select BLK_DEV_IDEDMA
help
Enable this to get support for ATA/IDE.
- You can't use paralell ports or SCSI ports
+ You can't use parallel ports or SCSI ports
at the same time.
default "FF"
help
This is a bitmask with information of what bits in PA that a user
- can change change the value on using ioctl's.
+ can change the value on using ioctl's.
Bit set = changeable.
You probably want 00 here.
depends on ETRAX_ARCH_V32
default "0"
help
- SDRAM configuration for group 1. The defult value is 0
+ SDRAM configuration for group 1. The default value is 0
because group 1 is not used in the default configuration,
described in the help for SDRAM_GRP0_CONFIG.
frequency, it may or may not be the same as the external clock
crystal fitted to your board. Some processors have an internal
PLL and can have their frequency programmed at run time, others
- use internal dividers. In gernal the kernel won't setup a PLL
- if it is fitted (there are some expections). This value will be
+ use internal dividers. In general the kernel won't setup a PLL
+ if it is fitted (there are some exceptions). This value will be
specific to the exact CPU that you are using.
config CLOCK_DIV
UML and spend long times with UML stopped at a breakpoint. In this
case, when UML is restarted, it will call the timer enough times to make
up for the time spent at the breakpoint. This could result in a
- noticable lag. If this is a problem, then disable this option.
+ noticeable lag. If this is a problem, then disable this option.
endmenu
help
Enable K8 NUMA node topology detection. You should say Y here if
you have a multi processor AMD K8 system. This uses an old
- method to read the NUMA configurtion directly from the builtin
+ method to read the NUMA configuration directly from the builtin
Northbridge of Opteron. It is recommended to use X86_64_ACPI_NUMA
instead, which also takes priority if both are compiled in.
module will be called analog.
config JOYSTICK_A3D
- tristate "Assasin 3D and MadCatz Panther devices"
+ tristate "Assassin 3D and MadCatz Panther devices"
select GAMEPORT
help
Say Y here if you have an FPGaming or MadCatz controller using the
on files and directories, and database-like indeces on selected
attributes. (Also note that this driver doesn't make those features
available at this time). It is a 64 bit filesystem, so it supports
- extremly large volumes and files.
+ extremely large volumes and files.
If you use this filesystem, you should also say Y to at least one
of the NLS (native language support) options below.
def_bool n
#
-# Architectecture platforms which require a two level mem_section in SPARSEMEM
+# Architecture platforms which require a two level mem_section in SPARSEMEM
# must select this option. This is usually for architecture platforms with
# an extremely sparse physical address space.
#
config IP_FIB_TRIE
bool "FIB_TRIE"
---help---
- Use new experimental LC-trie as FIB lookup algoritm.
+ Use new experimental LC-trie as FIB lookup algorithm.
This improves lookup performance if you have a large
number of routes.
---help---
TCP-Hybla is a sender-side only change that eliminates penalization of
long-RTT, large-bandwidth connections, like when satellite legs are
- involved, expecially when sharing a common bottleneck with normal
+ involved, especially when sharing a common bottleneck with normal
terrestrial connections.
config TCP_CONG_VEGAS
bool "ESP load balancing support"
depends on IP_VS
---help---
- This option enables support for load balancing ESP (Encapsultion
+ This option enables support for load balancing ESP (Encapsulation
Security Payload) transport protocol. Say Y if unsure.
config IP_VS_PROTO_AH
daemon using netlink multicast sockets; unlike the LOG target
which can only be viewed through syslog.
- The apropriate userspace logging daemon (ulogd) may be obtained from
+ The appropriate userspace logging daemon (ulogd) may be obtained from
<http://www.gnumonks.org/projects/ulogd/>
To compile it as a module, choose M here. If unsure, say N.
your distribution will provide these and enable the new controls
in the kernel they also distribute.
- Note that this option can be overriden at boot with the
+ Note that this option can be overridden at boot with the
selinux_compat_net parameter, and after boot via
/selinux/compat_net. See Documentation/kernel-parameters.txt
for details on this parameter.
command line.
config PSS_MIXER
- bool "Enable PSS mixer (Beethoven ADSP-16 and other compatibile)"
+ bool "Enable PSS mixer (Beethoven ADSP-16 and other compatible)"
depends on SOUND_PSS
help
Answer Y for Beethoven ADSP-16. You may try to say Y also for other
git.openpandora.org / pandora-kernel.git / commitdiff