pandora-kernel.git
10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394...
Linus Torvalds [Tue, 1 Nov 2011 22:02:38 +0000 (15:02 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: ohci: fix isochronous DMA synchronization
  firewire: ohci: work around selfID junk due to wrong gap count
  firewire: net: Use posted writes
  firewire: use clamp and min3 macros
  firewire: ohci: optimize TSB41BA3D detection
  firewire: ohci: TSB41BA3D support tweaks
  firewire: ohci: Add support for TSB41BA3D phy
  firewire: ohci: Move code from the bus reset tasklet into a workqueue
  firewire: sbp2: fold two functions into one
  firewire: sbp2: move some code to more sensible places
  firewire: sbp2: remove obsolete reference counting

10 years agoMerge branch 'pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Linus Torvalds [Tue, 1 Nov 2011 17:52:29 +0000 (10:52 -0700)]
Merge branch 'pstore' of git://git./linux/kernel/git/aegl/linux

* 'pstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  pstore: make pstore write function return normal success/fail value
  pstore: change mutex locking to spin_locks
  pstore: defer inserting OOPS entries into pstore

10 years agoMerge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland...
Linus Torvalds [Tue, 1 Nov 2011 17:51:38 +0000 (10:51 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
  mlx4_core: Deprecate log_num_vlan module param
  IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
  IB/mlx4: Enable 4K mtu for IBoE
  RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
  RDMA/cxgb4: Serialize calls to CQ's comp_handler
  RDMA/cxgb3: Serialize calls to CQ's comp_handler
  IB/qib: Fix issue with link states and QSFP cables
  IB/mlx4: Configure extended active speeds
  mlx4_core: Add extended port capabilities support
  IB/qib: Hold links until tuning data is available
  IB/qib: Clean up checkpatch issue
  IB/qib: Remove s_lock around header validation
  IB/qib: Precompute timeout jiffies to optimize latency
  IB/qib: Use RCU for qpn lookup
  IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
  IB/qib: Decode path MTU optimization
  IB/qib: Optimize RC/UC code by IB operation
  IPoIB: Use the right function to do DMA unmap pages
  RDMA/cxgb4: Use correct QID in insert_recv_cqe()
  RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
  ...

10 years agoMerge branches 'amso1100', 'cma', 'cxgb3', 'cxgb4', 'fdr', 'ipath', 'ipoib', 'misc...
Roland Dreier [Tue, 1 Nov 2011 16:37:08 +0000 (09:37 -0700)]
Merge branches 'amso1100', 'cma', 'cxgb3', 'cxgb4', 'fdr', 'ipath', 'ipoib', 'misc', 'mlx4', 'misc', 'nes', 'qib' and 'xrc' into for-next

10 years agoMerge git://github.com/herbertx/crypto
Linus Torvalds [Tue, 1 Nov 2011 16:24:41 +0000 (09:24 -0700)]
Merge git://github.com/herbertx/crypto

* git://github.com/herbertx/crypto: (48 commits)
  crypto: user - Depend on NET instead of selecting it
  crypto: user - Add dependency on NET
  crypto: talitos - handle descriptor not found in error path
  crypto: user - Initialise match in crypto_alg_match
  crypto: testmgr - add twofish tests
  crypto: testmgr - add blowfish test-vectors
  crypto: Make hifn_795x build depend on !ARCH_DMA_ADDR_T_64BIT
  crypto: twofish-x86_64-3way - fix ctr blocksize to 1
  crypto: blowfish-x86_64 - fix ctr blocksize to 1
  crypto: whirlpool - count rounds from 0
  crypto: Add userspace report for compress type algorithms
  crypto: Add userspace report for cipher type algorithms
  crypto: Add userspace report for rng type algorithms
  crypto: Add userspace report for pcompress type algorithms
  crypto: Add userspace report for nivaead type algorithms
  crypto: Add userspace report for aead type algorithms
  crypto: Add userspace report for givcipher type algorithms
  crypto: Add userspace report for ablkcipher type algorithms
  crypto: Add userspace report for blkcipher type algorithms
  crypto: Add userspace report for ahash type algorithms
  ...

10 years agosysfs: Make sysfs_rename safe with sysfs_dirents in rbtrees.
Eric W. Biederman [Tue, 1 Nov 2011 14:06:17 +0000 (07:06 -0700)]
sysfs: Make sysfs_rename safe with sysfs_dirents in rbtrees.

In sysfs_rename we need to remove the optimization of not calling
sysfs_unlink_sibling and sysfs_link_sibling if the renamed parent
directory is not changing.  This optimization is no longer valid now
that sysfs dirents are stored in an rbtree sorted by name.

Move the assignment of s_ns before the call of sysfs_link_sibling.  With
no sysfs_dirent fields changing after the call of sysfs_link_sibling
this allows sysfs_link_sibling to take any of the directory entries into
account when it builds the rbtrees, and s_ns looks like a prime canidate
to be used in the rbtree in the future.

Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Greg KH <gregkh@suse.de>
Cc: David Miller <davem@davemloft.net>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoMerge Qualcom Hexagon architecture
Linus Torvalds [Tue, 1 Nov 2011 14:48:13 +0000 (07:48 -0700)]
Merge Qualcom Hexagon architecture

This is the fifth version of the patchset (with one tiny whitespace fix)
to the Linux kernel to support the Qualcomm Hexagon architecture.

Between now and the next pull requests, Richard Kuo should have his key
signed, etc., and should be back on kernel.org.  In the meantime, this
got merged as a emailed patch-series.

* Hexagon: (36 commits)
  Add extra arch overrides to asm-generic/checksum.h
  Hexagon: Add self to MAINTAINERS
  Hexagon: Add basic stacktrace functionality for Hexagon architecture.
  Hexagon: Add configuration and makefiles for the Hexagon architecture.
  Hexagon: Comet platform support
  Hexagon: kgdb support files
  Hexagon: Add page-fault support.
  Hexagon: Add page table header files & etc.
  Hexagon: Add ioremap support
  Hexagon: Provide DMA implementation
  Hexagon: Implement basic TLB management routines for Hexagon.
  Hexagon: Implement basic cache-flush support
  Hexagon: Provide basic implementation and/or stubs for I/O routines.
  Hexagon: Add user access functions
  Hexagon: Add locking types and functions
  Hexagon: Add SMP support
  Hexagon: Provide basic debugging and system trap support.
  Hexagon: Add ptrace support
  Hexagon: Add time and timer functions
  Hexagon: Add interrupts
  ...

10 years agoAdd extra arch overrides to asm-generic/checksum.h
Linas Vepstas [Mon, 31 Oct 2011 23:56:59 +0000 (18:56 -0500)]
Add extra arch overrides to asm-generic/checksum.h

There are plausible reasons for architectures to provide their own
versions of csum_partial_copy_nocheck and csum_tcpudp_magic.
By protecting these, the architecture can still re-use the
asm-generic checksum.h, instead of copying it.

Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add self to MAINTAINERS
Richard Kuo [Mon, 31 Oct 2011 23:56:38 +0000 (18:56 -0500)]
Hexagon: Add self to MAINTAINERS

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add basic stacktrace functionality for Hexagon architecture.
Richard Kuo [Mon, 31 Oct 2011 23:56:19 +0000 (18:56 -0500)]
Hexagon: Add basic stacktrace functionality for Hexagon architecture.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add configuration and makefiles for the Hexagon architecture.
Richard Kuo [Mon, 31 Oct 2011 23:55:58 +0000 (18:55 -0500)]
Hexagon: Add configuration and makefiles for the Hexagon architecture.

Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Comet platform support
Richard Kuo [Mon, 31 Oct 2011 23:55:25 +0000 (18:55 -0500)]
Hexagon: Comet platform support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: kgdb support files
Linas Vepstas [Mon, 31 Oct 2011 23:54:43 +0000 (18:54 -0500)]
Hexagon: kgdb support files

Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add page-fault support.
Richard Kuo [Mon, 31 Oct 2011 23:54:08 +0000 (18:54 -0500)]
Hexagon: Add page-fault support.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add page table header files & etc.
Richard Kuo [Mon, 31 Oct 2011 23:53:38 +0000 (18:53 -0500)]
Hexagon: Add page table header files & etc.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add ioremap support
Richard Kuo [Mon, 31 Oct 2011 23:52:53 +0000 (18:52 -0500)]
Hexagon: Add ioremap support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Provide DMA implementation
Richard Kuo [Mon, 31 Oct 2011 23:52:22 +0000 (18:52 -0500)]
Hexagon: Provide DMA implementation

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Implement basic TLB management routines for Hexagon.
Richard Kuo [Mon, 31 Oct 2011 23:52:00 +0000 (18:52 -0500)]
Hexagon: Implement basic TLB management routines for Hexagon.

Mostly all stubs, as the TLB is managed by the hypervisor.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Implement basic cache-flush support
Richard Kuo [Mon, 31 Oct 2011 23:50:51 +0000 (18:50 -0500)]
Hexagon: Implement basic cache-flush support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Provide basic implementation and/or stubs for I/O routines.
Richard Kuo [Mon, 31 Oct 2011 23:48:50 +0000 (18:48 -0500)]
Hexagon: Provide basic implementation and/or stubs for I/O routines.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add user access functions
Richard Kuo [Mon, 31 Oct 2011 23:48:07 +0000 (18:48 -0500)]
Hexagon: Add user access functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add locking types and functions
Richard Kuo [Mon, 31 Oct 2011 23:47:33 +0000 (18:47 -0500)]
Hexagon: Add locking types and functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add SMP support
Richard Kuo [Mon, 31 Oct 2011 23:46:34 +0000 (18:46 -0500)]
Hexagon: Add SMP support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Provide basic debugging and system trap support.
Richard Kuo [Mon, 31 Oct 2011 23:44:34 +0000 (18:44 -0500)]
Hexagon: Provide basic debugging and system trap support.

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add ptrace support
Richard Kuo [Mon, 31 Oct 2011 23:43:44 +0000 (18:43 -0500)]
Hexagon: Add ptrace support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add time and timer functions
Richard Kuo [Mon, 31 Oct 2011 23:43:24 +0000 (18:43 -0500)]
Hexagon: Add time and timer functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add interrupts
Richard Kuo [Mon, 31 Oct 2011 23:42:51 +0000 (18:42 -0500)]
Hexagon: Add interrupts

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add startup code
Richard Kuo [Mon, 31 Oct 2011 23:42:28 +0000 (18:42 -0500)]
Hexagon: Add startup code

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add init_task and process functions
Richard Kuo [Mon, 31 Oct 2011 23:41:49 +0000 (18:41 -0500)]
Hexagon: Add init_task and process functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add signal functions
Richard Kuo [Mon, 31 Oct 2011 23:41:21 +0000 (18:41 -0500)]
Hexagon: Add signal functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Support dynamic module loading.
Linas Vepstas [Mon, 31 Oct 2011 23:40:46 +0000 (18:40 -0500)]
Hexagon: Support dynamic module loading.

Modules should be compiled as ordinary .o's; shared objects are not
supported.

Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Export ksyms defined in assembly files.
Linas Vepstas [Mon, 31 Oct 2011 23:40:19 +0000 (18:40 -0500)]
Hexagon: Export ksyms defined in assembly files.

Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add hypervisor interface
Richard Kuo [Mon, 31 Oct 2011 23:39:14 +0000 (18:39 -0500)]
Hexagon: Add hypervisor interface

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add memcpy and memset accelerated functions
Richard Kuo [Mon, 31 Oct 2011 23:38:38 +0000 (18:38 -0500)]
Hexagon: Add memcpy and memset accelerated functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add checksum functions
Richard Kuo [Mon, 31 Oct 2011 23:38:04 +0000 (18:38 -0500)]
Hexagon: Add checksum functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add delay functions
Richard Kuo [Mon, 31 Oct 2011 23:37:20 +0000 (18:37 -0500)]
Hexagon: Add delay functions

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add threadinfo
Richard Kuo [Mon, 31 Oct 2011 23:36:46 +0000 (18:36 -0500)]
Hexagon: Add threadinfo

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add processor and system headers
Richard Kuo [Mon, 31 Oct 2011 23:36:04 +0000 (18:36 -0500)]
Hexagon: Add processor and system headers

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add syscalls
Richard Kuo [Mon, 31 Oct 2011 23:35:16 +0000 (18:35 -0500)]
Hexagon: Add syscalls

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add atomic ops support
Richard Kuo [Mon, 31 Oct 2011 23:28:13 +0000 (18:28 -0500)]
Hexagon: Add atomic ops support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add bitops support
Richard Kuo [Mon, 31 Oct 2011 23:27:45 +0000 (18:27 -0500)]
Hexagon: Add bitops support

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Core arch-specific header files
Richard Kuo [Mon, 31 Oct 2011 23:27:03 +0000 (18:27 -0500)]
Hexagon: Core arch-specific header files

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoHexagon: Add generic headers
Richard Kuo [Mon, 31 Oct 2011 23:26:34 +0000 (18:26 -0500)]
Hexagon: Add generic headers

Signed-off-by: Richard Kuo <rkuo@codeaurora.org>
Signed-off-by: Linas Vepstas <linas@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agocrypto: user - Depend on NET instead of selecting it
Herbert Xu [Tue, 1 Nov 2011 01:12:43 +0000 (12:12 +1100)]
crypto: user - Depend on NET instead of selecting it

Selecting NET causes all sorts of issues, including a dependency
loop involving bluetooth.  This patch makes it a dependency instead.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
10 years agoMerge branch 'akpm' (Andrew's incoming)
Linus Torvalds [Tue, 1 Nov 2011 00:46:07 +0000 (17:46 -0700)]
Merge branch 'akpm' (Andrew's incoming)

Quoth Andrew:

 - Most of MM.  Still waiting for the poweroc guys to get off their
   butts and review some threaded hugepages patches.

 - alpha

 - vfs bits

 - drivers/misc

 - a few core kerenl tweaks

 - printk() features

 - MAINTAINERS updates

 - backlight merge

 - leds merge

 - various lib/ updates

 - checkpatch updates

* akpm: (127 commits)
  epoll: fix spurious lockdep warnings
  checkpatch: add a --strict check for utf-8 in commit logs
  kernel.h/checkpatch: mark strict_strto<foo> and simple_strto<foo> as obsolete
  llist-return-whether-list-is-empty-before-adding-in-llist_add-fix
  wireless: at76c50x: follow rename pack_hex_byte to hex_byte_pack
  fat: follow rename pack_hex_byte() to hex_byte_pack()
  security: follow rename pack_hex_byte() to hex_byte_pack()
  kgdb: follow rename pack_hex_byte() to hex_byte_pack()
  lib: rename pack_hex_byte() to hex_byte_pack()
  lib/string.c: fix strim() semantics for strings that have only blanks
  lib/idr.c: fix comment for ida_get_new_above()
  lib/percpu_counter.c: enclose hotplug only variables in hotplug ifdef
  lib/bitmap.c: quiet sparse noise about address space
  lib/spinlock_debug.c: print owner on spinlock lockup
  lib/kstrtox: common code between kstrto*() and simple_strto*() functions
  drivers/leds/leds-lp5521.c: check if reset is successful
  leds: turn the blink_timer off before starting to blink
  leds: save the delay values after a successful call to blink_set()
  drivers/leds/leds-gpio.c: use gpio_get_value_cansleep() when initializing
  drivers/leds/leds-lm3530.c: add __devexit_p where needed
  ...

10 years agoepoll: fix spurious lockdep warnings
Nelson Elhage [Tue, 1 Nov 2011 00:13:14 +0000 (17:13 -0700)]
epoll: fix spurious lockdep warnings

epoll can acquire recursively acquire ep->mtx on multiple "struct
eventpoll"s at once in the case where one epoll fd is monitoring another
epoll fd.  This is perfectly OK, since we're careful about the lock
ordering, but it causes spurious lockdep warnings.  Annotate the recursion
using mutex_lock_nested, and add a comment explaining the nesting rules
for good measure.

Recent versions of systemd are triggering this, and it can also be
demonstrated with the following trivial test program:

--------------------8<--------------------

int main(void) {
   int e1, e2;
   struct epoll_event evt = {
       .events = EPOLLIN
   };

   e1 = epoll_create1(0);
   e2 = epoll_create1(0);
   epoll_ctl(e1, EPOLL_CTL_ADD, e2, &evt);
   return 0;
}
--------------------8<--------------------

Reported-by: Paul Bolle <pebolle@tiscali.nl>
Tested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nelson Elhage <nelhage@nelhage.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agocheckpatch: add a --strict check for utf-8 in commit logs
Joe Perches [Tue, 1 Nov 2011 00:13:12 +0000 (17:13 -0700)]
checkpatch: add a --strict check for utf-8 in commit logs

Some find using utf-8 in commit logs inappropriate.

Some patch commit logs contain unintended utf-8 characters when doing
things like copy/pasting compilation output.

Look for the start of any commit log by skipping initial lines that look
like email headers and "From: " lines.

Stop looking for utf-8 at the first signature line.

Signed-off-by: Joe Perches <joe@perches.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agokernel.h/checkpatch: mark strict_strto<foo> and simple_strto<foo> as obsolete
Joe Perches [Tue, 1 Nov 2011 00:13:10 +0000 (17:13 -0700)]
kernel.h/checkpatch: mark strict_strto<foo> and simple_strto<foo> as obsolete

Mark obsolete/deprecated strict_strto<foo> and simple_strto<foo> functions
and macros as obsolete.

Update checkpatch to warn about their use.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agollist-return-whether-list-is-empty-before-adding-in-llist_add-fix
Andrew Morton [Tue, 1 Nov 2011 00:13:08 +0000 (17:13 -0700)]
llist-return-whether-list-is-empty-before-adding-in-llist_add-fix

clarify comment

Cc: Huang Ying <ying.huang@intel.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agowireless: at76c50x: follow rename pack_hex_byte to hex_byte_pack
Andy Shevchenko [Tue, 1 Nov 2011 00:13:00 +0000 (17:13 -0700)]
wireless: at76c50x: follow rename pack_hex_byte to hex_byte_pack

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agofat: follow rename pack_hex_byte() to hex_byte_pack()
Andy Shevchenko [Tue, 1 Nov 2011 00:12:57 +0000 (17:12 -0700)]
fat: follow rename pack_hex_byte() to hex_byte_pack()

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agosecurity: follow rename pack_hex_byte() to hex_byte_pack()
Andy Shevchenko [Tue, 1 Nov 2011 00:12:55 +0000 (17:12 -0700)]
security: follow rename pack_hex_byte() to hex_byte_pack()

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agokgdb: follow rename pack_hex_byte() to hex_byte_pack()
Andy Shevchenko [Tue, 1 Nov 2011 00:12:51 +0000 (17:12 -0700)]
kgdb: follow rename pack_hex_byte() to hex_byte_pack()

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib: rename pack_hex_byte() to hex_byte_pack()
Andy Shevchenko [Tue, 1 Nov 2011 00:12:41 +0000 (17:12 -0700)]
lib: rename pack_hex_byte() to hex_byte_pack()

As suggested by Andrew Morton in [1] there is better to have most
significant part first in the function name.

[1] https://lkml.org/lkml/2011/9/20/22

There is no functional change.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Mimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib/string.c: fix strim() semantics for strings that have only blanks
Michael Holzheu [Tue, 1 Nov 2011 00:12:37 +0000 (17:12 -0700)]
lib/string.c: fix strim() semantics for strings that have only blanks

Commit 84c95c9acf0 ("string: on strstrip(), first remove leading spaces
before running over str") improved\7f the performance of the strim()
function.

Unfortunately this changed the semantics of strim() and broke my code.
Before the patch it was possible to use strim() without using the return
value for removing trailing spaces from strings that had either only
blanks or only trailing blanks.

Now this does not work any longer for strings that *only* have blanks.

Before patch: "   " -> ""    (empty string)
After patch:  "   " -> "   " (no change)

I think we should remove your patch to restore the old behavior.

The description (lib/string.c):

 * Note that the first trailing whitespace is replaced with a %NUL-terminator

=> The first trailing whitespace of a string that only has whitespace
   characters is the first whitespace

The patch restores the old strim() semantics.

Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Andre Goddard Rosa <andre.goddard@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib/idr.c: fix comment for ida_get_new_above()
Wang Sheng-Hui [Tue, 1 Nov 2011 00:12:36 +0000 (17:12 -0700)]
lib/idr.c: fix comment for ida_get_new_above()

Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib/percpu_counter.c: enclose hotplug only variables in hotplug ifdef
Glauber Costa [Tue, 1 Nov 2011 00:12:34 +0000 (17:12 -0700)]
lib/percpu_counter.c: enclose hotplug only variables in hotplug ifdef

These variables are only used when CONFIG_HOTPLUG_CPU is enabled, they are
ifdef'ed everywhere else.  So don't define them when CONFIG_HOTPLUG_CPU is
not enabled.

Signed-off-by: Glauber Costa <glommer@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib/bitmap.c: quiet sparse noise about address space
H Hartley Sweeten [Tue, 1 Nov 2011 00:12:32 +0000 (17:12 -0700)]
lib/bitmap.c: quiet sparse noise about address space

__bitmap_parse() and __bitmap_parselist() both take a pointer to a kernel
buffer as a parameter and then cast it to a pointer to user buffer for use
in cases when the parameter is_user indicates that the buffer is actually
located in user space.  This casting, and the casts in the callers,
results in sparse noise like the following:

warning: incorrect type in initializer (different address spaces)
  expected char const [noderef] <asn:1>*ubuf
  got char const *buf
warning: cast removes address space of expression

Since these casts are intentional, use __force to quiet the noise.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib/spinlock_debug.c: print owner on spinlock lockup
Akinobu Mita [Tue, 1 Nov 2011 00:12:29 +0000 (17:12 -0700)]
lib/spinlock_debug.c: print owner on spinlock lockup

When SPIN_BUG_ON is triggered, the lock owner information is reported.
But it is omitted when spinlock lockup is detected.

This information is useful especially on the architectures which don't
implement trigger_all_cpu_backtrace() that is called just after detecting
lockup.  So report it and also avoid message format duplication.

Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolib/kstrtox: common code between kstrto*() and simple_strto*() functions
Alexey Dobriyan [Tue, 1 Nov 2011 00:12:28 +0000 (17:12 -0700)]
lib/kstrtox: common code between kstrto*() and simple_strto*() functions

Currently termination logic (\0 or \n\0) is hardcoded in _kstrtoull(),
avoid that for code reuse between kstrto*() and simple_strtoull().
Essentially, make them different only in termination logic.

simple_strtoull() (and scanf(), BTW) ignores integer overflow, that's a
bug we currently don't have guts to fix, making KSTRTOX_OVERFLOW hack
necessary.

Almost forgot: patch shrinks code size by about ~80 bytes on x86_64.

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-lp5521.c: check if reset is successful
Srinidhi KASAGAR [Tue, 1 Nov 2011 00:12:24 +0000 (17:12 -0700)]
drivers/leds/leds-lp5521.c: check if reset is successful

Make sure that the reset is successful by issuing a dummy read to R
channel current register and check its default value.  On some platforms,
without this dummy read, any further access to {R/G/B}_EXEC will not have
any impact.

[akpm@linux-foundation.org: fix up code comment]
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Tested-by: Naga Radhesh <naga.radheshy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoleds: turn the blink_timer off before starting to blink
Antonio Ospite [Tue, 1 Nov 2011 00:12:22 +0000 (17:12 -0700)]
leds: turn the blink_timer off before starting to blink

Depending on the implementation of the hardware blinking function in
blink_set(), the led can support hardware blinking for some values of
delay_on and delay_off and fall-back to software blinking for some other
values.

Turning off the blink_timer unconditionally before starting to blink
make sure that a sequence like:

  OFF
  hardware blinking
  software blinking
  hardware blinking

does not leave the software blinking timer active.

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoleds: save the delay values after a successful call to blink_set()
Antonio Ospite [Tue, 1 Nov 2011 00:12:19 +0000 (17:12 -0700)]
leds: save the delay values after a successful call to blink_set()

When calling the hardware blinking function implemented by blink_set(),
the delay_on and delay_off values are not preserved across calls.

Fix that and make the "timer" trigger work as expected when hardware
blinking is available.

BEFORE the fix:
  $ cd /sys/class/leds/someled
  $ echo timer > trigger
  $ cat delay_on delay_off
  0
  0
  $ echo 100 > delay_on
  $ cat delay_on delay_off
  0
  0
  $ echo 100 > delay_off
  $ cat delay_on delay_off
  0
  0

AFTER the fix:
  $ cd /sys/class/leds/someled
  $ echo timer > trigger
  $ cat delay_on delay_off
  0
  0
  $ echo 100 > delay_on
  $ cat delay_on delay_off
  100
  0
  $ echo 100 > delay_off
  $ cat delay_on delay_off
  100
  100

Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-gpio.c: use gpio_get_value_cansleep() when initializing
David Daney [Tue, 1 Nov 2011 00:12:17 +0000 (17:12 -0700)]
drivers/leds/leds-gpio.c: use gpio_get_value_cansleep() when initializing

I get the following warning:

------------[ cut here ]------------
WARNING: at drivers/gpio/gpiolib.c:1559 __gpio_get_value+0x90/0x98()
Modules linked in:
Call Trace:
[<ffffffff81440950>] dump_stack+0x8/0x34
[<ffffffff81141478>] warn_slowpath_common+0x78/0xa0
[<ffffffff812f0958>] __gpio_get_value+0x90/0x98
[<ffffffff81434f04>] create_gpio_led+0xdc/0x194
[<ffffffff8143524c>] gpio_led_probe+0x290/0x36c
[<ffffffff8130e8b0>] driver_probe_device+0x78/0x1b0
[<ffffffff8130eaa8>] __driver_attach+0xc0/0xc8
[<ffffffff8130d7ac>] bus_for_each_dev+0x64/0xb0
[<ffffffff8130e130>] bus_add_driver+0x1c8/0x2a8
[<ffffffff8130f100>] driver_register+0x90/0x180
[<ffffffff81100438>] do_one_initcall+0x38/0x160

---[ end trace ee38723fbefcd65c ]---

My GPIOs are on an I2C port expander, so we must use the *_cansleep()
variant of the GPIO functions.  This is was not being done in
create_gpio_led().

We can change gpio_get_value() to gpio_get_value_cansleep() because it is
only called from the platform_driver probe function, which is a context
where we can sleep.

Only tested on my gpio_cansleep() system, but it seems safe for all
systems.

Signed-off-by: David Daney <david.daney@cavium.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Trent Piepho <tpiepho@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-lm3530.c: add __devexit_p where needed
Axel Lin [Tue, 1 Nov 2011 00:12:15 +0000 (17:12 -0700)]
drivers/leds/leds-lm3530.c: add __devexit_p where needed

According to the comments in include/linux/init.h:

"Pointers to __devexit functions must use __devexit_p(function_name), the
wrapper will insert either the function_name or NULL, depending on the config
options."

We have __devexit annotation for lm3530_remove(), so add __devexit_p to
the `struct i2c_driver'.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar SAHU <shreshthakumar.sahu@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-lp5521.c: avoid writing uninitialized value to LP5521_REG_OP_MODE...
Axel Lin [Tue, 1 Nov 2011 00:12:12 +0000 (17:12 -0700)]
drivers/leds/leds-lp5521.c: avoid writing uninitialized value to LP5521_REG_OP_MODE register

If lp5521_read fails, engine_state variable is not initialized.
If lp5521_read fails, we should return error.
This patch fixes below warning.

  CC      drivers/leds/leds-lp5521.o
drivers/leds/leds-lp5521.c: In function 'lp5521_set_engine_mode':
drivers/leds/leds-lp5521.c:168: warning: 'engine_state' may be used uninitialized in this function

[akpm@linux-foundation.org: remove unneeded "ret |="]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-renesas-tpu.c: move Renesas TPU LED driver platform data
Magnus Damm [Tue, 1 Nov 2011 00:12:09 +0000 (17:12 -0700)]
drivers/leds/leds-renesas-tpu.c: move Renesas TPU LED driver platform data

Use the platform_data include directory for the TPU LED driver, as
suggested by Paul Mundt.

Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-renesas-tpu.c: update driver to use workqueue
Magnus Damm [Tue, 1 Nov 2011 00:12:06 +0000 (17:12 -0700)]
drivers/leds/leds-renesas-tpu.c: update driver to use workqueue

Use a workqueue in the Renesas TPU LED driver to allow the Runtime PM code
to sleep.

Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/leds-lm3530.c: remove obsolete cleanup for clientdata
Wolfram Sang [Tue, 1 Nov 2011 00:12:03 +0000 (17:12 -0700)]
drivers/leds/leds-lm3530.c: remove obsolete cleanup for clientdata

A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error.  This is obsolete meanwhile, the core
will do it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/leds/led-triggers.c: fix memory leak
Masakazu Mokuno [Tue, 1 Nov 2011 00:11:59 +0000 (17:11 -0700)]
drivers/leds/led-triggers.c: fix memory leak

The memory for struct led_trigger should be kfreed in the
led_trigger_register() error path.  Also this function should return NULL
on error.

Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoleds: Renesas TPU LED driver
Magnus Damm [Tue, 1 Nov 2011 00:11:55 +0000 (17:11 -0700)]
leds: Renesas TPU LED driver

Add V2 of the LED driver for a single timer channel for the TPU hardware
block commonly found in Renesas SoCs.

The driver has been written with optimal Power Management in mind, so to
save power the LED is driven as a regular GPIO pin in case of maximum
brightness and power off which allows the TPU hardware to be idle and
which in turn allows the clocks to be stopped and the power domain to be
turned off transparently.

Any other brightness level requires use of the TPU hardware in PWM mode.
TPU hardware device clocks and power are managed through Runtime PM.
System suspend and resume is known to be working - during suspend the LED
is set to off by the generic LED code.

The TPU hardware timer is equipeed with a 16-bit counter together with an
up-to-divide-by-64 prescaler which makes the hardware suitable for
brightness control.  Hardware blink is unsupported.

The LED PWM waveform has been verified with a Fluke 123 Scope meter on a
sh7372 Mackerel board.  Tested with experimental sh7372 A3SP power domain
patches.  Platform device bind/unbind tested ok.

V2 has been tested on the DS2 LED of the sh73a0-based AG5EVM.

[axel.lin@gmail.com: include linux/module.h]
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agobacklight: rename corgibl_limit_intensity() to genericbl_limit_intensity()
Axel Lin [Tue, 1 Nov 2011 00:11:52 +0000 (17:11 -0700)]
backlight: rename corgibl_limit_intensity() to genericbl_limit_intensity()

The rename of corgibl_limit_intensity is missed in commit d00ba726
("backlight: Rename the corgi backlight driver to generic").  Let's fix it
now.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/video/backlight/l4f00242t03.c: use gpio_request_one() to simplify error handling
Fabio Estevam [Tue, 1 Nov 2011 00:11:50 +0000 (17:11 -0700)]
drivers/video/backlight/l4f00242t03.c: use gpio_request_one() to simplify error handling

Using gpio_request_one can make the error handling simpler.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agobacklight: fix broken regulator API usage in l4f00242t03
Mark Brown [Tue, 1 Nov 2011 00:11:48 +0000 (17:11 -0700)]
backlight: fix broken regulator API usage in l4f00242t03

The regulator support in the l4f00242t03 is very non-idiomatic.  Rather
than requesting the regulators based on the device name and the supply
names used by the device the driver requires boards to pass system
specific supply names around through platform data.  The driver also
conditionally requests the regulators based on this platform data, adding
unneeded conditional code to the driver.

Fix this by removing the platform data and converting to the standard
idiom, also updating all in tree users of the driver.  As no datasheet
appears to be available for the LCD I'm guessing the names for the
supplies based on the existing users and I've no ability to do anything
more than compile test.

The use of regulator_set_voltage() in the driver is also problematic,
since fixed voltages are required the expectation would be that the
voltages would be fixed in the constraints set by the machines rather than
manually configured by the driver, but is less problematic.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agovideo/backlight: remove obsolete cleanup for clientdata
Wolfram Sang [Tue, 1 Nov 2011 00:11:44 +0000 (17:11 -0700)]
video/backlight: remove obsolete cleanup for clientdata

A few new i2c-drivers came into the kernel which clear the
clientdata-pointer on exit or error.  This is obsolete meanwhile, the core
will do it.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoMAINTAINERS: add ASLR maintainer
Jiri Kosina [Tue, 1 Nov 2011 00:11:41 +0000 (17:11 -0700)]
MAINTAINERS: add ASLR maintainer

Since achieving the full ASLR by merging the PIE randomization in commit
cc503c1b43 ("x86: PIE executable randomization"), I have been dealing with
most (if not all) of the bugreports reported against userspace address
space randomization, so it might be a good idea to provide a decent
contact point in MAINTAINERS.

Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoMAINTAINERS: Linas has moved
Linas Vepstas [Tue, 1 Nov 2011 00:11:38 +0000 (17:11 -0700)]
MAINTAINERS: Linas has moved

While ego surfing, I noticed an email address problem.

Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoMAINTAINERS: add new entry for ideapad-laptop
Ike Panhc [Tue, 1 Nov 2011 00:11:37 +0000 (17:11 -0700)]
MAINTAINERS: add new entry for ideapad-laptop

Signed-off-by: Ike Panhc <ike.pan@canonical.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agotreewide: use __printf not __attribute__((format(printf,...)))
Joe Perches [Tue, 1 Nov 2011 00:11:33 +0000 (17:11 -0700)]
treewide: use __printf not __attribute__((format(printf,...)))

Standardize the style for compiler based printf format verification.
Standardized the location of __printf too.

Done via script and a little typing.

$ grep -rPl --include=*.[ch] -w "__attribute__" * | \
  grep -vP "^(tools|scripts|include/linux/compiler-gcc.h)" | \
  xargs perl -n -i -e 'local $/; while (<>) { s/\b__attribute__\s*\(\s*\(\s*format\s*\(\s*printf\s*,\s*(.+)\s*,\s*(.+)\s*\)\s*\)\s*\)/__printf($1, $2)/g ; print; }'

[akpm@linux-foundation.org: revert arch bits]
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoprintk: remove bounds checking for log_prefix
William Douglas [Tue, 1 Nov 2011 00:11:31 +0000 (17:11 -0700)]
printk: remove bounds checking for log_prefix

Currently log_prefix is testing that the first character of the log level
and facility is less than '0' and greater than '9' (which is always
false).

Since the code being updated works because strtoul bombs out (endp isn't
updated) and 0 is returned anyway just remove the check and don't change
the behavior of the function.

Signed-off-by: William Douglas <william.douglas@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoprintk: fix bounds checking for log_prefix
William Douglas [Tue, 1 Nov 2011 00:11:29 +0000 (17:11 -0700)]
printk: fix bounds checking for log_prefix

Currently log_prefix is testing that the first character of the log level
and facility is less than '0' and greater than '9' (which is always
false).  It should be testing to see if the character less than '0' or
greater than '9' instead.  This patch makes that change.

The code being changed worked because strtoul bombs out (endp isn't
updated) and 0 is returned anyway.

Signed-off-by: William Douglas <william.douglas@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoprintk: add console_suspend module parameter
Yanmin Zhang [Tue, 1 Nov 2011 00:11:27 +0000 (17:11 -0700)]
printk: add console_suspend module parameter

We are enabling some power features on medfield.  To test suspend-2-RAM
conveniently, we need turn on/off console_suspend_enabled frequently.

Add a module parameter, so users could change it by:
/sys/module/printk/parameters/console_suspend

Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agoprintk: add module parameter ignore_loglevel to control ignore_loglevel
Yanmin Zhang [Tue, 1 Nov 2011 00:11:25 +0000 (17:11 -0700)]
printk: add module parameter ignore_loglevel to control ignore_loglevel

We are enabling some power features on medfield.  To test suspend-2-RAM
conveniently, we need turn on/off ignore_loglevel frequently without
rebooting.

Add a module parameter, so users can change it by:
/sys/module/printk/parameters/ignore_loglevel

Signed-off-by: Yanmin Zhang <yanmin.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agokernel/sysctl.c: add cap_last_cap to /proc/sys/kernel
Dan Ballard [Tue, 1 Nov 2011 00:11:20 +0000 (17:11 -0700)]
kernel/sysctl.c: add cap_last_cap to /proc/sys/kernel

Userspace needs to know the highest valid capability of the running
kernel, which right now cannot reliably be retrieved from the header files
only.  The fact that this value cannot be determined properly right now
creates various problems for libraries compiled on newer header files
which are run on older kernels.  They assume capabilities are available
which actually aren't.  libcap-ng is one example.  And we ran into the
same problem with systemd too.

Now the capability is exported in /proc/sys/kernel/cap_last_cap.

[akpm@linux-foundation.org: make cap_last_cap const, per Ulrich]
Signed-off-by: Dan Ballard <dan@mindstab.net>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Ulrich Drepper <drepper@akkadia.org>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agowatchdog: move watchdog_*_all_cpus under CONFIG_SYSCTL
Vasily Averin [Tue, 1 Nov 2011 00:11:18 +0000 (17:11 -0700)]
watchdog: move watchdog_*_all_cpus under CONFIG_SYSCTL

Fix compilation warnings for CONFIG_SYSCTL=n:

fixed compilation warnings in case of disabled CONFIG_SYSCTL
kernel/watchdog.c:483:13: warning: `watchdog_enable_all_cpus' defined but not used
kernel/watchdog.c:500:13: warning: `watchdog_disable_all_cpus' defined but not used

these functions are static and are used only in sysctl handler, so move
them inside #ifdef CONFIG_SYSCTL too

Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agostop_machine: make stop_machine safe and efficient to call early
Jeremy Fitzhardinge [Tue, 1 Nov 2011 00:11:15 +0000 (17:11 -0700)]
stop_machine: make stop_machine safe and efficient to call early

Make stop_machine() safe to call early in boot, before SMP has been set
up, by simply calling the callback function directly if there's only one
CPU online.

[ Fixes from AKPM:
   - add comment
   - local_irq_flags, not save_flags
   - also call hard_irq_disable() for systems which need it

  Tejun suggested using an explicit flag rather than just looking at
  the online cpu count. ]

Cc: Tejun Heo <tj@kernel.org>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Tejun Heo <htejun@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/misc/ad525x_dpot-i2c.c: add i2c support for AD5161
Peter Korsgaard [Tue, 1 Nov 2011 00:11:12 +0000 (17:11 -0700)]
drivers/misc/ad525x_dpot-i2c.c: add i2c support for AD5161

Commit 6c536e4ce8e ("ad525x_dpot: add support for SPI parts") added
support for the AD5161 through SPI, but the device supports both I2C and
SPI (depending on the DIS pin), so add it to -i2c as well.

Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodriver/misc/fsa9480.c fix potential null-pointer dereference
Jonghwan Choi [Tue, 1 Nov 2011 00:11:09 +0000 (17:11 -0700)]
driver/misc/fsa9480.c fix potential null-pointer dereference

Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Cc: Donggeun Kim <dg77.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3lv02d: make regulator API usage unconditional
Mark Brown [Tue, 1 Nov 2011 00:11:07 +0000 (17:11 -0700)]
lis3lv02d: make regulator API usage unconditional

The regulator API contains a range of features for stubbing itself out
when not in use and for transparently restricting the actual effect of
regulator API calls where they can't be supported on a particular system
so that drivers don't need to individually implement this.  Simplify the
driver slightly by making use of this idiom.

The only in tree user is ecovec24 which does not use the regulator API.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: remove the references to the global variable in core driver
Éric Piel [Tue, 1 Nov 2011 00:11:05 +0000 (17:11 -0700)]
lis3: remove the references to the global variable in core driver

[ilkka.koskinen@nokia.com: fix arg to lis3->read()]
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Subject: lis3-remove-the-references-to-the-global-variable-in-core-driver-fix
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: change exported function to use passed parameter
Éric Piel [Tue, 1 Nov 2011 00:11:02 +0000 (17:11 -0700)]
lis3: change exported function to use passed parameter

Change exported functions to use the device given as parameter
instead of the global one.

Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: use consistent naming of variables
Éric Piel [Tue, 1 Nov 2011 00:10:58 +0000 (17:10 -0700)]
lis3: use consistent naming of variables

Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: free regulators if probe() fails
Éric Piel [Tue, 1 Nov 2011 00:10:54 +0000 (17:10 -0700)]
lis3: free regulators if probe() fails

Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agohp_accel: add HP ProBook 655x
Éric Piel [Tue, 1 Nov 2011 00:10:50 +0000 (17:10 -0700)]
hp_accel: add HP ProBook 655x

Add axis correction for HP ProBook 6555b.

Signed-off-by: Malte Starostik <m-starostik@versanet.de>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: add support for HP EliteBook 8540w
Éric Piel [Tue, 1 Nov 2011 00:10:46 +0000 (17:10 -0700)]
lis3: add support for HP EliteBook 8540w

Add axis correction for HP EliteBook 8540w.

Reported-by: Lyall Pearce <lyall.pearce@hp.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: add support for HP EliteBook 2730p
Éric Piel [Tue, 1 Nov 2011 00:10:43 +0000 (17:10 -0700)]
lis3: add support for HP EliteBook 2730p

Add axis correction for HP EliteBook 2730p.

Tested-by: Witold Pilat <witold.pilat@gmail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3: update maintainer information
Éric Piel [Tue, 1 Nov 2011 00:10:41 +0000 (17:10 -0700)]
lis3: update maintainer information

In the move of the lis3 driver, the hp_accel.c file got dropped from the
MAINTAINER file. Make it explicit again that this file is tied to lis3
again.

Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agolis3lv02d: avoid divide by zero due to unchecked
Éric Piel [Tue, 1 Nov 2011 00:10:31 +0000 (17:10 -0700)]
lis3lv02d: avoid divide by zero due to unchecked

After an "unexpected" reboot, I found this Oops in my logs:

divide error: 0000 [#1] PREEMPT SMP=20
CPU 0=20
Modules linked in: lis3lv02d hp_wmi input_polldev [...]
Pid: 390, comm: modprobe Tainted: G         C  2.6.39-rc7-wl+=20
RIP: 0010:[<ffffffffa014b427>]  [<ffffffffa014b427>]
 lis3lv02d_poweron+0x4e/0x94 [lis3lv02d]
RSP: 0018:ffff8801d6407cf8  EFLAGS: 00010246
RAX: 0000000000000bb8 RBX: ffffffffa014e000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffea00066e4708 RDI: ffff8801df002700
RBP: ffff8801d6407d18 R08: ffffea00066c5a30 R09: ffffffff812498c9
R10: ffff8801d7bfcea0 R11: ffff8801d7bfce10 R12: 0000000000000bb8
R13: 00000000ffffffda R14: ffffffffa0154120 R15: ffffffffa0154030
=46S:  00007fc0705db700(0000) GS:ffff8801dfa00000(0000) knlGS:0
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007f33549174f0 CR3: 00000001d65c9000 CR4: 00000000000406f0
Process modprobe (pid: 390, threadinfo ffff8801d6406000, task ffff8801d6b40=
000)
Stack:
 ffffffffa0154120 62ffffffa0154030 ffffffffa014e000 00000000ffffffea
 ffff8801d6407d58 ffffffffa014bcc1 0000000000000000 0000000000000048
 ffff8801d8bae800 00000000ffffffea 00000000ffffffda ffffffffa0154120
Call Trace:
 [<ffffffffa014bcc1>] lis3lv02d_init_device+0x1ce/0x496 [lis3lv02d]
 [<ffffffffa01522ff>] lis3lv02d_add+0x10f/0x17c [hp_accel]
 [<ffffffff81233e11>] acpi_device_probe+0x49/0x117
[...]
Code: 3a 75 06 80 4d ef 50 eb 04 80 4d ef 40 0f b6 55 ef be 21
00 00 00 48 89 df ff 53 18 44 8b 63 6c e8 3e fc ff ff 89 c1 44
89 e0 99 <f7> f9 89 c7 e8 93 82 ef e0 48 83 7b 30 00 74 2d 45
31 e4 80 7b=20
RIP  [<ffffffffa014b427>] lis3lv02d_poweron+0x4e/0x94 [lis3lv02d]
 RSP <ffff8801d6407cf8>

>From my POV, it looks like the hardware is not working as expected
and returns a bogus data rate. The driver doesn't check the result
and directly uses it as some sort of divisor in some places:

msleep(lis3->pwron_delay / lis3lv02d_get_odr());

Under this circumstances, this could very well cause the
"divide by zero" exception from above.

For now, I fixed it the easiest and most obvious way:
Check if the result is sane and if it isn't use a sane default
instead. I went for "100" in the latter case, simply because
/sys/devices/platform/lis3lv02d/rate returns it on a successful
boot.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Éric Piel <eric.piel@tremplin-utc.net>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Witold Pilat <witold.pilat@gmail.com>
Cc: Lyall Pearce <lyall.pearce@hp.com>
Cc: Malte Starostik <m-starostik@versanet.de>
Cc: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agodrivers/hwmon/hwmon.c: convert idr to ida and use ida_simple_get()
Jonathan Cameron [Tue, 1 Nov 2011 00:10:27 +0000 (17:10 -0700)]
drivers/hwmon/hwmon.c: convert idr to ida and use ida_simple_get()

A straightforward looking use of idr for a device id.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
10 years agohwmon: convert idr to ida and use ida_simple interface
Jonathan Cameron [Tue, 1 Nov 2011 00:10:09 +0000 (17:10 -0700)]
hwmon: convert idr to ida and use ida_simple interface

hwmon was using an idr with a NULL pointer, so convert to an
ida which then allows use of Rusty's ida_simple_get.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>