Required properties:
- compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
Should be "ti,omap4-l3-noc" for OMAP4 family
+ Should be "ti,omap5-l3-noc" for OMAP5 family
Should be "ti,dra7-l3-noc" for DRA7 family
Should be "ti,am4372-l3-noc" for AM43 family
- reg: Contains L3 register address range for each noc domain.
pinctrl-0 = <&matrix_keypad_pins>;
debounce-delay-ms = <5>;
- col-scan-delay-us = <1500>;
+ col-scan-delay-us = <5>;
row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH /* Bank5, pin5 */
&gpio5 6 GPIO_ACTIVE_HIGH>; /* Bank5, pin6 */
interrupt-parent = <&gpio0>;
interrupts = <31 0>;
- wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
touchscreen-size-x = <480>;
touchscreen-size-y = <272>;
aliases {
rtc0 = &mcp_rtc;
rtc1 = &tps659038_rtc;
+ rtc2 = &rtc;
};
memory {
gpio_fan: gpio_fan {
/* Based on 5v 500mA AFB02505HHB */
compatible = "gpio-fan";
- gpios = <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
+ gpios = <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
gpio-fan,speed-map = <0 0>,
<13000 1>;
#cooling-cells = <2>;
uart3_pins_default: uart3_pins_default {
pinctrl-single,pins = <
- 0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
- 0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
+ 0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
+ 0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
>;
};
mcp_rtc: rtc@6f {
compatible = "microchip,mcp7941x";
reg = <0x6f>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>; /* IRQ_SYS_1N */
+ interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>; /* IRQ_SYS_1N */
pinctrl-names = "default";
pinctrl-0 = <&mcp79410_pins_default>;
&uart3 {
status = "okay";
interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
- <&dra7_pmx_core 0x248>;
+ <&dra7_pmx_core 0x3f8>;
pinctrl-names = "default";
pinctrl-0 = <&uart3_pins_default>;
ti,clock-cycles = <16>;
reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
- <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+ <0x4ae06014 0x4>, <0x4a003b20 0xc>,
<0x4ae0c158 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
ti,clock-cycles = <16>;
reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
- <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+ <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
<0x4a002470 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
ti,clock-cycles = <16>;
reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
- <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+ <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
<0x4a00246c 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
ti,clock-cycles = <16>;
reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
- <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+ <0x4ae06010 0x4>, <0x4a003b08 0xc>,
<0x4ae0c154 0x4>;
reg-names = "setup-address", "control-address",
"int-address", "efuse-address",
status = "disabled";
};
- rtc@48838000 {
+ rtc: rtc@48838000 {
compatible = "ti,am3352-rtc";
reg = <0x48838000 0x100>;
interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,
DRVDD-supply = <&vmmc2>;
IOVDD-supply = <&vio>;
DVDD-supply = <&vio>;
+
+ ai3x-micbias-vg = <1>;
};
tlv320aic3x_aux: tlv320aic3x@19 {
DRVDD-supply = <&vmmc2>;
IOVDD-supply = <&vio>;
DVDD-supply = <&vio>;
+
+ ai3x-micbias-vg = <2>;
};
tsl2563: tsl2563@29 {
};
mmu_isp: mmu@480bd400 {
+ #iommu-cells = <0>;
compatible = "ti,omap2-iommu";
reg = <0x480bd400 0x80>;
interrupts = <24>;
};
mmu_iva: mmu@5d000000 {
+ #iommu-cells = <0>;
compatible = "ti,omap2-iommu";
reg = <0x5d000000 0x80>;
interrupts = <28>;
* hierarchy.
*/
ocp {
- compatible = "ti,omap4-l3-noc", "simple-bus";
+ compatible = "ti,omap5-l3-noc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
CONFIG_DMA_OMAP=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_EXTCON=m
-CONFIG_EXTCON_GPIO=m
+CONFIG_EXTCON_USB_GPIO=m
CONFIG_EXTCON_PALMAS=m
CONFIG_TI_EMIF=m
CONFIG_PWM=y
#define OMAP3430_VC_CMD_ONLP_SHIFT 16
#define OMAP3430_VC_CMD_RET_SHIFT 8
#define OMAP3430_VC_CMD_OFF_SHIFT 0
+#define OMAP3430_SREN_MASK (1 << 4)
#define OMAP3430_HSEN_MASK (1 << 3)
#define OMAP3430_MCODE_MASK (0x7 << 0)
#define OMAP3430_VALID_MASK (1 << 24)
#define OMAP4430_GLOBAL_WARM_SW_RST_SHIFT 1
#define OMAP4430_GLOBAL_WUEN_MASK (1 << 16)
#define OMAP4430_HSMCODE_MASK (0x7 << 0)
+#define OMAP4430_SRMODEEN_MASK (1 << 4)
#define OMAP4430_HSMODEEN_MASK (1 << 3)
#define OMAP4430_HSSCLL_SHIFT 24
#define OMAP4430_ICEPICK_RST_SHIFT 9
* idle. And we can also scale voltages to zero for off-idle.
* Note that no actual voltage scaling during off-idle will
* happen unless the board specific twl4030 PMIC scripts are
- * loaded.
+ * loaded. See also omap_vc_i2c_init for comments regarding
+ * erratum i531.
*/
val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
return;
}
+ /*
+ * Note that for omap3 OMAP3430_SREN_MASK clears SREN to work around
+ * erratum i531 "Extra Power Consumed When Repeated Start Operation
+ * Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)".
+ * Otherwise I2C4 eventually leads into about 23mW extra power being
+ * consumed even during off idle using VMODE.
+ */
i2c_high_speed = voltdm->pmic->i2c_high_speed;
if (i2c_high_speed)
- voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
+ voltdm->rmw(vc->common->i2c_cfg_clear_mask,
vc->common->i2c_cfg_hsen_mask,
vc->common->i2c_cfg_reg);
* @cmd_ret_shift: RET field shift in PRM_VC_CMD_VAL_* register
* @cmd_off_shift: OFF field shift in PRM_VC_CMD_VAL_* register
* @i2c_cfg_reg: I2C configuration register offset
+ * @i2c_cfg_clear_mask: high-speed mode bit clear mask in I2C config register
* @i2c_cfg_hsen_mask: high-speed mode bit field mask in I2C config register
* @i2c_mcode_mask: MCODE field mask for I2C config register
*
u8 cmd_ret_shift;
u8 cmd_off_shift;
u8 i2c_cfg_reg;
+ u8 i2c_cfg_clear_mask;
u8 i2c_cfg_hsen_mask;
u8 i2c_mcode_mask;
};
.cmd_onlp_shift = OMAP3430_VC_CMD_ONLP_SHIFT,
.cmd_ret_shift = OMAP3430_VC_CMD_RET_SHIFT,
.cmd_off_shift = OMAP3430_VC_CMD_OFF_SHIFT,
+ .i2c_cfg_clear_mask = OMAP3430_SREN_MASK | OMAP3430_HSEN_MASK,
.i2c_cfg_hsen_mask = OMAP3430_HSEN_MASK,
.i2c_cfg_reg = OMAP3_PRM_VC_I2C_CFG_OFFSET,
.i2c_mcode_mask = OMAP3430_MCODE_MASK,
.cmd_ret_shift = OMAP4430_RET_SHIFT,
.cmd_off_shift = OMAP4430_OFF_SHIFT,
.i2c_cfg_reg = OMAP4_PRM_VC_CFG_I2C_MODE_OFFSET,
+ .i2c_cfg_clear_mask = OMAP4430_SRMODEEN_MASK | OMAP4430_HSMODEEN_MASK,
.i2c_cfg_hsen_mask = OMAP4430_HSMODEEN_MASK,
.i2c_mcode_mask = OMAP4430_HSMCODE_MASK,
};
/*
* OMAP L3 Interconnect error handling driver
*
- * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/
* Santosh Shilimkar <santosh.shilimkar@ti.com>
* Sricharan <r.sricharan@ti.com>
*
}
static const struct of_device_id l3_noc_match[] = {
- {.compatible = "ti,omap4-l3-noc", .data = &omap_l3_data},
+ {.compatible = "ti,omap4-l3-noc", .data = &omap4_l3_data},
+ {.compatible = "ti,omap5-l3-noc", .data = &omap5_l3_data},
{.compatible = "ti,dra7-l3-noc", .data = &dra_l3_data},
{.compatible = "ti,am4372-l3-noc", .data = &am4372_l3_data},
{},
/*
* OMAP L3 Interconnect error handling driver header
*
- * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/
* Santosh Shilimkar <santosh.shilimkar@ti.com>
* sricharan <r.sricharan@ti.com>
*
};
-static struct l3_target_data omap_l3_target_data_clk3[] = {
- {0x0100, "EMUSS",},
- {0x0300, "DEBUG SOURCE",},
- {0x0, "HOST CLK3",},
+static struct l3_target_data omap4_l3_target_data_clk3[] = {
+ {0x0100, "DEBUGSS",},
};
-static struct l3_flagmux_data omap_l3_flagmux_clk3 = {
+static struct l3_flagmux_data omap4_l3_flagmux_clk3 = {
.offset = 0x0200,
- .l3_targ = omap_l3_target_data_clk3,
- .num_targ_data = ARRAY_SIZE(omap_l3_target_data_clk3),
+ .l3_targ = omap4_l3_target_data_clk3,
+ .num_targ_data = ARRAY_SIZE(omap4_l3_target_data_clk3),
};
static struct l3_masters_data omap_l3_masters[] = {
{ 0x32, "USBHOSTFS"}
};
-static struct l3_flagmux_data *omap_l3_flagmux[] = {
+static struct l3_flagmux_data *omap4_l3_flagmux[] = {
&omap_l3_flagmux_clk1,
&omap_l3_flagmux_clk2,
- &omap_l3_flagmux_clk3,
+ &omap4_l3_flagmux_clk3,
};
-static const struct omap_l3 omap_l3_data = {
- .l3_flagmux = omap_l3_flagmux,
- .num_modules = ARRAY_SIZE(omap_l3_flagmux),
+static const struct omap_l3 omap4_l3_data = {
+ .l3_flagmux = omap4_l3_flagmux,
+ .num_modules = ARRAY_SIZE(omap4_l3_flagmux),
.l3_masters = omap_l3_masters,
.num_masters = ARRAY_SIZE(omap_l3_masters),
/* The 6 MSBs of register field used to distinguish initiator */
.mst_addr_mask = 0xFC,
};
+/* OMAP5 data */
+static struct l3_target_data omap5_l3_target_data_clk3[] = {
+ {0x0100, "L3INSTR",},
+ {0x0300, "DEBUGSS",},
+ {0x0, "HOSTCLK3",},
+};
+
+static struct l3_flagmux_data omap5_l3_flagmux_clk3 = {
+ .offset = 0x0200,
+ .l3_targ = omap5_l3_target_data_clk3,
+ .num_targ_data = ARRAY_SIZE(omap5_l3_target_data_clk3),
+};
+
+static struct l3_flagmux_data *omap5_l3_flagmux[] = {
+ &omap_l3_flagmux_clk1,
+ &omap_l3_flagmux_clk2,
+ &omap5_l3_flagmux_clk3,
+};
+
+static const struct omap_l3 omap5_l3_data = {
+ .l3_flagmux = omap5_l3_flagmux,
+ .num_modules = ARRAY_SIZE(omap5_l3_flagmux),
+ .l3_masters = omap_l3_masters,
+ .num_masters = ARRAY_SIZE(omap_l3_masters),
+ /* The 6 MSBs of register field used to distinguish initiator */
+ .mst_addr_mask = 0x7E0,
+};
+
/* DRA7 data */
static struct l3_target_data dra_l3_target_data_clk1[] = {
{0x2a00, "AES1",},
static struct l3_target_data dra_l3_target_data_clk2[] = {
{0x0, "HOST CLK1",},
- {0x0, "HOST CLK2",},
+ {0x800000, "HOST CLK2",},
{0xdead, L3_TARGET_NOT_SUPPORTED,},
{0x3400, "SHA2_2",},
{0x0900, "BB2D",},