uart6850= [HW,OSS]
Format: <io>,<irq>
+ uhci-hcd.ignore_oc=
+ [USB] Ignore overcurrent events (default N).
+ Some badly-designed motherboards generate lots of
+ bogus events, for ports that aren't wired to
+ anything. Set this parameter to avoid log spamming.
+ Note that genuine overcurrent events won't be
+ reported either.
+
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
Required properties:
- device_type : has to be "rom"
- - compatible : Should specify what this ROM device is compatible with
- (i.e. "onenand"). Currently, this is most likely to be "direct-mapped"
- (which corresponds to the MTD physmap mapping driver).
- - regs : Offset and length of the register set (or memory mapping) for
+ - compatible : Should specify what this flash device is compatible with.
+ Currently, this is most likely to be "direct-mapped" (which
+ corresponds to the MTD physmap mapping driver).
+ - reg : Offset and length of the register set (or memory mapping) for
the device.
+ - bank-width : Width of the flash data bus in bytes. Required
+ for the NOR flashes (compatible == "direct-mapped" and others) ONLY.
Recommended properties :
- - bank-width : Width of the flash data bus in bytes. Required
- for the NOR flashes (compatible == "direct-mapped" and others) ONLY.
- partitions : Several pairs of 32-bit values where the first value is
partition's offset from the start of the device and the second one is
partition size in bytes with LSB used to signify a read only
- partititon (so, the parition size should always be an even number).
+ partition (so, the parition size should always be an even number).
- partition-names : The list of concatenated zero terminated strings
representing the partition names.
+ - probe-type : The type of probe which should be done for the chip
+ (JEDEC vs CFI actually). Valid ONLY for NOR flashes.
Example:
flash@ff000000 {
device_type = "rom";
compatible = "direct-mapped";
- regs = <ff000000 01000000>;
+ probe-type = "CFI";
+ reg = <ff000000 01000000>;
bank-width = <4>;
partitions = <00000000 00f80000
00f80000 00080001>;
<informalexample>
<programlisting>
<![CDATA[
- struct mychip *chip = (struct mychip *)card->private_data;
+ struct mychip *chip = card->private_data;
]]>
</programlisting>
</informalexample>
/* release the irq */
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
/* release the i/o ports & memory */
pci_release_regions(chip->pci);
/* disable the PCI entry */
}
chip->port = pci_resource_start(pci, 0);
if (request_irq(pci->irq, snd_mychip_interrupt,
- IRQF_DISABLED|IRQF_SHARED, "My Chip", chip)) {
+ IRQF_SHARED, "My Chip", chip)) {
printk(KERN_ERR "cannot grab irq %d\n", pci->irq);
snd_mychip_free(chip);
return -EBUSY;
<programlisting>
<![CDATA[
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
]]>
</programlisting>
</informalexample>
P: David Brownell
M: dbrownell@users.sourceforge.net
L: linux-usb-devel@lists.sourceforge.net
-S: Maintained
+S: Odd Fixes
USB ET61X[12]51 DRIVER
P: Luca Risolia
W: http://www.one-eyed-alien.net/~mdharm/linux-usb/
USB OHCI DRIVER
-P: Roman Weissgaerber
-M: weissg@vienna.at
+P: David Brownell
+M: dbrownell@users.sourceforge.net
L: linux-usb-users@lists.sourceforge.net
L: linux-usb-devel@lists.sourceforge.net
-S: Maintained
+S: Odd Fixes
USB OPTION-CARD DRIVER
P: Matthias Urlichs
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc1-git9
-# Sat Jul 15 15:08:10 2006
+# Linux kernel version: 2.6.20-rc1
+# Sat Dec 16 06:05:24 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
# CONFIG_TASKSTATS is not set
-CONFIG_SYSCTL=y
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP23XX is not set
#
CONFIG_MACH_ADSSPHERE=y
CONFIG_MACH_EDB9302=y
+CONFIG_MACH_EDB9302A=y
CONFIG_MACH_EDB9312=y
CONFIG_MACH_EDB9315=y
CONFIG_MACH_EDB9315A=y
#
CONFIG_CPU_32=y
CONFIG_CPU_ARM920T=y
-CONFIG_CPU_32v4=y
+CONFIG_CPU_32v4T=y
CONFIG_CPU_ABRT_EV4T=y
CONFIG_CPU_CACHE_V4WT=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
#
# Processor Features
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
CONFIG_NET_KEY=y
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=-1
# CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED is not set
# CONFIG_MTD_REDBOOT_PARTS_READONLY is not set
-# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
# CONFIG_MTD_AFS_PARTS is not set
#
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
#
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_UB is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
# CONFIG_SCSI_PROC_FS is not set
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
#
-# SCSI Transport Attributes
+# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
#
# CONFIG_ISCSI_TCP is not set
-# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_DEBUG is not set
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
+
#
# Multi-device support (RAID and LVM)
#
#
CONFIG_NET_ETHERNET=y
CONFIG_MII=y
+CONFIG_EP93XX_ETH=y
# CONFIG_SMC91X is not set
# CONFIG_DM9000 is not set
# CONFIG_NVRAM is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# CONFIG_SENSORS_DS1337 is not set
# CONFIG_SENSORS_DS1374 is not set
-# CONFIG_SENSORS_EEPROM is not set
+CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Misc devices
#
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
CONFIG_USB_DYNAMIC_MINORS=y
+# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
#
# USB Input Devices
#
-# CONFIG_USB_HID is not set
#
# USB HID Boot Protocol drivers
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
CONFIG_USB_RTL8150=y
+# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_MON is not set
CONFIG_USB_SERIAL=y
CONFIG_USB_SERIAL_CONSOLE=y
# CONFIG_USB_SERIAL_GENERIC is not set
+# CONFIG_USB_SERIAL_AIRCABLE is not set
# CONFIG_USB_SERIAL_AIRPRIME is not set
-# CONFIG_USB_SERIAL_ANYDATA is not set
# CONFIG_USB_SERIAL_ARK3116 is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_KOBIL_SCT is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
+# CONFIG_USB_SERIAL_MOS7720 is not set
+# CONFIG_USB_SERIAL_MOS7840 is not set
# CONFIG_USB_SERIAL_NAVMAN is not set
CONFIG_USB_SERIAL_PL2303=y
# CONFIG_USB_SERIAL_HP4X is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OPTION is not set
# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_DEBUG is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGETKIT is not set
-# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_TEST is not set
#
CONFIG_RTC_CLASS=y
CONFIG_RTC_HCTOSYS=y
CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
#
# RTC interfaces
# RTC drivers
#
# CONFIG_RTC_DRV_X1205 is not set
-# CONFIG_RTC_DRV_DS1307 is not set
+CONFIG_RTC_DRV_DS1307=y
# CONFIG_RTC_DRV_DS1553 is not set
# CONFIG_RTC_DRV_ISL1208 is not set
# CONFIG_RTC_DRV_DS1672 is not set
# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# CONFIG_CRYPTO is not set
-#
-# Hardware crypto devices
-#
-
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.19
-# Fri Dec 1 10:51:01 2006
+# Linux kernel version: 2.6.20-rc1-git5
+# Tue Dec 19 21:38:01 2006
#
CONFIG_ARM=y
# CONFIG_GENERIC_TIME is not set
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
# CONFIG_AUDIT is not set
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
# Block layer
#
CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
CONFIG_ARM_THUMB=y
# CONFIG_CPU_DCACHE_DISABLE is not set
# CONFIG_CPU_BPREDICT_DISABLE is not set
+# CONFIG_IWMMXT is not set
#
# Bus support
#
CONFIG_PCI=y
+# CONFIG_PCI_MULTITHREAD_PROBE is not set
#
# PCCARD (PCMCIA/CardBus) support
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
-# CONFIG_IPV6 is not set
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=2
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
#
# SCSI Transports
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=y
+
#
# USB support
#
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
+CONFIG_ECRYPT_FS=y
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DEBUG_BUGVERBOSE=y
-# CONFIG_DEBUG_FS is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_USER=y
#
# Security options
#
-# CONFIG_KEYS is not set
+CONFIG_KEYS=y
+CONFIG_KEYS_DEBUG_PROC_KEYS=y
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
-# CONFIG_CRYPTO is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=y
+CONFIG_CRYPTO_NULL=y
+CONFIG_CRYPTO_MD4=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_WP512=y
+CONFIG_CRYPTO_TGR192=y
+CONFIG_CRYPTO_GF128MUL=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_LRW=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_BLOWFISH=y
+CONFIG_CRYPTO_TWOFISH=y
+CONFIG_CRYPTO_TWOFISH_COMMON=y
+CONFIG_CRYPTO_SERPENT=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_CAST5=y
+CONFIG_CRYPTO_CAST6=y
+CONFIG_CRYPTO_TEA=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_KHAZAD=y
+CONFIG_CRYPTO_ANUBIS=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_TEST is not set
+
+#
+# Hardware crypto devices
+#
#
# Library routines
#
+CONFIG_BITREVERSE=y
CONFIG_CRC_CCITT=y
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc7
-# Tue Sep 19 00:30:18 2006
+# Linux kernel version: 2.6.20-rc1-git5
+# Tue Dec 19 21:37:52 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-CONFIG_SYSCTL=y
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_IMX is not set
CONFIG_ARCH_IOP32X=y
# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP23XX is not set
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
#
# Processor Features
#
# CONFIG_ARM_THUMB is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_IWMMXT is not set
CONFIG_XSCALE_PMU=y
#
# Bus support
#
CONFIG_PCI=y
+# CONFIG_PCI_MULTITHREAD_PROBE is not set
# CONFIG_PCI_DEBUG is not set
#
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
-# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_LOOP=y
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
#
-# SCSI Transport Attributes
+# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
-# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+CONFIG_ATA=y
+# CONFIG_SATA_AHCI is not set
+# CONFIG_SATA_SVW is not set
+# CONFIG_ATA_PIIX is not set
+# CONFIG_SATA_MV is not set
+# CONFIG_SATA_NV is not set
+# CONFIG_PDC_ADMA is not set
+# CONFIG_SATA_QSTOR is not set
+# CONFIG_SATA_PROMISE is not set
+# CONFIG_SATA_SX4 is not set
+CONFIG_SATA_SIL=y
+# CONFIG_SATA_SIL24 is not set
+# CONFIG_SATA_SIS is not set
+# CONFIG_SATA_ULI is not set
+# CONFIG_SATA_VIA is not set
+# CONFIG_SATA_VITESSE is not set
+# CONFIG_PATA_ALI is not set
+# CONFIG_PATA_AMD is not set
+# CONFIG_PATA_ARTOP is not set
+# CONFIG_PATA_ATIIXP is not set
+# CONFIG_PATA_CMD64X is not set
+# CONFIG_PATA_CS5520 is not set
+# CONFIG_PATA_CS5530 is not set
+# CONFIG_PATA_CYPRESS is not set
+# CONFIG_PATA_EFAR is not set
+# CONFIG_ATA_GENERIC is not set
+# CONFIG_PATA_HPT366 is not set
+# CONFIG_PATA_HPT37X is not set
+# CONFIG_PATA_HPT3X2N is not set
+# CONFIG_PATA_HPT3X3 is not set
+# CONFIG_PATA_IT821X is not set
+# CONFIG_PATA_JMICRON is not set
+# CONFIG_PATA_TRIFLEX is not set
+# CONFIG_PATA_MARVELL is not set
+# CONFIG_PATA_MPIIX is not set
+# CONFIG_PATA_OLDPIIX is not set
+# CONFIG_PATA_NETCELL is not set
+# CONFIG_PATA_NS87410 is not set
+# CONFIG_PATA_OPTI is not set
+# CONFIG_PATA_OPTIDMA is not set
+# CONFIG_PATA_PDC_OLD is not set
+# CONFIG_PATA_RADISYS is not set
+# CONFIG_PATA_RZ1000 is not set
+# CONFIG_PATA_SC1200 is not set
+# CONFIG_PATA_SERVERWORKS is not set
+# CONFIG_PATA_PDC2027X is not set
+# CONFIG_PATA_SIL680 is not set
+# CONFIG_PATA_SIS is not set
+# CONFIG_PATA_VIA is not set
+# CONFIG_PATA_WINBOND is not set
#
# Multi-device support (RAID and LVM)
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=y
+# CONFIG_DM_DEBUG is not set
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_MIRROR is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
#
# Ethernet (10000 Mbit)
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Misc devices
#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
+# CONFIG_USB_DABUSB is not set
#
# Graphics support
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=y
+
#
# USB support
#
# CONFIG_USB_DEVICEFS is not set
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
#
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LED is not set
# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGETKIT is not set
-# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
#
# USB DSL modem support
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_ADFS_FS is not set
# CONFIG_AFFS_FS is not set
+CONFIG_ECRYPT_FS=y
# CONFIG_HFS_FS is not set
# CONFIG_HFSPLUS_FS is not set
# CONFIG_BEFS_FS is not set
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V3_ACL is not set
# CONFIG_NFSD_V4 is not set
-# CONFIG_NFSD_TCP is not set
+CONFIG_NFSD_TCP=y
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
#
# CONFIG_NLS is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# Security options
#
-# CONFIG_KEYS is not set
+CONFIG_KEYS=y
+CONFIG_KEYS_DEBUG_PROC_KEYS=y
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
-# CONFIG_CRYPTO is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=y
+CONFIG_CRYPTO_NULL=y
+CONFIG_CRYPTO_MD4=y
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA256=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_WP512=y
+CONFIG_CRYPTO_TGR192=y
+CONFIG_CRYPTO_GF128MUL=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_LRW=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_BLOWFISH=y
+CONFIG_CRYPTO_TWOFISH=y
+CONFIG_CRYPTO_TWOFISH_COMMON=y
+CONFIG_CRYPTO_SERPENT=y
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_CAST5=y
+CONFIG_CRYPTO_CAST6=y
+CONFIG_CRYPTO_TEA=y
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_KHAZAD=y
+CONFIG_CRYPTO_ANUBIS=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_CRC32C=y
+# CONFIG_CRYPTO_TEST is not set
#
# Hardware crypto devices
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
-# CONFIG_LIBCRC32C is not set
+CONFIG_LIBCRC32C=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc7
-# Tue Sep 19 00:30:42 2006
+# Linux kernel version: 2.6.20-rc1
+# Sat Dec 16 06:05:34 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
# CONFIG_TASKSTATS is not set
-CONFIG_SYSCTL=y
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
CONFIG_KALLSYMS_ALL=y
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_IOP32X is not set
CONFIG_ARCH_IOP33X=y
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP23XX is not set
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
#
# Processor Features
#
# CONFIG_ARM_THUMB is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_IWMMXT is not set
CONFIG_XSCALE_PMU=y
#
# Bus support
#
CONFIG_PCI=y
+# CONFIG_PCI_MULTITHREAD_PROBE is not set
# CONFIG_PCI_DEBUG is not set
#
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
# CONFIG_BLK_DEV_UMEM is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
#
-# SCSI Transport Attributes
+# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
-# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
-# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
# CONFIG_MD_MULTIPATH is not set
# CONFIG_MD_FAULTY is not set
CONFIG_BLK_DEV_DM=y
+# CONFIG_DM_DEBUG is not set
# CONFIG_DM_CRYPT is not set
# CONFIG_DM_SNAPSHOT is not set
# CONFIG_DM_MIRROR is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
#
# Ethernet (10000 Mbit)
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Misc devices
#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=y
+
#
# USB support
#
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
CONFIG_XFS_SECURITY=y
CONFIG_XFS_POSIX_ACL=y
# CONFIG_XFS_RT is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
#
# CONFIG_NLS is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# CONFIG_CRYPTO is not set
-#
-# Hardware crypto devices
-#
-
#
# Library routines
#
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc1
-# Sun Jul 9 15:28:50 2006
+# Linux kernel version: 2.6.20-rc1
+# Sat Dec 16 06:05:39 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
-CONFIG_SYSCTL=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
CONFIG_ARCH_IXP2000=y
# CONFIG_ARCH_IXP23XX is not set
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
#
# Processor Features
#
# CONFIG_ARM_THUMB is not set
CONFIG_CPU_BIG_ENDIAN=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_IWMMXT is not set
CONFIG_XSCALE_PMU=y
#
# Bus support
#
CONFIG_PCI=y
+# CONFIG_PCI_MULTITHREAD_PROBE is not set
# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
#
-# CONFIG_PCCARD is not set
#
# Kernel Features
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
#
CONFIG_STANDALONE=y
# CONFIG_PREVENT_FIRMWARE_BUILD is not set
-# CONFIG_FW_LOADER is not set
# CONFIG_DEBUG_DRIVER is not set
# CONFIG_SYS_HYPERVISOR is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
# CONFIG_FORCEDETH is not set
CONFIG_CS89x0=y
# CONFIG_DGRS is not set
-CONFIG_EEPRO100=y
-# CONFIG_E100 is not set
+# CONFIG_EEPRO100 is not set
+CONFIG_E100=y
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
#
# Ethernet (10000 Mbit)
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
# Wan interfaces
#
CONFIG_WAN=y
-# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
CONFIG_HDLC=y
CONFIG_HDLC_RAW=y
# CONFIG_WANXL is not set
# CONFIG_PC300 is not set
# CONFIG_FARSYNC is not set
+# CONFIG_DSCC4 is not set
CONFIG_DLCI=y
CONFIG_DLCI_COUNT=24
CONFIG_DLCI_MAX=8
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Misc devices
#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=y
+
#
# USB support
#
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
-# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_NLS is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# CONFIG_CRYPTO is not set
-#
-# Hardware crypto devices
-#
-
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc1
-# Sun Jul 9 14:13:35 2006
+# Linux kernel version: 2.6.20-rc1
+# Sat Dec 16 06:05:45 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
CONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not set
-CONFIG_SYSCTL=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
CONFIG_ARCH_IXP23XX=y
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
CONFIG_IO_36=y
#
#
# CONFIG_ARM_THUMB is not set
CONFIG_CPU_BIG_ENDIAN=y
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+# CONFIG_IWMMXT is not set
#
# Bus support
#
CONFIG_PCI=y
+# CONFIG_PCI_MULTITHREAD_PROBE is not set
# CONFIG_PCI_DEBUG is not set
#
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_SX8 is not set
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
# ATA/ATAPI/MFM/RLL support
#
CONFIG_IDE=y
+CONFIG_IDE_MAX_HWIFS=4
CONFIG_BLK_DEV_IDE=y
#
# CONFIG_BLK_DEV_OFFBOARD is not set
# CONFIG_BLK_DEV_GENERIC is not set
# CONFIG_BLK_DEV_OPTI621 is not set
-# CONFIG_BLK_DEV_SL82C105 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
# CONFIG_IDEDMA_PCI_AUTO is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_BLK_DEV_HPT34X is not set
# CONFIG_BLK_DEV_HPT366 is not set
+# CONFIG_BLK_DEV_JMICRON is not set
# CONFIG_BLK_DEV_SC1200 is not set
# CONFIG_BLK_DEV_PIIX is not set
# CONFIG_BLK_DEV_IT821X is not set
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIIMAGE=y
+# CONFIG_BLK_DEV_SL82C105 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
#
# CONFIG_RAID_ATTRS is not set
CONFIG_SCSI=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
CONFIG_SCSI_PROC_FS=y
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_CONSTANTS is not set
# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
#
-# SCSI Transport Attributes
+# SCSI Transports
#
# CONFIG_SCSI_SPI_ATTRS is not set
# CONFIG_SCSI_FC_ATTRS is not set
# CONFIG_SCSI_ISCSI_ATTRS is not set
# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
#
# SCSI low-level drivers
# CONFIG_SCSI_AIC7XXX is not set
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
# CONFIG_SCSI_DPT_I2O is not set
+# CONFIG_SCSI_ARCMSR is not set
# CONFIG_MEGARAID_NEWGEN is not set
# CONFIG_MEGARAID_LEGACY is not set
# CONFIG_MEGARAID_SAS is not set
-# CONFIG_SCSI_SATA is not set
# CONFIG_SCSI_HPTIOP is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
-# CONFIG_SCSI_IPR is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
# CONFIG_SCSI_LPFC is not set
# CONFIG_SCSI_DC395x is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
#
# Ethernet (10000 Mbit)
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
# Wan interfaces
#
CONFIG_WAN=y
-# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
CONFIG_HDLC=y
CONFIG_HDLC_RAW=y
# CONFIG_WANXL is not set
# CONFIG_PC300 is not set
# CONFIG_FARSYNC is not set
+# CONFIG_DSCC4 is not set
CONFIG_DLCI=y
CONFIG_DLCI_COUNT=24
CONFIG_DLCI_MAX=8
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SIS5595 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
# CONFIG_SENSORS_VIA686A is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_VT8231 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Misc devices
#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=y
+
#
# USB support
#
# CONFIG_USB_DEVICEFS is not set
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
# CONFIG_USB_LIBUSUAL is not set
#
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
-# CONFIG_USB_CY7C63 is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGETKIT is not set
-# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_SISUSBVGA is not set
# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
#
# USB DSL modem support
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
-# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# CONFIG_CRYPTO is not set
-#
-# Hardware crypto devices
-#
-
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc1
-# Sun Jul 9 14:15:23 2006
+# Linux kernel version: 2.6.20-rc1
+# Sat Dec 16 06:05:51 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_ARCH_MTD_XIP=y
CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
-CONFIG_SYSCTL=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP23XX is not set
# CONFIG_PXA_SHARPSL is not set
# CONFIG_MACH_TRIZEPS4 is not set
CONFIG_PXA27x=y
-CONFIG_IWMMXT=y
#
# Processor Type
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
#
# Processor Features
#
# CONFIG_ARM_THUMB is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+CONFIG_IWMMXT=y
CONFIG_XSCALE_PMU=y
#
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
#
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_CDROM_PKTCDVD is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
# CONFIG_KEYBOARD_LKKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_NVRAM is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_RAW_DRIVER is not set
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_HWMON_VID is not set
# CONFIG_SENSORS_ABITUGURU is not set
# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_HWMON_DEBUG_CHIP is not set
#
# Misc devices
#
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
# CONFIG_FB_S1D13XXX is not set
CONFIG_FB_PXA=y
# CONFIG_FB_PXA_PARAMETERS is not set
+# CONFIG_FB_MBX is not set
# CONFIG_FB_VIRTUAL is not set
#
# Generic devices
#
CONFIG_SND_AC97_CODEC=y
-CONFIG_SND_AC97_BUS=y
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# Open Sound System
#
# CONFIG_SOUND_PRIME is not set
+CONFIG_AC97_BUS=y
+
+#
+# HID Devices
+#
+CONFIG_HID=y
#
# USB support
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
# CONFIG_FS_POSIX_ACL is not set
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
# CONFIG_TMPFS is not set
# CONFIG_HUGETLB_PAGE is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
-# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
CONFIG_DEBUG_INFO=y
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# CONFIG_CRYPTO is not set
-#
-# Hardware crypto devices
-#
-
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.18-rc1
-# Sun Jul 9 14:16:20 2006
+# Linux kernel version: 2.6.20-rc1
+# Sat Dec 16 06:05:18 2006
#
CONFIG_ARM=y
+# CONFIG_GENERIC_TIME is not set
CONFIG_MMU=y
CONFIG_GENERIC_HARDIRQS=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_GENERIC_IRQ_PROBE=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_VECTORS_BASE=0xffff0000
CONFIG_LOCALVERSION_AUTO=y
# CONFIG_SWAP is not set
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
-CONFIG_SYSCTL=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
-CONFIG_UID16=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
CONFIG_BUG=y
CONFIG_ELF_CORE=y
CONFIG_BASE_FULL=y
-CONFIG_RT_MUTEXES=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
CONFIG_SHMEM=y
CONFIG_SLAB=y
CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
# CONFIG_TINY_SHMEM is not set
CONFIG_BASE_SMALL=0
# CONFIG_SLOB is not set
#
# Block layer
#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
#
# IO Schedulers
# CONFIG_ARCH_NETX is not set
# CONFIG_ARCH_H720X is not set
# CONFIG_ARCH_IMX is not set
-# CONFIG_ARCH_IOP3XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IOP13XX is not set
# CONFIG_ARCH_IXP4XX is not set
# CONFIG_ARCH_IXP2000 is not set
# CONFIG_ARCH_IXP23XX is not set
#
# Atmel AT91 System-on-Chip
#
-
-#
-# Atmel AT91 Processors
-#
CONFIG_ARCH_AT91RM9200=y
# CONFIG_ARCH_AT91SAM9260 is not set
# CONFIG_ARCH_AT91SAM9261 is not set
# CONFIG_MACH_KB9200 is not set
# CONFIG_MACH_KAFA is not set
+#
+# AT91 Board Options
+#
+
#
# AT91 Feature Selections
#
#
CONFIG_CPU_32=y
CONFIG_CPU_ARM920T=y
-CONFIG_CPU_32v4=y
+CONFIG_CPU_32v4T=y
CONFIG_CPU_ABRT_EV4T=y
CONFIG_CPU_CACHE_V4WT=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_V4WB=y
CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
#
# Processor Features
CONFIG_UNIX=y
CONFIG_XFRM=y
# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
# CONFIG_NET_KEY is not set
CONFIG_INET=y
# CONFIG_IP_MULTICAST is not set
# CONFIG_INET_TUNNEL is not set
CONFIG_INET_XFRM_MODE_TRANSPORT=y
CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
CONFIG_INET_DIAG=y
CONFIG_INET_TCP_DIAG=y
# CONFIG_TCP_CONG_ADVANCED is not set
-CONFIG_TCP_CONG_BIC=y
-# CONFIG_IPV6 is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+CONFIG_IPV6=y
+# CONFIG_IPV6_PRIVACY is not set
+# CONFIG_IPV6_ROUTER_PREF is not set
+# CONFIG_INET6_AH is not set
+# CONFIG_INET6_ESP is not set
+# CONFIG_INET6_IPCOMP is not set
+# CONFIG_IPV6_MIP6 is not set
# CONFIG_INET6_XFRM_TUNNEL is not set
# CONFIG_INET6_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET6_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET6_XFRM_MODE_BEET is not set
+# CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION is not set
+# CONFIG_IPV6_SIT is not set
+# CONFIG_IPV6_TUNNEL is not set
+# CONFIG_IPV6_MULTIPLE_TABLES is not set
# CONFIG_NETWORK_SECMARK is not set
# CONFIG_NETFILTER is not set
# CONFIG_ATALK is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NFTL is not set
# CONFIG_INFTL is not set
# CONFIG_RFD_FTL is not set
+# CONFIG_SSFDC is not set
#
# RAM/ROM/Flash chip drivers
#
# CONFIG_BLK_DEV_COW_COMMON is not set
# CONFIG_BLK_DEV_LOOP is not set
-# CONFIG_BLK_DEV_NBD is not set
+CONFIG_BLK_DEV_NBD=y
# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=8192
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
CONFIG_BLK_DEV_INITRD=y
# CONFIG_CDROM_PKTCDVD is not set
# CONFIG_ATA_OVER_ETH is not set
#
# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
-#
-# Ftape, the floppy tape device driver
-#
-
#
# PCMCIA character devices
#
# TPM devices
#
# CONFIG_TCG_TPM is not set
-# CONFIG_TELCLOCK is not set
#
# I2C support
#
# I2C Hardware Bus support
#
+# CONFIG_I2C_AT91 is not set
# CONFIG_I2C_OCORES is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
# CONFIG_I2C_STUB is not set
#
# Dallas's 1-wire bus
#
+# CONFIG_W1 is not set
#
# Hardware Monitoring support
# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
# CONFIG_SENSORS_SMSC47M1 is not set
# CONFIG_SENSORS_SMSC47M192 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_VT1211 is not set
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83791D is not set
# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
# CONFIG_SENSORS_W83627EHF is not set
#
# Misc devices
#
+# CONFIG_TIFM_CORE is not set
#
# LED devices
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
-CONFIG_VIDEO_V4L2=y
#
# Digital Video Broadcasting Devices
#
# CONFIG_FIRMWARE_EDID is not set
# CONFIG_FB is not set
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
#
# Sound
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=y
+
#
# USB support
#
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_MULTITHREAD_PROBE is not set
# CONFIG_USB_OTG is not set
#
#
# may also be needed; see USB_STORAGE Help for more information
#
-# CONFIG_USB_STORAGE is not set
# CONFIG_USB_LIBUSUAL is not set
#
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_USBNET is not set
CONFIG_USB_MON=y
#
# CONFIG_USB_EMI62 is not set
# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_LEGOTOWER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_LED is not set
-# CONFIG_USB_CY7C63 is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
# CONFIG_USB_CYTHERM is not set
-# CONFIG_USB_PHIDGETKIT is not set
-# CONFIG_USB_PHIDGETSERVO is not set
+# CONFIG_USB_PHIDGET is not set
# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
# CONFIG_USB_APPLEDISPLAY is not set
# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
# CONFIG_USB_TEST is not set
#
# CONFIG_USB_GADGETFS is not set
# CONFIG_USB_FILE_STORAGE is not set
# CONFIG_USB_G_SERIAL is not set
+# CONFIG_USB_MIDI_GADGET is not set
#
# MMC/SD Card support
CONFIG_MMC=y
# CONFIG_MMC_DEBUG is not set
CONFIG_MMC_BLOCK=y
-CONFIG_MMC_AT91RM9200=y
+# CONFIG_MMC_AT91 is not set
+# CONFIG_MMC_TIFM_SD is not set
#
# Real Time Clock
# CONFIG_EXT2_FS_XATTR is not set
# CONFIG_EXT2_FS_XIP is not set
# CONFIG_EXT3_FS is not set
+# CONFIG_EXT4DEV_FS is not set
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
# Pseudo filesystems
#
CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
# CONFIG_CONFIGFS_FS is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
-# CONFIG_CIFS_DEBUG2 is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
#
# CONFIG_NLS is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Profiling support
#
# Kernel hacking
#
# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
# CONFIG_MAGIC_SYSRQ is not set
# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_DEBUG_KOBJECT is not set
CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_LIST is not set
CONFIG_FRAME_POINTER=y
-# CONFIG_UNWIND_INFO is not set
CONFIG_FORCED_INLINING=y
# CONFIG_RCU_TORTURE_TEST is not set
CONFIG_DEBUG_USER=y
#
# CONFIG_CRYPTO is not set
-#
-# Hardware crypto devices
-#
-
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
CALL(sys_ni_syscall) /* was sys_profil */
CALL(sys_statfs)
/* 100 */ CALL(sys_fstatfs)
- CALL(sys_ni_syscall)
+ CALL(sys_ni_syscall) /* sys_ioperm */
CALL(OBSOLETE(ABI(sys_socketcall, sys_oabi_socketcall)))
CALL(sys_syslog)
CALL(sys_setitimer)
/* 120 */ CALL(sys_clone_wrapper)
CALL(sys_setdomainname)
CALL(sys_newuname)
- CALL(sys_ni_syscall)
+ CALL(sys_ni_syscall) /* modify_ldt */
CALL(sys_adjtimex)
/* 125 */ CALL(sys_mprotect)
CALL(sys_sigprocmask)
CALL(sys_bdflush)
/* 135 */ CALL(sys_sysfs)
CALL(sys_personality)
- CALL(sys_ni_syscall) /* CALL(_sys_afs_syscall) */
+ CALL(sys_ni_syscall) /* reserved for afs_syscall */
CALL(sys_setfsuid16)
CALL(sys_setfsgid16)
/* 140 */ CALL(sys_llseek)
CALL(sys_arm_mremap)
CALL(sys_setresuid16)
/* 165 */ CALL(sys_getresuid16)
- CALL(sys_ni_syscall)
+ CALL(sys_ni_syscall) /* vm86 */
CALL(sys_ni_syscall) /* was sys_query_module */
CALL(sys_poll)
CALL(sys_nfsservctl)
/* 185 */ CALL(sys_capset)
CALL(sys_sigaltstack_wrapper)
CALL(sys_sendfile)
- CALL(sys_ni_syscall)
- CALL(sys_ni_syscall)
+ CALL(sys_ni_syscall) /* getpmsg */
+ CALL(sys_ni_syscall) /* putpmsg */
/* 190 */ CALL(sys_vfork_wrapper)
CALL(sys_getrlimit)
CALL(sys_mmap2)
CALL(sys_readlinkat)
CALL(sys_fchmodat)
CALL(sys_faccessat)
+/* 335 */ CALL(sys_ni_syscall) /* eventually pselect6 */
+ CALL(sys_ni_syscall) /* eventually ppoll */
+ CALL(sys_unshare)
+ CALL(sys_set_robust_list)
+ CALL(sys_get_robust_list)
+/* 340 */ CALL(sys_splice)
+ CALL(sys_arm_sync_file_range)
+ CALL(sys_tee)
+ CALL(sys_vmsplice)
+ CALL(sys_move_pages)
+/* 345 */ CALL(sys_getcpu)
+ CALL(sys_ni_syscall) /* eventually epoll_pwait */
#ifndef syscalls_counted
.equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
#define syscalls_counted
"edsp",
"java",
"iwmmxt",
+ "crunch",
NULL
};
{
return sys_fadvise64_64(fd, offset, len, advice);
}
+
+/*
+ * Yet more syscall fsckage - we can't fit sys_sync_file_range's
+ * arguments into the available registers with EABI. So, let's
+ * create an ARM specific syscall for this which has _sane_
+ * arguments. (This incidentally also has an ABI-independent
+ * argument layout.)
+ */
+asmlinkage long sys_arm_sync_file_range(int fd, unsigned int flags,
+ loff_t offset, loff_t nbytes)
+{
+ return sys_sync_file_range(fd, offset, nbytes, flags);
+}
platform_device_register(&ep93xx_rtc_device);
platform_device_register(&ep93xx_ohci_device);
+
+#ifdef CONFIG_CRUNCH
+ elf_hwcap |= HWCAP_CRUNCH;
+#endif
}
MACHINE_START(IQ81340MC, "Intel IQ81340MC")
/* Maintainer: Dan Williams <dan.j.williams@intel.com> */
- .phys_io = PHYS_IO,
- .io_pg_offst = IO_PG_OFFSET,
+ .phys_io = IOP13XX_PMMR_PHYS_MEM_BASE,
+ .io_pg_offst = (IOP13XX_PMMR_VIRT_MEM_BASE >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
.map_io = iop13xx_map_io,
.init_irq = iop13xx_init_irq,
.timer = &iq81340mc_timer,
- .boot_params = BOOT_PARAM_OFFSET,
.init_machine = iq81340mc_init,
MACHINE_END
MACHINE_START(IQ81340SC, "Intel IQ81340SC")
/* Maintainer: Dan Williams <dan.j.williams@intel.com> */
- .phys_io = PHYS_IO,
- .io_pg_offst = IO_PG_OFFSET,
+ .phys_io = IOP13XX_PMMR_PHYS_MEM_BASE,
+ .io_pg_offst = (IOP13XX_PMMR_VIRT_MEM_BASE >> 18) & 0xfffc,
+ .boot_params = 0x00000100,
.map_io = iop13xx_map_io,
.init_irq = iop13xx_init_irq,
.timer = &iq81340sc_timer,
- .boot_params = BOOT_PARAM_OFFSET,
.init_machine = iq81340sc_init,
MACHINE_END
iop13xx_cp6_restore(cp_flags);
}
-static struct irqchip iop13xx_irqchip0 = {
+static struct irq_chip iop13xx_irqchip1 = {
+ .name = "IOP13xx-1",
.ack = iop13xx_irq_mask0,
.mask = iop13xx_irq_mask0,
.unmask = iop13xx_irq_unmask0,
};
-static struct irqchip iop13xx_irqchip1 = {
+static struct irq_chip iop13xx_irqchip2 = {
+ .name = "IOP13xx-2",
.ack = iop13xx_irq_mask1,
.mask = iop13xx_irq_mask1,
.unmask = iop13xx_irq_unmask1,
};
-static struct irqchip iop13xx_irqchip2 = {
+static struct irq_chip iop13xx_irqchip3 = {
+ .name = "IOP13xx-3",
.ack = iop13xx_irq_mask2,
.mask = iop13xx_irq_mask2,
.unmask = iop13xx_irq_unmask2,
};
-static struct irqchip iop13xx_irqchip3 = {
+static struct irq_chip iop13xx_irqchip4 = {
+ .name = "IOP13xx-4",
.ack = iop13xx_irq_mask3,
.mask = iop13xx_irq_mask3,
.unmask = iop13xx_irq_unmask3,
for(i = 0; i < NR_IOP13XX_IRQS; i++) {
if (i < 32)
- set_irq_chip(i, &iop13xx_irqchip0);
- else if (i < 64)
set_irq_chip(i, &iop13xx_irqchip1);
- else if (i < 96)
+ else if (i < 64)
set_irq_chip(i, &iop13xx_irqchip2);
- else
+ else if (i < 96)
set_irq_chip(i, &iop13xx_irqchip3);
+ else
+ set_irq_chip(i, &iop13xx_irqchip4);
- set_irq_handler(i, do_level_IRQ);
+ set_irq_handler(i, handle_level_irq);
set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
}
#ifdef CONFIG_MTD_PHYSMAP
iq8134x_flash_resource.end = iq8134x_flash_resource.start +
- iq8134x_probe_flash_size();
+ iq8134x_probe_flash_size() - 1;
if (iq8134x_flash_resource.end > iq8134x_flash_resource.start)
iop13xx_devices[plat_idx++] = &iq8134x_flash;
else
config MACH_AML_M5900
bool "AML M5900 Series"
select CPU_S3C2410
+ select PM_SIMTEC if PM
help
Say Y here if you are using the American Microsystems M5900 Series
<http://www.amltd.com>
config MACH_ANUBIS
bool "Simtec Electronics ANUBIS"
select CPU_S3C2440
+ select PM_SIMTEC if PM
help
Say Y here if you are using the Simtec Electronics ANUBIS
development system
config MACH_OSIRIS
bool "Simtec IM2440D20 (OSIRIS) module"
select CPU_S3C2440
+ select PM_SIMTEC if PM
help
Say Y here if you are using the Simtec IM2440D20 module, also
known as the Osiris.
config ARCH_BAST
bool "Simtec Electronics BAST (EB2410ITX)"
select CPU_S3C2410
+ select PM_SIMTEC if PM
select ISA
help
Say Y here if you are using the Simtec Electronics EB2410ITX
config PM_H1940
bool
- depends on PM
help
Internal node for H1940 and related PM
config ARCH_H1940
bool "IPAQ H1940"
select CPU_S3C2410
- select PM_H1940
+ select PM_H1940 if PM
help
Say Y here if you are using the HP IPAQ H1940
config MACH_VR1000
bool "Thorcom VR1000"
+ select PM_SIMTEC if PM
select CPU_S3C2410
help
Say Y here if you are using the Thorcom VR1000 board.
config MACH_RX3715
bool "HP iPAQ rx3715"
select CPU_S3C2440
- select PM_H1940
+ select PM_H1940 if PM
help
Say Y here if you are using the HP iPAQ rx3715.
config S3C2410_PM
bool
- depends on CONFIG_PM
help
Power Management code common to S3C2410 and better
bool
depends on ARCH_S3C2410
select S3C2410_CLOCK
- select S3C2410_PM
+ select S3C2410_PM if PM
help
Support for S3C2410 and S3C2410A family from the S3C24XX line
of Samsung Mobile CPUs.
config S3C2412_PM
bool
- default y if PM
- depends on CPU_S3C2412
help
Internal config node to apply S3C2412 power management
config CPU_S3C2412
bool
depends on ARCH_S3C2410
+ select S3C2412_PM if PM
help
Support for the S3C2412 and S3C2413 SoCs from the S3C24XX line
bool
depends on ARCH_S3C2410
select S3C2410_CLOCK
- select S3C2410_PM
+ select S3C2410_PM if PM
select CPU_S3C244X
help
Support for S3C2440 Samsung Mobile CPU based systems.
bool
depends on ARCH_S3C2420
select S3C2410_CLOCK
- select S3C2410_PM
+ select S3C2410_PM if PM
select CPU_S3C244X
help
Support for S3C2442 Samsung Mobile CPU based systems.
config PM_SIMTEC
bool
- depends on PM && (ARCH_BAST || MACH_VR1000 || MACH_AML_M5900)
- default y
+ help
+ Common power management code for systems that are
+ compatible with the Simtec style of power management
config S3C2410_LOWLEVEL_UART_PORT
int "S3C2410 UART to use for low-level messages"
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/hardware.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
/* linux/arch/arm/mach-s3c2410/dma.c
*
- * (c) 2003-2005,2006 Simtec Electronics
+ * Copyright (c) 2003-2005,2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 DMA core
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
- * Modifications:
*/
#define irqdbf(x...)
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/dm9000.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <asm/arch/h1940-latch.h>
#include <asm/arch/fb.h>
-#include <linux/serial_core.h>
-
#include "clock.h"
#include "devs.h"
#include "cpu.h"
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/delay.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/kthread.h>
#include <asm/arch/regs-gpio.h>
#include <asm/arch/iic.h>
-#include <linux/serial_core.h>
-
#include "s3c2410.h"
#include "clock.h"
#include "devs.h"
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/string.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/mtd/map.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/device.h>
+#include <linux/serial_core.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
static struct platform_device vr1000_led3 = {
.name = "s3c24xx_led",
- .id = 1,
+ .id = 3,
.dev = {
.platform_data = &vr1000_led3_pdata,
},
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <asm/io.h>
#include <asm/arch/map.h>
-#include <asm/arch/regs-serial.h>
#include <asm/arch/regs-gpio.h>
#include <asm/arch/regs-mem.h>
#include <linux/crc32.h>
#include <linux/ioport.h>
#include <linux/delay.h>
+#include <linux/serial_core.h>
#include <asm/cacheflush.h>
#include <asm/hardware.h>
#include <linux/clk.h>
#include <linux/mutex.h>
#include <linux/delay.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/map.h>
#include <asm/hardware.h>
#include <asm/io.h>
+#include <asm/arch/regs-serial.h>
#include <asm/arch/regs-clock.h>
#include <asm/arch/regs-gpio.h>
+#include "s3c2410.h"
#include "clock.h"
#include "cpu.h"
/* linux/arch/arm/mach-s3c2410/s3c2410-dma.c
*
- * (c) 2006 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 DMA selection
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sysdev.h>
+#include <linux/serial_core.h>
#include <asm/dma.h>
#include <asm/arch/dma.h>
return s3c24xx_dma_init_map(&s3c2410_dma_sel);
}
+#if defined(CONFIG_CPU_S3C2410)
static struct sysdev_driver s3c2410_dma_driver = {
.add = s3c2410_dma_add,
};
}
arch_initcall(s3c2410_dma_init);
+#endif
+#if defined(CONFIG_CPU_S3C2442)
/* S3C2442 DMA contains the same selection table as the S3C2410 */
-
static struct sysdev_driver s3c2442_dma_driver = {
.add = s3c2410_dma_add,
};
}
arch_initcall(s3c2442_dma_init);
-
+#endif
}
-int s3c2410_pm_resume(struct sys_device *dev)
+static int s3c2410_pm_resume(struct sys_device *dev)
{
unsigned long tmp;
return 0;
}
+#if defined(CONFIG_CPU_S3C2410)
static struct sysdev_driver s3c2410_pm_driver = {
.add = s3c2410_pm_add,
.resume = s3c2410_pm_resume,
}
arch_initcall(s3c2410_pm_drvinit);
+#endif
+#if defined(CONFIG_CPU_S3C2440)
static struct sysdev_driver s3c2440_pm_driver = {
.add = s3c2410_pm_add,
.resume = s3c2410_pm_resume,
}
arch_initcall(s3c2440_pm_drvinit);
+#endif
+#if defined(CONFIG_CPU_S3C2442)
static struct sysdev_driver s3c2442_pm_driver = {
.add = s3c2410_pm_add,
.resume = s3c2410_pm_resume,
}
arch_initcall(s3c2442_pm_drvinit);
+#endif
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/sysdev.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
/* Initial IO mappings */
static struct map_desc s3c2410_iodesc[] __initdata = {
- IODESC_ENT(USBHOST),
IODESC_ENT(CLKPWR),
IODESC_ENT(LCD),
IODESC_ENT(TIMER),
- IODESC_ENT(ADC),
IODESC_ENT(WATCHDOG),
};
#include <linux/clk.h>
#include <linux/mutex.h>
#include <linux/delay.h>
+#include <linux/serial_core.h>
+
+#include <asm/mach/map.h>
#include <asm/hardware.h>
#include <asm/io.h>
+#include <asm/arch/regs-serial.h>
#include <asm/arch/regs-clock.h>
#include <asm/arch/regs-gpio.h>
+#include "s3c2412.h"
#include "clock.h"
#include "cpu.h"
* set the correct muxing at initialisation
*/
-int s3c2412_clkcon_enable(struct clk *clk, int enable)
+static int s3c2412_clkcon_enable(struct clk *clk, int enable)
{
unsigned int clocks = clk->ctrlbit;
unsigned long clkcon;
struct clk *src_1;
};
-struct clk_init clks_src[] __initdata = {
+static struct clk_init clks_src[] __initdata = {
{
.clk = &clk_usysclk,
.bit = S3C2412_CLKSRC_USBCLK_HCLK,
/* clocks to add straight away */
-struct clk *clks[] __initdata = {
+static struct clk *clks[] __initdata = {
&clk_ext,
&clk_usb_bus,
&clk_erefclk,
/* linux/arch/arm/mach-s3c2410/s3c2412-dma.c
*
- * (c) 2006 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2412 DMA selection
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sysdev.h>
+#include <linux/serial_core.h>
#include <asm/dma.h>
#include <asm/arch/dma.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/sysdev.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/mach/arch.h>
IODESC_ENT(CLKPWR),
IODESC_ENT(LCD),
IODESC_ENT(TIMER),
- IODESC_ENT(ADC),
IODESC_ENT(WATCHDOG),
};
{
unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN);
unsigned long clkdivn;
- struct clk *clk_h;
- struct clk *clk_p;
- struct clk *clk_upll;
+ struct clk *clock_h;
+ struct clk *clock_p;
+ struct clk *clock_upll;
printk("S3C2440: Clock Support, DVS %s\n",
(camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off");
- clk_p = clk_get(NULL, "pclk");
- clk_h = clk_get(NULL, "hclk");
- clk_upll = clk_get(NULL, "upll");
+ clock_p = clk_get(NULL, "pclk");
+ clock_h = clk_get(NULL, "hclk");
+ clock_upll = clk_get(NULL, "upll");
- if (IS_ERR(clk_p) || IS_ERR(clk_h) || IS_ERR(clk_upll)) {
+ if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) {
printk(KERN_ERR "S3C2440: Failed to get parent clocks\n");
return -EINVAL;
}
/* check rate of UPLL, and if it is near 96MHz, then change
* to using half the UPLL rate for the system */
- if (clk_get_rate(clk_upll) > (94 * MHZ)) {
- clk_usb_bus.rate = clk_get_rate(clk_upll) / 2;
+ if (clk_get_rate(clock_upll) > (94 * MHZ)) {
+ clk_usb_bus.rate = clk_get_rate(clock_upll) / 2;
mutex_lock(&clocks_mutex);
mutex_unlock(&clocks_mutex);
}
- s3c2440_clk_cam.parent = clk_h;
- s3c2440_clk_ac97.parent = clk_p;
- s3c2440_clk_cam_upll.parent = clk_upll;
+ s3c2440_clk_cam.parent = clock_h;
+ s3c2440_clk_ac97.parent = clock_p;
+ s3c2440_clk_cam_upll.parent = clock_upll;
s3c24xx_register_clock(&s3c2440_clk_ac97);
s3c24xx_register_clock(&s3c2440_clk_cam);
/* linux/arch/arm/mach-s3c2410/s3c2440-dma.c
*
- * (c) 2006 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2440 DMA selection
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/sysdev.h>
+#include <linux/serial_core.h>
#include <asm/dma.h>
#include <asm/arch/dma.h>
#include <linux/timer.h>
#include <linux/init.h>
#include <linux/platform_device.h>
+#include <linux/serial_core.h>
#include <linux/sysdev.h>
#include <linux/clk.h>
#include <asm/io.h>
#include <asm/irq.h>
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-gpioj.h>
-#include <asm/arch/regs-dsc.h>
-
#include "s3c2440.h"
-#include "clock.h"
#include "devs.h"
#include "cpu.h"
-#include "pm.h"
static struct sys_device s3c2440_sysdev = {
.cls = &s3c2440_sysclass,
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
- * Modifications:
- * 24-Aug-2004 BJD Start of S3C2440 CPU support
- * 04-Nov-2004 BJD Added s3c2440_init_uarts()
- * 04-Jan-2005 BJD Moved uart init to cpu code
- * 10-Jan-2005 BJD Moved 2440 specific init here
- * 14-Jan-2005 BJD Split the clock initialisation code
*/
#ifdef CONFIG_CPU_S3C2440
-
extern int s3c2440_init(void);
-
-extern void s3c2440_map_io(struct map_desc *mach_desc, int size);
-
-extern void s3c2440_init_uarts(struct s3c2410_uartcfg *cfg, int no);
-
-extern void s3c2440_init_clocks(int xtal);
-
#else
-#define s3c2440_init_clocks NULL
-#define s3c2440_init_uarts NULL
-#define s3c2440_map_io NULL
#define s3c2440_init NULL
#endif
{
unsigned long camdivn = __raw_readl(S3C2440_CAMDIVN);
unsigned long clkdivn;
- struct clk *clk_h;
- struct clk *clk_p;
- struct clk *clk_upll;
+ struct clk *clock_h;
+ struct clk *clock_p;
+ struct clk *clock_upll;
printk("S3C2442: Clock Support, DVS %s\n",
(camdivn & S3C2440_CAMDIVN_DVSEN) ? "on" : "off");
- clk_p = clk_get(NULL, "pclk");
- clk_h = clk_get(NULL, "hclk");
- clk_upll = clk_get(NULL, "upll");
+ clock_p = clk_get(NULL, "pclk");
+ clock_h = clk_get(NULL, "hclk");
+ clock_upll = clk_get(NULL, "upll");
- if (IS_ERR(clk_p) || IS_ERR(clk_h) || IS_ERR(clk_upll)) {
+ if (IS_ERR(clock_p) || IS_ERR(clock_h) || IS_ERR(clock_upll)) {
printk(KERN_ERR "S3C2442: Failed to get parent clocks\n");
return -EINVAL;
}
/* check rate of UPLL, and if it is near 96MHz, then change
* to using half the UPLL rate for the system */
- if (clk_get_rate(clk_upll) > (94 * MHZ)) {
- clk_usb_bus.rate = clk_get_rate(clk_upll) / 2;
+ if (clk_get_rate(clock_upll) > (94 * MHZ)) {
+ clk_usb_bus.rate = clk_get_rate(clock_upll) / 2;
mutex_lock(&clocks_mutex);
mutex_unlock(&clocks_mutex);
}
- s3c2442_clk_cam.parent = clk_h;
- s3c2442_clk_cam_upll.parent = clk_upll;
+ s3c2442_clk_cam.parent = clock_h;
+ s3c2442_clk_cam_upll.parent = clock_upll;
s3c24xx_register_clock(&s3c2442_clk_cam);
s3c24xx_register_clock(&s3c2442_clk_cam_upll);
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
-#include <linux/platform_device.h>
+#include <linux/serial_core.h>
#include <linux/sysdev.h>
-#include <linux/clk.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <asm/hardware.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#include <asm/arch/regs-clock.h>
-#include <asm/arch/regs-serial.h>
-#include <asm/arch/regs-gpio.h>
-#include <asm/arch/regs-gpioj.h>
-#include <asm/arch/regs-dsc.h>
#include "s3c2442.h"
-#include "clock.h"
-#include "devs.h"
#include "cpu.h"
-#include "pm.h"
static struct sys_device s3c2442_sysdev = {
.cls = &s3c2442_sysclass,
#include <linux/list.h>
#include <linux/timer.h>
#include <linux/init.h>
+#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/sysdev.h>
#include <linux/clk.h>
IODESC_ENT(TIMER),
IODESC_ENT(WATCHDOG),
IODESC_ENT(LCD),
- IODESC_ENT(ADC),
- IODESC_ENT(USBHOST),
};
/* uart initialisation */
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
- *
- * Modifications:
- * 20-Aug-2004 BJD Created
*/
extern int usb_simtec_init(void);
if (pfn >= 0x100000 && (__pfn_to_phys(pfn) & ~SUPERSECTION_MASK))
return NULL;
+ size = PAGE_ALIGN(size);
+
area = get_vm_area(size, VM_IOREMAP);
if (!area)
return NULL;
}
__setup("noalign", noalign_setup);
+#ifndef CONFIG_SMP
+void adjust_cr(unsigned long mask, unsigned long set)
+{
+ unsigned long flags;
+
+ mask &= ~CR_A;
+
+ set &= mask;
+
+ local_irq_save(flags);
+
+ cr_no_alignment = (cr_no_alignment & ~mask) | set;
+ cr_alignment = (cr_alignment & ~mask) | set;
+
+ set_cr((get_cr() & ~mask) | set);
+
+ local_irq_restore(flags);
+}
+#endif
+
struct mem_types {
unsigned int prot_pte;
unsigned int prot_l1;
* linux/arch/arm/mm/proc-xsc3.S
*
* Original Author: Matthew Gilbert
- * Current Maintainer: Deepak Saxena <dsaxena@plexity.net>
+ * Current Maintainer: Lennert Buytenhek <buytenh@wantstofly.org>
*
* Copyright 2004 (C) Intel Corp.
* Copyright 2005 (c) MontaVista Software, Inc.
$(obj)/zImage.ps3: vmlinux
$(STRIP) -s -R .comment $< -o $@
+$(obj)/zImage.initrd.ps3: vmlinux
+ @echo " WARNING zImage.initrd.ps3 not supported (yet)"
+
$(obj)/uImage: vmlinux $(wrapperbits)
$(call cmd,wrap,uboot)
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.19-rc6
-# Wed Nov 22 15:33:04 2006
+# Linux kernel version: 2.6.20-rc1
+# Tue Dec 19 14:59:53 2006
#
CONFIG_PPC64=y
CONFIG_64BIT=y
CONFIG_GENERIC_HARDIRQS=y
CONFIG_IRQ_PER_CPU=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+CONFIG_ARCH_HAS_ILOG2_U64=y
CONFIG_GENERIC_HWEIGHT=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_GENERIC_FIND_NEXT_BIT=y
CONFIG_PPC_UDBG_16550=y
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_AUDIT_ARCH=y
+CONFIG_GENERIC_BUG=y
# CONFIG_DEFAULT_UIMAGE is not set
#
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_CPUSETS=y
+CONFIG_SYSFS_DEPRECATED=y
# CONFIG_RELAY is not set
CONFIG_INITRAMFS_SOURCE=""
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
# CONFIG_APUS is not set
# CONFIG_PPC_PSERIES is not set
# CONFIG_PPC_ISERIES is not set
+# CONFIG_PPC_MPC52xx is not set
# CONFIG_PPC_PMAC is not set
# CONFIG_PPC_MAPLE is not set
# CONFIG_PPC_PASEMI is not set
CONFIG_PPC_CELL=y
CONFIG_PPC_CELL_NATIVE=y
CONFIG_PPC_IBM_CELL_BLADE=y
-CONFIG_UDBG_RTAS_CONSOLE=y
CONFIG_PPC_PS3=y
+CONFIG_PPC_NATIVE=y
+CONFIG_UDBG_RTAS_CONSOLE=y
# CONFIG_U3_DART is not set
CONFIG_PPC_RTAS=y
# CONFIG_RTAS_ERROR_LOGGING is not set
CONFIG_PS3_HTAB_SIZE=20
# CONFIG_PS3_DYNAMIC_DMA is not set
CONFIG_PS3_USE_LPAR_ADDR=y
+CONFIG_PS3_VUART=y
#
# Kernel options
#
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
# CONFIG_HZ_1000 is not set
CONFIG_HZ=250
CONFIG_PREEMPT_NONE=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCIEPORTBUS=y
+# CONFIG_PCI_MULTITHREAD_PROBE is not set
# CONFIG_PCI_DEBUG is not set
#
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_FIB_HASH=y
-# CONFIG_IP_PNP is not set
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
CONFIG_NET_IPIP=y
# CONFIG_NET_IPGRE is not set
# CONFIG_IP_MROUTE is not set
# CONFIG_TCP_CONG_ADVANCED is not set
CONFIG_TCP_CONG_CUBIC=y
CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
#
# IP: Virtual Server Configuration
#
# Core Netfilter Configuration
#
-# CONFIG_NETFILTER_NETLINK is not set
-# CONFIG_NETFILTER_XTABLES is not set
+CONFIG_NETFILTER_NETLINK=m
+CONFIG_NETFILTER_NETLINK_QUEUE=m
+CONFIG_NETFILTER_NETLINK_LOG=m
+# CONFIG_NF_CONNTRACK_ENABLED is not set
+CONFIG_NETFILTER_XTABLES=m
+CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
+CONFIG_NETFILTER_XT_TARGET_DSCP=m
+CONFIG_NETFILTER_XT_TARGET_MARK=m
+CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
+CONFIG_NETFILTER_XT_TARGET_NFLOG=m
+CONFIG_NETFILTER_XT_MATCH_COMMENT=m
+CONFIG_NETFILTER_XT_MATCH_DCCP=m
+CONFIG_NETFILTER_XT_MATCH_DSCP=m
+CONFIG_NETFILTER_XT_MATCH_ESP=m
+CONFIG_NETFILTER_XT_MATCH_LENGTH=m
+CONFIG_NETFILTER_XT_MATCH_LIMIT=m
+CONFIG_NETFILTER_XT_MATCH_MAC=m
+CONFIG_NETFILTER_XT_MATCH_MARK=m
+CONFIG_NETFILTER_XT_MATCH_POLICY=m
+CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
+CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
+CONFIG_NETFILTER_XT_MATCH_QUOTA=m
+CONFIG_NETFILTER_XT_MATCH_REALM=m
+CONFIG_NETFILTER_XT_MATCH_SCTP=m
+CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
+CONFIG_NETFILTER_XT_MATCH_STRING=m
+CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
+CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
#
# IP: Netfilter Configuration
#
-CONFIG_IP_NF_CONNTRACK=y
-# CONFIG_IP_NF_CT_ACCT is not set
-# CONFIG_IP_NF_CONNTRACK_MARK is not set
-# CONFIG_IP_NF_CONNTRACK_EVENTS is not set
-CONFIG_IP_NF_CT_PROTO_SCTP=y
-CONFIG_IP_NF_FTP=m
-CONFIG_IP_NF_IRC=m
-# CONFIG_IP_NF_NETBIOS_NS is not set
-CONFIG_IP_NF_TFTP=m
-CONFIG_IP_NF_AMANDA=m
-# CONFIG_IP_NF_PPTP is not set
-# CONFIG_IP_NF_H323 is not set
-# CONFIG_IP_NF_SIP is not set
CONFIG_IP_NF_QUEUE=m
+CONFIG_IP_NF_IPTABLES=m
+CONFIG_IP_NF_MATCH_IPRANGE=m
+CONFIG_IP_NF_MATCH_TOS=m
+CONFIG_IP_NF_MATCH_RECENT=m
+CONFIG_IP_NF_MATCH_ECN=m
+CONFIG_IP_NF_MATCH_AH=m
+CONFIG_IP_NF_MATCH_TTL=m
+CONFIG_IP_NF_MATCH_OWNER=m
+CONFIG_IP_NF_MATCH_ADDRTYPE=m
+CONFIG_IP_NF_FILTER=m
+CONFIG_IP_NF_TARGET_REJECT=m
+CONFIG_IP_NF_TARGET_LOG=m
+CONFIG_IP_NF_TARGET_ULOG=m
+CONFIG_IP_NF_TARGET_TCPMSS=m
+CONFIG_IP_NF_MANGLE=m
+CONFIG_IP_NF_TARGET_TOS=m
+CONFIG_IP_NF_TARGET_ECN=m
+CONFIG_IP_NF_TARGET_TTL=m
+CONFIG_IP_NF_RAW=m
+CONFIG_IP_NF_ARPTABLES=m
+CONFIG_IP_NF_ARPFILTER=m
+CONFIG_IP_NF_ARP_MANGLE=m
#
# IPv6: Netfilter Configuration (EXPERIMENTAL)
#
# CONFIG_IP6_NF_QUEUE is not set
+# CONFIG_IP6_NF_IPTABLES is not set
#
# DCCP Configuration (EXPERIMENTAL)
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
+CONFIG_NET_CLS_ROUTE=y
#
# Network testing
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_SX8 is not set
+# CONFIG_BLK_DEV_UB is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=131072
# CONFIG_BLK_DEV_IDECD is not set
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_IDE_TASK_IOCTL is not set
#
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_BLK_DEV_GENERIC=y
# CONFIG_BLK_DEV_OPTI621 is not set
-# CONFIG_BLK_DEV_SL82C105 is not set
CONFIG_BLK_DEV_IDEDMA_PCI=y
# CONFIG_BLK_DEV_IDEDMA_FORCED is not set
CONFIG_IDEDMA_PCI_AUTO=y
# CONFIG_BLK_DEV_PDC202XX_NEW is not set
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIIMAGE=y
+# CONFIG_BLK_DEV_SL82C105 is not set
# CONFIG_BLK_DEV_SLC90E66 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_VIA82CXXX is not set
# SCSI device support
#
# CONFIG_RAID_ATTRS is not set
-# CONFIG_SCSI is not set
+CONFIG_SCSI=m
+# CONFIG_SCSI_TGT is not set
# CONFIG_SCSI_NETLINK is not set
+CONFIG_SCSI_PROC_FS=y
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+CONFIG_BLK_DEV_SR=m
+# CONFIG_BLK_DEV_SR_VENDOR is not set
+CONFIG_CHR_DEV_SG=m
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+
+#
+# SCSI low-level drivers
+#
+# CONFIG_ISCSI_TCP is not set
+# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
+# CONFIG_SCSI_3W_9XXX is not set
+# CONFIG_SCSI_ACARD is not set
+# CONFIG_SCSI_AACRAID is not set
+# CONFIG_SCSI_AIC7XXX is not set
+# CONFIG_SCSI_AIC7XXX_OLD is not set
+# CONFIG_SCSI_AIC79XX is not set
+# CONFIG_SCSI_AIC94XX is not set
+# CONFIG_SCSI_ARCMSR is not set
+# CONFIG_MEGARAID_NEWGEN is not set
+# CONFIG_MEGARAID_LEGACY is not set
+# CONFIG_MEGARAID_SAS is not set
+# CONFIG_SCSI_HPTIOP is not set
+# CONFIG_SCSI_BUSLOGIC is not set
+# CONFIG_SCSI_DMX3191D is not set
+# CONFIG_SCSI_EATA is not set
+# CONFIG_SCSI_FUTURE_DOMAIN is not set
+# CONFIG_SCSI_GDTH is not set
+# CONFIG_SCSI_IPS is not set
+# CONFIG_SCSI_INITIO is not set
+# CONFIG_SCSI_INIA100 is not set
+# CONFIG_SCSI_STEX is not set
+# CONFIG_SCSI_SYM53C8XX_2 is not set
+# CONFIG_SCSI_QLOGIC_1280 is not set
+# CONFIG_SCSI_QLA_FC is not set
+# CONFIG_SCSI_QLA_ISCSI is not set
+# CONFIG_SCSI_LPFC is not set
+# CONFIG_SCSI_DC395x is not set
+# CONFIG_SCSI_DC390T is not set
+# CONFIG_SCSI_DEBUG is not set
+# CONFIG_SCSI_SRP is not set
#
# Serial ATA (prod) and Parallel ATA (experimental) drivers
# Fusion MPT device support
#
# CONFIG_FUSION is not set
+# CONFIG_FUSION_SPI is not set
+# CONFIG_FUSION_FC is not set
+# CONFIG_FUSION_SAS is not set
#
# IEEE 1394 (FireWire) support
#
# Macintosh device drivers
#
+# CONFIG_MAC_EMUMOUSEBTN is not set
# CONFIG_WINDFARM is not set
#
#
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
-CONFIG_BONDING=y
+CONFIG_BONDING=m
# CONFIG_EQUALIZER is not set
CONFIG_TUN=y
# CONFIG_R8169 is not set
# CONFIG_SIS190 is not set
CONFIG_SKGE=m
-# CONFIG_SKY2 is not set
+CONFIG_SKY2=m
# CONFIG_SK98LIN is not set
-# CONFIG_TIGON3 is not set
+CONFIG_TIGON3=y
# CONFIG_BNX2 is not set
-CONFIG_SPIDER_NET=m
+CONFIG_SPIDER_NET=y
# CONFIG_QLA3XXX is not set
#
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
# CONFIG_HIPPI is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
+# CONFIG_NET_FC is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
# CONFIG_NETPOLL is not set
# CONFIG_DIGIEPCA is not set
# CONFIG_MOXA_INTELLIO is not set
# CONFIG_MOXA_SMARTIO is not set
+# CONFIG_MOXA_SMARTIO_NEW is not set
# CONFIG_ISI is not set
# CONFIG_SYNCLINK is not set
# CONFIG_SYNCLINKMP is not set
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
# CONFIG_SERIAL_JSM is not set
+CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_UNIX98_PTYS=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_HVC_DRIVER=y
#
# CONFIG_PCIPCWATCHDOG is not set
# CONFIG_WDTPCI is not set
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
# CONFIG_HW_RANDOM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
# Digital Video Broadcasting Devices
#
# CONFIG_DVB is not set
+# CONFIG_USB_DABUSB is not set
#
# Graphics support
#
CONFIG_FIRMWARE_EDID=y
# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
#
# Console display driver support
#
# CONFIG_SOUND is not set
+#
+# HID Devices
+#
+CONFIG_HID=m
+
#
# USB support
#
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB_ARCH_HAS_OHCI=y
CONFIG_USB_ARCH_HAS_EHCI=y
-# CONFIG_USB is not set
+CONFIG_USB=m
+# CONFIG_USB_DEBUG is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_BANDWIDTH is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_MULTITHREAD_PROBE is not set
+# CONFIG_USB_OTG is not set
+
+#
+# USB Host Controller Drivers
+#
+CONFIG_USB_EHCI_HCD=m
+# CONFIG_USB_EHCI_SPLIT_ISO is not set
+# CONFIG_USB_EHCI_ROOT_HUB_TT is not set
+# CONFIG_USB_EHCI_TT_NEWSCHED is not set
+# CONFIG_USB_ISP116X_HCD is not set
+CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_OHCI_BIG_ENDIAN is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USB_SL811_HCD is not set
+
+#
+# USB Device Class drivers
+#
+# CONFIG_USB_ACM is not set
+# CONFIG_USB_PRINTER is not set
#
# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
#
+#
+# may also be needed; see USB_STORAGE Help for more information
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+# CONFIG_USB_STORAGE_DATAFAB is not set
+# CONFIG_USB_STORAGE_FREECOM is not set
+# CONFIG_USB_STORAGE_ISD200 is not set
+# CONFIG_USB_STORAGE_DPCM is not set
+# CONFIG_USB_STORAGE_USBAT is not set
+# CONFIG_USB_STORAGE_SDDR09 is not set
+# CONFIG_USB_STORAGE_SDDR55 is not set
+# CONFIG_USB_STORAGE_JUMPSHOT is not set
+# CONFIG_USB_STORAGE_ALAUDA is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_LIBUSUAL is not set
+
+#
+# USB Input Devices
+#
+# CONFIG_USB_HID is not set
+
+#
+# USB HID Boot Protocol drivers
+#
+# CONFIG_USB_KBD is not set
+# CONFIG_USB_MOUSE is not set
+# CONFIG_USB_AIPTEK is not set
+# CONFIG_USB_WACOM is not set
+# CONFIG_USB_ACECAD is not set
+# CONFIG_USB_KBTAB is not set
+# CONFIG_USB_POWERMATE is not set
+# CONFIG_USB_TOUCHSCREEN is not set
+# CONFIG_USB_YEALINK is not set
+# CONFIG_USB_XPAD is not set
+# CONFIG_USB_ATI_REMOTE is not set
+# CONFIG_USB_ATI_REMOTE2 is not set
+# CONFIG_USB_KEYSPAN_REMOTE is not set
+# CONFIG_USB_APPLETOUCH is not set
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET_MII is not set
+# CONFIG_USB_USBNET is not set
+CONFIG_USB_MON=y
+
+#
+# USB port drivers
+#
+
+#
+# USB Serial Converter support
+#
+# CONFIG_USB_SERIAL is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_AUERSWALD is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_PHIDGET is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_SISUSBVGA is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_TEST is not set
+
+#
+# USB DSL modem support
+#
+
#
# USB Gadget Support
#
#
# InfiniBand support
#
-CONFIG_INFINIBAND=y
+CONFIG_INFINIBAND=m
CONFIG_INFINIBAND_USER_MAD=m
CONFIG_INFINIBAND_USER_ACCESS=m
CONFIG_INFINIBAND_ADDR_TRANS=y
CONFIG_INFINIBAND_IPOIB=m
CONFIG_INFINIBAND_IPOIB_DEBUG=y
CONFIG_INFINIBAND_IPOIB_DEBUG_DATA=y
+# CONFIG_INFINIBAND_SRP is not set
+# CONFIG_INFINIBAND_ISER is not set
#
# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
# DMA Devices
#
+#
+# Virtualization
+#
+
#
# File systems
#
#
# Network File Systems
#
-CONFIG_NFS_FS=m
+CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
-CONFIG_NFSD=m
-CONFIG_NFSD_V2_ACL=y
-CONFIG_NFSD_V3=y
-CONFIG_NFSD_V3_ACL=y
-# CONFIG_NFSD_V4 is not set
-CONFIG_NFSD_TCP=y
-CONFIG_LOCKD=m
+# CONFIG_NFSD is not set
+CONFIG_ROOT_NFS=y
+CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
-CONFIG_EXPORTFS=m
-CONFIG_NFS_ACL_SUPPORT=m
+CONFIG_NFS_ACL_SUPPORT=y
CONFIG_NFS_COMMON=y
-CONFIG_SUNRPC=m
+CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_NLS_KOI8_U is not set
# CONFIG_NLS_UTF8 is not set
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
+
#
# Library routines
#
+CONFIG_BITREVERSE=y
# CONFIG_CRC_CCITT is not set
# CONFIG_CRC16 is not set
CONFIG_CRC32=y
CONFIG_ZLIB_DEFLATE=m
CONFIG_TEXTSEARCH=y
CONFIG_TEXTSEARCH_KMP=m
+CONFIG_TEXTSEARCH_BM=m
+CONFIG_TEXTSEARCH_FSM=m
CONFIG_PLIST=y
+CONFIG_IOMAP_COPY=y
#
# Instrumentation Support
# CONFIG_ENABLE_MUST_CHECK is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=15
CONFIG_DETECT_SOFTLOCKUP=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
# CONFIG_DEBUG_INFO is not set
-CONFIG_DEBUG_FS=y
# CONFIG_DEBUG_VM is not set
# CONFIG_DEBUG_LIST is not set
# CONFIG_FORCED_INLINING is not set
-# CONFIG_HEADERS_CHECK is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_STACK_USAGE is not set
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_MANAGER=y
CONFIG_CRYPTO_HMAC=y
+# CONFIG_CRYPTO_XCBC is not set
# CONFIG_CRYPTO_NULL is not set
# CONFIG_CRYPTO_MD4 is not set
CONFIG_CRYPTO_MD5=m
# CONFIG_CRYPTO_SHA512 is not set
# CONFIG_CRYPTO_WP512 is not set
# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_CBC=m
+# CONFIG_CRYPTO_LRW is not set
CONFIG_CRYPTO_DES=m
# CONFIG_CRYPTO_BLOWFISH is not set
# CONFIG_CRYPTO_TWOFISH is not set
{ .type = "plb5", },
{ .type = "plb4", },
{ .type = "opb", },
+ { .type = "ebc", },
{},
};
DBG(" class: 0x%x\n", dev->class);
dev->current_state = 4; /* unknown power state */
+ dev->error_state = pci_channel_io_normal;
if (!strcmp(type, "pci") || !strcmp(type, "pciex")) {
/* a PCI-PCI bridge */
/*
* Old machines just have a list of interrupt numbers
- * and no interrupt-controller nodes.
+ * and no interrupt-controller nodes. We also have dodgy
+ * cases where the APPL,interrupts property is completely
+ * missing behind pci-pci bridges and we have to get it
+ * from the parent (the bridge itself, as apple just wired
+ * everything together on these)
*/
- ints = get_property(device, "AAPL,interrupts", &intlen);
+ while (device) {
+ ints = get_property(device, "AAPL,interrupts", &intlen);
+ if (ints != NULL)
+ break;
+ device = device->parent;
+ if (device && strcmp(device->type, "pci") != 0)
+ break;
+ }
if (ints == NULL)
return -EINVAL;
intlen /= sizeof(u32);
return -EINVAL;
if (old_ctx != NULL) {
+ struct mcontext __user *mctx;
+
+ /*
+ * old_ctx might not be 16-byte aligned, in which
+ * case old_ctx->uc_mcontext won't be either.
+ * Because we have the old_ctx->uc_pad2 field
+ * before old_ctx->uc_mcontext, we need to round down
+ * from &old_ctx->uc_mcontext to a 16-byte boundary.
+ */
+ mctx = (struct mcontext __user *)
+ ((unsigned long) &old_ctx->uc_mcontext & ~0xfUL);
if (!access_ok(VERIFY_WRITE, old_ctx, sizeof(*old_ctx))
- || save_user_regs(regs, &old_ctx->uc_mcontext, 0)
+ || save_user_regs(regs, mctx, 0)
|| put_sigset_t(&old_ctx->uc_sigmask, ¤t->blocked)
- || __put_user(to_user_ptr(&old_ctx->uc_mcontext),
- &old_ctx->uc_regs))
+ || __put_user(to_user_ptr(mctx), &old_ctx->uc_regs))
return -EFAULT;
}
if (new_ctx == NULL)
obj-$(CONFIG_PPC_PMAC) += powermac/
endif
endif
+obj-$(CONFIG_PPC_MPC52xx) += 52xx/
obj-$(CONFIG_PPC_CHRP) += chrp/
obj-$(CONFIG_4xx) += 4xx/
-obj-$(CONFIG_PPC_MPC52xx) += 52xx/
obj-$(CONFIG_PPC_83xx) += 83xx/
obj-$(CONFIG_PPC_85xx) += 85xx/
obj-$(CONFIG_PPC_86xx) += 86xx/
*/
#define SPIDER_DISABLE_PREFETCH
-#define MAX_SPIDERS 2
+#define MAX_SPIDERS 3
static struct spider_pci_bus {
void __iomem *regs;
#include "interrupt.h"
#include "spu_priv1_mmio.h"
+static DEFINE_MUTEX(add_spumem_mutex);
+
struct spu_pdata {
- int nid;
struct device_node *devnode;
struct spu_priv1 __iomem *priv1;
};
EXPORT_SYMBOL_GPL(spu_devnode);
-static int __init find_spu_node_id(struct device_node *spe)
-{
- const unsigned int *id;
- struct device_node *cpu;
- cpu = spe->parent->parent;
- id = get_property(cpu, "node-id", NULL);
- return id ? *id : 0;
-}
-
static int __init cell_spuprop_present(struct spu *spu, struct device_node *spe,
const char *prop)
{
- static DEFINE_MUTEX(add_spumem_mutex);
-
const struct address_prop {
unsigned long address;
unsigned int len;
start_pfn = p->address >> PAGE_SHIFT;
nr_pages = ((unsigned long)p->len + PAGE_SIZE - 1) >> PAGE_SHIFT;
- pgdata = NODE_DATA(spu_get_pdata(spu)->nid);
+ pgdata = NODE_DATA(spu->node);
zone = pgdata->node_zones;
/* XXX rethink locking here */
{
unsigned int isrc;
const u32 *tmp;
+ int nid;
/* Get the interrupt source unit from the device-tree */
tmp = get_property(np, "isrc", NULL);
return -ENODEV;
isrc = tmp[0];
+ tmp = get_property(np->parent->parent, "node-id", NULL);
+ if (!tmp) {
+ printk(KERN_WARNING "%s: can't find node-id\n", __FUNCTION__);
+ nid = spu->node;
+ } else
+ nid = tmp[0];
+
/* Add the node number */
- isrc |= spu->node << IIC_IRQ_NODE_SHIFT;
+ isrc |= nid << IIC_IRQ_NODE_SHIFT;
/* Now map interrupts of all 3 classes */
spu->irqs[0] = irq_create_mapping(NULL, IIC_IRQ_CLASS_0 | isrc);
return ret;
}
-static int spu_map_resource(struct device_node *node, int nr,
- void __iomem** virt, unsigned long *phys)
+static int spu_map_resource(struct spu *spu, int nr,
+ void __iomem** virt, unsigned long *phys)
{
+ struct device_node *np = spu_get_pdata(spu)->devnode;
+ unsigned long start_pfn, nr_pages;
+ struct pglist_data *pgdata;
+ struct zone *zone;
struct resource resource = { };
+ unsigned long len;
int ret;
- ret = of_address_to_resource(node, nr, &resource);
+ ret = of_address_to_resource(np, nr, &resource);
if (ret)
goto out;
if (phys)
*phys = resource.start;
- *virt = ioremap(resource.start, resource.end - resource.start);
+ len = resource.end - resource.start + 1;
+ *virt = ioremap(resource.start, len);
if (!*virt)
ret = -EINVAL;
+ start_pfn = resource.start >> PAGE_SHIFT;
+ nr_pages = (len + PAGE_SIZE - 1) >> PAGE_SHIFT;
+
+ pgdata = NODE_DATA(spu->node);
+ zone = pgdata->node_zones;
+
+ /* XXX rethink locking here */
+ mutex_lock(&add_spumem_mutex);
+ ret = __add_pages(zone, start_pfn, nr_pages);
+ mutex_unlock(&add_spumem_mutex);
+
out:
return ret;
}
-static int __init spu_map_device(struct spu *spu, struct device_node *node)
+static int __init spu_map_device(struct spu *spu)
{
+ struct device_node *np = spu_get_pdata(spu)->devnode;
int ret = -ENODEV;
- spu->name = get_property(node, "name", NULL);
+
+ spu->name = get_property(np, "name", NULL);
if (!spu->name)
goto out;
- ret = spu_map_resource(node, 0, (void __iomem**)&spu->local_store,
- &spu->local_store_phys);
+ ret = spu_map_resource(spu, 0, (void __iomem**)&spu->local_store,
+ &spu->local_store_phys);
if (ret) {
pr_debug("spu_new: failed to map %s resource 0\n",
- node->full_name);
+ np->full_name);
goto out;
}
- ret = spu_map_resource(node, 1, (void __iomem**)&spu->problem,
- &spu->problem_phys);
+ ret = spu_map_resource(spu, 1, (void __iomem**)&spu->problem,
+ &spu->problem_phys);
if (ret) {
pr_debug("spu_new: failed to map %s resource 1\n",
- node->full_name);
+ np->full_name);
goto out_unmap;
}
- ret = spu_map_resource(node, 2, (void __iomem**)&spu->priv2,
- NULL);
+ ret = spu_map_resource(spu, 2, (void __iomem**)&spu->priv2, NULL);
if (ret) {
pr_debug("spu_new: failed to map %s resource 2\n",
- node->full_name);
+ np->full_name);
goto out_unmap;
}
if (!firmware_has_feature(FW_FEATURE_LPAR))
- ret = spu_map_resource(node, 3,
- (void __iomem**)&spu_get_pdata(spu)->priv1, NULL);
+ ret = spu_map_resource(spu, 3,
+ (void __iomem**)&spu_get_pdata(spu)->priv1, NULL);
if (ret) {
pr_debug("spu_new: failed to map %s resource 3\n",
- node->full_name);
+ np->full_name);
goto out_unmap;
}
- pr_debug("spu_new: %s maps:\n", node->full_name);
+ pr_debug("spu_new: %s maps:\n", np->full_name);
pr_debug(" local store : 0x%016lx -> 0x%p\n",
spu->local_store_phys, spu->local_store);
pr_debug(" problem state : 0x%016lx -> 0x%p\n",
spu->problem_phys, spu->problem);
pr_debug(" priv2 : 0x%p\n", spu->priv2);
pr_debug(" priv1 : 0x%p\n",
- spu_get_pdata(spu)->priv1);
+ spu_get_pdata(spu)->priv1);
return 0;
ret = -ENOMEM;
goto out;
}
+ spu_get_pdata(spu)->devnode = of_node_get(spe);
- spu->node = find_spu_node_id(spe);
+ spu->node = of_node_to_nid(spe);
if (spu->node >= MAX_NUMNODES) {
printk(KERN_WARNING "SPE %s on node %d ignored,"
" node number too big\n", spe->full_name, spu->node);
goto out_free;
}
- spu_get_pdata(spu)->nid = of_node_to_nid(spe);
- if (spu_get_pdata(spu)->nid == -1)
- spu_get_pdata(spu)->nid = 0;
-
- ret = spu_map_device(spu, spe);
+ ret = spu_map_device(spu);
/* try old method */
if (ret)
ret = spu_map_device_old(spu, spe);
if (ret)
goto out_unmap;
- spu_get_pdata(spu)->devnode = of_node_get(spe);
-
pr_debug(KERN_DEBUG "Using SPE %s %p %p %p %p %d\n", spu->name,
spu->local_store, spu->problem, spu_get_pdata(spu)->priv1,
spu->priv2, spu->number);
config VIOPATH
bool
- depends on VIOCONS || VIODASD || VIOCD || VIOTAPE || VETH
+ depends on VIOCONS || VIODASD || VIOCD || VIOTAPE || ISERIES_VETH
default y
#include <asm/iseries/hv_lp_event.h>
#include <asm/iseries/hv_lp_config.h>
#include <asm/iseries/vio.h>
+#include <asm/firmware.h>
MODULE_DESCRIPTION("iSeries Virtual DASD");
MODULE_AUTHOR("Dave Boutcher");
{
int rc;
+ if (!firmware_has_feature(FW_FEATURE_ISERIES)) {
+ rc = -ENODEV;
+ goto early_fail;
+ }
+
/* Try to open to our host lp */
if (viopath_hostLp == HvLpIndexInvalid)
vio_set_hostlp();
/* Kensington Bluetooth USB adapter */
{ USB_DEVICE(0x047d, 0x105d), .driver_info = HCI_RESET },
+ { USB_DEVICE(0x047d, 0x105e), .driver_info = HCI_WRONG_SCO_MTU },
/* ISSC Bluetooth Adapter v3.1 */
{ USB_DEVICE(0x1131, 0x1001), .driver_info = HCI_RESET },
#include <asm/iseries/hv_types.h>
#include <asm/iseries/hv_lp_event.h>
#include <asm/iseries/vio.h>
+#include <asm/firmware.h>
#define VIOCD_DEVICE "iseries/vcd"
struct proc_dir_entry *e;
int ret = 0;
+ if (!firmware_has_feature(FW_FEATURE_ISERIES))
+ return -ENODEV;
+
if (viopath_hostLp == HvLpIndexInvalid) {
vio_set_hostlp();
/* If we don't have a host, bail out */
int (*context_dtor) (struct drm_device * dev, int context);
int (*kernel_context_switch) (struct drm_device * dev, int old,
int new);
- void (*kernel_context_switch_unlock) (struct drm_device * dev,
- drm_lock_t *lock);
+ void (*kernel_context_switch_unlock) (struct drm_device * dev);
int (*vblank_wait) (struct drm_device * dev, unsigned int *sequence);
int (*vblank_wait2) (struct drm_device * dev, unsigned int *sequence);
int (*dri_library_name) (struct drm_device *dev, char *buf);
extern unsigned long drm_core_get_map_ofs(drm_map_t * map);
extern unsigned long drm_core_get_reg_ofs(struct drm_device *dev);
-#ifndef pci_pretty_name
-#define pci_pretty_name(dev) ""
-#endif
-
#endif /* __KERNEL__ */
#endif
* modules but is required by the Sparc driver.
*/
if (dev->driver->kernel_context_switch_unlock)
- dev->driver->kernel_context_switch_unlock(dev, &lock);
+ dev->driver->kernel_context_switch_unlock(dev);
else {
drm_lock_transfer(dev, &dev->lock.hw_lock->lock,
DRM_KERNEL_CONTEXT);
if (!dev)
return -ENOMEM;
- pci_enable_device(pdev);
+ ret = pci_enable_device(pdev);
+ if (ret)
+ goto err_g1;
if ((ret = drm_fill_in_dev(dev, pdev, ent, driver))) {
printk(KERN_ERR "DRM: Fill_in_dev failed.\n");
- goto err_g1;
+ goto err_g2;
}
if ((ret = drm_get_head(dev, &dev->primary)))
- goto err_g1;
+ goto err_g2;
DRM_INFO("Initialized %s %d.%d.%d %s on minor %d\n",
driver->name, driver->major, driver->minor, driver->patchlevel,
return 0;
- err_g1:
+err_g2:
+ pci_disable_device(pdev);
+err_g1:
drm_free(dev, sizeof(*dev), DRM_MEM_STUB);
return ret;
}
int err;
class = class_create(owner, name);
- if (!class) {
- err = -ENOMEM;
+ if (IS_ERR(class)) {
+ err = PTR_ERR(class);
goto err_out;
}
MKDEV(DRM_MAJOR, head->minor),
&(head->dev->pdev)->dev,
"card%d", head->minor);
- if (!class_dev) {
- err = -ENOMEM;
+ if (IS_ERR(class_dev)) {
+ err = PTR_ERR(class_dev);
goto err_out;
}
{
drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
unsigned long irqflags;
- struct list_head *list, *tmp;
+ struct list_head *list, *tmp, hits, *hit;
+ int nhits, nrects, slice[2], upper[2], lower[2], i;
+ unsigned counter[2] = { atomic_read(&dev->vbl_received),
+ atomic_read(&dev->vbl_received2) };
+ drm_drawable_info_t *drw;
+ drm_i915_sarea_t *sarea_priv = dev_priv->sarea_priv;
+ u32 cpp = dev_priv->cpp;
+ u32 cmd = (cpp == 4) ? (XY_SRC_COPY_BLT_CMD |
+ XY_SRC_COPY_BLT_WRITE_ALPHA |
+ XY_SRC_COPY_BLT_WRITE_RGB)
+ : XY_SRC_COPY_BLT_CMD;
+ u32 pitchropcpp = (sarea_priv->pitch * cpp) | (0xcc << 16) |
+ (cpp << 23) | (1 << 24);
+ RING_LOCALS;
DRM_DEBUG("\n");
+ INIT_LIST_HEAD(&hits);
+
+ nhits = nrects = 0;
+
spin_lock_irqsave(&dev_priv->swaps_lock, irqflags);
+ /* Find buffer swaps scheduled for this vertical blank */
list_for_each_safe(list, tmp, &dev_priv->vbl_swaps.head) {
drm_i915_vbl_swap_t *vbl_swap =
list_entry(list, drm_i915_vbl_swap_t, head);
- atomic_t *counter = vbl_swap->pipe ? &dev->vbl_received2 :
- &dev->vbl_received;
-
- if ((atomic_read(counter) - vbl_swap->sequence) <= (1<<23)) {
- drm_drawable_info_t *drw;
-
- spin_unlock(&dev_priv->swaps_lock);
-
- spin_lock(&dev->drw_lock);
-
- drw = drm_get_drawable_info(dev, vbl_swap->drw_id);
-
- if (drw) {
- int i, num_rects = drw->num_rects;
- drm_clip_rect_t *rect = drw->rects;
- drm_i915_sarea_t *sarea_priv =
- dev_priv->sarea_priv;
- u32 cpp = dev_priv->cpp;
- u32 cmd = (cpp == 4) ? (XY_SRC_COPY_BLT_CMD |
- XY_SRC_COPY_BLT_WRITE_ALPHA |
- XY_SRC_COPY_BLT_WRITE_RGB)
- : XY_SRC_COPY_BLT_CMD;
- u32 pitchropcpp = (sarea_priv->pitch * cpp) |
- (0xcc << 16) | (cpp << 23) |
- (1 << 24);
- RING_LOCALS;
-
- i915_kernel_lost_context(dev);
-
- BEGIN_LP_RING(6);
-
- OUT_RING(GFX_OP_DRAWRECT_INFO);
- OUT_RING(0);
- OUT_RING(0);
- OUT_RING(sarea_priv->width |
- sarea_priv->height << 16);
- OUT_RING(sarea_priv->width |
- sarea_priv->height << 16);
- OUT_RING(0);
- ADVANCE_LP_RING();
+ if ((counter[vbl_swap->pipe] - vbl_swap->sequence) > (1<<23))
+ continue;
+
+ list_del(list);
+ dev_priv->swaps_pending--;
- sarea_priv->ctxOwner = DRM_KERNEL_CONTEXT;
+ spin_unlock(&dev_priv->swaps_lock);
+ spin_lock(&dev->drw_lock);
- for (i = 0; i < num_rects; i++, rect++) {
- BEGIN_LP_RING(8);
+ drw = drm_get_drawable_info(dev, vbl_swap->drw_id);
+
+ if (!drw) {
+ spin_unlock(&dev->drw_lock);
+ drm_free(vbl_swap, sizeof(*vbl_swap), DRM_MEM_DRIVER);
+ spin_lock(&dev_priv->swaps_lock);
+ continue;
+ }
- OUT_RING(cmd);
- OUT_RING(pitchropcpp);
- OUT_RING((rect->y1 << 16) | rect->x1);
- OUT_RING((rect->y2 << 16) | rect->x2);
- OUT_RING(sarea_priv->front_offset);
- OUT_RING((rect->y1 << 16) | rect->x1);
- OUT_RING(pitchropcpp & 0xffff);
- OUT_RING(sarea_priv->back_offset);
+ list_for_each(hit, &hits) {
+ drm_i915_vbl_swap_t *swap_cmp =
+ list_entry(hit, drm_i915_vbl_swap_t, head);
+ drm_drawable_info_t *drw_cmp =
+ drm_get_drawable_info(dev, swap_cmp->drw_id);
- ADVANCE_LP_RING();
- }
+ if (drw_cmp &&
+ drw_cmp->rects[0].y1 > drw->rects[0].y1) {
+ list_add_tail(list, hit);
+ break;
}
+ }
- spin_unlock(&dev->drw_lock);
+ spin_unlock(&dev->drw_lock);
- spin_lock(&dev_priv->swaps_lock);
+ /* List of hits was empty, or we reached the end of it */
+ if (hit == &hits)
+ list_add_tail(list, hits.prev);
- list_del(list);
+ nhits++;
- drm_free(vbl_swap, sizeof(*vbl_swap), DRM_MEM_DRIVER);
+ spin_lock(&dev_priv->swaps_lock);
+ }
+
+ if (nhits == 0) {
+ spin_unlock_irqrestore(&dev_priv->swaps_lock, irqflags);
+ return;
+ }
+
+ spin_unlock(&dev_priv->swaps_lock);
- dev_priv->swaps_pending--;
+ i915_kernel_lost_context(dev);
+
+ BEGIN_LP_RING(6);
+
+ OUT_RING(GFX_OP_DRAWRECT_INFO);
+ OUT_RING(0);
+ OUT_RING(0);
+ OUT_RING(sarea_priv->width | sarea_priv->height << 16);
+ OUT_RING(sarea_priv->width | sarea_priv->height << 16);
+ OUT_RING(0);
+
+ ADVANCE_LP_RING();
+
+ sarea_priv->ctxOwner = DRM_KERNEL_CONTEXT;
+
+ upper[0] = upper[1] = 0;
+ slice[0] = max(sarea_priv->pipeA_h / nhits, 1);
+ slice[1] = max(sarea_priv->pipeB_h / nhits, 1);
+ lower[0] = sarea_priv->pipeA_y + slice[0];
+ lower[1] = sarea_priv->pipeB_y + slice[0];
+
+ spin_lock(&dev->drw_lock);
+
+ /* Emit blits for buffer swaps, partitioning both outputs into as many
+ * slices as there are buffer swaps scheduled in order to avoid tearing
+ * (based on the assumption that a single buffer swap would always
+ * complete before scanout starts).
+ */
+ for (i = 0; i++ < nhits;
+ upper[0] = lower[0], lower[0] += slice[0],
+ upper[1] = lower[1], lower[1] += slice[1]) {
+ if (i == nhits)
+ lower[0] = lower[1] = sarea_priv->height;
+
+ list_for_each(hit, &hits) {
+ drm_i915_vbl_swap_t *swap_hit =
+ list_entry(hit, drm_i915_vbl_swap_t, head);
+ drm_clip_rect_t *rect;
+ int num_rects, pipe;
+ unsigned short top, bottom;
+
+ drw = drm_get_drawable_info(dev, swap_hit->drw_id);
+
+ if (!drw)
+ continue;
+
+ rect = drw->rects;
+ pipe = swap_hit->pipe;
+ top = upper[pipe];
+ bottom = lower[pipe];
+
+ for (num_rects = drw->num_rects; num_rects--; rect++) {
+ int y1 = max(rect->y1, top);
+ int y2 = min(rect->y2, bottom);
+
+ if (y1 >= y2)
+ continue;
+
+ BEGIN_LP_RING(8);
+
+ OUT_RING(cmd);
+ OUT_RING(pitchropcpp);
+ OUT_RING((y1 << 16) | rect->x1);
+ OUT_RING((y2 << 16) | rect->x2);
+ OUT_RING(sarea_priv->front_offset);
+ OUT_RING((y1 << 16) | rect->x1);
+ OUT_RING(pitchropcpp & 0xffff);
+ OUT_RING(sarea_priv->back_offset);
+
+ ADVANCE_LP_RING();
+ }
}
}
- spin_unlock_irqrestore(&dev_priv->swaps_lock, irqflags);
+ spin_unlock_irqrestore(&dev->drw_lock, irqflags);
+
+ list_for_each_safe(hit, tmp, &hits) {
+ drm_i915_vbl_swap_t *swap_hit =
+ list_entry(hit, drm_i915_vbl_swap_t, head);
+
+ list_del(hit);
+
+ drm_free(swap_hit, sizeof(*swap_hit), DRM_MEM_DRIVER);
+ }
}
irqreturn_t i915_driver_irq_handler(DRM_IRQ_ARGS)
/* r128_drm.h -- Public header for the r128 driver -*- linux-c -*-
* Created: Wed Apr 5 19:24:19 2000 by kevin@precisioninsight.com
*/
-/* Copyright 2000 Precision Insight, Inc., Cedar Park, Texas.
+/*
+ * Copyright 2000 Precision Insight, Inc., Cedar Park, Texas.
* Copyright 2000 VA Linux Systems, Inc., Sunnyvale, California.
* All rights reserved.
*
/* r128_drv.h -- Private header for r128 driver -*- linux-c -*-
* Created: Mon Dec 13 09:51:11 1999 by faith@precisioninsight.com
*/
-/* Copyright 1999 Precision Insight, Inc., Cedar Park, Texas.
+/*
+ * Copyright 1999 Precision Insight, Inc., Cedar Park, Texas.
* Copyright 2000 VA Linux Systems, Inc., Sunnyvale, California.
* All rights reserved.
*
/* r128_state.c -- State support for r128 -*- linux-c -*-
* Created: Thu Jan 27 02:53:43 2000 by gareth@valinux.com
*/
-/* Copyright 2000 VA Linux Systems, Inc., Sunnyvale, California.
+/*
+ * Copyright 2000 VA Linux Systems, Inc., Sunnyvale, California.
* All Rights Reserved.
*
* Permission is hereby granted, free of charge, to any person obtaining a
return 0;
}
-/*
- * we expect offsets passed to the framebuffer to be either within video
- * memory or within AGP space
- */
-static __inline__ int r300_check_offset(drm_radeon_private_t *dev_priv,
- u32 offset)
-{
- /* we realy want to check against end of video aperture
- but this value is not being kept.
- This code is correct for now (does the same thing as the
- code that sets MC_FB_LOCATION) in radeon_cp.c */
- if (offset >= dev_priv->fb_location &&
- offset < (dev_priv->fb_location + dev_priv->fb_size))
- return 0;
- if (offset >= dev_priv->gart_vm_start &&
- offset < (dev_priv->gart_vm_start + dev_priv->gart_size))
- return 0;
- return 1;
-}
-
static __inline__ int r300_emit_carefully_checked_packet0(drm_radeon_private_t *
dev_priv,
drm_radeon_kcmd_buffer_t
case MARK_SAFE:
break;
case MARK_CHECK_OFFSET:
- if (r300_check_offset(dev_priv, (u32) values[i])) {
+ if (!radeon_check_offset(dev_priv, (u32) values[i])) {
DRM_ERROR
("Offset failed range check (reg=%04x sz=%d)\n",
reg, sz);
i = 1;
while ((k < narrays) && (i < (count + 1))) {
i++; /* skip attribute field */
- if (r300_check_offset(dev_priv, payload[i])) {
+ if (!radeon_check_offset(dev_priv, payload[i])) {
DRM_ERROR
("Offset failed range check (k=%d i=%d) while processing 3D_LOAD_VBPNTR packet.\n",
k, i);
if (k == narrays)
break;
/* have one more to process, they come in pairs */
- if (r300_check_offset(dev_priv, payload[i])) {
+ if (!radeon_check_offset(dev_priv, payload[i])) {
DRM_ERROR
("Offset failed range check (k=%d i=%d) while processing 3D_LOAD_VBPNTR packet.\n",
k, i);
if (cmd[1] & (RADEON_GMC_SRC_PITCH_OFFSET_CNTL
| RADEON_GMC_DST_PITCH_OFFSET_CNTL)) {
offset = cmd[2] << 10;
- ret = r300_check_offset(dev_priv, offset);
+ ret = !radeon_check_offset(dev_priv, offset);
if (ret) {
DRM_ERROR("Invalid bitblt first offset is %08X\n", offset);
return DRM_ERR(EINVAL);
if ((cmd[1] & RADEON_GMC_SRC_PITCH_OFFSET_CNTL) &&
(cmd[1] & RADEON_GMC_DST_PITCH_OFFSET_CNTL)) {
offset = cmd[3] << 10;
- ret = r300_check_offset(dev_priv, offset);
+ ret = !radeon_check_offset(dev_priv, offset);
if (ret) {
DRM_ERROR("Invalid bitblt second offset is %08X\n", offset);
return DRM_ERR(EINVAL);
DRM_ERROR("Invalid indx_buffer reg address %08X\n", cmd[1]);
return DRM_ERR(EINVAL);
}
- ret = r300_check_offset(dev_priv, cmd[2]);
+ ret = !radeon_check_offset(dev_priv, cmd[2]);
if (ret) {
DRM_ERROR("Invalid indx_buffer offset is %08X\n", cmd[2]);
return DRM_ERR(EINVAL);
extern drm_ioctl_desc_t radeon_ioctls[];
extern int radeon_max_ioctl;
+/* Check whether the given hardware address is inside the framebuffer or the
+ * GART area.
+ */
+static __inline__ int radeon_check_offset(drm_radeon_private_t *dev_priv,
+ u64 off)
+{
+ u32 fb_start = dev_priv->fb_location;
+ u32 fb_end = fb_start + dev_priv->fb_size - 1;
+ u32 gart_start = dev_priv->gart_vm_start;
+ u32 gart_end = gart_start + dev_priv->gart_size - 1;
+
+ return ((off >= fb_start && off <= fb_end) ||
+ (off >= gart_start && off <= gart_end));
+}
+
/* radeon_cp.c */
extern int radeon_cp_init(DRM_IOCTL_ARGS);
extern int radeon_cp_start(DRM_IOCTL_ARGS);
-/* radeon_irq.c -- IRQ handling for radeon -*- linux-c -*-
- *
+/* radeon_irq.c -- IRQ handling for radeon -*- linux-c -*- */
+/*
* Copyright (C) The Weather Channel, Inc. 2002. All Rights Reserved.
*
* The Weather Channel (TM) funded Tungsten Graphics to develop the
-/* radeon_mem.c -- Simple GART/fb memory manager for radeon -*- linux-c -*-
- *
+/* radeon_mem.c -- Simple GART/fb memory manager for radeon -*- linux-c -*- */
+/*
* Copyright (C) The Weather Channel, Inc. 2002. All Rights Reserved.
*
* The Weather Channel (TM) funded Tungsten Graphics to develop the
u32 *offset)
{
u64 off = *offset;
- u32 fb_start = dev_priv->fb_location;
- u32 fb_end = fb_start + dev_priv->fb_size - 1;
- u32 gart_start = dev_priv->gart_vm_start;
- u32 gart_end = gart_start + dev_priv->gart_size - 1;
+ u32 fb_end = dev_priv->fb_location + dev_priv->fb_size - 1;
struct drm_radeon_driver_file_fields *radeon_priv;
/* Hrm ... the story of the offset ... So this function converts
/* First, the best case, the offset already lands in either the
* framebuffer or the GART mapped space
*/
- if ((off >= fb_start && off <= fb_end) ||
- (off >= gart_start && off <= gart_end))
+ if (radeon_check_offset(dev_priv, off))
return 0;
/* Ok, that didn't happen... now check if we have a zero based
/* Finally, assume we aimed at a GART offset if beyond the fb */
if (off > fb_end)
- off = off - fb_end - 1 + gart_start;
+ off = off - fb_end - 1 + dev_priv->gart_vm_start;
/* Now recheck and fail if out of bounds */
- if ((off >= fb_start && off <= fb_end) ||
- (off >= gart_start && off <= gart_end)) {
+ if (radeon_check_offset(dev_priv, off)) {
DRM_DEBUG("offset fixed up to 0x%x\n", (unsigned int)off);
*offset = off;
return 0;
event.count = savage_bci_emit_event(dev_priv, event.flags);
event.count |= dev_priv->event_wrap << 16;
- DRM_COPY_TO_USER_IOCTL(&((drm_savage_event_emit_t __user *) data)->
- count, event.count, sizeof(event.count));
+ DRM_COPY_TO_USER_IOCTL((drm_savage_event_emit_t __user *) data,
+ event, sizeof(event));
return 0;
}
#include <linux/tty_flip.h>
#include <linux/sysrq.h>
+#include <asm/firmware.h>
#include <asm/iseries/vio.h>
#include <asm/iseries/hv_lp_event.h>
#include <asm/iseries/hv_call_event.h>
atomic_t wait_flag;
int rc;
+ if (!firmware_has_feature(FW_FEATURE_ISERIES))
+ return -ENODEV;
+
/* +2 for fudge */
rc = viopath_open(HvLpConfig_getPrimaryLpIndex(),
viomajorsubtype_chario, VIOCHAR_WINDOW + 2);
{
int i;
+ if (!firmware_has_feature(FW_FEATURE_ISERIES))
+ return -ENODEV;
+
printk(VIOCONS_KERN_INFO "registering console\n");
for (i = 0; i < VTTY_PORTS; i++) {
port_info[i].lp = HvLpIndexInvalid;
#include <asm/uaccess.h>
#include <asm/ioctls.h>
-
+#include <asm/firmware.h>
#include <asm/vio.h>
#include <asm/iseries/vio.h>
#include <asm/iseries/hv_lp_event.h>
int ret;
struct proc_dir_entry *e;
+ if (!firmware_has_feature(FW_FEATURE_ISERIES))
+ return -ENODEV;
+
op_struct_list = NULL;
if ((ret = add_op_structs(VIOTAPE_MAXREQ)) < 0) {
printk(VIOTAPE_KERN_WARN "couldn't allocate op structs\n");
#include <asm/abs_addr.h>
#include <asm/iseries/mf.h>
#include <asm/uaccess.h>
-
+#include <asm/firmware.h>
#include <asm/iseries/hv_lp_config.h>
#include <asm/iseries/hv_types.h>
#include <asm/iseries/hv_lp_event.h>
* Module initialization/cleanup
*/
-void __exit veth_module_cleanup(void)
+static void __exit veth_module_cleanup(void)
{
int i;
struct veth_lpar_connection *cnx;
}
module_exit(veth_module_cleanup);
-int __init veth_module_init(void)
+static int __init veth_module_init(void)
{
int i;
int rc;
+ if (!firmware_has_feature(FW_FEATURE_ISERIES))
+ return -ENODEV;
+
this_lp = HvLpConfig_getLpIndex_outline();
for (i = 0; i < HVMAXARCHITECTEDLPS; ++i) {
struct usblp {
struct usb_device *dev; /* USB device */
- struct semaphore sem; /* locks this struct, especially "dev" */
+ struct mutex mut; /* locks this struct, especially "dev" */
char *writebuf; /* write transfer_buffer */
char *readbuf; /* read transfer_buffer */
char *statusbuf; /* status transfer_buffer */
int twoints[2];
int retval = 0;
- down (&usblp->sem);
+ mutex_lock (&usblp->mut);
if (!usblp->present) {
retval = -ENODEV;
goto done;
}
done:
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
return retval;
}
static ssize_t usblp_write(struct file *file, const char __user *buffer, size_t count, loff_t *ppos)
{
struct usblp *usblp = file->private_data;
- int timeout, rv, err = 0, transfer_length = 0;
+ int timeout, intr, rv, err = 0, transfer_length = 0;
size_t writecount = 0;
while (writecount < count) {
if (rv < 0)
return writecount ? writecount : -EINTR;
}
- down (&usblp->sem);
+ intr = mutex_lock_interruptible (&usblp->mut);
+ if (intr)
+ return writecount ? writecount : -EINTR;
if (!usblp->present) {
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
return -ENODEV;
}
if (usblp->sleeping) {
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
return writecount ? writecount : -ENODEV;
}
err = usblp->writeurb->status;
} else
err = usblp_check_status(usblp, err);
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
/* if the fault was due to disconnect, let khubd's
- * call to usblp_disconnect() grab usblp->sem ...
+ * call to usblp_disconnect() grab usblp->mut ...
*/
schedule ();
continue;
*/
writecount += transfer_length;
if (writecount == count) {
- up(&usblp->sem);
+ mutex_unlock(&usblp->mut);
break;
}
if (copy_from_user(usblp->writeurb->transfer_buffer,
buffer + writecount, transfer_length)) {
- up(&usblp->sem);
+ mutex_unlock(&usblp->mut);
return writecount ? writecount : -EFAULT;
}
count = -EIO;
else
count = writecount ? writecount : -ENOMEM;
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
break;
}
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
}
return count;
static ssize_t usblp_read(struct file *file, char __user *buffer, size_t count, loff_t *ppos)
{
struct usblp *usblp = file->private_data;
- int rv;
+ int rv, intr;
if (!usblp->bidir)
return -EINVAL;
- down (&usblp->sem);
+ intr = mutex_lock_interruptible (&usblp->mut);
+ if (intr)
+ return -EINTR;
if (!usblp->present) {
count = -ENODEV;
goto done;
count = -EAGAIN;
goto done;
}
- up(&usblp->sem);
+ mutex_unlock(&usblp->mut);
rv = wait_event_interruptible(usblp->wait, usblp->rcomplete || !usblp->present);
- down(&usblp->sem);
+ mutex_lock(&usblp->mut);
if (rv < 0) {
count = -EINTR;
goto done;
}
done:
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
return count;
}
goto abort;
}
usblp->dev = dev;
- init_MUTEX (&usblp->sem);
+ mutex_init (&usblp->mut);
init_waitqueue_head(&usblp->wait);
usblp->ifnum = intf->cur_altsetting->desc.bInterfaceNumber;
usblp->intf = intf;
device_remove_file(&intf->dev, &dev_attr_ieee1284_id);
mutex_lock (&usblp_mutex);
- down (&usblp->sem);
+ mutex_lock (&usblp->mut);
usblp->present = 0;
usb_set_intfdata (intf, NULL);
usblp->writebuf, usblp->writeurb->transfer_dma);
usb_buffer_free (usblp->dev, USBLP_BUF_SIZE,
usblp->readbuf, usblp->readurb->transfer_dma);
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
if (!usblp->used)
usblp_cleanup (usblp);
/* this races against normal access and open */
mutex_lock (&usblp_mutex);
- down (&usblp->sem);
+ mutex_lock (&usblp->mut);
/* we take no more IO */
usblp->sleeping = 1;
usblp_unlink_urbs(usblp);
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
mutex_unlock (&usblp_mutex);
return 0;
int r;
mutex_lock (&usblp_mutex);
- down (&usblp->sem);
+ mutex_lock (&usblp->mut);
usblp->sleeping = 0;
r = handle_bidir (usblp);
- up (&usblp->sem);
+ mutex_unlock (&usblp->mut);
mutex_unlock (&usblp_mutex);
return r;
kfree(dr);
return -EFAULT;
}
- snoop(&ps->dev->dev, "control urb\n");
+ snoop(&ps->dev->dev, "control urb: bRequest=%02x "
+ "bRrequestType=%02x wValue=%04x "
+ "wIndex=%04x wLength=%04x\n",
+ dr->bRequest, dr->bRequestType, dr->wValue,
+ dr->wIndex, dr->wLength);
break;
case USBDEVFS_URB_TYPE_BULK:
#include <linux/usb_gadget.h>
#include <asm/byteorder.h>
+#include <asm/hardware.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/system.h>
#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
#include <asm/arch/gpio.h>
#include <asm/arch/board.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/at91sam9261_matrix.h>
#include "at91_udc.h"
static const char driver_name [] = "at91_udc";
static const char ep0name[] = "ep0";
-/*-------------------------------------------------------------------------*/
-/*
- * Read from a UDP register.
- */
-static inline unsigned long at91_udp_read(unsigned int reg)
-{
- void __iomem *udp_base = (void __iomem *)AT91_VA_BASE_UDP;
-
- return __raw_readl(udp_base + reg);
-}
-
-/*
- * Write to a UDP register.
- */
-static inline void at91_udp_write(unsigned int reg, unsigned long value)
-{
- void __iomem *udp_base = (void __iomem *)AT91_VA_BASE_UDP;
-
- __raw_writel(value, udp_base + reg);
-}
+#define at91_udp_read(dev, reg) \
+ __raw_readl((dev)->udp_baseaddr + (reg))
+#define at91_udp_write(dev, reg, val) \
+ __raw_writel((val), (dev)->udp_baseaddr + (reg))
/*-------------------------------------------------------------------------*/
return 0;
}
- tmp = at91_udp_read(AT91_UDP_FRM_NUM);
+ tmp = at91_udp_read(udc, AT91_UDP_FRM_NUM);
seq_printf(s, "frame %05x:%s%s frame=%d\n", tmp,
(tmp & AT91_UDP_FRM_OK) ? " ok" : "",
(tmp & AT91_UDP_FRM_ERR) ? " err" : "",
(tmp & AT91_UDP_NUM));
- tmp = at91_udp_read(AT91_UDP_GLB_STAT);
+ tmp = at91_udp_read(udc, AT91_UDP_GLB_STAT);
seq_printf(s, "glbstate %02x:%s" FOURBITS "\n", tmp,
(tmp & AT91_UDP_RMWUPE) ? " rmwupe" : "",
(tmp & AT91_UDP_RSMINPR) ? " rsminpr" : "",
(tmp & AT91_UDP_CONFG) ? " confg" : "",
(tmp & AT91_UDP_FADDEN) ? " fadden" : "");
- tmp = at91_udp_read(AT91_UDP_FADDR);
+ tmp = at91_udp_read(udc, AT91_UDP_FADDR);
seq_printf(s, "faddr %03x:%s fadd=%d\n", tmp,
(tmp & AT91_UDP_FEN) ? " fen" : "",
(tmp & AT91_UDP_FADD));
- proc_irq_show(s, "imr ", at91_udp_read(AT91_UDP_IMR));
- proc_irq_show(s, "isr ", at91_udp_read(AT91_UDP_ISR));
+ proc_irq_show(s, "imr ", at91_udp_read(udc, AT91_UDP_IMR));
+ proc_irq_show(s, "isr ", at91_udp_read(udc, AT91_UDP_ISR));
if (udc->enabled && udc->vbus) {
proc_ep_show(s, &udc->ep[0]);
static void done(struct at91_ep *ep, struct at91_request *req, int status)
{
unsigned stopped = ep->stopped;
+ struct at91_udc *udc = ep->udc;
list_del_init(&req->queue);
if (req->req.status == -EINPROGRESS)
/* ep0 is always ready; other endpoints need a non-empty queue */
if (list_empty(&ep->queue) && ep->int_mask != (1 << 0))
- at91_udp_write(AT91_UDP_IDR, ep->int_mask);
+ at91_udp_write(udc, AT91_UDP_IDR, ep->int_mask);
}
/*-------------------------------------------------------------------------*/
* reset/init endpoint fifo. NOTE: leaves fifo_bank alone,
* since endpoint resets don't reset hw pingpong state.
*/
- at91_udp_write(AT91_UDP_RST_EP, ep->int_mask);
- at91_udp_write(AT91_UDP_RST_EP, 0);
+ at91_udp_write(dev, AT91_UDP_RST_EP, ep->int_mask);
+ at91_udp_write(dev, AT91_UDP_RST_EP, 0);
local_irq_restore(flags);
return 0;
static int at91_ep_disable (struct usb_ep * _ep)
{
struct at91_ep *ep = container_of(_ep, struct at91_ep, ep);
+ struct at91_udc *udc = ep->udc;
unsigned long flags;
if (ep == &ep->udc->ep[0])
/* reset fifos and endpoint */
if (ep->udc->clocked) {
- at91_udp_write(AT91_UDP_RST_EP, ep->int_mask);
- at91_udp_write(AT91_UDP_RST_EP, 0);
+ at91_udp_write(udc, AT91_UDP_RST_EP, ep->int_mask);
+ at91_udp_write(udc, AT91_UDP_RST_EP, 0);
__raw_writel(0, ep->creg);
}
* reconfigures the endpoints.
*/
if (dev->wait_for_config_ack) {
- tmp = at91_udp_read(AT91_UDP_GLB_STAT);
+ tmp = at91_udp_read(dev, AT91_UDP_GLB_STAT);
tmp ^= AT91_UDP_CONFG;
VDBG("toggle config\n");
- at91_udp_write(AT91_UDP_GLB_STAT, tmp);
+ at91_udp_write(dev, AT91_UDP_GLB_STAT, tmp);
}
if (req->req.length == 0) {
ep0_in_status:
if (req && !status) {
list_add_tail (&req->queue, &ep->queue);
- at91_udp_write(AT91_UDP_IER, ep->int_mask);
+ at91_udp_write(dev, AT91_UDP_IER, ep->int_mask);
}
done:
local_irq_restore(flags);
static int at91_ep_set_halt(struct usb_ep *_ep, int value)
{
struct at91_ep *ep = container_of(_ep, struct at91_ep, ep);
+ struct at91_udc *udc = ep->udc;
u32 __iomem *creg;
u32 csr;
unsigned long flags;
csr |= AT91_UDP_FORCESTALL;
VDBG("halt %s\n", ep->ep.name);
} else {
- at91_udp_write(AT91_UDP_RST_EP, ep->int_mask);
- at91_udp_write(AT91_UDP_RST_EP, 0);
+ at91_udp_write(udc, AT91_UDP_RST_EP, ep->int_mask);
+ at91_udp_write(udc, AT91_UDP_RST_EP, 0);
csr &= ~AT91_UDP_FORCESTALL;
}
__raw_writel(csr, creg);
static int at91_get_frame(struct usb_gadget *gadget)
{
+ struct at91_udc *udc = to_udc(gadget);
+
if (!to_udc(gadget)->clocked)
return -EINVAL;
- return at91_udp_read(AT91_UDP_FRM_NUM) & AT91_UDP_NUM;
+ return at91_udp_read(udc, AT91_UDP_FRM_NUM) & AT91_UDP_NUM;
}
static int at91_wakeup(struct usb_gadget *gadget)
/* NOTE: some "early versions" handle ESR differently ... */
- glbstate = at91_udp_read(AT91_UDP_GLB_STAT);
+ glbstate = at91_udp_read(udc, AT91_UDP_GLB_STAT);
if (!(glbstate & AT91_UDP_ESR))
goto done;
glbstate |= AT91_UDP_ESR;
- at91_udp_write(AT91_UDP_GLB_STAT, glbstate);
+ at91_udp_write(udc, AT91_UDP_GLB_STAT, glbstate);
done:
local_irq_restore(flags);
ep->stopped = 0;
ep->fifo_bank = 0;
ep->ep.maxpacket = ep->maxpacket;
+ ep->creg = (void __iomem *) udc->udp_baseaddr + AT91_UDP_CSR(i);
// initialiser une queue par endpoint
INIT_LIST_HEAD(&ep->queue);
}
if (!udc->enabled || !udc->vbus)
is_on = 0;
DBG("%sactive\n", is_on ? "" : "in");
+
if (is_on) {
clk_on(udc);
- at91_udp_write(AT91_UDP_TXVC, 0);
- at91_set_gpio_value(udc->board.pullup_pin, 1);
- } else {
+ at91_udp_write(udc, AT91_UDP_TXVC, 0);
+ if (cpu_is_at91rm9200())
+ at91_set_gpio_value(udc->board.pullup_pin, 1);
+ else if (cpu_is_at91sam9260()) {
+ u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC);
+
+ txvc |= AT91_UDP_TXVC_PUON;
+ at91_udp_write(udc, AT91_UDP_TXVC, txvc);
+ } else if (cpu_is_at91sam9261()) {
+ u32 usbpucr;
+
+ usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+ usbpucr |= AT91_MATRIX_USBPUCR_PUON;
+ at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+ }
+ } else {
stop_activity(udc);
- at91_udp_write(AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
- at91_set_gpio_value(udc->board.pullup_pin, 0);
+ at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
+ if (cpu_is_at91rm9200())
+ at91_set_gpio_value(udc->board.pullup_pin, 0);
+ else if (cpu_is_at91sam9260()) {
+ u32 txvc = at91_udp_read(udc, AT91_UDP_TXVC);
+
+ txvc &= ~AT91_UDP_TXVC_PUON;
+ at91_udp_write(udc, AT91_UDP_TXVC, txvc);
+ } else if (cpu_is_at91sam9261()) {
+ u32 usbpucr;
+
+ usbpucr = at91_sys_read(AT91_MATRIX_USBPUCR);
+ usbpucr &= ~AT91_MATRIX_USBPUCR_PUON;
+ at91_sys_write(AT91_MATRIX_USBPUCR, usbpucr);
+ }
clk_off(udc);
}
}
// VDBG("vbus %s\n", is_active ? "on" : "off");
local_irq_save(flags);
udc->vbus = (is_active != 0);
- pullup(udc, is_active);
+ if (udc->driver)
+ pullup(udc, is_active);
+ else
+ pullup(udc, 0);
local_irq_restore(flags);
return 0;
}
case ((USB_TYPE_STANDARD|USB_RECIP_DEVICE) << 8)
| USB_REQ_SET_CONFIGURATION:
- tmp = at91_udp_read(AT91_UDP_GLB_STAT) & AT91_UDP_CONFG;
+ tmp = at91_udp_read(udc, AT91_UDP_GLB_STAT) & AT91_UDP_CONFG;
if (pkt.r.wValue)
udc->wait_for_config_ack = (tmp == 0);
else
case ((USB_DIR_IN|USB_TYPE_STANDARD|USB_RECIP_DEVICE) << 8)
| USB_REQ_GET_STATUS:
tmp = (udc->selfpowered << USB_DEVICE_SELF_POWERED);
- if (at91_udp_read(AT91_UDP_GLB_STAT) & AT91_UDP_ESR)
+ if (at91_udp_read(udc, AT91_UDP_GLB_STAT) & AT91_UDP_ESR)
tmp |= (1 << USB_DEVICE_REMOTE_WAKEUP);
PACKET("get device status\n");
__raw_writeb(tmp, dreg);
| USB_REQ_SET_FEATURE:
if (w_value != USB_DEVICE_REMOTE_WAKEUP)
goto stall;
- tmp = at91_udp_read(AT91_UDP_GLB_STAT);
+ tmp = at91_udp_read(udc, AT91_UDP_GLB_STAT);
tmp |= AT91_UDP_ESR;
- at91_udp_write(AT91_UDP_GLB_STAT, tmp);
+ at91_udp_write(udc, AT91_UDP_GLB_STAT, tmp);
goto succeed;
case ((USB_TYPE_STANDARD|USB_RECIP_DEVICE) << 8)
| USB_REQ_CLEAR_FEATURE:
if (w_value != USB_DEVICE_REMOTE_WAKEUP)
goto stall;
- tmp = at91_udp_read(AT91_UDP_GLB_STAT);
+ tmp = at91_udp_read(udc, AT91_UDP_GLB_STAT);
tmp &= ~AT91_UDP_ESR;
- at91_udp_write(AT91_UDP_GLB_STAT, tmp);
+ at91_udp_write(udc, AT91_UDP_GLB_STAT, tmp);
goto succeed;
/*
} else if (ep->is_in)
goto stall;
- at91_udp_write(AT91_UDP_RST_EP, ep->int_mask);
- at91_udp_write(AT91_UDP_RST_EP, 0);
+ at91_udp_write(udc, AT91_UDP_RST_EP, ep->int_mask);
+ at91_udp_write(udc, AT91_UDP_RST_EP, 0);
tmp = __raw_readl(ep->creg);
tmp |= CLR_FX;
tmp &= ~(SET_FX | AT91_UDP_FORCESTALL);
#undef w_length
/* pass request up to the gadget driver */
- status = udc->driver->setup(&udc->gadget, &pkt.r);
+ if (udc->driver)
+ status = udc->driver->setup(&udc->gadget, &pkt.r);
+ else
+ status = -ENODEV;
if (status < 0) {
stall:
VDBG("req %02x.%02x protocol STALL; stat %d\n",
if (udc->wait_for_addr_ack) {
u32 tmp;
- at91_udp_write(AT91_UDP_FADDR,
+ at91_udp_write(udc, AT91_UDP_FADDR,
AT91_UDP_FEN | udc->addr);
- tmp = at91_udp_read(AT91_UDP_GLB_STAT);
+ tmp = at91_udp_read(udc, AT91_UDP_GLB_STAT);
tmp &= ~AT91_UDP_FADDEN;
if (udc->addr)
tmp |= AT91_UDP_FADDEN;
- at91_udp_write(AT91_UDP_GLB_STAT, tmp);
+ at91_udp_write(udc, AT91_UDP_GLB_STAT, tmp);
udc->wait_for_addr_ack = 0;
VDBG("address %d\n", udc->addr);
while (rescans--) {
u32 status;
- status = at91_udp_read(AT91_UDP_ISR)
- & at91_udp_read(AT91_UDP_IMR);
+ status = at91_udp_read(udc, AT91_UDP_ISR)
+ & at91_udp_read(udc, AT91_UDP_IMR);
if (!status)
break;
/* USB reset irq: not maskable */
if (status & AT91_UDP_ENDBUSRES) {
- at91_udp_write(AT91_UDP_IDR, ~MINIMUS_INTERRUPTUS);
- at91_udp_write(AT91_UDP_IER, MINIMUS_INTERRUPTUS);
+ at91_udp_write(udc, AT91_UDP_IDR, ~MINIMUS_INTERRUPTUS);
+ at91_udp_write(udc, AT91_UDP_IER, MINIMUS_INTERRUPTUS);
/* Atmel code clears this irq twice */
- at91_udp_write(AT91_UDP_ICR, AT91_UDP_ENDBUSRES);
- at91_udp_write(AT91_UDP_ICR, AT91_UDP_ENDBUSRES);
+ at91_udp_write(udc, AT91_UDP_ICR, AT91_UDP_ENDBUSRES);
+ at91_udp_write(udc, AT91_UDP_ICR, AT91_UDP_ENDBUSRES);
VDBG("end bus reset\n");
udc->addr = 0;
stop_activity(udc);
/* enable ep0 */
- at91_udp_write(AT91_UDP_CSR(0),
+ at91_udp_write(udc, AT91_UDP_CSR(0),
AT91_UDP_EPEDS | AT91_UDP_EPTYPE_CTRL);
udc->gadget.speed = USB_SPEED_FULL;
udc->suspended = 0;
- at91_udp_write(AT91_UDP_IER, AT91_UDP_EP(0));
+ at91_udp_write(udc, AT91_UDP_IER, AT91_UDP_EP(0));
/*
* NOTE: this driver keeps clocks off unless the
/* host initiated suspend (3+ms bus idle) */
} else if (status & AT91_UDP_RXSUSP) {
- at91_udp_write(AT91_UDP_IDR, AT91_UDP_RXSUSP);
- at91_udp_write(AT91_UDP_IER, AT91_UDP_RXRSM);
- at91_udp_write(AT91_UDP_ICR, AT91_UDP_RXSUSP);
+ at91_udp_write(udc, AT91_UDP_IDR, AT91_UDP_RXSUSP);
+ at91_udp_write(udc, AT91_UDP_IER, AT91_UDP_RXRSM);
+ at91_udp_write(udc, AT91_UDP_ICR, AT91_UDP_RXSUSP);
// VDBG("bus suspend\n");
if (udc->suspended)
continue;
/* host initiated resume */
} else if (status & AT91_UDP_RXRSM) {
- at91_udp_write(AT91_UDP_IDR, AT91_UDP_RXRSM);
- at91_udp_write(AT91_UDP_IER, AT91_UDP_RXSUSP);
- at91_udp_write(AT91_UDP_ICR, AT91_UDP_RXRSM);
+ at91_udp_write(udc, AT91_UDP_IDR, AT91_UDP_RXRSM);
+ at91_udp_write(udc, AT91_UDP_IER, AT91_UDP_RXSUSP);
+ at91_udp_write(udc, AT91_UDP_ICR, AT91_UDP_RXRSM);
// VDBG("bus resume\n");
if (!udc->suspended)
continue;
},
.udc = &controller,
.maxpacket = 8,
- .creg = (void __iomem *)(AT91_VA_BASE_UDP
- + AT91_UDP_CSR(0)),
.int_mask = 1 << 0,
},
.ep[1] = {
.udc = &controller,
.is_pingpong = 1,
.maxpacket = 64,
- .creg = (void __iomem *)(AT91_VA_BASE_UDP
- + AT91_UDP_CSR(1)),
.int_mask = 1 << 1,
},
.ep[2] = {
.udc = &controller,
.is_pingpong = 1,
.maxpacket = 64,
- .creg = (void __iomem *)(AT91_VA_BASE_UDP
- + AT91_UDP_CSR(2)),
.int_mask = 1 << 2,
},
.ep[3] = {
},
.udc = &controller,
.maxpacket = 8,
- .creg = (void __iomem *)(AT91_VA_BASE_UDP
- + AT91_UDP_CSR(3)),
.int_mask = 1 << 3,
},
.ep[4] = {
.udc = &controller,
.is_pingpong = 1,
.maxpacket = 256,
- .creg = (void __iomem *)(AT91_VA_BASE_UDP
- + AT91_UDP_CSR(4)),
.int_mask = 1 << 4,
},
.ep[5] = {
.udc = &controller,
.is_pingpong = 1,
.maxpacket = 256,
- .creg = (void __iomem *)(AT91_VA_BASE_UDP
- + AT91_UDP_CSR(5)),
.int_mask = 1 << 5,
},
/* ep6 and ep7 are also reserved (custom silicon might use them) */
int retval;
if (!driver
- || driver->speed != USB_SPEED_FULL
+ || driver->speed < USB_SPEED_FULL
|| !driver->bind
- || !driver->unbind
|| !driver->setup) {
DBG("bad parameter.\n");
return -EINVAL;
if (retval) {
DBG("driver->bind() returned %d\n", retval);
udc->driver = NULL;
+ udc->gadget.dev.driver = NULL;
+ udc->gadget.dev.driver_data = NULL;
+ udc->enabled = 0;
+ udc->selfpowered = 0;
return retval;
}
{
struct at91_udc *udc = &controller;
- if (!driver || driver != udc->driver)
+ if (!driver || driver != udc->driver || !driver->unbind)
return -EINVAL;
local_irq_disable();
udc->enabled = 0;
- at91_udp_write(AT91_UDP_IDR, ~0);
+ at91_udp_write(udc, AT91_UDP_IDR, ~0);
pullup(udc, 0);
local_irq_enable();
struct device *dev = &pdev->dev;
struct at91_udc *udc;
int retval;
+ struct resource *res;
if (!dev->platform_data) {
/* small (so we copy it) but critical! */
return -ENODEV;
}
- if (!request_mem_region(AT91RM9200_BASE_UDP, SZ_16K, driver_name)) {
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res)
+ return -ENXIO;
+
+ if (!request_mem_region(res->start,
+ res->end - res->start + 1,
+ driver_name)) {
DBG("someone's using UDC memory\n");
return -EBUSY;
}
udc->gadget.dev.parent = dev;
udc->board = *(struct at91_udc_data *) dev->platform_data;
udc->pdev = pdev;
- udc_reinit(udc);
udc->enabled = 0;
+ udc->udp_baseaddr = ioremap(res->start, res->end - res->start + 1);
+ if (!udc->udp_baseaddr) {
+ release_mem_region(res->start, res->end - res->start + 1);
+ return -ENOMEM;
+ }
+
+ udc_reinit(udc);
+
/* get interface and function clocks */
udc->iclk = clk_get(dev, "udc_clk");
udc->fclk = clk_get(dev, "udpck");
if (IS_ERR(udc->iclk) || IS_ERR(udc->fclk)) {
DBG("clocks missing\n");
- return -ENODEV;
+ retval = -ENODEV;
+ goto fail0;
}
retval = device_register(&udc->gadget.dev);
/* don't do anything until we have both gadget driver and VBUS */
clk_enable(udc->iclk);
- at91_udp_write(AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
- at91_udp_write(AT91_UDP_IDR, 0xffffffff);
+ at91_udp_write(udc, AT91_UDP_TXVC, AT91_UDP_TXVC_TXVDIS);
+ at91_udp_write(udc, AT91_UDP_IDR, 0xffffffff);
+ /* Clear all pending interrupts - UDP may be used by bootloader. */
+ at91_udp_write(udc, AT91_UDP_ICR, 0xffffffff);
clk_disable(udc->iclk);
/* request UDC and maybe VBUS irqs */
goto fail1;
}
if (udc->board.vbus_pin > 0) {
+ /*
+ * Get the initial state of VBUS - we cannot expect
+ * a pending interrupt.
+ */
+ udc->vbus = at91_get_gpio_value(udc->board.vbus_pin);
if (request_irq(udc->board.vbus_pin, at91_vbus_irq,
IRQF_DISABLED, driver_name, udc)) {
DBG("request vbus irq %d failed\n",
fail1:
device_unregister(&udc->gadget.dev);
fail0:
- release_mem_region(AT91RM9200_BASE_UDP, SZ_16K);
+ release_mem_region(res->start, res->end - res->start + 1);
DBG("%s probe failed, %d\n", driver_name, retval);
return retval;
}
static int __devexit at91udc_remove(struct platform_device *pdev)
{
struct at91_udc *udc = platform_get_drvdata(pdev);
+ struct resource *res;
DBG("remove\n");
- pullup(udc, 0);
+ if (udc->driver)
+ return -EBUSY;
- if (udc->driver != 0)
- usb_gadget_unregister_driver(udc->driver);
+ pullup(udc, 0);
device_init_wakeup(&pdev->dev, 0);
remove_debug_file(udc);
free_irq(udc->board.vbus_pin, udc);
free_irq(udc->udp_irq, udc);
device_unregister(&udc->gadget.dev);
- release_mem_region(AT91RM9200_BASE_UDP, SZ_16K);
+
+ iounmap(udc->udp_baseaddr);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(res->start, res->end - res->start + 1);
clk_put(udc->iclk);
clk_put(udc->fclk);
#define AT91_UDP_EP(n) (1 << (n)) /* Endpoint Interrupt Status */
#define AT91_UDP_RXSUSP (1 << 8) /* USB Suspend Interrupt Status */
#define AT91_UDP_RXRSM (1 << 9) /* USB Resume Interrupt Status */
-#define AT91_UDP_EXTRSM (1 << 10) /* External Resume Interrupt Status */
+#define AT91_UDP_EXTRSM (1 << 10) /* External Resume Interrupt Status [AT91RM9200 only] */
#define AT91_UDP_SOFINT (1 << 11) /* Start of Frame Interrupt Status */
#define AT91_UDP_ENDBUSRES (1 << 12) /* End of Bus Reset Interrpt Status */
-#define AT91_UDP_WAKEUP (1 << 13) /* USB Wakeup Interrupt Status */
+#define AT91_UDP_WAKEUP (1 << 13) /* USB Wakeup Interrupt Status [AT91RM9200 only] */
#define AT91_UDP_ICR 0x20 /* Interrupt Clear Register */
#define AT91_UDP_RST_EP 0x28 /* Reset Endpoint Register */
#define AT91_UDP_TXVC 0x74 /* Transceiver Control Register */
#define AT91_UDP_TXVC_TXVDIS (1 << 8) /* Transceiver Disable */
-
+#define AT91_UDP_TXVC_PUON (1 << 9) /* PullUp On [AT91SAM9260 only] */
/*-------------------------------------------------------------------------*/
struct clk *iclk, *fclk;
struct platform_device *pdev;
struct proc_dir_entry *pde;
+ void __iomem *udp_baseaddr;
int udp_irq;
};
return -EINVAL;
if (dum->driver)
return -EBUSY;
- if (!driver->bind || !driver->unbind || !driver->setup
+ if (!driver->bind || !driver->setup
|| driver->speed == USB_SPEED_UNKNOWN)
return -EINVAL;
err_bind_driver:
driver_unregister (&driver->driver);
err_register:
- driver->unbind (&dum->gadget);
+ if (driver->unbind)
+ driver->unbind (&dum->gadget);
spin_lock_irq (&dum->lock);
dum->pullup = 0;
set_link_state (dum);
if (!dum)
return -ENODEV;
- if (!driver || driver != dum->driver)
+ if (!driver || driver != dum->driver || !driver->unbind)
return -EINVAL;
dev_dbg (udc_dev(dum), "unregister gadget driver '%s'\n",
#endif
.function = (char *) longname,
.bind = fsg_bind,
- .unbind = __exit_p(fsg_unbind),
+ .unbind = fsg_unbind,
.disconnect = fsg_disconnect,
.setup = fsg_setup,
.suspend = fsg_suspend,
struct usb_request *req; /* for control responses */
u8 config;
struct usb_ep *in_ep, *out_ep;
- struct snd_card *card;
+ struct snd_card *card;
struct snd_rawmidi *rmidi;
struct snd_rawmidi_substream *in_substream;
struct snd_rawmidi_substream *out_substream;
int status = req->status;
switch (status) {
- case 0: /* normal completion */
+ case 0: /* normal completion */
if (ep == dev->out_ep) {
/* we received stuff.
req is queued again, below */
break;
/* this endpoint is normally active while we're configured */
- case -ECONNABORTED: /* hardware forced ep reset */
+ case -ECONNABORTED: /* hardware forced ep reset */
case -ECONNRESET: /* request dequeued */
case -ESHUTDOWN: /* disconnect from host */
VDBG(dev, "%s gone (%d), %d/%d\n", ep->name, status,
case USB_SPEED_LOW: speed = "low"; break;
case USB_SPEED_FULL: speed = "full"; break;
case USB_SPEED_HIGH: speed = "high"; break;
- default: speed = "?"; break;
+ default: speed = "?"; break;
}
dev->config = number;
.speed = USB_SPEED_FULL,
.function = (char *)longname,
.bind = gmidi_bind,
- .unbind = __exit_p(gmidi_unbind),
+ .unbind = gmidi_unbind,
.setup = gmidi_setup,
.disconnect = gmidi_disconnect,
.suspend = gmidi_suspend,
.resume = gmidi_resume,
- .driver = {
+ .driver = {
.name = (char *)shortname,
.owner = THIS_MODULE,
},
if (!driver
|| driver->speed != USB_SPEED_FULL
|| !driver->bind
- || !driver->unbind
|| !driver->disconnect
|| !driver->setup)
return -EINVAL;
if (!dev)
return -ENODEV;
- if (!driver || driver != dev->driver)
+ if (!driver || driver != dev->driver || !driver->unbind)
return -EINVAL;
spin_lock_irqsave(&dev->lock, flags);
struct goku_udc *dev = pci_get_drvdata(pdev);
DBG(dev, "%s\n", __FUNCTION__);
- /* start with the driver above us */
- if (dev->driver) {
- /* should have been done already by driver model core */
- WARN(dev, "pci remove, driver '%s' is still registered\n",
- dev->driver->driver.name);
- usb_gadget_unregister_driver(dev->driver);
- }
+
+ BUG_ON(dev->driver);
#ifdef CONFIG_USB_GADGET_DEBUG_FILES
remove_proc_entry(proc_node_name, NULL);
DEBUG("%s: %s\n", __FUNCTION__, driver->driver.name);
if (!driver
- || driver->speed != USB_SPEED_FULL
- || !driver->bind
- || !driver->unbind || !driver->disconnect || !driver->setup)
+ || driver->speed != USB_SPEED_FULL
+ || !driver->bind
+ || !driver->disconnect
+ || !driver->setup)
return -EINVAL;
if (!dev)
return -ENODEV;
if (!dev)
return -ENODEV;
- if (!driver || driver != dev->driver)
+ if (!driver || driver != dev->driver || !driver->unbind)
return -EINVAL;
spin_lock_irqsave(&dev->lock, flags);
DEBUG("%s: %p\n", __FUNCTION__, pdev);
+ if (dev->driver)
+ return -EBUSY;
+
udc_disable(dev);
remove_proc_files();
- usb_gadget_unregister_driver(dev->driver);
free_irq(IRQ_USBINTR, dev);
if (!driver
|| driver->speed != USB_SPEED_HIGH
|| !driver->bind
- || !driver->unbind
|| !driver->setup)
return -EINVAL;
if (!dev)
if (!dev)
return -ENODEV;
- if (!driver || driver != dev->driver)
+ if (!driver || driver != dev->driver || !driver->unbind)
return -EINVAL;
spin_lock_irqsave (&dev->lock, flags);
{
struct net2280 *dev = pci_get_drvdata (pdev);
- /* start with the driver above us */
- if (dev->driver) {
- /* should have been done already by driver model core */
- WARN (dev, "pci remove, driver '%s' is still registered\n",
- dev->driver->driver.name);
- usb_gadget_unregister_driver (dev->driver);
- }
+ BUG_ON(dev->driver);
/* then clean up the resources we allocated during probe() */
net2280_led_shutdown (dev);
// FIXME if otg, check: driver->is_otg
|| driver->speed < USB_SPEED_FULL
|| !driver->bind
- || !driver->unbind
|| !driver->setup)
return -EINVAL;
status = otg_set_peripheral(udc->transceiver, &udc->gadget);
if (status < 0) {
ERR("can't bind to transceiver\n");
- driver->unbind (&udc->gadget);
- udc->gadget.dev.driver = NULL;
- udc->driver = NULL;
+ if (driver->unbind) {
+ driver->unbind (&udc->gadget);
+ udc->gadget.dev.driver = NULL;
+ udc->driver = NULL;
+ }
goto done;
}
} else {
if (!udc)
return -ENODEV;
- if (!driver || driver != udc->driver)
+ if (!driver || driver != udc->driver || !driver->unbind)
return -EINVAL;
if (machine_is_omap_innovator() || machine_is_omap_osk())
if (!udc)
return -ENODEV;
+ if (udc->driver)
+ return -EBUSY;
udc->done = &done;
if (!driver
|| driver->speed < USB_SPEED_FULL
|| !driver->bind
- || !driver->unbind
|| !driver->disconnect
|| !driver->setup)
return -EINVAL;
if (!dev)
return -ENODEV;
- if (!driver || driver != dev->driver)
+ if (!driver || driver != dev->driver || !driver->unbind)
return -EINVAL;
local_irq_disable();
{
struct pxa2xx_udc *dev = platform_get_drvdata(pdev);
+ if (dev->driver)
+ return -EBUSY;
+
udc_disable(dev);
remove_proc_files();
- usb_gadget_unregister_driver(dev->driver);
if (dev->got_irq) {
free_irq(IRQ_USB, dev);
#endif /* CONFIG_USB_GADGET_DUALSPEED */
.function = GS_LONG_NAME,
.bind = gs_bind,
- .unbind = __exit_p(gs_unbind),
+ .unbind = gs_unbind,
.setup = gs_setup,
.disconnect = gs_disconnect,
.driver = {
{
struct at91_usbh_data *board = hcd->self.controller->platform_data;
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
- struct usb_device *root = hcd->self.root_hub;
int ret;
if ((ret = ohci_init(ohci)) < 0)
*/
.start = ohci_at91_start,
.stop = ohci_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
*/
.start = ohci_au1xxx_start,
.stop = ohci_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
static struct platform_driver ohci_hcd_au1xxx_driver = {
.probe = ohci_hcd_au1xxx_drv_probe,
.remove = ohci_hcd_au1xxx_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
/*.suspend = ohci_hcd_au1xxx_drv_suspend, */
/*.resume = ohci_hcd_au1xxx_drv_resume, */
.driver = {
case PIPE_CONTROL: temp = "ctrl"; break; \
case PIPE_BULK: temp = "bulk"; break; \
case PIPE_INTERRUPT: temp = "intr"; break; \
- default: temp = "isoc"; break; \
+ default: temp = "isoc"; break; \
}; temp;})
#define pipestring(pipe) edstring(usb_pipetype(pipe))
(temp & RH_PS_PSSC) ? " PSSC" : "", \
(temp & RH_PS_PESC) ? " PESC" : "", \
(temp & RH_PS_CSC) ? " CSC" : "", \
- \
+ \
(temp & RH_PS_LSDA) ? " LSDA" : "", \
(temp & RH_PS_PPS) ? " PPS" : "", \
(temp & RH_PS_PRS) ? " PRS" : "", \
(temp & RH_PS_POCI) ? " POCI" : "", \
(temp & RH_PS_PSS) ? " PSS" : "", \
- \
+ \
(temp & RH_PS_PES) ? " PES" : "", \
(temp & RH_PS_CCS) ? " CCS" : "" \
);
(info & ED_SKIP) ? " K" : "",
(ed->hwHeadP &
cpu_to_hc32(ohci, ED_H)) ?
- " H" : "");
+ " H" : "");
size -= temp;
next += temp;
static struct platform_driver ohci_hcd_ep93xx_driver = {
.probe = ohci_hcd_ep93xx_drv_probe,
.remove = ohci_hcd_ep93xx_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
#ifdef CONFIG_PM
.suspend = ohci_hcd_ep93xx_drv_suspend,
.resume = ohci_hcd_ep93xx_drv_resume,
*
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
- *
+ *
* [ Initialisation is based on Linus' ]
* [ uhci code and gregs ohci fragments ]
* [ (C) Copyright 1999 Linus Torvalds ]
* [ (C) Copyright 1999 Gregory P. Smith]
- *
- *
+ *
+ *
* OHCI is the main "non-Intel/VIA" standard for USB 1.1 host controller
* interfaces (though some non-x86 Intel chips use it). It supports
* smarter hardware than UHCI. A download link for the spec available
* through the http://www.usb.org website.
*
- * History:
- *
- * 2004/03/24 LH7A404 support (Durgesh Pattamatta & Marc Singer)
- * 2004/02/04 use generic dma_* functions instead of pci_* (dsaxena@plexity.net)
- * 2003/02/24 show registers in sysfs (Kevin Brosius)
- *
- * 2002/09/03 get rid of ed hashtables, rework periodic scheduling and
- * bandwidth accounting; if debugging, show schedules in driverfs
- * 2002/07/19 fixes to management of ED and schedule state.
- * 2002/06/09 SA-1111 support (Christopher Hoover)
- * 2002/06/01 remember frame when HC won't see EDs any more; use that info
- * to fix urb unlink races caused by interrupt latency assumptions;
- * minor ED field and function naming updates
- * 2002/01/18 package as a patch for 2.5.3; this should match the
- * 2.4.17 kernel modulo some bugs being fixed.
- *
- * 2001/10/18 merge pmac cleanup (Benjamin Herrenschmidt) and bugfixes
- * from post-2.4.5 patches.
- * 2001/09/20 URB_ZERO_PACKET support; hcca_dma portability, OPTi warning
- * 2001/09/07 match PCI PM changes, errnos from Linus' tree
- * 2001/05/05 fork 2.4.5 version into "hcd" framework, cleanup, simplify;
- * pbook pci quirks gone (please fix pbook pci sw!) (db)
- *
- * 2001/04/08 Identify version on module load (gb)
- * 2001/03/24 td/ed hashing to remove bus_to_virt (Steve Longerbeam);
- pci_map_single (db)
- * 2001/03/21 td and dev/ed allocation uses new pci_pool API (db)
- * 2001/03/07 hcca allocation uses pci_alloc_consistent (Steve Longerbeam)
- *
- * 2000/09/26 fixed races in removing the private portion of the urb
- * 2000/09/07 disable bulk and control lists when unlinking the last
- * endpoint descriptor in order to avoid unrecoverable errors on
- * the Lucent chips. (rwc@sgi)
- * 2000/08/29 use bandwidth claiming hooks (thanks Randy!), fix some
- * urb unlink probs, indentation fixes
- * 2000/08/11 various oops fixes mostly affecting iso and cleanup from
- * device unplugs.
- * 2000/06/28 use PCI hotplug framework, for better power management
- * and for Cardbus support (David Brownell)
- * 2000/earlier: fixes for NEC/Lucent chips; suspend/resume handling
- * when the controller loses power; handle UE; cleanup; ...
- *
- * v5.2 1999/12/07 URB 3rd preview,
- * v5.1 1999/11/30 URB 2nd preview, cpia, (usb-scsi)
- * v5.0 1999/11/22 URB Technical preview, Paul Mackerras powerbook susp/resume
- * i386: HUB, Keyboard, Mouse, Printer
- *
- * v4.3 1999/10/27 multiple HCs, bulk_request
- * v4.2 1999/09/05 ISO API alpha, new dev alloc, neg Error-codes
- * v4.1 1999/08/27 Randy Dunlap's - ISO API first impl.
- * v4.0 1999/08/18
- * v3.0 1999/06/25
- * v2.1 1999/05/09 code clean up
- * v2.0 1999/05/04
- * v1.0 1999/04/27 initial release
- *
* This file is licenced under the GPL.
*/
-
+
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/pci.h>
#include <linux/list.h>
#include <linux/usb.h>
#include <linux/usb/otg.h>
-#include <linux/dma-mapping.h>
+#include <linux/dma-mapping.h>
#include <linux/dmapool.h>
#include <linux/reboot.h>
int i, size = 0;
unsigned long flags;
int retval = 0;
-
+
#ifdef OHCI_VERBOSE_DEBUG
urb_print (urb, "SUB", usb_pipein (pipe));
#endif
-
+
/* every endpoint has a ed, locate and maybe (re)initialize it */
if (! (ed = ed_get (ohci, ep, urb->dev, pipe, urb->interval)))
return -ENOMEM;
memset (urb_priv, 0, sizeof (urb_priv_t) + size * sizeof (struct td *));
INIT_LIST_HEAD (&urb_priv->pending);
urb_priv->length = size;
- urb_priv->ed = ed;
+ urb_priv->ed = ed;
/* allocate the TDs (deferring hash chain updates) */
for (i = 0; i < size; i++) {
urb_free_priv (ohci, urb_priv);
return -ENOMEM;
}
- }
+ }
spin_lock_irqsave (&ohci->lock, flags);
{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
unsigned long flags;
-
+
#ifdef OHCI_VERBOSE_DEBUG
urb_print (urb, "UNLINK", 1);
-#endif
+#endif
spin_lock_irqsave (&ohci->lock, flags);
- if (HC_IS_RUNNING(hcd->state)) {
+ if (HC_IS_RUNNING(hcd->state)) {
urb_priv_t *urb_priv;
/* Unless an IRQ completed the unlink while it was being
/* Start an OHCI controller, set the BUS operational
* resets USB and controller
- * enable interrupts
+ * enable interrupts
*/
static int ohci_run (struct ohci_hcd *ohci)
{
- u32 mask, temp;
+ u32 mask, temp;
int first = ohci->fminterval == 0;
struct usb_hcd *hcd = ohci_to_hcd(ohci);
/* also: power/overcurrent flags in roothub.a */
}
- /* Reset USB nearly "by the book". RemoteWakeupConnected was
+ /* Reset USB nearly "by the book". RemoteWakeupConnected was
* saved if boot firmware (BIOS/SMM/...) told us it's connected,
* or if bus glue did the same (e.g. for PCI add-in cards with
* PCI PM support).
dl_done_list (ohci);
spin_unlock (&ohci->lock);
if (HC_IS_RUNNING(hcd->state))
- ohci_writel (ohci, OHCI_INTR_WDH, ®s->intrenable);
+ ohci_writel (ohci, OHCI_INTR_WDH, ®s->intrenable);
}
-
+
/* could track INTR_SO to reduce available PCI/... bandwidth */
/* handle any pending URB/ED unlinks, leaving INTR_SF enabled
finish_unlinks (ohci, ohci_frame_no(ohci));
if ((ints & OHCI_INTR_SF) != 0 && !ohci->ed_rm_list
&& HC_IS_RUNNING(hcd->state))
- ohci_writel (ohci, OHCI_INTR_SF, ®s->intrdisable);
+ ohci_writel (ohci, OHCI_INTR_SF, ®s->intrdisable);
spin_unlock (&ohci->lock);
if (HC_IS_RUNNING(hcd->state)) {
ohci_writel (ohci, ints, ®s->intrstatus);
- ohci_writel (ohci, OHCI_INTR_MIE, ®s->intrenable);
+ ohci_writel (ohci, OHCI_INTR_MIE, ®s->intrenable);
// flush those writes
(void) ohci_readl (ohci, &ohci->regs->control);
}
/*-------------------------------------------------------------------------*/
static void ohci_stop (struct usb_hcd *hcd)
-{
+{
struct ohci_hcd *ohci = hcd_to_ohci (hcd);
ohci_dbg (ohci, "stop %s controller (state 0x%02x)\n",
remove_debug_files (ohci);
ohci_mem_cleanup (ohci);
if (ohci->hcca) {
- dma_free_coherent (hcd->self.controller,
- sizeof *ohci->hcca,
+ dma_free_coherent (hcd->self.controller,
+ sizeof *ohci->hcca,
ohci->hcca, ohci->hcca_dma);
ohci->hcca = NULL;
ohci->hcca_dma = 0;
* recycle any "live" eds/tds (and urbs) right away.
* later, khubd disconnect processing will recycle the other state,
* (either as disconnect/reconnect, or maybe someday as a reset).
- */
+ */
spin_lock_irq(&ohci->lock);
disable (ohci);
usb_root_hub_lost_power(ohci_to_hcd(ohci)->self.root_hub);
/* empty the interrupt branches */
for (i = 0; i < NUM_INTS; i++) ohci->load [i] = 0;
for (i = 0; i < NUM_INTS; i++) ohci->hcca->int_table [i] = 0;
-
+
/* no EDs to remove */
ohci->ed_rm_list = NULL;
- /* empty control and bulk lists */
+ /* empty control and bulk lists */
ohci->ed_controltail = NULL;
ohci->ed_bulktail = NULL;
#include "ohci-au1xxx.c"
#endif
+#ifdef CONFIG_PNX8550
+#include "ohci-pnx8550.c"
+#endif
+
#ifdef CONFIG_USB_OHCI_HCD_PPC_SOC
#include "ohci-ppc-soc.c"
#endif
/*
* OHCI HCD (Host Controller Driver) for USB.
- *
+ *
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2004 David Brownell <dbrownell@users.sourceforge.net>
- *
+ *
* This file is licenced under GPL
*/
(temp & RH_PS_PSSC) ? " PSSC" : "", \
(temp & RH_PS_PESC) ? " PESC" : "", \
(temp & RH_PS_CSC) ? " CSC" : "", \
- \
+ \
(temp & RH_PS_LSDA) ? " LSDA" : "", \
(temp & RH_PS_PPS) ? " PPS" : "", \
(temp & RH_PS_PRS) ? " PRS" : "", \
(temp & RH_PS_POCI) ? " POCI" : "", \
(temp & RH_PS_PSS) ? " PSS" : "", \
- \
+ \
(temp & RH_PS_PES) ? " PES" : "", \
(temp & RH_PS_CCS) ? " CCS" : "" \
);
temp = 0;
if (rh & RH_A_NPS) /* no power switching? */
temp |= 0x0002;
- if (rh & RH_A_PSM) /* per-port power switching? */
+ if (rh & RH_A_PSM) /* per-port power switching? */
temp |= 0x0001;
if (rh & RH_A_NOCP) /* no overcurrent reporting? */
temp |= 0x0010;
#define tick_before(t1,t2) ((s16)(((s16)(t1))-((s16)(t2))) < 0)
/* called from some task, normally khubd */
-static inline void root_port_reset (struct ohci_hcd *ohci, unsigned port)
+static inline int root_port_reset (struct ohci_hcd *ohci, unsigned port)
{
__hc32 __iomem *portstat = &ohci->regs->roothub.portstatus [port];
u32 temp;
/* spin until any current reset finishes */
for (;;) {
temp = ohci_readl (ohci, portstat);
+ /* handle e.g. CardBus eject */
+ if (temp == ~(u32)0)
+ return -ESHUTDOWN;
if (!(temp & RH_PS_PRS))
break;
udelay (500);
- }
+ }
if (!(temp & RH_PS_CCS))
break;
now = ohci_readl(ohci, &ohci->regs->fmnumber);
} while (tick_before(now, reset_done));
/* caller synchronizes using PRSC */
+
+ return 0;
}
static int ohci_hub_control (
&ohci->regs->roothub.portstatus [wIndex]);
break;
case USB_PORT_FEAT_RESET:
- root_port_reset (ohci, wIndex);
+ retval = root_port_reset (ohci, wIndex);
break;
default:
goto error;
CSC_PWRCNT |= CSC_PWRCNT_USBH_EN; /* Enable clock */
udelay(1000);
USBH_CMDSTATUS = OHCI_HCR;
-
+
printk(KERN_DEBUG __FILE__
": Clock to USB host has been enabled \n");
}
retval = -EBUSY;
goto err1;
}
-
+
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
pr_debug("ioremap failed");
*/
.start = ohci_lh7a404_start,
.stop = ohci_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
static struct platform_driver ohci_hcd_lh7a404_driver = {
.probe = ohci_hcd_lh7a404_drv_probe,
.remove = ohci_hcd_lh7a404_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
/*.suspend = ohci_hcd_lh7a404_drv_suspend, */
/*.resume = ohci_hcd_lh7a404_drv_resume, */
.driver = {
/*
* OHCI HCD (Host Controller Driver) for USB.
- *
+ *
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
- *
+ *
* This file is licenced under the GPL.
*/
/*-------------------------------------------------------------------------*/
/*
- * There's basically three types of memory:
+ * OHCI deals with three types of memory:
* - data used only by the HCD ... kmalloc is fine
* - async and periodic schedules, shared by HC and HCD ... these
* need to use dma_pool or dma_alloc_coherent
* - driver buffers, read/written by HC ... the hcd glue or the
* device driver provides us with dma addresses
*
- * There's also PCI "register" data, which is memory mapped.
- * No memory seen by this driver is pagable.
+ * There's also "register" data, which is memory mapped.
+ * No memory seen by this driver (or any HCD) may be paged out.
*/
/*-------------------------------------------------------------------------*/
.reset = ohci_omap_init,
.start = ohci_omap_start,
.stop = ohci_omap_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
static struct platform_driver ohci_hcd_omap_driver = {
.probe = ohci_hcd_omap_drv_probe,
.remove = ohci_hcd_omap_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
#ifdef CONFIG_PM
.suspend = ohci_omap_suspend,
.resume = ohci_omap_resume,
*
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
- *
+ *
* [ Initialisation is based on Linus' ]
* [ uhci code and gregs ohci fragments ]
* [ (C) Copyright 1999 Linus Torvalds ]
* [ (C) Copyright 1999 Gregory P. Smith]
- *
+ *
* PCI Bus Glue
*
* This file is licenced under the GPL.
*/
-
+
#ifndef CONFIG_PCI
#error "This file is PCI bus glue. CONFIG_PCI must be defined."
#endif
pci_dev_put(b);
}
- /* Check for Compaq's ZFMicro chipset, which needs short
+ /* Check for Compaq's ZFMicro chipset, which needs short
* delays before control or bulk queues get re-activated
* in finish_unlinks()
*/
.shutdown = usb_hcd_pci_shutdown,
};
-
-static int __init ohci_hcd_pci_init (void)
+
+static int __init ohci_hcd_pci_init (void)
{
printk (KERN_DEBUG "%s: " DRIVER_INFO " (PCI)\n", hcd_name);
if (usb_disabled())
/*-------------------------------------------------------------------------*/
-static void __exit ohci_hcd_pci_cleanup (void)
-{
+static void __exit ohci_hcd_pci_cleanup (void)
+{
pci_unregister_driver (&ohci_pci_driver);
}
module_exit (ohci_hcd_pci_cleanup);
* driver for Philips PNX4008 USB Host
*
* Authors: Dmitry Chigirev <source@mvista.com>
- * Vitaly Wool <vitalywool@gmail.com>
+ * Vitaly Wool <vitalywool@gmail.com>
*
* register initialization is based on code examples provided by Philips
* Copyright (c) 2005 Koninklijke Philips Electronics N.V.
#include <asm/arch/irqs.h>
#include <asm/arch/gpio.h>
-#define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64)
+#define USB_CTRL IO_ADDRESS(PNX4008_PWRMAN_BASE + 0x64)
/* USB_CTRL bit defines */
#define USB_SLAVE_HCLK_EN (1 << 24)
--- /dev/null
+/*
+ * OHCI HCD (Host Controller Driver) for USB.
+ *
+ * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
+ * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
+ * (C) Copyright 2002 Hewlett-Packard Company
+ * (C) Copyright 2005 Embedded Alley Solutions, Inc.
+ *
+ * Bus Glue for PNX8550
+ *
+ * Written by Christopher Hoover <ch@hpl.hp.com>
+ * Based on fragments of previous driver by Russell King et al.
+ *
+ * Modified for LH7A404 from ohci-sa1111.c
+ * by Durgesh Pattamatta <pattamattad@sharpsec.com>
+ *
+ * Modified for PNX8550 from ohci-sa1111.c and sa-omap.c
+ * by Vitaly Wool <vitalywool@gmail.com>
+ *
+ * This file is licenced under the GPL.
+ */
+
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <asm/mach-pnx8550/usb.h>
+#include <asm/mach-pnx8550/int.h>
+#include <asm/mach-pnx8550/pci.h>
+
+#ifndef CONFIG_PNX8550
+#error "This file is PNX8550 bus glue. CONFIG_PNX8550 must be defined."
+#endif
+
+extern int usb_disabled(void);
+
+/*-------------------------------------------------------------------------*/
+
+static void pnx8550_start_hc(struct platform_device *dev)
+{
+ /*
+ * Set register CLK48CTL to enable and 48MHz
+ */
+ outl(0x00000003, PCI_BASE | 0x0004770c);
+
+ /*
+ * Set register CLK12CTL to enable and 48MHz
+ */
+ outl(0x00000003, PCI_BASE | 0x00047710);
+
+ udelay(100);
+}
+
+static void pnx8550_stop_hc(struct platform_device *dev)
+{
+ udelay(10);
+}
+
+
+/*-------------------------------------------------------------------------*/
+
+/* configure so an HC device and id are always provided */
+/* always called with process context; sleeping is OK */
+
+
+/**
+ * usb_hcd_pnx8550_probe - initialize pnx8550-based HCDs
+ * Context: !in_interrupt()
+ *
+ * Allocates basic resources for this USB host controller, and
+ * then invokes the start() method for the HCD associated with it
+ * through the hotplug entry's driver_data.
+ *
+ */
+int usb_hcd_pnx8550_probe (const struct hc_driver *driver,
+ struct platform_device *dev)
+{
+ int retval;
+ struct usb_hcd *hcd;
+
+ if (dev->resource[0].flags != IORESOURCE_MEM ||
+ dev->resource[1].flags != IORESOURCE_IRQ) {
+ dev_err (&dev->dev,"invalid resource type\n");
+ return -ENOMEM;
+ }
+
+ hcd = usb_create_hcd (driver, &dev->dev, "pnx8550");
+ if (!hcd)
+ return -ENOMEM;
+ hcd->rsrc_start = dev->resource[0].start;
+ hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
+
+ if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
+ dev_err(&dev->dev, "request_mem_region [0x%08llx, 0x%08llx] "
+ "failed\n", hcd->rsrc_start, hcd->rsrc_len);
+ retval = -EBUSY;
+ goto err1;
+ }
+
+ hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+ if (!hcd->regs) {
+ dev_err(&dev->dev, "ioremap [[0x%08llx, 0x%08llx] failed\n",
+ hcd->rsrc_start, hcd->rsrc_len);
+ retval = -ENOMEM;
+ goto err2;
+ }
+
+ pnx8550_start_hc(dev);
+
+ ohci_hcd_init(hcd_to_ohci(hcd));
+
+ retval = usb_add_hcd(hcd, dev->resource[1].start, SA_INTERRUPT);
+ if (retval == 0)
+ return retval;
+
+ pnx8550_stop_hc(dev);
+ iounmap(hcd->regs);
+ err2:
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+ err1:
+ usb_put_hcd(hcd);
+ return retval;
+}
+
+
+/* may be called without controller electrically present */
+/* may be called with controller, bus, and devices active */
+
+/**
+ * usb_hcd_pnx8550_remove - shutdown processing for pnx8550-based HCDs
+ * @dev: USB Host Controller being removed
+ * Context: !in_interrupt()
+ *
+ * Reverses the effect of usb_hcd_pnx8550_probe(), first invoking
+ * the HCD's stop() method. It is always called from a thread
+ * context, normally "rmmod", "apmd", or something similar.
+ *
+ */
+void usb_hcd_pnx8550_remove (struct usb_hcd *hcd, struct platform_device *dev)
+{
+ usb_remove_hcd(hcd);
+ pnx8550_stop_hc(dev);
+ iounmap(hcd->regs);
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+ usb_put_hcd(hcd);
+}
+
+/*-------------------------------------------------------------------------*/
+
+static int __devinit
+ohci_pnx8550_start (struct usb_hcd *hcd)
+{
+ struct ohci_hcd *ohci = hcd_to_ohci (hcd);
+ int ret;
+
+ ohci_dbg (ohci, "ohci_pnx8550_start, ohci:%p", ohci);
+
+ if ((ret = ohci_init(ohci)) < 0)
+ return ret;
+
+ if ((ret = ohci_run (ohci)) < 0) {
+ err ("can't start %s", hcd->self.bus_name);
+ ohci_stop (hcd);
+ return ret;
+ }
+
+ return 0;
+}
+
+/*-------------------------------------------------------------------------*/
+
+static const struct hc_driver ohci_pnx8550_hc_driver = {
+ .description = hcd_name,
+ .product_desc = "PNX8550 OHCI",
+ .hcd_priv_size = sizeof(struct ohci_hcd),
+
+ /*
+ * generic hardware linkage
+ */
+ .irq = ohci_irq,
+ .flags = HCD_USB11 | HCD_MEMORY,
+
+ /*
+ * basic lifecycle operations
+ */
+ .start = ohci_pnx8550_start,
+ .stop = ohci_stop,
+
+ /*
+ * managing i/o requests and associated device resources
+ */
+ .urb_enqueue = ohci_urb_enqueue,
+ .urb_dequeue = ohci_urb_dequeue,
+ .endpoint_disable = ohci_endpoint_disable,
+
+ /*
+ * scheduling support
+ */
+ .get_frame_number = ohci_get_frame,
+
+ /*
+ * root hub support
+ */
+ .hub_status_data = ohci_hub_status_data,
+ .hub_control = ohci_hub_control,
+ .hub_irq_enable = ohci_rhsc_enable,
+#ifdef CONFIG_PM
+ .bus_suspend = ohci_bus_suspend,
+ .bus_resume = ohci_bus_resume,
+#endif
+ .start_port_reset = ohci_start_port_reset,
+};
+
+/*-------------------------------------------------------------------------*/
+
+static int ohci_hcd_pnx8550_drv_probe(struct platform_device *pdev)
+{
+ int ret;
+
+ if (usb_disabled())
+ return -ENODEV;
+
+ ret = usb_hcd_pnx8550_probe(&ohci_pnx8550_hc_driver, pdev);
+ return ret;
+}
+
+static int ohci_hcd_pnx8550_drv_remove(struct platform_device *pdev)
+{
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
+ usb_hcd_pnx8550_remove(hcd, pdev);
+ return 0;
+}
+
+MODULE_ALIAS("pnx8550-ohci");
+
+static struct platform_driver ohci_hcd_pnx8550_driver = {
+ .driver = {
+ .name = "pnx8550-ohci",
+ },
+ .probe = ohci_hcd_pnx8550_drv_probe,
+ .remove = ohci_hcd_pnx8550_drv_remove,
+};
+
+static int __init ohci_hcd_pnx8550_init (void)
+{
+ pr_debug (DRIVER_INFO " (pnx8550)");
+ pr_debug ("block sizes: ed %d td %d\n",
+ sizeof (struct ed), sizeof (struct td));
+
+ return platform_driver_register(&ohci_hcd_pnx8550_driver);
+}
+
+static void __exit ohci_hcd_pnx8550_cleanup (void)
+{
+ platform_driver_unregister(&ohci_hcd_pnx8550_driver);
+}
+
+module_init (ohci_hcd_pnx8550_init);
+module_exit (ohci_hcd_pnx8550_cleanup);
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
* (C) Copyright 2002 Hewlett-Packard Company
* (C) Copyright 2003-2005 MontaVista Software Inc.
- *
+ *
* Bus Glue for PPC On-Chip OHCI driver
* Tested on Freescale MPC5200 and IBM STB04xxx
*
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err1:
- usb_put_hcd(hcd);
+ usb_put_hcd(hcd);
return retval;
}
*/
.start = ohci_ppc_soc_start,
.stop = ohci_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
static struct platform_driver ohci_hcd_ppc_soc_driver = {
.probe = ohci_hcd_ppc_soc_drv_probe,
.remove = ohci_hcd_ppc_soc_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
#ifdef CONFIG_PM
/*.suspend = ohci_hcd_ppc_soc_drv_suspend,*/
/*.resume = ohci_hcd_ppc_soc_drv_resume,*/
switch ( mode ) {
case PMM_NPS_MODE:
UHCRHDA |= RH_A_NPS;
- break;
+ break;
case PMM_GLOBAL_MODE:
UHCRHDA &= ~(RH_A_NPS & RH_A_PSM);
break;
break;
default:
printk( KERN_ERR
- "Invalid mode %d, set to non-power switch mode.\n",
+ "Invalid mode %d, set to non-power switch mode.\n",
mode );
UHCRHDA |= RH_A_NPS;
*/
.start = ohci_pxa27x_start,
.stop = ohci_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
static struct platform_driver ohci_hcd_pxa27x_driver = {
.probe = ohci_hcd_pxa27x_drv_probe,
.remove = ohci_hcd_pxa27x_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
#ifdef CONFIG_PM
- .suspend = ohci_hcd_pxa27x_drv_suspend,
+ .suspend = ohci_hcd_pxa27x_drv_suspend,
.resume = ohci_hcd_pxa27x_drv_resume,
#endif
.driver = {
/*
* OHCI HCD (Host Controller Driver) for USB.
- *
+ *
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
- *
+ *
* This file is licenced under the GPL.
*/
/*-------------------------------------------------------------------------*
* ED handling functions
- *-------------------------------------------------------------------------*/
+ *-------------------------------------------------------------------------*/
/* search for the right schedule branch to use for a periodic ed.
* does some load balancing; returns the branch, or negative errno.
*/
for (i = 0; i < interval ; i++) {
if (branch < 0 || ohci->load [branch] > ohci->load [i]) {
-#if 1 /* CONFIG_USB_BANDWIDTH */
int j;
/* usb 1.1 says 90% of one frame */
}
if (j < NUM_INTS)
continue;
-#endif
- branch = i;
+ branch = i;
}
}
return branch;
/* link an ed into one of the HC chains */
static int ed_schedule (struct ohci_hcd *ohci, struct ed *ed)
-{
+{
int branch;
if (ohci_to_hcd(ohci)->state == HC_STATE_QUIESCING)
}
ed->branch = branch;
periodic_link (ohci, ed);
- }
+ }
/* the HC may not see the schedule updates yet, but if it does
* then they'll be properly ordered.
*prev = ed->ed_next;
}
ohci->load [i] -= ed->load;
- }
+ }
ohci_to_hcd(ohci)->self.bandwidth_allocated -= ed->load / ed->interval;
ohci_vdbg (ohci, "unlink %sed %p branch %d [%dus.], interval %d\n",
ed, ed->branch, ed->load, ed->interval);
}
-/* unlink an ed from one of the HC chains.
+/* unlink an ed from one of the HC chains.
* just the link to the ed is unlinked.
* the link from the ed still points to another operational ed or 0
* so the HC can eventually finish the processing of the unlinked ed
* When finish_unlinks() runs later, after SOF interrupt, it will often
* complete one or more URB unlinks before making that state change.
*/
-static void ed_deschedule (struct ohci_hcd *ohci, struct ed *ed)
+static void ed_deschedule (struct ohci_hcd *ohci, struct ed *ed)
{
ed->hwINFO |= cpu_to_hc32 (ohci, ED_SKIP);
wmb ();
unsigned int pipe,
int interval
) {
- struct ed *ed;
+ struct ed *ed;
unsigned long flags;
spin_lock_irqsave (&ohci->lock, flags);
goto done;
}
- /* dummy td; end of td list for ed */
+ /* dummy td; end of td list for ed */
td = td_alloc (ohci, GFP_ATOMIC);
- if (!td) {
+ if (!td) {
/* out of memory */
ed_free (ohci, ed);
ed = NULL;
done:
spin_unlock_irqrestore (&ohci->lock, flags);
- return ed;
+ return ed;
}
/*-------------------------------------------------------------------------*/
* and that ed->state is ED_OPER
*/
static void start_ed_unlink (struct ohci_hcd *ohci, struct ed *ed)
-{
+{
ed->hwINFO |= cpu_to_hc32 (ohci, ED_DEQUEUE);
ed_deschedule (ohci, ed);
td->ed = urb_priv->ed;
td->next_dl_td = NULL;
td->index = index;
- td->urb = urb;
+ td->urb = urb;
td->data_dma = data;
if (!len)
data = 0;
(data & 0x0FFF) | 0xE000);
td->ed->last_iso = info & 0xffff;
} else {
- td->hwCBP = cpu_to_hc32 (ohci, data);
- }
+ td->hwCBP = cpu_to_hc32 (ohci, data);
+ }
if (data)
td->hwBE = cpu_to_hc32 (ohci, data + len - 1);
else
* use the device toggle bits for resetting, and rely on the fact
* that resetting toggle is meaningless if the endpoint is active.
*/
- if (!usb_gettoggle (urb->dev, usb_pipeendpoint (urb->pipe), is_out)) {
+ if (!usb_gettoggle (urb->dev, usb_pipeendpoint (urb->pipe), is_out)) {
usb_settoggle (urb->dev, usb_pipeendpoint (urb->pipe),
is_out, 1);
urb_priv->ed->hwHeadP &= ~cpu_to_hc32 (ohci, ED_C);
list_del (&td->td_list);
/* ISO ... drivers see per-TD length/status */
- if (tdINFO & TD_ISO) {
- u16 tdPSW = ohci_hwPSW (ohci, td, 0);
+ if (tdINFO & TD_ISO) {
+ u16 tdPSW = ohci_hwPSW (ohci, td, 0);
int dlen = 0;
/* NOTE: assumes FC in tdINFO == 0, and that
* only the first of 0..MAXPSW psws is used.
*/
- cc = (tdPSW >> 12) & 0xF;
- if (tdINFO & TD_CC) /* hc didn't touch? */
+ cc = (tdPSW >> 12) & 0xF;
+ if (tdINFO & TD_CC) /* hc didn't touch? */
return;
if (usb_pipeout (urb->pipe))
int type = usb_pipetype (urb->pipe);
u32 tdBE = hc32_to_cpup (ohci, &td->hwBE);
- cc = TD_CC_GET (tdINFO);
+ cc = TD_CC_GET (tdINFO);
/* update packet status if needed (short is normally ok) */
if (cc == TD_DATAUNDERRUN
urb, td, 1 + td->index, cc,
urb->actual_length,
urb->transfer_buffer_length);
- }
+ }
}
/*-------------------------------------------------------------------------*/
static inline struct td *
ed_halted (struct ohci_hcd *ohci, struct td *td, int cc, struct td *rev)
{
- struct urb *urb = td->urb;
+ struct urb *urb = td->urb;
struct ed *ed = td->ed;
struct list_head *tmp = td->td_list.next;
__hc32 toggle = ed->hwHeadP & cpu_to_hc32 (ohci, ED_C);
*/
ed->hwINFO |= cpu_to_hc32 (ohci, ED_SKIP);
wmb ();
- ed->hwHeadP &= ~cpu_to_hc32 (ohci, ED_H);
+ ed->hwHeadP &= ~cpu_to_hc32 (ohci, ED_H);
/* put any later tds from this urb onto the donelist, after 'td',
* order won't matter here: no errors, and nothing was transferred.
info &= ~cpu_to_hc32 (ohci, TD_CC);
next->hwINFO = info;
- next->next_dl_td = rev;
+ next->next_dl_td = rev;
rev = next;
ed->hwHeadP = next->hwNextTD | toggle;
/* get TD from hc's singly linked list, and
* prepend to ours. ed->td_list changes later.
*/
- while (td_dma) {
- int cc;
+ while (td_dma) {
+ int cc;
td = dma_to_td (ohci, td_dma);
if (!td) {
&& (td->ed->hwHeadP & cpu_to_hc32 (ohci, ED_H)))
td_rev = ed_halted (ohci, td, cc, td_rev);
- td->next_dl_td = td_rev;
+ td->next_dl_td = td_rev;
td_rev = td;
td_dma = hc32_to_cpup (ohci, &td->hwNextTD);
- }
+ }
return td_rev;
}
if (modified)
goto rescan_all;
- }
+ }
- /* maybe reenable control and bulk lists */
+ /* maybe reenable control and bulk lists */
if (HC_IS_RUNNING(ohci_to_hcd(ohci)->state)
&& ohci_to_hcd(ohci)->state != HC_STATE_QUIESCING
&& !ohci->ed_rm_list) {
&ohci->regs->ed_bulkcurrent);
}
}
-
+
/* CLE/BLE to enable, CLF/BLF to (maybe) kickstart */
if (control) {
ohci->hc_control |= control;
if (ohci->flags & OHCI_QUIRK_ZFMICRO)
mdelay(1);
- ohci_writel (ohci, ohci->hc_control,
- &ohci->regs->control);
- }
+ ohci_writel (ohci, ohci->hc_control,
+ &ohci->regs->control);
+ }
if (command) {
if (ohci->flags & OHCI_QUIRK_ZFMICRO)
mdelay(1);
- ohci_writel (ohci, command, &ohci->regs->cmdstatus);
- }
+ ohci_writel (ohci, command, &ohci->regs->cmdstatus);
+ }
}
}
{
struct td *td = dl_reverse_done_list (ohci);
- while (td) {
+ while (td) {
struct td *td_next = td->next_dl_td;
struct urb *urb = td->urb;
urb_priv_t *urb_priv = urb->hcpriv;
struct ed *ed = td->ed;
/* update URB's length and status from TD */
- td_done (ohci, urb, td);
- urb_priv->td_cnt++;
+ td_done (ohci, urb, td);
+ urb_priv->td_cnt++;
/* If all this urb's TDs are done, call complete() */
- if (urb_priv->td_cnt == urb_priv->length)
- finish_urb (ohci, urb);
+ if (urb_priv->td_cnt == urb_priv->length)
+ finish_urb (ohci, urb);
/* clean schedule: unlink EDs that are no longer busy */
if (list_empty (&ed->td_list)) {
start_ed_unlink (ohci, ed);
/* ... reenabling halted EDs only after fault cleanup */
- } else if ((ed->hwINFO & cpu_to_hc32 (ohci, ED_SKIP | ED_DEQUEUE))
+ } else if ((ed->hwINFO & cpu_to_hc32 (ohci,
+ ED_SKIP | ED_DEQUEUE))
== cpu_to_hc32 (ohci, ED_SKIP)) {
td = list_entry (ed->td_list.next, struct td, td_list);
- if (!(td->hwINFO & cpu_to_hc32 (ohci, TD_DONE))) {
+ if (!(td->hwINFO & cpu_to_hc32 (ohci, TD_DONE))) {
ed->hwINFO &= ~cpu_to_hc32 (ohci, ED_SKIP);
/* ... hc may need waking-up */
switch (ed->type) {
case PIPE_CONTROL:
ohci_writel (ohci, OHCI_CLF,
- &ohci->regs->cmdstatus);
+ &ohci->regs->cmdstatus);
break;
case PIPE_BULK:
ohci_writel (ohci, OHCI_BLF,
- &ohci->regs->cmdstatus);
+ &ohci->regs->cmdstatus);
break;
}
}
}
- td = td_next;
- }
+ td = td_next;
+ }
}
*/
.start = ohci_s3c2410_start,
.stop = ohci_stop,
- .shutdown = ohci_shutdown,
+ .shutdown = ohci_shutdown,
/*
* managing i/o requests and associated device resources
static struct platform_driver ohci_hcd_s3c2410_driver = {
.probe = ohci_hcd_s3c2410_drv_probe,
.remove = ohci_hcd_s3c2410_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .shutdown = usb_hcd_platform_shutdown,
/*.suspend = ohci_hcd_s3c2410_drv_suspend, */
/*.resume = ohci_hcd_s3c2410_drv_resume, */
.driver = {
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
* (C) Copyright 2002 Hewlett-Packard Company
- *
+ *
* SA1111 Bus Glue
*
* Written by Christopher Hoover <ch@hpl.hp.com>
*
* This file is licenced under the GPL.
*/
-
+
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/assabet.h>
{
unsigned int usb_rst = 0;
- printk(KERN_DEBUG __FILE__
+ printk(KERN_DEBUG __FILE__
": starting SA-1111 OHCI USB Controller\n");
#ifdef CONFIG_SA1100_BADGE4
static void sa1111_stop_hc(struct sa1111_dev *dev)
{
unsigned int usb_rst;
- printk(KERN_DEBUG __FILE__
+ printk(KERN_DEBUG __FILE__
": stopping SA-1111 OHCI USB Controller\n");
/*
/*
* OHCI HCD (Host Controller Driver) for USB.
- *
+ *
* (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at>
* (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net>
- *
+ *
* This file is licenced under the GPL.
*/
*/
typedef __u32 __bitwise __hc32;
typedef __u16 __bitwise __hc16;
-
+
/*
* OHCI Endpoint Descriptor (ED) ... holds TD queue
* See OHCI spec, section 4.2
*/
struct ed {
/* first fields are hardware-specified */
- __hc32 hwINFO; /* endpoint config bitmap */
+ __hc32 hwINFO; /* endpoint config bitmap */
/* info bits defined by hcd */
#define ED_DEQUEUE (1 << 27)
/* info bits defined by the hardware */
* usually: OPER --> UNLINK --> (IDLE | OPER) --> ...
*/
u8 state; /* ED_{IDLE,UNLINK,OPER} */
-#define ED_IDLE 0x00 /* NOT linked to HC */
-#define ED_UNLINK 0x01 /* being unlinked from hc */
+#define ED_IDLE 0x00 /* NOT linked to HC */
+#define ED_UNLINK 0x01 /* being unlinked from hc */
#define ED_OPER 0x02 /* IS linked to hc */
- u8 type; /* PIPE_{BULK,...} */
+ u8 type; /* PIPE_{BULK,...} */
/* periodic scheduling params (for intr and iso) */
u8 branch;
#define ED_MASK ((u32)~0x0f) /* strip hw status in low addr bits */
-
+
/*
* OHCI Transfer Descriptor (TD) ... one per transfer segment
* See OHCI spec, sections 4.3.1 (general = control/bulk/interrupt)
/* (no hwINFO #defines yet for iso tds) */
- __hc32 hwCBP; /* Current Buffer Pointer (or 0) */
- __hc32 hwNextTD; /* Next TD Pointer */
- __hc32 hwBE; /* Memory Buffer End Pointer */
+ __hc32 hwCBP; /* Current Buffer Pointer (or 0) */
+ __hc32 hwNextTD; /* Next TD Pointer */
+ __hc32 hwBE; /* Memory Buffer End Pointer */
/* PSW is only for ISO. Only 1 PSW entry is used, but on
* big-endian PPC hardware that's the second entry.
*/
#define MAXPSW 2
- __hc16 hwPSW [MAXPSW];
+ __hc16 hwPSW [MAXPSW];
/* rest are purely for the driver's use */
- __u8 index;
- struct ed *ed;
- struct td *td_hash; /* dma-->td hashtable */
- struct td *next_dl_td;
- struct urb *urb;
+ __u8 index;
+ struct ed *ed;
+ struct td *td_hash; /* dma-->td hashtable */
+ struct td *next_dl_td;
+ struct urb *urb;
dma_addr_t td_dma; /* addr of this TD */
dma_addr_t data_dma; /* addr of data it points to */
#define TD_NOTACCESSED 0x0F
-/* map OHCI TD status codes (CC) to errno values */
-static const int cc_to_error [16] = {
+/* map OHCI TD status codes (CC) to errno values */
+static const int cc_to_error [16] = {
/* No Error */ 0,
/* CRC Error */ -EILSEQ,
/* Bit Stuff */ -EPROTO,
/* BufferOver */ -ECOMM,
/* BuffUnder */ -ENOSR,
/* (for HCD) */ -EALREADY,
- /* (for HCD) */ -EALREADY
+ /* (for HCD) */ -EALREADY
};
#define NUM_INTS 32
__hc32 int_table [NUM_INTS]; /* periodic schedule */
- /*
+ /*
* OHCI defines u16 frame_no, followed by u16 zero pad.
* Since some processors can't do 16 bit bus accesses,
* portable access must be a 32 bits wide.
* HcCommandStatus (cmdstatus) register masks
*/
#define OHCI_HCR (1 << 0) /* host controller reset */
-#define OHCI_CLF (1 << 1) /* control list filled */
-#define OHCI_BLF (1 << 2) /* bulk list filled */
-#define OHCI_OCR (1 << 3) /* ownership change request */
-#define OHCI_SOC (3 << 16) /* scheduling overrun count */
+#define OHCI_CLF (1 << 1) /* control list filled */
+#define OHCI_BLF (1 << 2) /* bulk list filled */
+#define OHCI_OCR (1 << 3) /* ownership change request */
+#define OHCI_SOC (3 << 16) /* scheduling overrun count */
/*
* masks used with interrupt registers:
/* OHCI ROOT HUB REGISTER MASKS */
-
+
/* roothub.portstatus [i] bits */
-#define RH_PS_CCS 0x00000001 /* current connect status */
-#define RH_PS_PES 0x00000002 /* port enable status*/
-#define RH_PS_PSS 0x00000004 /* port suspend status */
-#define RH_PS_POCI 0x00000008 /* port over current indicator */
-#define RH_PS_PRS 0x00000010 /* port reset status */
-#define RH_PS_PPS 0x00000100 /* port power status */
-#define RH_PS_LSDA 0x00000200 /* low speed device attached */
-#define RH_PS_CSC 0x00010000 /* connect status change */
-#define RH_PS_PESC 0x00020000 /* port enable status change */
-#define RH_PS_PSSC 0x00040000 /* port suspend status change */
-#define RH_PS_OCIC 0x00080000 /* over current indicator change */
-#define RH_PS_PRSC 0x00100000 /* port reset status change */
+#define RH_PS_CCS 0x00000001 /* current connect status */
+#define RH_PS_PES 0x00000002 /* port enable status*/
+#define RH_PS_PSS 0x00000004 /* port suspend status */
+#define RH_PS_POCI 0x00000008 /* port over current indicator */
+#define RH_PS_PRS 0x00000010 /* port reset status */
+#define RH_PS_PPS 0x00000100 /* port power status */
+#define RH_PS_LSDA 0x00000200 /* low speed device attached */
+#define RH_PS_CSC 0x00010000 /* connect status change */
+#define RH_PS_PESC 0x00020000 /* port enable status change */
+#define RH_PS_PSSC 0x00040000 /* port suspend status change */
+#define RH_PS_OCIC 0x00080000 /* over current indicator change */
+#define RH_PS_PRSC 0x00100000 /* port reset status change */
/* roothub.status bits */
#define RH_HS_LPS 0x00000001 /* local power status */
} urb_priv_t;
#define TD_HASH_SIZE 64 /* power'o'two */
-// sizeof (struct td) ~= 64 == 2^6 ...
+// sizeof (struct td) ~= 64 == 2^6 ...
#define TD_HASH_FUNC(td_dma) ((td_dma ^ (td_dma >> 6)) % TD_HASH_SIZE)
struct ed *ed_bulktail; /* last in bulk list */
struct ed *ed_controltail; /* last in ctrl list */
- struct ed *periodic [NUM_INTS]; /* shadow int_table */
+ struct ed *periodic [NUM_INTS]; /* shadow int_table */
/*
* OTG controllers and transceivers need software interaction;
- * other external transceivers should be software-transparent
+ * other external transceivers should be software-transparent
*/
struct otg_transceiver *transceiver;
*/
int num_ports;
int load [NUM_INTS];
- u32 hc_control; /* copy of hc control reg */
+ u32 hc_control; /* copy of hc control reg */
unsigned long next_statechange; /* suspend/resume */
u32 fminterval; /* saved register */
unsigned autostop:1; /* rh auto stopping/stopped */
}
#define FI 0x2edf /* 12000 bits per frame (-1) */
-#define FSMP(fi) (0x7fff & ((6 * ((fi) - 210)) / 7))
+#define FSMP(fi) (0x7fff & ((6 * ((fi) - 210)) / 7))
#define FIT (1 << 31)
#define LSTHRESH 0x628 /* lowspeed bit threshold */
-static void periodic_reinit (struct ohci_hcd *ohci)
+static inline void periodic_reinit (struct ohci_hcd *ohci)
{
u32 fi = ohci->fminterval & 0x03fff;
u32 fit = ohci_readl(ohci, &ohci->regs->fminterval) & FIT;
temp = ohci_readl (hc, &hc->regs->roothub.register); \
temp; })
-static u32 roothub_a (struct ohci_hcd *hc)
+static inline u32 roothub_a (struct ohci_hcd *hc)
{ return read_roothub (hc, a, 0xfc0fe000); }
static inline u32 roothub_b (struct ohci_hcd *hc)
{ return ohci_readl (hc, &hc->regs->roothub.b); }
static inline u32 roothub_status (struct ohci_hcd *hc)
{ return ohci_readl (hc, &hc->regs->roothub.status); }
-static u32 roothub_portstatus (struct ohci_hcd *hc, int i)
+static inline u32 roothub_portstatus (struct ohci_hcd *hc, int i)
{ return read_roothub (hc, portstatus [i], 0xffe0fce0); }
#include <linux/moduleparam.h>
#include <linux/delay.h>
#include <linux/ioport.h>
+#include <linux/pci_ids.h>
#include <linux/sched.h>
#include <linux/slab.h>
#include <linux/smp_lock.h>
* these cannot be inlines because we need the structure offset!!
* Does anyone have a better way?????
*/
+#define ftdi_read_pcimem(pdev, member, data) usb_ftdi_elan_read_pcimem(pdev, \
+ offsetof(struct ohci_regs, member), 0, data);
+#define ftdi_write_pcimem(pdev, member, data) usb_ftdi_elan_write_pcimem(pdev, \
+ offsetof(struct ohci_regs, member), 0, data);
#define u132_read_pcimem(u132, member, data) \
usb_ftdi_elan_read_pcimem(u132->platform_dev, offsetof(struct \
ohci_regs, member), 0, data);
#define u132_write_pcimem(u132, member, data) \
usb_ftdi_elan_write_pcimem(u132->platform_dev, offsetof(struct \
ohci_regs, member), 0, data);
-#define u132_write_pcimem_byte(u132, member, data) \
- usb_ftdi_elan_write_pcimem(u132->platform_dev, offsetof(struct \
- ohci_regs, member), 0x0e, data);
static inline struct u132 *udev_to_u132(struct u132_udev *udev)
{
u8 udev_number = udev->udev_number;
return "?";
}
-static int u132_usb_reset(struct u132 *u132)
-{
- int retval;
- retval = u132_read_pcimem(u132, control, &u132->hc_control);
- if (retval)
- return retval;
- u132->hc_control &= OHCI_CTRL_RWC;
- retval = u132_write_pcimem(u132, control, u132->hc_control);
- if (retval)
- return retval;
- return 0;
-}
-
static int u132_init(struct u132 *u132)
{
int retval;
u32 control;
u132_disable(u132);
- u132->next_statechange =
- jiffies; /* SMM owns the HC? not for long! */ {
- u32 control;
- retval = u132_read_pcimem(u132, control, &control);
- if (retval)
- return retval;
- if (control & OHCI_CTRL_IR) {
- u32 temp = 50;
- retval = u132_write_pcimem(u132, intrenable,
- OHCI_INTR_OC);
- if (retval)
- return retval;
- retval = u132_write_pcimem_byte(u132, cmdstatus,
- OHCI_OCR);
- if (retval)
- return retval;
- check:{
- retval = u132_read_pcimem(u132, control,
- &control);
- if (retval)
- return retval;
- }
- if (control & OHCI_CTRL_IR) {
- msleep(10);
- if (--temp == 0) {
- dev_err(&u132->platform_dev->dev, "USB "
- "HC takeover failed!(BIOS/SMM b"
- "ug) control=%08X\n", control);
- return -EBUSY;
- }
- goto check;
- }
- u132_usb_reset(u132);
- }
- }
+ u132->next_statechange = jiffies;
retval = u132_write_pcimem(u132, intrdisable, OHCI_INTR_MIE);
if (retval)
return retval;
retry:retval = u132_read_pcimem(u132, cmdstatus, &status);
if (retval)
return retval;
- retval = u132_write_pcimem_byte(u132, cmdstatus, OHCI_HCR);
+ retval = u132_write_pcimem(u132, cmdstatus, OHCI_HCR);
if (retval)
return retval;
extra:{
retval = u132_write_pcimem(u132, control, u132->hc_control);
if (retval)
return retval;
- retval = u132_write_pcimem_byte(u132, cmdstatus, OHCI_BLF);
+ retval = u132_write_pcimem(u132, cmdstatus, OHCI_BLF);
if (retval)
return retval;
retval = u132_read_pcimem(u132, cmdstatus, &cmdstatus);
{
struct u132 *u132 = hcd_to_u132(hcd);
if (u132->going > 1) {
- dev_err(&u132->platform_dev->dev, "device has been removed %d\n"
- , u132->going);
+ dev_err(&u132->platform_dev->dev, "u132 device %p(hcd=%p) has b"
+ "een removed %d\n", u132, hcd, u132->going);
} else if (u132->going > 0) {
dev_err(&u132->platform_dev->dev, "device hcd=%p is being remov"
"ed\n", hcd);
{
struct u132 *u132 = hcd_to_u132(hcd);
if (u132->going > 2) {
- dev_err(&u132->platform_dev->dev, "device has been removed %d\n"
- , u132->going);
+ dev_err(&u132->platform_dev->dev, "u132 device %p(hcd=%p hep=%p"
+ ") has been removed %d\n", u132, hcd, hep,
+ u132->going);
} else {
struct u132_endp *endp = hep->hcpriv;
if (endp)
} else if (u132->going > 0) {
dev_err(&u132->platform_dev->dev, "device hcd=%p is being remov"
"ed\n", hcd);
- dump_stack();
return -ESHUTDOWN;
} else {
int i, changed = 0, length = 1;
struct usb_hcd *hcd = platform_get_drvdata(pdev);
if (hcd) {
struct u132 *u132 = hcd_to_u132(hcd);
- dump_stack();
if (u132->going++ > 1) {
+ dev_err(&u132->platform_dev->dev, "already being remove"
+ "d\n");
return -ENODEV;
} else {
int rings = MAX_U132_RINGS;
int endps = MAX_U132_ENDPS;
+ dev_err(&u132->platform_dev->dev, "removing device u132"
+ ".%d\n", u132->sequence_num);
msleep(100);
down(&u132->sw_lock);
u132_monitor_cancel_work(u132);
static int __devinit u132_probe(struct platform_device *pdev)
{
struct usb_hcd *hcd;
+ int retval;
+ u32 control;
+ u32 rh_a = -1;
+ u32 num_ports;
msleep(100);
if (u132_exiting > 0) {
return -ENODEV;
- } /* refuse to confuse usbcore */
+ }
+ retval = ftdi_write_pcimem(pdev, intrdisable, OHCI_INTR_MIE);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(pdev, control, &control);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(pdev, roothub.a, &rh_a);
+ if (retval)
+ return retval;
+ num_ports = rh_a & RH_A_NDP; /* refuse to confuse usbcore */
if (pdev->dev.dma_mask) {
return -EINVAL;
}
Alan Stern"
#define DRIVER_DESC "USB Universal Host Controller Interface driver"
+/* for flakey hardware, ignore overcurrent indicators */
+static int ignore_oc;
+module_param(ignore_oc, bool, S_IRUGO);
+MODULE_PARM_DESC(ignore_oc, "ignore hardware overcurrent indications");
+
/*
* debug = 0, no debugging messages
* debug = 1, dump failed URBs except for stalls
{
int port;
+ /* If we have to ignore overcurrent events then almost by definition
+ * we can't depend on resume-detect interrupts. */
+ if (ignore_oc)
+ return 1;
+
switch (to_pci_dev(uhci_dev(uhci))->vendor) {
default:
break;
{
int retval = -ENOMEM;
- printk(KERN_INFO DRIVER_DESC " " DRIVER_VERSION "\n");
+ printk(KERN_INFO DRIVER_DESC " " DRIVER_VERSION "%s\n",
+ ignore_oc ? ", overcurrent ignored" : "");
if (usb_disabled())
return -ENODEV;
static inline int get_hub_status_data(struct uhci_hcd *uhci, char *buf)
{
int port;
+ int mask = RWC_BITS;
+
+ /* Some boards (both VIA and Intel apparently) report bogus
+ * overcurrent indications, causing massive log spam unless
+ * we completely ignore them. This doesn't seem to be a problem
+ * with the chipset so much as with the way it is connected on
+ * the motherboard; if the overcurrent input is left to float
+ * then it may constantly register false positives. */
+ if (ignore_oc)
+ mask &= ~USBPORTSC_OCC;
*buf = 0;
for (port = 0; port < uhci->rh_numports; ++port) {
- if ((inw(uhci->io_addr + USBPORTSC1 + port * 2) & RWC_BITS) ||
+ if ((inw(uhci->io_addr + USBPORTSC1 + port * 2) & mask) ||
test_bit(port, &uhci->port_c_suspend))
*buf |= (1 << (port + 1));
}
wPortChange |= USB_PORT_STAT_C_CONNECTION;
if (status & USBPORTSC_PEC)
wPortChange |= USB_PORT_STAT_C_ENABLE;
- if (status & USBPORTSC_OCC)
+ if ((status & USBPORTSC_OCC) && !ignore_oc)
wPortChange |= USB_PORT_STAT_C_OVERCURRENT;
if (test_bit(port, &uhci->port_c_suspend)) {
{
input_dev->keybit[LONG(BTN_DIGI)] |= BIT(BTN_TOOL_FINGER);
input_dev->keybit[LONG(BTN_LEFT)] |= BIT(BTN_0) | BIT(BTN_1) | BIT(BTN_2) | BIT(BTN_3);
- input_set_abs_params(input_dev, ABS_RX, 0, 4097, 0, 0);
+ input_set_abs_params(input_dev, ABS_RX, 0, 4096, 0, 0);
}
void input_dev_i3(struct input_dev *input_dev, struct wacom_wac *wacom_wac)
{
input_dev->keybit[LONG(BTN_LEFT)] |= BIT(BTN_4) | BIT(BTN_5) | BIT(BTN_6) | BIT(BTN_7);
- input_set_abs_params(input_dev, ABS_RY, 0, 4097, 0, 0);
+ input_set_abs_params(input_dev, ABS_RY, 0, 4096, 0, 0);
}
void input_dev_i(struct input_dev *input_dev, struct wacom_wac *wacom_wac)
wacom_report_key(wcombo, BTN_STYLUS, data[1] & 0x02);
wacom_report_key(wcombo, BTN_STYLUS2, data[1] & 0x04);
}
- }
-
- if (data[1] & 0x10)
wacom_report_abs(wcombo, ABS_MISC, id); /* report tool id */
+ }
else
wacom_report_abs(wcombo, ABS_MISC, 0); /* reset tool id */
- wacom_report_key(wcombo, wacom->tool[0], data[1] & 0x10);
+
+ if (data[1] & 0x10) /* only report prox-in when in area */
+ wacom_report_key(wcombo, wacom->tool[0], 1);
+ if (!(data[1] & 0x90)) /* report prox-out when physically out */
+ wacom_report_key(wcombo, wacom->tool[0], 0);
wacom_input_sync(wcombo);
/* send pad data */
if ((wacom->features->type == CINTIQ) && !(data[1] & 0x40))
return 0;
- if (wacom->features->type >= INTUOS3) {
+ if (wacom->features->type >= INTUOS3S) {
wacom_report_abs(wcombo, ABS_X, (data[2] << 9) | (data[3] << 1) | ((data[9] >> 1) & 1));
wacom_report_abs(wcombo, ABS_Y, (data[4] << 9) | (data[5] << 1) | (data[9] & 1));
wacom_report_abs(wcombo, ABS_DISTANCE, ((data[9] >> 2) & 0x3f));
if (data[1] & 0x02) {
/* Rotation packet */
- if (wacom->features->type >= INTUOS3) {
+ if (wacom->features->type >= INTUOS3S) {
/* I3 marker pen rotation reported as wheel
* due to valuator limitation
*/
{ "Wacom Graphire3 6x8", 8, 16704, 12064, 511, 63, GRAPHIRE },
{ "Wacom Graphire4 4x5", 8, 10208, 7424, 511, 63, WACOM_G4 },
{ "Wacom Graphire4 6x8", 8, 16704, 12064, 511, 63, WACOM_G4 },
- { "Wacom Volito", 8, 5104, 3712, 511, 0, GRAPHIRE },
- { "Wacom PenStation2", 8, 3250, 2320, 255, 0, GRAPHIRE },
- { "Wacom Volito2 4x5", 8, 5104, 3712, 511, 0, GRAPHIRE },
- { "Wacom Volito2 2x3", 8, 3248, 2320, 511, 0, GRAPHIRE },
- { "Wacom PenPartner2", 8, 3250, 2320, 255, 0, GRAPHIRE },
+ { "Wacom Volito", 8, 5104, 3712, 511, 63, GRAPHIRE },
+ { "Wacom PenStation2", 8, 3250, 2320, 255, 63, GRAPHIRE },
+ { "Wacom Volito2 4x5", 8, 5104, 3712, 511, 63, GRAPHIRE },
+ { "Wacom Volito2 2x3", 8, 3248, 2320, 511, 63, GRAPHIRE },
+ { "Wacom PenPartner2", 8, 3250, 2320, 255, 63, GRAPHIRE },
{ "Wacom Intuos 4x5", 10, 12700, 10600, 1023, 63, INTUOS },
{ "Wacom Intuos 6x8", 10, 20320, 16240, 1023, 63, INTUOS },
{ "Wacom Intuos 9x12", 10, 30480, 24060, 1023, 63, INTUOS },
{ "Wacom Intuos3 12x12", 10, 60960, 60960, 1023, 63, INTUOS3L },
{ "Wacom Intuos3 12x19", 10, 97536, 60960, 1023, 63, INTUOS3L },
{ "Wacom Intuos3 6x11", 10, 54204, 31750, 1023, 63, INTUOS3 },
- { "Wacom Intuos3 4x6", 10, 31496, 19685, 1023, 15, INTUOS3S },
+ { "Wacom Intuos3 4x6", 10, 31496, 19685, 1023, 63, INTUOS3S },
{ "Wacom Cintiq 21UX", 10, 87200, 65600, 1023, 63, CINTIQ },
{ "Wacom Intuos2 6x8", 10, 20320, 16240, 1023, 63, INTUOS },
{ }
}
/* we have access to the device. Now lets allocate memory */
- ccp = (pauerchar_t) kmalloc(sizeof(auerchar_t), GFP_KERNEL);
+ ccp = kzalloc(sizeof(auerchar_t), GFP_KERNEL);
if (ccp == NULL) {
err ("out of memory");
ret = -ENOMEM;
}
/* Initialize device descriptor */
- memset( ccp, 0, sizeof(auerchar_t));
init_MUTEX( &ccp->mutex);
init_MUTEX( &ccp->readmutex);
auerbuf_init (&ccp->bufctl);
return -ENODEV;
/* allocate memory for our device and initialize it */
- cp = kmalloc (sizeof(auerswald_t), GFP_KERNEL);
+ cp = kzalloc (sizeof(auerswald_t), GFP_KERNEL);
if (cp == NULL) {
err ("out of memory");
goto pfail;
}
/* Initialize device descriptor */
- memset (cp, 0, sizeof(auerswald_t));
init_MUTEX (&cp->mutex);
cp->usbdev = usbdev;
auerchain_init (&cp->controlchain);
#include <linux/init.h>
#include <linux/list.h>
#include <linux/ioctl.h>
+#include <linux/pci_ids.h>
#include <linux/slab.h>
#include <linux/module.h>
#include <linux/kref.h>
MODULE_DESCRIPTION("FTDI ELAN driver");
MODULE_LICENSE("GPL");
#define INT_MODULE_PARM(n, v) static int n = v;module_param(n, int, 0444)
+static int distrust_firmware = 1;
+module_param(distrust_firmware, bool, 0);
+MODULE_PARM_DESC(distrust_firmware, "true to distrust firmware power/overcurren"
+ "t setup");
extern struct platform_driver u132_platform_driver;
static struct workqueue_struct *status_queue;
static struct workqueue_struct *command_queue;
* end of the global variables protected by ftdi_module_lock
*/
#include "usb_u132.h"
-#define TD_DEVNOTRESP 5
+#include <asm/io.h>
+#include "../core/hcd.h"
+#include "../host/ohci.h"
/* Define these values to match your devices*/
#define USB_FTDI_ELAN_VENDOR_ID 0x0403
#define USB_FTDI_ELAN_PRODUCT_ID 0xd6ea
} else {
dev_err(&ftdi->udev->dev, "initialized failed - trying "
"again in 10 seconds\n");
- work_delay_in_msec = 10 *1000;
+ work_delay_in_msec = 1 *1000;
}
} else if (ftdi->registered == 0) {
work_delay_in_msec = 10;
}
}
-static int ftdi_elan_enumeratePCI(struct usb_ftdi *ftdi)
+
+#define ftdi_read_pcimem(ftdi, member, data) ftdi_elan_read_pcimem(ftdi, \
+ offsetof(struct ohci_regs, member), 0, data);
+#define ftdi_write_pcimem(ftdi, member, data) ftdi_elan_write_pcimem(ftdi, \
+ offsetof(struct ohci_regs, member), 0, data);
+#define OHCI_QUIRK_AMD756 0x01
+#define OHCI_QUIRK_SUPERIO 0x02
+#define OHCI_QUIRK_INITRESET 0x04
+#define OHCI_BIG_ENDIAN 0x08
+#define OHCI_QUIRK_ZFMICRO 0x10
+#define OHCI_CONTROL_INIT OHCI_CTRL_CBSR
+#define OHCI_INTR_INIT (OHCI_INTR_MIE | OHCI_INTR_UE | OHCI_INTR_RD | \
+ OHCI_INTR_WDH)
+static int ftdi_elan_check_controller(struct usb_ftdi *ftdi, int quirk)
+{
+ int devices = 0;
+ int retval;
+ u32 hc_control;
+ int num_ports;
+ u32 control;
+ u32 rh_a = -1;
+ u32 status;
+ u32 fminterval;
+ u32 hc_fminterval;
+ u32 periodicstart;
+ u32 cmdstatus;
+ u32 roothub_a;
+ int mask = OHCI_INTR_INIT;
+ int sleep_time = 0;
+ int reset_timeout = 30; /* ... allow extra time */
+ int temp;
+ retval = ftdi_write_pcimem(ftdi, intrdisable, OHCI_INTR_MIE);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, control, &control);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, roothub.a, &rh_a);
+ if (retval)
+ return retval;
+ num_ports = rh_a & RH_A_NDP;
+ retval = ftdi_read_pcimem(ftdi, fminterval, &hc_fminterval);
+ if (retval)
+ return retval;
+ hc_fminterval &= 0x3fff;
+ if (hc_fminterval != FI) {
+ }
+ hc_fminterval |= FSMP(hc_fminterval) << 16;
+ retval = ftdi_read_pcimem(ftdi, control, &hc_control);
+ if (retval)
+ return retval;
+ switch (hc_control & OHCI_CTRL_HCFS) {
+ case OHCI_USB_OPER:
+ sleep_time = 0;
+ break;
+ case OHCI_USB_SUSPEND:
+ case OHCI_USB_RESUME:
+ hc_control &= OHCI_CTRL_RWC;
+ hc_control |= OHCI_USB_RESUME;
+ sleep_time = 10;
+ break;
+ default:
+ hc_control &= OHCI_CTRL_RWC;
+ hc_control |= OHCI_USB_RESET;
+ sleep_time = 50;
+ break;
+ }
+ retval = ftdi_write_pcimem(ftdi, control, hc_control);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, control, &control);
+ if (retval)
+ return retval;
+ msleep(sleep_time);
+ retval = ftdi_read_pcimem(ftdi, roothub.a, &roothub_a);
+ if (retval)
+ return retval;
+ if (!(roothub_a & RH_A_NPS)) { /* power down each port */
+ for (temp = 0; temp < num_ports; temp++) {
+ retval = ftdi_write_pcimem(ftdi,
+ roothub.portstatus[temp], RH_PS_LSDA);
+ if (retval)
+ return retval;
+ }
+ }
+ retval = ftdi_read_pcimem(ftdi, control, &control);
+ if (retval)
+ return retval;
+ retry:retval = ftdi_read_pcimem(ftdi, cmdstatus, &status);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, cmdstatus, OHCI_HCR);
+ if (retval)
+ return retval;
+ extra:{
+ retval = ftdi_read_pcimem(ftdi, cmdstatus, &status);
+ if (retval)
+ return retval;
+ if (0 != (status & OHCI_HCR)) {
+ if (--reset_timeout == 0) {
+ dev_err(&ftdi->udev->dev, "USB HC reset timed o"
+ "ut!\n");
+ return -ENODEV;
+ } else {
+ msleep(5);
+ goto extra;
+ }
+ }
+ }
+ if (quirk & OHCI_QUIRK_INITRESET) {
+ retval = ftdi_write_pcimem(ftdi, control, hc_control);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, control, &control);
+ if (retval)
+ return retval;
+ }
+ retval = ftdi_write_pcimem(ftdi, ed_controlhead, 0x00000000);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, ed_bulkhead, 0x11000000);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, hcca, 0x00000000);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, fminterval, &fminterval);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, fminterval,
+ ((fminterval & FIT) ^ FIT) | hc_fminterval);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, periodicstart,
+ ((9 *hc_fminterval) / 10) & 0x3fff);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, fminterval, &fminterval);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, periodicstart, &periodicstart);
+ if (retval)
+ return retval;
+ if (0 == (fminterval & 0x3fff0000) || 0 == periodicstart) {
+ if (!(quirk & OHCI_QUIRK_INITRESET)) {
+ quirk |= OHCI_QUIRK_INITRESET;
+ goto retry;
+ } else
+ dev_err(&ftdi->udev->dev, "init err(%08x %04x)\n",
+ fminterval, periodicstart);
+ } /* start controller operations */
+ hc_control &= OHCI_CTRL_RWC;
+ hc_control |= OHCI_CONTROL_INIT | OHCI_CTRL_BLE | OHCI_USB_OPER;
+ retval = ftdi_write_pcimem(ftdi, control, hc_control);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, cmdstatus, OHCI_BLF);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, cmdstatus, &cmdstatus);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, control, &control);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, roothub.status, RH_HS_DRWE);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, intrstatus, mask);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, intrdisable,
+ OHCI_INTR_MIE | OHCI_INTR_OC | OHCI_INTR_RHSC | OHCI_INTR_FNO |
+ OHCI_INTR_UE | OHCI_INTR_RD | OHCI_INTR_SF | OHCI_INTR_WDH |
+ OHCI_INTR_SO);
+ if (retval)
+ return retval; /* handle root hub init quirks ... */
+ retval = ftdi_read_pcimem(ftdi, roothub.a, &roothub_a);
+ if (retval)
+ return retval;
+ roothub_a &= ~(RH_A_PSM | RH_A_OCPM);
+ if (quirk & OHCI_QUIRK_SUPERIO) {
+ roothub_a |= RH_A_NOCP;
+ roothub_a &= ~(RH_A_POTPGT | RH_A_NPS);
+ retval = ftdi_write_pcimem(ftdi, roothub.a, roothub_a);
+ if (retval)
+ return retval;
+ } else if ((quirk & OHCI_QUIRK_AMD756) || distrust_firmware) {
+ roothub_a |= RH_A_NPS;
+ retval = ftdi_write_pcimem(ftdi, roothub.a, roothub_a);
+ if (retval)
+ return retval;
+ }
+ retval = ftdi_write_pcimem(ftdi, roothub.status, RH_HS_LPSC);
+ if (retval)
+ return retval;
+ retval = ftdi_write_pcimem(ftdi, roothub.b,
+ (roothub_a & RH_A_NPS) ? 0 : RH_B_PPCM);
+ if (retval)
+ return retval;
+ retval = ftdi_read_pcimem(ftdi, control, &control);
+ if (retval)
+ return retval;
+ mdelay((roothub_a >> 23) & 0x1fe);
+ for (temp = 0; temp < num_ports; temp++) {
+ u32 portstatus;
+ retval = ftdi_read_pcimem(ftdi, roothub.portstatus[temp],
+ &portstatus);
+ if (retval)
+ return retval;
+ if (1 & portstatus)
+ devices += 1;
+ }
+ return devices;
+}
+
+static int ftdi_elan_setup_controller(struct usb_ftdi *ftdi, int fn)
{
u32 latence_timer;
- u32 controlreg;
int UxxxStatus;
u32 pcidata;
int reg = 0;
- int foundOHCI = 0;
- u8 fn;
- int activePCIfn = 0;
- u32 pciVID = 0;
- u32 pciPID = 0;
- UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
- if (UxxxStatus)
- return UxxxStatus;
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x00000000L);
- if (UxxxStatus)
- return UxxxStatus;
- msleep(750);
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x00000200L | 0x100);
+ int activePCIfn = fn << 8;
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000025FL | 0x2800);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x00000200L | 0x500);
+ reg = 16;
+ UxxxStatus = ftdi_elan_write_config(ftdi, activePCIfn | reg, 0,
+ 0xFFFFFFFF);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
+ &pcidata);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000020CL | 0x000);
+ UxxxStatus = ftdi_elan_write_config(ftdi, activePCIfn | reg, 0,
+ 0xF0000000);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000020DL | 0x000);
+ UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
+ &pcidata);
if (UxxxStatus)
return UxxxStatus;
- msleep(250);
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000020FL | 0x000);
+ reg = 12;
+ UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
+ &latence_timer);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ latence_timer &= 0xFFFF00FF;
+ latence_timer |= 0x00001600;
+ UxxxStatus = ftdi_elan_write_config(ftdi, activePCIfn | reg, 0x00,
+ latence_timer);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000025FL | 0x800);
+ UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
+ &pcidata);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ reg = 4;
+ UxxxStatus = ftdi_elan_write_config(ftdi, activePCIfn | reg, 0x00,
+ 0x06);
if (UxxxStatus)
return UxxxStatus;
- UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
+ &pcidata);
if (UxxxStatus)
return UxxxStatus;
- msleep(1000);
- for (fn = 0; (fn < 4) && (!foundOHCI); fn++) {
- activePCIfn = fn << 8;
- ftdi->function = fn + 1;
- UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
- &pcidata);
+ for (reg = 0; reg <= 0x54; reg += 4) {
+ UxxxStatus = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
if (UxxxStatus)
return UxxxStatus;
- pciVID = pcidata & 0xFFFF;
- pciPID = (pcidata >> 16) & 0xFFFF;
- if ((pciVID == 0x1045) && (pciPID == 0xc861)) {
- foundOHCI = 1;
- } else if ((pciVID == 0x1033) && (pciPID == 0x0035)) {
- foundOHCI = 1;
- } else if ((pciVID == 0x10b9) && (pciPID == 0x5237)) {
- foundOHCI = 1;
- } else if ((pciVID == 0x11c1) && (pciPID == 0x5802)) {
- foundOHCI = 1;
- } else if ((pciVID == 0x11AB) && (pciPID == 0x1FA6)) {
- }
- }
- if (foundOHCI == 0) {
- return -ENXIO;
}
- ftdi->platform_data.vendor = pciVID;
- ftdi->platform_data.device = pciPID;
+ return 0;
+}
+
+static int ftdi_elan_close_controller(struct usb_ftdi *ftdi, int fn)
+{
+ u32 latence_timer;
+ int UxxxStatus;
+ u32 pcidata;
+ int reg = 0;
+ int activePCIfn = fn << 8;
UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000025FL | 0x2800);
if (UxxxStatus)
return UxxxStatus;
if (UxxxStatus)
return UxxxStatus;
UxxxStatus = ftdi_elan_write_config(ftdi, activePCIfn | reg, 0,
- 0xF0000000);
+ 0x00000000);
if (UxxxStatus)
return UxxxStatus;
UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
return UxxxStatus;
reg = 4;
UxxxStatus = ftdi_elan_write_config(ftdi, activePCIfn | reg, 0x00,
- 0x06);
+ 0x00);
if (UxxxStatus)
return UxxxStatus;
UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
return 0;
}
+static int ftdi_elan_found_controller(struct usb_ftdi *ftdi, int fn, int quirk)
+{
+ int result;
+ int UxxxStatus;
+ UxxxStatus = ftdi_elan_setup_controller(ftdi, fn);
+ if (UxxxStatus)
+ return UxxxStatus;
+ result = ftdi_elan_check_controller(ftdi, quirk);
+ UxxxStatus = ftdi_elan_close_controller(ftdi, fn);
+ if (UxxxStatus)
+ return UxxxStatus;
+ return result;
+}
+
+static int ftdi_elan_enumeratePCI(struct usb_ftdi *ftdi)
+{
+ u32 controlreg;
+ u8 sensebits;
+ int UxxxStatus;
+ UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x00000000L);
+ if (UxxxStatus)
+ return UxxxStatus;
+ msleep(750);
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x00000200L | 0x100);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x00000200L | 0x500);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000020CL | 0x000);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000020DL | 0x000);
+ if (UxxxStatus)
+ return UxxxStatus;
+ msleep(250);
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000020FL | 0x000);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_write_reg(ftdi, 0x0000025FL | 0x800);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ if (UxxxStatus)
+ return UxxxStatus;
+ UxxxStatus = ftdi_elan_read_reg(ftdi, &controlreg);
+ if (UxxxStatus)
+ return UxxxStatus;
+ msleep(1000);
+ sensebits = (controlreg >> 16) & 0x000F;
+ if (0x0D == sensebits)
+ return 0;
+ else
+ return - ENXIO;
+}
+
static int ftdi_elan_setupOHCI(struct usb_ftdi *ftdi)
{
+ int UxxxStatus;
u32 pcidata;
- int U132Status;
- int reg;
- int reset_repeat = 0;
- do_reset:reg = 8;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x0e, 0x01);
- if (U132Status)
- return U132Status;
- reset_check:{
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- if (pcidata & 1) {
- msleep(500);
- if (reset_repeat++ > 100) {
- reset_repeat = 0;
- goto do_reset;
- } else
- goto reset_check;
+ int reg = 0;
+ u8 fn;
+ int activePCIfn = 0;
+ int max_devices = 0;
+ int controllers = 0;
+ int unrecognized = 0;
+ ftdi->function = 0;
+ for (fn = 0; (fn < 4); fn++) {
+ u32 pciVID = 0;
+ u32 pciPID = 0;
+ int devices = 0;
+ activePCIfn = fn << 8;
+ UxxxStatus = ftdi_elan_read_config(ftdi, activePCIfn | reg, 0,
+ &pcidata);
+ if (UxxxStatus)
+ return UxxxStatus;
+ pciVID = pcidata & 0xFFFF;
+ pciPID = (pcidata >> 16) & 0xFFFF;
+ if ((pciVID == PCI_VENDOR_ID_OPTI) && (pciPID == 0xc861)) {
+ devices = ftdi_elan_found_controller(ftdi, fn, 0);
+ controllers += 1;
+ } else if ((pciVID == PCI_VENDOR_ID_NEC) && (pciPID == 0x0035))
+ {
+ devices = ftdi_elan_found_controller(ftdi, fn, 0);
+ controllers += 1;
+ } else if ((pciVID == PCI_VENDOR_ID_AL) && (pciPID == 0x5237)) {
+ devices = ftdi_elan_found_controller(ftdi, fn, 0);
+ controllers += 1;
+ } else if ((pciVID == PCI_VENDOR_ID_ATT) && (pciPID == 0x5802))
+ {
+ devices = ftdi_elan_found_controller(ftdi, fn, 0);
+ controllers += 1;
+ } else if (pciVID == PCI_VENDOR_ID_AMD && pciPID == 0x740c) {
+ devices = ftdi_elan_found_controller(ftdi, fn,
+ OHCI_QUIRK_AMD756);
+ controllers += 1;
+ } else if (pciVID == PCI_VENDOR_ID_COMPAQ && pciPID == 0xa0f8) {
+ devices = ftdi_elan_found_controller(ftdi, fn,
+ OHCI_QUIRK_ZFMICRO);
+ controllers += 1;
+ } else if (0 == pcidata) {
+ } else
+ unrecognized += 1;
+ if (devices > max_devices) {
+ max_devices = devices;
+ ftdi->function = fn + 1;
+ ftdi->platform_data.vendor = pciVID;
+ ftdi->platform_data.device = pciPID;
}
}
- goto dump_regs;
- msleep(500);
- reg = 0x28;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x11000000);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x40;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x2edf);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x34;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x2edf2edf);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 4;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0xA0);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- msleep(250);
- reg = 8;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x0e, 0x04);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x28;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 8;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x48;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x00001200);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x54;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x58;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x34;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x28002edf);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- msleep(100);
- reg = 0x50;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x10000);
- if (U132Status)
- return U132Status;
- reg = 0x54;
- power_check:U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- if (!(pcidata & 1)) {
- msleep(500);
- goto power_check;
- }
- msleep(3000);
- reg = 0x54;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x58;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x54;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x02);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x54;
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x10);
- if (U132Status)
- return U132Status;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- msleep(750);
- reg = 0x54;
- if (0) {
- U132Status = ftdi_elan_write_pcimem(ftdi, reg, 0x00, 0x02);
- if (U132Status)
- return U132Status;
- }
- if (0) {
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- }
- reg = 0x54;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- reg = 0x58;
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
- dump_regs:for (reg = 0; reg <= 0x54; reg += 4) {
- U132Status = ftdi_elan_read_pcimem(ftdi, reg, 0, &pcidata);
- if (U132Status)
- return U132Status;
+ if (ftdi->function > 0) {
+ UxxxStatus = ftdi_elan_setup_controller(ftdi,
+ ftdi->function - 1);
+ if (UxxxStatus)
+ return UxxxStatus;
+ return 0;
+ } else if (controllers > 0) {
+ return -ENXIO;
+ } else if (unrecognized > 0) {
+ return -ENXIO;
+ } else {
+ ftdi->enumerated = 0;
+ return -ENXIO;
}
- return 0;
}
platform_device_unregister(&ftdi->platform_dev);
ftdi->synchronized = 0;
ftdi->enumerated = 0;
+ ftdi->initialized = 0;
ftdi->registered = 0;
}
flush_workqueue(status_queue);
dev->dev = NULL;
goto out;
}
+ dev_set_drvdata(dev->dev, dev);
servo_count = dev->type & SERVO_COUNT_QUAD ? 4 : 1;
struct trancevibrator *dev;
dev = usb_get_intfdata (interface);
- usb_set_intfdata(interface, NULL);
device_remove_file(&interface->dev, &dev_attr_speed);
+ usb_set_intfdata(interface, NULL);
usb_put_dev(dev->udev);
kfree(dev);
}
struct gl_packet packets;
};
-#ifdef GENELINK_ACK
-
-// FIXME: this code is incomplete, not debugged; it doesn't
-// handle interrupts correctly; it should use the generic
-// status IRQ code (which didn't exist back in 2001).
-
-struct gl_priv {
- struct urb *irq_urb;
- char irq_buf [INTERRUPT_BUFSIZE];
-};
-
-static inline int gl_control_write(struct usbnet *dev, u8 request, u16 value)
-{
- int retval;
-
- retval = usb_control_msg(dev->udev,
- usb_sndctrlpipe(dev->udev, 0),
- request,
- USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE,
- value,
- 0, // index
- 0, // data buffer
- 0, // size
- USB_CTRL_SET_TIMEOUT);
- return retval;
-}
-
-static void gl_interrupt_complete(struct urb *urb)
-{
- int status = urb->status;
-
- switch (status) {
- case 0:
- /* success */
- break;
- case -ECONNRESET:
- case -ENOENT:
- case -ESHUTDOWN:
- /* this urb is terminated, clean up */
- dbg("%s - urb shutting down with status: %d",
- __FUNCTION__, status);
- return;
- default:
- dbg("%s - nonzero urb status received: %d",
- __FUNCTION__, urb->status);
- }
-
- status = usb_submit_urb(urb, GFP_ATOMIC);
- if (status)
- err("%s - usb_submit_urb failed with result %d",
- __FUNCTION__, status);
-}
-
-static int gl_interrupt_read(struct usbnet *dev)
-{
- struct gl_priv *priv = dev->priv_data;
- int retval;
-
- // issue usb interrupt read
- if (priv && priv->irq_urb) {
- // submit urb
- if ((retval = usb_submit_urb(priv->irq_urb, GFP_KERNEL)) != 0)
- dbg("gl_interrupt_read: submit fail - %X...", retval);
- else
- dbg("gl_interrupt_read: submit success...");
- }
-
- return 0;
-}
-
-// check whether another side is connected
-static int genelink_check_connect(struct usbnet *dev)
-{
- int retval;
-
- dbg("genelink_check_connect...");
-
- // detect whether another side is connected
- if ((retval = gl_control_write(dev, GENELINK_CONNECT_WRITE, 0)) != 0) {
- dbg("%s: genelink_check_connect write fail - %X",
- dev->net->name, retval);
- return retval;
- }
-
- // usb interrupt read to ack another side
- if ((retval = gl_interrupt_read(dev)) != 0) {
- dbg("%s: genelink_check_connect read fail - %X",
- dev->net->name, retval);
- return retval;
- }
-
- dbg("%s: genelink_check_connect read success", dev->net->name);
- return 0;
-}
-
-// allocate and initialize the private data for genelink
-static int genelink_init(struct usbnet *dev)
-{
- struct gl_priv *priv;
-
- // allocate the private data structure
- if ((priv = kmalloc(sizeof *priv, GFP_KERNEL)) == 0) {
- dbg("%s: cannot allocate private data per device",
- dev->net->name);
- return -ENOMEM;
- }
-
- // allocate irq urb
- if ((priv->irq_urb = usb_alloc_urb(0, GFP_KERNEL)) == 0) {
- dbg("%s: cannot allocate private irq urb per device",
- dev->net->name);
- kfree(priv);
- return -ENOMEM;
- }
-
- // fill irq urb
- usb_fill_int_urb(priv->irq_urb, dev->udev,
- usb_rcvintpipe(dev->udev, GENELINK_INTERRUPT_PIPE),
- priv->irq_buf, INTERRUPT_BUFSIZE,
- gl_interrupt_complete, 0,
- GENELINK_INTERRUPT_INTERVAL);
-
- // set private data pointer
- dev->priv_data = priv;
-
- return 0;
-}
-
-// release the private data
-static int genelink_free(struct usbnet *dev)
-{
- struct gl_priv *priv = dev->priv_data;
-
- if (!priv)
- return 0;
-
-// FIXME: can't cancel here; it's synchronous, and
-// should have happened earlier in any case (interrupt
-// handling needs to be generic)
-
- // cancel irq urb first
- usb_kill_urb(priv->irq_urb);
-
- // free irq urb
- usb_free_urb(priv->irq_urb);
-
- // free the private data structure
- kfree(priv);
-
- return 0;
-}
-
-#endif
-
static int genelink_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
{
struct gl_header *header;
#define RX_URB_FAIL 3
/* Define these values to match your device */
-#define VENDOR_ID_REALTEK 0x0bda
+#define VENDOR_ID_REALTEK 0x0bda
#define VENDOR_ID_MELCO 0x0411
-#define VENDOR_ID_MICRONET 0x3980
+#define VENDOR_ID_MICRONET 0x3980
#define VENDOR_ID_LONGSHINE 0x07b8
+#define VENDOR_ID_OQO 0x1557
#define VENDOR_ID_ZYXEL 0x0586
#define PRODUCT_ID_RTL8150 0x8150
{USB_DEVICE(VENDOR_ID_MELCO, PRODUCT_ID_LUAKTX)},
{USB_DEVICE(VENDOR_ID_MICRONET, PRODUCT_ID_SP128AR)},
{USB_DEVICE(VENDOR_ID_LONGSHINE, PRODUCT_ID_LCS8138TX)},
+ {USB_DEVICE(VENDOR_ID_OQO, PRODUCT_ID_RTL8150)},
{USB_DEVICE(VENDOR_ID_ZYXEL, PRODUCT_ID_PRESTIGE)},
{}
};
static struct usb_device_id id_table [] = {
{ USB_DEVICE(0x0c88, 0x17da) }, /* Kyocera Wireless KPC650/Passport */
{ USB_DEVICE(0x1410, 0x1110) }, /* Novatel Wireless Merlin CDMA */
+ { USB_DEVICE(0x1410, 0x1130) }, /* Novatel Wireless S720 CDMA/EV-DO */
+ { USB_DEVICE(0x1410, 0x2110) }, /* Novatel Wireless U720 CDMA/EV-DO */
{ USB_DEVICE(0x1410, 0x1430) }, /* Novatel Merlin XU870 HSDPA/3G */
{ USB_DEVICE(0x1410, 0x1100) }, /* ExpressCard34 Qualcomm 3G CDMA */
+ { USB_DEVICE(0x413c, 0x8115) }, /* Dell Wireless HSDPA 5500 */
{ },
};
MODULE_DEVICE_TABLE(usb, id_table);
{ USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
+ { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
{ USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
{ } /* Terminating Entry */
};
cypress_set_termios(port, &priv->tmp_termios);
return (0);
break;
- /* these are called when setting baud rate from gpsd */
- case TCGETS:
- if (copy_to_user((void __user *)arg, port->tty->termios, sizeof(struct termios))) {
- return -EFAULT;
- }
- return (0);
- break;
- case TCSETS:
- if (copy_from_user(port->tty->termios, (void __user *)arg, sizeof(struct termios))) {
- return -EFAULT;
- }
- /* here we need to call cypress_set_termios to invoke the new settings */
- cypress_set_termios(port, &priv->tmp_termios);
- return (0);
- break;
/* This code comes from drivers/char/serial.c and ftdi_sio.c */
case TIOCMIWAIT:
while (priv != NULL) {
{ USB_DEVICE(FTDI_VID, LINX_FUTURE_2_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSICDU20_0_PID) },
{ USB_DEVICE(FTDI_VID, FTDI_CCSICDU40_1_PID) },
+ { USB_DEVICE(FTDI_VID, FTDI_CCSMACHX_2_PID) },
{ USB_DEVICE(FTDI_VID, INSIDE_ACCESSO) },
{ USB_DEVICE(INTREPID_VID, INTREPID_VALUECAN_PID) },
{ USB_DEVICE(INTREPID_VID, INTREPID_NEOVI_PID) },
/* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
/* unit for PIC16's/PIC18's */
-#define FTDI_CCSICDU20_0_PID 0xF9D0
-#define FTDI_CCSICDU40_1_PID 0xF9D1
+#define FTDI_CCSICDU20_0_PID 0xF9D0
+#define FTDI_CCSICDU40_1_PID 0xF9D1
+#define FTDI_CCSMACHX_2_PID 0xF9D2
/* Inside Accesso contactless reader (http://www.insidefr.com) */
#define INSIDE_ACCESSO 0xFAD0
#include <linux/module.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
+#include <asm/uaccess.h>
+
+static int debug;
static struct usb_device_id id_table [] = {
{ USB_DEVICE(0x1404, 0xcddc) },
};
MODULE_DEVICE_TABLE(usb, id_table);
+static int funsoft_ioctl(struct usb_serial_port *port, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ struct termios t;
+
+ dbg("%s - port %d, cmd 0x%04x", __FUNCTION__, port->number, cmd);
+
+ if (cmd == TCSETSF) {
+ if (user_termios_to_kernel_termios(&t, (void __user *)arg))
+ return -EFAULT;
+
+ dbg("%s - iflag:%x oflag:%x cflag:%x lflag:%x", __FUNCTION__,
+ t.c_iflag, t.c_oflag, t.c_cflag, t.c_lflag);
+
+ if (!(t.c_lflag & ICANON))
+ return -EINVAL;
+ }
+ return -ENOIOCTLCMD;
+}
+
static struct usb_driver funsoft_driver = {
.name = "funsoft",
.probe = usb_serial_probe,
.num_bulk_in = NUM_DONT_CARE,
.num_bulk_out = NUM_DONT_CARE,
.num_ports = 1,
+ .ioctl = funsoft_ioctl,
};
static int __init funsoft_init(void)
module_init(funsoft_init);
module_exit(funsoft_exit);
MODULE_LICENSE("GPL");
+
+module_param(debug, bool, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(debug, "Debug enabled or not");
static void klsi_105_read_bulk_callback (struct urb *urb);
static void klsi_105_set_termios (struct usb_serial_port *port,
struct ktermios *old);
-static int klsi_105_ioctl (struct usb_serial_port *port,
- struct file * file,
- unsigned int cmd,
- unsigned long arg);
static void klsi_105_throttle (struct usb_serial_port *port);
static void klsi_105_unthrottle (struct usb_serial_port *port);
/*
.chars_in_buffer = klsi_105_chars_in_buffer,
.write_room = klsi_105_write_room,
.read_bulk_callback =klsi_105_read_bulk_callback,
- .ioctl = klsi_105_ioctl,
.set_termios = klsi_105_set_termios,
/*.break_ctl = klsi_105_break_ctl,*/
.tiocmget = klsi_105_tiocmget,
*/
return retval;
}
-
-static int klsi_105_ioctl (struct usb_serial_port *port, struct file * file,
- unsigned int cmd, unsigned long arg)
-{
- struct klsi_105_private *priv = usb_get_serial_port_data(port);
- void __user *user_arg = (void __user *)arg;
-
- dbg("%scmd=0x%x", __FUNCTION__, cmd);
-
- /* Based on code from acm.c and others */
- switch (cmd) {
- case TIOCMIWAIT:
- /* wait for any of the 4 modem inputs (DCD,RI,DSR,CTS)*/
- /* TODO */
- dbg("%s - TIOCMIWAIT not handled", __FUNCTION__);
- return -ENOIOCTLCMD;
- case TIOCGICOUNT:
- /* return count of modemline transitions */
- /* TODO */
- dbg("%s - TIOCGICOUNT not handled", __FUNCTION__);
- return -ENOIOCTLCMD;
- case TCGETS:
- /* return current info to caller */
- dbg("%s - TCGETS data faked/incomplete", __FUNCTION__);
-
- if (!access_ok(VERIFY_WRITE, user_arg, sizeof(struct termios)))
- return -EFAULT;
-
- if (kernel_termios_to_user_termios((struct termios __user *)arg,
- &priv->termios))
- return -EFAULT;
- return 0;
- case TCSETS:
- /* set port termios to the one given by the user */
- dbg("%s - TCSETS not handled", __FUNCTION__);
-
- if (!access_ok(VERIFY_READ, user_arg, sizeof(struct termios)))
- return -EFAULT;
-
- if (user_termios_to_kernel_termios(&priv->termios,
- (struct termios __user *)arg))
- return -EFAULT;
- klsi_105_set_termios(port, &priv->termios);
- return 0;
- case TCSETSW: {
- /* set port termios and try to wait for completion of last
- * write operation */
- /* We guess here. If there are not too many write urbs
- * outstanding, we lie. */
- /* what is the right way to wait here? schedule() ? */
- /*
- while (klsi_105_chars_in_buffer(port) > (NUM_URBS / 4 ) * URB_TRANSFER_BUFFER_SIZE)
- schedule();
- */
- return -ENOIOCTLCMD;
- }
- default:
- dbg("%s: arg not supported - 0x%04x", __FUNCTION__,cmd);
- return(-ENOIOCTLCMD);
- break;
- }
- return 0;
-} /* klsi_105_ioctl */
static void klsi_105_throttle (struct usb_serial_port *port)
{
tty_ldisc_deref(ld);
return 0;
- case TCGETS:
- if (kernel_termios_to_user_termios
- ((struct termios __user *)argp, tty->termios))
- return -EFAULT;
- return 0;
-
case TIOCSERGETLSR:
dbg("%s (%d) TIOCSERGETLSR", __FUNCTION__, port->number);
return mos7840_get_lsr_info(mos7840_port, argp);
#define OPTION_PRODUCT_COBRA 0x6500
#define OPTION_PRODUCT_COBRA2 0x6600
#define HUAWEI_PRODUCT_E600 0x1001
+#define HUAWEI_PRODUCT_E220 0x1003
#define AUDIOVOX_PRODUCT_AIRCARD 0x0112
#define NOVATELWIRELESS_PRODUCT_U740 0x1400
#define ANYDATA_PRODUCT_ID 0x6501
{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COBRA) },
{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COBRA2) },
{ USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E600) },
+ { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E220) },
{ USB_DEVICE(AUDIOVOX_VENDOR_ID, AUDIOVOX_PRODUCT_AIRCARD) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID,NOVATELWIRELESS_PRODUCT_U740) },
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ID) },
{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COBRA) },
{ USB_DEVICE(OPTION_VENDOR_ID, OPTION_PRODUCT_COBRA2) },
{ USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E600) },
+ { USB_DEVICE(HUAWEI_VENDOR_ID, HUAWEI_PRODUCT_E220) },
{ USB_DEVICE(AUDIOVOX_VENDOR_ID, AUDIOVOX_PRODUCT_AIRCARD) },
{ USB_DEVICE(NOVATELWIRELESS_VENDOR_ID,NOVATELWIRELESS_PRODUCT_U740) },
{ USB_DEVICE(ANYDATA_VENDOR_ID, ANYDATA_PRODUCT_ID) },
US_SC_DEVICE, US_PR_DEVICE, NULL,
US_FL_IGNORE_RESIDUE | US_FL_FIX_CAPACITY ),
+/* Reported by <honkkis@gmail.com> */
+UNUSUAL_DEV( 0x0421, 0x0433, 0x0100, 0x0100,
+ "Nokia",
+ "E70",
+ US_SC_DEVICE, US_PR_DEVICE, NULL,
+ US_FL_IGNORE_RESIDUE | US_FL_FIX_CAPACITY ),
+
/* Reported by Jon Hart <Jon.Hart@web.de> */
UNUSUAL_DEV( 0x0421, 0x0434, 0x0100, 0x0100,
"Nokia",
US_SC_DEVICE, US_PR_DEVICE, NULL,
US_FL_IGNORE_RESIDUE ),
+/* This prevents the kernel from detecting the virtual cd-drive with the
+ * Windows drivers. <johann.wilhelm@student.tugraz.at>
+*/
+UNUSUAL_DEV( 0x12d1, 0x1003, 0x0000, 0xffff,
+ "HUAWEI",
+ "E220 USB-UMTS Install",
+ US_SC_DEVICE, US_PR_DEVICE, NULL,
+ US_FL_IGNORE_DEVICE),
+
/* Reported by Vilius Bilinkevicius <vilisas AT xxx DOT lt) */
UNUSUAL_DEV( 0x132b, 0x000b, 0x0001, 0x0001,
"Minolta",
done:
if (res_specified) {
dev_info(dev, "overriding resolution: %dx%d\n", xres, yres);
- inf->xres = xres; inf->yres = yres;
+ inf->modes[0].xres = xres; inf->modes[0].yres = yres;
}
if (bpp_specified)
switch (bpp) {
case 4:
case 8:
case 16:
- inf->bpp = bpp;
+ inf->modes[0].bpp = bpp;
dev_info(dev, "overriding bit depth: %d\n", bpp);
break;
default:
dev_err(dev, "Depth %d is not valid\n", bpp);
}
} else if (!strncmp(this_opt, "pixclock:", 9)) {
- inf->pixclock = simple_strtoul(this_opt+9, NULL, 0);
- dev_info(dev, "override pixclock: %ld\n", inf->pixclock);
+ inf->modes[0].pixclock = simple_strtoul(this_opt+9, NULL, 0);
+ dev_info(dev, "override pixclock: %ld\n", inf->modes[0].pixclock);
} else if (!strncmp(this_opt, "left:", 5)) {
- inf->left_margin = simple_strtoul(this_opt+5, NULL, 0);
- dev_info(dev, "override left: %u\n", inf->left_margin);
+ inf->modes[0].left_margin = simple_strtoul(this_opt+5, NULL, 0);
+ dev_info(dev, "override left: %u\n", inf->modes[0].left_margin);
} else if (!strncmp(this_opt, "right:", 6)) {
- inf->right_margin = simple_strtoul(this_opt+6, NULL, 0);
- dev_info(dev, "override right: %u\n", inf->right_margin);
+ inf->modes[0].right_margin = simple_strtoul(this_opt+6, NULL, 0);
+ dev_info(dev, "override right: %u\n", inf->modes[0].right_margin);
} else if (!strncmp(this_opt, "upper:", 6)) {
- inf->upper_margin = simple_strtoul(this_opt+6, NULL, 0);
- dev_info(dev, "override upper: %u\n", inf->upper_margin);
+ inf->modes[0].upper_margin = simple_strtoul(this_opt+6, NULL, 0);
+ dev_info(dev, "override upper: %u\n", inf->modes[0].upper_margin);
} else if (!strncmp(this_opt, "lower:", 6)) {
- inf->lower_margin = simple_strtoul(this_opt+6, NULL, 0);
- dev_info(dev, "override lower: %u\n", inf->lower_margin);
+ inf->modes[0].lower_margin = simple_strtoul(this_opt+6, NULL, 0);
+ dev_info(dev, "override lower: %u\n", inf->modes[0].lower_margin);
} else if (!strncmp(this_opt, "hsynclen:", 9)) {
- inf->hsync_len = simple_strtoul(this_opt+9, NULL, 0);
- dev_info(dev, "override hsynclen: %u\n", inf->hsync_len);
+ inf->modes[0].hsync_len = simple_strtoul(this_opt+9, NULL, 0);
+ dev_info(dev, "override hsynclen: %u\n", inf->modes[0].hsync_len);
} else if (!strncmp(this_opt, "vsynclen:", 9)) {
- inf->vsync_len = simple_strtoul(this_opt+9, NULL, 0);
- dev_info(dev, "override vsynclen: %u\n", inf->vsync_len);
+ inf->modes[0].vsync_len = simple_strtoul(this_opt+9, NULL, 0);
+ dev_info(dev, "override vsynclen: %u\n", inf->modes[0].vsync_len);
} else if (!strncmp(this_opt, "hsync:", 6)) {
if (simple_strtoul(this_opt+6, NULL, 0) == 0) {
dev_info(dev, "override hsync: Active Low\n");
- inf->sync &= ~FB_SYNC_HOR_HIGH_ACT;
+ inf->modes[0].sync &= ~FB_SYNC_HOR_HIGH_ACT;
} else {
dev_info(dev, "override hsync: Active High\n");
- inf->sync |= FB_SYNC_HOR_HIGH_ACT;
+ inf->modes[0].sync |= FB_SYNC_HOR_HIGH_ACT;
}
} else if (!strncmp(this_opt, "vsync:", 6)) {
if (simple_strtoul(this_opt+6, NULL, 0) == 0) {
dev_info(dev, "override vsync: Active Low\n");
- inf->sync &= ~FB_SYNC_VERT_HIGH_ACT;
+ inf->modes[0].sync &= ~FB_SYNC_VERT_HIGH_ACT;
} else {
dev_info(dev, "override vsync: Active High\n");
- inf->sync |= FB_SYNC_VERT_HIGH_ACT;
+ inf->modes[0].sync |= FB_SYNC_VERT_HIGH_ACT;
}
} else if (!strncmp(this_opt, "dpc:", 4)) {
if (simple_strtoul(this_opt+4, NULL, 0) == 0) {
* Our LCD controller task (which is called when we blank or unblank)
* via keventd.
*/
-static void sa1100fb_task(void *dummy)
+static void sa1100fb_task(struct work_struct *w)
{
- struct sa1100fb_info *fbi = dummy;
+ struct sa1100fb_info *fbi = container_of(w, struct sa1100fb_info, task);
u_int state = xchg(&fbi->task_state, -1);
set_ctrlr_state(fbi, state);
fbi->max_bpp / 8;
init_waitqueue_head(&fbi->ctrlr_wait);
- INIT_WORK(&fbi->task, sa1100fb_task, fbi);
+ INIT_WORK(&fbi->task, sa1100fb_task);
init_MUTEX(&fbi->ctrlr_sem);
return fbi;
#define PBI_CF_IDE_BASE (IQ81340_CMP_FLSH)
#define PBI_CF_BAR_ADDR (IOP13XX_PBI_BAR1)
-/* These are the values used in the Machine description */
-#define PHYS_IO 0xfeffff00
-#define IO_PG_OFFSET 0xffffff00
-#define BOOT_PARAM_OFFSET 0x00000100
+
#endif /* _IQ81340_H_ */
data = *((volatile int *)IXP23XX_PCI_SDRAM_BAR); \
__phys_to_virt((((b - (data & 0xfffffff0)) + 0x00000000))); })
-/*
- * Coherency support. Only supported on A2 CPUs or on A1
- * systems that have the cache coherency workaround.
- */
-static inline int __ixp23xx_arch_is_coherent(void)
-{
- extern unsigned int processor_id;
-
- if (((processor_id & 15) >= 4) || machine_is_roadrunner())
- return 1;
-
- return 0;
-}
-
-#define arch_is_coherent() __ixp23xx_arch_is_coherent()
+#define arch_is_coherent() 1
#endif
/* linux/include/asm-arm/arch-s3c2410/anubis-cpld.h
*
- * (c) 2005 Simtec Electronics
+ * Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
/* linux/include/asm-arm/arch-s3c2410/anubis-irq.h
*
- * (c) 2005 Simtec Electronics
+ * Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
/* linux/include/asm-arm/arch-s3c2410/anubis-map.h
*
- * (c) 2005 Simtec Electronics
+ * Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
/* linux/include/asm-arm/arch-s3c2410/audio.h
*
- * (c) 2004-2005 Simtec Electronics
+ * Copyright (c) 2004-2005 Simtec Electronics
* http://www.simtec.co.uk/products/SWLINUX/
* Ben Dooks <ben@simtec.co.uk>
*
/* linux/include/asm-arm/arch-s3c2410/bast-cpld.h
*
- * (c) 2003,2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003,2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* BAST - CPLD control constants
*
/* linux/include/asm-arm/arch-s3c2410/bast-irq.h
*
- * (c) 2003,2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003,2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* Machine BAST - IRQ Number definitions
*
/* linux/include/asm-arm/arch-s3c2410/bast-map.h
*
- * (c) 2003,2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003,2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* Machine BAST - Memory map definitions
*
/* linux/include/asm-arm/arch-s3c2410/bast-pmu.h
*
- * (c) 2003,2004 Simtec Electronics
+ * Copyright (c) 2003,2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
* Vincent Sanders <vince@simtec.co.uk>
*
/* linux/include/asm-arm/arch-s3c2410/h1940-latch.h
*
- * (c) 2005 Simtec Electronics
+ * Copyright (c) 2005 Simtec Electronics
* http://armlinux.simtec.co.uk/
* Ben Dooks <ben@simtec.co.uk>
*
#ifndef __ASSEMBLY__
-#define H1940_LATCH ((void __iomem *)0xF8000000)
+#define H1940_LATCH ((void __force __iomem *)0xF8000000)
#else
#define H1940_LATCH 0xF8000000
#endif
/* linux/include/asm-arm/arch-s3c2410/hardware.h
*
- * (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - hardware
*
/* linux/include/asm-arm/arch-s3c2410/iic.h
*
- * (c) 2004 Simtec Electronics
+ * Copyright (c) 2004 Simtec Electronics
* Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - I2C Controller platfrom_device info
/* linux/include/asm-arm/arch-s3c2410/leds-gpio.h
*
- * (c) 2006 Simtec Electronics
+ * Copyright (c) 2006 Simtec Electronics
* http://armlinux.simtec.co.uk/
* Ben Dooks <ben@simtec.co.uk>
*
/* linux/include/asm-arm/arch-s3c2410/map.h
*
- * (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - Memory map definitions
*
*/
#ifndef __ASSEMBLY__
-#define S3C2410_ADDR(x) ((void __iomem *)0xF0000000 + (x))
+#define S3C2410_ADDR(x) ((void __iomem __force *)0xF0000000 + (x))
#else
#define S3C2410_ADDR(x) (0xF0000000 + (x))
#endif
#define S3C24XX_SZ_MEMCTRL SZ_1M
/* USB host controller */
-#define S3C24XX_VA_USBHOST S3C2410_ADDR(0x00200000)
#define S3C2400_PA_USBHOST (0x14200000)
#define S3C2410_PA_USBHOST (0x49000000)
#define S3C24XX_SZ_USBHOST SZ_1M
/* DMA controller */
-#define S3C24XX_VA_DMA S3C2410_ADDR(0x00300000)
#define S3C2400_PA_DMA (0x14600000)
#define S3C2410_PA_DMA (0x4B000000)
#define S3C24XX_SZ_DMA SZ_1M
/* Clock and Power management */
-#define S3C24XX_VA_CLKPWR S3C2410_ADDR(0x00400000)
+#define S3C24XX_VA_CLKPWR S3C2410_ADDR(0x00200000)
#define S3C2400_PA_CLKPWR (0x14800000)
#define S3C2410_PA_CLKPWR (0x4C000000)
#define S3C24XX_SZ_CLKPWR SZ_1M
/* LCD controller */
-#define S3C24XX_VA_LCD S3C2410_ADDR(0x00600000)
+#define S3C24XX_VA_LCD S3C2410_ADDR(0x00300000)
#define S3C2400_PA_LCD (0x14A00000)
#define S3C2410_PA_LCD (0x4D000000)
#define S3C24XX_SZ_LCD SZ_1M
/* NAND flash controller */
-#define S3C24XX_VA_NAND S3C2410_ADDR(0x00700000)
#define S3C2410_PA_NAND (0x4E000000)
#define S3C24XX_SZ_NAND SZ_1M
/* MMC controller - available on the S3C2400 */
-#define S3C2400_VA_MMC S3C2400_ADDR(0x00700000)
#define S3C2400_PA_MMC (0x15A00000)
#define S3C2400_SZ_MMC SZ_1M
/* UARTs */
-#define S3C24XX_VA_UART S3C2410_ADDR(0x00800000)
+#define S3C24XX_VA_UART S3C2410_ADDR(0x00400000)
#define S3C2400_PA_UART (0x15000000)
#define S3C2410_PA_UART (0x50000000)
#define S3C24XX_SZ_UART SZ_1M
/* Timers */
-#define S3C24XX_VA_TIMER S3C2410_ADDR(0x00900000)
+#define S3C24XX_VA_TIMER S3C2410_ADDR(0x00500000)
#define S3C2400_PA_TIMER (0x15100000)
#define S3C2410_PA_TIMER (0x51000000)
#define S3C24XX_SZ_TIMER SZ_1M
/* USB Device port */
-#define S3C24XX_VA_USBDEV S3C2410_ADDR(0x00A00000)
+#define S3C24XX_VA_USBDEV S3C2410_ADDR(0x00600000)
#define S3C2400_PA_USBDEV (0x15200140)
#define S3C2410_PA_USBDEV (0x52000000)
#define S3C24XX_SZ_USBDEV SZ_1M
/* Watchdog */
-#define S3C24XX_VA_WATCHDOG S3C2410_ADDR(0x00B00000)
+#define S3C24XX_VA_WATCHDOG S3C2410_ADDR(0x00700000)
#define S3C2400_PA_WATCHDOG (0x15300000)
#define S3C2410_PA_WATCHDOG (0x53000000)
#define S3C24XX_SZ_WATCHDOG SZ_1M
/* IIC hardware controller */
-#define S3C24XX_VA_IIC S3C2410_ADDR(0x00C00000)
#define S3C2400_PA_IIC (0x15400000)
#define S3C2410_PA_IIC (0x54000000)
#define S3C24XX_SZ_IIC SZ_1M
-#define VA_IIC_BASE (S3C24XX_VA_IIC)
-
/* IIS controller */
-#define S3C24XX_VA_IIS S3C2410_ADDR(0x00D00000)
#define S3C2400_PA_IIS (0x15508000)
#define S3C2410_PA_IIS (0x55000000)
#define S3C24XX_SZ_IIS SZ_1M
#define S3C24XX_SZ_GPIO SZ_1M
/* RTC */
-#define S3C24XX_VA_RTC S3C2410_ADDR(0x00F00000)
#define S3C2400_PA_RTC (0x15700040)
#define S3C2410_PA_RTC (0x57000000)
#define S3C24XX_SZ_RTC SZ_1M
/* ADC */
-#define S3C24XX_VA_ADC S3C2410_ADDR(0x01000000)
#define S3C2400_PA_ADC (0x15800000)
#define S3C2410_PA_ADC (0x58000000)
#define S3C24XX_SZ_ADC SZ_1M
/* SPI */
-#define S3C24XX_VA_SPI S3C2410_ADDR(0x01100000)
#define S3C2400_PA_SPI (0x15900000)
#define S3C2410_PA_SPI (0x59000000)
#define S3C24XX_SZ_SPI SZ_1M
/* SDI */
-#define S3C24XX_VA_SDI S3C2410_ADDR(0x01200000)
#define S3C2410_PA_SDI (0x5A000000)
#define S3C24XX_SZ_SDI SZ_1M
/* linux/include/asm-arm/arch-s3c2410/nand.h
*
- * (c) 2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - NAND device controller platfrom_device info
*
/* linux/include/asm-arm/arch-s3c2410/osiris-cpld.h
*
- * (c) 2005 Simtec Electronics
+ * Copyright (c) 2005 Simtec Electronics
* http://www.simtec.co.uk/products/
* Ben Dooks <ben@simtec.co.uk>
*
unsigned char hwport; /* hardware port number */
unsigned char unused;
unsigned short flags;
- unsigned long uart_flags; /* default uart flags */
+ upf_t uart_flags; /* default uart flags */
unsigned long ucon; /* value of ucon for port */
unsigned long ulcon; /* value of ulcon for port */
/* linux/include/asm-arm/arch-s3c2410/system.h
*
- * (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - System function defines and includes
*
/* linux/include/asm-arm/arch-s3c2410/timex.h
*
- * (c) 2003-2005 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003-2005 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - time parameters
*
/* linux/include/asm-arm/arch-s3c2410/uncompress.h
*
- * (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - uncompress code
*
#ifndef __ASM_ARCH_UNCOMPRESS_H
#define __ASM_ARCH_UNCOMPRESS_H
+typedef unsigned int upf_t; /* cannot include linux/serial_core.h */
/* defines for UART registers */
#include "asm/arch/regs-serial.h"
/* linux/include/asm-arm/arch-s3c2410/usb-control.h
*
- * (c) 2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* S3C2410 - usb port information
*
/* linux/include/asm-arm/arch-s3c2410/vr1000-cpld.h
*
- * (c) 2003 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* VR1000 - CPLD control constants
*
/* linux/include/asm-arm/arch-s3c2410/vr1000-irq.h
*
- * (c) 2003,2004 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003,2004 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* Machine VR1000 - IRQ Number definitions
*
/* linux/include/asm-arm/arch-s3c2410/vr1000-map.h
*
- * (c) 2003-2005 Simtec Electronics
- * Ben Dooks <ben@simtec.co.uk>
+ * Copyright (c) 2003-2005 Simtec Electronics
+ * Ben Dooks <ben@simtec.co.uk>
*
* Machine VR1000 - Memory map definitions
*
#define HWCAP_EDSP 128
#define HWCAP_JAVA 256
#define HWCAP_IWMMXT 512
+#define HWCAP_CRUNCH 1024
#ifdef __KERNEL__
#ifndef __ASSEMBLY__
#ifndef __ASSEMBLY__
#include <linux/linkage.h>
+#include <linux/irqflags.h>
struct thread_info;
struct task_struct;
#define cpu_is_xscale() 1
#endif
+extern unsigned long cr_no_alignment; /* defined in entry-armv.S */
+extern unsigned long cr_alignment; /* defined in entry-armv.S */
+
static inline unsigned int get_cr(void)
{
unsigned int val;
: : "r" (val) : "cc");
}
+#ifndef CONFIG_SMP
+extern void adjust_cr(unsigned long mask, unsigned long set);
+#endif
+
#define CPACC_FULL(n) (3 << (n * 2))
#define CPACC_SVC(n) (1 << (n * 2))
#define CPACC_DISABLE(n) (0 << (n * 2))
: : "r" (val) : "cc");
}
-extern unsigned long cr_no_alignment; /* defined in entry-armv.S */
-extern unsigned long cr_alignment; /* defined in entry-armv.S */
-
-#ifndef CONFIG_SMP
-static inline void adjust_cr(unsigned long mask, unsigned long set)
-{
- unsigned long flags, cr;
-
- mask &= ~CR_A;
-
- set &= mask;
-
- local_irq_save(flags);
-
- cr_no_alignment = (cr_no_alignment & ~mask) | set;
- cr_alignment = (cr_alignment & ~mask) | set;
-
- set_cr((get_cr() & ~mask) | set);
-
- local_irq_restore(flags);
-}
-#endif
-
#define UDBG_UNDEFINED (1 << 0)
#define UDBG_SYSCALL (1 << 1)
#define UDBG_BADABORT (1 << 2)
{
}
-#include <linux/irqflags.h>
-
#ifdef CONFIG_SMP
#define smp_mb() mb()
#define __NR_readlinkat (__NR_SYSCALL_BASE+332)
#define __NR_fchmodat (__NR_SYSCALL_BASE+333)
#define __NR_faccessat (__NR_SYSCALL_BASE+334)
+ /* 335 for pselect6 */
+ /* 336 for ppoll */
+#define __NR_unshare (__NR_SYSCALL_BASE+337)
+#define __NR_set_robust_list (__NR_SYSCALL_BASE+338)
+#define __NR_get_robust_list (__NR_SYSCALL_BASE+339)
+#define __NR_splice (__NR_SYSCALL_BASE+340)
+#define __NR_arm_sync_file_range (__NR_SYSCALL_BASE+341)
+#define __NR_tee (__NR_SYSCALL_BASE+342)
+#define __NR_vmsplice (__NR_SYSCALL_BASE+343)
+#define __NR_move_pages (__NR_SYSCALL_BASE+344)
+#define __NR_getcpu (__NR_SYSCALL_BASE+345)
+ /* 346 for epoll_pwait */
/*
* The following SWIs are ARM private.
extern long spu_sys_callback(struct spu_syscall_block *s);
/* syscalls implemented in spufs */
+struct file;
extern struct spufs_calls {
asmlinkage long (*create_thread)(const char __user *name,
unsigned int flags, mode_t mode);
* to object-id spufs file from user space and the notifer
* function can assume that spu->ctx is valid.
*/
+struct notifier_block;
int spu_switch_event_register(struct notifier_block * n);
int spu_switch_event_unregister(struct notifier_block * n);
size_t mmap_bytes;
char *buffer; /* vmallocated period */
size_t buffer_used; /* used length from period buffer */
+ struct mutex params_lock;
#ifdef CONFIG_SND_PCM_OSS_PLUGINS
struct snd_pcm_plugin *plugin_first;
struct snd_pcm_plugin *plugin_last;
/* include/version.h. Generated by alsa/ksync script. */
-#define CONFIG_SND_VERSION "1.0.13"
-#define CONFIG_SND_DATE " (Tue Nov 28 14:07:24 2006 UTC)"
+#define CONFIG_SND_VERSION "1.0.14rc1"
+#define CONFIG_SND_DATE " (Wed Dec 20 08:11:48 2006 UTC)"
int irq;
unsigned int device_id; /* PCI device ID */
- unsigned int rev; /* PCI revision */
+ unsigned char rev; /* PCI revision */
unsigned long reg_area_phys;
void __iomem *reg_area_virt;
struct resource *res_reg_area;
struct snd_kcontrol *spdif_pcm_ctl;
int mode_dup4ch;
int rear_opened;
- int rear_swap;
int spdif_opened;
struct {
u16 left;
int snd_ymfpci_pcm2(struct snd_ymfpci *chip, int device, struct snd_pcm **rpcm);
int snd_ymfpci_pcm_spdif(struct snd_ymfpci *chip, int device, struct snd_pcm **rpcm);
int snd_ymfpci_pcm_4ch(struct snd_ymfpci *chip, int device, struct snd_pcm **rpcm);
-int snd_ymfpci_mixer(struct snd_ymfpci *chip, int rear_switch, int rear_swap);
+int snd_ymfpci_mixer(struct snd_ymfpci *chip, int rear_switch);
int snd_ymfpci_timer(struct snd_ymfpci *chip, int device);
#endif /* __SOUND_YMFPCI_H */
#define __SND_AOA_CODEC_ONYX_H
#include <stddef.h>
#include <linux/i2c.h>
-#include <linux/i2c-dev.h>
#include <asm/pmac_low_i2c.h>
#include <asm/prom.h>
*/
#include <stddef.h>
#include <linux/i2c.h>
-#include <linux/i2c-dev.h>
#include <asm/pmac_low_i2c.h>
#include <asm/prom.h>
#include <linux/delay.h>
schedule();
remove_wait_queue(&ctl->change_sleep, &wait);
if (signal_pending(current))
- return result > 0 ? result : -ERESTARTSYS;
+ return -ERESTARTSYS;
spin_lock_irq(&ctl->read_lock);
}
kev = snd_kctl_event(ctl->events.next);
struct snd_mask sformat_mask;
struct snd_mask mask;
+ if (mutex_lock_interruptible(&runtime->oss.params_lock))
+ return -EINTR;
sw_params = kmalloc(sizeof(*sw_params), GFP_KERNEL);
params = kmalloc(sizeof(*params), GFP_KERNEL);
sparams = kmalloc(sizeof(*sparams), GFP_KERNEL);
kfree(sw_params);
kfree(params);
kfree(sparams);
+ mutex_unlock(&runtime->oss.params_lock);
return err;
}
if ((tmp = snd_pcm_oss_make_ready(substream)) < 0)
return tmp;
+ mutex_lock(&runtime->oss.params_lock);
while (bytes > 0) {
if (bytes < runtime->oss.period_bytes || runtime->oss.buffer_used > 0) {
tmp = bytes;
if (tmp + runtime->oss.buffer_used > runtime->oss.period_bytes)
tmp = runtime->oss.period_bytes - runtime->oss.buffer_used;
if (tmp > 0) {
- if (copy_from_user(runtime->oss.buffer + runtime->oss.buffer_used, buf, tmp))
- return xfer > 0 ? (snd_pcm_sframes_t)xfer : -EFAULT;
+ if (copy_from_user(runtime->oss.buffer + runtime->oss.buffer_used, buf, tmp)) {
+ tmp = -EFAULT;
+ goto err;
+ }
}
runtime->oss.buffer_used += tmp;
buf += tmp;
tmp = snd_pcm_oss_write2(substream, runtime->oss.buffer + runtime->oss.period_ptr,
runtime->oss.buffer_used - runtime->oss.period_ptr, 1);
if (tmp <= 0)
- return xfer > 0 ? (snd_pcm_sframes_t)xfer : tmp;
+ goto err;
runtime->oss.bytes += tmp;
runtime->oss.period_ptr += tmp;
runtime->oss.period_ptr %= runtime->oss.period_bytes;
if (runtime->oss.period_ptr == 0 ||
runtime->oss.period_ptr == runtime->oss.buffer_used)
runtime->oss.buffer_used = 0;
- else if ((substream->f_flags & O_NONBLOCK) != 0)
- return xfer > 0 ? xfer : -EAGAIN;
+ else if ((substream->f_flags & O_NONBLOCK) != 0) {
+ tmp = -EAGAIN;
+ goto err;
+ }
}
} else {
tmp = snd_pcm_oss_write2(substream,
(const char __force *)buf,
runtime->oss.period_bytes, 0);
if (tmp <= 0)
- return xfer > 0 ? (snd_pcm_sframes_t)xfer : tmp;
+ goto err;
runtime->oss.bytes += tmp;
buf += tmp;
bytes -= tmp;
break;
}
}
+ mutex_unlock(&runtime->oss.params_lock);
return xfer;
+
+ err:
+ mutex_unlock(&runtime->oss.params_lock);
+ return xfer > 0 ? (snd_pcm_sframes_t)xfer : tmp;
}
static ssize_t snd_pcm_oss_read2(struct snd_pcm_substream *substream, char *buf, size_t bytes, int in_kernel)
if ((tmp = snd_pcm_oss_make_ready(substream)) < 0)
return tmp;
+ mutex_lock(&runtime->oss.params_lock);
while (bytes > 0) {
if (bytes < runtime->oss.period_bytes || runtime->oss.buffer_used > 0) {
if (runtime->oss.buffer_used == 0) {
tmp = snd_pcm_oss_read2(substream, runtime->oss.buffer, runtime->oss.period_bytes, 1);
if (tmp <= 0)
- return xfer > 0 ? (snd_pcm_sframes_t)xfer : tmp;
+ goto err;
runtime->oss.bytes += tmp;
runtime->oss.period_ptr = tmp;
runtime->oss.buffer_used = tmp;
tmp = bytes;
if ((size_t) tmp > runtime->oss.buffer_used)
tmp = runtime->oss.buffer_used;
- if (copy_to_user(buf, runtime->oss.buffer + (runtime->oss.period_ptr - runtime->oss.buffer_used), tmp))
- return xfer > 0 ? (snd_pcm_sframes_t)xfer : -EFAULT;
+ if (copy_to_user(buf, runtime->oss.buffer + (runtime->oss.period_ptr - runtime->oss.buffer_used), tmp)) {
+ tmp = -EFAULT;
+ goto err;
+ }
buf += tmp;
bytes -= tmp;
xfer += tmp;
tmp = snd_pcm_oss_read2(substream, (char __force *)buf,
runtime->oss.period_bytes, 0);
if (tmp <= 0)
- return xfer > 0 ? (snd_pcm_sframes_t)xfer : tmp;
+ goto err;
runtime->oss.bytes += tmp;
buf += tmp;
bytes -= tmp;
xfer += tmp;
}
}
+ mutex_unlock(&runtime->oss.params_lock);
return xfer;
+
+ err:
+ mutex_unlock(&runtime->oss.params_lock);
+ return xfer > 0 ? (snd_pcm_sframes_t)xfer : tmp;
}
static int snd_pcm_oss_reset(struct snd_pcm_oss_file *pcm_oss_file)
return err;
format = snd_pcm_oss_format_from(runtime->oss.format);
width = snd_pcm_format_physical_width(format);
+ mutex_lock(&runtime->oss.params_lock);
if (runtime->oss.buffer_used > 0) {
#ifdef OSS_DEBUG
printk("sync: buffer_used\n");
runtime->oss.buffer + runtime->oss.buffer_used,
size);
err = snd_pcm_oss_sync1(substream, runtime->oss.period_bytes);
- if (err < 0)
+ if (err < 0) {
+ mutex_unlock(&runtime->oss.params_lock);
return err;
+ }
} else if (runtime->oss.period_ptr > 0) {
#ifdef OSS_DEBUG
printk("sync: period_ptr\n");
runtime->oss.buffer,
size * 8 / width);
err = snd_pcm_oss_sync1(substream, size);
- if (err < 0)
+ if (err < 0) {
+ mutex_unlock(&runtime->oss.params_lock);
return err;
+ }
}
/*
* The ALSA's period might be a bit large than OSS one.
snd_pcm_lib_writev(substream, buffers, size);
}
}
+ mutex_unlock(&runtime->oss.params_lock);
/*
* finish sync: drain the buffer
*/
runtime->oss.params = 1;
runtime->oss.trigger = 1;
runtime->oss.rate = 8000;
+ mutex_init(&runtime->oss.params_lock);
switch (SNDRV_MINOR_OSS_DEVICE(minor)) {
case SNDRV_MINOR_OSS_PCM_8:
runtime->oss.format = AFMT_U8;
err = snd_pcm_substream_proc_init(substream);
if (err < 0) {
snd_printk(KERN_ERR "Error in snd_pcm_stream_proc_init\n");
+ if (prev == NULL)
+ pstr->substream = NULL;
+ else
+ prev->next = NULL;
kfree(substream);
return err;
}
runtime->silence_filled -= frames;
if ((snd_pcm_sframes_t)runtime->silence_filled < 0) {
runtime->silence_filled = 0;
- runtime->silence_start = (ofs + frames) - runtime->buffer_size;
+ runtime->silence_start = new_hw_ptr;
} else {
- runtime->silence_start = ofs - runtime->silence_filled;
+ runtime->silence_start = ofs;
}
- if ((snd_pcm_sframes_t)runtime->silence_start < 0)
- runtime->silence_start += runtime->boundary;
}
frames = runtime->buffer_size - runtime->silence_filled;
}
snd_assert(frames <= runtime->buffer_size, return);
if (frames == 0)
return;
- ofs = (runtime->silence_start + runtime->silence_filled) % runtime->buffer_size;
+ ofs = runtime->silence_start % runtime->buffer_size;
while (frames > 0) {
transfer = ofs + frames > runtime->buffer_size ? runtime->buffer_size - ofs : frames;
if (runtime->access == SNDRV_PCM_ACCESS_RW_INTERLEAVED ||
struct snd_rawmidi_substream *substream;
int idx;
- INIT_LIST_HEAD(&stream->substreams);
for (idx = 0; idx < count; idx++) {
substream = kzalloc(sizeof(*substream), GFP_KERNEL);
if (substream == NULL) {
rmidi->device = device;
mutex_init(&rmidi->open_mutex);
init_waitqueue_head(&rmidi->open_wait);
+ INIT_LIST_HEAD(&rmidi->streams[SNDRV_RAWMIDI_STREAM_INPUT].substreams);
+ INIT_LIST_HEAD(&rmidi->streams[SNDRV_RAWMIDI_STREAM_OUTPUT].substreams);
+
if (id != NULL)
strlcpy(rmidi->id, id, sizeof(rmidi->id));
if ((err = snd_rawmidi_alloc_substreams(rmidi,
return len;
newlen = len;
if (size_aligned > 0)
- newlen = ((len + size_aligned - 1) / size_aligned) * size_aligned;
+ newlen = roundup(len, size_aligned);
if (count < newlen)
return -EAGAIN;
/* table entries are align to 32 */
#define SGBUF_TBL_ALIGN 32
-#define sgbuf_align_table(tbl) ((((tbl) + SGBUF_TBL_ALIGN - 1) / SGBUF_TBL_ALIGN) * SGBUF_TBL_ALIGN)
+#define sgbuf_align_table(tbl) ALIGN((tbl), SGBUF_TBL_ALIGN)
int snd_free_sgbuf_pages(struct snd_dma_buffer *dmab)
{
struct snd_gf1_mem_block *pblock;
unsigned int ptr1, ptr2;
- align--;
- if (w_16 && align < 1)
- align = 1;
+ if (w_16 && align < 2)
+ align = 2;
block->flags = w_16 ? SNDRV_GF1_MEM_BLOCK_16BIT : 0;
block->owner = SNDRV_GF1_MEM_OWNER_DRIVER;
block->share = 0;
if (pblock->next->ptr < boundary)
ptr2 = pblock->next->ptr;
}
- ptr1 = (pblock->ptr + pblock->size + align) & ~align;
+ ptr1 = ALIGN(pblock->ptr + pblock->size, align);
if (ptr1 >= ptr2)
continue;
size1 = ptr2 - ptr1;
chip->port = port;
if (request_irq(irq, irq_handler, hardware == SB_HW_ALS4000 ?
- IRQF_DISABLED | IRQF_SHARED : IRQF_DISABLED,
+ IRQF_SHARED : IRQF_DISABLED,
"SoundBlaster", (void *) chip)) {
snd_printk(KERN_ERR "sb: can't grab irq %d\n", irq);
snd_sbdsp_free(chip);
blocksize = max_blksize;
} else {
/* round to nearest 16-byte value */
- blocksize = ((length-written+7)&~0x7);
+ blocksize = ALIGN(length - written, 8);
}
if (snd_wavefront_cmd (dev, WFC_DOWNLOAD_BLOCK, NULL, NULL)) {
{ 0x434d4941, 0xffffffff, "CMI9738", patch_cm9738, NULL },
{ 0x434d4961, 0xffffffff, "CMI9739", patch_cm9739, NULL },
{ 0x434d4969, 0xffffffff, "CMI9780", patch_cm9780, NULL },
-{ 0x434d4978, 0xffffffff, "CMI9761", patch_cm9761, NULL },
-{ 0x434d4982, 0xffffffff, "CMI9761", patch_cm9761, NULL },
-{ 0x434d4983, 0xffffffff, "CMI9761", patch_cm9761, NULL },
+{ 0x434d4978, 0xffffffff, "CMI9761A", patch_cm9761, NULL },
+{ 0x434d4982, 0xffffffff, "CMI9761B", patch_cm9761, NULL },
+{ 0x434d4983, 0xffffffff, "CMI9761A+", patch_cm9761, NULL },
{ 0x43525900, 0xfffffff8, "CS4297", NULL, NULL },
{ 0x43525910, 0xfffffff8, "CS4297A", patch_cirrus_spdif, NULL },
{ 0x43525920, 0xfffffff8, "CS4298", patch_cirrus_spdif, NULL },
unsigned short old, new;
old = snd_ac97_read_cache(ac97, reg);
- new = (old & ~mask) | value;
+ new = (old & ~mask) | (value & mask);
change = old != new;
if (change) {
ac97->regs[reg] = new;
mutex_lock(&ac97->page_mutex);
old = ac97->spec.ad18xx.pcmreg[codec];
- new = (old & ~mask) | value;
+ new = (old & ~mask) | (value & mask);
change = old != new;
if (change) {
mutex_lock(&ac97->reg_mutex);
snd_ac97_write_cache(ac97, AC97_AD_CODEC_CFG, 0x0002); // ID1C
ac97->spec.ad18xx.codec_cfg[unchained_idx] = 0x0002;
if (cidx1 >= 0) {
- if (patch_ad1881_chained1(ac97, cidx1, 0x0006)) // SDIE | ID1C
+ if (cidx2 < 0)
+ patch_ad1881_chained1(ac97, cidx1, 0);
+ else if (patch_ad1881_chained1(ac97, cidx1, 0x0006)) // SDIE | ID1C
patch_ad1881_chained1(ac97, cidx2, 0);
else if (patch_ad1881_chained1(ac97, cidx2, 0x0006)) // SDIE | ID1C
patch_ad1881_chained1(ac97, cidx1, 0);
else { /* ALC655 */
if (ac97->subsystem_vendor == 0x1462 &&
(ac97->subsystem_device == 0x0131 || /* MSI S270 laptop */
- ac97->subsystem_device == 0x0161)) /* LG K1 Express */
+ ac97->subsystem_device == 0x0161 || /* LG K1 Express */
+ ac97->subsystem_device == 0x0351)) /* MSI L725 laptop */
val &= ~(1 << 1); /* Pin 47 is EAPD (for internal speaker) */
else
val |= (1 << 1); /* Pin 47 is spdif input pin */
synchronize_irq(chip->irq);
if (chip->irq >= 0)
- free_irq(chip->irq, (void*)chip);
+ free_irq(chip->irq, chip);
skip_hw:
if (chip->iobase)
spin_lock_init(&chip->lock); /* only now can we call ad1889_free */
if (request_irq(pci->irq, snd_ad1889_interrupt,
- IRQF_DISABLED|IRQF_SHARED, card->driver, (void*)chip)) {
+ IRQF_SHARED, card->driver, chip)) {
printk(KERN_ERR PFX "cannot obtain IRQ %d\n", pci->irq);
snd_ad1889_free(chip);
return -EBUSY;
snd_ali_disable_address_interrupt(codec);
if (codec->irq >= 0) {
synchronize_irq(codec->irq);
- free_irq(codec->irq, (void *)codec);
+ free_irq(codec->irq, codec);
}
if (codec->port)
pci_release_regions(codec->pci);
return err;
codec->port = pci_resource_start(codec->pci, 0);
- if (request_irq(codec->pci->irq, snd_ali_card_interrupt, IRQF_DISABLED|IRQF_SHARED, "ALI 5451", (void *)codec)) {
+ if (request_irq(codec->pci->irq, snd_ali_card_interrupt,
+ IRQF_SHARED, "ALI 5451", codec)) {
snd_printk(KERN_ERR "Unable to request irq.\n");
return -EBUSY;
}
snd_als300_dbgcallenter();
snd_als300_set_irq_flag(chip, IRQ_DISABLE);
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
pci_release_regions(chip->pci);
pci_disable_device(chip->pci);
kfree(chip);
else
irq_handler = snd_als300_interrupt;
- if (request_irq(pci->irq, irq_handler, IRQF_DISABLED|IRQF_SHARED,
- card->shortname, (void *)chip)) {
+ if (request_irq(pci->irq, irq_handler, IRQF_SHARED,
+ card->shortname, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_als300_free(chip);
return -EBUSY;
return -EIO;
}
- if (request_irq(pci->irq, snd_atiixp_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_atiixp_interrupt, IRQF_SHARED,
card->shortname, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_atiixp_free(chip);
return -EIO;
}
- if (request_irq(pci->irq, snd_atiixp_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_atiixp_interrupt, IRQF_SHARED,
card->shortname, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_atiixp_free(chip);
}
if ((err = request_irq(pci->irq, vortex_interrupt,
- IRQF_DISABLED | IRQF_SHARED, CARD_NAME_SHORT,
+ IRQF_SHARED, CARD_NAME_SHORT,
chip)) != 0) {
printk(KERN_ERR "cannot grab irq\n");
goto irq_out;
__end_hw:
snd_azf3328_free_joystick(chip);
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
pci_release_regions(chip->pci);
pci_disable_device(chip->pci);
chip->synth_port = pci_resource_start(pci, 3);
chip->mixer_port = pci_resource_start(pci, 4);
- if (request_irq(pci->irq, snd_azf3328_interrupt, IRQF_DISABLED|IRQF_SHARED, card->shortname, (void *)chip)) {
+ if (request_irq(pci->irq, snd_azf3328_interrupt,
+ IRQF_SHARED, card->shortname, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
err = -EBUSY;
goto out_err;
SNDRV_DMA_TYPE_DEV_SG,
snd_dma_pci_data(chip->pci),
128 * 1024,
- (255 * 4092 + 1023) & ~1023);
+ ALIGN(255 * 4092, 1024));
}
static int __devinit snd_bt87x_create(struct snd_card *card,
snd_bt87x_writel(chip, REG_INT_MASK, 0);
snd_bt87x_writel(chip, REG_INT_STAT, MY_INTERRUPTS);
- if (request_irq(pci->irq, snd_bt87x_interrupt, IRQF_DISABLED | IRQF_SHARED,
+ if (request_irq(pci->irq, snd_bt87x_interrupt, IRQF_SHARED,
"Bt87x audio", chip)) {
snd_bt87x_free(chip);
snd_printk(KERN_ERR "cannot grab irq\n");
struct resource *res_port;
int irq;
- unsigned int revision; /* chip revision */
+ unsigned char revision; /* chip revision */
unsigned int serial; /* serial number */
unsigned short model; /* subsystem id */
static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX;
static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR;
static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP;
+static uint subsystem[SNDRV_CARDS]; /* Force card subsystem model */
module_param_array(index, int, NULL, 0444);
MODULE_PARM_DESC(index, "Index value for the CA0106 soundcard.");
MODULE_PARM_DESC(id, "ID string for the CA0106 soundcard.");
module_param_array(enable, bool, NULL, 0444);
MODULE_PARM_DESC(enable, "Enable the CA0106 soundcard.");
+module_param_array(subsystem, uint, NULL, 0444);
+MODULE_PARM_DESC(subsystem, "Force card subsystem model.");
#include "ca0106.h"
.gpio_type = 1,
.i2c_adc = 1,
.spi_dac = 1 } ,
+ /* New Audigy LS. Has a different DAC. */
+ /* SB0570:
+ * CTRL:CA0106-DAT
+ * ADC: WM8775EDS
+ * DAC: WM8768GEDS
+ */
+ { .serial = 0x10111102,
+ .name = "Audigy SE OEM [SB0570a]",
+ .gpio_type = 1,
+ .i2c_adc = 1,
+ .spi_dac = 1 } ,
/* MSI K8N Diamond Motherboard with onboard SB Live 24bit without AC97 */
/* SB0438
* CTRL:CA0106-DAT
// release the irq
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
pci_disable_device(chip->pci);
kfree(chip);
return 0;
{ 0x15, ADC_MUX_LINEIN }, /* ADC Mixer control */
};
-static int __devinit snd_ca0106_create(struct snd_card *card,
+static int __devinit snd_ca0106_create(int dev, struct snd_card *card,
struct pci_dev *pci,
struct snd_ca0106 **rchip)
{
}
if (request_irq(pci->irq, snd_ca0106_interrupt,
- IRQF_DISABLED|IRQF_SHARED, "snd_ca0106",
- (void *)chip)) {
+ IRQF_SHARED, "snd_ca0106", chip)) {
snd_ca0106_free(chip);
printk(KERN_ERR "cannot grab irq\n");
return -EBUSY;
pci_set_master(pci);
/* read revision & serial */
- pci_read_config_byte(pci, PCI_REVISION_ID, (char *)&chip->revision);
+ pci_read_config_byte(pci, PCI_REVISION_ID, &chip->revision);
pci_read_config_dword(pci, PCI_SUBSYSTEM_VENDOR_ID, &chip->serial);
pci_read_config_word(pci, PCI_SUBSYSTEM_ID, &chip->model);
#if 1
- printk(KERN_INFO "Model %04x Rev %08x Serial %08x\n", chip->model,
+ printk(KERN_INFO "snd-ca0106: Model %04x Rev %08x Serial %08x\n", chip->model,
chip->revision, chip->serial);
#endif
strcpy(card->driver, "CA0106");
strcpy(card->shortname, "CA0106");
for (c = ca0106_chip_details; c->serial; c++) {
- if (c->serial == chip->serial)
+ if (subsystem[dev]) {
+ if (c->serial == subsystem[dev])
+ break;
+ } else if (c->serial == chip->serial)
break;
}
chip->details = c;
+ if (subsystem[dev]) {
+ printk(KERN_INFO "snd-ca0106: Sound card name=%s, subsystem=0x%x. Forced to subsystem=0x%x\n",
+ c->name, chip->serial, subsystem[dev]);
+ }
+
sprintf(card->longname, "%s at 0x%lx irq %i",
c->name, chip->port, chip->irq);
if (card == NULL)
return -ENOMEM;
- if ((err = snd_ca0106_create(card, pci, &chip)) < 0) {
+ if ((err = snd_ca0106_create(dev, card, pci, &chip)) < 0) {
snd_card_free(card);
return err;
}
cm->iobase = pci_resource_start(pci, 0);
if (request_irq(pci->irq, snd_cmipci_interrupt,
- IRQF_DISABLED|IRQF_SHARED, card->driver, cm)) {
+ IRQF_SHARED, card->driver, cm)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_cmipci_free(cm);
return -EBUSY;
return -ENOMEM;
}
- if (request_irq(pci->irq, snd_cs4281_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_cs4281_interrupt, IRQF_SHARED,
"CS4281", chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_cs4281_free(chip);
}
}
- if (request_irq(pci->irq, snd_cs46xx_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_cs46xx_interrupt, IRQF_SHARED,
"CS46XX", chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_cs46xx_free(chip);
cs5535au->port = pci_resource_start(pci, 0);
if (request_irq(pci->irq, snd_cs5535audio_interrupt,
- IRQF_DISABLED|IRQF_SHARED, "CS5535 Audio", cs5535au)) {
+ IRQF_SHARED, "CS5535 Audio", cs5535au)) {
snd_printk("unable to grab IRQ %d\n", pci->irq);
err = -EBUSY;
goto sndfail;
DE_INIT(("Stopped.\n"));
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
if (chip->dsp_registers)
iounmap(chip->dsp_registers);
chip->dsp_registers = (volatile u32 __iomem *)
ioremap_nocache(chip->dsp_registers_phys, sz);
- if (request_irq(pci->irq, snd_echo_interrupt, IRQF_DISABLED | IRQF_SHARED,
- ECHOCARD_NAME, (void *)chip)) {
+ if (request_irq(pci->irq, snd_echo_interrupt, IRQF_SHARED,
+ ECHOCARD_NAME, chip)) {
snd_echo_free(chip);
snd_printk(KERN_ERR "cannot grab irq\n");
return -EBUSY;
free_pm_buffer(emu);
#endif
if (emu->irq >= 0)
- free_irq(emu->irq, (void *)emu);
+ free_irq(emu->irq, emu);
if (emu->port)
pci_release_regions(emu->pci);
if (emu->card_capabilities->ca0151_chip) /* P16V */
}
emu->port = pci_resource_start(pci, 0);
- if (request_irq(pci->irq, snd_emu10k1_interrupt, IRQF_DISABLED|IRQF_SHARED, "EMU10K1", (void *)emu)) {
+ if (request_irq(pci->irq, snd_emu10k1_interrupt, IRQF_SHARED,
+ "EMU10K1", emu)) {
err = -EBUSY;
goto error;
}
struct resource *res_port;
int irq;
- unsigned int revision; /* chip revision */
+ unsigned char revision; /* chip revision */
unsigned int serial; /* serial number */
unsigned short model; /* subsystem id */
// release the irq
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
// release the DMA
if (chip->dma_buffer.area) {
}
if (request_irq(pci->irq, snd_emu10k1x_interrupt,
- IRQF_DISABLED|IRQF_SHARED, "EMU10K1X",
- (void *)chip)) {
+ IRQF_SHARED, "EMU10K1X", chip)) {
snd_printk(KERN_ERR "emu10k1x: cannot grab irq %d\n", pci->irq);
snd_emu10k1x_free(chip);
return -EBUSY;
pci_set_master(pci);
/* read revision & serial */
- pci_read_config_byte(pci, PCI_REVISION_ID, (char *)&chip->revision);
+ pci_read_config_byte(pci, PCI_REVISION_ID, &chip->revision);
pci_read_config_dword(pci, PCI_SUBSYSTEM_VENDOR_ID, &chip->serial);
pci_read_config_word(pci, PCI_SUBSYSTEM_ID, &chip->model);
snd_printk(KERN_INFO "Model %04x Rev %08x Serial %08x\n", chip->model,
return err;
}
ensoniq->port = pci_resource_start(pci, 0);
- if (request_irq(pci->irq, snd_audiopci_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_audiopci_interrupt, IRQF_SHARED,
"Ensoniq AudioPCI", ensoniq)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_ensoniq_free(ensoniq);
}
if (request_irq(pci->irq, snd_es1938_interrupt,
- IRQF_DISABLED|IRQF_SHARED, "ES1938", chip)) {
+ IRQF_SHARED, "ES1938", chip)) {
printk(KERN_ERR "es1938: unable to grab IRQ %d, "
"disabling device\n", pci->irq);
snd_card_disconnect(card);
chip->vc_port = pci_resource_start(pci, 2);
chip->mpu_port = pci_resource_start(pci, 3);
chip->game_port = pci_resource_start(pci, 4);
- if (request_irq(pci->irq, snd_es1938_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_es1938_interrupt, IRQF_SHARED,
"ES1938", chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_es1938_free(chip);
struct esm_memory *buf;
struct list_head *p;
- size = ((size + ESM_MEM_ALIGN - 1) / ESM_MEM_ALIGN) * ESM_MEM_ALIGN;
+ size = ALIGN(size, ESM_MEM_ALIGN);
mutex_lock(&chip->memory_mutex);
list_for_each(p, &chip->buf_list) {
buf = list_entry(p, struct esm_memory, list);
}
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
snd_es1968_free_gameport(chip);
chip->master_switch = NULL;
chip->master_volume = NULL;
return err;
}
chip->io_port = pci_resource_start(pci, 0);
- if (request_irq(pci->irq, snd_es1968_interrupt, IRQF_DISABLED|IRQF_SHARED,
- "ESS Maestro", (void*)chip)) {
+ if (request_irq(pci->irq, snd_es1968_interrupt, IRQF_SHARED,
+ "ESS Maestro", chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_es1968_free(chip);
return -EBUSY;
}
chip->port = pci_resource_start(pci, 0);
if ((tea575x_tuner & 0x0010) == 0) {
- if (request_irq(pci->irq, snd_fm801_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_fm801_interrupt, IRQF_SHARED,
"FM801", chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", chip->irq);
snd_fm801_free(chip);
{ 176400, SNDRV_PCM_RATE_176400, 0x5800 },/* 4 x 44 */
{ 192000, SNDRV_PCM_RATE_192000, 0x1800 }, /* 4 x 48 */
- /* not autodetected value */
- { 9600, SNDRV_PCM_RATE_KNOT, 0x0400 }, /* 1/5 x 48 */
-
{ 0 } /* terminator */
};
static int azx_acquire_irq(struct azx *chip, int do_disconnect)
{
- if (request_irq(chip->pci->irq, azx_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(chip->pci->irq, azx_interrupt,
+ chip->msi ? 0 : IRQF_SHARED,
"HDA Intel", chip)) {
printk(KERN_ERR "hda-intel: unable to grab IRQ %d, "
"disabling device\n", chip->pci->irq);
if (names[wid_value])
return names[wid_value];
else
- return "UNKOWN Widget";
+ return "UNKNOWN Widget";
}
static void print_amp_caps(struct snd_info_buffer *buffer,
snd_iprintf(buffer, "\n");
}
+static void print_pcm_rates(struct snd_info_buffer *buffer, unsigned int pcm)
+{
+ static unsigned int rates[] = {
+ 8000, 11025, 16000, 22050, 32000, 44100, 48000, 88200,
+ 96000, 176400, 192000, 384000
+ };
+ int i;
+
+ pcm &= AC_SUPPCM_RATES;
+ snd_iprintf(buffer, " rates [0x%x]:", pcm);
+ for (i = 0; i < ARRAY_SIZE(rates); i++)
+ if (pcm & (1 << i))
+ snd_iprintf(buffer, " %d", rates[i]);
+ snd_iprintf(buffer, "\n");
+}
+
+static void print_pcm_bits(struct snd_info_buffer *buffer, unsigned int pcm)
+{
+ static unsigned int bits[] = { 8, 16, 20, 24, 32 };
+ int i;
+
+ pcm = (pcm >> 16) & 0xff;
+ snd_iprintf(buffer, " bits [0x%x]:", pcm);
+ for (i = 0; i < ARRAY_SIZE(bits); i++)
+ if (pcm & (1 << i))
+ snd_iprintf(buffer, " %d", bits[i]);
+ snd_iprintf(buffer, "\n");
+}
+
+static void print_pcm_formats(struct snd_info_buffer *buffer,
+ unsigned int streams)
+{
+ snd_iprintf(buffer, " formats [0x%x]:", streams & 0xf);
+ if (streams & AC_SUPFMT_PCM)
+ snd_iprintf(buffer, " PCM");
+ if (streams & AC_SUPFMT_FLOAT32)
+ snd_iprintf(buffer, " FLOAT");
+ if (streams & AC_SUPFMT_AC3)
+ snd_iprintf(buffer, " AC3");
+ snd_iprintf(buffer, "\n");
+}
+
static void print_pcm_caps(struct snd_info_buffer *buffer,
struct hda_codec *codec, hda_nid_t nid)
{
snd_iprintf(buffer, "N/A\n");
return;
}
- snd_iprintf(buffer, "rates 0x%03x, bits 0x%02x, types 0x%x\n",
- pcm & AC_SUPPCM_RATES, (pcm >> 16) & 0xff, stream & 0xf);
+ print_pcm_rates(buffer, pcm);
+ print_pcm_bits(buffer, pcm);
+ print_pcm_formats(buffer, stream);
}
static const char *get_jack_location(u32 cfg)
snd_iprintf(buffer, "Revision Id: 0x%x\n", codec->revision_id);
if (! codec->afg)
return;
- snd_iprintf(buffer, "Default PCM: ");
+ snd_iprintf(buffer, "Default PCM:\n");
print_pcm_caps(buffer, codec, codec->afg);
snd_iprintf(buffer, "Default Amp-In caps: ");
print_amp_caps(buffer, codec, codec->afg, HDA_INPUT);
if ((wid_type == AC_WID_AUD_OUT || wid_type == AC_WID_AUD_IN) &&
(wid_caps & AC_WCAP_FORMAT_OVRD)) {
- snd_iprintf(buffer, " PCM: ");
+ snd_iprintf(buffer, " PCM:\n");
print_pcm_caps(buffer, codec, nid);
}
{ .modelname = "3stack", .config = AD1986A_3STACK },
{ .pci_subvendor = 0x10de, .pci_subdevice = 0xcb84,
.config = AD1986A_3STACK }, /* ASUS A8N-VM CSM */
+ { .pci_subvendor = 0x1043, .pci_subdevice = 0x817f,
+ .config = AD1986A_3STACK }, /* ASUS P5P-L2 */
{ .pci_subvendor = 0x1043, .pci_subdevice = 0x81b3,
.config = AD1986A_3STACK }, /* ASUS P5RD2-VM / P5GPL-X SE */
{ .pci_subvendor = 0x1043, .pci_subdevice = 0x81cb,
{ .pci_subvendor = 0x144d, .pci_subdevice = 0xc024,
.config = AD1986A_LAPTOP_EAPD }, /* Samsung R65-T2300 Charis */
{ .pci_subvendor = 0x144d, .pci_subdevice = 0xc026,
- .config = AD1986A_LAPTOP_EAPD }, /* Samsung X10-T2300 Culesa */
+ .config = AD1986A_LAPTOP_EAPD }, /* Samsung X11-T2300 Culesa */
{ .pci_subvendor = 0x1043, .pci_subdevice = 0x1153,
.config = AD1986A_LAPTOP_EAPD }, /* ASUS M9 */
{ .pci_subvendor = 0x1043, .pci_subdevice = 0x1213,
.config = AD1986A_LAPTOP_EAPD }, /* ASUS U5F */
{ .pci_subvendor = 0x1043, .pci_subdevice = 0x1297,
.config = AD1986A_LAPTOP_EAPD }, /* ASUS Z62F */
+ { .pci_subvendor = 0x1043, .pci_subdevice = 0x12b3,
+ .config = AD1986A_LAPTOP_EAPD }, /* ASUS V1j */
{ .pci_subvendor = 0x103c, .pci_subdevice = 0x30af,
.config = AD1986A_LAPTOP_EAPD }, /* HP Compaq Presario B2800 */
{ .pci_subvendor = 0x17aa, .pci_subdevice = 0x2066,
int err = snd_hda_ch_mode_put(codec, ucontrol, spec->channel_mode,
spec->num_channel_mode,
&spec->multiout.max_channels);
- if (! err && spec->need_dac_fix)
+ if (err >= 0 && spec->need_dac_fix)
spec->multiout.num_dacs = spec->multiout.max_channels / 2;
return err;
}
int err = snd_hda_ch_mode_put(codec, ucontrol, spec->channel_mode,
spec->num_channel_mode,
&spec->multiout.max_channels);
- if (! err && spec->need_dac_fix)
+ if (err >= 0 && spec->need_dac_fix)
spec->multiout.num_dacs = spec->multiout.max_channels / 2;
return err;
}
{ .modelname = "hp-bpc", .config = ALC262_HP_BPC },
{ .pci_subvendor = 0x103c, .pci_subdevice = 0x280c,
.config = ALC262_HP_BPC }, /* xw4400 */
+ { .pci_subvendor = 0x103c, .pci_subdevice = 0x2801,
+ .config = ALC262_HP_BPC }, /* q965 */
{ .pci_subvendor = 0x103c, .pci_subdevice = 0x3014,
.config = ALC262_HP_BPC }, /* xw6400 */
{ .pci_subvendor = 0x103c, .pci_subdevice = 0x3015,
if((val&SI3054_MEI_READY) != SI3054_MEI_READY) {
snd_printk(KERN_ERR "si3054: cannot initialize. EXT MID = %04x\n", val);
- return -EACCES;
+ /* let's pray that this is no fatal error */
+ /* return -EACCES; */
}
SET_REG(codec, SI3054_GPIO_POLARITY, 0xffff);
ice->dmapath_port = pci_resource_start(pci, 2);
ice->profi_port = pci_resource_start(pci, 3);
- if (request_irq(pci->irq, snd_ice1712_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_ice1712_interrupt, IRQF_SHARED,
"ICE1712", ice)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_ice1712_free(ice);
ice->profi_port = pci_resource_start(pci, 1);
if (request_irq(pci->irq, snd_vt1724_interrupt,
- IRQF_DISABLED|IRQF_SHARED, "ICE1724", ice)) {
+ IRQF_SHARED, "ICE1724", ice)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_vt1724_free(ice);
return -EIO;
}
pci_set_master(pci);
if (request_irq(pci->irq, snd_intel8x0_interrupt,
- IRQF_DISABLED|IRQF_SHARED, card->shortname, chip)) {
+ IRQF_SHARED, card->shortname, chip)) {
printk(KERN_ERR "intel8x0: unable to grab IRQ %d, "
"disabling device\n", pci->irq);
snd_card_disconnect(card);
/* request irq after initializaing int_sta_mask, etc */
if (request_irq(pci->irq, snd_intel8x0_interrupt,
- IRQF_DISABLED|IRQF_SHARED, card->shortname, chip)) {
+ IRQF_SHARED, card->shortname, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_intel8x0_free(chip);
return -EBUSY;
}
pci_set_master(pci);
if (request_irq(pci->irq, snd_intel8x0_interrupt,
- IRQF_DISABLED|IRQF_SHARED, card->shortname, chip)) {
+ IRQF_SHARED, card->shortname, chip)) {
printk(KERN_ERR "intel8x0m: unable to grab IRQ %d, "
"disabling device\n", pci->irq);
snd_card_disconnect(card);
}
port_inited:
- if (request_irq(pci->irq, snd_intel8x0_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_intel8x0_interrupt, IRQF_SHARED,
card->shortname, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_intel8x0_free(chip);
}
err = request_irq(pci->irq, snd_korg1212_interrupt,
- IRQF_DISABLED|IRQF_SHARED,
+ IRQF_SHARED,
"korg1212", korg1212);
if (err) {
* shifted list address is aligned.
* list address = (mem address >> 1) >> 7;
*/
- data_bytes = (data_bytes + 255) & ~255;
+ data_bytes = ALIGN(data_bytes, 256);
address = 0x1100 + ((data_bytes/2) * index);
if ((address + (data_bytes/2)) >= 0x1c00) {
tasklet_init(&chip->hwvol_tq, snd_m3_update_hw_volume, (unsigned long)chip);
- if (request_irq(pci->irq, snd_m3_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_m3_interrupt, IRQF_SHARED,
card->driver, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_m3_free(chip);
/* release irq */
if (mgr->irq >= 0)
- free_irq(mgr->irq, (void *)mgr);
+ free_irq(mgr->irq, mgr);
/* reset board if some firmware was loaded */
if(mgr->dsp_loaded) {
pci_resource_len(pci, i));
}
- if (request_irq(pci->irq, snd_mixart_interrupt, IRQF_DISABLED|IRQF_SHARED, CARD_NAME, (void *)mgr)) {
+ if (request_irq(pci->irq, snd_mixart_interrupt, IRQF_SHARED,
+ CARD_NAME, mgr)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_mixart_free(mgr);
return -EBUSY;
{
mutex_lock(&chip->irq_mutex);
if (chip->irq < 0) {
- if (request_irq(chip->pci->irq, chip->interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(chip->pci->irq, chip->interrupt, IRQF_SHARED,
chip->card->driver, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", chip->pci->irq);
mutex_unlock(&chip->irq_mutex);
mgr->pci = pci;
mgr->irq = -1;
- if (request_irq(pci->irq, pcxhr_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, pcxhr_interrupt, IRQF_SHARED,
card_name, mgr)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
pcxhr_free(mgr);
hwport = (struct riptideport *)chip->port;
UNSET_AIE(hwport);
- if (request_irq
- (pci->irq, snd_riptide_interrupt, IRQF_DISABLED | IRQF_SHARED,
- "RIPTIDE", chip)) {
+ if (request_irq(pci->irq, snd_riptide_interrupt, IRQF_SHARED,
+ "RIPTIDE", chip)) {
snd_printk(KERN_ERR "Riptide: unable to grab IRQ %d\n",
pci->irq);
snd_riptide_free(chip);
return -ENOMEM;
}
- if (request_irq(pci->irq, snd_rme32_interrupt, IRQF_DISABLED | IRQF_SHARED, "RME32", (void *) rme32)) {
+ if (request_irq(pci->irq, snd_rme32_interrupt, IRQF_SHARED,
+ "RME32", rme32)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
return -EBUSY;
}
return -ENOMEM;
}
- if (request_irq(pci->irq, snd_rme96_interrupt, IRQF_DISABLED|IRQF_SHARED, "RME96", (void *)rme96)) {
+ if (request_irq(pci->irq, snd_rme96_interrupt, IRQF_SHARED,
+ "RME96", rme96)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
return -EBUSY;
}
/* Align to bus-space 64K boundary */
- cb_bus = (hdsp->capture_dma_buf.addr + 0xFFFF) & ~0xFFFFl;
- pb_bus = (hdsp->playback_dma_buf.addr + 0xFFFF) & ~0xFFFFl;
+ cb_bus = ALIGN(hdsp->capture_dma_buf.addr, 0x10000ul);
+ pb_bus = ALIGN(hdsp->playback_dma_buf.addr, 0x10000ul);
/* Tell the card where it is */
return -EBUSY;
}
- if (request_irq(pci->irq, snd_hdsp_interrupt, IRQF_DISABLED|IRQF_SHARED, "hdsp", (void *)hdsp)) {
+ if (request_irq(pci->irq, snd_hdsp_interrupt, IRQF_SHARED,
+ "hdsp", hdsp)) {
snd_printk(KERN_ERR "Hammerfall-DSP: unable to use IRQ %d\n", pci->irq);
return -EBUSY;
}
hdsp->irq = pci->irq;
- hdsp->precise_ptr = 1;
+ hdsp->precise_ptr = 0;
hdsp->use_midi_tasklet = 1;
if ((err = snd_hdsp_initialize_memory(hdsp)) < 0)
hdspm->port + io_extent - 1);
if (request_irq(pci->irq, snd_hdspm_interrupt,
- IRQF_DISABLED | IRQF_SHARED, "hdspm",
- (void *) hdspm)) {
+ IRQF_SHARED, "hdspm", hdspm)) {
snd_printk(KERN_ERR "HDSPM: unable to use IRQ %d\n", pci->irq);
return -EBUSY;
}
/* Align to bus-space 64K boundary */
- cb_bus = (rme9652->capture_dma_buf.addr + 0xFFFF) & ~0xFFFFl;
- pb_bus = (rme9652->playback_dma_buf.addr + 0xFFFF) & ~0xFFFFl;
+ cb_bus = ALIGN(rme9652->capture_dma_buf.addr, 0x10000ul);
+ pb_bus = ALIGN(rme9652->playback_dma_buf.addr, 0x10000ul);
/* Tell the card where it is */
return -EBUSY;
}
- if (request_irq(pci->irq, snd_rme9652_interrupt, IRQF_DISABLED|IRQF_SHARED, "rme9652", (void *)rme9652)) {
+ if (request_irq(pci->irq, snd_rme9652_interrupt, IRQF_SHARED,
+ "rme9652", rme9652)) {
snd_printk(KERN_ERR "unable to request IRQ %d\n", pci->irq);
return -EBUSY;
}
pci_write_config_dword(sonic->pci, 0x40, sonic->dmaa_port);
pci_write_config_dword(sonic->pci, 0x48, sonic->dmac_port);
if (sonic->irq >= 0)
- free_irq(sonic->irq, (void *)sonic);
+ free_irq(sonic->irq, sonic);
release_and_free_resource(sonic->res_dmaa);
release_and_free_resource(sonic->res_dmac);
pci_release_regions(sonic->pci);
sonic->midi_port = pci_resource_start(pci, 3);
sonic->game_port = pci_resource_start(pci, 4);
- if (request_irq(pci->irq, snd_sonicvibes_interrupt, IRQF_DISABLED|IRQF_SHARED, "S3 SonicVibes", (void *)sonic)) {
+ if (request_irq(pci->irq, snd_sonicvibes_interrupt, IRQF_SHARED,
+ "S3 SonicVibes", sonic)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_sonicvibes_free(sonic);
return -EBUSY;
snd_printk(KERN_ERR "trident: unable to allocate TLB buffer\n");
return -ENOMEM;
}
- trident->tlb.entries = (unsigned int*)(((unsigned long)trident->tlb.buffer.area + SNDRV_TRIDENT_MAX_PAGES * 4 - 1) & ~(SNDRV_TRIDENT_MAX_PAGES * 4 - 1));
- trident->tlb.entries_dmaaddr = (trident->tlb.buffer.addr + SNDRV_TRIDENT_MAX_PAGES * 4 - 1) & ~(SNDRV_TRIDENT_MAX_PAGES * 4 - 1);
+ trident->tlb.entries = (unsigned int*)ALIGN((unsigned long)trident->tlb.buffer.area, SNDRV_TRIDENT_MAX_PAGES * 4);
+ trident->tlb.entries_dmaaddr = ALIGN(trident->tlb.buffer.addr, SNDRV_TRIDENT_MAX_PAGES * 4);
/* allocate shadow TLB page table (virtual addresses) */
trident->tlb.shadow_entries = vmalloc(SNDRV_TRIDENT_MAX_PAGES*sizeof(unsigned long));
if (trident->tlb.shadow_entries == NULL) {
}
trident->port = pci_resource_start(pci, 0);
- if (request_irq(pci->irq, snd_trident_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_trident_interrupt, IRQF_SHARED,
"Trident Audio", trident)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_trident_free(trident);
if (request_irq(pci->irq,
chip_type == TYPE_VIA8233 ?
snd_via8233_interrupt : snd_via686_interrupt,
- IRQF_DISABLED|IRQF_SHARED,
+ IRQF_SHARED,
card->driver, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_via82xx_free(chip);
static int __devinit check_dxs_list(struct pci_dev *pci, int revision)
{
- static struct dxs_whitelist whitelist[] = {
+ static struct dxs_whitelist whitelist[] __devinitdata = {
{ .subvendor = 0x1005, .subdevice = 0x4710, .action = VIA_DXS_ENABLE }, /* Avance Logic Mobo */
{ .subvendor = 0x1019, .subdevice = 0x0996, .action = VIA_DXS_48K },
{ .subvendor = 0x1019, .subdevice = 0x0a81, .action = VIA_DXS_NO_VRA }, /* ECS K7VTA3 v8.0 */
{ .subvendor = 0x4005, .subdevice = 0x4710, .action = VIA_DXS_SRC }, /* MSI K7T266 Pro2 (MS-6380 V2.0) BIOS 3.7 */
{ } /* terminator */
};
- struct dxs_whitelist *w;
+ const struct dxs_whitelist *w;
unsigned short subsystem_vendor;
unsigned short subsystem_device;
return err;
}
chip->port = pci_resource_start(pci, 0);
- if (request_irq(pci->irq, snd_via82xx_interrupt, IRQF_DISABLED|IRQF_SHARED,
+ if (request_irq(pci->irq, snd_via82xx_interrupt, IRQF_SHARED,
card->driver, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_via82xx_free(chip);
for (i = 0; i < 2; i++)
vx->port[i] = pci_resource_start(pci, i + 1);
- if (request_irq(pci->irq, snd_vx_irq_handler, IRQF_DISABLED|IRQF_SHARED,
- CARD_NAME, (void *) chip)) {
+ if (request_irq(pci->irq, snd_vx_irq_handler, IRQF_SHARED,
+ CARD_NAME, chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_vx222_free(chip);
return -EBUSY;
static long joystick_port[SNDRV_CARDS];
#endif
static int rear_switch[SNDRV_CARDS];
-static int rear_swap[SNDRV_CARDS] = { [0 ... (SNDRV_CARDS-1)] = 1 };
module_param_array(index, int, NULL, 0444);
MODULE_PARM_DESC(index, "Index value for the Yamaha DS-1 PCI soundcard.");
#endif
module_param_array(rear_switch, bool, NULL, 0444);
MODULE_PARM_DESC(rear_switch, "Enable shared rear/line-in switch");
-module_param_array(rear_swap, bool, NULL, 0444);
-MODULE_PARM_DESC(rear_swap, "Swap rear channels (must be enabled for correct IEC958 (S/PDIF)) output");
static struct pci_device_id snd_ymfpci_ids[] = {
{ 0x1073, 0x0004, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0, }, /* YMF724 */
snd_card_free(card);
return err;
}
- if ((err = snd_ymfpci_mixer(chip, rear_switch[dev], rear_swap[dev])) < 0) {
+ if ((err = snd_ymfpci_mixer(chip, rear_switch[dev])) < 0) {
snd_card_free(card);
return err;
}
ypcm = runtime->private_data;
ypcm->output_front = 1;
ypcm->output_rear = chip->mode_dup4ch ? 1 : 0;
- ypcm->swap_rear = chip->rear_swap;
+ ypcm->swap_rear = 0;
spin_lock_irq(&chip->reg_lock);
if (ypcm->output_rear) {
ymfpci_open_extension(chip);
ypcm = runtime->private_data;
ypcm->output_front = 0;
ypcm->output_rear = 1;
+ ypcm->swap_rear = 1;
spin_lock_irq(&chip->reg_lock);
snd_ymfpci_writew(chip, YDSXGR_SPDIFOUTCTRL,
snd_ymfpci_readw(chip, YDSXGR_SPDIFOUTCTRL) | 2);
ypcm = runtime->private_data;
ypcm->output_front = 0;
ypcm->output_rear = 1;
+ ypcm->swap_rear = 0;
spin_lock_irq(&chip->reg_lock);
ymfpci_open_extension(chip);
chip->rear_opened++;
chip->ac97 = NULL;
}
-int __devinit snd_ymfpci_mixer(struct snd_ymfpci *chip, int rear_switch, int rear_swap)
+int __devinit snd_ymfpci_mixer(struct snd_ymfpci *chip, int rear_switch)
{
struct snd_ac97_template ac97;
struct snd_kcontrol *kctl;
.read = snd_ymfpci_codec_read,
};
- chip->rear_swap = rear_swap;
if ((err = snd_ac97_bus(chip->card, 0, &ops, chip, &chip->ac97_bus)) < 0)
return err;
chip->ac97_bus->private_free = snd_ymfpci_mixer_free_ac97_bus;
chip->bank_size_effect = snd_ymfpci_readl(chip, YDSXGR_EFFCTRLSIZE) << 2;
chip->work_size = YDSXG_DEFAULT_WORK_SIZE;
- size = ((playback_ctrl_size + 0x00ff) & ~0x00ff) +
- ((chip->bank_size_playback * 2 * YDSXG_PLAYBACK_VOICES + 0x00ff) & ~0x00ff) +
- ((chip->bank_size_capture * 2 * YDSXG_CAPTURE_VOICES + 0x00ff) & ~0x00ff) +
- ((chip->bank_size_effect * 2 * YDSXG_EFFECT_VOICES + 0x00ff) & ~0x00ff) +
+ size = ALIGN(playback_ctrl_size, 0x100) +
+ ALIGN(chip->bank_size_playback * 2 * YDSXG_PLAYBACK_VOICES, 0x100) +
+ ALIGN(chip->bank_size_capture * 2 * YDSXG_CAPTURE_VOICES, 0x100) +
+ ALIGN(chip->bank_size_effect * 2 * YDSXG_EFFECT_VOICES, 0x100) +
chip->work_size;
/* work_ptr must be aligned to 256 bytes, but it's already
covered with the kernel page allocation mechanism */
chip->bank_base_playback_addr = ptr_addr;
chip->ctrl_playback = (u32 *)ptr;
chip->ctrl_playback[0] = cpu_to_le32(YDSXG_PLAYBACK_VOICES);
- ptr += (playback_ctrl_size + 0x00ff) & ~0x00ff;
- ptr_addr += (playback_ctrl_size + 0x00ff) & ~0x00ff;
+ ptr += ALIGN(playback_ctrl_size, 0x100);
+ ptr_addr += ALIGN(playback_ctrl_size, 0x100);
for (voice = 0; voice < YDSXG_PLAYBACK_VOICES; voice++) {
chip->voices[voice].number = voice;
chip->voices[voice].bank = (struct snd_ymfpci_playback_bank *)ptr;
ptr_addr += chip->bank_size_playback;
}
}
- ptr = (char *)(((unsigned long)ptr + 0x00ff) & ~0x00ff);
- ptr_addr = (ptr_addr + 0x00ff) & ~0x00ff;
+ ptr = (char *)ALIGN((unsigned long)ptr, 0x100);
+ ptr_addr = ALIGN(ptr_addr, 0x100);
chip->bank_base_capture = ptr;
chip->bank_base_capture_addr = ptr_addr;
for (voice = 0; voice < YDSXG_CAPTURE_VOICES; voice++)
ptr += chip->bank_size_capture;
ptr_addr += chip->bank_size_capture;
}
- ptr = (char *)(((unsigned long)ptr + 0x00ff) & ~0x00ff);
- ptr_addr = (ptr_addr + 0x00ff) & ~0x00ff;
+ ptr = (char *)ALIGN((unsigned long)ptr, 0x100);
+ ptr_addr = ALIGN(ptr_addr, 0x100);
chip->bank_base_effect = ptr;
chip->bank_base_effect_addr = ptr_addr;
for (voice = 0; voice < YDSXG_EFFECT_VOICES; voice++)
ptr += chip->bank_size_effect;
ptr_addr += chip->bank_size_effect;
}
- ptr = (char *)(((unsigned long)ptr + 0x00ff) & ~0x00ff);
- ptr_addr = (ptr_addr + 0x00ff) & ~0x00ff;
+ ptr = (char *)ALIGN((unsigned long)ptr, 0x100);
+ ptr_addr = ALIGN(ptr_addr, 0x100);
chip->work_base = ptr;
chip->work_base_addr = ptr_addr;
snd_dma_free_pages(&chip->work_ptr);
if (chip->irq >= 0)
- free_irq(chip->irq, (void *)chip);
+ free_irq(chip->irq, chip);
release_and_free_resource(chip->res_reg_area);
pci_write_config_word(chip->pci, 0x40, chip->old_legacy_ctrl);
chip->pci = pci;
chip->irq = -1;
chip->device_id = pci->device;
- pci_read_config_byte(pci, PCI_REVISION_ID, (u8 *)&chip->rev);
+ pci_read_config_byte(pci, PCI_REVISION_ID, &chip->rev);
chip->reg_area_phys = pci_resource_start(pci, 0);
chip->reg_area_virt = ioremap_nocache(chip->reg_area_phys, 0x8000);
pci_set_master(pci);
snd_ymfpci_free(chip);
return -EBUSY;
}
- if (request_irq(pci->irq, snd_ymfpci_interrupt, IRQF_DISABLED|IRQF_SHARED, "YMFPCI", (void *) chip)) {
+ if (request_irq(pci->irq, snd_ymfpci_interrupt, IRQF_SHARED,
+ "YMFPCI", chip)) {
snd_printk(KERN_ERR "unable to grab IRQ %d\n", pci->irq);
snd_ymfpci_free(chip);
return -EBUSY;
return -EIO;
}
- chip->rear_swap = 1;
if ((err = snd_ymfpci_ac3_init(chip)) < 0) {
snd_ymfpci_free(chip);
return err;
printk(KERN_WARNING "invalid nrpacks value.\n");
return -EINVAL;
}
- usb_register(&usb_audio_driver);
- return 0;
+ return usb_register(&usb_audio_driver);
}
git.openpandora.org / pandora-kernel.git / commitdiff