2 Advanced Linux Sound Architecture - Driver
3 ==========================================
10 To enable ALSA support you need at least to build the kernel with
11 primary sound card support (CONFIG_SOUND). Since ALSA can emulate OSS,
12 you don't have to choose any of the OSS modules.
14 Enable "OSS API emulation" (CONFIG_SND_OSSEMUL) and both OSS mixer and
15 PCM supports if you want to run OSS applications with ALSA.
17 If you want to support the WaveTable functionality on cards such as
18 SB Live! then you need to enable "Sequencer support"
19 (CONFIG_SND_SEQUENCER).
21 To make ALSA debug messages more verbose, enable the "Verbose printk"
22 and "Debug" options. To check for memory leaks, turn on "Debug memory"
23 too. "Debug detection" will add checks for the detection of cards.
25 Please note that all the ALSA ISA drivers support the Linux isapnp API
26 (if the card supports ISA PnP). You don't need to configure the cards
33 This depends on your distribution, but normally you use the /dev/MAKEDEV
34 script to create the necessary device nodes. On some systems you use a
35 script named 'snddevices'.
41 The user can load modules with options. If the module supports more than
42 one card and you have more than one card of the same type then you can
43 specify multiple values for the option separated by commas.
45 Prior to version 0.9.0rc4 options had a 'snd_' prefix. This was removed.
50 The core ALSA module. It is used by all ALSA card drivers.
51 It takes the following options which have global effects.
53 major - major number for sound driver
56 - limiting card index for auto-loading (1-8)
58 - For auto-loading more than one card, specify this
59 option together with snd-card-X aliases.
61 - permission mask for dynamic sound device filesystem
62 - This is available only when DEVFS is enabled
64 - E.g.: device_mode=0660
70 The PCM OSS emulation module.
71 This module takes options which change the mapping of devices.
73 dsp_map - PCM device number maps assigned to the 1st OSS device.
75 adsp_map - PCM device number maps assigned to the 2st OSS device.
78 - Don't block opening busy PCM devices.
80 For example, when dsp_map=2, /dev/dsp will be mapped to PCM #2 of
81 the card #0. Similarly, when adsp_map=0, /dev/adsp will be mapped
82 to PCM #0 of the card #0.
83 For changing the second or later card, specify the option with
84 commas, such like "dsp_map=0,1".
86 nonblock_open option is used to change the behavior of the PCM
87 regarding opening the device. When this option is non-zero,
88 opening a busy OSS PCM device won't be blocked but return
89 immediately with EAGAIN (just like O_NONBLOCK flag).
94 This module takes options which change the mapping of devices.
95 similar to those of the snd-pcm-oss module.
97 midi_map - MIDI device number maps assigned to the 1st OSS device.
99 amidi_map - MIDI device number maps assigned to the 2st OSS device.
102 Common parameters for top sound card modules
103 --------------------------------------------
105 Each of top level sound card module takes the following options.
107 index - index (slot #) of sound card
108 - Values: 0 through 7 or negative
109 - If nonnegative, assign that index number
110 - if negative, interpret as a bitmask of permissible
111 indices; the first free permitted index is assigned
113 id - card ID (identifier or name)
114 - Can be up to 15 characters long
115 - Default: the card type
116 - A directory by this name is created under /proc/asound/
117 containing information about the card
118 - This ID can be used instead of the index number in
121 - Default: enabled, for PCI and ISA PnP cards
126 Module for sound cards based on Analog Devices AD1816A/AD1815 ISA chips.
128 port - port # for AD1816A chip (PnP setup)
129 mpu_port - port # for MPU-401 UART (PnP setup)
130 fm_port - port # for OPL3 (PnP setup)
131 irq - IRQ # for AD1816A chip (PnP setup)
132 mpu_irq - IRQ # for MPU-401 UART (PnP setup)
133 dma1 - first DMA # for AD1816A chip (PnP setup)
134 dma2 - second DMA # for AD1816A chip (PnP setup)
136 Module supports up to 8 cards, autoprobe and PnP.
141 Module for sound cards based on AD1848/AD1847/CS4248 ISA chips.
143 port - port # for AD1848 chip
144 irq - IRQ # for AD1848 chip
145 dma1 - DMA # for AD1848 chip (0,1,3)
147 Module supports up to 8 cards. This module does not support autoprobe
148 thus main port must be specified!!! Other ports are optional.
153 Module for ALi M5451 PCI chip.
155 pcm_channels - Number of hardware channels assigned for PCM
156 spdif - Support SPDIF I/O
159 Module supports autoprobe and multiple chips (max 8).
161 The power-management is supported.
166 Module for sound cards based on Avance Logic ALS100/ALS120 ISA chips.
168 port - port # for ALS100 (SB16) chip (PnP setup)
169 irq - IRQ # for ALS100 (SB16) chip (PnP setup)
170 dma8 - 8-bit DMA # for ALS100 (SB16) chip (PnP setup)
171 dma16 - 16-bit DMA # for ALS100 (SB16) chip (PnP setup)
172 mpu_port - port # for MPU-401 UART (PnP setup)
173 mpu_irq - IRQ # for MPU-401 (PnP setup)
174 fm_port - port # for OPL3 FM (PnP setup)
176 Module supports up to 8 cards, autoprobe and PnP.
181 Module for sound cards based on Avance Logic ALS4000 PCI chip.
183 joystick_port - port # for legacy joystick support.
184 0 = disabled (default), 1 = auto-detect
186 Module supports up to 8 cards, autoprobe and PnP.
191 Module for ATI IXP 150/200/250 AC97 controllers.
193 ac97_clock - AC'97 clock (defalut = 48000)
194 ac97_quirk - AC'97 workaround for strange hardware
195 See the description of intel8x0 module for details.
196 spdif_aclink - S/PDIF transfer over AC-link (default = 1)
198 This module supports up to 8 cards and autoprobe.
200 Module snd-atiixp-modem
201 -----------------------
203 Module for ATI IXP 150/200/250 AC97 modem controllers.
205 Module supports up to 8 cards.
207 Note: The default index value of this module is -2, i.e. the first
210 Module snd-au8810, snd-au8820, snd-au8830
211 -----------------------------------------
213 Module for Aureal Vortex, Vortex2 and Advantage device.
215 pcifix - Control PCI workarounds
216 0 = Disable all workarounds
217 1 = Force the PCI latency of the Aureal card to 0xff
218 2 = Force the Extend PCI#2 Internal Master for Efficient
219 Handling of Dummy Requests on the VIA KT133 AGP Bridge
220 3 = Force both settings
221 255 = Autodetect what is required (default)
223 This module supports all ADB PCM channels, ac97 mixer, SPDIF, hardware
224 EQ, mpu401, gameport. A3D and wavetable support are still in development.
225 Development and reverse engineering work is being coordinated at
226 http://savannah.nongnu.org/projects/openvortex/
227 SPDIF output has a copy of the AC97 codec output, unless you use the
228 "spdif" pcm device, which allows raw data passthru.
229 The hardware EQ hardware and SPDIF is only present in the Vortex2 and
232 Note: Some ALSA mixer applicactions don't handle the SPDIF samplerate
233 control correctly. If you have problems regarding this, try
234 another ALSA compliant mixer (alsamixer works).
239 Module for sound cards based on Aztech System AZT2320 ISA chip (PnP only).
241 port - port # for AZT2320 chip (PnP setup)
242 wss_port - port # for WSS (PnP setup)
243 mpu_port - port # for MPU-401 UART (PnP setup)
244 fm_port - FM port # for AZT2320 chip (PnP setup)
245 irq - IRQ # for AZT2320 (WSS) chip (PnP setup)
246 mpu_irq - IRQ # for MPU-401 UART (PnP setup)
247 dma1 - 1st DMA # for AZT2320 (WSS) chip (PnP setup)
248 dma2 - 2nd DMA # for AZT2320 (WSS) chip (PnP setup)
250 Module supports up to 8 cards, PnP and autoprobe.
255 Module for sound cards based on Aztech AZF3328 PCI chip.
257 joystick - Enable joystick (default off)
259 Module supports up to 8 cards.
264 Module for video cards based on Bt87x chips.
266 digital_rate - Override the default digital rate (Hz)
267 load_all - Load the driver even if the card model isn't known
269 Module supports up to 8 cards.
271 Note: The default index value of this module is -2, i.e. the first
277 Module for Creative Audigy LS and SB Live 24bit
279 Module supports up to 8 cards.
285 Module for sound cards based on C-Media CMI8330 ISA chips.
287 wssport - port # for CMI8330 chip (WSS)
288 wssirq - IRQ # for CMI8330 chip (WSS)
289 wssdma - first DMA # for CMI8330 chip (WSS)
290 sbport - port # for CMI8330 chip (SB16)
291 sbirq - IRQ # for CMI8330 chip (SB16)
292 sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
293 sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
295 Module supports up to 8 cards and autoprobe.
300 Module for C-Media CMI8338 and 8738 PCI sound cards.
302 mpu_port - 0x300,0x310,0x320,0x330, 0 = disable (default)
303 fm_port - 0x388 (default), 0 = disable (default)
304 soft_ac3 - Sofware-conversion of raw SPDIF packets (model 033 only)
306 joystick_port - Joystick port address (0 = disable, 1 = auto-detect)
308 Module supports autoprobe and multiple chips (max 8).
313 Module for sound cards based on CS4231 ISA chips.
315 port - port # for CS4231 chip
316 mpu_port - port # for MPU-401 UART (optional), -1 = disable
317 irq - IRQ # for CS4231 chip
318 mpu_irq - IRQ # for MPU-401 UART
319 dma1 - first DMA # for CS4231 chip
320 dma2 - second DMA # for CS4231 chip
322 Module supports up to 8 cards. This module does not support autoprobe
323 thus main port must be specified!!! Other ports are optional.
325 The power-management is supported.
330 Module for sound cards based on CS4232/CS4232A ISA chips.
332 port - port # for CS4232 chip (PnP setup - 0x534)
333 cport - control port # for CS4232 chip (PnP setup - 0x120,0x210,0xf00)
334 mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
335 fm_port - FM port # for CS4232 chip (PnP setup - 0x388), -1 = disable
336 irq - IRQ # for CS4232 chip (5,7,9,11,12,15)
337 mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
338 dma1 - first DMA # for CS4232 chip (0,1,3)
339 dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
340 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
342 Module supports up to 8 cards. This module does not support autoprobe
343 thus main port must be specified!!! Other ports are optional.
345 The power-management is supported.
350 Module for sound cards based on CS4235/CS4236/CS4236B/CS4237B/
351 CS4238B/CS4239 ISA chips.
353 port - port # for CS4236 chip (PnP setup - 0x534)
354 cport - control port # for CS4236 chip (PnP setup - 0x120,0x210,0xf00)
355 mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
356 fm_port - FM port # for CS4236 chip (PnP setup - 0x388), -1 = disable
357 irq - IRQ # for CS4236 chip (5,7,9,11,12,15)
358 mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
359 dma1 - first DMA # for CS4236 chip (0,1,3)
360 dma2 - second DMA # for CS4236 chip (0,1,3), -1 = disable
361 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
363 Module supports up to 8 cards. This module does not support autoprobe
364 (if ISA PnP is not used) thus main port and control port must be
365 specified!!! Other ports are optional.
367 The power-management is supported.
372 Module for Cirrus Logic CS4281 soundchip.
374 dual_codec - Secondary codec ID (0 = disable, default)
376 Module supports up to 8 cards.
378 The power-management is supported.
383 Module for PCI sound cards based on CS4610/CS4612/CS4614/CS4615/CS4622/
384 CS4624/CS4630/CS4280 PCI chips.
386 external_amp - Force to enable external amplifer.
387 thinkpad - Force to enable Thinkpad's CLKRUN control.
388 mmap_valid - Support OSS mmap mode (default = 0).
390 Module supports up to 8 cards and autoprobe.
391 Usually external amp and CLKRUN controls are detected automatically
392 from PCI sub vendor/device ids. If they don't work, give the options
395 The power-management is supported.
400 Module for Diamond Technologies DT-019X / Avance Logic ALS-007 (PnP
403 port - Port # (PnP setup)
404 mpu_port - Port # for MPU-401 (PnP setup)
405 fm_port - Port # for FM OPL-3 (PnP setup)
406 irq - IRQ # (PnP setup)
407 mpu_irq - IRQ # for MPU-401 (PnP setup)
408 dma8 - DMA # (PnP setup)
410 Module supports up to 8 cards. This module is enabled only with
416 Module for the dummy sound card. This "card" doesn't do any output
417 or input, but you may use this module for any application which
418 requires a sound card (like RealPlayer).
423 Module for EMU10K1/EMU10k2 based PCI sound cards.
424 * Sound Blaster Live!
425 * Sound Blaster PCI 512
426 * Emu APS (partially supported)
427 * Sound Blaster Audigy
429 extin - bitmap of available external inputs for FX8010 (see bellow)
430 extout - bitmap of available external outputs for FX8010 (see bellow)
431 seq_ports - allocated sequencer ports (4 by default)
432 max_synth_voices - limit of voices used for wavetable (64 by default)
433 max_buffer_size - specifies the maximum size of wavetable/pcm buffers
434 given in MB unit. Default value is 128.
435 enable_ir - enable IR
437 Module supports up to 8 cards and autoprobe.
439 Input & Output configurations [extin/extout]
440 * Creative Card wo/Digital out [0x0003/0x1f03]
441 * Creative Card w/Digital out [0x0003/0x1f0f]
442 * Creative Card w/Digital CD in [0x000f/0x1f0f]
443 * Creative Card wo/Digital out + LiveDrive [0x3fc3/0x1fc3]
444 * Creative Card w/Digital out + LiveDrive [0x3fc3/0x1fcf]
445 * Creative Card w/Digital CD in + LiveDrive [0x3fcf/0x1fcf]
446 * Creative Card wo/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
447 * Creative Card w/Digital out + Digital I/O 2 [0x0fc3/0x1f0f]
448 * Creative Card w/Digital CD in + Digital I/O 2 [0x0fcf/0x1f0f]
449 * Creative Card 5.1/w Digital out + LiveDrive [0x3fc3/0x1fff]
450 * Creative Card 5.1 (c) 2003 [0x3fc3/0x7cff]
451 * Creative Card all ins and outs [0x3fff/0x7fff]
456 Module for Creative Emu10k1X (SB Live Dell OEM version)
458 Module supports up to 8 cards.
463 Module for Ensoniq AudioPCI ES1370 PCI sound cards.
464 * SoundBlaster PCI 64
465 * SoundBlaster PCI 128
467 joystick - Enable joystick (default off)
469 Module supports up to 8 cards and autoprobe.
474 Module for Ensoniq AudioPCI ES1371 PCI sound cards.
475 * SoundBlaster PCI 64
476 * SoundBlaster PCI 128
477 * SoundBlaster Vibra PCI
479 joystick_port - port # for joystick (0x200,0x208,0x210,0x218),
480 0 = disable (default), 1 = auto-detect
482 Module supports up to 8 cards and autoprobe.
487 Module for sound cards based on ESS ES968 chip (PnP only).
489 port - port # for ES968 (SB8) chip (PnP setup)
490 irq - IRQ # for ES968 (SB8) chip (PnP setup)
491 dma1 - DMA # for ES968 (SB8) chip (PnP setup)
493 Module supports up to 8 cards, PnP and autoprobe.
498 Module for ESS AudioDrive ES-1688 and ES-688 sound cards.
500 port - port # for ES-1688 chip (0x220,0x240,0x260)
501 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
502 irq - IRQ # for ES-1688 chip (5,7,9,10)
503 mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
504 dma8 - DMA # for ES-1688 chip (0,1,3)
506 Module supports up to 8 cards and autoprobe (without MPU-401 port).
511 Module for ESS AudioDrive ES-18xx sound cards.
513 port - port # for ES-18xx chip (0x220,0x240,0x260)
514 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
515 fm_port - port # for FM (optional, not used)
516 irq - IRQ # for ES-18xx chip (5,7,9,10)
517 dma1 - first DMA # for ES-18xx chip (0,1,3)
518 dma2 - first DMA # for ES-18xx chip (0,1,3)
519 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
521 Module supports up to 8 cards ISA PnP and autoprobe (without MPU-401 port
522 if native ISA PnP routines are not used).
523 When dma2 is equal with dma1, the driver works as half-duplex.
525 The power-management is supported.
530 Module for sound cards based on ESS Solo-1 (ES1938,ES1946) chips.
532 Module supports up to 8 cards and autoprobe.
537 Module for sound cards based on ESS Maestro-1/2/2E (ES1968/ES1978) chips.
539 total_bufsize - total buffer size in kB (1-4096kB)
540 pcm_substreams_p - playback channels (1-8, default=2)
541 pcm_substreams_c - capture channels (1-8, default=0)
542 clock - clock (0 = auto-detection)
543 use_pm - support the power-management (0 = off, 1 = on,
545 enable_mpu - enable MPU401 (0 = off, 1 = on, 2 = auto (default))
546 joystick - enable joystick (default off)
548 Module supports up to 8 cards and autoprobe.
550 The power-management is supported.
555 Module for ForteMedia FM801 based PCI sound cards.
557 tea575x_tuner - Enable TEA575x tuner
558 - 1 = MediaForte 256-PCS
559 - 2 = MediaForte 256-PCPR
560 - 3 = MediaForte 64-PCR
561 - High 16-bits are video (radio) device number + 1
562 - example: 0x10002 (MediaForte 256-PCPR, device 1)
564 Module supports up to 8 cards and autoprobe.
566 Module snd-gusclassic
567 ---------------------
569 Module for Gravis UltraSound Classic sound card.
571 port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
572 irq - IRQ # for GF1 chip (3,5,9,11,12,15)
573 dma1 - DMA # for GF1 chip (1,3,5,6,7)
574 dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable)
575 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
576 voices - GF1 voices limit (14-32)
577 pcm_voices - reserved PCM voices
579 Module supports up to 8 cards and autoprobe.
581 Module snd-gusextreme
582 ---------------------
584 Module for Gravis UltraSound Extreme (Synergy ViperMax) sound card.
586 port - port # for ES-1688 chip (0x220,0x230,0x240,0x250,0x260)
587 gf1_port - port # for GF1 chip (0x210,0x220,0x230,0x240,0x250,0x260,0x270)
588 mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable
589 irq - IRQ # for ES-1688 chip (5,7,9,10)
590 gf1_irq - IRQ # for GF1 chip (3,5,9,11,12,15)
591 mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
592 dma8 - DMA # for ES-1688 chip (0,1,3)
593 dma1 - DMA # for GF1 chip (1,3,5,6,7)
594 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
595 voices - GF1 voices limit (14-32)
596 pcm_voices - reserved PCM voices
598 Module supports up to 8 cards and autoprobe (without MPU-401 port).
603 Module for Gravis UltraSound MAX sound card.
605 port - port # for GF1 chip (0x220,0x230,0x240,0x250,0x260)
606 irq - IRQ # for GF1 chip (3,5,9,11,12,15)
607 dma1 - DMA # for GF1 chip (1,3,5,6,7)
608 dma2 - DMA # for GF1 chip (1,3,5,6,7,-1=disable)
609 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
610 voices - GF1 voices limit (14-32)
611 pcm_voices - reserved PCM voices
613 Module supports up to 8 cards and autoprobe.
618 Module for Intel HD Audio (ICH6, ICH6M, ICH7), ATI SB450,
621 model - force the model name
622 position_fix - Fix DMA pointer (0 = FIFO size, 1 = none, 2 = POSBUF)
624 Module supports up to 8 cards.
626 Each codec may have a model table for different configurations.
627 If your machine isn't listed there, the default (usually minimal)
628 configuration is set up. You can pass "model=<name>" option to
629 specify a certain model in such a case. There are different
630 models depending on the codec chip.
632 Model name Description
633 ---------- -----------
635 3stack 3-jack in back and a headphone out
636 3stack-digout 3-jack in back, a HP out and a SPDIF out
637 5stack 5-jack in back, 2-jack in front
638 5stack-digout 5-jack in back, 2-jack in front, a SPDIF out
639 6stack 6-jack in back, 2-jack in front
640 6stack-digout 6-jack with a SPDIF out
642 z71v 3-jack (HP shared SPDIF)
646 test for testing/debugging purpose, almost all controls can be
647 adjusted. Appearing only when compiled with
651 minimal 3-jack in back
652 min_fp 3-jack in back, 2-jack in front
653 full 6-jack in back, 2-jack in front
654 full_dig 6-jack in back, 2-jack in front, SPDIF I/O
655 allout 5-jack in back, 2-jack in front, SPDIF out
656 auto auto-config reading BIOS (default)
658 Note 2: If you get click noises on output, try the module option
659 position_fix=1 or 2. position_fix=1 will use the SD_LPIB
660 register value without FIFO size correction as the current
661 DMA pointer. position_fix=2 will make the driver to use
662 the position buffer instead of reading SD_LPIB register.
663 (Usually SD_LPLIB register is more accurate than the
669 Module for RME Hammerfall DSP audio interface(s)
671 Module supports up to 8 cards.
673 Note: The firmware data can be automatically loaded via hotplug
674 when CONFIG_FW_LOADER is set. Otherwise, you need to load
675 the firmware via hdsploader utility included in alsa-tools
677 The firmware data is found in alsa-firmware package.
679 Note: snd-page-alloc module does the job which snd-hammerfall-mem
680 module did formerly. It will allocate the buffers in advance
681 when any HDSP cards are found. To make the buffer
682 allocation sure, load snd-page-alloc module in the early
683 stage of boot sequence. See "Early Buffer Allocation"
689 Module for RME HDSP MADI board.
691 precise_ptr - Enable precise pointer, or disable.
692 line_outs_monitor - Send playback streams to analog outs by default.
693 enable_monitor - Enable Analog Out on Channel 63/64 by default.
695 See hdspm.txt for details.
700 Module for Envy24 (ICE1712) based PCI sound cards.
701 * MidiMan M Audio Delta 1010
702 * MidiMan M Audio Delta 1010LT
703 * MidiMan M Audio Delta DiO 2496
704 * MidiMan M Audio Delta 66
705 * MidiMan M Audio Delta 44
706 * MidiMan M Audio Delta 410
707 * MidiMan M Audio Audiophile 2496
713 * Hoontech SoundTrack DSP 24
714 * Hoontech SoundTrack DSP 24 Value
715 * Hoontech SoundTrack DSP 24 Media 7.1
716 * Event Electronics, EZ8
718 * Lionstracs, Mediastaton
720 model - Use the given board model, one of the following:
721 delta1010, dio2496, delta66, delta44, audiophile, delta410,
722 delta1010lt, vx442, ewx2496, ews88mt, ews88mt_new, ews88d,
723 dmx6fire, dsp24, dsp24_value, dsp24_71, ez8,
724 phase88, mediastation
725 omni - Omni I/O support for MidiMan M-Audio Delta44/66
726 cs8427_timeout - reset timeout for the CS8427 chip (S/PDIF transciever)
727 in msec resolution, default value is 500 (0.5 sec)
729 Module supports up to 8 cards and autoprobe. Note: The consumer part
730 is not used with all Envy24 based cards (for example in the MidiMan Delta
733 Note: The supported board is detected by reading EEPROM or PCI
734 SSID (if EEPROM isn't available). You can override the
735 model by passing "model" module option in case that the
736 driver isn't configured properly or you want to try another
742 Module for Envy24HT (VT/ICE1724), Envy24PT (VT1720) based PCI sound cards.
743 * MidiMan M Audio Revolution 7.1
745 * TerraTec Aureon 5.1 Sky
746 * TerraTec Aureon 7.1 Space
747 * TerraTec Aureon 7.1 Universe
750 * AudioTrak Prodigy 7.1
751 * AudioTrak Prodigy 192
753 * Albatron K8X800 Pro II
760 model - Use the given board model, one of the following:
761 revo71, amp2000, prodigy71, prodigy192, aureon51,
762 aureon71, universe, k8x800, phase22, phase28, ms300,
765 Module supports up to 8 cards and autoprobe.
767 Note: The supported board is detected by reading EEPROM or PCI
768 SSID (if EEPROM isn't available). You can override the
769 model by passing "model" module option in case that the
770 driver isn't configured properly or you want to try another
776 Module for AC'97 motherboards from Intel and compatibles.
777 * Intel i810/810E, i815, i820, i830, i84x, MX440
779 * NVidia NForce, NForce2
780 * AMD AMD768, AMD8111
783 ac97_clock - AC'97 codec clock base (0 = auto-detect)
784 ac97_quirk - AC'97 workaround for strange hardware
785 The following strings are accepted:
786 default = don't override the default setting
787 disable = disable the quirk
788 hp_only = use headphone control as master
789 swap_hp = swap headphone and master controls
790 swap_surround = swap master and surround controls
791 ad_sharing = for AD1985, turn on OMS bit and use headphone
792 alc_jack = for ALC65x, turn on the jack sense mode
793 inv_eapd = inverted EAPD implementation
794 mute_led = bind EAPD bit for turning on/off mute LED
795 For backward compatibility, the corresponding integer
796 value -1, 0, ... are accepted, too.
797 buggy_irq - Enable workaround for buggy interrupts on some
798 motherboards (default off)
800 Module supports autoprobe and multiple bus-master chips (max 8).
802 Note: the latest driver supports auto-detection of chip clock.
803 if you still encounter too fast playback, specify the clock
804 explicitly via the module option "ac97_clock=41194".
806 Joystick/MIDI ports are not supported by this driver. If your
807 motherboard has these devices, use the ns558 or snd-mpu401
808 modules, respectively.
810 The ac97_quirk option is used to enable/override the workaround
811 for specific devices. Some hardware have swapped output pins
812 between Master and Headphone, or Surround. The driver provides
813 the auto-detection of known problematic devices, but some might
814 be unknown or wrongly detected. In such a case, pass the proper
815 value with this option.
817 The power-management is supported.
822 Module for Intel ICH (i8x0) chipset MC97 modems.
824 ac97_clock - AC'97 codec clock base (0 = auto-detect)
826 This module supports up to 8 cards and autoprobe.
828 Note: The default index value of this module is -2, i.e. the first
834 Module for Gravis UltraSound PnP, Dynasonic 3-D/Pro, STB Sound Rage 32
835 and other sound cards based on AMD InterWave (tm) chip.
837 port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
838 irq - IRQ # for InterWave chip (3,5,9,11,12,15)
839 dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
840 dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
841 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
842 midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
843 pcm_voices - reserved PCM voices for the synthesizer (default 2)
844 effect - 1 = InterWave effects enable (default 0);
847 Module supports up to 8 cards, autoprobe and ISA PnP.
849 Module snd-interwave-stb
850 ------------------------
852 Module for UltraSound 32-Pro (sound card from STB used by Compaq)
853 and other sound cards based on AMD InterWave (tm) chip with TEA6330T
854 circuit for extended control of bass, treble and master volume.
856 port - port # for InterWave chip (0x210,0x220,0x230,0x240,0x250,0x260)
857 port_tc - tone control (i2c bus) port # for TEA6330T chip (0x350,0x360,0x370,0x380)
858 irq - IRQ # for InterWave chip (3,5,9,11,12,15)
859 dma1 - DMA # for InterWave chip (0,1,3,5,6,7)
860 dma2 - DMA # for InterWave chip (0,1,3,5,6,7,-1=disable)
861 joystick_dac - 0 to 31, (0.59V-4.52V or 0.389V-2.98V)
862 midi - 1 = MIDI UART enable, 0 = MIDI UART disable (default)
863 pcm_voices - reserved PCM voices for the synthesizer (default 2)
864 effect - 1 = InterWave effects enable (default 0);
867 Module supports up to 8 cards, autoprobe and ISA PnP.
872 Module for Korg 1212 IO PCI card
874 Module supports up to 8 cards.
879 Module for Allegro/Maestro3 chips
881 external_amp - enable external amp (enabled by default)
882 amp_gpio - GPIO pin number for external amp (0-15) or
883 -1 for default pin (8 for allegro, 1 for
886 Module supports autoprobe and multiple chips (max 8).
888 Note: the binding of amplifier is dependent on hardware.
889 If there is no sound even though all channels are unmuted, try to
890 specify other gpio connection via amp_gpio option.
891 For example, a Panasonic notebook might need "amp_gpio=0x0d"
894 The power-management is supported.
899 Module for Digigram miXart8 sound cards.
901 Module supports multiple cards.
902 Note: One miXart8 board will be represented as 4 alsa cards.
903 See MIXART.txt for details.
905 When the driver is compiled as a module and the hotplug firmware
906 is supported, the firmware data is loaded via hotplug automatically.
907 Install the necessary firmware files in alsa-firmware package.
908 When no hotplug fw loader is available, you need to load the
909 firmware via mixartloader utility in alsa-tools package.
914 Module for MPU-401 UART devices.
916 port - port number or -1 (disable)
917 irq - IRQ number or -1 (disable)
918 pnp - PnP detection - 0 = disable, 1 = enable (default)
920 Module supports multiple devices (max 8) and PnP.
925 Module for MOTU MidiTimePiece AV multiport MIDI (on the parallel
928 port - I/O port # for MTPAV (0x378,0x278, default=0x378)
929 irq - IRQ # for MTPAV (7,5, default=7)
930 hwports - number of supported hardware ports, default=8.
932 Module supports only 1 card. This module has no enable option.
937 Module for NeoMagic NM256AV/ZX chips
939 playback_bufsize - max playback frame size in kB (4-128kB)
940 capture_bufsize - max capture frame size in kB (4-128kB)
941 force_ac97 - 0 or 1 (disabled by default)
942 buffer_top - specify buffer top address
943 use_cache - 0 or 1 (disabled by default)
944 vaio_hack - alias buffer_top=0x25a800
945 reset_workaround - enable AC97 RESET workaround for some laptops
947 Module supports autoprobe and multiple chips (max 8).
949 The power-management is supported.
951 Note: on some notebooks the buffer address cannot be detected
952 automatically, or causes hang-up during initialization.
953 In such a case, specify the buffer top address explicity via
956 Sony F250: buffer_top=0x25a800
957 Sony F270: buffer_top=0x272800
958 The driver supports only ac97 codec. It's possible to force
959 to initialize/use ac97 although it's not detected. In such a
960 case, use force_ac97=1 option - but *NO* guarantee whether it
963 Note: The NM256 chip can be linked internally with non-AC97
964 codecs. This driver supports only the AC97 codec, and won't work
965 with machines with other (most likely CS423x or OPL3SAx) chips,
966 even though the device is detected in lspci. In such a case, try
967 other drivers, e.g. snd-cs4232 or snd-opl3sa2. Some has ISA-PnP
968 but some doesn't have ISA PnP. You'll need to speicfy isapnp=0
969 and proper hardware parameters in the case without ISA PnP.
971 Note: some laptops need a workaround for AC97 RESET. For the
972 known hardware like Dell Latitude LS and Sony PCG-F305, this
973 workaround is enabled automatically. For other laptops with a
974 hard freeze, you can try reset_workaround=1 option.
976 Note: This driver is really crappy. It's a porting from the
977 OSS driver, which is a result of black-magic reverse engineering.
978 The detection of codec will fail if the driver is loaded *after*
979 X-server as described above. You might be able to force to load
980 the module, but it may result in hang-up. Hence, make sure that
981 you load this module *before* X if you encounter this kind of
987 Module for Yamaha OPL3-SA2/SA3 sound cards.
989 port - control port # for OPL3-SA chip (0x370)
990 sb_port - SB port # for OPL3-SA chip (0x220,0x240)
991 wss_port - WSS port # for OPL3-SA chip (0x530,0xe80,0xf40,0x604)
992 midi_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
993 fm_port - FM port # for OPL3-SA chip (0x388), -1 = disable
994 irq - IRQ # for OPL3-SA chip (5,7,9,10)
995 dma1 - first DMA # for Yamaha OPL3-SA chip (0,1,3)
996 dma2 - second DMA # for Yamaha OPL3-SA chip (0,1,3), -1 = disable
997 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
999 Module supports up to 8 cards and ISA PnP. This module does not support
1000 autoprobe (if ISA PnP is not used) thus all ports must be specified!!!
1002 The power-management is supported.
1004 Module snd-opti92x-ad1848
1005 -------------------------
1007 Module for sound cards based on OPTi 82c92x and Analog Devices AD1848 chips.
1008 Module works with OAK Mozart cards as well.
1010 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1011 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1012 fm_port - port # for OPL3 device (0x388)
1013 irq - IRQ # for WSS chip (5,7,9,10,11)
1014 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1015 dma1 - first DMA # for WSS chip (0,1,3)
1017 This module supports only one card, autoprobe and PnP.
1019 Module snd-opti92x-cs4231
1020 -------------------------
1022 Module for sound cards based on OPTi 82c92x and Crystal CS4231 chips.
1024 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1025 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1026 fm_port - port # for OPL3 device (0x388)
1027 irq - IRQ # for WSS chip (5,7,9,10,11)
1028 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1029 dma1 - first DMA # for WSS chip (0,1,3)
1030 dma2 - second DMA # for WSS chip (0,1,3)
1032 This module supports only one card, autoprobe and PnP.
1037 Module for sound cards based on OPTi 82c93x chips.
1039 port - port # for WSS chip (0x530,0xe80,0xf40,0x604)
1040 mpu_port - port # for MPU-401 UART (0x300,0x310,0x320,0x330)
1041 fm_port - port # for OPL3 device (0x388)
1042 irq - IRQ # for WSS chip (5,7,9,10,11)
1043 mpu_irq - IRQ # for MPU-401 UART (5,7,9,10)
1044 dma1 - first DMA # for WSS chip (0,1,3)
1045 dma2 - second DMA # for WSS chip (0,1,3)
1047 This module supports only one card, autoprobe and PnP.
1049 Module snd-powermac (on ppc only)
1050 ---------------------------------
1052 Module for PowerMac, iMac and iBook on-board soundchips
1054 enable_beep - enable beep using PCM (enabled as default)
1056 Module supports autoprobe a chip.
1058 Note: the driver may have problems regarding endianess.
1060 The power-management is supported.
1065 Module for RME Digi32, Digi32 Pro and Digi32/8 (Sek'd Prodif32,
1066 Prodif96 and Prodif Gold) sound cards.
1068 Module supports up to 8 cards.
1073 Module for RME Digi96, Digi96/8 and Digi96/8 PRO/PAD/PST sound cards.
1075 Module supports up to 8 cards.
1080 Module for RME Digi9652 (Hammerfall, Hammerfall-Light) sound cards.
1082 precise_ptr - Enable precise pointer (doesn't work reliably).
1085 Module supports up to 8 cards.
1087 Note: snd-page-alloc module does the job which snd-hammerfall-mem
1088 module did formerly. It will allocate the buffers in advance
1089 when any RME9652 cards are found. To make the buffer
1090 allocation sure, load snd-page-alloc module in the early
1091 stage of boot sequence. See "Early Buffer Allocation"
1094 Module snd-sa11xx-uda1341 (on arm only)
1095 ---------------------------------------
1097 Module for Philips UDA1341TS on Compaq iPAQ H3600 sound card.
1099 Module supports only one card.
1100 Module has no enable and index options.
1105 Module for 8-bit SoundBlaster cards: SoundBlaster 1.0,
1109 port - port # for SB DSP chip (0x220,0x240,0x260)
1110 irq - IRQ # for SB DSP chip (5,7,9,10)
1111 dma8 - DMA # for SB DSP chip (1,3)
1113 Module supports up to 8 cards and autoprobe.
1115 Module snd-sb16 and snd-sbawe
1116 -----------------------------
1118 Module for 16-bit SoundBlaster cards: SoundBlaster 16 (PnP),
1119 SoundBlaster AWE 32 (PnP),
1120 SoundBlaster AWE 64 PnP
1122 port - port # for SB DSP 4.x chip (0x220,0x240,0x260)
1123 mpu_port - port # for MPU-401 UART (0x300,0x330), -1 = disable
1124 awe_port - base port # for EMU8000 synthesizer (0x620,0x640,0x660)
1125 (snd-sbawe module only)
1126 irq - IRQ # for SB DSP 4.x chip (5,7,9,10)
1127 dma8 - 8-bit DMA # for SB DSP 4.x chip (0,1,3)
1128 dma16 - 16-bit DMA # for SB DSP 4.x chip (5,6,7)
1129 mic_agc - Mic Auto-Gain-Control - 0 = disable, 1 = enable (default)
1130 csp - ASP/CSP chip support - 0 = disable (default), 1 = enable
1131 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1133 Module supports up to 8 cards, autoprobe and ISA PnP.
1135 Note: To use Vibra16X cards in 16-bit half duplex mode, you must
1136 disable 16bit DMA with dma16 = -1 module parameter.
1137 Also, all Sound Blaster 16 type cards can operate in 16-bit
1138 half duplex mode through 8-bit DMA channel by disabling their
1144 Module for Aztech Sound Galaxy sound card.
1146 sbport - Port # for SB16 interface (0x220,0x240)
1147 wssport - Port # for WSS interface (0x530,0xe80,0xf40,0x604)
1148 irq - IRQ # (7,9,10,11)
1151 Module supports up to 8 cards.
1156 Module for ENSONIQ SoundScape PnP cards.
1158 port - Port # (PnP setup)
1159 irq - IRQ # (PnP setup)
1160 mpu_irq - MPU-401 IRQ # (PnP setup)
1161 dma - DMA # (PnP setup)
1163 Module supports up to 8 cards. ISA PnP must be enabled.
1164 You need sscape_ctl tool in alsa-tools package for loading
1167 Module snd-sun-amd7930 (on sparc only)
1168 --------------------------------------
1170 Module for AMD7930 sound chips found on Sparcs.
1172 Module supports up to 8 cards.
1174 Module snd-sun-cs4231 (on sparc only)
1175 -------------------------------------
1177 Module for CS4231 sound chips found on Sparcs.
1179 Module supports up to 8 cards.
1181 Module snd-wavefront
1182 --------------------
1184 Module for Turtle Beach Maui, Tropez and Tropez+ sound cards.
1186 cs4232_pcm_port - Port # for CS4232 PCM interface.
1187 cs4232_pcm_irq - IRQ # for CS4232 PCM interface (5,7,9,11,12,15).
1188 cs4232_mpu_port - Port # for CS4232 MPU-401 interface.
1189 cs4232_mpu_irq - IRQ # for CS4232 MPU-401 interface (9,11,12,15).
1190 use_cs4232_midi - Use CS4232 MPU-401 interface
1191 (inaccessibly located inside your computer)
1192 ics2115_port - Port # for ICS2115
1193 ics2115_irq - IRQ # for ICS2115
1194 fm_port - FM OPL-3 Port #
1195 dma1 - DMA1 # for CS4232 PCM interface.
1196 dma2 - DMA2 # for CS4232 PCM interface.
1197 isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
1199 Module supports up to 8 cards and ISA PnP.
1201 Module snd-sonicvibes
1202 ---------------------
1204 Module for S3 SonicVibes PCI sound cards.
1205 * PINE Schubert 32 PCI
1207 reverb - Reverb Enable - 1 = enable, 0 = disable (default)
1208 - SoundCard must have onboard SRAM for this.
1209 mge - Mic Gain Enable - 1 = enable, 0 = disable (default)
1211 Module supports up to 8 cards and autoprobe.
1213 Module snd-serial-u16550
1214 ------------------------
1216 Module for UART16550A serial MIDI ports.
1218 port - port # for UART16550A chip
1219 irq - IRQ # for UART16550A chip, -1 = poll mode
1220 speed - speed in bauds (9600,19200,38400,57600,115200)
1222 base - base for divisor in bauds (57600,115200,230400,460800)
1224 outs - number of MIDI ports in a serial port (1-4)
1226 adaptor - Type of adaptor.
1227 0 = Soundcanvas, 1 = MS-124T, 2 = MS-124W S/A,
1228 3 = MS-124W M/B, 4 = Generic
1230 Module supports up to 8 cards. This module does not support autoprobe
1231 thus the main port must be specified!!! Other options are optional.
1236 Module for Trident 4DWave DX/NX sound cards.
1237 * Best Union Miss Melody 4DWave PCI
1239 * Warpspeed ONSpeed 4DWave PCI
1242 * CHIC True Sound 4Dwave
1243 * Shark Predator4D-PCI
1244 * Jaton SonicWave 4D
1246 pcm_channels - max channels (voices) reserved for PCM
1247 wavetable_size - max wavetable size in kB (4-?kb)
1249 Module supports up to 8 cards and autoprobe.
1251 The power-management is supported.
1253 Module snd-usb-audio
1254 --------------------
1256 Module for USB audio and USB MIDI devices.
1258 vid - Vendor ID for the device (optional)
1259 pid - Product ID for the device (optional)
1261 This module supports up to 8 cards, autoprobe and hotplugging.
1263 Module snd-usb-usx2y
1264 --------------------
1266 Module for Tascam USB US-122, US-224 and US-428 devices.
1268 This module supports up to 8 cards, autoprobe and hotplugging.
1270 Note: you need to load the firmware via usx2yloader utility included
1271 in alsa-tools and alsa-firmware packages.
1276 Module for AC'97 motherboards based on VIA 82C686A/686B, 8233,
1277 8233A, 8233C, 8235, 8237 (south) bridge.
1279 mpu_port - 0x300,0x310,0x320,0x330, otherwise obtain BIOS setup
1281 joystick - Enable joystick (default off) [VIA686A/686B only]
1282 ac97_clock - AC'97 codec clock base (default 48000Hz)
1283 dxs_support - support DXS channels,
1284 0 = auto (default), 1 = enable, 2 = disable,
1285 3 = 48k only, 4 = no VRA, 5 = enable any sample
1286 rate and different sample rates on different
1288 [VIA8233/C, 8235, 8237 only]
1289 ac97_quirk - AC'97 workaround for strange hardware
1290 See the description of intel8x0 module for details.
1292 Module supports autoprobe and multiple bus-master chips (max 8).
1294 Note: on some SMP motherboards like MSI 694D the interrupts might
1295 not be generated properly. In such a case, please try to
1296 set the SMP (or MPS) version on BIOS to 1.1 instead of
1297 default value 1.4. Then the interrupt number will be
1298 assigned under 15. You might also upgrade your BIOS.
1300 Note: VIA8233/5/7 (not VIA8233A) can support DXS (direct sound)
1301 channels as the first PCM. On these channels, up to 4
1302 streams can be played at the same time, and the controller
1303 can perform sample rate conversion with separate rates for
1305 As default (dxs_support = 0), 48k fixed rate is chosen
1306 except for the known devices since the output is often
1307 noisy except for 48k on some mother boards due to the
1309 Please try once dxs_support=5 and if it works on other
1310 sample rates (e.g. 44.1kHz of mp3 playback), please let us
1311 know the PCI subsystem vendor/device id's (output of
1313 If dxs_support=5 does not work, try dxs_support=4; if it
1314 doesn't work too, try dxs_support=1. (dxs_support=1 is
1315 usually for old motherboards. The correct implementated
1316 board should work with 4 or 5.) If it still doesn't
1317 work and the default setting is ok, dxs_support=3 is the
1318 right choice. If the default setting doesn't work at all,
1319 try dxs_support=2 to disable the DXS channels.
1320 In any cases, please let us know the result and the
1321 subsystem vendor/device ids.
1323 Note: for the MPU401 on VIA823x, use snd-mpu401 driver
1324 additonally. The mpu_port option is for VIA686 chips only.
1326 Module snd-via82xx-modem
1327 ------------------------
1329 Module for VIA82xx AC97 modem
1331 ac97_clock - AC'97 codec clock base (default 48000Hz)
1333 Module supports up to 8 cards.
1335 Note: The default index value of this module is -2, i.e. the first
1341 Module for virtual rawmidi devices.
1342 This module creates virtual rawmidi devices which communicate
1343 to the corresponding ALSA sequencer ports.
1345 midi_devs - MIDI devices # (1-8, default=4)
1347 Module supports up to 8 cards.
1352 Module for Digigram VX-Pocket VX222, V222 v2 and Mic cards.
1354 mic - Enable Microphone on V222 Mic (NYI)
1355 ibl - Capture IBL size. (default = 0, minimum size)
1357 Module supports up to 8 cards.
1359 When the driver is compiled as a module and the hotplug firmware
1360 is supported, the firmware data is loaded via hotplug automatically.
1361 Install the necessary firmware files in alsa-firmware package.
1362 When no hotplug fw loader is available, you need to load the
1363 firmware via vxloader utility in alsa-tools package. To invoke
1364 vxloader automatically, add the following to /etc/modprobe.conf
1366 install snd-vx222 /sbin/modprobe --first-time -i snd-vx222 && /usr/bin/vxloader
1368 (for 2.2/2.4 kernels, add "post-install /usr/bin/vxloader" to
1369 /etc/modules.conf, instead.)
1370 IBL size defines the interrupts period for PCM. The smaller size
1371 gives smaller latency but leads to more CPU consumption, too.
1372 The size is usually aligned to 126. As default (=0), the smallest
1373 size is chosen. The possible IBL values can be found in
1374 /proc/asound/cardX/vx-status proc file.
1379 Module for Digigram VX-Pocket VX2 PCMCIA card.
1381 ibl - Capture IBL size. (default = 0, minimum size)
1383 Module supports up to 8 cards. The module is compiled only when
1384 PCMCIA is supported on kernel.
1386 To activate the driver via the card manager, you'll need to set
1387 up /etc/pcmcia/vxpocket.conf. See the sound/pcmcia/vx/vxpocket.c.
1389 When the driver is compiled as a module and the hotplug firmware
1390 is supported, the firmware data is loaded via hotplug automatically.
1391 Install the necessary firmware files in alsa-firmware package.
1392 When no hotplug fw loader is available, you need to load the
1393 firmware via vxloader utility in alsa-tools package.
1395 About capture IBL, see the description of snd-vx222 module.
1397 Note: the driver is build only when CONFIG_ISA is set.
1402 Module for Digigram VX-Pocket 440 PCMCIA card.
1404 ibl - Capture IBL size. (default = 0, minimum size)
1406 Module supports up to 8 cards. The module is compiled only when
1407 PCMCIA is supported on kernel.
1409 To activate the driver via the card manager, you'll need to set
1410 up /etc/pcmcia/vxp440.conf. See the sound/pcmcia/vx/vxp440.c.
1412 When the driver is compiled as a module and the hotplug firmware
1413 is supported, the firmware data is loaded via hotplug automatically.
1414 Install the necessary firmware files in alsa-firmware package.
1415 When no hotplug fw loader is available, you need to load the
1416 firmware via vxloader utility in alsa-tools package.
1418 About capture IBL, see the description of snd-vx222 module.
1420 Note: the driver is build only when CONFIG_ISA is set.
1425 Module for Yamaha PCI chips (YMF72x, YMF74x & YMF75x).
1427 mpu_port - 0x300,0x330,0x332,0x334, 0 (disable) by default,
1428 1 (auto-detect for YMF744/754 only)
1429 fm_port - 0x388,0x398,0x3a0,0x3a8, 0 (disable) by default
1430 1 (auto-detect for YMF744/754 only)
1431 joystick_port - 0x201,0x202,0x204,0x205, 0 (disable) by default,
1433 rear_switch - enable shared rear/line-in switch (bool)
1435 Module supports autoprobe and multiple chips (max 8).
1437 The power-management is supported.
1439 Module snd-pdaudiocf
1440 --------------------
1442 Module for Sound Core PDAudioCF sound card.
1444 Note: the driver is build only when CONFIG_ISA is set.
1447 Configuring Non-ISAPNP Cards
1448 ============================
1450 When the kernel is configured with ISA-PnP support, the modules
1451 supporting the isapnp cards will have module options "isapnp".
1452 If this option is set, *only* the ISA-PnP devices will be probed.
1453 For probing the non ISA-PnP cards, you have to pass "isapnp=0" option
1454 together with the proper i/o and irq configuration.
1456 When the kernel is configured without ISA-PnP support, isapnp option
1457 will be not built in.
1460 Module Autoloading Support
1461 ==========================
1463 The ALSA drivers can be loaded automatically on demand by defining
1464 module aliases. The string 'snd-card-%1' is requested for ALSA native
1465 devices where %i is sound card number from zero to seven.
1467 To auto-load an ALSA driver for OSS services, define the string
1468 'sound-slot-%i' where %i means the slot number for OSS, which
1469 corresponds to the card index of ALSA. Usually, define this
1470 as the the same card module.
1472 An example configuration for a single emu10k1 card is like below:
1473 ----- /etc/modprobe.conf
1474 alias snd-card-0 snd-emu10k1
1475 alias sound-slot-0 snd-emu10k1
1476 ----- /etc/modprobe.conf
1478 The available number of auto-loaded sound cards depends on the module
1479 option "cards_limit" of snd module. As default it's set to 1.
1480 To enable the auto-loading of multiple cards, specify the number of
1481 sound cards in that option.
1483 When multiple cards are available, it'd better to specify the index
1484 number for each card via module option, too, so that the order of
1485 cards is kept consistent.
1487 An example configuration for two sound cards is like below:
1489 ----- /etc/modprobe.conf
1491 options snd cards_limit=2
1492 alias snd-card-0 snd-interwave
1493 alias snd-card-1 snd-ens1371
1494 options snd-interwave index=0
1495 options snd-ens1371 index=1
1497 alias sound-slot-0 snd-interwave
1498 alias sound-slot-1 snd-ens1371
1499 ----- /etc/moprobe.conf
1501 In this example, the interwave card is always loaded as the first card
1502 (index 0) and ens1371 as the second (index 1).
1505 ALSA PCM devices to OSS devices mapping
1506 =======================================
1508 /dev/snd/pcmC0D0[c|p] -> /dev/audio0 (/dev/audio) -> minor 4
1509 /dev/snd/pcmC0D0[c|p] -> /dev/dsp0 (/dev/dsp) -> minor 3
1510 /dev/snd/pcmC0D1[c|p] -> /dev/adsp0 (/dev/adsp) -> minor 12
1511 /dev/snd/pcmC1D0[c|p] -> /dev/audio1 -> minor 4+16 = 20
1512 /dev/snd/pcmC1D0[c|p] -> /dev/dsp1 -> minor 3+16 = 19
1513 /dev/snd/pcmC1D1[c|p] -> /dev/adsp1 -> minor 12+16 = 28
1514 /dev/snd/pcmC2D0[c|p] -> /dev/audio2 -> minor 4+32 = 36
1515 /dev/snd/pcmC2D0[c|p] -> /dev/dsp2 -> minor 3+32 = 39
1516 /dev/snd/pcmC2D1[c|p] -> /dev/adsp2 -> minor 12+32 = 44
1518 The first number from /dev/snd/pcmC{X}D{Y}[c|p] expression means
1519 sound card number and second means device number. The ALSA devices
1520 have either 'c' or 'p' suffix indicating the direction, capture and
1521 playback, respectively.
1523 Please note that the device mapping above may be varied via the module
1524 options of snd-pcm-oss module.
1530 The ALSA driver fully supports the devfs extension.
1531 You should add lines below to your devfsd.conf file:
1533 LOOKUP snd MODLOAD ACTION snd
1534 REGISTER ^sound/.* PERMISSIONS root.audio 660
1535 REGISTER ^snd/.* PERMISSIONS root.audio 660
1537 Warning: These lines assume that you have the audio group in your system.
1538 Otherwise replace audio word with another group name (root for
1542 Proc interfaces (/proc/asound)
1543 ==============================
1545 /proc/asound/card#/pcm#[cp]/oss
1546 -------------------------------
1547 String "erase" - erase all additional informations about OSS applications
1548 String "<app_name> <fragments> <fragment_size> [<options>]"
1550 <app_name> - name of application with (higher priority) or without path
1551 <fragments> - number of fragments or zero if auto
1552 <fragment_size> - size of fragment in bytes or zero if auto
1553 <options> - optional parameters
1554 - disable the application tries to open a pcm device for
1555 this channel but does not want to use it.
1556 (Cause a bug or mmap needs)
1557 It's good for Quake etc...
1558 - direct don't use plugins
1559 - block force block mode (rvplayer)
1560 - non-block force non-block mode
1561 - whole-frag write only whole fragments (optimization affecting
1563 - no-silence do not fill silence ahead to avoid clicks
1565 Example: echo "x11amp 128 16384" > /proc/asound/card0/pcm0p/oss
1566 echo "squake 0 0 disable" > /proc/asound/card0/pcm0c/oss
1567 echo "rvplayer 0 0 block" > /proc/asound/card0/pcm0p/oss
1570 Early Buffer Allocation
1571 =======================
1573 Some drivers (e.g. hdsp) require the large contiguous buffers, and
1574 sometimes it's too late to find such spaces when the driver module is
1575 actually loaded due to memory fragmentation. You can pre-allocate the
1576 PCM buffers by loading snd-page-alloc module and write commands to its
1577 proc file in prior, for example, in the early boot stage like
1578 /etc/init.d/*.local scripts.
1580 Reading the proc file /proc/drivers/snd-page-alloc shows the current
1581 usage of page allocation. In writing, you can send the following
1582 commands to the snd-page-alloc driver:
1584 - add VENDOR DEVICE MASK SIZE BUFFERS
1586 VENDOR and DEVICE are PCI vendor and device IDs. They take
1587 integer numbers (0x prefix is needed for the hex).
1588 MASK is the PCI DMA mask. Pass 0 if not restricted.
1589 SIZE is the size of each buffer to allocate. You can pass
1590 k and m suffix for KB and MB. The max number is 16MB.
1591 BUFFERS is the number of buffers to allocate. It must be greater
1592 than 0. The max number is 4.
1596 This will erase the all pre-allocated buffers which are not in
1603 ALSA project homepage
1604 http://www.alsa-project.org