#ifndef __iwl_3945_hw__
#define __iwl_3945_hw__
-/* uCode queue management definitions */
+/*
+ * uCode queue management definitions ...
+ * Queue #4 is the command queue for 3945 and 4965.
+ */
#define IWL_CMD_QUEUE_NUM 4
-#define IWL_CMD_FIFO_NUM 4
-#define IWL_BACK_QUEUE_FIRST_ID 7
/* Tx rates */
#define IWL_CCK_RATES 4
u8 reserved9[194];
-
/*
* 3945 Txpower calibration data.
*/
#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
#define CSR_GP_CNTRL (CSR_BASE+0x024)
+
+/*
+ * Hardware revision info
+ * Bit fields:
+ * 31-8: Reserved
+ * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
+ * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
+ * 1-0: "Dash" value, as in A-1, etc.
+ */
#define CSR_HW_REV (CSR_BASE+0x028)
+
+/* EEPROM reads */
#define CSR_EEPROM_REG (CSR_BASE+0x02c)
#define CSR_EEPROM_GP (CSR_BASE+0x030)
#define CSR_GP_UCODE (CSR_BASE+0x044)
#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_LED_REG (CSR_BASE+0x094)
-#define CSR_DRAM_INT_TBL_CTL (CSR_BASE+0x0A0)
#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
+
+/* Analog phase-lock-loop configuration (3945 only)
+ * Set bit 24. */
#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
-#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
-/* HW I/F configuration */
+/* Bits for CSR_HW_IF_CONFIG_REG */
#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB (0x00000100)
#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM (0x00000200)
#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400)
/* CSR_ANA_PLL_CFG */
#define CSR_ANA_PLL_CFG_SH (0x00880300)
-#define CSR_LED_REG_TRUN_ON (0x00000078)
-#define CSR_LED_REG_TRUN_OFF (0x00000038)
-#define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF)
-
-/* DRAM_INT_TBL_CTRL */
-#define CSR_DRAM_INT_TBL_CTRL_EN (1<<31)
-#define CSR_DRAM_INT_TBL_CTRL_WRAP_CHK (1<<27)
-
/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE (0x400)
+/*
+ * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
+ * structures, error log, event log, verifying uCode load).
+ * First write to address register, then read from or write to data register
+ * to complete the job. Once the address register is set up, accesses to
+ * data registers auto-increment the address by one dword.
+ * Bit usage for address registers (read or write):
+ * 0-31: memory address within device
+ */
#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
+
+/*
+ * Registers for accessing device's internal peripheral registers
+ * (e.g. SCD, BSM, etc.). First write to address register,
+ * then read from or write to data register to complete the job.
+ * Bit usage for address registers (read or write):
+ * 0-15: register address (offset) within device
+ * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
+ */
#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
-#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
-
-#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
+/*
+ * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
+ * Indicates index to next TFD that driver will fill (1 past latest filled).
+ * Bit usage:
+ * 0-7: queue write index
+ * 11-8: queue selector
+ */
+#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
-/* SCD (Scheduler) */
+/* SCD (3945 Tx Frame Scheduler) */
#define SCD_BASE (CSR_BASE + 0x2E00)
#define SCD_MODE_REG (SCD_BASE + 0x000)
#ifndef __iwl_4965_hw_h__
#define __iwl_4965_hw_h__
-/* uCode queue management definitions */
+/*
+ * uCode queue management definitions ...
+ * Queue #4 is the command queue for 3945 and 4965; map it to Tx FIFO chnl 4.
+ * The first queue used for block-ack aggregation is #7 (4965 only).
+ * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
+ */
#define IWL_CMD_QUEUE_NUM 4
#define IWL_CMD_FIFO_NUM 4
#define IWL_BACK_QUEUE_FIRST_ID 7
#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */
#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/
#define CSR_GP_CNTRL (CSR_BASE+0x024)
+
+/*
+ * Hardware revision info
+ * Bit fields:
+ * 31-8: Reserved
+ * 7-4: Type of device: 0x0 = 4965, 0xd = 3945
+ * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D
+ * 1-0: "Dash" value, as in A-1, etc.
+ *
+ * NOTE: Revision step affects calculation of CCK txpower for 4965.
+ */
#define CSR_HW_REV (CSR_BASE+0x028)
+
+/* EEPROM reads */
#define CSR_EEPROM_REG (CSR_BASE+0x02c)
#define CSR_EEPROM_GP (CSR_BASE+0x030)
#define CSR_GP_UCODE (CSR_BASE+0x044)
#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058)
#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c)
#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060)
-#define CSR_LED_REG (CSR_BASE+0x094)
-#define CSR_DRAM_INT_TBL_CTL (CSR_BASE+0x0A0)
#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100)
-#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c)
+
+/*
+ * Indicates hardware rev, to determine CCK backoff for txpower calculation.
+ * Bit fields:
+ * 3-2: 0 = A, 1 = B, 2 = C, 3 = D step
+ */
#define CSR_HW_REV_WA_REG (CSR_BASE+0x22C)
/* HW I/F configuration */
#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000)
#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000)
-/* CSR_ANA_PLL_CFG */
-#define CSR_ANA_PLL_CFG_SH (0x00880300)
-
-#define CSR_LED_REG_TRUN_ON (0x00000078)
-#define CSR_LED_REG_TRUN_OFF (0x00000038)
-#define CSR_LED_BSM_CTRL_MSK (0xFFFFFFDF)
-
-/* DRAM_INT_TBL_CTRL */
-#define CSR_DRAM_INT_TBL_CTRL_EN (1<<31)
-#define CSR_DRAM_INT_TBL_CTRL_WRAP_CHK (1<<27)
-
/*=== HBUS (Host-side Bus) ===*/
#define HBUS_BASE (0x400)
+/*
+ * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM
+ * structures, error log, event log, verifying uCode load).
+ * First write to address register, then read from or write to data register
+ * to complete the job. Once the address register is set up, accesses to
+ * data registers auto-increment the address by one dword.
+ * Bit usage for address registers (read or write):
+ * 0-31: memory address within device
+ */
#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c)
#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010)
#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018)
#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c)
+
+/*
+ * Registers for accessing device's internal peripheral registers
+ * (e.g. SCD, BSM, etc.). First write to address register,
+ * then read from or write to data register to complete the job.
+ * Bit usage for address registers (read or write):
+ * 0-15: register address (offset) within device
+ * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword)
+ */
#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044)
#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048)
#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c)
#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050)
+
+/*
+ * Per-Tx-queue write pointer (index, really!) (3945 and 4965).
+ * Indicates index to next TFD that driver will fill (1 past latest filled).
+ * Bit usage:
+ * 0-7: queue write index (0-255)
+ * 11-8: queue selector (0-15)
+ */
#define HBUS_TARG_WRPTR (HBUS_BASE+0x060)
#define HBUS_TARG_MBX_C (HBUS_BASE+0x030)
-
-/* SCD (Scheduler) */
-#define SCD_BASE (CSR_BASE + 0x2E00)
-
-#define SCD_MODE_REG (SCD_BASE + 0x000)
-#define SCD_ARASTAT_REG (SCD_BASE + 0x004)
-#define SCD_TXFACT_REG (SCD_BASE + 0x010)
-#define SCD_TXF4MF_REG (SCD_BASE + 0x014)
-#define SCD_TXF5MF_REG (SCD_BASE + 0x020)
-#define SCD_SBYP_MODE_1_REG (SCD_BASE + 0x02C)
-#define SCD_SBYP_MODE_2_REG (SCD_BASE + 0x030)
-
/*=== FH (data Flow Handler) ===*/
#define FH_BASE (0x800)
git.openpandora.org / pandora-kernel.git / commitdiff