arch/arm/mach-davinci/board-neuros-osd2.c

   1 /*
   2  * Neuros Technologies OSD2 board support
   3  *
   4  * Modified from original 644X-EVM board support.
   5  * 2008 (c) Neuros Technology, LLC.
   6  * 2009 (c) Jorge Luis Zapata Muga <jorgeluis.zapata@gmail.com>
   7  * 2009 (c) Andrey A. Porodko <Andrey.Porodko@gmail.com>
   8  *
   9  * The Neuros OSD 2.0 is the hardware component of the Neuros Open
  10  * Internet Television Platform. Hardware is very close to TI
  11  * DM644X-EVM board. It has:
  12  *      DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
  13  *      USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
  14  *      Additionaly realtime clock, IR remote control receiver,
  15  *      IR Blaster based on MSP430 (firmware although is different
  16  *      from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
  17  *      with PATA interface, two muxed red-green leds.
  18  *
  19  * For more information please refer to
  20  *              http://wiki.neurostechnology.com/index.php/OSD_2.0_HD
  21  *
  22  * This file is licensed under the terms of the GNU General Public
  23  * License version 2. This program is licensed "as is" without any
  24  * warranty of any kind, whether express or implied.
  25  */
  26 #include <linux/platform_device.h>
  27 #include <linux/gpio.h>
  28 #include <linux/mtd/partitions.h>
  29
  30 #include <asm/mach-types.h>
  31 #include <asm/mach/arch.h>
  32
  33 #include <mach/dm644x.h>
  34 #include <mach/common.h>
  35 #include <mach/i2c.h>
  36 #include <mach/serial.h>
  37 #include <mach/mux.h>
  38 #include <mach/nand.h>
  39 #include <mach/mmc.h>
  40 #include <mach/usb.h>
  41
  42 #define NEUROS_OSD2_PHY_ID              "0:01"
  43 #define LXT971_PHY_ID                   0x001378e2
  44 #define LXT971_PHY_MASK                 0xfffffff0
  45
  46 #define NTOSD2_AUDIOSOC_I2C_ADDR        0x18
  47 #define NTOSD2_MSP430_I2C_ADDR          0x59
  48 #define NTOSD2_MSP430_IRQ               2
  49
  50 /* Neuros OSD2 has a Samsung 256 MByte NAND flash (Dev ID of 0xAA,
  51  * 2048 blocks in the device, 64 pages per block, 2048 bytes per
  52  * page.
  53  */
  54
  55 #define NAND_BLOCK_SIZE         SZ_128K
  56
  57 static struct mtd_partition davinci_ntosd2_nandflash_partition[] = {
  58         {
  59                 /* UBL (a few copies) plus U-Boot */
  60                 .name           = "bootloader",
  61                 .offset         = 0,
  62                 .size           = 15 * NAND_BLOCK_SIZE,
  63                 .mask_flags     = MTD_WRITEABLE, /* force read-only */
  64         }, {
  65                 /* U-Boot environment */
  66                 .name           = "params",
  67                 .offset         = MTDPART_OFS_APPEND,
  68                 .size           = 1 * NAND_BLOCK_SIZE,
  69                 .mask_flags     = 0,
  70         }, {
  71                 /* Kernel */
  72                 .name           = "kernel",
  73                 .offset         = MTDPART_OFS_APPEND,
  74                 .size           = SZ_4M,
  75                 .mask_flags     = 0,
  76         }, {
  77                 /* File System */
  78                 .name           = "filesystem",
  79                 .offset         = MTDPART_OFS_APPEND,
  80                 .size           = MTDPART_SIZ_FULL,
  81                 .mask_flags     = 0,
  82         }
  83         /* A few blocks at end hold a flash Bad Block Table. */
  84 };
  85
  86 static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = {
  87         .parts          = davinci_ntosd2_nandflash_partition,
  88         .nr_parts       = ARRAY_SIZE(davinci_ntosd2_nandflash_partition),
  89         .ecc_mode       = NAND_ECC_HW,
  90         .options        = NAND_USE_FLASH_BBT,
  91 };
  92
  93 static struct resource davinci_ntosd2_nandflash_resource[] = {
  94         {
  95                 .start          = DM644X_ASYNC_EMIF_DATA_CE0_BASE,
  96                 .end            = DM644X_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
  97                 .flags          = IORESOURCE_MEM,
  98         }, {
  99                 .start          = DM644X_ASYNC_EMIF_CONTROL_BASE,
 100                 .end            = DM644X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
 101                 .flags          = IORESOURCE_MEM,
 102         },
 103 };
 104
 105 static struct platform_device davinci_ntosd2_nandflash_device = {
 106         .name           = "davinci_nand",
 107         .id             = 0,
 108         .dev            = {
 109                 .platform_data  = &davinci_ntosd2_nandflash_data,
 110         },
 111         .num_resources  = ARRAY_SIZE(davinci_ntosd2_nandflash_resource),
 112         .resource       = davinci_ntosd2_nandflash_resource,
 113 };
 114
 115 static u64 davinci_fb_dma_mask = DMA_BIT_MASK(32);
 116
 117 static struct platform_device davinci_fb_device = {
 118         .name           = "davincifb",
 119         .id             = -1,
 120         .dev = {
 121                 .dma_mask               = &davinci_fb_dma_mask,
 122                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 123         },
 124         .num_resources = 0,
 125 };
 126
 127 static struct snd_platform_data dm644x_ntosd2_snd_data;
 128
 129 static struct gpio_led ntosd2_leds[] = {
 130         { .name = "led1_green", .gpio = GPIO(10), },
 131         { .name = "led1_red",   .gpio = GPIO(11), },
 132         { .name = "led2_green", .gpio = GPIO(12), },
 133         { .name = "led2_red",   .gpio = GPIO(13), },
 134 };
 135
 136 static struct gpio_led_platform_data ntosd2_leds_data = {
 137         .num_leds       = ARRAY_SIZE(ntosd2_leds),
 138         .leds           = ntosd2_leds,
 139 };
 140
 141 static struct platform_device ntosd2_leds_dev = {
 142         .name = "leds-gpio",
 143         .id   = -1,
 144         .dev = {
 145                 .platform_data          = &ntosd2_leds_data,
 146         },
 147 };
 148
 149
 150 static struct platform_device *davinci_ntosd2_devices[] __initdata = {
 151         &davinci_fb_device,
 152         &ntosd2_leds_dev,
 153 };
 154
 155 static struct davinci_uart_config uart_config __initdata = {
 156         .enabled_uarts = (1 << 0),
 157 };
 158
 159 static void __init davinci_ntosd2_map_io(void)
 160 {
 161         dm644x_init();
 162 }
 163
 164 /*
 165  I2C initialization
 166 */
 167 static struct davinci_i2c_platform_data ntosd2_i2c_pdata = {
 168         .bus_freq       = 20 /* kHz */,
 169         .bus_delay      = 100 /* usec */,
 170 };
 171
 172 static struct i2c_board_info __initdata ntosd2_i2c_info[] =  {
 173 };
 174
 175 static  int ntosd2_init_i2c(void)
 176 {
 177         int     status;
 178
 179         davinci_init_i2c(&ntosd2_i2c_pdata);
 180         status = gpio_request(NTOSD2_MSP430_IRQ, ntosd2_i2c_info[0].type);
 181         if (status == 0) {
 182                 status = gpio_direction_input(NTOSD2_MSP430_IRQ);
 183                 if (status == 0) {
 184                         status = gpio_to_irq(NTOSD2_MSP430_IRQ);
 185                         if (status > 0) {
 186                                 ntosd2_i2c_info[0].irq = status;
 187                                 i2c_register_board_info(1,
 188                                         ntosd2_i2c_info,
 189                                         ARRAY_SIZE(ntosd2_i2c_info));
 190                         }
 191                 }
 192         }
 193         return status;
 194 }
 195
 196 static struct davinci_mmc_config davinci_ntosd2_mmc_config = {
 197         .wires          = 4,
 198         .version        = MMC_CTLR_VERSION_1
 199 };
 200
 201
 202 #if defined(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
 203         defined(CONFIG_BLK_DEV_PALMCHIP_BK3710_MODULE)
 204 #define HAS_ATA 1
 205 #else
 206 #define HAS_ATA 0
 207 #endif
 208
 209 #if defined(CONFIG_MTD_NAND_DAVINCI) || \
 210         defined(CONFIG_MTD_NAND_DAVINCI_MODULE)
 211 #define HAS_NAND 1
 212 #else
 213 #define HAS_NAND 0
 214 #endif
 215
 216 static __init void davinci_ntosd2_init(void)
 217 {
 218         struct clk *aemif_clk;
 219         struct davinci_soc_info *soc_info = &davinci_soc_info;
 220         int     status;
 221
 222         aemif_clk = clk_get(NULL, "aemif");
 223         clk_enable(aemif_clk);
 224
 225         if (HAS_ATA) {
 226                 if (HAS_NAND)
 227                         pr_warning("WARNING: both IDE and Flash are "
 228                                 "enabled, but they share AEMIF pins.\n"
 229                                 "\tDisable IDE for NAND/NOR support.\n");
 230                 davinci_init_ide();
 231         } else if (HAS_NAND) {
 232                 davinci_cfg_reg(DM644X_HPIEN_DISABLE);
 233                 davinci_cfg_reg(DM644X_ATAEN_DISABLE);
 234
 235                 /* only one device will be jumpered and detected */
 236                 if (HAS_NAND)
 237                         platform_device_register(
 238                                         &davinci_ntosd2_nandflash_device);
 239         }
 240
 241         platform_add_devices(davinci_ntosd2_devices,
 242                                 ARRAY_SIZE(davinci_ntosd2_devices));
 243
 244         /* Initialize I2C interface specific for this board */
 245         status = ntosd2_init_i2c();
 246         if (status < 0)
 247                 pr_warning("davinci_ntosd2_init: msp430 irq setup failed:"
 248                                                 "        %d\n", status);
 249
 250         davinci_serial_init(&uart_config);
 251         dm644x_init_asp(&dm644x_ntosd2_snd_data);
 252
 253         soc_info->emac_pdata->phy_id = NEUROS_OSD2_PHY_ID;
 254
 255         davinci_setup_usb(1000, 8);
 256         /*
 257          * Mux the pins to be GPIOs, VLYNQEN is already done at startup.
 258          * The AEAWx are five new AEAW pins that can be muxed by separately.
 259          * They are a bitmask for GPIO management. According TI
 260          * documentation (http://www.ti.com/lit/gpn/tms320dm6446) to employ
 261          * gpio(10,11,12,13) for leds any combination of bits works except
 262          * four last. So we are to reset all five.
 263          */
 264         davinci_cfg_reg(DM644X_AEAW0);
 265         davinci_cfg_reg(DM644X_AEAW1);
 266         davinci_cfg_reg(DM644X_AEAW2);
 267         davinci_cfg_reg(DM644X_AEAW3);
 268         davinci_cfg_reg(DM644X_AEAW4);
 269
 270         davinci_setup_mmc(0, &davinci_ntosd2_mmc_config);
 271 }
 272
 273 MACHINE_START(NEUROS_OSD2, "Neuros OSD2")
 274         /* Maintainer: Neuros Technologies <neuros@groups.google.com> */
 275         .boot_params    = (DAVINCI_DDR_BASE + 0x100),
 276         .map_io          = davinci_ntosd2_map_io,
 277         .init_irq       = davinci_irq_init,
 278         .timer          = &davinci_timer,
 279         .init_machine = davinci_ntosd2_init,
 280 MACHINE_END