prompt "ARM system type"
default ARCH_VERSATILE
-config ARCH_AAEC2000
- bool "Agilent AAEC-2000 based"
- select CPU_ARM920T
- select ARM_AMBA
- select HAVE_CLK
- select ARCH_USES_GETTIMEOFFSET
- help
- This enables support for systems based on the Agilent AAEC-2000
-
config ARCH_INTEGRATOR
bool "ARM Ltd. Integrator family"
select ARM_AMBA
# Kconfigs may be included either alphabetically (according to the
# plat- suffix) or along side the corresponding mach-* source.
#
-source "arch/arm/mach-aaec2000/Kconfig"
-
source "arch/arm/mach-at91/Kconfig"
source "arch/arm/mach-bcmring/Kconfig"
# Machine directory name. This list is sorted alphanumerically
# by CONFIG_* macro name.
-machine-$(CONFIG_ARCH_AAEC2000) := aaec2000
machine-$(CONFIG_ARCH_AT91) := at91
machine-$(CONFIG_ARCH_BCMRING) := bcmring
machine-$(CONFIG_ARCH_CLPS711X) := clps711x
+++ /dev/null
-if ARCH_AAEC2000
-
-menu "Agilent AAEC-2000 Implementations"
-
-config MACH_AAED2000
- bool "Agilent AAED-2000 Development Platform"
- select CPU_ARM920T
-
-endmenu
-
-endif
+++ /dev/null
-#
-# Makefile for the linux kernel.
-#
-
-# Common support (must be linked before board specific support)
-obj-y += core.o
-
-# Specific board support
-obj-$(CONFIG_MACH_AAED2000) += aaed2000.o
+++ /dev/null
- zreladdr-y := 0xf0008000
+++ /dev/null
-/*
- * linux/arch/arm/mach-aaec2000/aaed2000.c
- *
- * Support for the Agilent AAED-2000 Development Platform.
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/major.h>
-#include <linux/interrupt.h>
-
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <asm/mach-types.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/aaed2000.h>
-
-#include "core.h"
-
-static void aaed2000_clcd_disable(struct clcd_fb *fb)
-{
- AAED_EXT_GPIO &= ~AAED_EGPIO_LCD_PWR_EN;
-}
-
-static void aaed2000_clcd_enable(struct clcd_fb *fb)
-{
- AAED_EXT_GPIO |= AAED_EGPIO_LCD_PWR_EN;
-}
-
-struct aaec2000_clcd_info clcd_info = {
- .enable = aaed2000_clcd_enable,
- .disable = aaed2000_clcd_disable,
- .panel = {
- .mode = {
- .name = "Sharp",
- .refresh = 60,
- .xres = 640,
- .yres = 480,
- .pixclock = 39721,
- .left_margin = 20,
- .right_margin = 44,
- .upper_margin = 21,
- .lower_margin = 34,
- .hsync_len = 96,
- .vsync_len = 2,
- .sync = 0,
- .vmode = FB_VMODE_NONINTERLACED,
- },
- .width = -1,
- .height = -1,
- .tim2 = TIM2_IVS | TIM2_IHS,
- .cntl = CNTL_LCDTFT,
- .bpp = 16,
- },
-};
-
-static void __init aaed2000_init_irq(void)
-{
- aaec2000_init_irq();
-}
-
-static void __init aaed2000_init(void)
-{
- aaec2000_set_clcd_plat_data(&clcd_info);
-}
-
-static struct map_desc aaed2000_io_desc[] __initdata = {
- {
- .virtual = EXT_GPIO_VBASE,
- .pfn = __phys_to_pfn(EXT_GPIO_PBASE),
- .length = EXT_GPIO_LENGTH,
- .type = MT_DEVICE
- },
-};
-
-static void __init aaed2000_map_io(void)
-{
- aaec2000_map_io();
- iotable_init(aaed2000_io_desc, ARRAY_SIZE(aaed2000_io_desc));
-}
-
-MACHINE_START(AAED2000, "Agilent AAED-2000 Development Platform")
- /* Maintainer: Nicolas Bellido Y Ortega */
- .map_io = aaed2000_map_io,
- .init_irq = aaed2000_init_irq,
- .timer = &aaec2000_timer,
- .init_machine = aaed2000_init,
-MACHINE_END
+++ /dev/null
-/*
- * linux/arch/arm/mach-aaec2000/core.c
- *
- * Code common to all AAEC-2000 machines
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/list.h>
-#include <linux/errno.h>
-#include <linux/dma-mapping.h>
-#include <linux/interrupt.h>
-#include <linux/timex.h>
-#include <linux/signal.h>
-#include <linux/clk.h>
-#include <linux/gfp.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/sizes.h>
-
-#include <asm/mach/flash.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-#include <asm/mach/map.h>
-
-#include "core.h"
-
-/*
- * Common I/O mapping:
- *
- * Static virtual address mappings are as follow:
- *
- * 0xf8000000-0xf8001ffff: Devices connected to APB bus
- * 0xf8002000-0xf8003ffff: Devices connected to AHB bus
- *
- * Below 0xe8000000 is reserved for vm allocation.
- *
- * The machine specific code must provide the extra mapping beside the
- * default mapping provided here.
- */
-static struct map_desc standard_io_desc[] __initdata = {
- {
- .virtual = VIO_APB_BASE,
- .pfn = __phys_to_pfn(PIO_APB_BASE),
- .length = IO_APB_LENGTH,
- .type = MT_DEVICE
- }, {
- .virtual = VIO_AHB_BASE,
- .pfn = __phys_to_pfn(PIO_AHB_BASE),
- .length = IO_AHB_LENGTH,
- .type = MT_DEVICE
- }
-};
-
-void __init aaec2000_map_io(void)
-{
- iotable_init(standard_io_desc, ARRAY_SIZE(standard_io_desc));
-}
-
-/*
- * Interrupt handling routines
- */
-static void aaec2000_int_ack(struct irq_data *d)
-{
- IRQ_INTSR = 1 << d->irq;
-}
-
-static void aaec2000_int_mask(struct irq_data *d)
-{
- IRQ_INTENC |= (1 << d->irq);
-}
-
-static void aaec2000_int_unmask(struct irq_data *d)
-{
- IRQ_INTENS |= (1 << d->irq);
-}
-
-static struct irq_chip aaec2000_irq_chip = {
- .irq_ack = aaec2000_int_ack,
- .irq_mask = aaec2000_int_mask,
- .irq_unmask = aaec2000_int_unmask,
-};
-
-void __init aaec2000_init_irq(void)
-{
- unsigned int i;
-
- for (i = 0; i < NR_IRQS; i++) {
- set_irq_handler(i, handle_level_irq);
- set_irq_chip(i, &aaec2000_irq_chip);
- set_irq_flags(i, IRQF_VALID);
- }
-
- /* Disable all interrupts */
- IRQ_INTENC = 0xffffffff;
-
- /* Clear any pending interrupts */
- IRQ_INTSR = IRQ_INTSR;
-}
-
-/*
- * Time keeping
- */
-/* IRQs are disabled before entering here from do_gettimeofday() */
-static unsigned long aaec2000_gettimeoffset(void)
-{
- unsigned long ticks_to_match, elapsed, usec;
-
- /* Get ticks before next timer match */
- ticks_to_match = TIMER1_LOAD - TIMER1_VAL;
-
- /* We need elapsed ticks since last match */
- elapsed = LATCH - ticks_to_match;
-
- /* Now, convert them to usec */
- usec = (unsigned long)(elapsed * (tick_nsec / 1000))/LATCH;
-
- return usec;
-}
-
-/* We enter here with IRQs enabled */
-static irqreturn_t
-aaec2000_timer_interrupt(int irq, void *dev_id)
-{
- /* TODO: Check timer accuracy */
- timer_tick();
- TIMER1_CLEAR = 1;
-
- return IRQ_HANDLED;
-}
-
-static struct irqaction aaec2000_timer_irq = {
- .name = "AAEC-2000 Timer Tick",
- .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
- .handler = aaec2000_timer_interrupt,
-};
-
-static void __init aaec2000_timer_init(void)
-{
- /* Disable timer 1 */
- TIMER1_CTRL = 0;
-
- /* We have somehow to generate a 100Hz clock.
- * We then use the 508KHz timer in periodic mode.
- */
- TIMER1_LOAD = LATCH;
- TIMER1_CLEAR = 1; /* Clear interrupt */
-
- setup_irq(INT_TMR1_OFL, &aaec2000_timer_irq);
-
- TIMER1_CTRL = TIMER_CTRL_ENABLE |
- TIMER_CTRL_PERIODIC |
- TIMER_CTRL_CLKSEL_508K;
-}
-
-struct sys_timer aaec2000_timer = {
- .init = aaec2000_timer_init,
- .offset = aaec2000_gettimeoffset,
-};
-
-static struct clcd_panel mach_clcd_panel;
-
-static int aaec2000_clcd_setup(struct clcd_fb *fb)
-{
- dma_addr_t dma;
-
- fb->panel = &mach_clcd_panel;
-
- fb->fb.screen_base = dma_alloc_writecombine(&fb->dev->dev, SZ_1M,
- &dma, GFP_KERNEL);
-
- if (!fb->fb.screen_base) {
- printk(KERN_ERR "CLCD: unable to map framebuffer\n");
- return -ENOMEM;
- }
-
- fb->fb.fix.smem_start = dma;
- fb->fb.fix.smem_len = SZ_1M;
-
- return 0;
-}
-
-static int aaec2000_clcd_mmap(struct clcd_fb *fb, struct vm_area_struct *vma)
-{
- return dma_mmap_writecombine(&fb->dev->dev, vma,
- fb->fb.screen_base,
- fb->fb.fix.smem_start,
- fb->fb.fix.smem_len);
-}
-
-static void aaec2000_clcd_remove(struct clcd_fb *fb)
-{
- dma_free_writecombine(&fb->dev->dev, fb->fb.fix.smem_len,
- fb->fb.screen_base, fb->fb.fix.smem_start);
-}
-
-static struct clcd_board clcd_plat_data = {
- .name = "AAEC-2000",
- .check = clcdfb_check,
- .decode = clcdfb_decode,
- .setup = aaec2000_clcd_setup,
- .mmap = aaec2000_clcd_mmap,
- .remove = aaec2000_clcd_remove,
-};
-
-static struct amba_device clcd_device = {
- .dev = {
- .init_name = "mb:16",
- .coherent_dma_mask = ~0,
- .platform_data = &clcd_plat_data,
- },
- .res = {
- .start = AAEC_CLCD_PHYS,
- .end = AAEC_CLCD_PHYS + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- .irq = { INT_LCD, NO_IRQ },
- .periphid = 0x41110,
-};
-
-static struct amba_device *amba_devs[] __initdata = {
- &clcd_device,
-};
-
-void clk_disable(struct clk *clk)
-{
-}
-
-int clk_set_rate(struct clk *clk, unsigned long rate)
-{
- return 0;
-}
-
-int clk_enable(struct clk *clk)
-{
- return 0;
-}
-
-struct clk *clk_get(struct device *dev, const char *id)
-{
- return dev && strcmp(dev_name(dev), "mb:16") == 0 ? NULL : ERR_PTR(-ENOENT);
-}
-
-void clk_put(struct clk *clk)
-{
-}
-
-void __init aaec2000_set_clcd_plat_data(struct aaec2000_clcd_info *clcd)
-{
- clcd_plat_data.enable = clcd->enable;
- clcd_plat_data.disable = clcd->disable;
- memcpy(&mach_clcd_panel, &clcd->panel, sizeof(struct clcd_panel));
-}
-
-static struct flash_platform_data aaec2000_flash_data = {
- .map_name = "cfi_probe",
- .width = 4,
-};
-
-static struct resource aaec2000_flash_resource = {
- .start = AAEC_FLASH_BASE,
- .end = AAEC_FLASH_BASE + AAEC_FLASH_SIZE,
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device aaec2000_flash_device = {
- .name = "armflash",
- .id = 0,
- .dev = {
- .platform_data = &aaec2000_flash_data,
- },
- .num_resources = 1,
- .resource = &aaec2000_flash_resource,
-};
-
-static int __init aaec2000_init(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(amba_devs); i++) {
- struct amba_device *d = amba_devs[i];
- amba_device_register(d, &iomem_resource);
- }
-
- platform_device_register(&aaec2000_flash_device);
-
- return 0;
-};
-arch_initcall(aaec2000_init);
-
+++ /dev/null
-/*
- * linux/arch/arm/mach-aaec2000/core.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-
-#include <linux/amba/bus.h>
-#include <linux/amba/clcd.h>
-
-struct sys_timer;
-
-extern struct sys_timer aaec2000_timer;
-extern void __init aaec2000_map_io(void);
-extern void __init aaec2000_init_irq(void);
-
-struct aaec2000_clcd_info {
- struct clcd_panel panel;
- void (*disable)(struct clcd_fb *);
- void (*enable)(struct clcd_fb *);
-};
-
-extern void __init aaec2000_set_clcd_plat_data(struct aaec2000_clcd_info *);
-
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/aaec2000.h
- *
- * AAEC-2000 registers definition
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_AAEC2000_H
-#define __ASM_ARCH_AAEC2000_H
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#error You must include hardware.h not this file
-#endif /* __ASM_ARCH_HARDWARE_H */
-
-/* Chip selects */
-#define AAEC_CS0 0x00000000
-#define AAEC_CS1 0x10000000
-#define AAEC_CS2 0x20000000
-#define AAEC_CS3 0x30000000
-
-/* Flash */
-#define AAEC_FLASH_BASE AAEC_CS0
-#define AAEC_FLASH_SIZE SZ_64M
-
-/* Interrupt controller */
-#define IRQ_BASE __REG(0x80000500)
-#define IRQ_INTSR __REG(0x80000500) /* Int Status Register */
-#define IRQ_INTRSR __REG(0x80000504) /* Int Raw (unmasked) Status */
-#define IRQ_INTENS __REG(0x80000508) /* Int Enable Set */
-#define IRQ_INTENC __REG(0x8000050c) /* Int Enable Clear */
-
-/* UART 1 */
-#define UART1_BASE __REG(0x80000600)
-#define UART1_DR __REG(0x80000600) /* Data/FIFO Register */
-#define UART1_LCR __REG(0x80000604) /* Link Control Register */
-#define UART1_BRCR __REG(0x80000608) /* Baud Rate Control Register */
-#define UART1_CR __REG(0x8000060c) /* Control Register */
-#define UART1_SR __REG(0x80000610) /* Status Register */
-#define UART1_INT __REG(0x80000614) /* Interrupt Status Register */
-#define UART1_INTM __REG(0x80000618) /* Interrupt Mask Register */
-#define UART1_INTRES __REG(0x8000061c) /* Int Result (masked status) Register */
-
-/* UART 2 */
-#define UART2_BASE __REG(0x80000700)
-#define UART2_DR __REG(0x80000700) /* Data/FIFO Register */
-#define UART2_LCR __REG(0x80000704) /* Link Control Register */
-#define UART2_BRCR __REG(0x80000708) /* Baud Rate Control Register */
-#define UART2_CR __REG(0x8000070c) /* Control Register */
-#define UART2_SR __REG(0x80000710) /* Status Register */
-#define UART2_INT __REG(0x80000714) /* Interrupt Status Register */
-#define UART2_INTM __REG(0x80000718) /* Interrupt Mask Register */
-#define UART2_INTRES __REG(0x8000071c) /* Int Result (masked status) Register */
-
-/* UART 3 */
-#define UART3_BASE __REG(0x80000800)
-#define UART3_DR __REG(0x80000800) /* Data/FIFO Register */
-#define UART3_LCR __REG(0x80000804) /* Link Control Register */
-#define UART3_BRCR __REG(0x80000808) /* Baud Rate Control Register */
-#define UART3_CR __REG(0x8000080c) /* Control Register */
-#define UART3_SR __REG(0x80000810) /* Status Register */
-#define UART3_INT __REG(0x80000814) /* Interrupt Status Register */
-#define UART3_INTM __REG(0x80000818) /* Interrupt Mask Register */
-#define UART3_INTRES __REG(0x8000081c) /* Int Result (masked status) Register */
-
-/* These are used in some places */
-#define _UART1_BASE __PREG(UART1_BASE)
-#define _UART2_BASE __PREG(UART2_BASE)
-#define _UART3_BASE __PREG(UART3_BASE)
-
-/* UART Registers Offsets */
-#define UART_DR 0x00
-#define UART_LCR 0x04
-#define UART_BRCR 0x08
-#define UART_CR 0x0c
-#define UART_SR 0x10
-#define UART_INT 0x14
-#define UART_INTM 0x18
-#define UART_INTRES 0x1c
-
-/* UART_LCR Bitmask */
-#define UART_LCR_BRK (1 << 0) /* Send Break */
-#define UART_LCR_PEN (1 << 1) /* Parity Enable */
-#define UART_LCR_EP (1 << 2) /* Even/Odd Parity */
-#define UART_LCR_S2 (1 << 3) /* One/Two Stop bits */
-#define UART_LCR_FIFO (1 << 4) /* FIFO Enable */
-#define UART_LCR_WL5 (0 << 5) /* Word Length - 5 bits */
-#define UART_LCR_WL6 (1 << 5) /* Word Length - 6 bits */
-#define UART_LCR_WL7 (1 << 6) /* Word Length - 7 bits */
-#define UART_LCR_WL8 (1 << 7) /* Word Length - 8 bits */
-
-/* UART_CR Bitmask */
-#define UART_CR_EN (1 << 0) /* UART Enable */
-#define UART_CR_SIR (1 << 1) /* IrDA SIR Enable */
-#define UART_CR_SIRLP (1 << 2) /* Low Power IrDA Enable */
-#define UART_CR_RXP (1 << 3) /* Receive Pin Polarity */
-#define UART_CR_TXP (1 << 4) /* Transmit Pin Polarity */
-#define UART_CR_MXP (1 << 5) /* Modem Pin Polarity */
-#define UART_CR_LOOP (1 << 6) /* Loopback Mode */
-
-/* UART_SR Bitmask */
-#define UART_SR_CTS (1 << 0) /* Clear To Send Status */
-#define UART_SR_DSR (1 << 1) /* Data Set Ready Status */
-#define UART_SR_DCD (1 << 2) /* Data Carrier Detect Status */
-#define UART_SR_TxBSY (1 << 3) /* Transmitter Busy Status */
-#define UART_SR_RxFE (1 << 4) /* Receive FIFO Empty Status */
-#define UART_SR_TxFF (1 << 5) /* Transmit FIFO Full Status */
-#define UART_SR_RxFF (1 << 6) /* Receive FIFO Full Status */
-#define UART_SR_TxFE (1 << 7) /* Transmit FIFO Empty Status */
-
-/* UART_INT Bitmask */
-#define UART_INT_RIS (1 << 0) /* Rx Interrupt */
-#define UART_INT_TIS (1 << 1) /* Tx Interrupt */
-#define UART_INT_MIS (1 << 2) /* Modem Interrupt */
-#define UART_INT_RTIS (1 << 3) /* Receive Timeout Interrupt */
-
-/* Timer 1 */
-#define TIMER1_BASE __REG(0x80000c00)
-#define TIMER1_LOAD __REG(0x80000c00) /* Timer 1 Load Register */
-#define TIMER1_VAL __REG(0x80000c04) /* Timer 1 Value Register */
-#define TIMER1_CTRL __REG(0x80000c08) /* Timer 1 Control Register */
-#define TIMER1_CLEAR __REG(0x80000c0c) /* Timer 1 Clear Register */
-
-/* Timer 2 */
-#define TIMER2_BASE __REG(0x80000d00)
-#define TIMER2_LOAD __REG(0x80000d00) /* Timer 2 Load Register */
-#define TIMER2_VAL __REG(0x80000d04) /* Timer 2 Value Register */
-#define TIMER2_CTRL __REG(0x80000d08) /* Timer 2 Control Register */
-#define TIMER2_CLEAR __REG(0x80000d0c) /* Timer 2 Clear Register */
-
-/* Timer 3 */
-#define TIMER3_BASE __REG(0x80000e00)
-#define TIMER3_LOAD __REG(0x80000e00) /* Timer 3 Load Register */
-#define TIMER3_VAL __REG(0x80000e04) /* Timer 3 Value Register */
-#define TIMER3_CTRL __REG(0x80000e08) /* Timer 3 Control Register */
-#define TIMER3_CLEAR __REG(0x80000e0c) /* Timer 3 Clear Register */
-
-/* Timer Control register bits */
-#define TIMER_CTRL_ENABLE (1 << 7) /* Enable (Start Timer) */
-#define TIMER_CTRL_PERIODIC (1 << 6) /* Periodic Running Mode */
-#define TIMER_CTRL_FREE_RUNNING (0 << 6) /* Normal Running Mode */
-#define TIMER_CTRL_CLKSEL_508K (1 << 3) /* 508KHz Clock select (Timer 1, 2) */
-#define TIMER_CTRL_CLKSEL_2K (0 << 3) /* 2KHz Clock Select (Timer 1, 2) */
-
-/* Power and State Control */
-#define POWER_BASE __REG(0x80000400)
-#define POWER_PWRSR __REG(0x80000400) /* Power Status Register */
-#define POWER_PWRCNT __REG(0x80000404) /* Power/Clock control */
-#define POWER_HALT __REG(0x80000408) /* Power Idle Mode */
-#define POWER_STDBY __REG(0x8000040c) /* Power Standby Mode */
-#define POWER_BLEOI __REG(0x80000410) /* Battery Low End of Interrupt */
-#define POWER_MCEOI __REG(0x80000414) /* Media Changed EoI */
-#define POWER_TEOI __REG(0x80000418) /* Tick EoI */
-#define POWER_STFCLR __REG(0x8000041c) /* NbFlg, RSTFlg, PFFlg, CLDFlg Clear */
-#define POWER_CLKSET __REG(0x80000420) /* Clock Speed Control */
-
-/* GPIO Registers */
-#define AAEC_GPIO_PHYS 0x80000e00
-
-#define AAEC_GPIO_PADR __REG(AAEC_GPIO_PHYS + 0x00)
-#define AAEC_GPIO_PBDR __REG(AAEC_GPIO_PHYS + 0x04)
-#define AAEC_GPIO_PCDR __REG(AAEC_GPIO_PHYS + 0x08)
-#define AAEC_GPIO_PDDR __REG(AAEC_GPIO_PHYS + 0x0c)
-#define AAEC_GPIO_PADDR __REG(AAEC_GPIO_PHYS + 0x10)
-#define AAEC_GPIO_PBDDR __REG(AAEC_GPIO_PHYS + 0x14)
-#define AAEC_GPIO_PCDDR __REG(AAEC_GPIO_PHYS + 0x18)
-#define AAEC_GPIO_PDDDR __REG(AAEC_GPIO_PHYS + 0x1c)
-#define AAEC_GPIO_PEDR __REG(AAEC_GPIO_PHYS + 0x20)
-#define AAEC_GPIO_PEDDR __REG(AAEC_GPIO_PHYS + 0x24)
-#define AAEC_GPIO_KSCAN __REG(AAEC_GPIO_PHYS + 0x28)
-#define AAEC_GPIO_PINMUX __REG(AAEC_GPIO_PHYS + 0x2c)
-#define AAEC_GPIO_PFDR __REG(AAEC_GPIO_PHYS + 0x30)
-#define AAEC_GPIO_PFDDR __REG(AAEC_GPIO_PHYS + 0x34)
-#define AAEC_GPIO_PGDR __REG(AAEC_GPIO_PHYS + 0x38)
-#define AAEC_GPIO_PGDDR __REG(AAEC_GPIO_PHYS + 0x3c)
-#define AAEC_GPIO_PHDR __REG(AAEC_GPIO_PHYS + 0x40)
-#define AAEC_GPIO_PHDDR __REG(AAEC_GPIO_PHYS + 0x44)
-#define AAEC_GPIO_RAZ __REG(AAEC_GPIO_PHYS + 0x48)
-#define AAEC_GPIO_INTTYPE1 __REG(AAEC_GPIO_PHYS + 0x4c)
-#define AAEC_GPIO_INTTYPE2 __REG(AAEC_GPIO_PHYS + 0x50)
-#define AAEC_GPIO_FEOI __REG(AAEC_GPIO_PHYS + 0x54)
-#define AAEC_GPIO_INTEN __REG(AAEC_GPIO_PHYS + 0x58)
-#define AAEC_GPIO_INTSTATUS __REG(AAEC_GPIO_PHYS + 0x5c)
-#define AAEC_GPIO_RAWINTSTATUS __REG(AAEC_GPIO_PHYS + 0x60)
-#define AAEC_GPIO_DB __REG(AAEC_GPIO_PHYS + 0x64)
-#define AAEC_GPIO_PAPINDR __REG(AAEC_GPIO_PHYS + 0x68)
-#define AAEC_GPIO_PBPINDR __REG(AAEC_GPIO_PHYS + 0x6c)
-#define AAEC_GPIO_PCPINDR __REG(AAEC_GPIO_PHYS + 0x70)
-#define AAEC_GPIO_PDPINDR __REG(AAEC_GPIO_PHYS + 0x74)
-#define AAEC_GPIO_PEPINDR __REG(AAEC_GPIO_PHYS + 0x78)
-#define AAEC_GPIO_PFPINDR __REG(AAEC_GPIO_PHYS + 0x7c)
-#define AAEC_GPIO_PGPINDR __REG(AAEC_GPIO_PHYS + 0x80)
-#define AAEC_GPIO_PHPINDR __REG(AAEC_GPIO_PHYS + 0x84)
-
-#define AAEC_GPIO_PINMUX_PE0CON (1 << 0)
-#define AAEC_GPIO_PINMUX_PD0CON (1 << 1)
-#define AAEC_GPIO_PINMUX_CODECON (1 << 2)
-#define AAEC_GPIO_PINMUX_UART3CON (1 << 3)
-
-/* LCD Controller */
-#define AAEC_CLCD_PHYS 0x80003000
-
-#endif /* __ARM_ARCH_AAEC2000_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/aaed2000.h
- *
- * AAED-2000 specific bits definition
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_AAED2000_H
-#define __ASM_ARCH_AAED2000_H
-
-/* External GPIOs. */
-
-#define EXT_GPIO_PBASE AAEC_CS3
-#define EXT_GPIO_VBASE 0xf8100000
-#define EXT_GPIO_LENGTH 0x00001000
-
-#define __ext_gpio_p2v(x) ((x) - EXT_GPIO_PBASE + EXT_GPIO_VBASE)
-#define __ext_gpio_v2p(x) ((x) + EXT_GPIO_PBASE - EXT_GPIO_VBASE)
-
-#define __EXT_GPIO_REG(x) (*((volatile u32 *)__ext_gpio_p2v(x)))
-#define __EXT_GPIO_PREG(x) (__ext_gpio_v2p((u32)&(x)))
-
-#define AAED_EXT_GPIO __EXT_GPIO_REG(EXT_GPIO_PBASE)
-
-#define AAED_EGPIO_KBD_SCAN 0x00003fff /* Keyboard scan data */
-#define AAED_EGPIO_PWR_INT 0x00008fff /* Smart battery charger interrupt */
-#define AAED_EGPIO_SWITCHED 0x000f0000 /* DIP Switches */
-#define AAED_EGPIO_USB_VBUS 0x00400000 /* USB Vbus sense */
-#define AAED_EGPIO_LCD_PWR_EN 0x02000000 /* LCD and backlight PWR enable */
-#define AAED_EGPIO_nLED0 0x20000000 /* LED 0 */
-#define AAED_EGPIO_nLED1 0x20000000 /* LED 1 */
-#define AAED_EGPIO_nLED2 0x20000000 /* LED 2 */
-
-
-#endif /* __ARM_ARCH_AAED2000_H */
+++ /dev/null
-/* arch/arm/mach-aaec2000/include/mach/debug-macro.S
- *
- * Debugging macro include header
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include "hardware.h"
- .macro addruart, rp, rv
- mov \rp, 0x00000800
- orr \rv, \rp, #io_p2v(0x80000000) @ virtual
- orr \rp, \rp, #0x80000000 @ physical
- .endm
-
- .macro senduart,rd,rx
- str \rd, [\rx, #0]
- .endm
-
- .macro busyuart,rd,rx
-1002: ldr \rd, [\rx, #0x10]
- tst \rd, #(1 << 7)
- beq 1002b
- .endm
-
- .macro waituart,rd,rx
-#if 0
-1001: ldr \rd, [\rx, #0x10]
- tst \rd, #(1 << 5)
- beq 1001b
-#endif
- .endm
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/entry-macro.S
- *
- * Low-level IRQ helper for aaec-2000 based platforms
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- */
-#include <mach/irqs.h>
-
- .macro disable_fiq
- .endm
-
- .macro get_irqnr_preamble, base, tmp
- .endm
-
- .macro arch_ret_to_user, tmp1, tmp2
- .endm
-
- .macro get_irqnr_and_base, irqnr, irqstat, base, tmp
- mov r4, #0xf8000000
- add r4, r4, #0x00000500
- mov \base, r4
- ldr \irqstat, [\base, #0]
- cmp \irqstat, #0
- bne 1001f
- ldr \irqnr, =NR_IRQS+1
- b 1003f
-1001: mov \irqnr, #0
-1002: ands \tmp, \irqstat, #1
- mov \irqstat, \irqstat, LSR #1
- add \irqnr, \irqnr, #1
- beq 1002b
- sub \irqnr, \irqnr, #1
-1003:
- .endm
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/hardware.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <asm/sizes.h>
-#include <mach/aaec2000.h>
-
-/* The kernel is loaded at physical address 0xf8000000.
- * We map the IO space a bit after
- */
-#define PIO_APB_BASE 0x80000000
-#define VIO_APB_BASE 0xf8000000
-#define IO_APB_LENGTH 0x2000
-#define PIO_AHB_BASE 0x80002000
-#define VIO_AHB_BASE 0xf8002000
-#define IO_AHB_LENGTH 0x2000
-
-#define VIO_BASE VIO_APB_BASE
-#define PIO_BASE PIO_APB_BASE
-
-#define io_p2v(x) ( (x) - PIO_BASE + VIO_BASE )
-#define io_v2p(x) ( (x) + PIO_BASE - VIO_BASE )
-
-#ifndef __ASSEMBLY__
-
-#include <asm/types.h>
-
-/* FIXME: Is it needed to optimize this a la pxa ?? */
-#define __REG(x) (*((volatile u32 *)io_p2v(x)))
-#define __PREG(x) (io_v2p((u32)&(x)))
-
-#else /* __ASSEMBLY__ */
-
-#define __REG(x) io_p2v(x)
-#define __PREG(x) io_v2p(x)
-
-#endif
-
-#include "aaec2000.h"
-
-#endif /* __ASM_ARCH_HARDWARE_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/io.h
- *
- * Copied from asm/arch/sa1100/io.h
- */
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * We don't actually have real ISA nor PCI buses, but there is so many
- * drivers out there that might just work if we fake them...
- */
-#define __io(a) __typesafe_io(a)
-#define __mem_pci(a) (a)
-
-#endif
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/irqs.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-
-#define INT_GPIOF0_FIQ 0 /* External GPIO Port F O Fast Interrupt Input */
-#define INT_BL_FIQ 1 /* Battery Low Fast Interrupt */
-#define INT_WE_FIQ 2 /* Watchdog Expired Fast Interrupt */
-#define INT_MV_FIQ 3 /* Media Changed Interrupt */
-#define INT_SC 4 /* Sound Codec Interrupt */
-#define INT_GPIO1 5 /* GPIO Port F Configurable Int 1 */
-#define INT_GPIO2 6 /* GPIO Port F Configurable Int 2 */
-#define INT_GPIO3 7 /* GPIO Port F Configurable Int 3 */
-#define INT_TMR1_OFL 8 /* Timer 1 Overflow Interrupt */
-#define INT_TMR2_OFL 9 /* Timer 2 Overflow Interrupt */
-#define INT_RTC_CM 10 /* RTC Compare Match Interrupt */
-#define INT_TICK 11 /* 64Hz Tick Interrupt */
-#define INT_UART1 12 /* UART1 Interrupt */
-#define INT_UART2 13 /* UART2 & Modem State Changed Interrupt */
-#define INT_LCD 14 /* LCD Interrupt */
-#define INT_SSI 15 /* SSI End of Transfer Interrupt */
-#define INT_UART3 16 /* UART3 Interrupt */
-#define INT_SCI 17 /* SCI Interrupt */
-#define INT_AAC 18 /* Advanced Audio Codec Interrupt */
-#define INT_MMC 19 /* MMC Interrupt */
-#define INT_USB 20 /* USB Interrupt */
-#define INT_DMA 21 /* DMA Interrupt */
-#define INT_TMR3_UOFL 22 /* Timer 3 Underflow Interrupt */
-#define INT_GPIO4 23 /* GPIO Port F Configurable Int 4 */
-#define INT_GPIO5 24 /* GPIO Port F Configurable Int 4 */
-#define INT_GPIO6 25 /* GPIO Port F Configurable Int 4 */
-#define INT_GPIO7 26 /* GPIO Port F Configurable Int 4 */
-#define INT_BMI 27 /* BMI Interrupt */
-
-#define NR_IRQS (INT_BMI + 1)
-
-#endif /* __ASM_ARCH_IRQS_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/memory.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-
-#define PHYS_OFFSET UL(0xf0000000)
-
-#endif /* __ASM_ARCH_MEMORY_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaed2000/include/mach/system.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_SYSTEM_H
-#define __ASM_ARCH_SYSTEM_H
-
-static inline void arch_idle(void)
-{
- cpu_do_idle();
-}
-
-static inline void arch_reset(char mode, const char *cmd)
-{
- cpu_reset(0);
-}
-
-#endif /* __ASM_ARCH_SYSTEM_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/timex.h
- *
- * AAEC-2000 Architecture timex specification
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_TIMEX_H
-#define __ASM_ARCH_TIMEX_H
-
-#define CLOCK_TICK_RATE 508000
-
-#endif /* __ASM_ARCH_TIMEX_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/uncompress.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_UNCOMPRESS_H
-#define __ASM_ARCH_UNCOMPRESS_H
-
-#include "hardware.h"
-
-#define UART(x) (*(volatile unsigned long *)(serial_port + (x)))
-
-static void putc(int c)
-{
- unsigned long serial_port;
- do {
- serial_port = _UART3_BASE;
- if (UART(UART_CR) & UART_CR_EN) break;
- serial_port = _UART1_BASE;
- if (UART(UART_CR) & UART_CR_EN) break;
- serial_port = _UART2_BASE;
- if (UART(UART_CR) & UART_CR_EN) break;
- return;
- } while (0);
-
- /* wait for space in the UART's transmitter */
- while ((UART(UART_SR) & UART_SR_TxFF))
- barrier();
-
- /* send the character out. */
- UART(UART_DR) = c;
-}
-
-static inline void flush(void)
-{
-}
-
-#define arch_decomp_setup()
-#define arch_decomp_wdog()
-
-#endif /* __ASM_ARCH_UNCOMPRESS_H */
+++ /dev/null
-/*
- * arch/arm/mach-aaec2000/include/mach/vmalloc.h
- *
- * Copyright (c) 2005 Nicolas Bellido Y Ortega
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#ifndef __ASM_ARCH_VMALLOC_H
-#define __ASM_ARCH_VMALLOC_H
-
-#define VMALLOC_END 0xd0000000UL
-
-#endif /* __ASM_ARCH_VMALLOC_H */
git.openpandora.org / pandora-kernel.git / commitdiff