2 * DM355 leopard board support
4 * Based on board-dm355-evm.c
6 * This file is licensed under the terms of the GNU General Public
7 * License version 2. This program is licensed "as is" without any
8 * warranty of any kind, whether express or implied.
10 #include <linux/kernel.h>
11 #include <linux/module.h>
12 #include <linux/init.h>
13 #include <linux/dma-mapping.h>
14 #include <linux/platform_device.h>
15 #include <linux/mtd/mtd.h>
16 #include <linux/mtd/partitions.h>
17 #include <linux/mtd/nand.h>
18 #include <linux/i2c.h>
20 #include <linux/gpio.h>
21 #include <linux/clk.h>
22 #include <linux/spi/spi.h>
23 #include <linux/spi/eeprom.h>
25 #include <asm/setup.h>
26 #include <asm/mach-types.h>
27 #include <asm/mach/arch.h>
28 #include <asm/mach/map.h>
29 #include <asm/mach/flash.h>
31 #include <mach/hardware.h>
32 #include <mach/dm355.h>
34 #include <mach/common.h>
36 #include <mach/serial.h>
37 #include <mach/nand.h>
39 #define DAVINCI_ASYNC_EMIF_CONTROL_BASE 0x01e10000
40 #define DAVINCI_ASYNC_EMIF_DATA_CE0_BASE 0x02000000
42 /* NOTE: this is geared for the standard config, with a socketed
43 * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you
44 * swap chips, maybe with a different block size, partitioning may
47 #define NAND_BLOCK_SIZE SZ_128K
49 static struct mtd_partition davinci_nand_partitions[] = {
51 /* UBL (a few copies) plus U-Boot */
54 .size = 15 * NAND_BLOCK_SIZE,
55 .mask_flags = MTD_WRITEABLE, /* force read-only */
57 /* U-Boot environment */
59 .offset = MTDPART_OFS_APPEND,
60 .size = 1 * NAND_BLOCK_SIZE,
64 .offset = MTDPART_OFS_APPEND,
68 .name = "filesystem1",
69 .offset = MTDPART_OFS_APPEND,
73 .name = "filesystem2",
74 .offset = MTDPART_OFS_APPEND,
75 .size = MTDPART_SIZ_FULL,
78 /* two blocks with bad block table (and mirror) at the end */
81 static struct davinci_nand_pdata davinci_nand_data = {
82 .mask_chipsel = BIT(14),
83 .parts = davinci_nand_partitions,
84 .nr_parts = ARRAY_SIZE(davinci_nand_partitions),
85 .ecc_mode = NAND_ECC_HW_SYNDROME,
86 .options = NAND_USE_FLASH_BBT,
89 static struct resource davinci_nand_resources[] = {
91 .start = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE,
92 .end = DAVINCI_ASYNC_EMIF_DATA_CE0_BASE + SZ_32M - 1,
93 .flags = IORESOURCE_MEM,
95 .start = DAVINCI_ASYNC_EMIF_CONTROL_BASE,
96 .end = DAVINCI_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
97 .flags = IORESOURCE_MEM,
101 static struct platform_device davinci_nand_device = {
102 .name = "davinci_nand",
105 .num_resources = ARRAY_SIZE(davinci_nand_resources),
106 .resource = davinci_nand_resources,
109 .platform_data = &davinci_nand_data,
113 static struct davinci_i2c_platform_data i2c_pdata = {
114 .bus_freq = 400 /* kHz */,
115 .bus_delay = 0 /* usec */,
118 static int leopard_mmc_gpio = -EINVAL;
120 static void dm355leopard_mmcsd_gpios(unsigned gpio)
122 gpio_request(gpio + 0, "mmc0_ro");
123 gpio_request(gpio + 1, "mmc0_cd");
124 gpio_request(gpio + 2, "mmc1_ro");
125 gpio_request(gpio + 3, "mmc1_cd");
127 /* we "know" these are input-only so we don't
128 * need to call gpio_direction_input()
131 leopard_mmc_gpio = gpio;
134 static struct i2c_board_info dm355leopard_i2c_info[] = {
135 { I2C_BOARD_INFO("dm355leopard_msp", 0x25),
136 .platform_data = dm355leopard_mmcsd_gpios,
138 /* { I2C_BOARD_INFO("tlv320aic3x", 0x1b), }, */
139 /* { I2C_BOARD_INFO("tvp5146", 0x5d), }, */
142 static void __init leopard_init_i2c(void)
144 davinci_init_i2c(&i2c_pdata);
146 gpio_request(5, "dm355leopard_msp");
147 gpio_direction_input(5);
148 dm355leopard_i2c_info[0].irq = gpio_to_irq(5);
150 i2c_register_board_info(1, dm355leopard_i2c_info,
151 ARRAY_SIZE(dm355leopard_i2c_info));
154 static struct resource dm355leopard_dm9000_rsrc[] = {
159 .flags = IORESOURCE_MEM,
164 .flags = IORESOURCE_MEM,
166 .flags = IORESOURCE_IRQ
167 | IORESOURCE_IRQ_HIGHEDGE /* rising (active high) */,
171 static struct platform_device dm355leopard_dm9000 = {
174 .resource = dm355leopard_dm9000_rsrc,
175 .num_resources = ARRAY_SIZE(dm355leopard_dm9000_rsrc),
178 static struct platform_device *davinci_leopard_devices[] __initdata = {
179 &dm355leopard_dm9000,
180 &davinci_nand_device,
183 static struct davinci_uart_config uart_config __initdata = {
184 .enabled_uarts = (1 << 0),
187 static void __init dm355_leopard_map_io(void)
189 davinci_map_common_io();
193 /* Don't connect anything to J10 unless you're only using USB host
194 * mode *and* have to do so with some kind of gender-bender. If
195 * you have proper Mini-B or Mini-A cables (or Mini-A adapters)
196 * the ID pin won't need any help.
198 #ifdef CONFIG_USB_MUSB_PERIPHERAL
199 #define USB_ID_VALUE 0 /* ID pulled high; *should* float */
201 #define USB_ID_VALUE 1 /* ID pulled low */
204 static struct spi_eeprom at25640a = {
205 .byte_len = SZ_64K / 8,
211 static struct spi_board_info dm355_leopard_spi_info[] __initconst = {
214 .platform_data = &at25640a,
215 .max_speed_hz = 10 * 1000 * 1000, /* at 3v3 */
222 static __init void dm355_leopard_init(void)
226 gpio_request(9, "dm9000");
227 gpio_direction_input(9);
228 dm355leopard_dm9000_rsrc[2].start = gpio_to_irq(9);
230 aemif = clk_get(&dm355leopard_dm9000.dev, "aemif");
232 WARN("%s: unable to get AEMIF clock\n", __func__);
236 platform_add_devices(davinci_leopard_devices,
237 ARRAY_SIZE(davinci_leopard_devices));
239 davinci_serial_init(&uart_config);
241 /* NOTE: NAND flash timings set by the UBL are slower than
242 * needed by MT29F16G08FAA chips ... EMIF.A1CR is 0x40400204
243 * but could be 0x0400008c for about 25% faster page reads.
246 gpio_request(2, "usb_id_toggle");
247 gpio_direction_output(2, USB_ID_VALUE);
248 /* irlml6401 switches over 1A in under 8 msec */
251 dm355_init_spi0(BIT(0), dm355_leopard_spi_info,
252 ARRAY_SIZE(dm355_leopard_spi_info));
255 static __init void dm355_leopard_irq_init(void)
260 MACHINE_START(DM355_LEOPARD, "DaVinci DM355 leopard")
262 .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
263 .boot_params = (0x80000100),
264 .map_io = dm355_leopard_map_io,
265 .init_irq = dm355_leopard_irq_init,
266 .timer = &davinci_timer,
267 .init_machine = dm355_leopard_init,