[PATCH] skge: version 1.6

Update version string.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] skge: dont allow bad hardware address from ROM

Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] skge: transmit complete via IRQ not NAPI

The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] skge: TX low water mark definition

Consolidate all usage of ring low water mark to one value.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] skge: use workq for PHY handling

Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] myri10ge update

The following patch updates the myri10ge to 1.0.0, with the following changes:
* Switch to dma_alloc_coherent API.
* Avoid PCI burst when writing the firmware on chipset with unaligned completions.
* Use ethtool_op_set_tx_hw_csum instead of ethtool_op_set_tx_csum.
* Include linux/dma-mapping.h to bring DMA_32/64BIT_MASK on all architectures
  (was missing at least on alpha).
* Some typo and warning fixes.

Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
 drivers/net/myri10ge/myri10ge.c |   57 +++++++++++++++++++-----------
 1 file changed, 37 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Merge branch 'master' into upstream

[DOC] Update bonding documentation with sysfs info

Bonding documentation needed an update to include sysfs specific
information. This patch adds information on how to change bonding
parameters at runtime using the sysfs interface.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

[ARM] Fix Neponset IRQ handling

While testing the genirq code on ARM, a condition was found whereby
the Neponset IRQ handler was being re-entered, causing the system
to deadlock.

Under the ARM IRQ code, this would not have been a visible problem
because the "simple" IRQ handling had no re-entrancy protection.

Resolve this by acknowledging the parent interrupt after we mask it
when we are going to handle one of our "special" level-based sources
(from ethernet or USAR chip.)

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

e1000: add PCI Error Recovery

Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.

Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

e100: add PCI Error Recovery

Various PCI bus errors can be signaled by newer PCI controllers.  This
patch adds the PCI error recovery callbacks to the intel ethernet e100
device driver. The patch has been tested, and appears to work well.

Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

e1000: remove risky prefetch on next_skb->data

It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures.  Remove them for now.  We'll let them
stay in mm for a while, or find a better solution to enable.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

e1000: fix ethtool test irq alloc as "probe"

New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.

This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>

Removed hard coded EDID buffer size.

Signed-off-by: Dennis Munsie <dmunsie@cecropia.com>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>

Linux 2.6.17-rc6

Merge /pub/scm/linux/kernel/git/davem/net-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [BRIDGE]: fix locking and memory leak in br_add_bridge
  [IRDA]: Missing allocation result check in irlap_change_speed().
  [PPPOE]: Missing result check in __pppoe_xmit().
  [NET]: Eliminate unused /proc/sys/net/ethernet
  [NETCONSOLE]: Clean up initcall warning.
  [TCP]: Avoid skb_pull if possible when trimming head

[BRIDGE]: fix locking and memory leak in br_add_bridge

There are several bugs in error handling in br_add_bridge:
- when dev_alloc_name fails, allocated net_device is not freed
- unregister_netdev is called when rtnl lock is held
- free_netdev is called before netdev_run_todo has a chance to be run after
  unregistering net_device

Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge master.kernel.org:/home/rmk/linux-2.6-serial

* master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] typo: buad -> baud

Merge master.kernel.org:/home/rmk/linux-2.6-mmc

* master.kernel.org:/home/rmk/linux-2.6-mmc:
  [MMC] Prevent au1xmmc.c breakage on non-Au1200 Alchemy
  [MMC] Add maintainers entry for MMC subsystem

Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3543/1: [Fwd: PXA270 bootparams address not set]
  [ARM] Trivial typo fixes

[MIPS] Fix sparsemem support.

Move memory_present() in arch/mips/kernel/setup.c. When using sparsemem
extreme, this function does an allocate for bootmem. This would always
fail since init_bootmem hasn't been called yet.

Move memory_present after free_bootmem. This only marks actual memory
ranges as present instead of the entire address space.

Signed-off-by: Chad Reese <creese@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix compiler warnings (field width, unused variable)

Fix following warnings:
linux/arch/mips/kernel/setup.c:432: warning: field width is not type int (arg 2)
linux/arch/mips/kernel/setup.c:432: warning: field width is not type int (arg 4)
linux/arch/mips/kernel/syscall.c:279: warning: unused variable `len'
linux/arch/mips/kernel/syscall.c:280: warning: unused variable `name'
linux/arch/mips/math-emu/dp_fint.c:32: warning: unused variable `xc'
linux/arch/mips/math-emu/dp_flong.c:32: warning: unused variable `xc'
linux/arch/mips/math-emu/sp_fint.c:32: warning: unused variable `xc'
linux/arch/mips/math-emu/sp_flong.c:32: warning: unused variable `xc'

(original patch by Atsushi, slight changes to the setup.c part by me.)

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix sparse warnings about too big constants.

Fix following warnings:
linux/arch/mips/kernel/setup.c:249:12: warning: constant 0xffffffff00000000 is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:209:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:227:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:283:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:299:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix 64-bit build for RM7000.

RM7000 has 40-bit virtual / 36-bit physical address space.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] IP32: Fix warnings.

The expressions are volatile; no need for temporary variables.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix non-linear memory mapping on MIPS

Fix the non-linear memory mapping done via remap_file_pages() -- it
didn't work on any MIPS CPU because the page offset clashing with
_PAGE_FILE and some other page protection bits which should have been left
zeros for this kind of pages.

Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] SB1: Only pass1 FPUs are broken beyond recovery.

The wrong revision number in the check was forcing a fallback to FPU
emulation for all SB1 cores in 2.6.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] open() forces O_LARGEFILE for o32 on 64bit kernels

open() always sets the O_LARGEFILE flag for the o32 ABI implementation
of a 64bit kernel. The appended patch fixes it.

Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Au1xx0: fix prom_getenv() to handle YAMON style environment

Alchemy boards use YAMON which passes the environment variables as the
tuples of strings (the name followed by the value) unlike PMON which
passes "name=<val>" strings.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix swap entry for MIPS32 36-bit physical address

With 64-bit physical address enabled, 'swapon' was causing kernel oops on
Alchemy CPUs (MIPS32) because of the swap entry type field corrupting the
_PAGE_FILE bit in 'pte_low' field. So, switch to storing the swap entry in
'pte_high' field using all its bits except _PAGE_GLOBAL and _PAGE_VALID which
gives 25 bits for the swap entry offset.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix mprotect() syscall for MIPS32 w/36-bit physical address support

Fix mprotect() syscall for MIPS32 CPUs with 36-bit physical address
support: pte_modify() macro didn't clear the hardware page protection bits
before modifying...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Save write-only Config.OD from being clobbered

Save the Config.OD bit from being clobbered by coherency_setup(). This
bit, when set, fixes various errata in the early steppings of Au1x00
SOCs.  Unfortunately, the bit was write-only on the most early of them.
In addition, also restore the bit after a wakeup from sleep.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Print more information if we're struck by a machine check exception.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix declaration of smp_prepare_cpus() platform hook.

A while ago prom_prepare_cpus was replaced by plat_prepare_cpus but
the declaration has stayed unchanged.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix modpost warning: Rename op_model_xxx to op_model_xxx_ops.

The modpost uses a whitelist for commonly used suffix on checking the
section mismatch.  Adding "_ops" suffix to op_modex_xxx get rid of
this modpost warning.

WARNING: arch/mips/oprofile/oprofile.o - Section mismatch: reference to .init.text: from .data after 'op_model_mipsxx' (at offset 0x528)

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix instable BogoMIPS on multi-issue processors.

Increase alignment of BogoMIPS loop to 8 bytes.  Having the delay loop
overlap cache line boundaries may cause instable delays.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Ignore unresolved weak symbols in modules.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Fix SMP now that fixup_cpu_present_map is gone.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[MIPS] Remove duplicate declaration of cpu_online_map.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

[IRDA]: Missing allocation result check in irlap_change_speed().

The skb allocation may fail, which can result in a NULL pointer dereference
in irlap_queue_xmit().

Coverity CID: 434.

Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PPPOE]: Missing result check in __pppoe_xmit().

skb_clone() may fail, we should check the result.

Coverity CID: 1215.

Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NET]: Eliminate unused /proc/sys/net/ethernet

The /proc/sys/net/ethernet directory has been sitting empty for more than
10 years!  Time to eliminate it!

Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[NETCONSOLE]: Clean up initcall warning.

From: Matt Mackall <mpm@selenic.com>

netconsole is being wrong here.  If it wasn't enabled there's no error.

Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[TCP]: Avoid skb_pull if possible when trimming head

Trimming the head of an skb by calling skb_pull can cause the packet
to become unaligned if the length pulled is odd.  Since the length is
entirely arbitrary for a FIN packet carrying data, this is actually
quite common.

Unaligned data is not the end of the world, but we should avoid it if
it's easily done.  In this case it is trivial.  Since we're discarding
all of the head data it doesn't matter whether we move skb->data forward
or back.

However, it is still possible to have unaligned skb->data in general.
So network drivers should be prepared to handle it instead of crashing.

This patch also adds an unlikely marking on len < headlen since partial
ACKs on head data are extremely rare in the wild.  As the return value
of __pskb_trim_head is no longer ever NULL that has been removed.

Signed-off-by: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] wireless: move zd1201 where it belongs

zd1201 is wifi adapter, yet it is hiding in drivers/usb/net where
noone can find it. This moves Kconfig/Makefile zd1201 to the right
place.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] bcm43xx: quiet down log spam from set_security

The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.

Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] softmac: unified capabilities computation

This patch moves the capabilities field computation to a function for clarity
and adds some previously unimplemented bits.

Signed off by Joseph Jezak <josejx@gentoo.org>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-By: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] softmac: Fix handling of authentication failure

My router blew up earlier, but exhibited some interesting behaviour during
its dying moments. It was broadcasting beacons but wouldn't respond to
any authentication requests.

I noticed that softmac wasn't playing nice with this, as I couldn't make it try
to connect to other networks after it had timed out authenticating to my ill
router.

To resolve this, I modified the softmac event/notify API to pass the event
code to the callback, so that callbacks being notified from
IEEE80211SOFTMAC_EVENT_ANY masks can make some judgement. In this case, the
ieee80211softmac_assoc callback needs to make a decision based upon whether
the association passed or failed.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] softmac: complete shared key authentication

This patch finishes of the partially-complete shared key authentication
implementation in softmac.

The complication here is that we need to encrypt a management frame during
the authentication process. I don't think there are any other scenarios where
this would have to happen.

To get around this without causing too many headaches, we decided to just use
software encryption for this frame. The softmac config option now selects
IEEE80211_CRYPT_WEP so that we can ensure this available. This also involved
a modification to some otherwise unused ieee80211 API.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] ieee80211softmac_io.c: fix warning "defined but not used"

Got this compiler warning and Johannes Berg <johannes@sipsolutions.net>
wrote:

Yeah, known 'bug', we have that code there but never use it. Feel free
to submit a patch (to John Linville, CC netdev and softmac-dev) to
remove it.

Signed-off-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] usb wifi: zd1201 cleanups

Cleanup coding style and other small stuff in zd1201. No real code
changes.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'upstream-fixes' into upstream

Merge /linux/kernel/git/brodo/pcmcia-fixes-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
  [PATCH] pcmcia: fix zeroing of cm4000_cs.c data
  [PATCH] pcmcia: missing pcmcia_get_socket() result check

[PATCH] uml: add -ffreestanding to CFLAGS

From: Jeff Dike <jdike@addtoit.com>

This fixes the undefined reference to strcpy seen when building modules on
i386.  Tracked down by Al Viro.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: more __user annotations

From: Al Viro <viro@zeniv.linux.org.uk>

uml __user annotations

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: __user annotation in arch_prctl

From: Al Viro <viro@zeniv.linux.org.uk>

fix uml/amd64 prctl()

put_user() there should go to (long __user *)addr, not &addr

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: fix a typo in do_uml_initcalls

From: Jeff Dike <jdike@addtoit.com>

We had a spurious semicolon somehow.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: fix wall_to_monotonic initialization

From: Jeff Dike <jdike@addtoit.com>

Initialize wall_to_monotonic correctly.  This fixes a problem where sleeps
lasted about one secone less than they should.  This also called for a bit of
code restructuring, following a patch which Blaisorblade had been keeping.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] uml: add asm/irqflags.h

From: Jeff Dike <jdike@addtoit.com>

Add an empty asm/irqflags.h, which seems to satisfy the lock validator enough
that UML builds.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] m48t86: ia64 build fix

From: Andrew Morton <akpm@osdl.org>

drivers/rtc/rtc-m48t86.c: In function `m48t86_rtc_read_time':
drivers/rtc/rtc-m48t86.c:51: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:55: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:56: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:57: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:58: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:60: error: structure has no member named `ia64_mv'

readb() and writeb() are macros on ia64.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sata_sil24: SII3124 sata driver endian problem

From: "Rune Torgersen" <runet@innovsys.com>

Fix an endian issue in the sil24 driver.

Signed-off-by: Rune Torgersen <runet@innovsys.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] sbp2: fix check of return value of hpsb_allocate_and_register_addrspace()

From: Stefan Richter <stefanr@s5r6.in-berlin.de>

I added a failure check in patch "sbp2: variable status FIFO address (fix
login timeout)" --- alas for a wrong error value.  This is a bug since
Linux 2.6.16.  Leads to NULL pointer dereference if the call failed, and
bogus failure handling if call succeeded.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
Cc: Ben Collins <bcollins@debian.org>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] MAINTAINERS: Add entries for BNX2 and TG3

From: "Michael Chan" <mchan@broadcom.com>

Add maintainer entries for Broadcom BNX2 and TG3 drivers.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Implement get / set tso for forcedeth driver

From: Zachary Amsden <zach@vmware.com>

Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] pmf_register_irq_client() gives sleep with locks held warning

From: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This fixes request_irq() potentially called from atomic context.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] fs/namei.c: Call to file_permission() under a spinlock in do_lookup_path()

From: Trond Myklebust <Trond.Myklebust@netapp.com>

We're presently running lock_kernel() under fs_lock via nfs's ->permission
handler.  That's a ranking bug and sometimes a sleep-in-spinlock bug.  This
problem was introduced in the openat() patchset.

We should not need to hold the current->fs->lock for a codepath that doesn't
use current->fs.

[vsu@altlinux.ru: fix error path]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] alpha: SMP IRQ routing fix

From: Ivan Kokshaysky <ink@jurassic.park.msu.ru>

After removal of fixup_cpu_present_map() function Alpha ended up with an empty
cpu_present_map, so secondary CPUs on SMP systems are not being started.

Worse, on some platforms we route interrupts to secondary CPUs using
cpu_possible_map which is still populated properly.  As a result, these
interrupts go nowhere so the machines like DP264 aren't able to boot even with
a primary CPU.

Fixed basically by s/cpu_present_mask/cpu_present_map/.

Thanks to Ernst Herzberg for reporting the bug and testing the fix.

Cc: Ernst Herzberg <list-lkml@net4u.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] selinux: fix sb_lock/sb_security_lock nesting

From: Stephen Smalley <sds@tycho.nsa.gov>

Fix unsafe nesting of sb_lock inside sb_security_lock in
selinux_complete_init.  Detected by the kernel locking validator.

Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] Sparsemem build fix

From: Ralf Baechle <ralf@linux-mips.org>

<linux/mmzone.h> uses PAGE_SIZE, PAGE_SHIFT from <asm/page.h> without
including that header itself.  For some sparsemem configurations this may
result in build errors like:

  CC      init/initramfs.o
In file included from include/linux/gfp.h:4,
                 from include/linux/slab.h:15,
                 from include/linux/percpu.h:4,
                 from include/linux/rcupdate.h:41,
                 from include/linux/dcache.h:10,
                 from include/linux/fs.h:226,
                 from init/initramfs.c:2:
include/linux/mmzone.h:498:22: warning: "PAGE_SHIFT" is not defined
In file included from include/linux/gfp.h:4,
                 from include/linux/slab.h:15,
                 from include/linux/percpu.h:4,
                 from include/linux/rcupdate.h:41,
                 from include/linux/dcache.h:10,
                 from include/linux/fs.h:226,
                 from init/initramfs.c:2:
include/linux/mmzone.h:526: error: `PAGE_SIZE' undeclared here (not in a function)
include/linux/mmzone.h: In function `__pfn_to_section':
include/linux/mmzone.h:573: error: `PAGE_SHIFT' undeclared (first use in this function)
include/linux/mmzone.h:573: error: (Each undeclared identifier is reported only once
include/linux/mmzone.h:573: error: for each function it appears in.)
include/linux/mmzone.h: In function `pfn_valid':
include/linux/mmzone.h:578: error: `PAGE_SHIFT' undeclared (first use in this function)
make[1]: *** [init/initramfs.o] Error 1
make: *** [init] Error 2

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Seems-reasonable-to: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s390: cio non-unique path group ids

From: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>

The path grouping can fail due to non-unique pathgroup-IDs.  The source for
the CPU-ID part of the ID was incorrectly specified on 64 bit systems.
Additionally, the length of the ID was too large due to incorrect data packing
declaration.  Fix CPU-ID lowcore address and add missing packing declaration.

Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] s390: irb memcpy argument swap

From: Cornelia Huck <cornelia.huck@de.ibm.com>

Swapped memcpy arguments in ccw_device_irq() when doing basic sense after
unsolicited interrupt.

Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] nmclan_cs: dereferencing skb after netif_rx()

From: Florin Malita <fmalita@gmail.com>

The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats.  'pkt_len' should work instead.

Coverity CID: 911.

Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[PATCH] bcm43xx: add DMA rx poll workaround to DMA4

Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[CPUFREQ] sets nforce2 minimum PLL divider to 2.

Sets minimum PLL divider to 2.
No negative impact when tested with two nForce2 based boards.

Alexander Choporov reported (06/01/06) that xdiv = 1 does not work on his
Abit NF7S2. Although there shouldn't be much cases that lead to xdiv = 1.

(Updates also the (C) year)

Signed-off-by: Sebastian Witt <se.witt@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Fix missing fold at end of checksums.

[ARM] 3543/1: [Fwd: PXA270 bootparams address not set]

Patch from Steve Yang

MACHINE_START struct doesn't have any bootargs location for the
mainstone. Result is no kernel command args get passed; no serial driver
is selected for console and results in a silent boot failure.

Signed-off-by: Steve Yang <steve.yang@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'from-linus' into upstream

[CPUFREQ] Make powernow-k7 work on SMP kernels.
Even though powernow-k7 doesn't work in SMP environments,
it can work on an SMP configured kernel if there's only
one CPU present, however recalibrate_cpu_khz was returning
-EINVAL on such kernels, so we failed to init the cpufreq driver.

Signed-off-by: Dave Jones <davej@redhat.com>

IPoIB: Fix AH leak at interface down

When ipoib_stop() is called it first calls netif_stop_queue() to stop
the kernel from passing more packets to the network driver. However,
the completion handler may call netif_wake_queue() re-enabling packet
transfer.

This might result in leaks (we see AH leaks which we think can be
attributed to this bug) as new packets get posted while the interface
is going down.

Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

[SERIAL] typo: buad -> baud

Replacing mistyped "buad" with "baud" where applicable.

Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[SPARC64]: Fix missing fold at end of checksums.

Both csum_partial() and the csum_partial_copy*() family of routines
forget to do a final fold on the computed checksum value on sparc64.
So do the standard Sparc "add + set condition codes, add carry"
sequence, then make sure the high 32-bits of the return value are
clear.

Based upon some excellent detective work and debugging done by
Richard Braun and Samuel Thibault.

Signed-off-by: David S. Miller <davem@davemloft.net>

[CPUFREQ] cpufreq core {d,}printk adjustments

Remove KERN_* suffixes from some cpufreq driver's dprintk-s.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>

[CPUFREQ] dprintk adjustments to cpufreq-speedstep-centrino

Remove KERN_* suffixes from some Centrino cpufreq driver's dprintk-s.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>

[CPUFREQ] dprintk adjustments to cpufreq-nforce2

Remove KERN_* suffixes from some NForce2 cpufreq driver's dprintk-s.

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>

[CPUFREQ] Prepare powernow-k8 for future CPUs.

Forthcoming AMD products will use a different algorithm for transitioning
pstates than the current generation Opteron products do.  The attached
patch allows the powernow-k8 driver to work with those products.

Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>

[ARM] Trivial typo fixes

Trivial typo fixes in Kconfig files (ARM).

Signed-off-by: Egry Gabor <gaboregry@t-online.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] Prevent au1xmmc.c breakage on non-Au1200 Alchemy

The driver is selectable on other than Au1200 Alchemy systems but won't
build nor work - there is no MMC hw.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[MMC] Add maintainers entry for MMC subsystem

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Merge /linux/kernel/git/jejb/scsi-rc-fixes-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] scsi_lib.c: properly count the number of pages in scsi_req_map_sg()
  [SCSI] scsi_transport_sas: make write attrs writeable
  [SCSI] scsi_transport_sas; fix user_scan
  [SCSI] ppa: fix for machines with highmem
  [SCSI] mptspi: reset handler shouldn't be called for other bus protocols
  [SCSI] Blacklist entry for HP dat changer

[TCP] tcp_highspeed: Fix problem observed by Xiaoliang (David) Wei

When snd_cwnd is smaller than 38 and the connection is in
congestion avoidance phase (snd_cwnd > snd_ssthresh), the snd_cwnd
seems to stop growing.

The additive increase was confused because C array's are 0 based.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge master.kernel.org:/home/rmk/linux-2.6-serial

* master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] Update parity handling documentation

Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 3540/1: ixp23xx: deal with gap in interrupt bitmasks
  [ARM] 3539/1: ixp23xx: fix __arch_ixp23xx_is_coherent() for A1 stepping

Merge /pub/scm/linux/kernel/git/davem/sparc-2.6

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Fix D-cache corruption in mremap
  [SPARC64]: Make smp_processor_id() functional before start_kernel()

[ARM] 3540/1: ixp23xx: deal with gap in interrupt bitmasks

Patch from Lennert Buytenhek

On the ixp23xx, the microengine thread interrupt sources are numbered
56..119, but their mask/status bits are located in bit positions 64..127
in the various registers in the interrupt controller (bit positions
56..63 are unused.)

We don't deal with this, so currently, when asked to enable IRQ 64, we
will enable IRQ 56 instead.

The only interrupts >= 64 are the thread interrupt sources, and there
are no in-tree users of those yet, so this is fortunately not a big
problem, but this needs fixing anyway.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[ARM] 3539/1: ixp23xx: fix __arch_ixp23xx_is_coherent() for A1 stepping

Patch from Lennert Buytenhek

The current __ixp23xx_arch_is_coherent() check assumes that the
lower byte of IXP23XX_PRODUCT_ID is identical to the lower byte of
processor_id, but this is not the case, and because of this we were
incorrectly enabling coherency on A1 stepping CPUs.

Stepping A1 of the ixp2350, which has a PRODUCT_ID of 0x401, has '02'
in the lower byte of processor_id, while A2, with a PRODUCT_ID of
0x402, has '04' in the lower byte of processor_id.

So, to check for >= A2, we really need to check the lower byte of
processor_id against >= 4.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[PATCH] slab.c: fix offslab_limit bug

mm/slab.c's offlab_limit logic is totally broken.

Firstly, "offslab_limit" is a global variable while it should either be
calculated in situ or should be passed in as a parameter.

Secondly, the more serious problem with it is that the condition for
calculating it:

               if (!(OFF_SLAB(sizes->cs_cachep))) {
                       offslab_limit = sizes->cs_size - sizeof(struct slab);
                       offslab_limit /= sizeof(kmem_bufctl_t);

is in total disconnect with the condition that makes use of it:

               /* More than offslab_limit objects will cause problems */
               if ((flags & CFLGS_OFF_SLAB) && num > offslab_limit)
                       break;

but due to offslab_limit being a global variable this breakage was
hidden.

Up until lockdep came along and perturbed the slab sizes sufficiently so
that the first off-slab cache would still see a (non-calculated) zero
value for offslab_limit and would panic with:

  kmem_cache_create: couldn't create cache size-512.

  Call Trace:
   [<ffffffff8020a5b9>] show_trace+0x96/0x1c8
   [<ffffffff8020a8f0>] dump_stack+0x13/0x15
   [<ffffffff8022994f>] panic+0x39/0x21a
   [<ffffffff80270814>] kmem_cache_create+0x5a0/0x5d0
   [<ffffffff80aced62>] kmem_cache_init+0x193/0x379
   [<ffffffff80abf779>] start_kernel+0x17f/0x218
   [<ffffffff80abf263>] _sinittext+0x263/0x26a

  Kernel panic - not syncing: kmem_cache_create(): failed to create slab `size-512'

Paolo Ornati's config on x86_64 managed to trigger it.

The fix is to move the calculation to the place that makes use of it.
This also makes slab.o 54 bytes smaller.

Btw., the check itself is quite silly. Its intention is to test whether
the number of objects per slab would be higher than the number of slab
control pointers possible. In theory it could be triggered: if someone
tried to allocate 4-byte objects cache and explicitly requested with
CFLGS_OFF_SLAB. So i kept the check.

Out of historic interest i checked how old this bug was and it's
ancient, 10 years old! It is the oldest hidden and then truly triggering
bugs i ever saw being fixed in the kernel!

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

[SERIAL] Update parity handling documentation

Update documentation to match reality. INPCK controls whether input
parity checking is enabled.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

[SPARC64]: Fix D-cache corruption in mremap

If we move a mapping from one virtual address to another,
and this changes the virtual color of the mapping to those
pages, we can see corrupt data due to D-cache aliasing.

Check for and deal with this by overriding the move_pte()
macro.  Set things up so that other platforms can cleanly
override the move_pte() macro too.

Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] pcmcia: fix zeroing of cm4000_cs.c data

Fix the incorrect calculation of how much to zero out in struct cm4000_dev
on device initialization.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>

[PATCH] pcmcia: missing pcmcia_get_socket() result check

The result of pcmcia_get_socket() may be NULL but ds_event() uses it
without checking.

Coverity CID: 436.

Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>