187                 .end    = 0x203FB800 + 1,
 188                 .flags  = IORESOURCE_MEM,
 189         },
 190         [1] = {
 191                 .start  = 0x203FB804,
 192                 .end    = 0x203FB804 + 1,
 193                 .flags  = IORESOURCE_MEM,
 194         },
 195         [2] = {
 196                 .start  = IRQ_PF9,
 197                 .end    = IRQ_PF9,
 198                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 199         },
 200 };
 201
 202 static struct platform_device dm9000_device = {
 203         .name           = "dm9000",
 204         .id             = -1,
 205         .num_resources  = ARRAY_SIZE(dm9000_resources),
 206         .resource       = dm9000_resources,
 207 };
 208 #endif
 209
 210 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
 211 static struct resource sl811_hcd_resources[] = {
 212         {
 213                 .start = 0x20340000,
 214                 .end = 0x20340000,
 215                 .flags = IORESOURCE_MEM,
 216         }, {
 217                 .start = 0x20340004,
 218                 .end = 0x20340004,
 219                 .flags = IORESOURCE_MEM,
 220         }, {
 221                 .start = IRQ_PF4,
 222                 .end = IRQ_PF4,
 223                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 224         },
 225 };
 226
 227 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 228 void sl811_port_power(struct device *dev, int is_on)
 229 {
 230         gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
 231         gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
 232 }
 233 #endif
 234
 235 static struct sl811_platform_data sl811_priv = {
 236         .potpg = 10,
 237         .power = 250,       /* == 500mA */
 238 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 239         .port_power = &sl811_port_power,
 240 #endif
 241 };
 242
 243 static struct platform_device sl811_hcd_device = {
 244         .name = "sl811-hcd",
 245         .id = 0,
 246         .dev = {
 247                 .platform_data = &sl811_priv,
 248         },
 249         .num_resources = ARRAY_SIZE(sl811_hcd_resources),
 250         .resource = sl811_hcd_resources,
 251 };
 252 #endif
 253
 254 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 255 static struct resource isp1362_hcd_resources[] = {
 256         {
 257                 .start = 0x20360000,
 258                 .end = 0x20360000,
 259                 .flags = IORESOURCE_MEM,
 260         }, {
 261                 .start = 0x20360004,
 262                 .end = 0x20360004,
 263                 .flags = IORESOURCE_MEM,
 264         }, {
 265                 .start = IRQ_PF3,
 266                 .end = IRQ_PF3,
 267                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 268         },
 269 };
 270
 271 static struct isp1362_platform_data isp1362_priv = {
 272         .sel15Kres = 1,
 273         .clknotstop = 0,
 274         .oc_enable = 0,
 275         .int_act_high = 0,
 276         .int_edge_triggered = 0,
 277         .remote_wakeup_connected = 0,
 278         .no_power_switching = 1,
 279         .power_switching_mode = 0,
 280 };
 281
 282 static struct platform_device isp1362_hcd_device = {
 283         .name = "isp1362-hcd",
 284         .id = 0,
 285         .dev = {
 286                 .platform_data = &isp1362_priv,
 287         },
 288         .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 289         .resource = isp1362_hcd_resources,
 290 };
 291 #endif
 292
 293 #if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
 294 unsigned short bfin_can_peripherals[] = {
 295         P_CAN0_RX, P_CAN0_TX, 0
 296 };
 297
 298 static struct resource bfin_can_resources[] = {
 299         {
 300                 .start = 0xFFC02A00,
 301                 .end = 0xFFC02FFF,
 302                 .flags = IORESOURCE_MEM,
 303         },
 304         {
 305                 .start = IRQ_CAN_RX,
 306                 .end = IRQ_CAN_RX,
 307                 .flags = IORESOURCE_IRQ,
 308         },
 309         {
 310                 .start = IRQ_CAN_TX,
 311                 .end = IRQ_CAN_TX,
 312                 .flags = IORESOURCE_IRQ,
 313         },
 314         {
 315                 .start = IRQ_CAN_ERROR,
 316                 .end = IRQ_CAN_ERROR,
 317                 .flags = IORESOURCE_IRQ,
 318         },
 319 };
 320
 321 static struct platform_device bfin_can_device = {
 322         .name = "bfin_can",
 323         .num_resources = ARRAY_SIZE(bfin_can_resources),
 324         .resource = bfin_can_resources,
 325         .dev = {
 326                 .platform_data = &bfin_can_peripherals, /* Passed to driver */
 327         },
 328 };
 329 #endif
 330
 331 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 332 static struct platform_device bfin_mii_bus = {
 333         .name = "bfin_mii_bus",
 334 };
 335
 336 static struct platform_device bfin_mac_device = {
 337         .name = "bfin_mac",
 338         .dev.platform_data = &bfin_mii_bus,
 339 };
 340 #endif
 341
 342 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 343 static struct resource net2272_bfin_resources[] = {
 344         {
 345                 .start = 0x20300000,
 346                 .end = 0x20300000 + 0x100,
 347                 .flags = IORESOURCE_MEM,
 348         }, {
 349                 .start = IRQ_PF7,
 350                 .end = IRQ_PF7,
 351                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 352         },
 353 };
 354
 355 static struct platform_device net2272_bfin_device = {
 356         .name = "net2272",
 357         .id = -1,
 358         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 359         .resource = net2272_bfin_resources,
 360 };
 361 #endif
 362
 363 #if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 364 #ifdef CONFIG_MTD_PARTITIONS
 365 const char *part_probes[] = { "cmdlinepart", "RedBoot", NULL };
 366
 367 static struct mtd_partition bfin_plat_nand_partitions[] = {
 368         {
 369                 .name   = "linux kernel(nand)",
 370                 .size   = 0x400000,
 371                 .offset = 0,
 372         }, {
 373                 .name   = "file system(nand)",
 374                 .size   = MTDPART_SIZ_FULL,
 375                 .offset = MTDPART_OFS_APPEND,
 376         },
 377 };
 378 #endif
 379
 380 #define BFIN_NAND_PLAT_CLE 2
 381 #define BFIN_NAND_PLAT_ALE 1
 382 static void bfin_plat_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
 383 {
 384         struct nand_chip *this = mtd->priv;
 385
 386         if (cmd == NAND_CMD_NONE)
 387                 return;
 388
 389         if (ctrl & NAND_CLE)
 390                 writeb(cmd, this->IO_ADDR_W + (1 << BFIN_NAND_PLAT_CLE));
 391         else
 392                 writeb(cmd, this->IO_ADDR_W + (1 << BFIN_NAND_PLAT_ALE));
 393 }
 394
 395 #define BFIN_NAND_PLAT_READY GPIO_PF3
 396 static int bfin_plat_nand_dev_ready(struct mtd_info *mtd)
 397 {
 398         return gpio_get_value(BFIN_NAND_PLAT_READY);
 399 }
 400
 401 static struct platform_nand_data bfin_plat_nand_data = {
 402         .chip = {
 403                 .chip_delay = 30,
 404 #ifdef CONFIG_MTD_PARTITIONS
 405                 .part_probe_types = part_probes,
 406                 .partitions = bfin_plat_nand_partitions,
 407                 .nr_partitions = ARRAY_SIZE(bfin_plat_nand_partitions),
 408 #endif
 409         },
 410         .ctrl = {
 411                 .cmd_ctrl  = bfin_plat_nand_cmd_ctrl,
 412                 .dev_ready = bfin_plat_nand_dev_ready,
 413         },
 414 };
 415
 416 #define MAX(x, y) (x > y ? x : y)
 417 static struct resource bfin_plat_nand_resources = {
 418         .start = 0x20212000,
 419         .end   = 0x20212000 + (1 << MAX(BFIN_NAND_PLAT_CLE, BFIN_NAND_PLAT_ALE)),
 420         .flags = IORESOURCE_IO,
 421 };
 422
 423 static struct platform_device bfin_async_nand_device = {
 424         .name = "gen_nand",
 425         .id = -1,
 426         .num_resources = 1,
 427         .resource = &bfin_plat_nand_resources,
 428         .dev = {
 429                 .platform_data = &bfin_plat_nand_data,
 430         },
 431 };
 432
 433 static void bfin_plat_nand_init(void)
 434 {
 435         gpio_request(BFIN_NAND_PLAT_READY, "bfin_nand_plat");
 436 }
 437 #else
 438 static void bfin_plat_nand_init(void) {}
 439 #endif
 440
 441 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 442 static struct mtd_partition stamp_partitions[] = {
 443         {
 444                 .name       = "bootloader(nor)",
 445                 .size       = 0x40000,
 446                 .offset     = 0,
 447         }, {
 448                 .name       = "linux kernel(nor)",
 449                 .size       = 0x180000,
 450                 .offset     = MTDPART_OFS_APPEND,
 451         }, {
 452                 .name       = "file system(nor)",
 453                 .size       = 0x400000 - 0x40000 - 0x180000 - 0x10000,
 454                 .offset     = MTDPART_OFS_APPEND,
 455         }, {
 456                 .name       = "MAC Address(nor)",
 457                 .size       = MTDPART_SIZ_FULL,
 458                 .offset     = 0x3F0000,
 459                 .mask_flags = MTD_WRITEABLE,
 460         }
 461 };
 462
 463 static struct physmap_flash_data stamp_flash_data = {
 464         .width      = 2,
 465         .parts      = stamp_partitions,
 466         .nr_parts   = ARRAY_SIZE(stamp_partitions),
 467 #ifdef CONFIG_ROMKERNEL
 468         .probe_type = "map_rom",
 469 #endif
 470 };
 471
 472 static struct resource stamp_flash_resource = {
 473         .start = 0x20000000,
 474         .end   = 0x203fffff,
 475         .flags = IORESOURCE_MEM,
 476 };
 477
 478 static struct platform_device stamp_flash_device = {
 479         .name          = "physmap-flash",
 480         .id            = 0,
 481         .dev = {
 482                 .platform_data = &stamp_flash_data,
 483         },
 484         .num_resources = 1,
 485         .resource      = &stamp_flash_resource,
 486 };
 487 #endif
 488
 489 #if defined(CONFIG_MTD_M25P80) \
 490         || defined(CONFIG_MTD_M25P80_MODULE)
 491 static struct mtd_partition bfin_spi_flash_partitions[] = {
 492         {
 493                 .name = "bootloader(spi)",
 494                 .size = 0x00040000,
 495                 .offset = 0,
 496                 .mask_flags = MTD_CAP_ROM
 497         }, {
 498                 .name = "linux kernel(spi)",
 499                 .size = 0x180000,
 500                 .offset = MTDPART_OFS_APPEND,
 501         }, {
 502                 .name = "file system(spi)",
 503                 .size = MTDPART_SIZ_FULL,
 504                 .offset = MTDPART_OFS_APPEND,
 505         }
 506 };
 507
 508 static struct flash_platform_data bfin_spi_flash_data = {
 509         .name = "m25p80",
 510         .parts = bfin_spi_flash_partitions,
 511         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 512         /* .type = "m25p64", */
 513 };
 514
 515 /* SPI flash chip (m25p64) */
 516 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 517         .enable_dma = 0,         /* use dma transfer with this chip*/
 518         .bits_per_word = 8,
 519 };
 520 #endif
 521
 522 #if defined(CONFIG_BFIN_SPI_ADC) \
 523         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 524 /* SPI ADC chip */
 525 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 526         .enable_dma = 1,         /* use dma transfer with this chip*/
 527         .bits_per_word = 16,
 528 };
 529 #endif
 530
 531 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 532         || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 533 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 534         .enable_dma = 0,
 535         .bits_per_word = 16,
 536 };
 537 #endif
 538
 539 #if defined(CONFIG_SND_BF5XX_SOC_AD193X) \
 540         || defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
 541 static struct bfin5xx_spi_chip ad1938_spi_chip_info = {
 542         .enable_dma = 0,
 543         .bits_per_word = 8,
 544 };
 545 #endif
 546
 547 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 548 #include <linux/input/ad714x.h>
 549 static struct bfin5xx_spi_chip ad7147_spi_chip_info = {
 550         .enable_dma = 0,
 551         .bits_per_word = 16,
 552 };
 553
 554 static struct ad714x_slider_plat ad7147_spi_slider_plat[] = {
 555         {
 556                 .start_stage = 0,
 557                 .end_stage = 7,
 558                 .max_coord = 128,
 559         },
 560 };
 561
 562 static struct ad714x_button_plat ad7147_spi_button_plat[] = {
 563         {
 564                 .keycode = BTN_FORWARD,
 565                 .l_mask = 0,
 566                 .h_mask = 0x600,
 567         },
 568         {
 569                 .keycode = BTN_LEFT,
 570                 .l_mask = 0,
 571                 .h_mask = 0x500,
 572         },
 573         {
 574                 .keycode = BTN_MIDDLE,
 575                 .l_mask = 0,
 576                 .h_mask = 0x800,
 577         },
 578         {
 579                 .keycode = BTN_RIGHT,
 580                 .l_mask = 0x100,
 581                 .h_mask = 0x400,
 582         },
 583         {
 584                 .keycode = BTN_BACK,
 585                 .l_mask = 0x200,
 586                 .h_mask = 0x400,
 587         },
 588 };
 589 static struct ad714x_platform_data ad7147_spi_platform_data = {
 590         .slider_num = 1,
 591         .button_num = 5,
 592         .slider = ad7147_spi_slider_plat,
 593         .button = ad7147_spi_button_plat,
 594         .stage_cfg_reg =  {
 595                 {0xFBFF, 0x1FFF, 0, 0x2626, 1600, 1600, 1600, 1600},
 596                 {0xEFFF, 0x1FFF, 0, 0x2626, 1650, 1650, 1650, 1650},
 597                 {0xFFFF, 0x1FFE, 0, 0x2626, 1650, 1650, 1650, 1650},
 598                 {0xFFFF, 0x1FFB, 0, 0x2626, 1650, 1650, 1650, 1650},
 599                 {0xFFFF, 0x1FEF, 0, 0x2626, 1650, 1650, 1650, 1650},
 600                 {0xFFFF, 0x1FBF, 0, 0x2626, 1650, 1650, 1650, 1650},
 601                 {0xFFFF, 0x1EFF, 0, 0x2626, 1650, 1650, 1650, 1650},
 602                 {0xFFFF, 0x1BFF, 0, 0x2626, 1600, 1600, 1600, 1600},
 603                 {0xFF7B, 0x3FFF, 0x506,  0x2626, 1100, 1100, 1150, 1150},
 604                 {0xFDFE, 0x3FFF, 0x606,  0x2626, 1100, 1100, 1150, 1150},
 605                 {0xFEBA, 0x1FFF, 0x1400, 0x2626, 1200, 1200, 1300, 1300},
 606                 {0xFFEF, 0x1FFF, 0x0,    0x2626, 1100, 1100, 1150, 1150},
 607         },
 608         .sys_cfg_reg = {0x2B2, 0x0, 0x3233, 0x819, 0x832, 0xCFF, 0xCFF, 0x0},
 609 };
 610 #endif
 611
 612 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
 613 #include <linux/input/ad714x.h>
 614 static struct ad714x_button_plat ad7142_i2c_button_plat[] = {
 615         {
 616                 .keycode = BTN_1,
 617                 .l_mask = 0,
 618                 .h_mask = 0x1,
 619         },
 620         {
 621                 .keycode = BTN_2,
 622                 .l_mask = 0,
 623                 .h_mask = 0x2,
 624         },
 625         {
 626                 .keycode = BTN_3,
 627                 .l_mask = 0,
 628                 .h_mask = 0x4,
 629         },
 630         {
 631                 .keycode = BTN_4,
 632                 .l_mask = 0x0,
 633                 .h_mask = 0x8,
 634         },
 635 };
 636 static struct ad714x_platform_data ad7142_i2c_platform_data = {
 637         .button_num = 4,
 638         .button = ad7142_i2c_button_plat,
 639         .stage_cfg_reg =  {
 640                 /* fixme: figure out right setting for all comoponent according
 641                  * to hardware feature of EVAL-AD7142EB board */
 642                 {0xE7FF, 0x3FFF, 0x0005, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 643                 {0xFDBF, 0x3FFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 644                 {0xFFFF, 0x2DFF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 645                 {0xFFFF, 0x37BF, 0x0001, 0x2626, 0x01F4, 0x01F4, 0x028A, 0x028A},
 646                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 647                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 648                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 649                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 650                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 651                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 652                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 653                 {0xFFFF, 0x3FFF, 0x0000, 0x0606, 0x01F4, 0x01F4, 0x0320, 0x0320},
 654         },
 655         .sys_cfg_reg = {0x0B2, 0x0, 0x690, 0x664, 0x290F, 0xF, 0xF, 0x0},
 656 };
 657 #endif
 658
 659 #if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
 660 static struct bfin5xx_spi_chip ad2s90_spi_chip_info = {
 661         .enable_dma = 0,
 662         .bits_per_word = 16,
 663 };
 664 #endif
 665
 666 #if defined(CONFIG_AD2S120X) || defined(CONFIG_AD2S120X_MODULE)
 667 unsigned short ad2s120x_platform_data[] = {
 668         /* used as SAMPLE and RDVEL */
 669         GPIO_PF5, GPIO_PF6, 0
 670 };
 671
 672 static struct bfin5xx_spi_chip ad2s120x_spi_chip_info = {
 673         .enable_dma = 0,
 674         .bits_per_word = 16,
 675 };
 676 #endif
 677
 678 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 679 #define MMC_SPI_CARD_DETECT_INT IRQ_PF5
 680
 681 static int bfin_mmc_spi_init(struct device *dev,
 682         irqreturn_t (*detect_int)(int, void *), void *data)
 683 {
 684         return request_irq(MMC_SPI_CARD_DETECT_INT, detect_int,
 685                 IRQF_TRIGGER_FALLING, "mmc-spi-detect", data);
 686 }
 687
 688 static void bfin_mmc_spi_exit(struct device *dev, void *data)
 689 {
 690         free_irq(MMC_SPI_CARD_DETECT_INT, data);
 691 }
 692
 693 static struct mmc_spi_platform_data bfin_mmc_spi_pdata = {
 694         .init = bfin_mmc_spi_init,
 695         .exit = bfin_mmc_spi_exit,
 696         .detect_delay = 100, /* msecs */
 697 };
 698
 699 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 700         .enable_dma = 0,
 701         .bits_per_word = 8,
 702         .pio_interrupt = 0,
 703 };
 704 #endif
 705
 706 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 707 #include <linux/spi/ad7877.h>
 708 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 709         .enable_dma = 0,
 710         .bits_per_word = 16,
 711 };
 712
 713 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 714         .model                  = 7877,
 715         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 716         .x_plate_ohms           = 419,
 717         .y_plate_ohms           = 486,
 718         .pressure_max           = 1000,
 719         .pressure_min           = 0,
 720         .stopacq_polarity       = 1,
 721         .first_conversion_delay = 3,
 722         .acquisition_time       = 1,
 723         .averaging              = 1,
 724         .pen_down_acc_interval  = 1,
 725 };
 726 #endif
 727
 728 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 729 #include <linux/spi/ad7879.h>
 730 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 731         .model                  = 7879, /* Model = AD7879 */
 732         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 733         .pressure_max           = 10000,
 734         .pressure_min           = 0,
 735         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 736         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 737         .median                 = 2,    /* do 8 measurements */
 738         .averaging              = 1,    /* take the average of 4 middle samples */
 739         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 740         .gpio_export            = 1,    /* Export GPIO to gpiolib */
 741         .gpio_base              = -1,   /* Dynamic allocation */
 742 };
 743 #endif
 744
 745 #if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
 746 #include <linux/input/adxl34x.h>
 747 static const struct adxl34x_platform_data adxl34x_info = {
 748         .x_axis_offset = 0,
 749         .y_axis_offset = 0,
 750         .z_axis_offset = 0,
 751         .tap_threshold = 0x31,
 752         .tap_duration = 0x10,
 753         .tap_latency = 0x60,
 754         .tap_window = 0xF0,
 755         .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
 756         .act_axis_control = 0xFF,
 757         .activity_threshold = 5,
 758         .inactivity_threshold = 3,
 759         .inactivity_time = 4,
 760         .free_fall_threshold = 0x7,
 761         .free_fall_time = 0x20,
 762         .data_rate = 0x8,
 763         .data_range = ADXL_FULL_RES,
 764
 765         .ev_type = EV_ABS,
 766         .ev_code_x = ABS_X,             /* EV_REL */
 767         .ev_code_y = ABS_Y,             /* EV_REL */
 768         .ev_code_z = ABS_Z,             /* EV_REL */
 769
 770         .ev_code_tap = {BTN_TOUCH, BTN_TOUCH, BTN_TOUCH}, /* EV_KEY x,y,z */
 771
 772 /*      .ev_code_ff = KEY_F,*/          /* EV_KEY */
 773 /*      .ev_code_act_inactivity = KEY_A,*/      /* EV_KEY */
 774         .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
 775         .fifo_mode = ADXL_FIFO_STREAM,
 776 };
 777 #endif
 778
 779 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 780 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 781         .enable_dma = 0,
 782         .bits_per_word = 16,
 783 };
 784 #endif
 785
 786 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 787 static struct bfin5xx_spi_chip spidev_chip_info = {
 788         .enable_dma = 0,
 789         .bits_per_word = 8,
 790 };
 791 #endif
 792
 793 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 794 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 795         .enable_dma     = 0,
 796         .bits_per_word  = 8,
 797 };
 798 #endif
 799
 800 #if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
 801 static struct bfin5xx_spi_chip enc28j60_spi_chip_info = {
 802         .enable_dma     = 1,
 803         .bits_per_word  = 8,
 804         .cs_gpio = GPIO_PF10,
 805 };
 806 #endif
 807
 808 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
 809 static struct bfin5xx_spi_chip adf7021_spi_chip_info = {
 810         .bits_per_word = 16,
 811         .cs_gpio = GPIO_PF10,
 812 };
 813
 814 #include <linux/spi/adf702x.h>
 815 #define TXREG 0x0160A470
 816 static const u32 adf7021_regs[] = {
 817         0x09608FA0,
 818         0x00575011,
 819         0x00A7F092,
 820         0x2B141563,
 821         0x81F29E94,
 822         0x00003155,
 823         0x050A4F66,
 824         0x00000007,
 825         0x00000008,
 826         0x000231E9,
 827         0x3296354A,
 828         0x891A2B3B,
 829         0x00000D9C,
 830         0x0000000D,
 831         0x0000000E,
 832         0x0000000F,
 833 };
 834
 835 static struct adf702x_platform_data adf7021_platform_data = {
 836         .regs_base = (void *)SPORT1_TCR1,
 837         .dma_ch_rx = CH_SPORT1_RX,
 838         .dma_ch_tx = CH_SPORT1_TX,
 839         .irq_sport_err = IRQ_SPORT1_ERROR,
 840         .gpio_int_rfs = GPIO_PF8,
 841         .pin_req = {P_SPORT1_DTPRI, P_SPORT1_RFS, P_SPORT1_DRPRI,
 842                         P_SPORT1_RSCLK, P_SPORT1_TSCLK, 0},
 843         .adf702x_model = MODEL_ADF7021,
 844         .adf702x_regs = adf7021_regs,
 845         .tx_reg = TXREG,
 846 };
 847 static inline void adf702x_mac_init(void)
 848 {
 849         random_ether_addr(adf7021_platform_data.mac_addr);
 850 }
 851 #else
 852 static inline void adf702x_mac_init(void) {}
 853 #endif
 854
 855 #if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
 856 #include <linux/spi/ads7846.h>
 857 static struct bfin5xx_spi_chip ad7873_spi_chip_info = {
 858         .bits_per_word  = 8,
 859 };
 860
 861 static int ads7873_get_pendown_state(void)
 862 {
 863         return gpio_get_value(GPIO_PF6);
 864 }
 865
 866 static struct ads7846_platform_data __initdata ad7873_pdata = {
 867         .model          = 7873,         /* AD7873 */
 868         .x_max          = 0xfff,
 869         .y_max          = 0xfff,
 870         .x_plate_ohms   = 620,
 871         .debounce_max   = 1,
 872         .debounce_rep   = 0,
 873         .debounce_tol   = (~0),
 874         .get_pendown_state = ads7873_get_pendown_state,
 875 };
 876 #endif
 877
 878 #if defined(CONFIG_MTD_DATAFLASH) \
 879         || defined(CONFIG_MTD_DATAFLASH_MODULE)
 880
 881 static struct mtd_partition bfin_spi_dataflash_partitions[] = {
 882         {
 883                 .name = "bootloader(spi)",
 884                 .size = 0x00040000,
 885                 .offset = 0,
 886                 .mask_flags = MTD_CAP_ROM
 887         }, {
 888                 .name = "linux kernel(spi)",
 889                 .size = 0x180000,
 890                 .offset = MTDPART_OFS_APPEND,
 891         }, {
 892                 .name = "file system(spi)",
 893                 .size = MTDPART_SIZ_FULL,
 894                 .offset = MTDPART_OFS_APPEND,
 895         }
 896 };
 897
 898 static struct flash_platform_data bfin_spi_dataflash_data = {
 899         .name = "SPI Dataflash",
 900         .parts = bfin_spi_dataflash_partitions,
 901         .nr_parts = ARRAY_SIZE(bfin_spi_dataflash_partitions),
 902 };
 903
 904 /* DataFlash chip */
 905 static struct bfin5xx_spi_chip data_flash_chip_info = {
 906         .enable_dma = 0,         /* use dma transfer with this chip*/
 907         .bits_per_word = 8,
 908 };
 909 #endif
 910
 911 #if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
 912 static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
 913         .enable_dma = 0,         /* use dma transfer with this chip*/
 914         .bits_per_word = 8,
 915 };
 916 #endif
 917
 918 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 919 #if defined(CONFIG_MTD_M25P80) \
 920         || defined(CONFIG_MTD_M25P80_MODULE)
 921         {
 922                 /* the modalias must be the same as spi device driver name */
 923                 .modalias = "m25p80", /* Name of spi_driver for this device */
 924                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 925                 .bus_num = 0, /* Framework bus number */
 926                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 927                 .platform_data = &bfin_spi_flash_data,
 928                 .controller_data = &spi_flash_chip_info,
 929                 .mode = SPI_MODE_3,
 930         },
 931 #endif
 932 #if defined(CONFIG_MTD_DATAFLASH) \
 933         || defined(CONFIG_MTD_DATAFLASH_MODULE)
 934         {       /* DataFlash chip */
 935                 .modalias = "mtd_dataflash",
 936                 .max_speed_hz = 33250000,     /* max spi clock (SCK) speed in HZ */
 937                 .bus_num = 0, /* Framework bus number */
 938                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 939                 .platform_data = &bfin_spi_dataflash_data,
 940                 .controller_data = &data_flash_chip_info,
 941                 .mode = SPI_MODE_3,
 942         },
 943 #endif
 944 #if defined(CONFIG_BFIN_SPI_ADC) \
 945         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 946         {
 947                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 948                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 949                 .bus_num = 0, /* Framework bus number */
 950                 .chip_select = 1, /* Framework chip select. */
 951                 .platform_data = NULL, /* No spi_driver specific config */
 952                 .controller_data = &spi_adc_chip_info,
 953         },
 954 #endif
 955
 956 #if defined(CONFIG_SND_BF5XX_SOC_AD1836) \
 957         || defined(CONFIG_SND_BF5XX_SOC_AD1836_MODULE)
 958         {
 959                 .modalias = "ad1836",
 960                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 961                 .bus_num = 0,
 962                 .chip_select = 4,/* CONFIG_SND_BLACKFIN_SPI_PFBIT */
 963                 .controller_data = &ad1836_spi_chip_info,
 964                 .mode = SPI_MODE_3,
 965         },
 966 #endif
 967
 968 #if defined(CONFIG_SND_BF5XX_SOC_AD193X) || defined(CONFIG_SND_BF5XX_SOC_AD193X_MODULE)
 969         {
 970                 .modalias = "ad193x",
 971                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 972                 .bus_num = 0,
 973                 .chip_select = 5,
 974                 .controller_data = &ad1938_spi_chip_info,
 975                 .mode = SPI_MODE_3,
 976         },
 977 #endif
 978
 979 #if defined(CONFIG_INPUT_AD714X_SPI) || defined(CONFIG_INPUT_AD714X_SPI_MODULE)
 980         {
 981                 .modalias = "ad714x_captouch",
 982                 .max_speed_hz = 1000000,     /* max spi clock (SCK) speed in HZ */
 983                 .irq = IRQ_PF4,
 984                 .bus_num = 0,
 985                 .chip_select = 5,
 986                 .mode = SPI_MODE_3,
 987                 .platform_data = &ad7147_spi_platform_data,
 988                 .controller_data = &ad7147_spi_chip_info,
 989         },
 990 #endif
 991
 992 #if defined(CONFIG_AD2S90) || defined(CONFIG_AD2S90_MODULE)
 993         {
 994                 .modalias = "ad2s90",
 995                 .bus_num = 0,
 996                 .chip_select = 3,            /* change it for your board */
 997                 .platform_data = NULL,
 998                 .controller_data = &ad2s90_spi_chip_info,
 999         },
1000 #endif
1001
1002 #if defined(CONFIG_AD2S120X) || defined(CONFIG_AD2S120X_MODULE)
1003         {
1004                 .modalias = "ad2s120x",
1005                 .bus_num = 0,
1006                 .chip_select = 4,            /* CS, change it for your board */
1007                 .platform_data = ad2s120x_platform_data,
1008                 .controller_data = &ad2s120x_spi_chip_info,
1009         },
1010 #endif
1011
1012 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
1013         {
1014                 .modalias = "mmc_spi",
1015                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
1016                 .bus_num = 0,
1017                 .chip_select = 4,
1018                 .platform_data = &bfin_mmc_spi_pdata,
1019                 .controller_data = &mmc_spi_chip_info,
1020                 .mode = SPI_MODE_3,
1021         },
1022 #endif
1023 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
1024         {
1025                 .modalias               = "ad7877",
1026                 .platform_data          = &bfin_ad7877_ts_info,
1027                 .irq                    = IRQ_PF6,
1028                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
1029                 .bus_num        = 0,
1030                 .chip_select  = 1,
1031                 .controller_data = &spi_ad7877_chip_info,
1032         },
1033 #endif
1034 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
1035         {
1036                 .modalias = "ad7879",
1037                 .platform_data = &bfin_ad7879_ts_info,
1038                 .irq = IRQ_PF7,
1039                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
1040                 .bus_num = 0,
1041                 .chip_select = 1,
1042                 .controller_data = &spi_ad7879_chip_info,
1043                 .mode = SPI_CPHA | SPI_CPOL,
1044         },
1045 #endif
1046 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
1047         {
1048                 .modalias = "spidev",
1049                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
1050                 .bus_num = 0,
1051                 .chip_select = 1,
1052                 .controller_data = &spidev_chip_info,
1053         },
1054 #endif
1055 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1056         {
1057                 .modalias = "bfin-lq035q1-spi",
1058                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
1059                 .bus_num = 0,
1060                 .chip_select = 2,
1061                 .controller_data = &lq035q1_spi_chip_info,
1062                 .mode = SPI_CPHA | SPI_CPOL,
1063         },
1064 #endif
1065 #if defined(CONFIG_ENC28J60) || defined(CONFIG_ENC28J60_MODULE)
1066         {
1067                 .modalias = "enc28j60",
1068                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
1069                 .irq = IRQ_PF6,
1070                 .bus_num = 0,
1071                 .chip_select = 0,       /* GPIO controlled SSEL */
1072                 .controller_data = &enc28j60_spi_chip_info,
1073                 .mode = SPI_MODE_0,
1074         },
1075 #endif
1076 #if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
1077         {
1078                 .modalias       = "adxl34x",
1079                 .platform_data  = &adxl34x_info,
1080                 .irq            = IRQ_PF6,
1081                 .max_speed_hz   = 5000000,    /* max spi clock (SCK) speed in HZ */
1082                 .bus_num        = 0,
1083                 .chip_select    = 2,
1084                 .controller_data = &spi_adxl34x_chip_info,
1085                 .mode = SPI_MODE_3,
1086         },
1087 #endif
1088 #if defined(CONFIG_ADF702X) || defined(CONFIG_ADF702X_MODULE)
1089         {
1090                 .modalias = "adf702x",
1091                 .max_speed_hz = 16000000,     /* max spi clock (SCK) speed in HZ */
1092                 .bus_num = 0,
1093                 .chip_select = 0,       /* GPIO controlled SSEL */
1094                 .controller_data = &adf7021_spi_chip_info,
1095                 .platform_data = &adf7021_platform_data,
1096                 .mode = SPI_MODE_0,
1097         },
1098 #endif
1099 #if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
1100         {
1101                 .modalias = "ads7846",
1102                 .max_speed_hz = 2000000,     /* max spi clock (SCK) speed in HZ */
1103                 .bus_num = 0,
1104                 .irq = IRQ_PF6,
1105                 .chip_select = GPIO_PF10 + MAX_CTRL_CS, /* GPIO controlled SSEL */
1106                 .controller_data = &ad7873_spi_chip_info,
1107                 .platform_data = &ad7873_pdata,
1108                 .mode = SPI_MODE_0,
1109         },
1110 #endif
1111 };
1112
1113 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1114 /* SPI controller data */
1115 static struct bfin5xx_spi_master bfin_spi0_info = {
1116         .num_chipselect = 8,
1117         .enable_dma = 1,  /* master has the ability to do dma transfer */
1118         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
1119 };
1120
1121 /* SPI (0) */
1122 static struct resource bfin_spi0_resource[] = {
1123         [0] = {
1124                 .start = SPI0_REGBASE,
1125                 .end   = SPI0_REGBASE + 0xFF,
1126                 .flags = IORESOURCE_MEM,
1127                 },
1128         [1] = {
1129                 .start = CH_SPI,
1130                 .end   = CH_SPI,
1131                 .flags = IORESOURCE_DMA,
1132         },
1133         [2] = {
1134                 .start = IRQ_SPI,
1135                 .end   = IRQ_SPI,
1136                 .flags = IORESOURCE_IRQ,
1137         },
1138 };
1139
1140 static struct platform_device bfin_spi0_device = {
1141         .name = "bfin-spi",
1142         .id = 0, /* Bus number */
1143         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
1144         .resource = bfin_spi0_resource,
1145         .dev = {
1146                 .platform_data = &bfin_spi0_info, /* Passed to driver */
1147         },
1148 };
1149 #endif  /* spi master and devices */
1150
1151 #if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
1152
1153 /* SPORT SPI controller data */
1154 static struct bfin5xx_spi_master bfin_sport_spi0_info = {
1155         .num_chipselect = 1, /* master only supports one device */
1156         .enable_dma = 0,  /* master don't support DMA */
1157         .pin_req = {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_DRPRI,
1158                 P_SPORT0_RSCLK, P_SPORT0_TFS, P_SPORT0_RFS, 0},
1159 };
1160
1161 static struct resource bfin_sport_spi0_resource[] = {
1162         [0] = {
1163                 .start = SPORT0_TCR1,
1164                 .end   = SPORT0_TCR1 + 0xFF,
1165                 .flags = IORESOURCE_MEM,
1166                 },
1167         [1] = {
1168                 .start = IRQ_SPORT0_ERROR,
1169                 .end   = IRQ_SPORT0_ERROR,
1170                 .flags = IORESOURCE_IRQ,
1171                 },
1172 };
1173
1174 static struct platform_device bfin_sport_spi0_device = {
1175         .name = "bfin-sport-spi",
1176         .id = 1, /* Bus number */
1177         .num_resources = ARRAY_SIZE(bfin_sport_spi0_resource),
1178         .resource = bfin_sport_spi0_resource,
1179         .dev = {
1180                 .platform_data = &bfin_sport_spi0_info, /* Passed to driver */
1181         },
1182 };
1183
1184 static struct bfin5xx_spi_master bfin_sport_spi1_info = {
1185         .num_chipselect = 1, /* master only supports one device */
1186         .enable_dma = 0,  /* master don't support DMA */
1187         .pin_req = {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_DRPRI,
1188                 P_SPORT1_RSCLK, P_SPORT1_TFS, P_SPORT1_RFS, 0},
1189 };
1190
1191 static struct resource bfin_sport_spi1_resource[] = {
1192         [0] = {
1193                 .start = SPORT1_TCR1,
1194                 .end   = SPORT1_TCR1 + 0xFF,
1195                 .flags = IORESOURCE_MEM,
1196                 },
1197         [1] = {
1198                 .start = IRQ_SPORT1_ERROR,
1199                 .end   = IRQ_SPORT1_ERROR,
1200                 .flags = IORESOURCE_IRQ,
1201                 },
1202 };
1203
1204 static struct platform_device bfin_sport_spi1_device = {
1205         .name = "bfin-sport-spi",
1206         .id = 2, /* Bus number */
1207         .num_resources = ARRAY_SIZE(bfin_sport_spi1_resource),
1208         .resource = bfin_sport_spi1_resource,
1209         .dev = {
1210                 .platform_data = &bfin_sport_spi1_info, /* Passed to driver */
1211         },
1212 };
1213
1214 #endif  /* sport spi master and devices */
1215
1216 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1217 static struct platform_device bfin_fb_device = {
1218         .name = "bf537-lq035",
1219 };
1220 #endif
1221
1222 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1223 #include <asm/bfin-lq035q1.h>
1224
1225 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
1226         .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
1227         .ppi_mode = USE_RGB565_16_BIT_PPI,
1228         .use_bl = 0,    /* let something else control the LCD Blacklight */
1229         .gpio_bl = GPIO_PF7,
1230 };
1231
1232 static struct resource bfin_lq035q1_resources[] = {
1233         {
1234                 .start = IRQ_PPI_ERROR,
1235                 .end = IRQ_PPI_ERROR,
1236                 .flags = IORESOURCE_IRQ,
1237         },
1238 };
1239
1240 static struct platform_device bfin_lq035q1_device = {
1241         .name           = "bfin-lq035q1",
1242         .id             = -1,
1243         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
1244         .resource       = bfin_lq035q1_resources,
1245         .dev            = {
1246                 .platform_data = &bfin_lq035q1_data,
1247         },
1248 };
1249 #endif
1250
1251 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1252 #ifdef CONFIG_SERIAL_BFIN_UART0
1253 static struct resource bfin_uart0_resources[] = {
1254         {
1255                 .start = UART0_THR,
1256                 .end = UART0_GCTL+2,
1257                 .flags = IORESOURCE_MEM,
1258         },
1259         {
1260                 .start = IRQ_UART0_RX,
1261                 .end = IRQ_UART0_RX+1,
1262                 .flags = IORESOURCE_IRQ,
1263         },
1264         {
1265                 .start = IRQ_UART0_ERROR,
1266                 .end = IRQ_UART0_ERROR,
1267                 .flags = IORESOURCE_IRQ,
1268         },
1269         {
1270                 .start = CH_UART0_TX,
1271                 .end = CH_UART0_TX,
1272                 .flags = IORESOURCE_DMA,
1273         },
1274         {
1275                 .start = CH_UART0_RX,
1276                 .end = CH_UART0_RX,
1277                 .flags = IORESOURCE_DMA,
1278         },
1279 #ifdef CONFIG_BFIN_UART0_CTSRTS
1280         {       /* CTS pin */
1281                 .start = GPIO_PG7,
1282                 .end = GPIO_PG7,
1283                 .flags = IORESOURCE_IO,
1284         },
1285         {       /* RTS pin */
1286                 .start = GPIO_PG6,
1287                 .end = GPIO_PG6,
1288                 .flags = IORESOURCE_IO,
1289         },
1290 #endif
1291 };
1292
1293 unsigned short bfin_uart0_peripherals[] = {
1294         P_UART0_TX, P_UART0_RX, 0
1295 };
1296
1297 static struct platform_device bfin_uart0_device = {
1298         .name = "bfin-uart",
1299         .id = 0,
1300         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
1301         .resource = bfin_uart0_resources,
1302         .dev = {
1303                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
1304         },
1305 };
1306 #endif
1307 #ifdef CONFIG_SERIAL_BFIN_UART1
1308 static struct resource bfin_uart1_resources[] = {
1309         {
1310                 .start = UART1_THR,
1311                 .end = UART1_GCTL+2,
1312                 .flags = IORESOURCE_MEM,
1313         },
1314         {
1315                 .start = IRQ_UART1_RX,
1316                 .end = IRQ_UART1_RX+1,
1317                 .flags = IORESOURCE_IRQ,
1318         },
1319         {
1320                 .start = IRQ_UART1_ERROR,
1321                 .end = IRQ_UART1_ERROR,
1322                 .flags = IORESOURCE_IRQ,
1323         },
1324         {
1325                 .start = CH_UART1_TX,
1326                 .end = CH_UART1_TX,
1327                 .flags = IORESOURCE_DMA,
1328         },
1329         {
1330                 .start = CH_UART1_RX,
1331                 .end = CH_UART1_RX,
1332                 .flags = IORESOURCE_DMA,
1333         },
1334 };
1335
1336 unsigned short bfin_uart1_peripherals[] = {
1337         P_UART1_TX, P_UART1_RX, 0
1338 };
1339
1340 static struct platform_device bfin_uart1_device = {
1341         .name = "bfin-uart",
1342         .id = 1,
1343         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
1344         .resource = bfin_uart1_resources,
1345         .dev = {
1346                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
1347         },
1348 };
1349 #endif
1350 #endif
1351
1352 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1353 #ifdef CONFIG_BFIN_SIR0
1354 static struct resource bfin_sir0_resources[] = {
1355         {
1356                 .start = 0xFFC00400,
1357                 .end = 0xFFC004FF,
1358                 .flags = IORESOURCE_MEM,
1359         },
1360         {
1361                 .start = IRQ_UART0_RX,
1362                 .end = IRQ_UART0_RX+1,
1363                 .flags = IORESOURCE_IRQ,
1364         },
1365         {
1366                 .start = CH_UART0_RX,
1367                 .end = CH_UART0_RX+1,
1368                 .flags = IORESOURCE_DMA,
1369         },
1370 };
1371
1372 static struct platform_device bfin_sir0_device = {
1373         .name = "bfin_sir",
1374         .id = 0,
1375         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
1376         .resource = bfin_sir0_resources,
1377 };
1378 #endif
1379 #ifdef CONFIG_BFIN_SIR1
1380 static struct resource bfin_sir1_resources[] = {
1381         {
1382                 .start = 0xFFC02000,
1383                 .end = 0xFFC020FF,
1384                 .flags = IORESOURCE_MEM,
1385         },
1386         {
1387                 .start = IRQ_UART1_RX,
1388                 .end = IRQ_UART1_RX+1,
1389                 .flags = IORESOURCE_IRQ,
1390         },
1391         {
1392                 .start = CH_UART1_RX,
1393                 .end = CH_UART1_RX+1,
1394                 .flags = IORESOURCE_DMA,
1395         },
1396 };
1397
1398 static struct platform_device bfin_sir1_device = {
1399         .name = "bfin_sir",
1400         .id = 1,
1401         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
1402         .resource = bfin_sir1_resources,
1403 };
1404 #endif
1405 #endif
1406
1407 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1408 static struct resource bfin_twi0_resource[] = {
1409         [0] = {
1410                 .start = TWI0_REGBASE,
1411                 .end   = TWI0_REGBASE,
1412                 .flags = IORESOURCE_MEM,
1413         },
1414         [1] = {
1415                 .start = IRQ_TWI,
1416                 .end   = IRQ_TWI,
1417                 .flags = IORESOURCE_IRQ,
1418         },
1419 };
1420
1421 static struct platform_device i2c_bfin_twi_device = {
1422         .name = "i2c-bfin-twi",
1423         .id = 0,
1424         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
1425         .resource = bfin_twi0_resource,
1426 };
1427 #endif
1428
1429 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
1430 static const unsigned short adp5588_keymap[ADP5588_KEYMAPSIZE] = {
1431         [0]      = KEY_GRAVE,
1432         [1]      = KEY_1,
1433         [2]      = KEY_2,
1434         [3]      = KEY_3,
1435         [4]      = KEY_4,
1436         [5]      = KEY_5,
1437         [6]      = KEY_6,
1438         [7]      = KEY_7,
1439         [8]      = KEY_8,
1440         [9]      = KEY_9,
1441         [10]     = KEY_0,
1442         [11]     = KEY_MINUS,
1443         [12]     = KEY_EQUAL,
1444         [13]     = KEY_BACKSLASH,
1445         [15]     = KEY_KP0,
1446         [16]     = KEY_Q,
1447         [17]     = KEY_W,
1448         [18]     = KEY_E,
1449         [19]     = KEY_R,
1450         [20]     = KEY_T,
1451         [21]     = KEY_Y,
1452         [22]     = KEY_U,
1453         [23]     = KEY_I,
1454         [24]     = KEY_O,
1455         [25]     = KEY_P,
1456         [26]     = KEY_LEFTBRACE,
1457         [27]     = KEY_RIGHTBRACE,
1458         [29]     = KEY_KP1,
1459         [30]     = KEY_KP2,
1460         [31]     = KEY_KP3,
1461         [32]     = KEY_A,
1462         [33]     = KEY_S,
1463         [34]     = KEY_D,
1464         [35]     = KEY_F,
1465         [36]     = KEY_G,
1466         [37]     = KEY_H,
1467         [38]     = KEY_J,
1468         [39]     = KEY_K,
1469         [40]     = KEY_L,
1470         [41]     = KEY_SEMICOLON,
1471         [42]     = KEY_APOSTROPHE,
1472         [43]     = KEY_BACKSLASH,
1473         [45]     = KEY_KP4,
1474         [46]     = KEY_KP5,
1475         [47]     = KEY_KP6,
1476         [48]     = KEY_102ND,
1477         [49]     = KEY_Z,
1478         [50]     = KEY_X,
1479         [51]     = KEY_C,
1480         [52]     = KEY_V,
1481         [53]     = KEY_B,
1482         [54]     = KEY_N,
1483         [55]     = KEY_M,
1484         [56]     = KEY_COMMA,
1485         [57]     = KEY_DOT,
1486         [58]     = KEY_SLASH,
1487         [60]     = KEY_KPDOT,
1488         [61]     = KEY_KP7,
1489         [62]     = KEY_KP8,
1490         [63]     = KEY_KP9,
1491         [64]     = KEY_SPACE,
1492         [65]     = KEY_BACKSPACE,
1493         [66]     = KEY_TAB,
1494         [67]     = KEY_KPENTER,
1495         [68]     = KEY_ENTER,
1496         [69]     = KEY_ESC,
1497         [70]     = KEY_DELETE,
1498         [74]     = KEY_KPMINUS,
1499         [76]     = KEY_UP,
1500         [77]     = KEY_DOWN,
1501         [78]     = KEY_RIGHT,
1502         [79]     = KEY_LEFT,
1503 };
1504
1505 static struct adp5588_kpad_platform_data adp5588_kpad_data = {
1506         .rows           = 8,
1507         .cols           = 10,
1508         .keymap         = adp5588_keymap,
1509         .keymapsize     = ARRAY_SIZE(adp5588_keymap),
1510         .repeat         = 0,
1511 };
1512 #endif
1513
1514 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1515 #include <linux/mfd/adp5520.h>
1516
1517         /*
1518          *  ADP5520/5501 Backlight Data
1519          */
1520
1521 static struct adp5520_backlight_platform_data adp5520_backlight_data = {
1522         .fade_in                = ADP5520_FADE_T_1200ms,
1523         .fade_out               = ADP5520_FADE_T_1200ms,
1524         .fade_led_law           = ADP5520_BL_LAW_LINEAR,
1525         .en_ambl_sens           = 1,
1526         .abml_filt              = ADP5520_BL_AMBL_FILT_640ms,
1527         .l1_daylight_max        = ADP5520_BL_CUR_mA(15),
1528         .l1_daylight_dim        = ADP5520_BL_CUR_mA(0),
1529         .l2_office_max          = ADP5520_BL_CUR_mA(7),
1530         .l2_office_dim          = ADP5520_BL_CUR_mA(0),
1531         .l3_dark_max            = ADP5520_BL_CUR_mA(3),
1532         .l3_dark_dim            = ADP5520_BL_CUR_mA(0),
1533         .l2_trip                = ADP5520_L2_COMP_CURR_uA(700),
1534         .l2_hyst                = ADP5520_L2_COMP_CURR_uA(50),
1535         .l3_trip                = ADP5520_L3_COMP_CURR_uA(80),
1536         .l3_hyst                = ADP5520_L3_COMP_CURR_uA(20),
1537 };
1538
1539         /*
1540          *  ADP5520/5501 LEDs Data
1541          */
1542
1543 static struct led_info adp5520_leds[] = {
1544         {
1545                 .name = "adp5520-led1",
1546                 .default_trigger = "none",
1547                 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
1548         },
1549 #ifdef ADP5520_EN_ALL_LEDS
1550         {
1551                 .name = "adp5520-led2",
1552                 .default_trigger = "none",
1553                 .flags = FLAG_ID_ADP5520_LED2_ADP5501_LED1,
1554         },
1555         {
1556                 .name = "adp5520-led3",
1557                 .default_trigger = "none",
1558                 .flags = FLAG_ID_ADP5520_LED3_ADP5501_LED2,
1559         },
1560 #endif
1561 };
1562
1563 static struct adp5520_leds_platform_data adp5520_leds_data = {
1564         .num_leds = ARRAY_SIZE(adp5520_leds),
1565         .leds = adp5520_leds,
1566         .fade_in = ADP5520_FADE_T_600ms,
1567         .fade_out = ADP5520_FADE_T_600ms,
1568         .led_on_time = ADP5520_LED_ONT_600ms,
1569 };
1570
1571         /*
1572          *  ADP5520 GPIO Data
1573          */
1574
1575 static struct adp5520_gpio_platform_data adp5520_gpio_data = {
1576         .gpio_start = 50,
1577         .gpio_en_mask = ADP5520_GPIO_C1 | ADP5520_GPIO_C2 | ADP5520_GPIO_R2,
1578         .gpio_pullup_mask = ADP5520_GPIO_C1 | ADP5520_GPIO_C2 | ADP5520_GPIO_R2,
1579 };
1580
1581         /*
1582          *  ADP5520 Keypad Data
1583          */
1584
1585 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
1586         [ADP5520_KEY(0, 0)]     = KEY_GRAVE,
1587         [ADP5520_KEY(0, 1)]     = KEY_1,
1588         [ADP5520_KEY(0, 2)]     = KEY_2,
1589         [ADP5520_KEY(0, 3)]     = KEY_3,
1590         [ADP5520_KEY(1, 0)]     = KEY_4,
1591         [ADP5520_KEY(1, 1)]     = KEY_5,
1592         [ADP5520_KEY(1, 2)]     = KEY_6,
1593         [ADP5520_KEY(1, 3)]     = KEY_7,
1594         [ADP5520_KEY(2, 0)]     = KEY_8,
1595         [ADP5520_KEY(2, 1)]     = KEY_9,
1596         [ADP5520_KEY(2, 2)]     = KEY_0,
1597         [ADP5520_KEY(2, 3)]     = KEY_MINUS,
1598         [ADP5520_KEY(3, 0)]     = KEY_EQUAL,
1599         [ADP5520_KEY(3, 1)]     = KEY_BACKSLASH,
1600         [ADP5520_KEY(3, 2)]     = KEY_BACKSPACE,
1601         [ADP5520_KEY(3, 3)]     = KEY_ENTER,
1602 };
1603
1604 static struct adp5520_keys_platform_data adp5520_keys_data = {
1605         .rows_en_mask   = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
1606         .cols_en_mask   = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
1607         .keymap         = adp5520_keymap,
1608         .keymapsize     = ARRAY_SIZE(adp5520_keymap),
1609         .repeat         = 0,
1610 };
1611
1612         /*
1613          *  ADP5520/5501 Multifuction Device Init Data
1614          */
1615
1616 static struct adp5520_platform_data adp5520_pdev_data = {
1617         .backlight = &adp5520_backlight_data,
1618         .leds = &adp5520_leds_data,
1619         .gpio = &adp5520_gpio_data,
1620         .keys = &adp5520_keys_data,
1621 };
1622
1623 #endif
1624
1625 #if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
1626 static struct adp5588_gpio_platform_data adp5588_gpio_data = {
1627         .gpio_start = 50,
1628         .pullup_dis_mask = 0,
1629 };
1630 #endif
1631
1632 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
1633 #include <linux/i2c/adp8870.h>
1634 static struct led_info adp8870_leds[] = {
1635         {
1636                 .name = "adp8870-led7",
1637                 .default_trigger = "none",
1638                 .flags = ADP8870_LED_D7 | ADP8870_LED_OFFT_600ms,
1639         },
1640 };
1641
1642
1643 static struct adp8870_backlight_platform_data adp8870_pdata = {
1644         .bl_led_assign = ADP8870_BL_D1 | ADP8870_BL_D2 | ADP8870_BL_D3 |
1645                          ADP8870_BL_D4 | ADP8870_BL_D5 | ADP8870_BL_D6, /* 1 = Backlight 0 = Individual LED */
1646         .pwm_assign = 0,                                /* 1 = Enables PWM mode */
1647
1648         .bl_fade_in = ADP8870_FADE_T_1200ms,            /* Backlight Fade-In Timer */
1649         .bl_fade_out = ADP8870_FADE_T_1200ms,           /* Backlight Fade-Out Timer */
1650         .bl_fade_law = ADP8870_FADE_LAW_CUBIC1,         /* fade-on/fade-off transfer characteristic */
1651
1652         .en_ambl_sens = 1,                              /* 1 = enable ambient light sensor */
1653         .abml_filt = ADP8870_BL_AMBL_FILT_320ms,        /* Light sensor filter time */
1654
1655         .l1_daylight_max = ADP8870_BL_CUR_mA(20),       /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1656         .l1_daylight_dim = ADP8870_BL_CUR_mA(0),        /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1657         .l2_bright_max = ADP8870_BL_CUR_mA(14),         /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1658         .l2_bright_dim = ADP8870_BL_CUR_mA(0),          /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1659         .l3_office_max = ADP8870_BL_CUR_mA(6),          /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1660         .l3_office_dim = ADP8870_BL_CUR_mA(0),          /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1661         .l4_indoor_max = ADP8870_BL_CUR_mA(3),          /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1662         .l4_indor_dim = ADP8870_BL_CUR_mA(0),           /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1663         .l5_dark_max = ADP8870_BL_CUR_mA(2),            /* use BL_CUR_mA(I) 0 <= I <= 30 mA */
1664         .l5_dark_dim = ADP8870_BL_CUR_mA(0),            /* typ = 0, use BL_CUR_mA(I) 0 <= I <= 30 mA */
1665
1666         .l2_trip = ADP8870_L2_COMP_CURR_uA(710),        /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
1667         .l2_hyst = ADP8870_L2_COMP_CURR_uA(73),         /* use L2_COMP_CURR_uA(I) 0 <= I <= 1106 uA */
1668         .l3_trip = ADP8870_L3_COMP_CURR_uA(389),        /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
1669         .l3_hyst = ADP8870_L3_COMP_CURR_uA(54),         /* use L3_COMP_CURR_uA(I) 0 <= I <= 551 uA */
1670         .l4_trip = ADP8870_L4_COMP_CURR_uA(167),        /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
1671         .l4_hyst = ADP8870_L4_COMP_CURR_uA(16),         /* use L4_COMP_CURR_uA(I) 0 <= I <= 275 uA */
1672         .l5_trip = ADP8870_L5_COMP_CURR_uA(43),         /* use L5_COMP_CURR_uA(I) 0 <= I <= 138 uA */
1673         .l5_hyst = ADP8870_L5_COMP_CURR_uA(11),         /* use L6_COMP_CURR_uA(I) 0 <= I <= 138 uA */
1674
1675         .leds = adp8870_leds,
1676         .num_leds = ARRAY_SIZE(adp8870_leds),
1677         .led_fade_law = ADP8870_FADE_LAW_SQUARE,        /* fade-on/fade-off transfer characteristic */
1678         .led_fade_in = ADP8870_FADE_T_600ms,
1679         .led_fade_out = ADP8870_FADE_T_600ms,
1680         .led_on_time = ADP8870_LED_ONT_200ms,
1681 };
1682 #endif
1683
1684 #if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
1685 static struct regulator_consumer_supply ad5398_consumer = {
1686         .supply = "current",
1687 };
1688
1689 static struct regulator_init_data ad5398_regulator_data = {
1690         .constraints = {
1691                 .name = "current range",
1692                 .max_uA = 120000,
1693                 .valid_ops_mask = REGULATOR_CHANGE_CURRENT | REGULATOR_CHANGE_STATUS,
1694         },
1695         .num_consumer_supplies = 1,
1696         .consumer_supplies     = &ad5398_consumer,
1697 };
1698
1699 static struct ad5398_platform_data ad5398_i2c_platform_data = {
1700         .current_bits = 10,
1701         .current_offset = 4,
1702         .regulator_data = &ad5398_regulator_data,
1703 };
1704
1705 #if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
1706         defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
1707 static struct platform_device ad5398_virt_consumer_device = {
1708         .name = "reg-virt-consumer",
1709         .id = 0,
1710         .dev = {
1711                 .platform_data = "current", /* Passed to driver */
1712         },
1713 };
1714 #endif
1715 #if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
1716         defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
1717 static struct regulator_bulk_data ad5398_bulk_data = {
1718         .supply = "current",
1719 };
1720
1721 static struct regulator_userspace_consumer_data ad5398_userspace_comsumer_data = {
1722         .name = "ad5398",
1723         .num_supplies = 1,
1724         .supplies = &ad5398_bulk_data,
1725 };
1726
1727 static struct platform_device ad5398_userspace_consumer_device = {
1728         .name = "reg-userspace-consumer",
1729         .id = 0,
1730         .dev = {
1731                 .platform_data = &ad5398_userspace_comsumer_data,
1732         },
1733 };
1734 #endif
1735 #endif
1736
1737 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
1738 #if defined(CONFIG_INPUT_AD714X_I2C) || defined(CONFIG_INPUT_AD714X_I2C_MODULE)
1739         {
1740                 I2C_BOARD_INFO("ad7142_captouch", 0x2C),
1741                 .irq = IRQ_PG5,
1742                 .platform_data = (void *)&ad7142_i2c_platform_data,
1743         },
1744 #endif
1745
1746 #if defined(CONFIG_AD7150) || defined(CONFIG_AD7150_MODULE)
1747         {
1748                 I2C_BOARD_INFO("ad7150", 0x48),
1749                 .irq = IRQ_PG5, /* fixme: use real interrupt number */
1750         },
1751 #endif
1752
1753 #if defined(CONFIG_AD7152) || defined(CONFIG_AD7152_MODULE)
1754         {
1755                 I2C_BOARD_INFO("ad7152", 0x48),
1756         },
1757 #endif
1758
1759 #if defined(CONFIG_AD774X) || defined(CONFIG_AD774X_MODULE)
1760         {
1761                 I2C_BOARD_INFO("ad774x", 0x48),
1762         },
1763 #endif
1764
1765 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
1766         {
1767                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
1768         },
1769 #endif
1770 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
1771         {
1772                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
1773                 .irq = IRQ_PG6,
1774         },
1775 #endif
1776 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
1777         {
1778                 I2C_BOARD_INFO("ad7879", 0x2F),
1779                 .irq = IRQ_PG5,
1780                 .platform_data = (void *)&bfin_ad7879_ts_info,
1781         },
1782 #endif
1783 #if defined(CONFIG_KEYBOARD_ADP5588) || defined(CONFIG_KEYBOARD_ADP5588_MODULE)
1784         {
1785                 I2C_BOARD_INFO("adp5588-keys", 0x34),
1786                 .irq = IRQ_PG0,
1787                 .platform_data = (void *)&adp5588_kpad_data,
1788         },
1789 #endif
1790 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1791         {
1792                 I2C_BOARD_INFO("pmic-adp5520", 0x32),
1793                 .irq = IRQ_PG0,
1794                 .platform_data = (void *)&adp5520_pdev_data,
1795         },
1796 #endif
1797 #if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
1798         {
1799                 I2C_BOARD_INFO("adxl34x", 0x53),
1800                 .irq = IRQ_PG3,
1801                 .platform_data = (void *)&adxl34x_info,
1802         },
1803 #endif
1804 #if defined(CONFIG_GPIO_ADP5588) || defined(CONFIG_GPIO_ADP5588_MODULE)
1805         {
1806                 I2C_BOARD_INFO("adp5588-gpio", 0x34),
1807                 .platform_data = (void *)&adp5588_gpio_data,
1808         },
1809 #endif
1810 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
1811         {
1812                 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
1813         },
1814 #endif
1815 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
1816         {
1817                 I2C_BOARD_INFO("bf537-lq035-ad5280", 0x2C),
1818         },
1819 #endif
1820 #if defined(CONFIG_BACKLIGHT_ADP8870) || defined(CONFIG_BACKLIGHT_ADP8870_MODULE)
1821         {
1822                 I2C_BOARD_INFO("adp8870", 0x2B),
1823                 .platform_data = (void *)&adp8870_pdata,
1824         },
1825 #endif
1826 #if defined(CONFIG_SND_SOC_ADAU1371) || defined(CONFIG_SND_SOC_ADAU1371_MODULE)
1827         {
1828                 I2C_BOARD_INFO("adau1371", 0x1A),
1829         },
1830 #endif
1831 #if defined(CONFIG_SND_SOC_ADAU1761) || defined(CONFIG_SND_SOC_ADAU1761_MODULE)
1832         {
1833                 I2C_BOARD_INFO("adau1761", 0x38),
1834         },
1835 #endif
1836 #if defined(CONFIG_SND_SOC_ADAU1361) || defined(CONFIG_SND_SOC_ADAU1361_MODULE)
1837         {
1838                 I2C_BOARD_INFO("adau1361", 0x38),
1839         },
1840 #endif
1841 #if defined(CONFIG_AD525X_DPOT) || defined(CONFIG_AD525X_DPOT_MODULE)
1842         {
1843                 I2C_BOARD_INFO("ad5258", 0x18),
1844         },
1845 #endif
1846 #if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
1847         {
1848                 I2C_BOARD_INFO("ssm2602", 0x1b),
1849         },
1850 #endif
1851 #if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
1852         {
1853                 I2C_BOARD_INFO("ad5398", 0xC),
1854                 .platform_data = (void *)&ad5398_i2c_platform_data,
1855         },
1856 #endif
1857 };
1858
1859 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1860 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1861 static struct resource bfin_sport0_uart_resources[] = {
1862         {
1863                 .start = SPORT0_TCR1,
1864                 .end = SPORT0_MRCS3+4,
1865                 .flags = IORESOURCE_MEM,
1866         },
1867         {
1868                 .start = IRQ_SPORT0_RX,
1869                 .end = IRQ_SPORT0_RX+1,
1870                 .flags = IORESOURCE_IRQ,
1871         },
1872         {
1873                 .start = IRQ_SPORT0_ERROR,
1874                 .end = IRQ_SPORT0_ERROR,
1875                 .flags = IORESOURCE_IRQ,
1876         },
1877 };
1878
1879 unsigned short bfin_sport0_peripherals[] = {
1880         P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
1881         P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
1882 };
1883
1884 static struct platform_device bfin_sport0_uart_device = {
1885         .name = "bfin-sport-uart",
1886         .id = 0,
1887         .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
1888         .resource = bfin_sport0_uart_resources,
1889         .dev = {
1890                 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
1891         },
1892 };
1893 #endif
1894 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1895 static struct resource bfin_sport1_uart_resources[] = {
1896         {
1897                 .start = SPORT1_TCR1,
1898                 .end = SPORT1_MRCS3+4,
1899                 .flags = IORESOURCE_MEM,
1900         },
1901         {
1902                 .start = IRQ_SPORT1_RX,
1903                 .end = IRQ_SPORT1_RX+1,
1904                 .flags = IORESOURCE_IRQ,
1905         },
1906         {
1907                 .start = IRQ_SPORT1_ERROR,
1908                 .end = IRQ_SPORT1_ERROR,
1909                 .flags = IORESOURCE_IRQ,
1910         },
1911 };
1912
1913 unsigned short bfin_sport1_peripherals[] = {
1914         P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
1915         P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
1916 };
1917
1918 static struct platform_device bfin_sport1_uart_device = {
1919         .name = "bfin-sport-uart",
1920         .id = 1,
1921         .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
1922         .resource = bfin_sport1_uart_resources,
1923         .dev = {
1924                 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
1925         },
1926 };
1927 #endif
1928 #endif
1929
1930 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
1931 #define CF_IDE_NAND_CARD_USE_HDD_INTERFACE
1932 /* #define CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE */
1933
1934 #ifdef CF_IDE_NAND_CARD_USE_HDD_INTERFACE
1935 #define PATA_INT        IRQ_PF5
1936 static struct pata_platform_info bfin_pata_platform_data = {
1937         .ioport_shift = 1,
1938         .irq_flags = IRQF_TRIGGER_HIGH | IRQF_DISABLED,
1939 };
1940
1941 static struct resource bfin_pata_resources[] = {
1942         {
1943                 .start = 0x20314020,
1944                 .end = 0x2031403F,
1945                 .flags = IORESOURCE_MEM,
1946         },
1947         {
1948                 .start = 0x2031401C,
1949                 .end = 0x2031401F,
1950                 .flags = IORESOURCE_MEM,
1951         },
1952         {
1953                 .start = PATA_INT,
1954                 .end = PATA_INT,
1955                 .flags = IORESOURCE_IRQ,
1956         },
1957 };
1958 #elif defined(CF_IDE_NAND_CARD_USE_CF_IN_COMMON_MEMORY_MODE)
1959 static struct pata_platform_info bfin_pata_platform_data = {
1960         .ioport_shift = 0,
1961 };
1962 /* CompactFlash Storage Card Memory Mapped Adressing
1963  * /REG = A11 = 1
1964  */
1965 static struct resource bfin_pata_resources[] = {
1966         {
1967                 .start = 0x20211800,
1968                 .end = 0x20211807,
1969                 .flags = IORESOURCE_MEM,
1970         },
1971         {
1972                 .start = 0x2021180E,    /* Device Ctl */
1973                 .end = 0x2021180E,
1974                 .flags = IORESOURCE_MEM,
1975         },
1976 };
1977 #endif
1978
1979 static struct platform_device bfin_pata_device = {
1980         .name = "pata_platform",
1981         .id = -1,
1982         .num_resources = ARRAY_SIZE(bfin_pata_resources),
1983         .resource = bfin_pata_resources,
1984         .dev = {
1985                 .platform_data = &bfin_pata_platform_data,
1986         }
1987 };
1988 #endif
1989
1990 static const unsigned int cclk_vlev_datasheet[] =
1991 {
1992         VRPAIR(VLEV_085, 250000000),
1993         VRPAIR(VLEV_090, 376000000),
1994         VRPAIR(VLEV_095, 426000000),
1995         VRPAIR(VLEV_100, 426000000),
1996         VRPAIR(VLEV_105, 476000000),
1997         VRPAIR(VLEV_110, 476000000),
1998         VRPAIR(VLEV_115, 476000000),
1999         VRPAIR(VLEV_120, 500000000),
2000         VRPAIR(VLEV_125, 533000000),
2001         VRPAIR(VLEV_130, 600000000),
2002 };
2003
2004 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
2005         .tuple_tab = cclk_vlev_datasheet,
2006         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
2007         .vr_settling_time = 25 /* us */,
2008 };
2009
2010 static struct platform_device bfin_dpmc = {
2011         .name = "bfin dpmc",
2012         .dev = {
2013                 .platform_data = &bfin_dmpc_vreg_data,
2014         },
2015 };
2016
2017 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
2018 static struct platform_device bfin_i2s = {
2019         .name = "bfin-i2s",
2020         .id = CONFIG_SND_BF5XX_SPORT_NUM,
2021         /* TODO: add platform data here */
2022 };
2023 #endif
2024
2025 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
2026 static struct platform_device bfin_tdm = {
2027         .name = "bfin-tdm",
2028         .id = CONFIG_SND_BF5XX_SPORT_NUM,
2029         /* TODO: add platform data here */
2030 };
2031 #endif
2032
2033 #if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
2034 static struct platform_device bfin_ac97 = {
2035         .name = "bfin-ac97",
2036         .id = CONFIG_SND_BF5XX_SPORT_NUM,
2037         /* TODO: add platform data here */
2038 };
2039 #endif
2040
2041 #if defined(CONFIG_REGULATOR_ADP_SWITCH) || defined(CONFIG_REGULATOR_ADP_SWITCH_MODULE)
2042 #define REGULATOR_ADP122        "adp122"
2043 #define REGULATOR_ADP150        "adp150"
2044
2045 static struct regulator_consumer_supply adp122_consumers = {
2046                 .supply = REGULATOR_ADP122,
2047 };
2048
2049 static struct regulator_consumer_supply adp150_consumers = {
2050                 .supply = REGULATOR_ADP150,
2051 };
2052
2053 static struct regulator_init_data adp_switch_regulator_data[] = {
2054         {
2055                 .constraints = {
2056                         .name = REGULATOR_ADP122,
2057                         .valid_ops_mask = REGULATOR_CHANGE_STATUS,
2058                 },
2059                 .num_consumer_supplies = 1,     /* only 1 */
2060                 .consumer_supplies     = &adp122_consumers,
2061                 .driver_data           = (void *)GPIO_PF2, /* gpio port only */
2062         },
2063         {
2064                 .constraints = {
2065                         .name = REGULATOR_ADP150,
2066                         .valid_ops_mask = REGULATOR_CHANGE_STATUS,
2067                 },
2068                 .num_consumer_supplies = 1,     /* only 1 */
2069                 .consumer_supplies     = &adp150_consumers,
2070                 .driver_data           = (void *)GPIO_PF3, /* gpio port only */
2071         },
2072 };
2073
2074 static struct adp_switch_platform_data adp_switch_pdata = {
2075         .regulator_num = ARRAY_SIZE(adp_switch_regulator_data),
2076         .regulator_data = adp_switch_regulator_data,
2077 };
2078
2079 static struct platform_device adp_switch_device = {
2080         .name = "adp_switch",
2081         .id = 0,
2082         .dev = {
2083                 .platform_data = &adp_switch_pdata,
2084         },
2085 };
2086
2087 #if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
2088         defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
2089 static struct regulator_bulk_data adp122_bulk_data = {
2090         .supply = REGULATOR_ADP122,
2091 };
2092
2093 static struct regulator_userspace_consumer_data adp122_userspace_comsumer_data = {
2094         .name = REGULATOR_ADP122,
2095         .num_supplies = 1,
2096         .supplies = &adp122_bulk_data,
2097 };
2098
2099 static struct platform_device adp122_userspace_consumer_device = {
2100         .name = "reg-userspace-consumer",
2101         .id = 0,
2102         .dev = {
2103                 .platform_data = &adp122_userspace_comsumer_data,
2104         },
2105 };
2106
2107 static struct regulator_bulk_data adp150_bulk_data = {
2108         .supply = REGULATOR_ADP150,
2109 };
2110
2111 static struct regulator_userspace_consumer_data adp150_userspace_comsumer_data = {
2112         .name = REGULATOR_ADP150,
2113         .num_supplies = 1,
2114         .supplies = &adp150_bulk_data,
2115 };
2116
2117 static struct platform_device adp150_userspace_consumer_device = {
2118         .name = "reg-userspace-consumer",
2119         .id = 1,
2120         .dev = {
2121                 .platform_data = &adp150_userspace_comsumer_data,
2122         },
2123 };
2124 #endif
2125 #endif
2126
2127
2128 static struct platform_device *stamp_devices[] __initdata = {
2129
2130         &bfin_dpmc,
2131
2132 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
2133         &bfin_pcmcia_cf_device,
2134 #endif
2135
2136 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
2137         &rtc_device,
2138 #endif
2139
2140 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
2141         &sl811_hcd_device,
2142 #endif
2143
2144 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
2145         &isp1362_hcd_device,
2146 #endif
2147
2148 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
2149         &bfin_isp1760_device,
2150 #endif
2151
2152 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
2153         &smc91x_device,
2154 #endif
2155
2156 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
2157         &dm9000_device,
2158 #endif
2159
2160 #if defined(CONFIG_CAN_BFIN) || defined(CONFIG_CAN_BFIN_MODULE)
2161         &bfin_can_device,
2162 #endif
2163
2164 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
2165         &bfin_mii_bus,
2166         &bfin_mac_device,
2167 #endif
2168
2169 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
2170         &net2272_bfin_device,
2171 #endif
2172
2173 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
2174         &bfin_spi0_device,
2175 #endif
2176
2177 #if defined(CONFIG_SPI_BFIN_SPORT) || defined(CONFIG_SPI_BFIN_SPORT_MODULE)
2178         &bfin_sport_spi0_device,
2179         &bfin_sport_spi1_device,
2180 #endif
2181
2182 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
2183         &bfin_fb_device,
2184 #endif
2185
2186 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
2187         &bfin_lq035q1_device,
2188 #endif
2189
2190 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
2191 #ifdef CONFIG_SERIAL_BFIN_UART0
2192         &bfin_uart0_device,
2193 #endif
2194 #ifdef CONFIG_SERIAL_BFIN_UART1
2195         &bfin_uart1_device,
2196 #endif
2197 #endif
2198
2199 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
2200 #ifdef CONFIG_BFIN_SIR0
2201         &bfin_sir0_device,
2202 #endif
2203 #ifdef CONFIG_BFIN_SIR1
2204         &bfin_sir1_device,
2205 #endif
2206 #endif
2207
2208 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
2209         &i2c_bfin_twi_device,
2210 #endif
2211
2212 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
2213 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
2214         &bfin_sport0_uart_device,
2215 #endif
2216 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
2217         &bfin_sport1_uart_device,
2218 #endif
2219 #endif
2220
2221 #if defined(CONFIG_PATA_PLATFORM) || defined(CONFIG_PATA_PLATFORM_MODULE)
2222         &bfin_pata_device,
2223 #endif
2224
2225 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
2226         &bfin_device_gpiokeys,
2227 #endif
2228
2229 #if defined(CONFIG_MTD_NAND_PLATFORM) || defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
2230         &bfin_async_nand_device,
2231 #endif
2232
2233 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
2234         &stamp_flash_device,
2235 #endif
2236
2237 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
2238         &bfin_i2s,
2239 #endif
2240
2241 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
2242         &bfin_tdm,
2243 #endif
2244
2245 #if defined(CONFIG_SND_BF5XX_AC97) || defined(CONFIG_SND_BF5XX_AC97_MODULE)
2246         &bfin_ac97,
2247 #endif
2248 #if defined(CONFIG_REGULATOR_AD5398) || defined(CONFIG_REGULATOR_AD5398_MODULE)
2249 #if defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER) || \
2250         defined(CONFIG_REGULATOR_VIRTUAL_CONSUMER_MODULE)
2251         &ad5398_virt_consumer_device,
2252 #endif
2253 #if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
2254         defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
2255         &ad5398_userspace_consumer_device,
2256 #endif
2257 #endif
2258
2259 #if defined(CONFIG_REGULATOR_ADP_SWITCH) || defined(CONFIG_REGULATOR_ADP_SWITCH_MODULE)
2260         &adp_switch_device,
2261 #if defined(CONFIG_REGULATOR_USERSPACE_CONSUMER) || \
2262         defined(CONFIG_REGULATOR_USERSPACE_CONSUMER_MODULE)
2263         &adp122_userspace_consumer_device,
2264         &adp150_userspace_consumer_device,
2265 #endif
2266 #endif
2267 };
2268
2269 static int __init stamp_init(void)
2270 {
2271         printk(KERN_INFO "%s(): registering device resources\n", __func__);
2272         bfin_plat_nand_init();
2273         adf702x_mac_init();
2274         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
2275         i2c_register_board_info(0, bfin_i2c_board_info,
2276                                 ARRAY_SIZE(bfin_i2c_board_info));
2277         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
2278
2279         return 0;
2280 }
2281
2282 arch_initcall(stamp_init);
2283
2284
2285 static struct platform_device *stamp_early_devices[] __initdata = {
2286 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
2287 #ifdef CONFIG_SERIAL_BFIN_UART0
2288         &bfin_uart0_device,
2289 #endif
2290 #ifdef CONFIG_SERIAL_BFIN_UART1
2291         &bfin_uart1_device,
2292 #endif
2293 #endif
2294
2295 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
2296 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
2297         &bfin_sport0_uart_device,
2298 #endif
2299 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
2300         &bfin_sport1_uart_device,
2301 #endif
2302 #endif
2303 };
2304
2305 void __init native_machine_early_platform_add_devices(void)
2306 {
2307         printk(KERN_INFO "register early platform devices\n");
2308         early_platform_add_devices(stamp_early_devices,
2309                 ARRAY_SIZE(stamp_early_devices));
2310 }
2311
2312 void native_machine_restart(char *cmd)
2313 {
2314         /* workaround reboot hang when booting from SPI */
2315         if ((bfin_read_SYSCR() & 0x7) == 0x3)
2316                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
2317 }
2318
2319 /*
2320  * Currently the MAC address is saved in Flash by U-Boot
2321  */
2322 #define FLASH_MAC       0x203f0000
2323 void bfin_get_ether_addr(char *addr)
2324 {
2325         *(u32 *)(&(addr[0])) = bfin_read32(FLASH_MAC);
2326         *(u16 *)(&(addr[4])) = bfin_read16(FLASH_MAC + 4);
2327 }
2328 EXPORT_SYMBOL(bfin_get_ether_addr);