exynos: spl: Add a custom spi copy function
authorRajeshwari Shinde <rajeshwari.s@samsung.com>
Tue, 8 Oct 2013 13:12:22 +0000 (18:42 +0530)
committerMinkyu Kang <mk7.kang@samsung.com>
Tue, 3 Dec 2013 06:26:33 +0000 (15:26 +0900)
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.

Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
arch/arm/cpu/armv7/exynos/pinmux.c
arch/arm/cpu/armv7/exynos/spl_boot.c
arch/arm/include/asm/arch-exynos/spi.h
include/configs/exynos5250-dt.h

index 8002bce..74cc700 100644 (file)
@@ -462,7 +462,7 @@ static int exynos4_pinmux_config(int peripheral, int flags)
        case PERIPH_ID_SDMMC1:
        case PERIPH_ID_SDMMC3:
        case PERIPH_ID_SDMMC4:
-               printf("SDMMC device %d not implemented\n", peripheral);
+               debug("SDMMC device %d not implemented\n", peripheral);
                return -1;
        default:
                debug("%s: invalid peripheral %d", __func__, peripheral);
index 3651c00..6faf13f 100644 (file)
 #include <asm/arch/clock.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/dmc.h>
+#include <asm/arch/periph.h>
+#include <asm/arch/pinmux.h>
 #include <asm/arch/power.h>
 #include <asm/arch/spl.h>
+#include <asm/arch/spi.h>
 
 #include "common_setup.h"
 #include "clock_init.h"
@@ -59,6 +62,119 @@ static int config_branch_prediction(int set_cr_z)
 }
 #endif
 
+static void spi_rx_tx(struct exynos_spi *regs, int todo,
+                       void *dinp, void const *doutp, int i)
+{
+       uint *rxp = (uint *)(dinp + (i * (32 * 1024)));
+       int rx_lvl, tx_lvl;
+       uint out_bytes, in_bytes;
+
+       out_bytes = todo;
+       in_bytes = todo;
+       setbits_le32(&regs->ch_cfg, SPI_CH_RST);
+       clrbits_le32(&regs->ch_cfg, SPI_CH_RST);
+       writel(((todo * 8) / 32) | SPI_PACKET_CNT_EN, &regs->pkt_cnt);
+
+       while (in_bytes) {
+               uint32_t spi_sts;
+               int temp;
+
+               spi_sts = readl(&regs->spi_sts);
+               rx_lvl = ((spi_sts >> 15) & 0x7f);
+               tx_lvl = ((spi_sts >> 6) & 0x7f);
+               while (tx_lvl < 32 && out_bytes) {
+                       temp = 0xffffffff;
+                       writel(temp, &regs->tx_data);
+                       out_bytes -= 4;
+                       tx_lvl += 4;
+               }
+               while (rx_lvl >= 4 && in_bytes) {
+                       temp = readl(&regs->rx_data);
+                       if (rxp)
+                               *rxp++ = temp;
+                       in_bytes -= 4;
+                       rx_lvl -= 4;
+               }
+       }
+}
+
+/*
+ * Copy uboot from spi flash to RAM
+ *
+ * @parma uboot_size   size of u-boot to copy
+ * @param uboot_addr   address in u-boot to copy
+ */
+static void exynos_spi_copy(unsigned int uboot_size, unsigned int uboot_addr)
+{
+       int upto, todo;
+       int i, timeout = 100;
+       struct exynos_spi *regs = (struct exynos_spi *)CONFIG_ENV_SPI_BASE;
+
+       set_spi_clk(PERIPH_ID_SPI1, 50000000); /* set spi clock to 50Mhz */
+       /* set the spi1 GPIO */
+       exynos_pinmux_config(PERIPH_ID_SPI1, PINMUX_FLAG_NONE);
+
+       /* set pktcnt and enable it */
+       writel(4 | SPI_PACKET_CNT_EN, &regs->pkt_cnt);
+       /* set FB_CLK_SEL */
+       writel(SPI_FB_DELAY_180, &regs->fb_clk);
+       /* set CH_WIDTH and BUS_WIDTH as word */
+       setbits_le32(&regs->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
+                                       SPI_MODE_BUS_WIDTH_WORD);
+       clrbits_le32(&regs->ch_cfg, SPI_CH_CPOL_L); /* CPOL: active high */
+
+       /* clear rx and tx channel if set priveously */
+       clrbits_le32(&regs->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON);
+
+       setbits_le32(&regs->swap_cfg, SPI_RX_SWAP_EN |
+                       SPI_RX_BYTE_SWAP |
+                       SPI_RX_HWORD_SWAP);
+
+       /* do a soft reset */
+       setbits_le32(&regs->ch_cfg, SPI_CH_RST);
+       clrbits_le32(&regs->ch_cfg, SPI_CH_RST);
+
+       /* now set rx and tx channel ON */
+       setbits_le32(&regs->ch_cfg, SPI_RX_CH_ON | SPI_TX_CH_ON | SPI_CH_HS_EN);
+       clrbits_le32(&regs->cs_reg, SPI_SLAVE_SIG_INACT); /* CS low */
+
+       /* Send read instruction (0x3h) followed by a 24 bit addr */
+       writel((SF_READ_DATA_CMD << 24) | SPI_FLASH_UBOOT_POS, &regs->tx_data);
+
+       /* waiting for TX done */
+       while (!(readl(&regs->spi_sts) & SPI_ST_TX_DONE)) {
+               if (!timeout) {
+                       debug("SPI TIMEOUT\n");
+                       break;
+               }
+               timeout--;
+       }
+
+       for (upto = 0, i = 0; upto < uboot_size; upto += todo, i++) {
+               todo = min(uboot_size - upto, (1 << 15));
+               spi_rx_tx(regs, todo, (void *)(uboot_addr),
+                         (void *)(SPI_FLASH_UBOOT_POS), i);
+       }
+
+       setbits_le32(&regs->cs_reg, SPI_SLAVE_SIG_INACT);/* make the CS high */
+
+       /*
+        * Let put controller mode to BYTE as
+        * SPI driver does not support WORD mode yet
+        */
+       clrbits_le32(&regs->mode_cfg, SPI_MODE_CH_WIDTH_WORD |
+                                       SPI_MODE_BUS_WIDTH_WORD);
+       writel(0, &regs->swap_cfg);
+
+       /*
+        * Flush spi tx, rx fifos and reset the SPI controller
+        * and clear rx/tx channel
+        */
+       clrsetbits_le32(&regs->ch_cfg, SPI_CH_HS_EN, SPI_CH_RST);
+       clrbits_le32(&regs->ch_cfg, SPI_CH_RST);
+       clrbits_le32(&regs->ch_cfg, SPI_TX_CH_ON | SPI_RX_CH_ON);
+}
+
 /*
 * Copy U-boot from mmc to RAM:
 * COPY_BL2_FNPTR_ADDR: Address in iRAM, which Contains
@@ -70,6 +186,7 @@ void copy_uboot_to_ram(void)
 
        u32 (*copy_bl2)(u32 offset, u32 nblock, u32 dst) = NULL;
        u32 offset = 0, size = 0;
+       struct spl_machine_param *param = spl_get_machine_params();
 #ifdef CONFIG_SUPPORT_EMMC_BOOT
        u32 (*copy_bl2_from_emmc)(u32 nblock, u32 dst);
        void (*end_bootop_from_emmc)(void);
@@ -91,9 +208,8 @@ void copy_uboot_to_ram(void)
        switch (bootmode) {
 #ifdef CONFIG_SPI_BOOTING
        case BOOT_MODE_SERIAL:
-               offset = SPI_FLASH_UBOOT_POS;
-               size = CONFIG_BL2_SIZE;
-               copy_bl2 = get_irom_func(SPI_INDEX);
+               /* Customised function to copy u-boot from SF */
+               exynos_spi_copy(param->uboot_size, CONFIG_SYS_TEXT_BASE);
                break;
 #endif
        case BOOT_MODE_MMC:
index 147c1a7..0ba931b 100644 (file)
@@ -30,6 +30,7 @@ struct exynos_spi {
 #define EXYNOS_SPI_MAX_FREQ    50000000
 
 #define SPI_TIMEOUT_MS         10
+#define SF_READ_DATA_CMD       0x3
 
 /* SPI_CHCFG */
 #define SPI_CH_HS_EN           (1 << 6)
index 2bd91a5..dee18a7 100644 (file)
 #define COPY_BL2_FNPTR_ADDR    0x02020030
 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
 
 /* specific .lds file */
 #define CONFIG_SPL_LDSCRIPT    "board/samsung/common/exynos-uboot-spl.lds"
 /* SPI */
 #define CONFIG_ENV_IS_IN_SPI_FLASH
 #define CONFIG_SPI_FLASH
+#define CONFIG_ENV_SPI_BASE    0x12D30000
 
 #ifdef CONFIG_SPI_FLASH
 #define CONFIG_EXYNOS_SPI