#include "net2280.h"
-#define valid_bit cpu_to_le32 (1 << VALID_BIT)
-#define dma_done_ie cpu_to_le32 (1 << DMA_DONE_INTERRUPT_ENABLE)
+#define valid_bit cpu_to_le32(BIT(VALID_BIT))
+#define dma_done_ie cpu_to_le32(BIT(DMA_DONE_INTERRUPT_ENABLE))
/*-------------------------------------------------------------------------*/
static inline void enable_pciirqenb(struct net2280_ep *ep)
u32 tmp = readl(&ep->dev->regs->pciirqenb0);
if (ep->dev->pdev->vendor == PCI_VENDOR_ID_PLX_LEGACY)
- tmp |= 1 << ep->num;
+ tmp |= BIT(ep->num);
else
- tmp |= 1 << ep_bit[ep->num];
+ tmp |= BIT(ep_bit[ep->num]);
writel(tmp, &ep->dev->regs->pciirqenb0);
return;
}
/* set type, direction, address; reset fifo counters */
- writel ((1 << FIFO_FLUSH), &ep->regs->ep_stat);
+ writel(BIT(FIFO_FLUSH), &ep->regs->ep_stat);
tmp = (desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK);
if (tmp == USB_ENDPOINT_XFER_INT) {
/* erratum 0105 workaround prevents hs NYET */
if (dev->chiprev == 0100
&& dev->gadget.speed == USB_SPEED_HIGH
&& !(desc->bEndpointAddress & USB_DIR_IN))
- writel ((1 << CLEAR_NAK_OUT_PACKETS_MODE),
+ writel(BIT(CLEAR_NAK_OUT_PACKETS_MODE),
&ep->regs->ep_rsp);
} else if (tmp == USB_ENDPOINT_XFER_BULK) {
/* catch some particularly blatant driver bugs */
tmp |= desc->bEndpointAddress;
/* default full fifo lines */
tmp |= (4 << ENDPOINT_BYTE_COUNT);
- tmp |= 1 << ENDPOINT_ENABLE;
+ tmp |= BIT(ENDPOINT_ENABLE);
ep->is_in = (tmp & USB_DIR_IN) != 0;
} else {
/* In Legacy mode, only OUT endpoints are used */
if (dev->enhanced_mode && ep->is_in) {
tmp <<= IN_ENDPOINT_TYPE;
- tmp |= (1 << IN_ENDPOINT_ENABLE);
+ tmp |= BIT(IN_ENDPOINT_ENABLE);
/* Not applicable to Legacy */
- tmp |= (1 << ENDPOINT_DIRECTION);
+ tmp |= BIT(ENDPOINT_DIRECTION);
} else {
tmp <<= OUT_ENDPOINT_TYPE;
- tmp |= (1 << OUT_ENDPOINT_ENABLE);
+ tmp |= BIT(OUT_ENDPOINT_ENABLE);
tmp |= (ep->is_in << ENDPOINT_DIRECTION);
}
/* for OUT transfers, block the rx fifo until a read is posted */
if (!ep->is_in)
- writel ((1 << SET_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
+ writel(BIT(SET_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
else if (dev->pdev->device != 0x2280) {
/* Added for 2282, Don't use nak packets on an in endpoint,
* this was ignored on 2280
*/
- writel ((1 << CLEAR_NAK_OUT_PACKETS)
- | (1 << CLEAR_NAK_OUT_PACKETS_MODE), &ep->regs->ep_rsp);
+ writel(BIT(CLEAR_NAK_OUT_PACKETS) |
+ BIT(CLEAR_NAK_OUT_PACKETS_MODE), &ep->regs->ep_rsp);
}
writel(tmp, &ep->cfg->ep_cfg);
if (!ep->dma) { /* pio, per-packet */
enable_pciirqenb(ep);
- tmp = (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
- | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE);
+ tmp = BIT(DATA_PACKET_RECEIVED_INTERRUPT_ENABLE) |
+ BIT(DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE);
if (dev->pdev->device == 0x2280)
tmp |= readl (&ep->regs->ep_irqenb);
writel (tmp, &ep->regs->ep_irqenb);
} else { /* dma, per-request */
- tmp = (1 << (8 + ep->num)); /* completion */
+ tmp = BIT((8 + ep->num)); /* completion */
tmp |= readl (&dev->regs->pciirqenb1);
writel (tmp, &dev->regs->pciirqenb1);
* NOTE erratum 0112 workaround #2
*/
if ((desc->bEndpointAddress & USB_DIR_IN) == 0) {
- tmp = (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE);
+ tmp = BIT(SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE);
writel (tmp, &ep->regs->ep_irqenb);
enable_pciirqenb(ep);
/* disable the dma, irqs, endpoint... */
if (ep->dma) {
writel (0, &ep->dma->dmactl);
- writel ( (1 << DMA_SCATTER_GATHER_DONE_INTERRUPT)
- | (1 << DMA_TRANSACTION_DONE_INTERRUPT)
- | (1 << DMA_ABORT)
- , &ep->dma->dmastat);
+ writel(BIT(DMA_SCATTER_GATHER_DONE_INTERRUPT) |
+ BIT(DMA_TRANSACTION_DONE_INTERRUPT) |
+ BIT(DMA_ABORT),
+ &ep->dma->dmastat);
tmp = readl (®s->pciirqenb0);
- tmp &= ~(1 << ep->num);
+ tmp &= ~BIT(ep->num);
writel (tmp, ®s->pciirqenb0);
} else {
tmp = readl (®s->pciirqenb1);
- tmp &= ~(1 << (8 + ep->num)); /* completion */
+ tmp &= ~BIT((8 + ep->num)); /* completion */
writel (tmp, ®s->pciirqenb1);
}
writel (0, &ep->regs->ep_irqenb);
* packets until the driver queues a read (+note erratum 0112)
*/
if (!ep->is_in || ep->dev->pdev->device == 0x2280) {
- tmp = (1 << SET_NAK_OUT_PACKETS_MODE)
- | (1 << SET_NAK_OUT_PACKETS)
- | (1 << CLEAR_EP_HIDE_STATUS_PHASE)
- | (1 << CLEAR_INTERRUPT_MODE);
+ tmp = BIT(SET_NAK_OUT_PACKETS_MODE) |
+ BIT(SET_NAK_OUT_PACKETS) |
+ BIT(CLEAR_EP_HIDE_STATUS_PHASE) |
+ BIT(CLEAR_INTERRUPT_MODE);
} else {
/* added for 2282 */
- tmp = (1 << CLEAR_NAK_OUT_PACKETS_MODE)
- | (1 << CLEAR_NAK_OUT_PACKETS)
- | (1 << CLEAR_EP_HIDE_STATUS_PHASE)
- | (1 << CLEAR_INTERRUPT_MODE);
+ tmp = BIT(CLEAR_NAK_OUT_PACKETS_MODE) |
+ BIT(CLEAR_NAK_OUT_PACKETS) |
+ BIT(CLEAR_EP_HIDE_STATUS_PHASE) |
+ BIT(CLEAR_INTERRUPT_MODE);
}
if (ep->num != 0) {
- tmp |= (1 << CLEAR_ENDPOINT_TOGGLE)
- | (1 << CLEAR_ENDPOINT_HALT);
+ tmp |= BIT(CLEAR_ENDPOINT_TOGGLE) |
+ BIT(CLEAR_ENDPOINT_HALT);
}
writel (tmp, &ep->regs->ep_rsp);
/* scrub most status bits, and flush any fifo state */
if (ep->dev->pdev->device == 0x2280)
- tmp = (1 << FIFO_OVERFLOW)
- | (1 << FIFO_UNDERFLOW);
+ tmp = BIT(FIFO_OVERFLOW) |
+ BIT(FIFO_UNDERFLOW);
else
tmp = 0;
- writel (tmp | (1 << TIMEOUT)
- | (1 << USB_STALL_SENT)
- | (1 << USB_IN_NAK_SENT)
- | (1 << USB_IN_ACK_RCVD)
- | (1 << USB_OUT_PING_NAK_SENT)
- | (1 << USB_OUT_ACK_SENT)
- | (1 << FIFO_FLUSH)
- | (1 << SHORT_PACKET_OUT_DONE_INTERRUPT)
- | (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT)
- | (1 << DATA_PACKET_RECEIVED_INTERRUPT)
- | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)
- | (1 << DATA_OUT_PING_TOKEN_INTERRUPT)
- | (1 << DATA_IN_TOKEN_INTERRUPT)
+ writel(tmp | BIT(TIMEOUT) |
+ BIT(USB_STALL_SENT) |
+ BIT(USB_IN_NAK_SENT) |
+ BIT(USB_IN_ACK_RCVD) |
+ BIT(USB_OUT_PING_NAK_SENT) |
+ BIT(USB_OUT_ACK_SENT) |
+ BIT(FIFO_FLUSH) |
+ BIT(SHORT_PACKET_OUT_DONE_INTERRUPT) |
+ BIT(SHORT_PACKET_TRANSFERRED_INTERRUPT) |
+ BIT(DATA_PACKET_RECEIVED_INTERRUPT) |
+ BIT(DATA_PACKET_TRANSMITTED_INTERRUPT) |
+ BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
+ BIT(DATA_IN_TOKEN_INTERRUPT)
, &ep->regs->ep_stat);
/* fifo size is handled separately */
/* disable the dma, irqs, endpoint... */
if (ep->dma) {
writel(0, &ep->dma->dmactl);
- writel((1 << DMA_ABORT_DONE_INTERRUPT) |
- (1 << DMA_PAUSE_DONE_INTERRUPT) |
- (1 << DMA_SCATTER_GATHER_DONE_INTERRUPT) |
- (1 << DMA_TRANSACTION_DONE_INTERRUPT)
- /* | (1 << DMA_ABORT) */
+ writel(BIT(DMA_ABORT_DONE_INTERRUPT) |
+ BIT(DMA_PAUSE_DONE_INTERRUPT) |
+ BIT(DMA_SCATTER_GATHER_DONE_INTERRUPT) |
+ BIT(DMA_TRANSACTION_DONE_INTERRUPT)
+ /* | BIT(DMA_ABORT) */
, &ep->dma->dmastat);
dmastat = readl(&ep->dma->dmastat);
}
tmp = readl(®s->pciirqenb0);
- tmp &= ~(1 << ep_bit[ep->num]);
+ tmp &= ~BIT(ep_bit[ep->num]);
writel(tmp, ®s->pciirqenb0);
} else {
if (ep->num < 5) {
tmp = readl(®s->pciirqenb1);
- tmp &= ~(1 << (8 + ep->num)); /* completion */
+ tmp &= ~BIT((8 + ep->num)); /* completion */
writel(tmp, ®s->pciirqenb1);
}
}
writel(0, &ep->regs->ep_irqenb);
- writel((1 << SHORT_PACKET_OUT_DONE_INTERRUPT) |
- (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT) |
- (1 << FIFO_OVERFLOW) |
- (1 << DATA_PACKET_RECEIVED_INTERRUPT) |
- (1 << DATA_PACKET_TRANSMITTED_INTERRUPT) |
- (1 << DATA_OUT_PING_TOKEN_INTERRUPT) |
- (1 << DATA_IN_TOKEN_INTERRUPT), &ep->regs->ep_stat);
+ writel(BIT(SHORT_PACKET_OUT_DONE_INTERRUPT) |
+ BIT(SHORT_PACKET_TRANSFERRED_INTERRUPT) |
+ BIT(FIFO_OVERFLOW) |
+ BIT(DATA_PACKET_RECEIVED_INTERRUPT) |
+ BIT(DATA_PACKET_TRANSMITTED_INTERRUPT) |
+ BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
+ BIT(DATA_IN_TOKEN_INTERRUPT), &ep->regs->ep_stat);
}
static void nuke (struct net2280_ep *);
ASSERT_OUT_NAKING (ep);
statp = &ep->regs->ep_stat;
- writel ( (1 << DATA_OUT_PING_TOKEN_INTERRUPT)
- | (1 << DATA_PACKET_RECEIVED_INTERRUPT)
+ writel(BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
+ BIT(DATA_PACKET_RECEIVED_INTERRUPT)
, statp);
- writel ((1 << FIFO_FLUSH), statp);
+ writel(BIT(FIFO_FLUSH), statp);
mb ();
tmp = readl (statp);
- if (tmp & (1 << DATA_OUT_PING_TOKEN_INTERRUPT)
+ if (tmp & BIT(DATA_OUT_PING_TOKEN_INTERRUPT)
/* high speed did bulk NYET; fifo isn't filling */
&& ep->dev->gadget.speed == USB_SPEED_FULL) {
unsigned usec;
usec = 50; /* 64 byte bulk/interrupt */
- handshake (statp, (1 << USB_OUT_PING_NAK_SENT),
- (1 << USB_OUT_PING_NAK_SENT), usec);
+ handshake(statp, BIT(USB_OUT_PING_NAK_SENT),
+ BIT(USB_OUT_PING_NAK_SENT), usec);
/* NAK done; now CLEAR_NAK_OUT_PACKETS is safe */
}
}
&& ep->dev->gadget.speed == USB_SPEED_FULL) {
udelay (1);
tmp = readl (&ep->regs->ep_stat);
- if ((tmp & (1 << NAK_OUT_PACKETS)))
+ if ((tmp & BIT(NAK_OUT_PACKETS)))
cleanup = 1;
- else if ((tmp & (1 << FIFO_FULL))) {
+ else if ((tmp & BIT(FIFO_FULL))) {
start_out_naking (ep);
prevent = 1;
}
tmp = readl (&ep->regs->ep_stat);
count = readl (®s->ep_avail);
/* handled that data already? */
- if (count == 0 && (tmp & (1 << NAK_OUT_PACKETS)) == 0)
+ if (count == 0 && (tmp & BIT(NAK_OUT_PACKETS)) == 0)
return 0;
}
if (cleanup)
out_flush (ep);
if (prevent) {
- writel ((1 << CLEAR_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
+ writel(BIT(CLEAR_NAK_OUT_PACKETS), &ep->regs->ep_rsp);
(void) readl (&ep->regs->ep_rsp);
}
* stop the fifo from filling but we can flush it.
*/
if (ep->is_in)
- dmacount |= (1 << DMA_DIRECTION);
+ dmacount |= BIT(DMA_DIRECTION);
if ((!ep->is_in && (dmacount % ep->ep.maxpacket) != 0)
|| ep->dev->pdev->device != 0x2280)
- dmacount |= (1 << END_OF_CHAIN);
+ dmacount |= BIT(END_OF_CHAIN);
req->valid = valid;
if (valid)
- dmacount |= (1 << VALID_BIT);
+ dmacount |= BIT(VALID_BIT);
if (likely(!req->req.no_interrupt || !use_dma_chaining))
- dmacount |= (1 << DMA_DONE_INTERRUPT_ENABLE);
+ dmacount |= BIT(DMA_DONE_INTERRUPT_ENABLE);
/* td->dmadesc = previously set by caller */
td->dmaaddr = cpu_to_le32 (req->req.dma);
}
static const u32 dmactl_default =
- (1 << DMA_SCATTER_GATHER_DONE_INTERRUPT)
- | (1 << DMA_CLEAR_COUNT_ENABLE)
+ BIT(DMA_SCATTER_GATHER_DONE_INTERRUPT) |
+ BIT(DMA_CLEAR_COUNT_ENABLE) |
/* erratum 0116 workaround part 1 (use POLLING) */
- | (POLL_100_USEC << DESCRIPTOR_POLLING_RATE)
- | (1 << DMA_VALID_BIT_POLLING_ENABLE)
- | (1 << DMA_VALID_BIT_ENABLE)
- | (1 << DMA_SCATTER_GATHER_ENABLE)
+ (POLL_100_USEC << DESCRIPTOR_POLLING_RATE) |
+ BIT(DMA_VALID_BIT_POLLING_ENABLE) |
+ BIT(DMA_VALID_BIT_ENABLE) |
+ BIT(DMA_SCATTER_GATHER_ENABLE) |
/* erratum 0116 workaround part 2 (no AUTOSTART) */
- | (1 << DMA_ENABLE);
+ BIT(DMA_ENABLE);
static inline void spin_stop_dma (struct net2280_dma_regs __iomem *dma)
{
- handshake (&dma->dmactl, (1 << DMA_ENABLE), 0, 50);
+ handshake(&dma->dmactl, BIT(DMA_ENABLE), 0, 50);
}
static inline void stop_dma (struct net2280_dma_regs __iomem *dma)
{
- writel (readl (&dma->dmactl) & ~(1 << DMA_ENABLE), &dma->dmactl);
+ writel(readl(&dma->dmactl) & ~BIT(DMA_ENABLE), &dma->dmactl);
spin_stop_dma (dma);
}
static void start_queue (struct net2280_ep *ep, u32 dmactl, u32 td_dma)
{
struct net2280_dma_regs __iomem *dma = ep->dma;
- unsigned int tmp = (1 << VALID_BIT) | (ep->is_in << DMA_DIRECTION);
+ unsigned int tmp = BIT(VALID_BIT) | (ep->is_in << DMA_DIRECTION);
if (ep->dev->pdev->device != 0x2280)
- tmp |= (1 << END_OF_CHAIN);
+ tmp |= BIT(END_OF_CHAIN);
writel (tmp, &dma->dmacount);
writel (readl (&dma->dmastat), &dma->dmastat);
writel (td_dma, &dma->dmadesc);
if (ep->dev->pdev->vendor == PCI_VENDOR_ID_PLX)
- dmactl |= (0x01 << DMA_REQUEST_OUTSTANDING);
+ dmactl |= BIT(DMA_REQUEST_OUTSTANDING);
writel (dmactl, &dma->dmactl);
/* erratum 0116 workaround part 3: pci arbiter away from net2280 */
(void) readl (&ep->dev->pci->pcimstctl);
- writel ((1 << DMA_START), &dma->dmastat);
+ writel(BIT(DMA_START), &dma->dmastat);
if (!ep->is_in)
stop_out_naking (ep);
/* FIXME can't use DMA for ZLPs */
/* on this path we "know" there's no dma active (yet) */
- WARN_ON (readl (&dma->dmactl) & (1 << DMA_ENABLE));
+ WARN_ON(readl(&dma->dmactl) & BIT(DMA_ENABLE));
writel (0, &ep->dma->dmactl);
/* previous OUT packet might have been short */
if (!ep->is_in && ((tmp = readl (&ep->regs->ep_stat))
- & (1 << NAK_OUT_PACKETS)) != 0) {
- writel ((1 << SHORT_PACKET_TRANSFERRED_INTERRUPT),
+ & BIT(NAK_OUT_PACKETS)) != 0) {
+ writel(BIT(SHORT_PACKET_TRANSFERRED_INTERRUPT),
&ep->regs->ep_stat);
tmp = readl (&ep->regs->ep_avail);
/* dma irq, faking scatterlist status */
req->td->dmacount = cpu_to_le32 (req->req.length - tmp);
- writel ((1 << DMA_DONE_INTERRUPT_ENABLE)
+ writel(BIT(DMA_DONE_INTERRUPT_ENABLE)
| tmp, &dma->dmacount);
req->td->dmadesc = 0;
req->valid = 1;
- writel ((1 << DMA_ENABLE), &dma->dmactl);
- writel ((1 << DMA_START), &dma->dmastat);
+ writel(BIT(DMA_ENABLE), &dma->dmactl);
+ writel(BIT(DMA_START), &dma->dmastat);
return;
}
}
if (ep->is_in) {
if (likely ((req->req.length % ep->ep.maxpacket) != 0
|| req->req.zero)) {
- tmp |= (1 << DMA_FIFO_VALIDATE);
+ tmp |= BIT(DMA_FIFO_VALIDATE);
ep->in_fifo_validate = 1;
} else
ep->in_fifo_validate = 0;
fill_dma_desc (ep, req, 1);
if (!use_dma_chaining)
- req->td->dmacount |= cpu_to_le32 (1 << END_OF_CHAIN);
+ req->td->dmacount |= cpu_to_le32(BIT(END_OF_CHAIN));
start_queue (ep, tmp, req->td_dma);
}
static inline void resume_dma(struct net2280_ep *ep)
{
- writel(readl(&ep->dma->dmactl) | (1 << DMA_ENABLE), &ep->dma->dmactl);
+ writel(readl(&ep->dma->dmactl) | BIT(DMA_ENABLE), &ep->dma->dmactl);
ep->dma_started = true;
}
static inline void ep_stop_dma(struct net2280_ep *ep)
{
- writel(readl(&ep->dma->dmactl) & ~(1 << DMA_ENABLE), &ep->dma->dmactl);
+ writel(readl(&ep->dma->dmactl) & ~BIT(DMA_ENABLE), &ep->dma->dmactl);
spin_stop_dma(ep->dma);
ep->dma_started = false;
if (list_empty (&ep->queue) && !ep->stopped) {
/* DMA request while EP halted */
if (ep->dma &&
- (readl(&ep->regs->ep_rsp) & (1 << CLEAR_ENDPOINT_HALT)) &&
+ (readl(&ep->regs->ep_rsp) & BIT(CLEAR_ENDPOINT_HALT)) &&
(dev->pdev->vendor == PCI_VENDOR_ID_PLX)) {
int valid = 1;
if (ep->is_in) {
/* OUT FIFO might have packet(s) buffered */
s = readl (&ep->regs->ep_stat);
- if ((s & (1 << FIFO_EMPTY)) == 0) {
+ if ((s & BIT(FIFO_EMPTY)) == 0) {
/* note: _req->short_not_ok is
* ignored here since PIO _always_
* stops queue advance here, and
}
/* don't NAK, let the fifo fill */
- if (req && (s & (1 << NAK_OUT_PACKETS)))
- writel ((1 << CLEAR_NAK_OUT_PACKETS),
+ if (req && (s & BIT(NAK_OUT_PACKETS)))
+ writel(BIT(CLEAR_NAK_OUT_PACKETS),
&ep->regs->ep_rsp);
}
}
break;
rmb ();
tmp = le32_to_cpup (&req->td->dmacount);
- if ((tmp & (1 << VALID_BIT)) != 0)
+ if ((tmp & BIT(VALID_BIT)) != 0)
break;
/* SHORT_PACKET_TRANSFERRED_INTERRUPT handles "usb-short"
* your gadget driver. That helps avoids errata 0121,
* 0122, and 0124; not all cases trigger the warning.
*/
- if ((tmp & (1 << NAK_OUT_PACKETS)) == 0) {
+ if ((tmp & BIT(NAK_OUT_PACKETS)) == 0) {
WARNING (ep->dev, "%s lost packet sync!\n",
ep->ep.name);
req->req.status = -EOVERFLOW;
ep->in_fifo_validate = likely (req->req.zero
|| (req->req.length % ep->ep.maxpacket) != 0);
if (ep->in_fifo_validate)
- dmactl |= (1 << DMA_FIFO_VALIDATE);
+ dmactl |= BIT(DMA_FIFO_VALIDATE);
list_for_each_entry (entry, &ep->queue, queue) {
__le32 dmacount;
/* abort the current transfer */
if (likely (!list_empty (&ep->queue))) {
/* FIXME work around errata 0121, 0122, 0124 */
- writel ((1 << DMA_ABORT), &ep->dma->dmastat);
+ writel(BIT(DMA_ABORT), &ep->dma->dmastat);
spin_stop_dma (ep->dma);
} else
stop_dma (ep->dma);
static void abort_dma_338x(struct net2280_ep *ep)
{
- writel((1 << DMA_ABORT), &ep->dma->dmastat);
+ writel(BIT(DMA_ABORT), &ep->dma->dmastat);
spin_stop_dma(ep->dma);
}
if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
return -ESHUTDOWN;
- avail = readl (&ep->regs->ep_avail) & ((1 << 12) - 1);
+ avail = readl(&ep->regs->ep_avail) & (BIT(12) - 1);
if (avail > ep->fifo_size)
return -EOVERFLOW;
if (ep->is_in)
if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
return;
- writel ((1 << FIFO_FLUSH), &ep->regs->ep_stat);
+ writel(BIT(FIFO_FLUSH), &ep->regs->ep_stat);
(void) readl (&ep->regs->ep_rsp);
}
spin_lock_irqsave (&dev->lock, flags);
tmp = readl (&dev->usb->usbctl);
- if (tmp & (1 << DEVICE_REMOTE_WAKEUP_ENABLE))
- writel (1 << GENERATE_RESUME, &dev->usb->usbstat);
+ if (tmp & BIT(DEVICE_REMOTE_WAKEUP_ENABLE))
+ writel(BIT(GENERATE_RESUME), &dev->usb->usbstat);
spin_unlock_irqrestore (&dev->lock, flags);
/* pci writes may still be posted */
spin_lock_irqsave (&dev->lock, flags);
tmp = readl (&dev->usb->usbctl);
if (value) {
- tmp |= (1 << SELF_POWERED_STATUS);
+ tmp |= BIT(SELF_POWERED_STATUS);
dev->selfpowered = 1;
} else {
- tmp &= ~(1 << SELF_POWERED_STATUS);
+ tmp &= ~BIT(SELF_POWERED_STATUS);
dev->selfpowered = 0;
}
writel (tmp, &dev->usb->usbctl);
tmp = readl (&dev->usb->usbctl);
dev->softconnect = (is_on != 0);
if (is_on)
- tmp |= (1 << USB_DETECT_ENABLE);
+ tmp |= BIT(USB_DETECT_ENABLE);
else
- tmp &= ~(1 << USB_DETECT_ENABLE);
+ tmp &= ~BIT(USB_DETECT_ENABLE);
writel (tmp, &dev->usb->usbctl);
spin_unlock_irqrestore (&dev->lock, flags);
/* USB Control Registers */
t1 = readl (&dev->usb->usbctl);
t2 = readl (&dev->usb->usbstat);
- if (t1 & (1 << VBUS_PIN)) {
- if (t2 & (1 << HIGH_SPEED))
+ if (t1 & BIT(VBUS_PIN)) {
+ if (t2 & BIT(HIGH_SPEED))
s = "high speed";
else if (dev->gadget.speed == USB_SPEED_UNKNOWN)
s = "powered";
"\n%s\tcfg %05x rsp (%02x) %s%s%s%s%s%s%s%s"
"irqenb %02x\n",
ep->ep.name, t1, t2,
- (t2 & (1 << CLEAR_NAK_OUT_PACKETS))
+ (t2 & BIT(CLEAR_NAK_OUT_PACKETS))
? "NAK " : "",
- (t2 & (1 << CLEAR_EP_HIDE_STATUS_PHASE))
+ (t2 & BIT(CLEAR_EP_HIDE_STATUS_PHASE))
? "hide " : "",
- (t2 & (1 << CLEAR_EP_FORCE_CRC_ERROR))
+ (t2 & BIT(CLEAR_EP_FORCE_CRC_ERROR))
? "CRC " : "",
- (t2 & (1 << CLEAR_INTERRUPT_MODE))
+ (t2 & BIT(CLEAR_INTERRUPT_MODE))
? "interrupt " : "",
- (t2 & (1<<CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE))
+ (t2 & BIT(CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE))
? "status " : "",
- (t2 & (1 << CLEAR_NAK_OUT_PACKETS_MODE))
+ (t2 & BIT(CLEAR_NAK_OUT_PACKETS_MODE))
? "NAKmode " : "",
- (t2 & (1 << CLEAR_ENDPOINT_TOGGLE))
+ (t2 & BIT(CLEAR_ENDPOINT_TOGGLE))
? "DATA1 " : "DATA0 ",
- (t2 & (1 << CLEAR_ENDPOINT_HALT))
+ (t2 & BIT(CLEAR_ENDPOINT_HALT))
? "HALT " : "",
readl (&ep->regs->ep_irqenb));
size -= t;
/* Change settings on some selected endpoints */
tmp_reg = readl(&dev->plregs->pl_ep_cfg_4);
- tmp_reg &= ~(1 << NON_CTRL_IN_TOLERATE_BAD_DIR);
+ tmp_reg &= ~BIT(NON_CTRL_IN_TOLERATE_BAD_DIR);
writel(tmp_reg, &dev->plregs->pl_ep_cfg_4);
tmp_reg = readl(&dev->plregs->pl_ep_ctrl);
- tmp_reg |= (1 << EP_INITIALIZED);
+ tmp_reg |= BIT(EP_INITIALIZED);
writel(tmp_reg, &dev->plregs->pl_ep_ctrl);
}
}
WARNING(dev, "It will operate on cold-reboot and SS connect");
/*GPEPs:*/
- tmp = ((0 << ENDPOINT_NUMBER) | (1 << ENDPOINT_DIRECTION) |
+ tmp = ((0 << ENDPOINT_NUMBER) | BIT(ENDPOINT_DIRECTION) |
(2 << OUT_ENDPOINT_TYPE) | (2 << IN_ENDPOINT_TYPE) |
((dev->enhanced_mode) ?
- 1 << OUT_ENDPOINT_ENABLE : 1 << ENDPOINT_ENABLE) |
- (1 << IN_ENDPOINT_ENABLE));
+ BIT(OUT_ENDPOINT_ENABLE) : BIT(ENDPOINT_ENABLE)) |
+ BIT(IN_ENDPOINT_ENABLE));
for (i = 1; i < 5; i++)
writel(tmp, &dev->ep[i].cfg->ep_cfg);
/* CSRIN, PCIIN, STATIN, RCIN*/
- tmp = ((0 << ENDPOINT_NUMBER) | (1 << ENDPOINT_ENABLE));
+ tmp = ((0 << ENDPOINT_NUMBER) | BIT(ENDPOINT_ENABLE));
writel(tmp, &dev->dep[1].dep_cfg);
writel(tmp, &dev->dep[3].dep_cfg);
writel(tmp, &dev->dep[4].dep_cfg);
if (ep_sel == 1) {
tmp =
(readl(&dev->plregs->pl_ep_ctrl) |
- (1 << CLEAR_ACK_ERROR_CODE) | 0);
+ BIT(CLEAR_ACK_ERROR_CODE) | 0);
writel(tmp, &dev->plregs->pl_ep_ctrl);
continue;
}
continue;
tmp = (readl(&dev->plregs->pl_ep_cfg_4) |
- (1 << NON_CTRL_IN_TOLERATE_BAD_DIR) | 0);
+ BIT(NON_CTRL_IN_TOLERATE_BAD_DIR) | 0);
writel(tmp, &dev->plregs->pl_ep_cfg_4);
tmp = readl(&dev->plregs->pl_ep_ctrl) &
- ~(1 << EP_INITIALIZED);
+ ~BIT(EP_INITIALIZED);
writel(tmp, &dev->plregs->pl_ep_ctrl);
}
}
writel (~0, &dev->regs->irqstat0),
- writel (~(1 << SUSPEND_REQUEST_INTERRUPT), &dev->regs->irqstat1),
+ writel(~(u32)BIT(SUSPEND_REQUEST_INTERRUPT), &dev->regs->irqstat1),
/* reset, and enable pci */
- tmp = readl (&dev->regs->devinit)
- | (1 << PCI_ENABLE)
- | (1 << FIFO_SOFT_RESET)
- | (1 << USB_SOFT_RESET)
- | (1 << M8051_RESET);
+ tmp = readl(&dev->regs->devinit) |
+ BIT(PCI_ENABLE) |
+ BIT(FIFO_SOFT_RESET) |
+ BIT(USB_SOFT_RESET) |
+ BIT(M8051_RESET);
writel (tmp, &dev->regs->devinit);
/* standard fifo and endpoint allocations */
if (fsmvalue == DEFECT7374_FSM_SS_CONTROL_READ) {
/* reset, and enable pci */
tmp = readl(&dev->regs->devinit) |
- (1 << PCI_ENABLE) |
- (1 << FIFO_SOFT_RESET) |
- (1 << USB_SOFT_RESET) |
- (1 << M8051_RESET);
+ BIT(PCI_ENABLE) |
+ BIT(FIFO_SOFT_RESET) |
+ BIT(USB_SOFT_RESET) |
+ BIT(M8051_RESET);
writel(tmp, &dev->regs->devinit);
}
__func__, fsmvalue);
else {
tmp = readl(&dev->usb_ext->usbctl2) &
- ~((1 << U1_ENABLE) | (1 << U2_ENABLE) | (1 << LTM_ENABLE));
+ ~(BIT(U1_ENABLE) | BIT(U2_ENABLE) | BIT(LTM_ENABLE));
writel(tmp, &dev->usb_ext->usbctl2);
}
* - Reference PLX TT-7372
*/
val = readl(&dev->ll_chicken_reg->ll_tsn_chicken_bit);
- val |= (1 << RECOVERY_IDLE_TO_RECOVER_FMW);
+ val |= BIT(RECOVERY_IDLE_TO_RECOVER_FMW);
writel(val, &dev->ll_chicken_reg->ll_tsn_chicken_bit);
INIT_LIST_HEAD(&dev->gadget.ep0->ep_list);
static void ep0_start_228x(struct net2280 *dev)
{
- writel ( (1 << CLEAR_EP_HIDE_STATUS_PHASE)
- | (1 << CLEAR_NAK_OUT_PACKETS)
- | (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
+ writel(BIT(CLEAR_EP_HIDE_STATUS_PHASE) |
+ BIT(CLEAR_NAK_OUT_PACKETS) |
+ BIT(CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE)
, &dev->epregs [0].ep_rsp);
/*
* endpoint status/features are handled in software, to
* help pass tests for some dubious behavior.
*/
- writel ( (1 << SET_TEST_MODE)
- | (1 << SET_ADDRESS)
- | (1 << DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP)
- | (1 << GET_DEVICE_STATUS)
- | (1 << GET_INTERFACE_STATUS)
+ writel(BIT(SET_TEST_MODE) |
+ BIT(SET_ADDRESS) |
+ BIT(DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP) |
+ BIT(GET_DEVICE_STATUS) |
+ BIT(GET_INTERFACE_STATUS)
, &dev->usb->stdrsp);
- writel ( (1 << USB_ROOT_PORT_WAKEUP_ENABLE)
- | (1 << SELF_POWERED_USB_DEVICE)
- | (1 << REMOTE_WAKEUP_SUPPORT)
- | (dev->softconnect << USB_DETECT_ENABLE)
- | (1 << SELF_POWERED_STATUS)
- , &dev->usb->usbctl);
+ writel(BIT(USB_ROOT_PORT_WAKEUP_ENABLE) |
+ BIT(SELF_POWERED_USB_DEVICE) |
+ BIT(REMOTE_WAKEUP_SUPPORT) |
+ (dev->softconnect << USB_DETECT_ENABLE) |
+ BIT(SELF_POWERED_STATUS),
+ &dev->usb->usbctl);
/* enable irqs so we can see ep0 and general operation */
- writel ( (1 << SETUP_PACKET_INTERRUPT_ENABLE)
- | (1 << ENDPOINT_0_INTERRUPT_ENABLE)
- , &dev->regs->pciirqenb0);
- writel ( (1 << PCI_INTERRUPT_ENABLE)
- | (1 << PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE)
- | (1 << PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE)
- | (1 << PCI_RETRY_ABORT_INTERRUPT_ENABLE)
- | (1 << VBUS_INTERRUPT_ENABLE)
- | (1 << ROOT_PORT_RESET_INTERRUPT_ENABLE)
- | (1 << SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE)
- , &dev->regs->pciirqenb1);
+ writel(BIT(SETUP_PACKET_INTERRUPT_ENABLE) |
+ BIT(ENDPOINT_0_INTERRUPT_ENABLE),
+ &dev->regs->pciirqenb0);
+ writel(BIT(PCI_INTERRUPT_ENABLE) |
+ BIT(PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE) |
+ BIT(PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE) |
+ BIT(PCI_RETRY_ABORT_INTERRUPT_ENABLE) |
+ BIT(VBUS_INTERRUPT_ENABLE) |
+ BIT(ROOT_PORT_RESET_INTERRUPT_ENABLE) |
+ BIT(SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE),
+ &dev->regs->pciirqenb1);
/* don't leave any writes posted */
(void) readl (&dev->usb->usbctl);
INFO(dev, "%s: Defect 7374 FsmValue %08x\n", __func__,
fsmvalue);
else
- writel((1 << CLEAR_NAK_OUT_PACKETS_MODE) |
- (1 << SET_EP_HIDE_STATUS_PHASE),
+ writel(BIT(CLEAR_NAK_OUT_PACKETS_MODE) |
+ BIT(SET_EP_HIDE_STATUS_PHASE),
&dev->epregs[0].ep_rsp);
/*
* endpoint status/features are handled in software, to
* help pass tests for some dubious behavior.
*/
- writel((1 << SET_ISOCHRONOUS_DELAY) |
- (1 << SET_SEL) |
- (1 << SET_TEST_MODE) |
- (1 << SET_ADDRESS) |
- (1 << GET_INTERFACE_STATUS) |
- (1 << GET_DEVICE_STATUS),
+ writel(BIT(SET_ISOCHRONOUS_DELAY) |
+ BIT(SET_SEL) |
+ BIT(SET_TEST_MODE) |
+ BIT(SET_ADDRESS) |
+ BIT(GET_INTERFACE_STATUS) |
+ BIT(GET_DEVICE_STATUS),
&dev->usb->stdrsp);
dev->wakeup_enable = 1;
- writel((1 << USB_ROOT_PORT_WAKEUP_ENABLE) |
+ writel(BIT(USB_ROOT_PORT_WAKEUP_ENABLE) |
(dev->softconnect << USB_DETECT_ENABLE) |
- (1 << DEVICE_REMOTE_WAKEUP_ENABLE),
+ BIT(DEVICE_REMOTE_WAKEUP_ENABLE),
&dev->usb->usbctl);
/* enable irqs so we can see ep0 and general operation */
- writel((1 << SETUP_PACKET_INTERRUPT_ENABLE) |
- (1 << ENDPOINT_0_INTERRUPT_ENABLE)
+ writel(BIT(SETUP_PACKET_INTERRUPT_ENABLE) |
+ BIT(ENDPOINT_0_INTERRUPT_ENABLE)
, &dev->regs->pciirqenb0);
- writel((1 << PCI_INTERRUPT_ENABLE) |
- (1 << ROOT_PORT_RESET_INTERRUPT_ENABLE) |
- (1 << SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE) |
- (1 << VBUS_INTERRUPT_ENABLE),
+ writel(BIT(PCI_INTERRUPT_ENABLE) |
+ BIT(ROOT_PORT_RESET_INTERRUPT_ENABLE) |
+ BIT(SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE) |
+ BIT(VBUS_INTERRUPT_ENABLE),
&dev->regs->pciirqenb1);
/* don't leave any writes posted */
/* Enable force-full-speed testing mode, if desired */
if (full_speed && dev->pdev->vendor == PCI_VENDOR_ID_PLX_LEGACY)
- writel(1 << FORCE_FULL_SPEED_MODE, &dev->usb->xcvrdiag);
+ writel(BIT(FORCE_FULL_SPEED_MODE), &dev->usb->xcvrdiag);
/* ... then enable host detection and ep0; and we're ready
* for set_configuration as well as eventual disconnect.
ep->ep.name, t, req ? &req->req : 0);
#endif
if (!ep->is_in || ep->dev->pdev->device == 0x2280)
- writel (t & ~(1 << NAK_OUT_PACKETS), &ep->regs->ep_stat);
+ writel(t & ~BIT(NAK_OUT_PACKETS), &ep->regs->ep_stat);
else
/* Added for 2282 */
writel (t, &ep->regs->ep_stat);
if (unlikely (ep->num == 0)) {
if (ep->is_in) {
/* status; stop NAKing */
- if (t & (1 << DATA_OUT_PING_TOKEN_INTERRUPT)) {
+ if (t & BIT(DATA_OUT_PING_TOKEN_INTERRUPT)) {
if (ep->dev->protocol_stall) {
ep->stopped = 1;
set_halt (ep);
allow_status (ep);
mode = 2;
/* reply to extra IN data tokens with a zlp */
- } else if (t & (1 << DATA_IN_TOKEN_INTERRUPT)) {
+ } else if (t & BIT(DATA_IN_TOKEN_INTERRUPT)) {
if (ep->dev->protocol_stall) {
ep->stopped = 1;
set_halt (ep);
}
} else {
/* status; stop NAKing */
- if (t & (1 << DATA_IN_TOKEN_INTERRUPT)) {
+ if (t & BIT(DATA_IN_TOKEN_INTERRUPT)) {
if (ep->dev->protocol_stall) {
ep->stopped = 1;
set_halt (ep);
}
mode = 2;
/* an extra OUT token is an error */
- } else if (((t & (1 << DATA_OUT_PING_TOKEN_INTERRUPT))
+ } else if (((t & BIT(DATA_OUT_PING_TOKEN_INTERRUPT))
&& req
&& req->req.actual == req->req.length)
|| (ep->responded && !req)) {
/* manual DMA queue advance after short OUT */
if (likely (ep->dma)) {
- if (t & (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT)) {
+ if (t & BIT(SHORT_PACKET_TRANSFERRED_INTERRUPT)) {
u32 count;
int stopped = ep->stopped;
/* here either (M < N), a "real" short rx;
* or (M == N) and the queue didn't empty
*/
- if (likely (t & (1 << FIFO_EMPTY))) {
+ if (likely(t & BIT(FIFO_EMPTY))) {
count = readl (&ep->dma->dmacount);
count &= DMA_BYTE_COUNT_MASK;
if (readl (&ep->dma->dmadesc)
}
/* stop DMA, leave ep NAKing */
- writel ((1 << DMA_ABORT), &ep->dma->dmastat);
+ writel(BIT(DMA_ABORT), &ep->dma->dmastat);
spin_stop_dma (ep->dma);
if (likely (req)) {
return;
/* data packet(s) received (in the fifo, OUT) */
- } else if (t & (1 << DATA_PACKET_RECEIVED_INTERRUPT)) {
+ } else if (t & BIT(DATA_PACKET_RECEIVED_INTERRUPT)) {
if (read_fifo (ep, req) && ep->num != 0)
mode = 2;
/* data packet(s) transmitted (IN) */
- } else if (t & (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)) {
+ } else if (t & BIT(DATA_PACKET_TRANSMITTED_INTERRUPT)) {
unsigned len;
len = req->req.length - req->req.actual;
if (req && !ep->stopped) {
/* load IN fifo with next packet (may be zlp) */
- if (t & (1 << DATA_PACKET_TRANSMITTED_INTERRUPT))
+ if (t & BIT(DATA_PACKET_TRANSMITTED_INTERRUPT))
write_fifo (ep, &req->req);
}
}
return;
/* This is the first Control Read for this connection: */
- if (!(readl(&dev->usb->usbstat) & (1 << SUPER_SPEED_MODE))) {
+ if (!(readl(&dev->usb->usbstat) & BIT(SUPER_SPEED_MODE))) {
/*
* Connection is NOT SS:
* - Connection must be FS or HS.
static const u32 ep_pl[9] = { 0, 3, 4, 7, 8, 2, 5, 6, 9 };
if (stall) {
- writel((1 << SET_ENDPOINT_HALT) |
- /* (1 << SET_NAK_PACKETS) | */
- (1 << CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE),
+ writel(BIT(SET_ENDPOINT_HALT) |
+ /* BIT(SET_NAK_PACKETS) | */
+ BIT(CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE),
&ep->regs->ep_rsp);
ep->is_halt = 1;
} else {
val = (val & ~0x1f) | ep_pl[ep->num];
writel(val, &dev->plregs->pl_ep_ctrl);
- val |= (1 << SEQUENCE_NUMBER_RESET);
+ val |= BIT(SEQUENCE_NUMBER_RESET);
writel(val, &dev->plregs->pl_ep_ctrl);
}
val = readl(&ep->regs->ep_rsp);
- val |= (1 << CLEAR_ENDPOINT_HALT) |
- (1 << CLEAR_ENDPOINT_TOGGLE);
+ val |= BIT(CLEAR_ENDPOINT_HALT) |
+ BIT(CLEAR_ENDPOINT_TOGGLE);
writel(val
- /* | (1 << CLEAR_NAK_PACKETS)*/
+ /* | BIT(CLEAR_NAK_PACKETS)*/
, &ep->regs->ep_rsp);
ep->is_halt = 0;
val = readl(&ep->regs->ep_rsp);
case (USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE):
status = dev->wakeup_enable ? 0x02 : 0x00;
if (dev->selfpowered)
- status |= 1 << 0;
+ status |= BIT(0);
status |= (dev->u1_enable << 2 | dev->u2_enable << 3 |
dev->ltm_enable << 4);
writel(0, &dev->epregs[0].ep_irqenb);
if (!e)
goto do_stall3;
status = readl(&e->regs->ep_rsp) &
- (1 << CLEAR_ENDPOINT_HALT);
+ BIT(CLEAR_ENDPOINT_HALT);
writel(0, &dev->epregs[0].ep_irqenb);
set_fifo_bytecount(ep, sizeof(status));
writel((__force u32) status, &dev->epregs[0].ep_data);
case USB_DEVICE_U1_ENABLE:
dev->u1_enable = 0;
writel(readl(&dev->usb_ext->usbctl2) &
- ~(1 << U1_ENABLE),
+ ~BIT(U1_ENABLE),
&dev->usb_ext->usbctl2);
allow_status_338x(ep);
goto next_endpoints3;
case USB_DEVICE_U2_ENABLE:
dev->u2_enable = 0;
writel(readl(&dev->usb_ext->usbctl2) &
- ~(1 << U2_ENABLE),
+ ~BIT(U2_ENABLE),
&dev->usb_ext->usbctl2);
allow_status_338x(ep);
goto next_endpoints3;
case USB_DEVICE_LTM_ENABLE:
dev->ltm_enable = 0;
writel(readl(&dev->usb_ext->usbctl2) &
- ~(1 << LTM_ENABLE),
+ ~BIT(LTM_ENABLE),
&dev->usb_ext->usbctl2);
allow_status_338x(ep);
goto next_endpoints3;
if (w_value == USB_DEVICE_REMOTE_WAKEUP) {
dev->wakeup_enable = 0;
writel(readl(&dev->usb->usbctl) &
- ~(1 << DEVICE_REMOTE_WAKEUP_ENABLE),
+ ~BIT(DEVICE_REMOTE_WAKEUP_ENABLE),
&dev->usb->usbctl);
allow_status_338x(ep);
break;
case USB_DEVICE_U1_ENABLE:
dev->u1_enable = 1;
writel(readl(&dev->usb_ext->usbctl2) |
- (1 << U1_ENABLE),
+ BIT(U1_ENABLE),
&dev->usb_ext->usbctl2);
allow_status_338x(ep);
goto next_endpoints3;
case USB_DEVICE_U2_ENABLE:
dev->u2_enable = 1;
writel(readl(&dev->usb_ext->usbctl2) |
- (1 << U2_ENABLE),
+ BIT(U2_ENABLE),
&dev->usb_ext->usbctl2);
allow_status_338x(ep);
goto next_endpoints3;
case USB_DEVICE_LTM_ENABLE:
dev->ltm_enable = 1;
writel(readl(&dev->usb_ext->usbctl2) |
- (1 << LTM_ENABLE),
+ BIT(LTM_ENABLE),
&dev->usb_ext->usbctl2);
allow_status_338x(ep);
goto next_endpoints3;
if (w_value == USB_DEVICE_REMOTE_WAKEUP) {
dev->wakeup_enable = 1;
writel(readl(&dev->usb->usbctl) |
- (1 << DEVICE_REMOTE_WAKEUP_ENABLE),
+ BIT(DEVICE_REMOTE_WAKEUP_ENABLE),
&dev->usb->usbctl);
allow_status_338x(ep);
break;
u32 num, scratch;
/* most of these don't need individual acks */
- stat &= ~(1 << INTA_ASSERTED);
+ stat &= ~BIT(INTA_ASSERTED);
if (!stat)
return;
// DEBUG (dev, "irqstat0 %04x\n", stat);
/* starting a control request? */
- if (unlikely (stat & (1 << SETUP_PACKET_INTERRUPT))) {
+ if (unlikely(stat & BIT(SETUP_PACKET_INTERRUPT))) {
union {
u32 raw [2];
struct usb_ctrlrequest r;
if (dev->gadget.speed == USB_SPEED_UNKNOWN) {
u32 val = readl(&dev->usb->usbstat);
- if (val & (1 << SUPER_SPEED)) {
+ if (val & BIT(SUPER_SPEED)) {
dev->gadget.speed = USB_SPEED_SUPER;
usb_ep_set_maxpacket_limit(&dev->ep[0].ep,
EP0_SS_MAX_PACKET_SIZE);
- } else if (val & (1 << HIGH_SPEED)) {
+ } else if (val & BIT(HIGH_SPEED)) {
dev->gadget.speed = USB_SPEED_HIGH;
usb_ep_set_maxpacket_limit(&dev->ep[0].ep,
EP0_HS_MAX_PACKET_SIZE);
ep->irqs++;
/* make sure any leftover request state is cleared */
- stat &= ~(1 << ENDPOINT_0_INTERRUPT);
+ stat &= ~BIT(ENDPOINT_0_INTERRUPT);
while (!list_empty (&ep->queue)) {
req = list_entry (ep->queue.next,
struct net2280_request, queue);
ep->is_halt = 0;
else{
if (ep->dev->pdev->device == 0x2280)
- tmp = (1 << FIFO_OVERFLOW) |
- (1 << FIFO_UNDERFLOW);
+ tmp = BIT(FIFO_OVERFLOW) |
+ BIT(FIFO_UNDERFLOW);
else
tmp = 0;
- writel(tmp | (1 << TIMEOUT) |
- (1 << USB_STALL_SENT) |
- (1 << USB_IN_NAK_SENT) |
- (1 << USB_IN_ACK_RCVD) |
- (1 << USB_OUT_PING_NAK_SENT) |
- (1 << USB_OUT_ACK_SENT) |
- (1 << SHORT_PACKET_OUT_DONE_INTERRUPT) |
- (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT) |
- (1 << DATA_PACKET_RECEIVED_INTERRUPT) |
- (1 << DATA_PACKET_TRANSMITTED_INTERRUPT) |
- (1 << DATA_OUT_PING_TOKEN_INTERRUPT) |
- (1 << DATA_IN_TOKEN_INTERRUPT)
+ writel(tmp | BIT(TIMEOUT) |
+ BIT(USB_STALL_SENT) |
+ BIT(USB_IN_NAK_SENT) |
+ BIT(USB_IN_ACK_RCVD) |
+ BIT(USB_OUT_PING_NAK_SENT) |
+ BIT(USB_OUT_ACK_SENT) |
+ BIT(SHORT_PACKET_OUT_DONE_INTERRUPT) |
+ BIT(SHORT_PACKET_TRANSFERRED_INTERRUPT) |
+ BIT(DATA_PACKET_RECEIVED_INTERRUPT) |
+ BIT(DATA_PACKET_TRANSMITTED_INTERRUPT) |
+ BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
+ BIT(DATA_IN_TOKEN_INTERRUPT)
, &ep->regs->ep_stat);
}
u.raw[0] = readl(&dev->usb->setup0123);
#define w_length le16_to_cpu(u.r.wLength)
/* ack the irq */
- writel (1 << SETUP_PACKET_INTERRUPT, &dev->regs->irqstat0);
- stat ^= (1 << SETUP_PACKET_INTERRUPT);
+ writel(BIT(SETUP_PACKET_INTERRUPT), &dev->regs->irqstat0);
+ stat ^= BIT(SETUP_PACKET_INTERRUPT);
/* watch control traffic at the token level, and force
* synchronization before letting the status stage happen.
*/
ep->is_in = (u.r.bRequestType & USB_DIR_IN) != 0;
if (ep->is_in) {
- scratch = (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)
- | (1 << DATA_OUT_PING_TOKEN_INTERRUPT)
- | (1 << DATA_IN_TOKEN_INTERRUPT);
+ scratch = BIT(DATA_PACKET_TRANSMITTED_INTERRUPT) |
+ BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
+ BIT(DATA_IN_TOKEN_INTERRUPT);
stop_out_naking (ep);
} else
- scratch = (1 << DATA_PACKET_RECEIVED_INTERRUPT)
- | (1 << DATA_OUT_PING_TOKEN_INTERRUPT)
- | (1 << DATA_IN_TOKEN_INTERRUPT);
+ scratch = BIT(DATA_PACKET_RECEIVED_INTERRUPT) |
+ BIT(DATA_OUT_PING_TOKEN_INTERRUPT) |
+ BIT(DATA_IN_TOKEN_INTERRUPT);
writel (scratch, &dev->epregs [0].ep_irqenb);
/* we made the hardware handle most lowlevel requests;
|| w_length > 2)
goto do_stall;
- if (readl (&e->regs->ep_rsp)
- & (1 << SET_ENDPOINT_HALT))
+ if (readl(&e->regs->ep_rsp) & BIT(SET_ENDPOINT_HALT))
status = cpu_to_le32 (1);
else
status = cpu_to_le32 (0);
u32 t;
/* do this endpoint's FIFO and queue need tending? */
- t = 1 << num;
+ t = BIT(num);
if ((scratch & t) == 0)
continue;
scratch ^= t;
DEBUG (dev, "unhandled irqstat0 %08x\n", stat);
}
-#define DMA_INTERRUPTS ( \
- (1 << DMA_D_INTERRUPT) \
- | (1 << DMA_C_INTERRUPT) \
- | (1 << DMA_B_INTERRUPT) \
- | (1 << DMA_A_INTERRUPT))
+#define DMA_INTERRUPTS (BIT(DMA_D_INTERRUPT) | \
+ BIT(DMA_C_INTERRUPT) | \
+ BIT(DMA_B_INTERRUPT) | \
+ BIT(DMA_A_INTERRUPT))
#define PCI_ERROR_INTERRUPTS ( \
- (1 << PCI_MASTER_ABORT_RECEIVED_INTERRUPT) \
- | (1 << PCI_TARGET_ABORT_RECEIVED_INTERRUPT) \
- | (1 << PCI_RETRY_ABORT_INTERRUPT))
+ BIT(PCI_MASTER_ABORT_RECEIVED_INTERRUPT) | \
+ BIT(PCI_TARGET_ABORT_RECEIVED_INTERRUPT) | \
+ BIT(PCI_RETRY_ABORT_INTERRUPT))
static void handle_stat1_irqs (struct net2280 *dev, u32 stat)
{
u32 tmp, num, mask, scratch;
/* after disconnect there's nothing else to do! */
- tmp = (1 << VBUS_INTERRUPT) | (1 << ROOT_PORT_RESET_INTERRUPT);
- mask = (1 << SUPER_SPEED) | (1 << HIGH_SPEED) | (1 << FULL_SPEED);
+ tmp = BIT(VBUS_INTERRUPT) | BIT(ROOT_PORT_RESET_INTERRUPT);
+ mask = BIT(SUPER_SPEED) | BIT(HIGH_SPEED) | BIT(FULL_SPEED);
/* VBUS disconnect is indicated by VBUS_PIN and VBUS_INTERRUPT set.
* Root Port Reset is indicated by ROOT_PORT_RESET_INTERRUPT set and
*/
if (stat & tmp) {
writel (tmp, &dev->regs->irqstat1);
- if ((((stat & (1 << ROOT_PORT_RESET_INTERRUPT))
+ if ((((stat & BIT(ROOT_PORT_RESET_INTERRUPT))
&& ((readl (&dev->usb->usbstat) & mask)
== 0))
|| ((readl (&dev->usb->usbctl)
- & (1 << VBUS_PIN)) == 0)
+ & BIT(VBUS_PIN)) == 0)
) && ( dev->gadget.speed != USB_SPEED_UNKNOWN)) {
DEBUG (dev, "disconnect %s\n",
dev->driver->driver.name);
/* NOTE: chip stays in PCI D0 state for now, but it could
* enter D1 to save more power
*/
- tmp = (1 << SUSPEND_REQUEST_CHANGE_INTERRUPT);
+ tmp = BIT(SUSPEND_REQUEST_CHANGE_INTERRUPT);
if (stat & tmp) {
writel (tmp, &dev->regs->irqstat1);
- if (stat & (1 << SUSPEND_REQUEST_INTERRUPT)) {
+ if (stat & BIT(SUSPEND_REQUEST_INTERRUPT)) {
if (dev->driver->suspend)
dev->driver->suspend (&dev->gadget);
if (!enable_suspend)
- stat &= ~(1 << SUSPEND_REQUEST_INTERRUPT);
+ stat &= ~BIT(SUSPEND_REQUEST_INTERRUPT);
} else {
if (dev->driver->resume)
dev->driver->resume (&dev->gadget);
/* some status we can just ignore */
if (dev->pdev->device == 0x2280)
- stat &= ~((1 << CONTROL_STATUS_INTERRUPT)
- | (1 << SUSPEND_REQUEST_INTERRUPT)
- | (1 << RESUME_INTERRUPT)
- | (1 << SOF_INTERRUPT));
+ stat &= ~(BIT(CONTROL_STATUS_INTERRUPT) |
+ BIT(SUSPEND_REQUEST_INTERRUPT) |
+ BIT(RESUME_INTERRUPT) |
+ BIT(SOF_INTERRUPT));
else
- stat &= ~((1 << CONTROL_STATUS_INTERRUPT)
- | (1 << RESUME_INTERRUPT)
- | (1 << SOF_DOWN_INTERRUPT)
- | (1 << SOF_INTERRUPT));
+ stat &= ~(BIT(CONTROL_STATUS_INTERRUPT) |
+ BIT(RESUME_INTERRUPT) |
+ BIT(SOF_DOWN_INTERRUPT) |
+ BIT(SOF_INTERRUPT));
if (!stat)
return;
for (num = 0; scratch; num++) {
struct net2280_dma_regs __iomem *dma;
- tmp = 1 << num;
+ tmp = BIT(num);
if ((tmp & scratch) == 0)
continue;
scratch ^= tmp;
if (dev->pdev->vendor == PCI_VENDOR_ID_PLX) {
u32 r_dmacount = readl(&dma->dmacount);
if (!ep->is_in && (r_dmacount & 0x00FFFFFF) &&
- (tmp & (1 << DMA_TRANSACTION_DONE_INTERRUPT)))
+ (tmp & BIT(DMA_TRANSACTION_DONE_INTERRUPT)))
continue;
}
* or (stat0 codepath) short OUT transfer.
*/
if (!use_dma_chaining) {
- if (!(tmp & (1 << DMA_TRANSACTION_DONE_INTERRUPT))) {
+ if (!(tmp & BIT(DMA_TRANSACTION_DONE_INTERRUPT))) {
DEBUG (ep->dev, "%s no xact done? %08x\n",
ep->ep.name, tmp);
continue;
stop_dma (ep->dma);
} else {
tmp = readl (&dma->dmactl);
- if (!use_dma_chaining
- || (tmp & (1 << DMA_ENABLE)) == 0)
+ if (!use_dma_chaining || (tmp & BIT(DMA_ENABLE)) == 0)
restart_dma (ep);
else if (ep->is_in && use_dma_chaining) {
struct net2280_request *req;
req = list_entry (ep->queue.next,
struct net2280_request, queue);
dmacount = req->td->dmacount;
- dmacount &= cpu_to_le32 (
- (1 << VALID_BIT)
- | DMA_BYTE_COUNT_MASK);
+ dmacount &= cpu_to_le32(BIT(VALID_BIT) |
+ DMA_BYTE_COUNT_MASK);
if (dmacount && (dmacount & valid_bit) == 0)
restart_dma (ep);
}
/* shared interrupt, not ours */
if (dev->pdev->vendor == PCI_VENDOR_ID_PLX_LEGACY &&
- (!(readl(&dev->regs->irqstat0) & (1 << INTA_ASSERTED))))
+ (!(readl(&dev->regs->irqstat0) & BIT(INTA_ASSERTED))))
return IRQ_NONE;
spin_lock (&dev->lock);
dev->plregs = (struct usb338x_pl_regs __iomem *)
(base + 0x0800);
usbstat = readl(&dev->usb->usbstat);
- dev->enhanced_mode = (usbstat & (1 << 11)) ? 1 : 0;
+ dev->enhanced_mode = (usbstat & BIT(11)) ? 1 : 0;
dev->n_ep = (dev->enhanced_mode) ? 9 : 5;
/* put into initial config, link up all endpoints */
fsmvalue = get_idx_reg(dev->regs, SCRATCH) &
/* enable lower-overhead pci memory bursts during DMA */
if (dev->pdev->vendor == PCI_VENDOR_ID_PLX_LEGACY)
- writel((1 << DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE)
- // 256 write retries may not be enough...
- // | (1 << PCI_RETRY_ABORT_ENABLE)
- | (1 << DMA_READ_MULTIPLE_ENABLE)
- | (1 << DMA_READ_LINE_ENABLE)
- , &dev->pci->pcimstctl);
+ writel(BIT(DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE) |
+ /*
+ * 256 write retries may not be enough...
+ BIT(PCI_RETRY_ABORT_ENABLE) |
+ */
+ BIT(DMA_READ_MULTIPLE_ENABLE) |
+ BIT(DMA_READ_LINE_ENABLE),
+ &dev->pci->pcimstctl);
/* erratum 0115 shouldn't appear: Linux inits PCI_LATENCY_TIMER */
pci_set_master (pdev);
pci_try_set_mwi (pdev);
git.openpandora.org / pandora-kernel.git / commitdiff