omap3: Runtime detection of Si features

The OMAP35x family has multiple variants differing
in the HW features. This patch detects these features
at runtime and prints information during the boot.

Since most of the code seemed repetitive, macros
have been used for readability.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap1: omap_udc: Add clocking and disable vbus sense for omap7xx

The l3_ocpi_ck clock is needed on omap7xx processors for USB.
Additionally, bit 8 of the SOFT_REQ_REG needs to be enabled for
the usb_dc_ck on omap7xx, which is a different bit than that
of the omap16xx-defined clock of the same name.

I added a provision for the usb_dc_ck and l3_ocpi_ck clocks as
dc_clk and hhc_clk, respectively, for omap7xx CPUs.  Additionally,
I added a check in machine_without_vbus_sense for all omap7xx
devices, as presently I know of no omap7xx-based devices that
have vbus sense, and it made more sense to me to use a cpu check
here than to spell out each machine one at a time.  Finally, DMA
is disabled for omap7xx, as it causes problems with these chips.

Cc: linux-usb@vger.kernel.org
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap1: mmc: Add platform init for omap7xx

The MMC mux pins normally used by omap chips in devices.c
are different from what is needed by omap7xx chips.  This
change adds a conditional around the mux setup code to
enable the correct mux pins.

The omap730 and omap850 both use a different clock for the "fck"
clock of the MMC interface than other omap processors based on the
SOFT_REQ_REG, pin 12.  The "ick" clock is the same as that used
by other omap processors.

* Added the missing clock definition as mmc3_ck to clock.h
* Added the clock definition to omap_clks in clock.c
* Added CK_7XX to the mmci-omap.0 "ick" clock already in clock.c

With these changes, it is now possible to initialize and use MMC
cards with omap730 and omap850 devices.

Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap: introduce OMAP_LL_DEBUG_NONE DEBUG_LL config

Zoom2/Zoom3 kind of boards do not use omap uarts for console.
These use external debug board for console.

So these boards should not have "Uncompressing Kernel...."
log put on omap uarts.

By interoducing OMAP_LL_DEBUG_NONE option,
unnecessary writes to omap uarts is avoided.

In future, the DEBUG_LL interface will be enhanced
to use external debug board.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap: Eliminate OMAP_MAX_NR_PORTS

Eliminate OMAP_MAX_NR_PORTS

Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.

Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.

Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap3: clock: Fixed dpll3_m2x2 rate calculation

Current calculation does not take into account any changes to M2 divisor, and
thus when we change VDD2 OPP, dpll3_m2x2 rate does not change. Fixed by
re-routing dpll3_m2x2 parent to dpll3_m2.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap3: clock: Fix the DPLL freqsel computations

Fix the freqsel value computation. Use n instead of (n+1)

The formula in the TRM uses a zero-based N, hence the (n+1); however
at this point in the clock34xx.c code, N is one-based.

Hayati Bayrakdar <h-bayrakdar@ti.com> and Nishanth Menon <nm@ti.com> helped
track down this bug.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: modified commit message]
Cc: Hayati Bayrakdar <h-bayrakdar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap: Fix keymap for zoom2 according to matrix keypad framwork

Interpretation of 'row' and 'col' got reversed in matrix keymap
framework. Also last element '0', present in keymap array, is no
more needed.
Correcting zoom2 keyboard keymap accordingly.

Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

MFD: twl4030-codec: APLL_INFREQ handling in the MFD driver

Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

OMAP: Configure audio_mclk for twl4030-codec MFD

audio_mclk value is going to be handled by the
twl4030-codec MFD driver, configure the correct
value for boards, which is using the twl4030 audio.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: TWL4030: Add audio_mclk to the codec platform data

Add audio_mclk to the platform data struct for the
twl4030-codec MFD driver.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

OMAP: Platform support for twl4030_codec MFD

Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

MFD: twl4030: add twl4030_codec MFD as a new child to the core

New MFD child to twl4030 MFD device.

Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.

This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.

The platform specific configuration data is passed along to the
child drivers (audio, vibra).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge 7xx-iosplit-plat-merge with omap-fixes

Merge branch '7xx-iosplit-plat-merge' into omap-for-linus

Linux 2.6.32-rc7

Merge branch 'omap-fixes-for-linus' of git://git./linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  omap3: Decrease cpufreq transition latency
  omap3: update Pandora defconfig
  omap3: 3430sdp: Enable Linux Regulator framework
  omap3: beagle: Fix USB host port power control
  omap3: pandora: Fix keypad keymap
  omap1: Amstrad Delta defconfig fixes
  omap: Fix omapfb/lcdc on OMAP1510 broken when PM set
  omap: Use resource_size
  omap: Fix race condition in omap dma driver

__generic_block_fiemap(): fix for files bigger than 4GB

Because of an integer overflow on start_blk, various kind of wrong results
would be returned by the generic_block_fiemap() handler, such as no
extents when there is a 4GB+ hole at the beginning of the file, or wrong
fe_logical when an extent starts after the first 4GB.

Signed-off-by: Mike Hommey <mh@glandium.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Eric Sandeen <sandeen@sgi.com>
Cc: Josef Bacik <jbacik@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pps: events reporting fix up

PPS events must be recorded according to PPS's mode settings.

If a process asks for (i.e.) capture-assert events only, when the PPS
client calls the pps_event() function to save the current PPS event, we
should verify the event type and then discard unwanted ones.

Also, without this patch userland processes waiting for a specific PPS
event (assert or clear but not both) may be awakened at wrong time.

Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: William S. Brasher <billb958@door.net>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pps: locking scheme fix up for PPS_GETPARAMS

Userland programs may read/write PPS parameters at same time and these
operations may corrupt PPS data.

Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

drivers/video/msm: update to new kernel

TASK_INTERRUPTIBLE and friends are now only available after including
<linux/sched.h>, so include it when needed.

bus_id is no longer available/necessary, so remove that.

Android pmem driver is not available in mainline, so remove its hooks
from drivers/video.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

gpiolib: fix device_create() result check

In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails.  Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: v3020: fix v3020_mmio_read_bit()

v3020_mmio_read_bit() always returns 0 when left_shift > 7.

v3020_mmio_read_bit()'s return type is (unsigned char).  The code returns
a value masked by (1 << left_shift) that is casted to the return type.  If
left_shift is larger than 7, the cast will always result in a 0 return
value.  The problem was discovered with left_shift = 16, and the included
patch corrects the problem.

The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.

Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc-vr41xx: fix do_div() warning

drivers/rtc/rtc-vr41xx.c: In function 'vr41xx_rtc_irq_set_freq':
drivers/rtc/rtc-vr41xx.c:217: warning: comparison of distinct pointer types lacks a cast
drivers/rtc/rtc-vr41xx.c:217: warning: right shift count >= width of type
drivers/rtc/rtc-vr41xx.c:217: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'

Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

exec: setup_arg_pages() fails to return errors

In setup_arg_pages we work hard to assign a value to ret, but on exit we
always return 0.

Also remove a now duplicated exit path and branch to out_unlock instead.

Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: put framebuffer drivers back under the "frame buffer devices" menu

The config FB_PRE_INIT_FB entry in drivers/video/Kconfig pushes all entries
below it out of the menuconfig selection. Fix this.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: correct SECURITY SUBSYSTEM git entry

Use git.kernel.org not www.kernel.org

Signed-off-by: Joe Perches <joe@perches.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: correct NETFILTER git entry format

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: correct 9P FILE SYSTEM git entry

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmci-omap: free irq resource

Free IRQ on remove.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: add support for the Lava Quattro PCI quad-port 16550A card

This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

serial: fix printk format specifiers for struct uart_port::iobase

struct uart_port::iobase is unsigned long, so use %lx as printk format
specifier.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: pcf50633: consider alrm->enable in pcf50633_rtc_set_alarm

According to Documentation/rtc.txt, RTC_WKALM_SET sets the alarm time and
enables/disables the alarm.  We implement RTC_WKALM_SET through
pcf50633_rtc_set_alarm.  The enabling/disabling part was missing.

Signed-off-by: Werner Almesberger <werner@openmoko.org>
Reported-by: Michael 'Mickey' Lauer <mickey@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

rtc: pcf50633: fix month off-by-one error

The PCF50633 stores a month value of 1-12, but the kernel wants 0-11.

Signed-off-by: Rask Ingemann Lambertsen <rask@sygehus.dk>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

atmel_lcdfb: new alternate pixel clock formula

at91sam9g45 non ES lots have an alternate pixel clock calculation formula.
Introduce this one with condition on the cpu_is_xxxxx() macros.

Newer 9g45 SOC will not have good pixel clock calculation without this
fix.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs: add missing compat_ptr handling for FS_IOC_RESVSP ioctl

For FS_IOC_RESVSP and FS_IOC_RESVSP64 compat_sys_ioctl() uses its
arg argument as a pointer to userspace. However it is missing a
a call to compat_ptr() which will do a proper pointer conversion.

This was introduced with 3e63cbb1 "fs: Add new pre-allocation ioctls
to vfs for compatibility with legacy xfs ioctls".

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ankit Jain <me@ankitjain.org>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Arnd Bergmann <arndbergmann@googlemail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: <stable@kernel.org> [2.6.31.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

pidns: fix a leak in /proc dentries and inodes with pid namespaces.

Daniel Lezcano reported a leak in 'struct pid' and 'struct pid_namespace'
that is discussed in:

http://lkml.org/lkml/2009/10/2/159.

To summarize the thread, when container-init is terminated, it sets the
PF_EXITING flag, zaps other processes in the container and waits to reap
them.  As a part of reaping, the container-init should flush any /proc
dentries associated with the processes.  But because the container-init is
itself exiting and the following PF_EXITING check, the dentries are not
flushed, resulting in leak in /proc inodes and dentries.

This fix reverts the commit 7766755a2f249e7e0 ("Fix /proc dcache deadlock
in do_exit") which introduced the check for PF_EXITING.  At the time of
the commit, shrink_dcache_parent() flushed dentries from other filesystems
also and could have caused a deadlock which the commit fixed.  But as
pointed out by Eric Biederman, after commit 0feae5c47aabdde59,
shrink_dcache_parent() no longer affects other filesystems.  So reverting
the commit is now safe.

As pointed out by Jan Kara, the leak is not as critical since the
unclaimed space will be reclaimed under memory pressure or by:

echo 3 > /proc/sys/vm/drop_caches

But since this check is no longer required, its best to remove it.

Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Reported-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Jan Kara <jack@ucw.cz>
Cc: Andrea Arcangeli <andrea@cpushare.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: move THREAD_SIZE definition outside #ifndef ASSEMBLY

arch/alpha/kernel/vmlinux.lds.S uses it:

arch/alpha/kernel/vmlinux.lds:241: undefined symbol `THREAD_SIZE' referenced in expression

Seems to have been caused by

commit 9d93f00580243cc059510d9d6ac4d2f5e97e5b83
Author:     Geoffrey Thomas <geofft@ksplice.com>
AuthorDate: Thu Sep 24 10:36:26 2009 -0400
Commit:     Linus Torvalds <torvalds@linux-foundation.org>
CommitDate: Thu Sep 24 17:16:22 2009 -0700

    alpha: Clean up linker script using new linker script macros.

    Note that .data.page_aligned and .data.cacheline_aligned are now after
    _data; it was probably a bug that they were before it.

    Also, some explicit ALIGN(8)'s between various initcall sections were
    removed; this should be harmless as the implicit alignment of
    initcall_t was already 8.

Cc: Geoffrey Thomas <geofft@ksplice.com>
Cc: Tim Abbott <tabbott@ksplice.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

alpha: fix F_SETOWN_EX and F_GETLK64 conflict

Fix a bug in

    commit ba0a6c9f6fceed11c6a99e8326f0477fe383e6b5
    Author:     Peter Zijlstra <a.p.zijlstra@chello.nl>
    AuthorDate: Wed Sep 23 15:57:03 2009 -0700
    Commit:     Linus Torvalds <torvalds@linux-foundation.org>
    CommitDate: Thu Sep 24 07:21:01 2009 -0700

        fcntl: add F_[SG]ETOWN_EX

In asm-generic/fcntl.h, F_SETOWN_EX and F_GETLK64 both have value 12, and
F_GETOWN_EX and F_SETLK64 both have value 13.

Reported-by: "Joseph S. Myers" <joseph@codesourcery.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Andreas Schwab <schwab@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memcg: fix wrong pointer initialization at page migration when memcg is disabled.

Lee Schermerhorn reported that he saw bad pointer dereference in
mem_cgroup_end_migration() when he disabled memcg by boot option.

memcg's page migration logic works as

mem_cgroup_prepare_migration(page, &ptr);
do page migration
mem_cgroup_end_migration(page, ptr);

Now, ptr is not initialized in prepare_migration when memcg is disabled
by boot option. This causes panic in end_migration. This patch fixes it.

Reported-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

savagefb: fix blanking mode on CRT display

Fix wrong bit mask for blanking register.  Due to the error a CRT monitor
blanks off due to wrong frequency (out of range) instead of PM signal
(vertical and horizontal frequencies cut off).

Just compare the mask with bits set in the switch(blank) clause below the
changed line.

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fb: remove fb_save_state() and fb_restore_state operations

Remove fb_save_state() and fb_restore_state operations from frame buffer layer.
They are used only in two drivers:
1. savagefb  - and cause bug #11248
2. uvesafb

Usage of these operations is misunderstood in both drivers so kill these
operations, fix the bug #11248 and avoid confusion in the future.

Tested on Savage 3D/MV card and the patch fixes the bug #11248.

The frame buffer layer uses these funtions during switch between graphics
and text mode of the console, but these drivers saves state before
switching of the frame buffer (in the fb_open) and after releasing it (in
the fb_release).  This defeats the purpose of these operations.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11248

Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Jochen Hein <jochen@jochen.org>
Tested-by: Jochen Hein <jochen@jochen.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

page allocator: Do not allow interrupts to use ALLOC_HARDER

Commit 341ce06f69abfafa31b9468410a13dbd60e2b237 ("page allocator:
calculate the alloc_flags for allocation only once") altered watermark
logic slightly by allowing rt_tasks that are handling an interrupt to set
ALLOC_HARDER.  This patch brings the watermark logic more in line with
2.6.30.

This change results in a reduction of the number high-order GFP_ATOMIC
allocation failures reported.  See
http://www.gossamer-threads.com/lists/linux/kernel/1144153

[rientjes@google.com: Spotted the problem]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

page allocator: always wake kswapd when restarting an allocation attempt after direct reclaim failed

If a direct reclaim makes no forward progress, it considers whether it
should go OOM or not.  Whether OOM is triggered or not, it may retry the
allocation afterwards.  In times past, this would always wake kswapd as
well but currently, kswapd is not woken up after direct reclaim fails.
For order-0 allocations, this makes little difference but if there is a
heavy mix of higher-order allocations that direct reclaim is failing for,
it might mean that kswapd is not rewoken for higher orders as much as it
did previously.

This patch wakes up kswapd when an allocation is being retried after a
direct reclaim failure.  It would be expected that kswapd is already
awake, but this has the effect of telling kswapd to reclaim at the higher
order as well.

Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: openipmi list is moderated

openipmi list is moderated.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

get_maintainer: fix usage comment

With the `s' it just won't work.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: VMWARE VMXNET3 - Quote name with comma and period, use tabs

Names with periods or commas need to be quoted
Use tab not spaces

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: SERVER ENGINES 10Gbps iSCSI - Use single line M:

Integrate P:/M: lines to single M:
Use tabs not spaces

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: BROCADE BFA - Use single line M: and tabs

Integrate P:/M: to single M:
Use tab for spacing

Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jing Huang <huangj@brocade.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

MAINTAINERS: ASUS ACPI EXTRAS - remove F:arch/x86/kernel/acpi/boot.c

Oops.  How did that get there?
(Don't look, it's my original pattern commit...)

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fs/jbd: Export log_start_commit to fix ext3 build.

This fixes:
ERROR: "log_start_commit" [fs/ext3/ext3.ko] undefined!

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

Merge branch 'pm-upstream/pm-cpuidle' of ssh:///linux/kernel/git/khilman/linux-omap-pm into 7xx-iosplit-plat-merge

Merge branch 'pm-upstream/pm-off' of ssh:///linux/kernel/git/khilman/linux-omap-pm into 7xx-iosplit-plat-merge

omap3: Decrease cpufreq transition latency

Adjust OMAP3 frequency transition latency from 10,000,000uS to a more
reasonable 300,000uS.  This causes ondemand and conservative governors to
sample CPU load more often resulting in more responsive behavior.

Tested on Android 2.6.29; using this value and conservative governor, CORE
power consumption on Zoom2 was comparable to the old and unresponsive
10,000,000uS value while UI responsiveness was greatly improved.

Signed-off-by: Mike Turquette <mturquette@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP3: PM: Added resched check into idle calls

Fixes a bug where scheduling is delayed until next wakeup due to race
condition (e.g. interrupt requests scheduling just before omap_sram_idle
is entered.)

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: idle: Remove fclk check for idle loop

This patch removes the check to see if some functional clocks are
still enabled before entering sleep.  This is no longer needed when
using safe state (C1) that keeps CORE active.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Use pwrdm_set_next_pwrst instead of set_pwrdm_state in idle loop

It is more efficient to use pwrdm_set_next_pwrst for mpu, core and neon
instead of set_pwrdm_state in idle loop. It is anyway known that those are
active in idle loop. So no need to use set_pwrdm_state.

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: Start C-state definitions from base 0

The current definition of C-states starts from base 1.
Whereas, the cpuidle driver uses base 0. This patch
eliminates need for explicit mapping (add/ sbutract)
due to different base values.

Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: Add new lower-latency C1 state

This patch introduces a new C state which allows MPU to go to WFI but keeps
the core domain active. This offers a much better wakeup latency (3us vs
10s of us for the current C1) at the cost of a higher power consumption.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: fix init sequencing

Previously omap3_idle_init() was called in device_init, while
omap_pm_init() is called at late_initcall. This causes the cpu idle
driver to call omap_sram_idle before it is properly initialized. This
patch fixes the issue by moving omap3_idle_init into omap3_pm_init.

Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: check activity for C2, C3, correct accounting

Use the activity check for states C2 and C3 as well.  This is
primarily to prevent deeper states during UART activity.

Also, if a different state is chosen than the target state, update the
'last_state' accordingly so that CPUidle state accounting is coorect.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: obey enable_off_mode flag

If 'enable_off_mode' is not set, force powerdomain states to RET
instead of OFF.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: support retention and off-mode C-states

This patch adds support and enables state C4(MPU RET + CORE RET)
and MPU OFF states (C3 and C5.)

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CPUidle: base driver and support for C1-C2

Basic CPUidle driver for OMAP3 with deepest sleep state supported
being MPU CSWR.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Program SDRC to send self refresh on timeout of AUTO_CNT

Due to an OMAP3 errata (1.142), on HS/EMU devices SDRC should be
programed to issue automatic self refresh on timeout
of AUTO_CNT = 1 prior to any transition to OFF mode.
This is needed only on sil rev's ES3.0 and above.

This patch enables the above needed WA in the SDRC power register
value stored in scratchpad, so that ROM code restores this value
in SDRC POWER on the wakeup path.
The original SDRC POWER register value is stored and restored back
in omap_sram_idle() function.

This fixes some random crashes observed while stressing suspend
on HS/EMU devices.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Enable IO-CHAIN wakeup

OMAP 3430 ES3.1 chips have a separate bit for IO daisy-chain
wake up enabling. It needs to be enabled when entering
retention or off state, otherwise waking up might not work
in all situations.

Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: MPU and CORE should stay awake if there is CAM domain ACTIVE

MPU and CORE should stay awake if there is CAM domain ACTIVE. This is
because that module doesn't have wake-up capability.

This should replace the patch that is currently in the PM branch.

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Prevent PER from going OFF when CORE is going INA

OMAP3 can't generate wakeups in this state, thus it is not permitted.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: decouple PER and CORE context save and restore

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

PM debug: allow configurable wakeup from suspend on OMAP GPtimer

Using debugfs, export a configurable wakeup timer to be used to
wakeup system from suspend.

If a non-zero value is written to
/debug/pm_debug/wakeup_timer_seconds, A timer wakeup event will wake
the system and resume after the configured number of seconds.

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM debug: allow runtime toggle of PM features

Allow enable/disable of low-power states during idle.  To
enable low-power idle:

   echo 1 > /debug/pm_debug/sleep_while_idle

 to disable:

   echo 0 > /debug/pm_debug/sleep_while_idle

Also allow enable/disable of OFF-mode.  To enable:

   echo 1 > /debug/pm_debug/enable_off_mode

 to disable:

   echo 0 > /debug/pm_debug/enable_off_mode

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Wait for SDRC ready iso a blind delay

This patch improves the wakeup SRAM code polling the SDRC to become ready
instead of just waiting for a fixed amount of time.

Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

PM: Disable usb host HW save and restore

The hardware SAVEANDRESTORE mechanism seems to leave
USB HOST power domain permanently into active state
after one transition from off to active state.
Disabling for now.

Signed-off-by: Kalle Jokiniemi <ext-kalle.jokiniemi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Fix INTC context save/restore

Wrong index was used for ILR.

Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: SDRC auto-refresh workaround for off-mode

Errata: ES3.0, ES3.1 SDRC not sending auto-refresh when OMAP wakes-up
from OFF mode

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP: Store reboot mode in scratchpad on OMAP34xx

The reboot mode can be communicated to a bootloader (or the
kernel itself) with a scratchpad register. This functionality
is especially useful, if userspace is allowed to change
the reboot mode.

Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP: PM: Clear DMA channel state after a wakeup

Clear DMA channel states so that users can assume a known initial
state.

Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Fix PLL_MOD CLKEN offset in scratchpad

The CM_CLKEN_PLL register saved in scratchpad memory
was wrongly using offset of 0x0004 instead of 0x0000.

The effect of this was that boot ROM code would
restore the wrong value when waking up from off mode.
This wrong value, however, will be overwritten by
prcm context restore. Still, a short period of wrong
clock settings in CM_CLKEN_PLL remained between ROM
code and prcm context restore. This is fixed by the
patch.

Problem reported by: Jouni Hogander <jouni.hogander@nokia.com>

Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

ARM: OMAP: SMS: save/restore of SMS_SYSCONFIG for off-mode

The SMS_SYSCONFIG register gets reset in off mode, added a
save/restore mechanism for that.

Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Fix secure SRAM context save/restore

The secure sram context save uses dma channels 0 and 1.
In order to avoid collision between kernel DMA transfers and
ROM code dma transfers, we need to reserve DMA channels 0
1 on high security devices.

A bug in ROM code leaves dma irq status bits uncleared.
Hence those irq status bits need to be cleared when restoring
DMA context after off mode.

There was also a faulty parameter given to PPA in the secure
ram context save assembly code, which caused interrupts to
be enabled during secure ram context save. This caused the
save to fail sometimes, which resulted the saved context
to be corrupted, but also left DMA channels in secure mode.
The secure mode DMA channels caused "DMA secure error with
device 0" errors to be displayed.

Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Save and restore also CM_CLKSEL1_PLL_IVA2

CM_CLKSEL1_PLL_IVA2 is not saved/restored currently. This patch is
adding save and restore for it.

Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Enable SDRAM auto-refresh during sleep

Fix for ES3.0 bug: SDRC not sending auto-refresh when OMAP wakes-up
from OFF mode (warning for HS devices.)

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: save secure RAM only during init

The function omap3_save_secure_ram() is now called only once during
the initialization of the device and consequent sleep cycles will
re-use the same saved contents for secure RAM. Users who need secure
services should do secure RAM saving before entering off-mode, if a
secure service has been accessed after last save.

There are both latency and reliability issues with saving secure RAM
context in the idle path. The context save uses a hardware resource
which takes an order of hundreds of milliseconds to initialize after a
wake up from off-mode, and also there is no way of checking whether it
is ready from kernel side or not. It just crashes if you use it too
quickly

Additional fix to ensure scratchpad save is done after secure
RAM by Roger Quadros.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3 PM: off-mode support for HS/EMU devices

For HS/EMU devices, some additional resources need to be
saved/restored for off-mode support.  Namely, saving the secure RAM
and a pointer to it in the scratchpad.

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP: PM: DMA context save/restore for off-mode support

For HS/EMU devices, these additional features are also used:

- DMA interrupt disable routine added
- Added DMA controller reset to DMA context restore

Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: CORE domain off-mode support

Add context save and restore for CORE powerdomain resources in order
to support off-mode.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: MPU off-mode support

Adds a 'save_state' option when calling into SRAM idle function
and adds some minor cleanups of SRAM asm code.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Restore MMU table entry

During the MMU restoration on the restore path from MPU OFF, the page
table entry for the page consisting of the code being executed is
modified to make MMU return VA=PA.

The MMU is then enabled and the original entry is being stored in
scratchpad.  This patch reads the original values stored in
scratchpad, and restores them back.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: handle PER/NEON/CORE in idle

Expand the powerdomains handled in the idle path to include PER, NEON
and CORE.  This includes properly clearing the previous powerstates,
linking NEON state to MPU state and calling the UART prepare functions
for only the appropraite powerdomain transitions (CORE for UART1,2,
PER for UART3.)

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: restore SRAM functions after off-mode.

Generalize the copy of SRAM functions into omap_push_sram_idle()
so it can be used on init but also after off-mode transitions.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: SCM context save/restore

Add context save and restore for the System Control Module to suport
off-mode.

ETK and debobs definitions added by Peter De Schrijver.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: Populate scratchpad contents

This patch populates the scratchpad contents as expected by the
bootROM code.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: PRCM context save/restore

Add context save and restore for PRCM module to support off-mode.
Additional registers (CM_CLKSEL4, CM_CLKEN, CM_CLKEN2) added by Tero
Kristo.

Missing CM_CLKEN_PLL_IVA2 register added by Kalle Jokiniemi.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: INTC context save/restore

Add context save and restore for the INTC module to support off-mode.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: GPIO context save/restore

Add context save and restore to enable off-mode.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

OMAP3: PM: GPMC context save/restore

This patch adds the context save and restore functions for GPMC to
enable off-mode.

Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>

Merge git://git./linux/kernel/git/mason/btrfs-unstable

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: fix panic when trying to destroy a newly allocated
  Btrfs: allow more metadata chunk preallocation
  Btrfs: fallback on uncompressed io if compressed io fails
  Btrfs: find ideal block group for caching
  Btrfs: avoid null deref in unpin_extent_cache()
  Btrfs: skip btrfs_release_path in btrfs_update_root and btrfs_del_root
  Btrfs: fix some metadata enospc issues
  Btrfs: fix how we set max_size for free space clusters
  Btrfs: cleanup transaction starting and fix journal_info usage
  Btrfs: fix data allocation hint start

btusb bluetooth driver: wait for 'waker' work too before closing

Rafael debugged a resume-time hang (with oopses in workqueue handling)
on his laptop that was due to the 'waker' workqueue entry being
disconnected and then released without the workqueue entry having been
synchronized.

Several people were involved, with Oleg Nesterov doing a debugging patch
showing what workqueue entry was corrupt etc.

This was a regression introduced by commit 7bee549e19 ("Bluetooth: Add
USB autosuspend support to btusb driver") as Rafael points out (not
actually bisected, but it became clear once the bug was found).

Tested-and-reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Btrfs: fix panic when trying to destroy a newly allocated

There is a problem where iget5_locked will look for an inode, not find it, and
then subsequently try to allocate it.  Another CPU will have raced in and
allocated the inode instead, so when iget5_locked gets the inode spin lock again
and does a search, it finds the new inode.  So it goes ahead and calls
destroy_inode on the inode it just allocated.  The problem is we don't set
BTRFS_I(inode)->root until the new inode is completely initialized.  This patch
makes us set root to NULL when alloc'ing a new inode, so when we get to
btrfs_destroy_inode and we see that root is NULL we can just free up the memory
and continue on.  This fixes the panic

http://www.kerneloops.org/submitresult.php?number=812690

Thanks,

Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>

Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs-2.6

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  JBD/JBD2: free j_wbuf if journal init fails.
  ext3: Wait for proper transaction commit on fsync
  ext3: retry failed direct IO allocations

Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - possible read past array alc88[02]_parse_auto_config()
  sound: rawmidi: fix MIDI device O_APPEND error handling
  sound: rawmidi: fix checking of O_APPEND when opening MIDI device
  sound: rawmidi: fix double init when opening MIDI device with O_APPEND
  ALSA: hda - Avoid quirk for HP dc5750
  ALSA: hda - Tweak OLPC XO-1.5 microphone bias
  ALSA: hda: Use model=auto quirk for Sony VAIO VGN-FW170J using ALC262