arch/arm/mach-at91/board-eco920.c

   1 /*
   2  * This program is free software; you can redistribute it and/or modify
   3  * it under the terms of the GNU General Public License as published by
   4  * the Free Software Foundation; either version 2 of the License, or
   5  * (at your option) any later version.
   6  *
   7  * This program is distributed in the hope that it will be useful,
   8  * but WITHOUT ANY WARRANTY; without even the implied warranty of
   9  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  10  * GNU General Public License for more details.
  11  *
  12  * You should have received a copy of the GNU General Public License
  13  * along with this program; if not, write to the Free Software
  14  * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
  15  */
  16
  17 #include <linux/init.h>
  18 #include <linux/platform_device.h>
  19 #include <linux/mtd/physmap.h>
  20 #include <linux/gpio.h>
  21
  22 #include <asm/mach-types.h>
  23
  24 #include <asm/mach/arch.h>
  25 #include <asm/mach/map.h>
  26
  27 #include <mach/board.h>
  28 #include <mach/at91rm9200_mc.h>
  29 #include <mach/at91_ramc.h>
  30 #include <mach/cpu.h>
  31
  32 #include "generic.h"
  33
  34 static void __init eco920_init_early(void)
  35 {
  36         /* Set cpu type: PQFP */
  37         at91rm9200_set_type(ARCH_REVISON_9200_PQFP);
  38
  39         at91_initialize(18432000);
  40 }
  41
  42 static struct macb_platform_data __initdata eco920_eth_data = {
  43         .phy_irq_pin    = AT91_PIN_PC2,
  44         .is_rmii        = 1,
  45 };
  46
  47 static struct at91_usbh_data __initdata eco920_usbh_data = {
  48         .ports          = 1,
  49         .vbus_pin       = {-EINVAL, -EINVAL},
  50         .overcurrent_pin= {-EINVAL, -EINVAL},
  51 };
  52
  53 static struct at91_udc_data __initdata eco920_udc_data = {
  54         .vbus_pin       = AT91_PIN_PB12,
  55         .pullup_pin     = AT91_PIN_PB13,
  56 };
  57
  58 static struct at91_mmc_data __initdata eco920_mmc_data = {
  59         .slot_b         = 0,
  60         .wire4          = 0,
  61         .det_pin        = -EINVAL,
  62         .wp_pin         = -EINVAL,
  63         .vcc_pin        = -EINVAL,
  64 };
  65
  66 static struct physmap_flash_data eco920_flash_data = {
  67         .width  = 2,
  68 };
  69
  70 static struct resource eco920_flash_resource = {
  71         .start          = 0x11000000,
  72         .end            = 0x11ffffff,
  73         .flags          = IORESOURCE_MEM,
  74 };
  75
  76 static struct platform_device eco920_flash = {
  77         .name           = "physmap-flash",
  78         .id             = 0,
  79         .dev            = {
  80                 .platform_data  = &eco920_flash_data,
  81         },
  82         .resource       = &eco920_flash_resource,
  83         .num_resources  = 1,
  84 };
  85
  86 static struct spi_board_info eco920_spi_devices[] = {
  87         {       /* CAN controller */
  88                 .modalias       = "tlv5638",
  89                 .chip_select    = 3,
  90                 .max_speed_hz   = 20 * 1000 * 1000,
  91                 .mode           = SPI_CPHA,
  92         },
  93 };
  94
  95 static void __init eco920_board_init(void)
  96 {
  97         /* Setup the LEDs */
  98         at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
  99         /* DBGU on ttyS0. (Rx & Tx only */
 100         at91_register_uart(0, 0, 0);
 101         at91_add_device_serial();
 102         at91_add_device_eth(&eco920_eth_data);
 103         at91_add_device_usbh(&eco920_usbh_data);
 104         at91_add_device_udc(&eco920_udc_data);
 105
 106         at91_add_device_mmc(0, &eco920_mmc_data);
 107         platform_device_register(&eco920_flash);
 108
 109         at91_ramc_write(0, AT91_SMC_CSR(7),     AT91_SMC_RWHOLD_(1)
 110                                 | AT91_SMC_RWSETUP_(1)
 111                                 | AT91_SMC_DBW_8
 112                                 | AT91_SMC_WSEN
 113                                 | AT91_SMC_NWS_(15));
 114
 115         at91_set_A_periph(AT91_PIN_PC6, 1);
 116
 117         at91_set_gpio_input(AT91_PIN_PA23, 0);
 118         at91_set_deglitch(AT91_PIN_PA23, 1);
 119
 120 /* Initialization of the Static Memory Controller for Chip Select 3 */
 121         at91_ramc_write(0, AT91_SMC_CSR(3),
 122                 AT91_SMC_DBW_16  |      /* 16 bit */
 123                 AT91_SMC_WSEN    |
 124                 AT91_SMC_NWS_(5) |      /* wait states */
 125                 AT91_SMC_TDF_(1)        /* float time */
 126         );
 127
 128         at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
 129 }
 130
 131 MACHINE_START(ECO920, "eco920")
 132         /* Maintainer: Sascha Hauer */
 133         .timer          = &at91rm9200_timer,
 134         .map_io         = at91_map_io,
 135         .init_early     = eco920_init_early,
 136         .init_irq       = at91_init_irq_default,
 137         .init_machine   = eco920_board_init,
 138 MACHINE_END