2 * Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License as published by
7 * the Free Software Foundation; either version 2 of the License, or
8 * (at your option) any later version.
10 * This program is distributed in the hope that it will be useful,
11 * but WITHOUT ANY WARRANTY; without even the implied warranty of
12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
13 * GNU General Public License for more details.
15 * You should have received a copy of the GNU General Public License
16 * along with this program; if not, write to the Free Software
17 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
21 #include <linux/platform_device.h>
22 #include <linux/gpio.h>
23 #include <linux/w1-gpio.h>
25 #include <asm/mach-types.h>
26 #include <asm/mach/arch.h>
28 #include <mach/at91sam9_smc.h>
29 #include <mach/hardware.h>
37 void __init stamp9g20_init_early(void)
39 /* Initialize processor: 18.432 MHz crystal */
40 at91_initialize(18432000);
46 static struct atmel_nand_data __initdata nand_data = {
49 .rdy_pin = AT91_PIN_PC13,
50 .enable_pin = AT91_PIN_PC14,
53 .ecc_mode = NAND_ECC_SOFT,
56 static struct sam9_smc_config __initdata nand_smc_config = {
70 .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
74 static void __init add_device_nand(void)
76 /* configure chip-select 3 (NAND) */
77 sam9_smc_configure(0, 3, &nand_smc_config);
79 at91_add_device_nand(&nand_data);
85 * det_pin, wp_pin and vcc_pin are not connected
87 static struct mci_platform_data __initdata mmc_data = {
99 static struct at91_usbh_data __initdata usbh_data = {
101 .vbus_pin = {-EINVAL, -EINVAL},
102 .overcurrent_pin= {-EINVAL, -EINVAL},
109 static struct at91_udc_data __initdata portuxg20_udc_data = {
110 .vbus_pin = AT91_PIN_PC7,
111 .pullup_pin = -EINVAL, /* pull-up driven by UDC */
114 static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
115 .vbus_pin = AT91_PIN_PA22,
116 .pullup_pin = -EINVAL, /* pull-up driven by UDC */
121 * MACB Ethernet device
123 static struct macb_platform_data __initdata macb_data = {
124 .phy_irq_pin = AT91_PIN_PA28,
132 static struct gpio_led portuxg20_leds[] = {
135 .gpio = AT91_PIN_PC5,
136 .default_trigger = "none",
139 .gpio = AT91_PIN_PC4,
140 .default_trigger = "none",
143 .gpio = AT91_PIN_PC10,
144 .default_trigger = "heartbeat",
148 static struct gpio_led stamp9g20evb_leds[] = {
151 .gpio = AT91_PIN_PB18,
153 .default_trigger = "none",
156 .gpio = AT91_PIN_PB19,
158 .default_trigger = "none",
161 .gpio = AT91_PIN_PB20,
163 .default_trigger = "heartbeat",
171 static struct spi_board_info portuxg20_spi_devices[] = {
173 .modalias = "spidev",
175 .max_speed_hz = 1 * 1000 * 1000,
178 .modalias = "spidev",
180 .max_speed_hz = 1 * 1000 * 1000,
189 static struct w1_gpio_platform_data w1_gpio_pdata = {
190 .pin = AT91_PIN_PA29,
192 .ext_pullup_enable_pin = -EINVAL,
195 static struct platform_device w1_device = {
198 .dev.platform_data = &w1_gpio_pdata,
203 at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
204 at91_set_multi_drive(w1_gpio_pdata.pin, 1);
205 platform_device_register(&w1_device);
209 void __init stamp9g20_board_init(void)
212 /* DGBU on ttyS0. (Rx & Tx only) */
213 at91_register_uart(0, 0, 0);
214 at91_add_device_serial();
218 at91_add_device_mci(0, &mmc_data);
223 static void __init portuxg20_board_init(void)
225 /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
226 at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
227 | ATMEL_UART_DTR | ATMEL_UART_DSR
228 | ATMEL_UART_DCD | ATMEL_UART_RI);
230 /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) */
231 at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
233 /* USART2 on ttyS3. (Rx, Tx, CTS, RTS) */
234 at91_register_uart(AT91SAM9260_ID_US2, 3, ATMEL_UART_CTS | ATMEL_UART_RTS);
236 /* USART4 on ttyS5. (Rx, Tx only) */
237 at91_register_uart(AT91SAM9260_ID_US4, 5, 0);
239 /* USART5 on ttyS6. (Rx, Tx only) */
240 at91_register_uart(AT91SAM9260_ID_US5, 6, 0);
241 stamp9g20_board_init();
243 at91_add_device_usbh(&usbh_data);
245 at91_add_device_udc(&portuxg20_udc_data);
247 at91_add_device_eth(&macb_data);
249 at91_add_device_i2c(NULL, 0);
251 at91_add_device_spi(portuxg20_spi_devices, ARRAY_SIZE(portuxg20_spi_devices));
253 at91_gpio_leds(portuxg20_leds, ARRAY_SIZE(portuxg20_leds));
256 static void __init stamp9g20evb_board_init(void)
258 /* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
259 at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
260 | ATMEL_UART_DTR | ATMEL_UART_DSR
261 | ATMEL_UART_DCD | ATMEL_UART_RI);
262 stamp9g20_board_init();
264 at91_add_device_usbh(&usbh_data);
266 at91_add_device_udc(&stamp9g20evb_udc_data);
268 at91_add_device_eth(&macb_data);
270 at91_add_device_i2c(NULL, 0);
272 at91_gpio_leds(stamp9g20evb_leds, ARRAY_SIZE(stamp9g20evb_leds));
275 MACHINE_START(PORTUXG20, "taskit PortuxG20")
276 /* Maintainer: taskit GmbH */
277 .init_time = at91sam926x_pit_init,
278 .map_io = at91_map_io,
279 .handle_irq = at91_aic_handle_irq,
280 .init_early = stamp9g20_init_early,
281 .init_irq = at91_init_irq_default,
282 .init_machine = portuxg20_board_init,
285 MACHINE_START(STAMP9G20, "taskit Stamp9G20")
286 /* Maintainer: taskit GmbH */
287 .init_time = at91sam926x_pit_init,
288 .map_io = at91_map_io,
289 .handle_irq = at91_aic_handle_irq,
290 .init_early = stamp9g20_init_early,
291 .init_irq = at91_init_irq_default,
292 .init_machine = stamp9g20evb_board_init,