--- /dev/null
+What: /sys/class/regulator/.../state
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ state. This holds the regulator output state.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'unknown'
+
+ 'enabled' means the regulator output is ON and is supplying
+ power to the system.
+
+ 'disabled' means the regulator output is OFF and is not
+ supplying power to the system..
+
+ 'unknown' means software cannot determine the state.
+
+ NOTE: this field can be used in conjunction with microvolts
+ and microamps to determine regulator output levels.
+
+
+What: /sys/class/regulator/.../type
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ type. This holds the regulator type.
+
+ This will be one of the following strings:
+
+ 'voltage'
+ 'current'
+ 'unknown'
+
+ 'voltage' means the regulator output voltage can be controlled
+ by software.
+
+ 'current' means the regulator output current limit can be
+ controlled by software.
+
+ 'unknown' means software cannot control either voltage or
+ current limit.
+
+
+What: /sys/class/regulator/.../microvolts
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ microvolts. This holds the regulator output voltage setting
+ measured in microvolts (i.e. E-6 Volts).
+
+ NOTE: This value should not be used to determine the regulator
+ output voltage level as this value is the same regardless of
+ whether the regulator is enabled or disabled.
+
+
+What: /sys/class/regulator/.../microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ microamps. This holds the regulator output current limit
+ setting measured in microamps (i.e. E-6 Amps).
+
+ NOTE: This value should not be used to determine the regulator
+ output current level as this value is the same regardless of
+ whether the regulator is enabled or disabled.
+
+
+What: /sys/class/regulator/.../opmode
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ opmode. This holds the regulator operating mode setting.
+
+ The opmode value can be one of the following strings:
+
+ 'fast'
+ 'normal'
+ 'idle'
+ 'standby'
+ 'unknown'
+
+ The modes are described in include/linux/regulator/regulator.h
+
+ NOTE: This value should not be used to determine the regulator
+ output operating mode as this value is the same regardless of
+ whether the regulator is enabled or disabled.
+
+
+What: /sys/class/regulator/.../min_microvolts
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ min_microvolts. This holds the minimum safe working regulator
+ output voltage setting for this domain measured in microvolts.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no min microvolts constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../max_microvolts
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ max_microvolts. This holds the maximum safe working regulator
+ output voltage setting for this domain measured in microvolts.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no max microvolts constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../min_microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ min_microamps. This holds the minimum safe working regulator
+ output current limit setting for this domain measured in
+ microamps.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no min microamps constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../max_microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ max_microamps. This holds the maximum safe working regulator
+ output current limit setting for this domain measured in
+ microamps.
+
+ NOTE: this will return the string 'constraint not defined' if
+ the power domain has no max microamps constraint defined by
+ platform code.
+
+
+What: /sys/class/regulator/.../num_users
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ num_users. This holds the number of consumer devices that
+ have called regulator_enable() on this regulator.
+
+
+What: /sys/class/regulator/.../requested_microamps
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ requested_microamps. This holds the total requested load
+ current in microamps for this regulator from all its consumer
+ devices.
+
+
+What: /sys/class/regulator/.../parent
+Date: April 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Some regulator directories will contain a link called parent.
+ This points to the parent or supply regulator if one exists.
+
+What: /sys/class/regulator/.../suspend_mem_microvolts
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_mem_microvolts. This holds the regulator output
+ voltage setting for this domain measured in microvolts when
+ the system is suspended to memory.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to memory voltage defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_disk_microvolts
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_disk_microvolts. This holds the regulator output
+ voltage setting for this domain measured in microvolts when
+ the system is suspended to disk.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to disk voltage defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_standby_microvolts
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_standby_microvolts. This holds the regulator output
+ voltage setting for this domain measured in microvolts when
+ the system is suspended to standby.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to standby voltage defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_mem_mode
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_mem_mode. This holds the regulator operating mode
+ setting for this domain when the system is suspended to
+ memory.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to memory mode defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_disk_mode
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_disk_mode. This holds the regulator operating mode
+ setting for this domain when the system is suspended to disk.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to disk mode defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_standby_mode
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_standby_mode. This holds the regulator operating mode
+ setting for this domain when the system is suspended to
+ standby.
+
+ NOTE: this will return the string 'not defined' if
+ the power domain has no suspend to standby mode defined by
+ platform code.
+
+What: /sys/class/regulator/.../suspend_mem_state
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_mem_state. This holds the regulator operating state
+ when suspended to memory.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'not defined'
+
+What: /sys/class/regulator/.../suspend_disk_state
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_disk_state. This holds the regulator operating state
+ when suspended to disk.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'not defined'
+
+What: /sys/class/regulator/.../suspend_standby_state
+Date: May 2008
+KernelVersion: 2.6.26
+Contact: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+Description:
+ Each regulator directory will contain a field called
+ suspend_standby_state. This holds the regulator operating
+ state when suspended to standby.
+
+ This will be one of the following strings:
+
+ 'enabled'
+ 'disabled'
+ 'not defined'
charge when battery considered full/empty at given conditions (temperature,
age)". I.e. these attributes represents real thresholds, not design values.
+CHARGE_COUNTER - the current charge counter (in µAh). This could easily
+be negative; there is no empty or full value. It is only useful for
+relative, time-based measurements.
+
ENERGY_FULL, ENERGY_EMPTY - same as above but for energy.
CAPACITY - capacity in percents.
--- /dev/null
+Regulator Consumer Driver Interface
+===================================
+
+This text describes the regulator interface for consumer device drivers.
+Please see overview.txt for a description of the terms used in this text.
+
+
+1. Consumer Regulator Access (static & dynamic drivers)
+=======================================================
+
+A consumer driver can get access to it's supply regulator by calling :-
+
+regulator = regulator_get(dev, "Vcc");
+
+The consumer passes in it's struct device pointer and power supply ID. The core
+then finds the correct regulator by consulting a machine specific lookup table.
+If the lookup is successful then this call will return a pointer to the struct
+regulator that supplies this consumer.
+
+To release the regulator the consumer driver should call :-
+
+regulator_put(regulator);
+
+Consumers can be supplied by more than one regulator e.g. codec consumer with
+analog and digital supplies :-
+
+digital = regulator_get(dev, "Vcc"); /* digital core */
+analog = regulator_get(dev, "Avdd"); /* analog */
+
+The regulator access functions regulator_get() and regulator_put() will
+usually be called in your device drivers probe() and remove() respectively.
+
+
+2. Regulator Output Enable & Disable (static & dynamic drivers)
+====================================================================
+
+A consumer can enable it's power supply by calling:-
+
+int regulator_enable(regulator);
+
+NOTE: The supply may already be enabled before regulator_enabled() is called.
+This may happen if the consumer shares the regulator or the regulator has been
+previously enabled by bootloader or kernel board initialization code.
+
+A consumer can determine if a regulator is enabled by calling :-
+
+int regulator_is_enabled(regulator);
+
+This will return > zero when the regulator is enabled.
+
+
+A consumer can disable it's supply when no longer needed by calling :-
+
+int regulator_disable(regulator);
+
+NOTE: This may not disable the supply if it's shared with other consumers. The
+regulator will only be disabled when the enabled reference count is zero.
+
+Finally, a regulator can be forcefully disabled in the case of an emergency :-
+
+int regulator_force_disable(regulator);
+
+NOTE: this will immediately and forcefully shutdown the regulator output. All
+consumers will be powered off.
+
+
+3. Regulator Voltage Control & Status (dynamic drivers)
+======================================================
+
+Some consumer drivers need to be able to dynamically change their supply
+voltage to match system operating points. e.g. CPUfreq drivers can scale
+voltage along with frequency to save power, SD drivers may need to select the
+correct card voltage, etc.
+
+Consumers can control their supply voltage by calling :-
+
+int regulator_set_voltage(regulator, min_uV, max_uV);
+
+Where min_uV and max_uV are the minimum and maximum acceptable voltages in
+microvolts.
+
+NOTE: this can be called when the regulator is enabled or disabled. If called
+when enabled, then the voltage changes instantly, otherwise the voltage
+configuration changes and the voltage is physically set when the regulator is
+next enabled.
+
+The regulators configured voltage output can be found by calling :-
+
+int regulator_get_voltage(regulator);
+
+NOTE: get_voltage() will return the configured output voltage whether the
+regulator is enabled or disabled and should NOT be used to determine regulator
+output state. However this can be used in conjunction with is_enabled() to
+determine the regulator physical output voltage.
+
+
+4. Regulator Current Limit Control & Status (dynamic drivers)
+===========================================================
+
+Some consumer drivers need to be able to dynamically change their supply
+current limit to match system operating points. e.g. LCD backlight driver can
+change the current limit to vary the backlight brightness, USB drivers may want
+to set the limit to 500mA when supplying power.
+
+Consumers can control their supply current limit by calling :-
+
+int regulator_set_current_limit(regulator, min_uV, max_uV);
+
+Where min_uA and max_uA are the minimum and maximum acceptable current limit in
+microamps.
+
+NOTE: this can be called when the regulator is enabled or disabled. If called
+when enabled, then the current limit changes instantly, otherwise the current
+limit configuration changes and the current limit is physically set when the
+regulator is next enabled.
+
+A regulators current limit can be found by calling :-
+
+int regulator_get_current_limit(regulator);
+
+NOTE: get_current_limit() will return the current limit whether the regulator
+is enabled or disabled and should not be used to determine regulator current
+load.
+
+
+5. Regulator Operating Mode Control & Status (dynamic drivers)
+=============================================================
+
+Some consumers can further save system power by changing the operating mode of
+their supply regulator to be more efficient when the consumers operating state
+changes. e.g. consumer driver is idle and subsequently draws less current
+
+Regulator operating mode can be changed indirectly or directly.
+
+Indirect operating mode control.
+--------------------------------
+Consumer drivers can request a change in their supply regulator operating mode
+by calling :-
+
+int regulator_set_optimum_mode(struct regulator *regulator, int load_uA);
+
+This will cause the core to recalculate the total load on the regulator (based
+on all it's consumers) and change operating mode (if necessary and permitted)
+to best match the current operating load.
+
+The load_uA value can be determined from the consumers datasheet. e.g.most
+datasheets have tables showing the max current consumed in certain situations.
+
+Most consumers will use indirect operating mode control since they have no
+knowledge of the regulator or whether the regulator is shared with other
+consumers.
+
+Direct operating mode control.
+------------------------------
+Bespoke or tightly coupled drivers may want to directly control regulator
+operating mode depending on their operating point. This can be achieved by
+calling :-
+
+int regulator_set_mode(struct regulator *regulator, unsigned int mode);
+unsigned int regulator_get_mode(struct regulator *regulator);
+
+Direct mode will only be used by consumers that *know* about the regulator and
+are not sharing the regulator with other consumers.
+
+
+6. Regulator Events
+===================
+Regulators can notify consumers of external events. Events could be received by
+consumers under regulator stress or failure conditions.
+
+Consumers can register interest in regulator events by calling :-
+
+int regulator_register_notifier(struct regulator *regulator,
+ struct notifier_block *nb);
+
+Consumers can uregister interest by calling :-
+
+int regulator_unregister_notifier(struct regulator *regulator,
+ struct notifier_block *nb);
+
+Regulators use the kernel notifier framework to send event to thier interested
+consumers.
--- /dev/null
+Regulator Machine Driver Interface
+===================================
+
+The regulator machine driver interface is intended for board/machine specific
+initialisation code to configure the regulator subsystem. Typical things that
+machine drivers would do are :-
+
+ 1. Regulator -> Device mapping.
+ 2. Regulator supply configuration.
+ 3. Power Domain constraint setting.
+
+
+
+1. Regulator -> device mapping
+==============================
+Consider the following machine :-
+
+ Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+ |
+ +-> [Consumer B @ 3.3V]
+
+The drivers for consumers A & B must be mapped to the correct regulator in
+order to control their power supply. This mapping can be achieved in machine
+initialisation code by calling :-
+
+int regulator_set_device_supply(const char *regulator, struct device *dev,
+ const char *supply);
+
+and is shown with the following code :-
+
+regulator_set_device_supply("Regulator-1", devB, "Vcc");
+regulator_set_device_supply("Regulator-2", devA, "Vcc");
+
+This maps Regulator-1 to the 'Vcc' supply for Consumer B and maps Regulator-2
+to the 'Vcc' supply for Consumer A.
+
+
+2. Regulator supply configuration.
+==================================
+Consider the following machine (again) :-
+
+ Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+ |
+ +-> [Consumer B @ 3.3V]
+
+Regulator-1 supplies power to Regulator-2. This relationship must be registered
+with the core so that Regulator-1 is also enabled when Consumer A enables it's
+supply (Regulator-2).
+
+This relationship can be register with the core via :-
+
+int regulator_set_supply(const char *regulator, const char *regulator_supply);
+
+In this example we would use the following code :-
+
+regulator_set_supply("Regulator-2", "Regulator-1");
+
+Relationships can be queried by calling :-
+
+const char *regulator_get_supply(const char *regulator);
+
+
+3. Power Domain constraint setting.
+===================================
+Each power domain within a system has physical constraints on voltage and
+current. This must be defined in software so that the power domain is always
+operated within specifications.
+
+Consider the following machine (again) :-
+
+ Regulator-1 -+-> Regulator-2 --> [Consumer A @ 1.8 - 2.0V]
+ |
+ +-> [Consumer B @ 3.3V]
+
+This gives us two regulators and two power domains:
+
+ Domain 1: Regulator-2, Consumer B.
+ Domain 2: Consumer A.
+
+Constraints can be registered by calling :-
+
+int regulator_set_platform_constraints(const char *regulator,
+ struct regulation_constraints *constraints);
+
+The example is defined as follows :-
+
+struct regulation_constraints domain_1 = {
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+};
+
+struct regulation_constraints domain_2 = {
+ .min_uV = 1800000,
+ .max_uV = 2000000,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ .valid_modes_mask = REGULATOR_MODE_NORMAL,
+};
+
+regulator_set_platform_constraints("Regulator-1", &domain_1);
+regulator_set_platform_constraints("Regulator-2", &domain_2);
--- /dev/null
+Linux voltage and current regulator framework
+=============================================
+
+About
+=====
+
+This framework is designed to provide a standard kernel interface to control
+voltage and current regulators.
+
+The intention is to allow systems to dynamically control regulator power output
+in order to save power and prolong battery life. This applies to both voltage
+regulators (where voltage output is controllable) and current sinks (where
+current limit is controllable).
+
+(C) 2008 Wolfson Microelectronics PLC.
+Author: Liam Girdwood <lg@opensource.wolfsonmicro.com>
+
+
+Nomenclature
+============
+
+Some terms used in this document:-
+
+ o Regulator - Electronic device that supplies power to other devices.
+ Most regulators can enable and disable their output whilst
+ some can control their output voltage and or current.
+
+ Input Voltage -> Regulator -> Output Voltage
+
+
+ o PMIC - Power Management IC. An IC that contains numerous regulators
+ and often contains other susbsystems.
+
+
+ o Consumer - Electronic device that is supplied power by a regulator.
+ Consumers can be classified into two types:-
+
+ Static: consumer does not change it's supply voltage or
+ current limit. It only needs to enable or disable it's
+ power supply. It's supply voltage is set by the hardware,
+ bootloader, firmware or kernel board initialisation code.
+
+ Dynamic: consumer needs to change it's supply voltage or
+ current limit to meet operation demands.
+
+
+ o Power Domain - Electronic circuit that is supplied it's input power by the
+ output power of a regulator, switch or by another power
+ domain.
+
+ The supply regulator may be behind a switch(s). i.e.
+
+ Regulator -+-> Switch-1 -+-> Switch-2 --> [Consumer A]
+ | |
+ | +-> [Consumer B], [Consumer C]
+ |
+ +-> [Consumer D], [Consumer E]
+
+ That is one regulator and three power domains:
+
+ Domain 1: Switch-1, Consumers D & E.
+ Domain 2: Switch-2, Consumers B & C.
+ Domain 3: Consumer A.
+
+ and this represents a "supplies" relationship:
+
+ Domain-1 --> Domain-2 --> Domain-3.
+
+ A power domain may have regulators that are supplied power
+ by other regulators. i.e.
+
+ Regulator-1 -+-> Regulator-2 -+-> [Consumer A]
+ |
+ +-> [Consumer B]
+
+ This gives us two regulators and two power domains:
+
+ Domain 1: Regulator-2, Consumer B.
+ Domain 2: Consumer A.
+
+ and a "supplies" relationship:
+
+ Domain-1 --> Domain-2
+
+
+ o Constraints - Constraints are used to define power levels for performance
+ and hardware protection. Constraints exist at three levels:
+
+ Regulator Level: This is defined by the regulator hardware
+ operating parameters and is specified in the regulator
+ datasheet. i.e.
+
+ - voltage output is in the range 800mV -> 3500mV.
+ - regulator current output limit is 20mA @ 5V but is
+ 10mA @ 10V.
+
+ Power Domain Level: This is defined in software by kernel
+ level board initialisation code. It is used to constrain a
+ power domain to a particular power range. i.e.
+
+ - Domain-1 voltage is 3300mV
+ - Domain-2 voltage is 1400mV -> 1600mV
+ - Domain-3 current limit is 0mA -> 20mA.
+
+ Consumer Level: This is defined by consumer drivers
+ dynamically setting voltage or current limit levels.
+
+ e.g. a consumer backlight driver asks for a current increase
+ from 5mA to 10mA to increase LCD illumination. This passes
+ to through the levels as follows :-
+
+ Consumer: need to increase LCD brightness. Lookup and
+ request next current mA value in brightness table (the
+ consumer driver could be used on several different
+ personalities based upon the same reference device).
+
+ Power Domain: is the new current limit within the domain
+ operating limits for this domain and system state (e.g.
+ battery power, USB power)
+
+ Regulator Domains: is the new current limit within the
+ regulator operating parameters for input/ouput voltage.
+
+ If the regulator request passes all the constraint tests
+ then the new regulator value is applied.
+
+
+Design
+======
+
+The framework is designed and targeted at SoC based devices but may also be
+relevant to non SoC devices and is split into the following four interfaces:-
+
+
+ 1. Consumer driver interface.
+
+ This uses a similar API to the kernel clock interface in that consumer
+ drivers can get and put a regulator (like they can with clocks atm) and
+ get/set voltage, current limit, mode, enable and disable. This should
+ allow consumers complete control over their supply voltage and current
+ limit. This also compiles out if not in use so drivers can be reused in
+ systems with no regulator based power control.
+
+ See Documentation/power/regulator/consumer.txt
+
+ 2. Regulator driver interface.
+
+ This allows regulator drivers to register their regulators and provide
+ operations to the core. It also has a notifier call chain for propagating
+ regulator events to clients.
+
+ See Documentation/power/regulator/regulator.txt
+
+ 3. Machine interface.
+
+ This interface is for machine specific code and allows the creation of
+ voltage/current domains (with constraints) for each regulator. It can
+ provide regulator constraints that will prevent device damage through
+ overvoltage or over current caused by buggy client drivers. It also
+ allows the creation of a regulator tree whereby some regulators are
+ supplied by others (similar to a clock tree).
+
+ See Documentation/power/regulator/machine.txt
+
+ 4. Userspace ABI.
+
+ The framework also exports a lot of useful voltage/current/opmode data to
+ userspace via sysfs. This could be used to help monitor device power
+ consumption and status.
+
+ See Documentation/ABI/testing/regulator-sysfs.txt
--- /dev/null
+Regulator Driver Interface
+==========================
+
+The regulator driver interface is relatively simple and designed to allow
+regulator drivers to register their services with the core framework.
+
+
+Registration
+============
+
+Drivers can register a regulator by calling :-
+
+struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
+ void *reg_data);
+
+This will register the regulators capabilities and operations the regulator
+core. The core does not touch reg_data (private to regulator driver).
+
+Regulators can be unregistered by calling :-
+
+void regulator_unregister(struct regulator_dev *rdev);
+
+
+Regulator Events
+================
+Regulators can send events (e.g. over temp, under voltage, etc) to consumer
+drivers by calling :-
+
+int regulator_notifier_call_chain(struct regulator_dev *rdev,
+ unsigned long event, void *data);
- MPC5200 Device Tree Bindings
ppc_htab.txt
- info about the Linux/PPC /proc/ppc_htab entry
-SBC8260_memory_mapping.txt
- - EST SBC8260 board info
smp.txt
- use and state info about Linux/PPC on MP machines
sound.txt
+++ /dev/null
-Please mail me (Jon Diekema, diekema_jon@si.com or diekema@cideas.com)
-if you have questions, comments or corrections.
-
- * EST SBC8260 Linux memory mapping rules
-
- http://www.estc.com/
- http://www.estc.com/products/boards/SBC8260-8240_ds.html
-
- Initial conditions:
- -------------------
-
- Tasks that need to be perform by the boot ROM before control is
- transferred to zImage (compressed Linux kernel):
-
- - Define the IMMR to 0xf0000000
-
- - Initialize the memory controller so that RAM is available at
- physical address 0x00000000. On the SBC8260 is this 16M (64M)
- SDRAM.
-
- - The boot ROM should only clear the RAM that it is using.
-
- The reason for doing this is to enhances the chances of a
- successful post mortem on a Linux panic. One of the first
- items to examine is the 16k (LOG_BUF_LEN) circular console
- buffer called log_buf which is defined in kernel/printk.c.
-
- - To enhance boot ROM performance, the I-cache can be enabled.
-
- Date: Mon, 22 May 2000 14:21:10 -0700
- From: Neil Russell <caret@c-side.com>
-
- LiMon (LInux MONitor) runs with and starts Linux with MMU
- off, I-cache enabled, D-cache disabled. The I-cache doesn't
- need hints from the MMU to work correctly as the D-cache
- does. No D-cache means no special code to handle devices in
- the presence of cache (no snooping, etc). The use of the
- I-cache means that the monitor can run acceptably fast
- directly from ROM, rather than having to copy it to RAM.
-
- - Build the board information structure (see
- include/asm-ppc/est8260.h for its definition)
-
- - The compressed Linux kernel (zImage) contains a bootstrap loader
- that is position independent; you can load it into any RAM,
- ROM or FLASH memory address >= 0x00500000 (above 5 MB), or
- at its link address of 0x00400000 (4 MB).
-
- Note: If zImage is loaded at its link address of 0x00400000 (4 MB),
- then zImage will skip the step of moving itself to
- its link address.
-
- - Load R3 with the address of the board information structure
-
- - Transfer control to zImage
-
- - The Linux console port is SMC1, and the baud rate is controlled
- from the bi_baudrate field of the board information structure.
- On thing to keep in mind when picking the baud rate, is that
- there is no flow control on the SMC ports. I would stick
- with something safe and standard like 19200.
-
- On the EST SBC8260, the SMC1 port is on the COM1 connector of
- the board.
-
-
- EST SBC8260 defaults:
- ---------------------
-
- Chip
- Memory Sel Bus Use
- --------------------- --- --- ----------------------------------
- 0x00000000-0x03FFFFFF CS2 60x (16M or 64M)/64M SDRAM
- 0x04000000-0x04FFFFFF CS4 local 4M/16M SDRAM (soldered to the board)
- 0x21000000-0x21000000 CS7 60x 1B/64K Flash present detect (from the flash SIMM)
- 0x21000001-0x21000001 CS7 60x 1B/64K Switches (read) and LEDs (write)
- 0x22000000-0x2200FFFF CS5 60x 8K/64K EEPROM
- 0xFC000000-0xFCFFFFFF CS6 60x 2M/16M flash (8 bits wide, soldered to the board)
- 0xFE000000-0xFFFFFFFF CS0 60x 4M/16M flash (SIMM)
-
- Notes:
- ------
-
- - The chip selects can map 32K blocks and up (powers of 2)
-
- - The SDRAM machine can handled up to 128Mbytes per chip select
-
- - Linux uses the 60x bus memory (the SDRAM DIMM) for the
- communications buffers.
-
- - BATs can map 128K-256Mbytes each. There are four data BATs and
- four instruction BATs. Generally the data and instruction BATs
- are mapped the same.
-
- - The IMMR must be set above the kernel virtual memory addresses,
- which start at 0xC0000000. Otherwise, the kernel may crash as
- soon as you start any threads or processes due to VM collisions
- in the kernel or user process space.
-
-
- Details from Dan Malek <dan_malek@mvista.com> on 10/29/1999:
-
- The user application virtual space consumes the first 2 Gbytes
- (0x00000000 to 0x7FFFFFFF). The kernel virtual text starts at
- 0xC0000000, with data following. There is a "protection hole"
- between the end of kernel data and the start of the kernel
- dynamically allocated space, but this space is still within
- 0xCxxxxxxx.
-
- Obviously the kernel can't map any physical addresses 1:1 in
- these ranges.
-
-
- Details from Dan Malek <dan_malek@mvista.com> on 5/19/2000:
-
- During the early kernel initialization, the kernel virtual
- memory allocator is not operational. Prior to this KVM
- initialization, we choose to map virtual to physical addresses
- 1:1. That is, the kernel virtual address exactly matches the
- physical address on the bus. These mappings are typically done
- in arch/ppc/kernel/head.S, or arch/ppc/mm/init.c. Only
- absolutely necessary mappings should be done at this time, for
- example board control registers or a serial uart. Normal device
- driver initialization should map resources later when necessary.
-
- Although platform dependent, and certainly the case for embedded
- 8xx, traditionally memory is mapped at physical address zero,
- and I/O devices above physical address 0x80000000. The lowest
- and highest (above 0xf0000000) I/O addresses are traditionally
- used for devices or registers we need to map during kernel
- initialization and prior to KVM operation. For this reason,
- and since it followed prior PowerPC platform examples, I chose
- to map the embedded 8xx kernel to the 0xc0000000 virtual address.
- This way, we can enable the MMU to map the kernel for proper
- operation, and still map a few windows before the KVM is operational.
-
- On some systems, you could possibly run the kernel at the
- 0x80000000 or any other virtual address. It just depends upon
- mapping that must be done prior to KVM operational. You can never
- map devices or kernel spaces that overlap with the user virtual
- space. This is why default IMMR mapping used by most BDM tools
- won't work. They put the IMMR at something like 0x10000000 or
- 0x02000000 for example. You simply can't map these addresses early
- in the kernel, and continue proper system operation.
-
- The embedded 8xx/82xx kernel is mature enough that all you should
- need to do is map the IMMR someplace at or above 0xf0000000 and it
- should boot far enough to get serial console messages and KGDB
- connected on any platform. There are lots of other subtle memory
- management design features that you simply don't need to worry
- about. If you are changing functions related to MMU initialization,
- you are likely breaking things that are known to work and are
- heading down a path of disaster and frustration. Your changes
- should be to make the flexibility of the processor fit Linux,
- not force arbitrary and non-workable memory mappings into Linux.
-
- - You don't want to change KERNELLOAD or KERNELBASE, otherwise the
- virtual memory and MMU code will get confused.
-
- arch/ppc/Makefile:KERNELLOAD = 0xc0000000
-
- include/asm-ppc/page.h:#define PAGE_OFFSET 0xc0000000
- include/asm-ppc/page.h:#define KERNELBASE PAGE_OFFSET
-
- - RAM is at physical address 0x00000000, and gets mapped to
- virtual address 0xC0000000 for the kernel.
-
-
- Physical addresses used by the Linux kernel:
- --------------------------------------------
-
- 0x00000000-0x3FFFFFFF 1GB reserved for RAM
- 0xF0000000-0xF001FFFF 128K IMMR 64K used for dual port memory,
- 64K for 8260 registers
-
-
- Logical addresses used by the Linux kernel:
- -------------------------------------------
-
- 0xF0000000-0xFFFFFFFF 256M BAT0 (IMMR: dual port RAM, registers)
- 0xE0000000-0xEFFFFFFF 256M BAT1 (I/O space for custom boards)
- 0xC0000000-0xCFFFFFFF 256M BAT2 (RAM)
- 0xD0000000-0xDFFFFFFF 256M BAT3 (if RAM > 256MByte)
-
-
- EST SBC8260 Linux mapping:
- --------------------------
-
- DBAT0, IBAT0, cache inhibited:
-
- Chip
- Memory Sel Use
- --------------------- --- ---------------------------------
- 0xF0000000-0xF001FFFF n/a IMMR: dual port RAM, registers
-
- DBAT1, IBAT1, cache inhibited:
-
- fsl,cpm2-scc-uart
- fsl,qe-uart
+Modem control lines connected to GPIO controllers are listed in the gpios
+property as described in booting-without-of.txt, section IX.1 in the following
+order:
+
+CTS, RTS, DCD, DSR, DTR, and RI.
+
+The gpios property is optional and can be left out when control lines are
+not used.
+
Example:
serial@11a00 {
interrupt-parent = <&PIC>;
fsl,cpm-brg = <1>;
fsl,cpm-command = <00800000>;
+ gpios = <&gpio_c 15 0
+ &gpio_d 29 0>;
};
rfkill input line is active. Only if none of the rfkill input lines are
active, will it return RFKILL_STATE_UNBLOCKED.
-If it doesn't implement the get_state() hook, it must make sure that its calls
-to rfkill_force_state() are enough to keep the status always up-to-date, and it
-must do a rfkill_force_state() on resume from sleep.
+Since the device has a hardware rfkill line, it IS subject to state changes
+external to rfkill. Therefore, the driver must make sure that it calls
+rfkill_force_state() to keep the status always up-to-date, and it must do a
+rfkill_force_state() on resume from sleep.
Every time the driver gets a notification from the card that one of its rfkill
lines changed state (polling might be needed on badly designed cards that don't
about its current state).
The rfkill class will call the get_state hook of a device every time it needs
-to know the *real* current state of the hardware. This can happen often.
+to know the *real* current state of the hardware. This can happen often, but
+it does not do any polling, so it is not enough on hardware that is subject
+to state changes outside of the rfkill subsystem.
+
+Therefore, calling rfkill_force_state() when a state change happens is
+mandatory when the device has a hardware rfkill line, or when something else
+like the firmware could cause its state to be changed without going through the
+rfkill class.
Some hardware provides events when its status changes. In these cases, it is
best for the driver to not provide a get_state hook, and instead register the
rfkill class *already* with the correct status, and keep it updated using
rfkill_force_state() when it gets an event from the hardware.
+rfkill_force_state() must be used on the device resume handlers to update the
+rfkill status, should there be any chance of the device status changing during
+the sleep.
+
There is no provision for a statically-allocated rfkill struct. You must
use rfkill_allocate() to allocate one.
L: linux-sh@vger.kernel.org
W: http://www.linux-sh.org
T: git kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6.git
-S: Maintained
+S: Supported
SUN3/3X
P: Sam Creasey
L: netdev@vger.kernel.org
S: Maintained
+VOLTAGE AND CURRENT REGULATOR FRAMEWORK
+P: Liam Girdwood
+M: lg@opensource.wolfsonmicro.com
+P: Mark Brown
+M: broonie@opensource.wolfsonmicro.com
+W: http://opensource.wolfsonmicro.com/node/15
+T: git kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6.git
+S: Supported
+
VT1211 HARDWARE MONITOR DRIVER
P: Juerg Haefliger
M: juergh@gmail.com
source "drivers/dca/Kconfig"
+source "drivers/regulator/Kconfig"
+
source "drivers/uio/Kconfig"
endmenu
#include <linux/mm.h>
#include <linux/hugetlb.h>
#include <linux/pagemap.h>
+#include <linux/module.h>
#include <linux/slab.h>
#include <linux/sysctl.h>
#include <linux/log2.h>
#include <asm/tlb.h>
#include <asm/tlbflush.h>
-unsigned int hpage_shift=HPAGE_SHIFT_DEFAULT;
+unsigned int hpage_shift = HPAGE_SHIFT_DEFAULT;
+EXPORT_SYMBOL(hpage_shift);
pte_t *
huge_pte_alloc(struct mm_struct *mm, unsigned long addr, unsigned long sz)
default y
select HAVE_IDE
select HAVE_OPROFILE
+ select HAVE_ARCH_KGDB
# Horrible source of confusion. Die, die, die ...
select EMBEDDED
select RTC_LIB
select SYS_HAS_CPU_RM9000
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
help
The eXcite is a smart camera platform manufactured by
Basler Vision Technologies AG.
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
select IRQ_CPU
select SERIAL_8250
select SERIAL_8250_CONSOLE
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_SMP
help
Yosemite is an evaluation board for the RM9000x2 processor
select SYS_HAS_CPU_R10000
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_NUMA
select SYS_SUPPORTS_SMP
select GENERIC_HARDIRQS_NO__DO_IRQ
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_LITTLE_ENDIAN
select ZONE_DMA32 if 64BIT
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select GENERIC_HARDIRQS_NO__DO_IRQ
- select SYS_SUPPORTS_KGDB
select GENERIC_GPIO
config SWAP_IO_SPACE
arch/mips/kernel/smtc.c. This debugging option result in significant
overhead so should be disabled in production kernels.
-config KGDB
- bool "Remote GDB kernel debugging"
- depends on DEBUG_KERNEL && SYS_SUPPORTS_KGDB
- select DEBUG_INFO
- help
- If you say Y here, it will be possible to remotely debug the MIPS
- kernel using gdb. This enlarges your kernel image disk size by
- several megabytes and requires a machine with more than 16 MB,
- better 32 MB RAM to avoid excessive linking time. This is only
- useful for kernel hackers. If unsure, say N.
-
-config SYS_SUPPORTS_KGDB
- bool
-
-config GDB_CONSOLE
- bool "Console output to GDB"
- depends on KGDB
- help
- If you are using GDB for remote debugging over a serial port and
- would like kernel messages to be formatted into GDB $O packets so
- that GDB prints them as program output, say 'Y'.
-
config SB1XXX_CORELIS
bool "Corelis Debugger"
depends on SIBYTE_SB1xxx_SOC
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_APM_EMULATION
- select SYS_SUPPORTS_KGDB
au1xxx_irqmap.o clocks.o platform.o power.o setup.o \
sleeper.o cputable.o dma.o dbdma.o gpio.o
-obj-$(CONFIG_KGDB) += dbg_io.o
obj-$(CONFIG_PCI) += pci.o
EXTRA_CFLAGS += -Werror
+++ /dev/null
-#include <linux/types.h>
-
-#include <asm/mach-au1x00/au1000.h>
-
-#ifdef CONFIG_KGDB
-
-/*
- * FIXME the user should be able to select the
- * uart to be used for debugging.
- */
-#define DEBUG_BASE UART_DEBUG_BASE
-
-#define UART16550_BAUD_2400 2400
-#define UART16550_BAUD_4800 4800
-#define UART16550_BAUD_9600 9600
-#define UART16550_BAUD_19200 19200
-#define UART16550_BAUD_38400 38400
-#define UART16550_BAUD_57600 57600
-#define UART16550_BAUD_115200 115200
-
-#define UART16550_PARITY_NONE 0
-#define UART16550_PARITY_ODD 0x08
-#define UART16550_PARITY_EVEN 0x18
-#define UART16550_PARITY_MARK 0x28
-#define UART16550_PARITY_SPACE 0x38
-
-#define UART16550_DATA_5BIT 0x0
-#define UART16550_DATA_6BIT 0x1
-#define UART16550_DATA_7BIT 0x2
-#define UART16550_DATA_8BIT 0x3
-
-#define UART16550_STOP_1BIT 0x0
-#define UART16550_STOP_2BIT 0x4
-
-
-#define UART_RX 0 /* Receive buffer */
-#define UART_TX 4 /* Transmit buffer */
-#define UART_IER 8 /* Interrupt Enable Register */
-#define UART_IIR 0xC /* Interrupt ID Register */
-#define UART_FCR 0x10 /* FIFO Control Register */
-#define UART_LCR 0x14 /* Line Control Register */
-#define UART_MCR 0x18 /* Modem Control Register */
-#define UART_LSR 0x1C /* Line Status Register */
-#define UART_MSR 0x20 /* Modem Status Register */
-#define UART_CLK 0x28 /* Baud Rat4e Clock Divider */
-#define UART_MOD_CNTRL 0x100 /* Module Control */
-
-/* memory-mapped read/write of the port */
-#define UART16550_READ(y) (au_readl(DEBUG_BASE + y) & 0xff)
-#define UART16550_WRITE(y, z) (au_writel(z & 0xff, DEBUG_BASE + y))
-
-extern unsigned long calc_clock(void);
-
-void debugInit(u32 baud, u8 data, u8 parity, u8 stop)
-{
- if (UART16550_READ(UART_MOD_CNTRL) != 0x3)
- UART16550_WRITE(UART_MOD_CNTRL, 3);
- calc_clock();
-
- /* disable interrupts */
- UART16550_WRITE(UART_IER, 0);
-
- /* set up baud rate */
- {
- u32 divisor;
-
- /* set divisor */
- divisor = get_au1x00_uart_baud_base() / baud;
- UART16550_WRITE(UART_CLK, divisor & 0xffff);
- }
-
- /* set data format */
- UART16550_WRITE(UART_LCR, (data | parity | stop));
-}
-
-static int remoteDebugInitialized;
-
-u8 getDebugChar(void)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_115200,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE,
- UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(UART_LSR) & 0x1) == 0);
- return UART16550_READ(UART_RX);
-}
-
-
-int putDebugChar(u8 byte)
-{
- if (!remoteDebugInitialized) {
- remoteDebugInitialized = 1;
- debugInit(UART16550_BAUD_115200,
- UART16550_DATA_8BIT,
- UART16550_PARITY_NONE,
- UART16550_STOP_1BIT);
- }
-
- while ((UART16550_READ(UART_LSR) & 0x40) == 0);
- UART16550_WRITE(UART_TX, byte);
-
- return 1;
-}
-
-#endif
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x08000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x08000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
if (!memsize_str)
memsize = 0x04000000;
else
- memsize = strict_strtol(memsize_str, 0, NULL);
+ strict_strtol(memsize_str, 0, &memsize);
add_memory_region(0, memsize, BOOT_MEM_RAM);
}
obj-$(CONFIG_BASLER_EXCITE) += excite_irq.o excite_prom.o excite_setup.o \
excite_device.o excite_procfs.o
-obj-$(CONFIG_KGDB) += excite_dbg_io.o
obj-m += excite_iodev.o
+++ /dev/null
-/*
- * Copyright (C) 2004 by Basler Vision Technologies AG
- * Author: Thomas Koeller <thomas.koeller@baslerweb.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/linkage.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <asm/gdb-stub.h>
-#include <asm/rm9k-ocd.h>
-#include <excite.h>
-
-#if defined(CONFIG_SERIAL_8250) && CONFIG_SERIAL_8250_NR_UARTS > 1
-#error Debug port used by serial driver
-#endif
-
-#define UART_CLK 25000000
-#define BASE_BAUD (UART_CLK / 16)
-#define REGISTER_BASE_0 0x0208UL
-#define REGISTER_BASE_1 0x0238UL
-
-#define REGISTER_BASE_DBG REGISTER_BASE_1
-
-#define CPRR 0x0004
-#define UACFG 0x0200
-#define UAINTS 0x0204
-#define UARBR (REGISTER_BASE_DBG + 0x0000)
-#define UATHR (REGISTER_BASE_DBG + 0x0004)
-#define UADLL (REGISTER_BASE_DBG + 0x0008)
-#define UAIER (REGISTER_BASE_DBG + 0x000c)
-#define UADLH (REGISTER_BASE_DBG + 0x0010)
-#define UAIIR (REGISTER_BASE_DBG + 0x0014)
-#define UAFCR (REGISTER_BASE_DBG + 0x0018)
-#define UALCR (REGISTER_BASE_DBG + 0x001c)
-#define UAMCR (REGISTER_BASE_DBG + 0x0020)
-#define UALSR (REGISTER_BASE_DBG + 0x0024)
-#define UAMSR (REGISTER_BASE_DBG + 0x0028)
-#define UASCR (REGISTER_BASE_DBG + 0x002c)
-
-#define PARITY_NONE 0
-#define PARITY_ODD 0x08
-#define PARITY_EVEN 0x18
-#define PARITY_MARK 0x28
-#define PARITY_SPACE 0x38
-
-#define DATA_5BIT 0x0
-#define DATA_6BIT 0x1
-#define DATA_7BIT 0x2
-#define DATA_8BIT 0x3
-
-#define STOP_1BIT 0x0
-#define STOP_2BIT 0x4
-
-#define BAUD_DBG 57600
-#define PARITY_DBG PARITY_NONE
-#define DATA_DBG DATA_8BIT
-#define STOP_DBG STOP_1BIT
-
-/* Initialize the serial port for KGDB debugging */
-void __init excite_kgdb_init(void)
-{
- const u32 divisor = BASE_BAUD / BAUD_DBG;
-
- /* Take the UART out of reset */
- titan_writel(0x00ff1cff, CPRR);
- titan_writel(0x00000000, UACFG);
- titan_writel(0x00000002, UACFG);
-
- titan_writel(0x0, UALCR);
- titan_writel(0x0, UAIER);
-
- /* Disable FIFOs */
- titan_writel(0x00, UAFCR);
-
- titan_writel(0x80, UALCR);
- titan_writel(divisor & 0xff, UADLL);
- titan_writel((divisor & 0xff00) >> 8, UADLH);
- titan_writel(0x0, UALCR);
-
- titan_writel(DATA_DBG | PARITY_DBG | STOP_DBG, UALCR);
-
- /* Enable receiver interrupt */
- titan_readl(UARBR);
- titan_writel(0x1, UAIER);
-}
-
-int getDebugChar(void)
-{
- while (!(titan_readl(UALSR) & 0x1));
- return titan_readl(UARBR);
-}
-
-int putDebugChar(int data)
-{
- while (!(titan_readl(UALSR) & 0x20));
- titan_writel(data, UATHR);
- return 1;
-}
-
-/* KGDB interrupt handler */
-asmlinkage void excite_kgdb_inthdl(void)
-{
- if (unlikely(
- ((titan_readl(UAIIR) & 0x7) == 4)
- && ((titan_readl(UARBR) & 0xff) == 0x3)))
- set_async_breakpoint(®s->cp0_epc);
-}
mips_cpu_irq_init();
rm7k_cpu_irq_init();
rm9k_cpu_irq_init();
-
-#ifdef CONFIG_KGDB
- excite_kgdb_init();
-#endif
}
asmlinkage void plat_irq_dispatch(void)
msgint = msgintflags & msgintmask & (0x1 << (TITAN_MSGINT % 0x20));
if ((pending & (1 << TITAN_IRQ)) && msgint) {
ocd_writel(msgint, INTP0Clear0 + (TITAN_MSGINT / 0x20 * 0x10));
-#if defined(CONFIG_KGDB)
- excite_kgdb_inthdl();
-#endif
do_IRQ(TITAN_IRQ);
return;
}
/* Take the DUART out of reset */
titan_writel(0x00ff1cff, CPRR);
-#if defined(CONFIG_KGDB) || (CONFIG_SERIAL_8250_NR_UARTS > 1)
+#if (CONFIG_SERIAL_8250_NR_UARTS > 1)
/* Enable both ports */
titan_writel(MASK_SER0 | MASK_SER1, UACFG);
#else
/* Enable port #0 only */
titan_writel(MASK_SER0, UACFG);
-#endif /* defined(CONFIG_KGDB) */
+#endif
/*
* Set up serial port #0. Do not use autodetection; the result is
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.23-rc5
-# Thu Sep 6 13:14:29 2007
+# Linux kernel version: 2.6.26
+# Fri Jul 25 10:25:34 2008
#
CONFIG_MIPS=y
#
# CONFIG_MACH_ALCHEMY is not set
# CONFIG_BASLER_EXCITE is not set
+# CONFIG_BCM47XX is not set
CONFIG_MIPS_COBALT=y
# CONFIG_MACH_DECSTATION is not set
# CONFIG_MACH_JAZZ is not set
+# CONFIG_LASAT is not set
# CONFIG_LEMOTE_FULONG is not set
# CONFIG_MIPS_MALTA is not set
# CONFIG_MIPS_SIM is not set
# CONFIG_PMC_YOSEMITE is not set
# CONFIG_SGI_IP22 is not set
# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
# CONFIG_SGI_IP32 is not set
# CONFIG_SIBYTE_CRHINE is not set
# CONFIG_SIBYTE_CARMEL is not set
# CONFIG_SIBYTE_SENTOSA is not set
# CONFIG_SIBYTE_BIGSUR is not set
# CONFIG_SNI_RM is not set
-# CONFIG_TOSHIBA_JMR3927 is not set
-# CONFIG_TOSHIBA_RBTX4927 is not set
-# CONFIG_TOSHIBA_RBTX4938 is not set
+# CONFIG_MACH_TX39XX is not set
+# CONFIG_MACH_TX49XX is not set
+# CONFIG_MIKROTIK_RB532 is not set
# CONFIG_WR_PPMC is not set
CONFIG_RWSEM_GENERIC_SPINLOCK=y
# CONFIG_ARCH_HAS_ILOG2_U32 is not set
# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_TIME=y
+CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_CEVT_GT641XX=y
+CONFIG_CEVT_R4K=y
+CONFIG_CSRC_R4K=y
CONFIG_DMA_NONCOHERENT=y
CONFIG_DMA_NEED_PCI_MAP_STATE=y
CONFIG_EARLY_PRINTK=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_ARCH_FLATMEM_ENABLE=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
CONFIG_SELECT_MEMORY_MODEL=y
CONFIG_FLATMEM_MANUAL=y
# CONFIG_DISCONTIGMEM_MANUAL is not set
CONFIG_FLATMEM=y
CONFIG_FLAT_NODE_MEM_MAP=y
# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_SPLIT_PTLOCK_CPUS=4
# CONFIG_RESOURCES_64BIT is not set
CONFIG_ZONE_DMA_FLAG=0
CONFIG_VIRT_TO_BUS=y
+# CONFIG_TICK_ONESHOT is not set
+# CONFIG_NO_HZ is not set
+# CONFIG_HIGH_RES_TIMERS is not set
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
# CONFIG_HZ_48 is not set
# CONFIG_HZ_100 is not set
# CONFIG_HZ_128 is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-# CONFIG_USER_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_CGROUPS is not set
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
CONFIG_RELAY=y
+# CONFIG_NAMESPACES is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
CONFIG_SYSCTL_SYSCALL=y
+CONFIG_SYSCTL_SYSCALL_CHECK=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_HOTPLUG=y
CONFIG_PRINTK=y
CONFIG_BUG=y
CONFIG_ELF_CORE=y
+CONFIG_PCSPKR_PLATFORM=y
+CONFIG_COMPAT_BRK=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_ANON_INODES=y
CONFIG_EVENTFD=y
CONFIG_SHMEM=y
CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_SLAB=y
-# CONFIG_SLUB is not set
+CONFIG_SLUB_DEBUG=y
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_HAVE_IOREMAP_PROT is not set
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+# CONFIG_HAVE_DMA_ATTRS is not set
+# CONFIG_USE_GENERIC_SMP_HELPERS is not set
+# CONFIG_HAVE_CLK is not set
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SLABINFO=y
CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
CONFIG_MODULES=y
+# CONFIG_MODULE_FORCE_LOAD is not set
CONFIG_MODULE_UNLOAD=y
# CONFIG_MODULE_FORCE_UNLOAD is not set
# CONFIG_MODVERSIONS is not set
# CONFIG_MODULE_SRCVERSION_ALL is not set
-# CONFIG_KMOD is not set
+CONFIG_KMOD=y
CONFIG_BLOCK=y
# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
# CONFIG_LSF is not set
# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_BLK_DEV_INTEGRITY is not set
#
# IO Schedulers
# CONFIG_DEFAULT_CFQ is not set
# CONFIG_DEFAULT_NOOP is not set
CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_CLASSIC_RCU=y
#
# Bus options (PCI, PCMCIA, EISA, ISA, TC)
#
CONFIG_HW_HAS_PCI=y
CONFIG_PCI=y
+CONFIG_PCI_DOMAINS=y
# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_PCI_LEGACY=y
CONFIG_MMU=y
-
-#
-# PCCARD (PCMCIA/CardBus) support
-#
+CONFIG_I8253=y
# CONFIG_PCCARD is not set
# CONFIG_HOTPLUG_PCI is not set
#
# Power management options
#
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
# CONFIG_PM is not set
-CONFIG_SUSPEND_UP_POSSIBLE=y
#
# Networking
CONFIG_XFRM_USER=y
# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_XFRM_MIGRATE=y
+# CONFIG_XFRM_STATISTICS is not set
CONFIG_NET_KEY=y
CONFIG_NET_KEY_MIGRATE=y
CONFIG_INET=y
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
CONFIG_INET_XFRM_MODE_BEET=y
+# CONFIG_INET_LRO is not set
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_DEFAULT_TCP_CONG="cubic"
# CONFIG_TCP_MD5SIG is not set
# CONFIG_IPV6 is not set
-# CONFIG_INET6_XFRM_TUNNEL is not set
-# CONFIG_INET6_TUNNEL is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_IP_DCCP is not set
# CONFIG_LAPB is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
-
-#
-# QoS and/or fair queueing
-#
# CONFIG_NET_SCHED is not set
#
#
# CONFIG_NET_PKTGEN is not set
# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
# CONFIG_IRDA is not set
# CONFIG_BT is not set
# CONFIG_AF_RXRPC is not set
#
# Generic Driver Options
#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_STANDALONE=y
CONFIG_PREVENT_FIRMWARE_BUILD=y
CONFIG_FW_LOADER=y
+CONFIG_FIRMWARE_IN_KERNEL=y
+CONFIG_EXTRA_FIRMWARE=""
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_CONNECTOR is not set
CONFIG_MTD=y
CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_REDBOOT_PARTS is not set
# CONFIG_MTD_CMDLINE_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
#
# User Modules And Translation Layers
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
#
# RAM/ROM/Flash chip drivers
CONFIG_MTD_PHYSMAP_START=0x0
CONFIG_MTD_PHYSMAP_LEN=0x0
CONFIG_MTD_PHYSMAP_BANKWIDTH=0
+# CONFIG_MTD_INTEL_VR_NOR is not set
# CONFIG_MTD_PLATRAM is not set
#
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
+# CONFIG_BLK_DEV_HD is not set
# CONFIG_MISC_DEVICES is not set
+CONFIG_HAVE_IDE=y
# CONFIG_IDE is not set
#
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
CONFIG_ATA=y
# CONFIG_ATA_NONSTANDARD is not set
+CONFIG_SATA_PMP=y
# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SIL24 is not set
+CONFIG_ATA_SFF=y
# CONFIG_SATA_SVW is not set
# CONFIG_ATA_PIIX is not set
# CONFIG_SATA_MV is not set
# CONFIG_SATA_PROMISE is not set
# CONFIG_SATA_SX4 is not set
# CONFIG_SATA_SIL is not set
-# CONFIG_SATA_SIL24 is not set
# CONFIG_SATA_SIS is not set
# CONFIG_SATA_ULI is not set
# CONFIG_SATA_VIA is not set
# CONFIG_PATA_MPIIX is not set
# CONFIG_PATA_OLDPIIX is not set
# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NINJA32 is not set
# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_NS87415 is not set
# CONFIG_PATA_OPTI is not set
# CONFIG_PATA_OPTIDMA is not set
# CONFIG_PATA_PDC_OLD is not set
CONFIG_PATA_VIA=y
# CONFIG_PATA_WINBOND is not set
# CONFIG_PATA_PLATFORM is not set
+# CONFIG_PATA_SCH is not set
# CONFIG_MD is not set
+# CONFIG_FUSION is not set
#
-# Fusion MPT device support
+# IEEE 1394 (FireWire) support
#
-# CONFIG_FUSION is not set
-# CONFIG_FUSION_SPI is not set
-# CONFIG_FUSION_FC is not set
-# CONFIG_FUSION_SAS is not set
#
-# IEEE 1394 (FireWire) support
+# Enable only one of the two stacks, unless you know what you are doing
#
# CONFIG_FIREWIRE is not set
# CONFIG_IEEE1394 is not set
# CONFIG_I2O is not set
CONFIG_NETDEVICES=y
-# CONFIG_NETDEVICES_MULTIQUEUE is not set
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
# CONFIG_MACVLAN is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
+# CONFIG_VETH is not set
# CONFIG_ARCNET is not set
# CONFIG_PHYLIB is not set
CONFIG_NET_ETHERNET=y
# CONFIG_DM9102 is not set
# CONFIG_ULI526X is not set
# CONFIG_HP100 is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
# CONFIG_NET_PCI is not set
+# CONFIG_B44 is not set
# CONFIG_NETDEV_1000 is not set
# CONFIG_NETDEV_10000 is not set
# CONFIG_TR is not set
#
# CONFIG_WLAN_PRE80211 is not set
# CONFIG_WLAN_80211 is not set
+# CONFIG_IWLWIFI_LEDS is not set
#
# USB Network Adapters
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
-# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_WAN is not set
# CONFIG_FDDI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
# CONFIG_NET_FC is not set
-# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_NET_POLL_CONTROLLER is not set
#
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_JOYDEV is not set
-# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_EVBUG is not set
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
# CONFIG_SERIAL_NONSTANDARD is not set
+# CONFIG_NOZOMI is not set
#
# Serial drivers
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
# CONFIG_IPMI_HANDLER is not set
-# CONFIG_WATCHDOG is not set
# CONFIG_HW_RANDOM is not set
-# CONFIG_RTC is not set
-CONFIG_COBALT_LCD=y
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_TCG_TPM is not set
CONFIG_DEVPORT=y
# CONFIG_I2C is not set
-
-#
-# SPI support
-#
# CONFIG_SPI is not set
-# CONFIG_SPI_MASTER is not set
# CONFIG_W1 is not set
# CONFIG_POWER_SUPPLY is not set
# CONFIG_HWMON is not set
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+# CONFIG_WATCHDOG is not set
+
+#
+# Sonics Silicon Backplane
+#
+CONFIG_SSB_POSSIBLE=y
+# CONFIG_SSB is not set
#
# Multifunction device drivers
#
+# CONFIG_MFD_CORE is not set
# CONFIG_MFD_SM501 is not set
+# CONFIG_HTC_PASIC3 is not set
#
# Multimedia devices
#
+
+#
+# Multimedia core support
+#
# CONFIG_VIDEO_DEV is not set
# CONFIG_DVB_CORE is not set
+# CONFIG_VIDEO_MEDIA is not set
+
+#
+# Multimedia drivers
+#
# CONFIG_DAB is not set
#
# Graphics support
#
+# CONFIG_DRM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_OUTPUT_CONTROL is not set
+CONFIG_FB=y
+# CONFIG_FIRMWARE_EDID is not set
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_CFB_FILLRECT is not set
+# CONFIG_FB_CFB_COPYAREA is not set
+# CONFIG_FB_CFB_IMAGEBLIT is not set
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+# CONFIG_FB_MODE_HELPERS is not set
+# CONFIG_FB_TILEBLITTING is not set
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_CIRRUS is not set
+# CONFIG_FB_PM2 is not set
+# CONFIG_FB_CYBER2000 is not set
+# CONFIG_FB_ASILIANT is not set
+# CONFIG_FB_IMSTT is not set
+# CONFIG_FB_S1D13XXX is not set
+# CONFIG_FB_NVIDIA is not set
+# CONFIG_FB_RIVA is not set
+# CONFIG_FB_MATROX is not set
+# CONFIG_FB_RADEON is not set
+# CONFIG_FB_ATY128 is not set
+# CONFIG_FB_ATY is not set
+# CONFIG_FB_S3 is not set
+# CONFIG_FB_SAVAGE is not set
+# CONFIG_FB_SIS is not set
+# CONFIG_FB_NEOMAGIC is not set
+# CONFIG_FB_KYRO is not set
+# CONFIG_FB_3DFX is not set
+# CONFIG_FB_VOODOO1 is not set
+# CONFIG_FB_VT8623 is not set
+# CONFIG_FB_TRIDENT is not set
+# CONFIG_FB_ARK is not set
+# CONFIG_FB_PM3 is not set
+# CONFIG_FB_CARMINE is not set
+CONFIG_FB_COBALT=y
+# CONFIG_FB_VIRTUAL is not set
# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Display device support
#
# CONFIG_DISPLAY_SUPPORT is not set
-# CONFIG_VGASTATE is not set
-# CONFIG_VIDEO_OUTPUT_CONTROL is not set
-# CONFIG_FB is not set
#
&n