Linus Torvalds [Fri, 27 May 2011 17:12:35 +0000 (10:12 -0700)]
Merge git://git.infradead.org/battery-2.6
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
Linus Torvalds [Fri, 27 May 2011 17:11:42 +0000 (10:11 -0700)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
hwmon: (coretemp) Fix section mismatch
hwmon: (pmbus) Initialize sysfs attributes
hwmon: (coretemp) Update comments describing the handling of HT CPUs
hwmon: (coretemp) Initialize sysfs attributes
Linus Torvalds [Fri, 27 May 2011 17:10:51 +0000 (10:10 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
ASoC: Fix power down for widgetless per-card DAPM context case
ASoC: wm1250-ev1: Define "WM1250 Output" with SND_SOC_DAPM_OUTPUT
ASoC: Remove duplicate linux/delay.h inclusion.
ASoC: sam9g20_wm8731: use the proper SYSCKL value
ASoC: wm8731: fix wm8731_check_osc() connected condition
ALSA: hda - Reorganize controller quriks with bit flags
ALSA: hda - Use snd_printd() in snd_hda_parse_pin_def_config()
ALSA: core: remove unused variables.
ALSA: HDA: Increase MAX_HDMI_PINS
ALSA: PCM - Don't check DMA time-out too shortly
MAINTAINERS: add FireWire audio maintainer
ALSA: usb-audio: more control quirks for M-Audio FastTrack devices
ALSA: usb-audio: add new quirk type QUIRK_AUDIO_STANDARD_MIXER
ALSA: usb-audio: export snd_usb_feature_unit_ctl
ALSA: usb-audio: rework add_control_to_empty()
ALSA: usb-audio: move assignment of chip->ctrl_intf
ALSA: hda - Use model=auto for Lenovo G555
ALSA: HDA: Unify HDMI hotplug handling.
ALSA: hda - Force AD1988_6STACK_DIG for Asus M3N-HT Deluxe
ASoC: core - remove superfluous new line.
...
Jean Delvare [Thu, 26 May 2011 10:01:54 +0000 (06:01 -0400)]
hwmon: (coretemp) Fix section mismatch
chk_ucode_version() is only called from coretemp_probe() which is
__devinit, so it can be marked __devinit too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Guenter Roeck [Tue, 24 May 2011 19:16:40 +0000 (12:16 -0700)]
hwmon: (pmbus) Initialize sysfs attributes
Initialize sysfs attrs before device_create_file() call to suppress
lockdep_init_map() warning:
WARNING: at kernel/lockdep.c:2701 lockdep_init_map+0x12d/0x140()
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org # .39.x
Guenter Roeck [Mon, 23 May 2011 20:52:35 +0000 (13:52 -0700)]
hwmon: (coretemp) Update comments describing the handling of HT CPUs
Update comments describing the handling of HT CPUs based on review feedback.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Sergey Senozhatsky [Tue, 24 May 2011 11:28:31 +0000 (07:28 -0400)]
hwmon: (coretemp) Initialize sysfs attributes
Initialize sysfs attrs before device_create_file() call to suppress lockdep_init_map()
warning:
[ 3.653628] WARNING: at kernel/lockdep.c:2885 lockdep_init_map+0xea/0x43c()
[ 3.653698] Modules linked in:
[ 3.654835] Pid: 1, comm: swapper Not tainted 2.6.39-dbg-git8-05624-g46187f8 #576
[ 3.656014] Call Trace:
[ 3.657139] [<
ffffffff8103e4b4>] warn_slowpath_common+0x7e/0x96
[ 3.658298] [<
ffffffff8103e4e1>] warn_slowpath_null+0x15/0x17
[ 3.659460] [<
ffffffff8106d7b9>] lockdep_init_map+0xea/0x43c
[ 3.660616] [<
ffffffff81163c1a>] sysfs_add_file_mode+0x5d/0xa8
[ 3.661785] [<
ffffffff81163c71>] sysfs_add_file+0xc/0xe
[ 3.662929] [<
ffffffff81163d26>] sysfs_create_file+0x23/0x25
[ 3.664045] [<
ffffffff813724d1>] device_create_file+0x14/0x16
[ 3.665172] [<
ffffffff81460ed4>] coretemp_probe+0xf9/0x185
[ 3.666306] [<
ffffffff8137638e>] platform_drv_probe+0x12/0x14
[ 3.667420] [<
ffffffff81375321>] driver_probe_device+0xb0/0x14b
[ 3.668542] [<
ffffffff8137546d>] __device_attach+0x35/0x3a
[ 3.669710] [<
ffffffff81375438>] ? __driver_attach+0x7c/0x7c
[ 3.670816] [<
ffffffff8137426b>] bus_for_each_drv+0x54/0x88
[ 3.671921] [<
ffffffff81375231>] device_attach+0x77/0x9b
[ 3.673027] [<
ffffffff81374aef>] bus_probe_device+0x22/0x39
[ 3.674137] [<
ffffffff81373235>] device_add+0x3c1/0x550
[ 3.675249] [<
ffffffff81371ed9>] ? dev_set_name+0x3c/0x3e
[ 3.676371] [<
ffffffff813769f3>] platform_device_add+0x10c/0x156
[ 3.677491] [<
ffffffff8146af9c>] get_core_online+0xab/0x16e
[ 3.678608] [<
ffffffff81ad8070>] coretemp_init+0x4b/0x80
[ 3.679724] [<
ffffffff81ad8025>] ? hwmon_init+0xee/0xee
[ 3.680853] [<
ffffffff8100020a>] do_one_initcall+0x7a/0x13c
[ 3.681975] [<
ffffffff81aaac74>] kernel_init+0xe1/0x15b
[ 3.683081] [<
ffffffff8147e4e4>] kernel_thread_helper+0x4/0x10
[ 3.684174] [<
ffffffff8102d48c>] ? finish_task_switch+0x76/0xf0
[ 3.685266] [<
ffffffff81477918>] ? retint_restore_args+0x13/0x13
[ 3.686356] [<
ffffffff81aaab93>] ? start_kernel+0x3ee/0x3ee
[ 3.687425] [<
ffffffff8147e4e0>] ? gs_change+0x13/0x13
[ 3.688489] ---[ end trace
7392ad3e6a92ae39 ]---
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Takashi Iwai [Fri, 27 May 2011 06:03:03 +0000 (08:03 +0200)]
Merge branch 'fix/asoc' into for-linus
Takashi Iwai [Fri, 27 May 2011 06:02:59 +0000 (08:02 +0200)]
Merge branch 'fix/misc' into for-linus
Linus Torvalds [Fri, 27 May 2011 02:01:15 +0000 (19:01 -0700)]
Merge branch 'upstream/tidy-xen-mmu-2.6.39' of git://git./linux/kernel/git/jeremy/xen
* 'upstream/tidy-xen-mmu-2.6.39' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: fix compile without CONFIG_XEN_DEBUG_FS
Use arbitrary_virt_to_machine() to deal with ioremapped pud updates.
Use arbitrary_virt_to_machine() to deal with ioremapped pmd updates.
xen/mmu: remove all ad-hoc stats stuff
xen: use normal virt_to_machine for ptes
xen: make a pile of mmu pvop functions static
vmalloc: remove vmalloc_sync_all() from alloc_vm_area()
xen: condense everything onto xen_set_pte
xen: use mmu_update for xen_set_pte_at()
xen: drop all the special iomap pte paths.
Linus Torvalds [Tue, 24 May 2011 20:48:51 +0000 (13:48 -0700)]
selinux: don't pass in NULL avd to avc_has_perm_noaudit
Right now security_get_user_sids() will pass in a NULL avd pointer to
avc_has_perm_noaudit(), which then forces that function to have a dummy
entry for that case and just generally test it.
Don't do it. The normal callers all pass a real avd pointer, and this
helper function is incredibly hot. So don't make avc_has_perm_noaudit()
do conditional stuff that isn't needed for the common case.
This also avoids some duplicated stack space.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 27 May 2011 00:27:35 +0000 (17:27 -0700)]
Merge git://git./linux/kernel/git/pkl/squashfs-linus
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
Squashfs: update email address
Squashfs: add extra sanity checks at mount time
Squashfs: add sanity checks to fragment reading at mount time
Squashfs: add sanity checks to lookup table reading at mount time
Squashfs: add sanity checks to id reading at mount time
Squashfs: add sanity checks to xattr reading at mount time
Squashfs: reverse order of filesystem table reading
Squashfs: move table allocation into squashfs_read_table()
Akinobu Mita [Thu, 26 May 2011 23:26:13 +0000 (16:26 -0700)]
m68knommu: use generic find_next_bit_le()
The implementation of find_next_bit_le() on m68knommu is identical with
the generic implementation of find_next_bit_le().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 26 May 2011 23:26:12 +0000 (16:26 -0700)]
s390: use asm-generic/bitops/le.h
The previous style change enables to use asm-generic/bitops/le.h on s390.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 26 May 2011 23:26:11 +0000 (16:26 -0700)]
arm: use asm-generic/bitops/le.h
The previous style change enables to use asm-generic/bitops/le.h on arm.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 26 May 2011 23:26:10 +0000 (16:26 -0700)]
arch: remove CONFIG_GENERIC_FIND_{NEXT_BIT,BIT_LE,LAST_BIT}
By the previous style change, CONFIG_GENERIC_FIND_NEXT_BIT,
CONFIG_GENERIC_FIND_BIT_LE, and CONFIG_GENERIC_FIND_LAST_BIT are not used
to test for existence of find bitops anymore.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 26 May 2011 23:26:09 +0000 (16:26 -0700)]
bitops: add #ifndef for each of find bitops
The style that we normally use in asm-generic is to test the macro itself
for existence, so in asm-generic, do:
#ifndef find_next_zero_bit_le
extern unsigned long find_next_zero_bit_le(const void *addr,
unsigned long size, unsigned long offset);
#endif
and in the architectures, write
static inline unsigned long find_next_zero_bit_le(const void *addr,
unsigned long size, unsigned long offset)
#define find_next_zero_bit_le find_next_zero_bit_le
This adds the #ifndef for each of the find bitops in the generic header
and source files.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 26 May 2011 23:26:06 +0000 (16:26 -0700)]
arch: add #define for each of optimized find bitops
The style that we normally use in asm-generic is to test the macro itself
for existence, so in asm-generic, do:
#ifndef find_next_zero_bit_le
extern unsigned long find_next_zero_bit_le(const void *addr,
unsigned long size, unsigned long offset);
#endif
and in the architectures, write
static inline unsigned long find_next_zero_bit_le(const void *addr,
unsigned long size, unsigned long offset)
#define find_next_zero_bit_le find_next_zero_bit_le
This adds the #define for each of the optimized find bitops in the
architectures.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Thu, 26 May 2011 23:26:05 +0000 (16:26 -0700)]
m68knommu: fix build error due to the lack of find_next_bit_le()
m68knommu can't build ext4, udf, and ocfs2 due to the lack of
find_next_bit_le().
This implements find_next_bit_le() on m68knommu by duplicating the generic
find_next_bit_le() in lib/find_next_bit.c.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clifton Barnes [Thu, 26 May 2011 23:26:04 +0000 (16:26 -0700)]
w1: add Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC support
Add support for the Maxim/Dallas DS2780 Stand-Alone Fuel Gauge IC.
It was suggested to combine this functionality with the current ds2782
driver. Unfortunately, I'm unable to commit the time to refactoring this
driver to that extent and I don't have a platform with the ds2782 part to
validate that there are no regression issues by adding this functionality.
[akpm@linux-foundation.org: use min_t()]
Signed-off-by: Clifton Barnes <cabarnes@indesign-llc.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Fries [Thu, 26 May 2011 23:26:03 +0000 (16:26 -0700)]
w1: have netlink search update kernel list
Reorganize so the netlink connector one wire search command will update
the kernel list of detected slave devices. Otherwise, a newly detected
device is unusable because unless it's in the kernel list of known devices
any commands will result in ENODEV status.
Signed-off-by: David Fries <David@Fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean-François Dagenais [Thu, 26 May 2011 23:26:02 +0000 (16:26 -0700)]
w1: complete the 1-wire (w1) ds1wm driver search algorithm
This adds multi-slave support of the w1 bus for the ds1wm Synthesizable
1-Wire Bus Master. Also many fixes and tweaks based on the rev3 of the
datasheet http://datasheets.maxim-ic.com/en/ds/DS1WM.pdf
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean-François Dagenais [Thu, 26 May 2011 23:26:02 +0000 (16:26 -0700)]
w1: add 1-wire (w1) DS2408 8-Channel Addressable Switch support
This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.
[randy.dunlap@oracle.com: fix w1_ds2408.c printk formats]
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jean-François Dagenais [Thu, 26 May 2011 23:26:01 +0000 (16:26 -0700)]
w1: add 1-wire (w1) reset and resume command API support
The first patch adds generic functionnality to w1_io for Resume Command
[A5h] lots of slaves support. I found it useful for multi-commands/reset
workflows with the same slave on a multi-slave bus.
This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander. Enjoy!
The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK. I took them
out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA
through pcie) and found them irrelevant.
The clock freq/divisors at the top of ds1wm.c did not have the MSB set to
1. This bit is CLK_EN which turns the whole prescaler and dividers on.
The driver never mentionned this bit either, so I just included this bit
right in the table entries. I also took the liberty to add a couple of
entries to the table. The spec doesn't explicitely mentions these
possibilities but the description and examination of the core shows the
prescalers & dividers can be used for more than the table explicitely
shows. The table I enlarged still doesn't cover all possibilities, but
it's a good start.
I also made a few tweaks to a couple of the read and write algorithms
which made sense while I had my head very deep in the ds1wm documentation.
We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and
ds2433 at the same time doing extensive interaction. It proved quite
stable in our production environment.
This patch:
Add generic functionnality to w1_io for Resume Command [A5h] lots of
slaves support.
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rakib Mullick [Thu, 26 May 2011 23:26:00 +0000 (16:26 -0700)]
kernel/profile.c: remove some duplicate code from profile_hits()
profile_hits() has a common check for prof_on and prof_buffer regardless
of SMP or !SMP. So, remove some duplicate code by splitting profile_hits
into two.
[akpm@linux-foundation.org: make do_profile_hits static]
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Thu, 26 May 2011 23:25:59 +0000 (16:25 -0700)]
drivers/char/ppdev.c: put gotten port value
parport_find_number() calls parport_get_port() on its result, so there
should be a corresponding call to parport_put_port() before dropping the
reference. Similar code is found in the function register_device() in the
same file.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression struct parport * x;
expression ra,rr;
statement S1,S2;
@@
x = parport_find_number(...)
... when != x = rr
when any
when != parport_put_port(x,...)
when != if (...) { ... parport_put_port(x,...) ...}
(
if(<+...x...+>) S1 else S2
|
if(...) { ... when != x = ra
when forall
when != parport_put_port(x,...)
*return...;
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lai Jiangshan [Thu, 26 May 2011 23:25:58 +0000 (16:25 -0700)]
edac,rcu: use synchronize_rcu() instead of call_rcu()+rcu_barrier()
synchronize_rcu() does the stuff as needed.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sisir Koppaka [Thu, 26 May 2011 23:25:57 +0000 (16:25 -0700)]
pid: fix typo in function description
finds is misspelt as finr. No functional change.
Signed-off-by: Sisir Koppaka <sisir.koppaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Timo Warns [Thu, 26 May 2011 23:25:57 +0000 (16:25 -0700)]
fs/partitions/efi.c: corrupted GUID partition tables can cause kernel oops
The kernel automatically evaluates partition tables of storage devices.
The code for evaluating GUID partitions (in fs/partitions/efi.c) contains
a bug that causes a kernel oops on certain corrupted GUID partition
tables.
This bug has security impacts, because it allows, for example, to
prepare a storage device that crashes a kernel subsystem upon connecting
the device (e.g., a "USB Stick of (Partial) Death").
crc = efi_crc32((const unsigned char *) (*gpt), le32_to_cpu((*gpt)->header_size));
computes a CRC32 checksum over gpt covering (*gpt)->header_size bytes.
There is no validation of (*gpt)->header_size before the efi_crc32 call.
A corrupted partition table may have large values for (*gpt)->header_size.
In this case, the CRC32 computation access memory beyond the memory
allocated for gpt, which may cause a kernel heap overflow.
Validate value of GUID partition table header size.
[akpm@linux-foundation.org: fix layout and indenting]
Signed-off-by: Timo Warns <warns@pre-sense.de>
Cc: Matt Domsch <Matt_Domsch@dell.com>
Cc: Eugene Teo <eugeneteo@kernel.sg>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rakib Mullick [Thu, 26 May 2011 23:25:56 +0000 (16:25 -0700)]
drivers/char/mspec.c: use {k,v}zalloc to allocate memory
Let memory allocator initialize the allocated memory as null, thus remove
the use of memset.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Thu, 26 May 2011 23:25:55 +0000 (16:25 -0700)]
ipmi: convert to seq_file interface
The ->read_proc interface is going away, convert to seq_file.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc:Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olaf Hering [Thu, 26 May 2011 23:25:54 +0000 (16:25 -0700)]
fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages
The balloon driver in a Xen guest frees guest pages and marks them as
mmio. When the kernel crashes and the crash kernel attempts to read the
oldmem via /proc/vmcore a read from ballooned pages will generate 100%
load in dom0 because Xen asks qemu-dm for the page content. Since the
reads come in as 8byte requests each ballooned page is tried 512 times.
With this change a hook can be registered which checks wether the given
pfn is really ram. The hook has to return a value > 0 for ram pages, a
value < 0 on error (because the hypercall is not known) and 0 for non-ram
pages.
This will reduce the time to read /proc/vmcore. Without this change a
512M guest with 128M crashkernel region needs 200 seconds to read it, with
this change it takes just 2 seconds.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Thu, 26 May 2011 23:25:53 +0000 (16:25 -0700)]
proc: fix pagemap_read() error case
Currently, pagemap_read() has three error and/or corner case handling
mistake.
(1) If ppos parameter is wrong, mm refcount will be leak.
(2) If count parameter is 0, mm refcount will be leak too.
(3) If the current task is sleeping in kmalloc() and the system
is out of memory and oom-killer kill the proc associated task,
mm_refcount prevent the task free its memory. then system may
hang up.
<Quote Hugh's explain why we shold call kmalloc() before get_mm()>
check_mem_permission gets a reference to the mm. If we
__get_free_page after check_mem_permission, imagine what happens if the
system is out of memory, and the mm we're looking at is selected for
killing by the OOM killer: while we wait in __get_free_page for more
memory, no memory is freed from the selected mm because it cannot reach
exit_mmap while we hold that reference.
This patch fixes the above three.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jovi Zhang <bookjovi@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Stephen Wilson <wilsons@start.ca>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Thu, 26 May 2011 23:25:52 +0000 (16:25 -0700)]
proc: put check_mem_permission after __get_free_page in mem_write
It whould be better if put check_mem_permission after __get_free_page in
mem_write, to be same as function mem_read.
Hugh Dickins explained the reason.
check_mem_permission gets a reference to the mm. If we __get_free_page
after check_mem_permission, imagine what happens if the system is out
of memory, and the mm we're looking at is selected for killing by the
OOM killer: while we wait in __get_free_page for more memory, no memory
is freed from the selected mm because it cannot reach exit_mmap while
we hold that reference.
Reported-by: Jovi Zhang <bookjovi@gmail.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Stephen Wilson <wilsons@start.ca>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yuanhan Liu [Thu, 26 May 2011 23:25:51 +0000 (16:25 -0700)]
proc/stat: use defined macro KMALLOC_MAX_SIZE
There is a macro for the max size kmalloc can allocate, so use it instead
of a hardcoded number.
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 26 May 2011 23:25:51 +0000 (16:25 -0700)]
proc: constify status array
No need for this local array to be writable, so mark it const.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan [Thu, 26 May 2011 23:25:50 +0000 (16:25 -0700)]
fs/proc: convert to kstrtoX()
Convert fs/proc/ from strict_strto*() to kstrto*() functions.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 26 May 2011 23:25:46 +0000 (16:25 -0700)]
coredump: add support for exe_file in core name
Now, exe_file is not proc FS dependent, so we can use it to name core
file. So we add %E pattern for core file name cration which extract path
from mm_struct->exe_file. Then it converts slashes to exclamation marks
and pastes the result to the core file name itself.
This is useful for environments where binary names are longer than 16
character (the current->comm limitation). Also where there are binaries
with same name but in a different path. Further in case the binery itself
changes its current->comm after exec.
So by doing (s/$/#/ -- # is treated as git comment):
$ sysctl kernel.core_pattern='core.%p.%e.%E'
$ ln /bin/cat cat45678901234567890
$ ./cat45678901234567890
^Z
$ rm cat45678901234567890
$ fg
^\Quit (core dumped)
$ ls core*
we now get:
core.2434.cat456789012345.!root!cat45678901234567890 (deleted)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 26 May 2011 23:25:46 +0000 (16:25 -0700)]
mm: extract exe_file handling from procfs
Setup and cleanup of mm_struct->exe_file is currently done in fs/proc/.
This was because exe_file was needed only for /proc/<pid>/exe. Since we
will need the exe_file functionality also for core dumps (so core name can
contain full binary path), built this functionality always into the
kernel.
To achieve that move that out of proc FS to the kernel/ where in fact it
should belong. By doing that we can make dup_mm_exe_file static. Also we
can drop linux/proc_fs.h inclusion in fs/exec.c and kernel/fork.c.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 26 May 2011 23:25:45 +0000 (16:25 -0700)]
kgdbts: unify/generalize gdb breakpoint adjustment
The Blackfin arch, like the x86 arch, needs to adjust the PC manually
after a breakpoint is hit as normally this is handled by the remote gdb.
However, rather than starting another arch ifdef mess, create a common
GDB_ADJUSTS_BREAK_OFFSET define for any arch to opt-in via their kgdb.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 26 May 2011 23:25:44 +0000 (16:25 -0700)]
sh: convert to asm-generic ptrace.h
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 26 May 2011 23:25:43 +0000 (16:25 -0700)]
x86: convert to asm-generic ptrace.h
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 26 May 2011 23:25:42 +0000 (16:25 -0700)]
Blackfin: convert to asm-generic ptrace.h
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Frysinger [Thu, 26 May 2011 23:25:39 +0000 (16:25 -0700)]
asm-generic/ptrace.h: start a common low level ptrace helper
This is a series of low level ptrace unification steps to make it easier
for common code (like KGDB) to poke at register state. This also avoids
having to duplicate higher level operations for most ports which don't
have special needs for accessing things.
This patch:
This implements a bunch of helper funcs for poking the registers of a
ptrace structure. Now common code should be able to portably update
specific registers (like kgdb updating the PC).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: Dongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ying Han [Thu, 26 May 2011 23:25:38 +0000 (16:25 -0700)]
memcg: add the pagefault count into memcg stats
Two new stats in per-memcg memory.stat which tracks the number of page
faults and number of major page faults.
"pgfault"
"pgmajfault"
They are different from "pgpgin"/"pgpgout" stat which count number of
pages charged/discharged to the cgroup and have no meaning of reading/
writing page to disk.
It is valuable to track the two stats for both measuring application's
performance as well as the efficiency of the kernel page reclaim path.
Counting pagefaults per process is useful, but we also need the aggregated
value since processes are monitored and controlled in cgroup basis in
memcg.
Functional test: check the total number of pgfault/pgmajfault of all
memcgs and compare with global vmstat value:
$ cat /proc/vmstat | grep fault
pgfault 1070751
pgmajfault 553
$ cat /dev/cgroup/memory.stat | grep fault
pgfault 1071138
pgmajfault 553
total_pgfault 1071142
total_pgmajfault 553
$ cat /dev/cgroup/A/memory.stat | grep fault
pgfault 199
pgmajfault 0
total_pgfault 199
total_pgmajfault 0
Performance test: run page fault test(pft) wit 16 thread on faulting in
15G anon pages in 16G container. There is no regression noticed on the
"flt/cpu/s"
Sample output from pft:
TAG pft:anon-sys-default:
Gb Thr CLine User System Wall flt/cpu/s fault/wsec
15 16 1 0.67s 233.41s 14.76s 16798.546 266356.260
+-------------------------------------------------------------------------+
N Min Max Median Avg Stddev
x 10 16682.962 17344.027 16913.524 16928.812 166.5362
+ 10 16695.568 16923.896 16820.604 16824.652 84.816568
No difference proven at 95.0% confidence
[akpm@linux-foundation.org: fix build]
[hughd@google.com: shmem fix]
Signed-off-by: Ying Han <yinghan@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ying Han [Thu, 26 May 2011 23:25:37 +0000 (16:25 -0700)]
memcg: add memory.numastat api for numa statistics
The new API exports numa_maps per-memcg basis. This is a piece of useful
information where it exports per-memcg page distribution across real numa
nodes.
One of the usecases is evaluating application performance by combining
this information w/ the cpu allocation to the application.
The output of the memory.numastat tries to follow w/ simiar format of
numa_maps like:
total=<total pages> N0=<node 0 pages> N1=<node 1 pages> ...
file=<total file pages> N0=<node 0 pages> N1=<node 1 pages> ...
anon=<total anon pages> N0=<node 0 pages> N1=<node 1 pages> ...
unevictable=<total anon pages> N0=<node 0 pages> N1=<node 1 pages> ...
And we have per-node:
total = file + anon + unevictable
$ cat /dev/cgroup/memory/memory.numa_stat
total=250020 N0=87620 N1=52367 N2=45298 N3=64735
file=225232 N0=83402 N1=46160 N2=40522 N3=55148
anon=21053 N0=3424 N1=6207 N2=4776 N3=6646
unevictable=3735 N0=794 N1=0 N2=0 N3=2941
Signed-off-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ying Han [Thu, 26 May 2011 23:25:36 +0000 (16:25 -0700)]
memcg: rename mem_cgroup_zone_nr_pages() to mem_cgroup_zone_nr_lru_pages()
The caller of the function has been renamed to zone_nr_lru_pages(), and
this is just fixing up in the memcg code. The current name is easily to
be mis-read as zone's total number of pages.
Signed-off-by: Ying Han <yinghan@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Thu, 26 May 2011 23:25:35 +0000 (16:25 -0700)]
memcg: remove unused retry signal from reclaim
If the memcg reclaim code detects the target memcg below its limit it
exits and returns a guaranteed non-zero value so that the charge is
retried.
Nowadays, the charge side checks the memcg limit itself and does not rely
on this non-zero return value trick.
This patch removes it. The reclaim code will now always return the true
number of pages it reclaimed on its own.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel<riel@redhat.com>
Acked-by: Ying Han<yinghan@google.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KAMEZAWA Hiroyuki [Thu, 26 May 2011 23:25:34 +0000 (16:25 -0700)]
memcg: fix get_scan_count() for small targets
During memory reclaim we determine the number of pages to be scanned per
zone as
(anon + file) >> priority.
Assume
scan = (anon + file) >> priority.
If scan < SWAP_CLUSTER_MAX, the scan will be skipped for this time and
priority gets higher. This has some problems.
1. This increases priority as 1 without any scan.
To do scan in this priority, amount of pages should be larger than 512M.
If pages>>priority < SWAP_CLUSTER_MAX, it's recorded and scan will be
batched, later. (But we lose 1 priority.)
If memory size is below 16M, pages >> priority is 0 and no scan in
DEF_PRIORITY forever.
2. If zone->all_unreclaimabe==true, it's scanned only when priority==0.
So, x86's ZONE_DMA will never be recoverred until the user of pages
frees memory by itself.
3. With memcg, the limit of memory can be small. When using small memcg,
it gets priority < DEF_PRIORITY-2 very easily and need to call
wait_iff_congested().
For doing scan before priorty=9, 64MB of memory should be used.
Then, this patch tries to scan SWAP_CLUSTER_MAX of pages in force...when
1. the target is enough small.
2. it's kswapd or memcg reclaim.
Then we can avoid rapid priority drop and may be able to recover
all_unreclaimable in a small zones. And this patch removes nr_saved_scan.
This will allow scanning in this priority even when pages >> priority is
very small.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Ying Han <yinghan@google.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ying Han [Thu, 26 May 2011 23:25:33 +0000 (16:25 -0700)]
memcg: reclaim memory from nodes in round-robin order
Presently, memory cgroup's direct reclaim frees memory from the current
node. But this has some troubles. Usually when a set of threads works in
a cooperative way, they tend to operate on the same node. So if they hit
limits under memcg they will reclaim memory from themselves, damaging the
active working set.
For example, assume 2 node system which has Node 0 and Node 1 and a memcg
which has 1G limit. After some work, file cache remains and the usages
are
Node 0: 1M
Node 1: 998M.
and run an application on Node 0, it will eat its foot before freeing
unnecessary file caches.
This patch adds round-robin for NUMA and adds equal pressure to each node.
When using cpuset's spread memory feature, this will work very well.
But yes, a better algorithm is needed.
[akpm@linux-foundation.org: comment editing]
[kamezawa.hiroyu@jp.fujitsu.com: fix time comparisons]
Signed-off-by: Ying Han <yinghan@google.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Namhyung Kim [Thu, 26 May 2011 23:25:32 +0000 (16:25 -0700)]
MAINTAINERS: add mm/page_cgroup.c into memcg subsystem
AFAICS mm/page_cgroup.c is for memcg subsystem, but it was directed only
to generic cgroup maintainers. Fix it.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Namhyung Kim [Thu, 26 May 2011 23:25:31 +0000 (16:25 -0700)]
memcg: move page-freeing code out of lock
Move page-freeing code out of swap_cgroup_mutex in the hope that it could
reduce few of theoretical contentions between swapons and/or swapoffs.
This is just a cleanup, no functional changes.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Namhyung Kim [Thu, 26 May 2011 23:25:30 +0000 (16:25 -0700)]
memcg: fix off-by-one when calculating swap cgroup map length
It allocated one more page than necessary if @max_pages was a multiple of
SC_PER_PAGE.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Namhyung Kim [Thu, 26 May 2011 23:25:29 +0000 (16:25 -0700)]
memcg: mark init_section_page_cgroup() properly
Commit
ca371c0d7e23 ("memcg: fix page_cgroup fatal error in FLATMEM")
removes call to alloc_bootmem() in the function so that it can be marked
as __meminit to reduce memory usage when MEMORY_HOTPLUG=n.
Also as the new helper function alloc_page_cgroup() is called only in the
function, it should be marked too.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Michal Hocko [Thu, 26 May 2011 23:25:28 +0000 (16:25 -0700)]
memcg: remove pointless next_mz nullification in mem_cgroup_soft_limit_reclaim()
next_mz is assigned to NULL if __mem_cgroup_largest_soft_limit_node
selects the same mz. This doesn't make much sense as we assign to the
variable right in the next loop.
Compiler will probably optimize this out but it is little bit confusing
for the code reading.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ying Han [Thu, 26 May 2011 23:25:27 +0000 (16:25 -0700)]
memcg: add the soft_limit reclaim in global direct reclaim.
We recently added the change in global background reclaim which counts the
return value of soft_limit reclaim. Now this patch adds the similar logic
on global direct reclaim.
We should skip scanning global LRU on shrink_zone if soft_limit reclaim
does enough work. This is the first step where we start with counting the
nr_scanned and nr_reclaimed from soft_limit reclaim into global
scan_control.
Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ying Han [Thu, 26 May 2011 23:25:25 +0000 (16:25 -0700)]
memcg: count the soft_limit reclaim in global background reclaim
The global kswapd scans per-zone LRU and reclaims pages regardless of the
cgroup. It breaks memory isolation since one cgroup can end up reclaiming
pages from another cgroup. Instead we should rely on memcg-aware target
reclaim including per-memcg kswapd and soft_limit hierarchical reclaim under
memory pressure.
In the global background reclaim, we do soft reclaim before scanning the
per-zone LRU. However, the return value is ignored. This patch is the first
step to skip shrink_zone() if soft_limit reclaim does enough work.
This is part of the effort which tries to reduce reclaiming pages in global
LRU in memcg. The per-memcg background reclaim patchset further enhances the
per-cgroup targetting reclaim, which I should have V4 posted shortly.
Try running multiple memory intensive workloads within seperate memcgs. Watch
the counters of soft_steal in memory.stat.
$ cat /dev/cgroup/A/memory.stat | grep 'soft'
soft_steal 240000
soft_scan 240000
total_soft_steal 240000
total_soft_scan 240000
This patch:
In the global background reclaim, we do soft reclaim before scanning the
per-zone LRU. However, the return value is ignored.
We would like to skip shrink_zone() if soft_limit reclaim does enough
work. Also, we need to make the memory pressure balanced across per-memcg
zones, like the logic vm-core. This patch is the first step where we
start with counting the nr_scanned and nr_reclaimed from soft_limit
reclaim into the global scan_control.
Signed-off-by: Ying Han <yinghan@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 26 May 2011 23:25:24 +0000 (16:25 -0700)]
mm: move enum vm_event_item into a standalone header file
enums are problematic because they cannot be forward-declared:
akpm2:/home/akpm> cat t.c
enum foo;
static inline void bar(enum foo f)
{
}
akpm2:/home/akpm> gcc -c t.c
t.c:4: error: parameter 1 ('f') has incomplete type
So move the enum's definition into a standalone header file which can be used
wherever its definition is needed.
Cc: Ying Han <yinghan@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Lezcano [Thu, 26 May 2011 23:25:23 +0000 (16:25 -0700)]
cgroup: remove the ns_cgroup
The ns_cgroup is an annoying cgroup at the namespace / cgroup frontier and
leads to some problems:
* cgroup creation is out-of-control
* cgroup name can conflict when pids are looping
* it is not possible to have a single process handling a lot of
namespaces without falling in a exponential creation time
* we may want to create a namespace without creating a cgroup
The ns_cgroup was replaced by a compatibility flag 'clone_children',
where a newly created cgroup will copy the parent cgroup values.
The userspace has to manually create a cgroup and add a task to
the 'tasks' file.
This patch removes the ns_cgroup as suggested in the following thread:
https://lists.linux-foundation.org/pipermail/containers/2009-June/018616.html
The 'cgroup_clone' function is removed because it is no longer used.
This is a userspace-visible change. Commit
45531757b45c ("cgroup: notify
ns_cgroup deprecated") (merged into 2.6.27) caused the kernel to emit a
printk warning users that the feature is planned for removal. Since that
time we have heard from XXX users who were affected by this.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Reviewed-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Acked-by: Matt Helsley <matthltc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Blum [Thu, 26 May 2011 23:25:21 +0000 (16:25 -0700)]
cgroups: use flex_array in attach_proc
Convert cgroup_attach_proc to use flex_array.
The cgroup_attach_proc implementation requires a pre-allocated array to
store task pointers to atomically move a thread-group, but asking for a
monolithic array with kmalloc() may be unreliable for very large groups.
Using flex_array provides the same functionality with less risk of
failure.
This is a post-patch for cgroup-procs-write.patch.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Blum [Thu, 26 May 2011 23:25:20 +0000 (16:25 -0700)]
cgroups: make procs file writable
Make procs file writable to move all threads by tgid at once.
Add functionality that enables users to move all threads in a threadgroup
at once to a cgroup by writing the tgid to the 'cgroup.procs' file. This
current implementation makes use of a per-threadgroup rwsem that's taken
for reading in the fork() path to prevent newly forking threads within the
threadgroup from "escaping" while the move is in progress.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Blum [Thu, 26 May 2011 23:25:19 +0000 (16:25 -0700)]
cgroups: add per-thread subsystem callbacks
Add cgroup subsystem callbacks for per-thread attachment in atomic contexts
Add can_attach_task(), pre_attach(), and attach_task() as new callbacks
for cgroups's subsystem interface. Unlike can_attach and attach, these
are for per-thread operations, to be called potentially many times when
attaching an entire threadgroup.
Also, the old "bool threadgroup" interface is removed, as replaced by
this. All subsystems are modified for the new interface - of note is
cpuset, which requires from/to nodemasks for attach to be globally scoped
(though per-cpuset would work too) to persist from its pre_attach to
attach_task and attach.
This is a pre-patch for cgroup-procs-writable.patch.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Blum [Thu, 26 May 2011 23:25:18 +0000 (16:25 -0700)]
cgroups: read-write lock CLONE_THREAD forking per threadgroup
Adds functionality to read/write lock CLONE_THREAD fork()ing per-threadgroup
Add an rwsem that lives in a threadgroup's signal_struct that's taken for
reading in the fork path, under CONFIG_CGROUPS. If another part of the
kernel later wants to use such a locking mechanism, the CONFIG_CGROUPS
ifdefs should be changed to a higher-up flag that CGROUPS and the other
system would both depend on.
This is a pre-patch for cgroup-procs-write.patch.
Signed-off-by: Ben Blum <bblum@andrew.cmu.edu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Reviewed-by: Paul Menage <menage@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 26 May 2011 23:25:17 +0000 (16:25 -0700)]
Documentation: configfs examples crash fix
When configfs_register_subsystem() fails, we unregister too many
subsystems in configfs_example_init. Decrement i by one to not unregister
non-registered subsystem.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wu Fengguang [Thu, 26 May 2011 23:25:16 +0000 (16:25 -0700)]
getdelays: show average CPU/IO/SWAP/RECLAIM delays
I find it very handy to show the average delays in milliseconds.
Example output (on 100 concurrent dd reading sparse files):
CPU count real total virtual total delay total delay average
986
3223509952 3207643301 38863410579 39.415ms
IO count delay total delay average
0 0 0ms
SWAP count delay total delay average
0 0 0ms
RECLAIM count delay total delay average
1059
5131834899 4ms
dd: read=0, write=0, cancelled_write=0
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Mel Gorman <mel@linux.vnet.ibm.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Reviewed-by: Satoru Moriya <satoru.moriya@hds.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 26 May 2011 23:25:15 +0000 (16:25 -0700)]
Documentation/accounting/getdelays.c: handle sendto() failures
Fixes
Documentation/accounting/getdelays.c: In function `get_family_id':
Documentation/accounting/getdelays.c:172:14: warning: variable `rc' set but not used [-Wunused-but-set-variable]
Reported-by: "Justin P. Mattock" <justinmattock@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Justin P. Mattock [Thu, 26 May 2011 23:25:14 +0000 (16:25 -0700)]
Documentation/accounting/getdelays.c: fix unused var warning
Fixes
Documentation/accounting/getdelays.c: In function `main':
Documentation/accounting/getdelays.c:436:7: warning: variable `i' set but not used [-Wunused-but-set-variable]
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nikanth Karthikesan [Thu, 26 May 2011 23:25:13 +0000 (16:25 -0700)]
Documentation/atomic_ops.txt: avoid volatile in sample code
As declaring counter as volatile is discouraged, it is best not to use it
in sample code as well.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan Carpenter [Thu, 26 May 2011 23:25:12 +0000 (16:25 -0700)]
ufs: fix truncated values handling 64 bit metadata
Originally i_lastfrag was 32 bits but then we added support for handling
64 bit metadata and it became a 64 bit variable. That was during 2007, in
54fb996ac15c "[PATCH] ufs2 write: block allocation update". Unfortunately
these casts got left behind so the value got truncated to 32 bit again.
[akpm@linux-foundation.org: remove now-unneeded min_t/max_t casting]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wolfram Sang [Thu, 26 May 2011 23:25:12 +0000 (16:25 -0700)]
drivers/rtc/rtc-mxc.c: remove defines already included in rtc.h
[akpm@linux-foundation.org: retain the code comments]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lars-Peter Clausen [Thu, 26 May 2011 23:25:10 +0000 (16:25 -0700)]
drivers/rtc/rtc-pcf50633.c: don't request update IRQ
Commit
51ba60c5 ("RTC: Cleanup rtc_class_ops->update_irq_enable()")
removed the only user of the update IRQ, so there is no need to manage it
any more.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rajeev Kumar [Thu, 26 May 2011 23:25:09 +0000 (16:25 -0700)]
rtc: add support for spear rtc
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Thu, 26 May 2011 23:25:08 +0000 (16:25 -0700)]
drivers/rtc/rtc-mrst.c: use release_mem_region after request_mem_region
The memory allocated using request_mem_region should be released using
release_mem_region, not release_region.
The semantic patch that fixes part of this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1,E2,E3;
@@
request_mem_region(E1,E2,E3)
...
?- release_region(E1,E2)
+ release_mem_region(E1,E2)
// </smpl>
[akpm@linux-foundation.org: use resource_size()]
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Voss, Nikolaus [Thu, 26 May 2011 23:25:07 +0000 (16:25 -0700)]
rtc: add basic support for ST M41T93 SPI RTC
Add basic support for ST m41t93 SPI RTCs. Tested with factory-new and
with "run-in" species with and without backup batteries.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Heiko Schocher [Thu, 26 May 2011 23:25:05 +0000 (16:25 -0700)]
rtc: add rv3029c2 RTC support
Add support for the Micro Crystal RV3029-C2 RTC chips.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Gregory Hermant <gregory.hermant@calao-systems.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Thu, 26 May 2011 23:25:04 +0000 (16:25 -0700)]
rtc: add EM3027 rtc driver
Add support for EM Microelectronic EM3027 RTC chip.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Charkov [Thu, 26 May 2011 23:25:03 +0000 (16:25 -0700)]
rtc: add support for the RTC in VIA VT8500 and compatibles
This adds a driver for the RTC devices in VIA and WonderMedia
Systems-on-Chip. Alarm, 1Hz interrupts, reading and setting time are
supported.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jesse Gross [Thu, 26 May 2011 23:25:02 +0000 (16:25 -0700)]
flex_array: avoid divisions when accessing elements
On most architectures division is an expensive operation and accessing an
element currently requires four of them. This performance penalty
effectively precludes flex arrays from being used on any kind of fast
path. However, two of these divisions can be handled at creation time and
the others can be replaced by a reciprocal divide, completely avoiding
real divisions on access.
[eparis@redhat.com: rebase on top of changes to support 0 len elements]
[eparis@redhat.com: initialize part_nr when array fits entirely in base]
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Thu, 26 May 2011 23:25:01 +0000 (16:25 -0700)]
m32r: remove redundant declaration
They have no meaning.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Thu, 26 May 2011 23:25:00 +0000 (16:25 -0700)]
m32r: fix spin_lock_irqsave() misuse
spin_lock_irqsave() requires unsigned long.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
KOSAKI Motohiro [Thu, 26 May 2011 23:24:59 +0000 (16:24 -0700)]
m32r: convert cpumask api
We plan to remove cpus_xx() old cpumask APIs later. Also, we plan to
change mm_cpu_mask() implementation, allocate only nr_cpu_ids, thus
*mm_cpu_mask() is dangerous operation.
Then, this patch convert them.
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 26 May 2011 23:24:57 +0000 (16:24 -0700)]
drivers/bcma/host_pci.c needs slab.h
alpha allmodconfig:
drivers/bcma/host_pci.c: In function 'bcma_host_pci_probe':
drivers/bcma/host_pci.c:102: error: implicit declaration of function 'kzalloc'
drivers/bcma/host_pci.c:102: warning: assignment makes pointer from integer without a cast
Cc: <zajec5@gmail.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Thu, 26 May 2011 23:24:55 +0000 (16:24 -0700)]
drivers/video/mb862xx/mb862xxfbdrv.c needs uaccess.h
alpha allmodconfig:
drivers/video/mb862xx/mb862xxfbdrv.c: In function 'mb862xxfb_ioctl':
drivers/video/mb862xx/mb862xxfbdrv.c:323: error: implicit declaration of function 'copy_to_user'
drivers/video/mb862xx/mb862xxfbdrv.c:327: error: implicit declaration of function 'copy_from_user'
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Serge E. Hallyn [Thu, 26 May 2011 20:25:05 +0000 (15:25 -0500)]
Set cred->user_ns in key_replace_session_keyring
Since this cred was not created with copy_creds(), it needs to get
initialized. Otherwise use of syscall(__NR_keyctl, KEYCTL_SESSION_TO_PARENT);
can lead to a NULL deref. Thanks to Robert for finding this.
But introduced by commit
47a150edc2a ("Cache user_ns in struct cred").
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Reported-by: Robert Święcki <robert@swiecki.net>
Cc: David Howells <dhowells@redhat.com>
Cc: stable@kernel.org (2.6.39)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 26 May 2011 20:19:00 +0000 (13:19 -0700)]
Merge branch 'trivial' of git://git./linux/kernel/git/mmarek/kbuild-2.6
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
gfs2: Drop __TIME__ usage
isdn/diva: Drop __TIME__ usage
atm: Drop __TIME__ usage
dlm: Drop __TIME__ usage
wan/pc300: Drop __TIME__ usage
parport: Drop __TIME__ usage
hdlcdrv: Drop __TIME__ usage
baycom: Drop __TIME__ usage
pmcraid: Drop __DATE__ usage
edac: Drop __DATE__ usage
rio: Drop __DATE__ usage
scsi/wd33c93: Drop __TIME__ usage
scsi/in2000: Drop __TIME__ usage
aacraid: Drop __TIME__ usage
media/cx231xx: Drop __TIME__ usage
media/radio-maxiradio: Drop __TIME__ usage
nozomi: Drop __TIME__ usage
cyclades: Drop __TIME__ usage
Linus Torvalds [Thu, 26 May 2011 19:19:31 +0000 (12:19 -0700)]
Merge branch 'x86-vdso-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: vdso: Remove unused variable
x86-64: Optimize vDSO time()
x86-64: Add time to vDSO
x86-64: Turn off -pg and turn on -foptimize-sibling-calls for vDSO
x86-64: Move vread_tsc into a new file with sensible options
x86-64: Vclock_gettime(CLOCK_MONOTONIC) can't ever see nsec < 0
x86-64: Don't generate cmov in vread_tsc
x86-64: Remove unnecessary barrier in vread_tsc
x86-64: Clean up vdso/kernel shared variables
Linus Torvalds [Thu, 26 May 2011 19:19:11 +0000 (12:19 -0700)]
Merge branches 'core-fixes-for-linus' and 'irq-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
seqlock: Get rid of SEQLOCK_UNLOCKED
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Remove smp_affinity_list when unregister irq proc
Linus Torvalds [Thu, 26 May 2011 19:14:41 +0000 (12:14 -0700)]
Merge branch 'gpio/next' of git://git.secretlab.ca/git/linux-2.6
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
gpio/via: rename VIA local config struct
basic_mmio_gpio: split into a gpio library and platform device
gpio: remove some legacy comments in build files
gpio: add trace events for setting direction and value
gpio/pca953x: Use handle_simple_irq instead of handle_edge_irq
gpiolib: export gpiochip_find
gpio: remove redundant Kconfig depends on GPIOLIB
basic_mmio_gpio: convert to non-__raw* accessors
basic_mmio_gpio: support direction registers
basic_mmio_gpio: support different input/output registers
basic_mmio_gpio: detect output method at probe time
basic_mmio_gpio: request register regions
basic_mmio_gpio: allow overriding number of gpio
basic_mmio_gpio: convert to platform_{get,set}_drvdata()
basic_mmio_gpio: remove runtime width/endianness evaluation
Linus Torvalds [Thu, 26 May 2011 19:14:20 +0000 (12:14 -0700)]
Merge branch 'for-next' of git://git./linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
Linus Torvalds [Thu, 26 May 2011 19:13:57 +0000 (12:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: Save PID of ID's owner
RDMA/cma: Add support for netlink statistics export
RDMA/cma: Pass QP type into rdma_create_id()
RDMA: Update exported headers list
RDMA/cma: Export enum cma_state in <rdma/rdma_cm.h>
RDMA/nes: Add a check for strict_strtoul()
RDMA/cxgb3: Don't post zero-byte read if endpoint is going away
RDMA/cxgb4: Use completion objects for event blocking
IB/srp: Fix integer -> pointer cast warnings
IB: Add devnode methods to cm_class and umad_class
IB/mad: Return EPROTONOSUPPORT when an RDMA device lacks the QP required
IB/uverbs: Add devnode method to set path/mode
RDMA/ucma: Add .nodename/.mode to tell userspace where to create device node
RDMA: Add netlink infrastructure
RDMA: Add error handling to ib_core_init()
Linus Torvalds [Thu, 26 May 2011 19:13:22 +0000 (12:13 -0700)]
Merge branch 'spi/next' of git://git.secretlab.ca/git/linux-2.6
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
spi/amba-pl022: work in polling or interrupt mode if pl022_dma_probe fails
spi/spi_s3c24xx: Use spi_bitbang_stop instead of spi_unregister_master in s3c24xx_spi_remove
spi/spi_nuc900: Use spi_bitbang_stop instead of spi_unregister_master in nuc900_spi_remove
spi/spi_tegra: use spi_unregister_master() instead of spi_master_put()
spi/spi_sh: use spi_unregister_master instead of spi_master_put in remove path
spi: Use void pointers for data in simple SPI I/O operations
spi/pl022: use cpu_relax in the busy loop
spi/pl022: mark driver non-experimental
spi/pl022: timeout on polled transfer v2
spi/dw_spi: improve the interrupt mode with the batch ops
spi/dw_spi: change poll mode transfer from byte ops to batch ops
spi/dw_spi: remove the un-necessary flush()
spi/dw_spi: unify the low level read/write routines
Linus Torvalds [Thu, 26 May 2011 19:11:54 +0000 (12:11 -0700)]
Merge branch 'omap-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
Linus Torvalds [Thu, 26 May 2011 19:11:17 +0000 (12:11 -0700)]
Merge branch 'merge' of git://git./linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/4xx: Adding PCIe MSI support
powerpc: Fix irq_free_virt by adjusting bounds before loop
powerpc/irq: Protect irq_radix_revmap_lookup against irq_free_virt
powerpc/irq: Check desc in handle_one_irq and expand generic_handle_irq
powerpc/irq: Always free duplicate IRQ_LEGACY hosts
powerpc/irq: Remove stale and misleading comment
powerpc/cell: Rename ipi functions to match current abstractions
powerpc/cell: Use common smp ipi actions
Remove unused MSG_ flags in linux/smp.h
powerpc/pseries: Update MAX_HCALL_OPCODE to reflect page coalescing
powerpc/oprofile: Handle events that raise an exception without overflowing
powerpc/ftrace: Implement raw syscall tracepoints on PowerPC
Linus Torvalds [Thu, 26 May 2011 19:03:50 +0000 (12:03 -0700)]
Fix build with !HUGETLBFS
I stupidly broke the case of CONFIG_HUGETLBFS=n when doing the
conversion to vm_flags_t in commit
ca16d140af91 ("mm: don't access
vm_flags as 'int'"). And my 'allyesconfig' build didn't find it, for
obvious reasons..
Include <linux/mm_types.h> in <linux/hugetlb.h>. The problem could have
been avoided by just turning the hugetlb_file_setup() error wrapper into
a macro, but mm_types.h is a reasonable include in this file.
Reported-by: Richard -rw- Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 26 May 2011 17:55:15 +0000 (10:55 -0700)]
Merge branch 'linux-next' of git://git./linux/kernel/git/jlbec/ocfs2
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2: (28 commits)
Ocfs2: Teach local-mounted ocfs2 to handle unwritten_extents correctly.
ocfs2/dlm: Do not migrate resource to a node that is leaving the domain
ocfs2/dlm: Add new dlm message DLM_BEGIN_EXIT_DOMAIN_MSG
Ocfs2/move_extents: Set several trivial constraints for threshold.
Ocfs2/move_extents: Let defrag handle partial extent moving.
Ocfs2/move_extents: move/defrag extents within a certain range.
Ocfs2/move_extents: helper to calculate the defraging length in one run.
Ocfs2/move_extents: move entire/partial extent.
Ocfs2/move_extents: helpers to update the group descriptor and global bitmap inode.
Ocfs2/move_extents: helper to probe a proper region to move in an alloc group.
Ocfs2/move_extents: helper to validate and adjust moving goal.
Ocfs2/move_extents: find the victim alloc group, where the given #blk fits.
Ocfs2/move_extents: defrag a range of extent.
Ocfs2/move_extents: move a range of extent.
Ocfs2/move_extents: lock allocators and reserve metadata blocks and data clusters for extents moving.
Ocfs2/move_extents: Add basic framework and source files for extent moving.
Ocfs2/move_extents: Adding new ioctl code 'OCFS2_IOC_MOVE_EXT' to ocfs2.
Ocfs2/refcounttree: Publicize couple of funcs from refcounttree.c
Ocfs2: Add a new code 'OCFS2_INFO_FREEFRAG' for o2info ioctl.
Ocfs2: Add a new code 'OCFS2_INFO_FREEINODE' for o2info ioctl.
...
Linus Torvalds [Thu, 26 May 2011 17:50:56 +0000 (10:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/djm/tmem
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/djm/tmem:
xen: cleancache shim to Xen Transcendent Memory
ocfs2: add cleancache support
ext4: add cleancache support
btrfs: add cleancache support
ext3: add cleancache support
mm/fs: add hooks to support cleancache
mm: cleancache core ops functions and config
fs: add field to superblock to support cleancache
mm/fs: cleancache documentation
Fix up trivial conflict in fs/btrfs/extent_io.c due to includes
Linus Torvalds [Thu, 26 May 2011 17:49:11 +0000 (10:49 -0700)]
Merge branch 'for-linus' of git://oss.sgi.com/xfs/xfs
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: correctly decrement the extent buffer index in xfs_bmap_del_extent
xfs: check for valid indices in xfs_iext_get_ext and xfs_iext_idx_to_irec
xfs: fix up asserts in xfs_iflush_fork
xfs: do not do pointer arithmetic on extent records
xfs: do not use unchecked extent indices in xfs_bunmapi
xfs: do not use unchecked extent indices in xfs_bmapi
xfs: do not use unchecked extent indices in xfs_bmap_add_extent_*
xfs: remove if_lastex
xfs: remove the unused XFS_BMAPI_RSVBLOCKS flag
xfs: do not discard alloc btree blocks
xfs: add online discard support
Randy Dunlap [Thu, 26 May 2011 17:16:15 +0000 (10:16 -0700)]
regulator: Fix 88pm8607.c printk format warning
Fix printk format warning (seen on x86_64) and change to unsigned
output format:
drivers/regulator/88pm8607.c:417: warning: format '%d' expects type 'int', but argument 3 has type 'resource_size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Trilok Soni [Fri, 13 May 2011 09:47:51 +0000 (15:17 +0530)]
input: Add support for Qualcomm PMIC8XXX power key
Add support for PMIC8XXX power key driven over dedicated
KYPD_PWR_N pin.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Trilok Soni [Thu, 19 May 2011 05:24:04 +0000 (10:54 +0530)]
input: Add Qualcomm pm8xxx keypad controller driver
Add Qualcomm PMIC8XXX based keypad controller driver
supporting upto 18x8 matrix configuration.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
git.openpandora.org / pandora-kernel.git / log