Staging: comedi: Fixed long line lengths in comedi.h

This patches fixes long line lengths in comedi.h that were picked up by
checkpatch.pl

Signed-off-by: Mark Rankilor <reodge@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

diff --git a/drivers/staging/comedi/comedi.h b/drivers/staging/comedi/comedi.h
index 1538146..3e3663f 100644 (file)
--- a/drivers/staging/comedi/comedi.h
+++ b/drivers/staging/comedi/comedi.h
@@ -465,7 +465,8 @@
 
 #define COMEDI_CB_EOS          1       /* end of scan */
 #define COMEDI_CB_EOA          2       /* end of acquisition */
-#define COMEDI_CB_BLOCK                4       /* data has arrived: wakes up read() / write() */
+#define COMEDI_CB_BLOCK                4       /* data has arrived:
+                                        * wakes up read() / write() */
 #define COMEDI_CB_EOBUF                8       /* DEPRECATED: end of buffer */
 #define COMEDI_CB_ERROR                16      /* card error during acquisition */
 #define COMEDI_CB_OVERFLOW     32      /* buffer overflow/underflow */
@@ -499,8 +500,10 @@
                I8254_MODE2 = (2 << 1), /* Rate generator */
                I8254_MODE3 = (3 << 1), /* Square wave mode */
                I8254_MODE4 = (4 << 1), /* Software triggered strobe */
-               I8254_MODE5 = (5 << 1), /* Hardware triggered strobe (retriggerable) */
-               I8254_BCD = 1,  /* use binary-coded decimal instead of binary (pretty useless) */
+               I8254_MODE5 = (5 << 1), /* Hardware triggered strobe
+                                        * (retriggerable) */
+               I8254_BCD = 1,  /* use binary-coded decimal instead of binary
+                                * (pretty useless) */
                I8254_BINARY = 0
        };
 
@@ -640,7 +643,8 @@ May be bitwise-or'd with CR_EDGE or CR_INVERT. */
                NI_GPCT_UP_DOWN_PIN_i_GATE_SELECT = 0x201,
                NI_GPCT_SELECTED_GATE_GATE_SELECT = 0x21e,
                /* m-series "second gate" sources are unknown,
-                  we should add them here with an offset of 0x300 when known. */
+                * we should add them here with an offset of 0x300 when
+                * known. */
                NI_GPCT_DISABLED_GATE_SELECT = 0x8000,
        };
        static inline unsigned NI_GPCT_GATE_PIN_GATE_SELECT(unsigned n)
@@ -681,14 +685,14 @@ INSN_CONFIG_SET_OTHER_SRC when using NI general-purpose counters. */
 INSN_CONFIG_ARM */
        enum ni_gpct_arm_source {
                NI_GPCT_ARM_IMMEDIATE = 0x0,
-               NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1,     /* Start both the counter and
-                                                          the adjacent paired counter
-                                                          simultaneously */
-               /* NI doesn't document bits for selecting hardware arm triggers.  If
-                * the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least
-                * significant bits (3 bits for 660x or 5 bits for m-series) through to
-                * the hardware.  This will at least allow someone to figure out what
-                * the bits do later. */
+               NI_GPCT_ARM_PAIRED_IMMEDIATE = 0x1, /* Start both the counter
+                                                    * and the adjacent paired
+                                                    * counter simultaneously */
+               /* NI doesn't document bits for selecting hardware arm triggers.
+                * If the NI_GPCT_ARM_UNKNOWN bit is set, we will pass the least
+                * significant bits (3 bits for 660x or 5 bits for m-series)
+                * through to the hardware.  This will at least allow someone to
+                * figure out what the bits do later. */
                NI_GPCT_ARM_UNKNOWN = 0x1000,
        };
 
@@ -740,8 +744,8 @@ INSN_CONFIG_ARM */
                NI_RTSI_OUTPUT_G_GATE0 = 6,
                NI_RTSI_OUTPUT_RGOUT0 = 7,
                NI_RTSI_OUTPUT_RTSI_BRD_0 = 8,
-               NI_RTSI_OUTPUT_RTSI_OSC = 12    /* pre-m-series always have RTSI clock
-                                                  on line 7 */
+               NI_RTSI_OUTPUT_RTSI_OSC = 12    /* pre-m-series always have RTSI
+                                                * clock on line 7 */
        };
        static inline unsigned NI_RTSI_OUTPUT_RTSI_BRD(unsigned n)
        {