return bnx2x_nic_load(bp, LOAD_NORMAL);
}
+int bnx2x_get_cur_phy_idx(struct bnx2x *bp)
+{
+ u32 sel_phy_idx = 0;
+ if (bp->link_params.num_phys <= 1)
+ return INT_PHY;
+
+ if (bp->link_vars.link_up) {
+ sel_phy_idx = EXT_PHY1;
+ /* In case link is SERDES, check if the EXT_PHY2 is the one */
+ if ((bp->link_vars.link_status & LINK_STATUS_SERDES_LINK) &&
+ (bp->link_params.phy[EXT_PHY2].supported & SUPPORTED_FIBRE))
+ sel_phy_idx = EXT_PHY2;
+ } else {
+
+ switch (bnx2x_phy_selection(&bp->link_params)) {
+ case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT:
+ case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY:
+ case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
+ sel_phy_idx = EXT_PHY1;
+ break;
+ case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY:
+ case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
+ sel_phy_idx = EXT_PHY2;
+ break;
+ }
+ }
+
+ return sel_phy_idx;
+
+}
+int bnx2x_get_link_cfg_idx(struct bnx2x *bp)
+{
+ u32 sel_phy_idx = bnx2x_get_cur_phy_idx(bp);
+ /*
+ * The selected actived PHY is always after swapping (in case PHY
+ * swapping is enabled). So when swapping is enabled, we need to reverse
+ * the configuration
+ */
+
+ if (bp->link_params.multi_phy_config &
+ PORT_HW_CFG_PHY_SWAPPED_ENABLED) {
+ if (sel_phy_idx == EXT_PHY1)
+ sel_phy_idx = EXT_PHY2;
+ else if (sel_phy_idx == EXT_PHY2)
+ sel_phy_idx = EXT_PHY1;
+ }
+ return LINK_CONFIG_IDX(sel_phy_idx);
+}
+
/* called with rtnl_lock */
int bnx2x_change_mtu(struct net_device *dev, int new_mtu)
{
struct bnx2x *bp = params->bp;
u8 link_10g;
u8 port = params->port;
-
+ u32 sync_offset, media_types;
vars->link_status = REG_RD(bp, params->shmem_base +
offsetof(struct shmem_region,
port_mb[port].link_status));
vars->mac_type = MAC_TYPE_NONE;
}
+ /* Sync media type */
+ sync_offset = params->shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[port].media_type);
+ media_types = REG_RD(bp, sync_offset);
+
+ params->phy[INT_PHY].media_type =
+ (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) >>
+ PORT_HW_CFG_MEDIA_TYPE_PHY0_SHIFT;
+ params->phy[EXT_PHY1].media_type =
+ (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY1_MASK) >>
+ PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT;
+ params->phy[EXT_PHY2].media_type =
+ (media_types & PORT_HW_CFG_MEDIA_TYPE_PHY2_MASK) >>
+ PORT_HW_CFG_MEDIA_TYPE_PHY2_SHIFT;
+ DP(NETIF_MSG_LINK, "media_types = 0x%x\n", media_types);
+
DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x\n",
vars->link_status, vars->phy_link_up);
DP(NETIF_MSG_LINK, "line_speed %x duplex %x flow_ctrl 0x%x\n",
serdes_phy_type = ((params->phy[phy_index].media_type ==
ETH_PHY_SFP_FIBER) ||
(params->phy[phy_index].media_type ==
- ETH_PHY_XFP_FIBER));
+ ETH_PHY_XFP_FIBER) ||
+ (params->phy[phy_index].media_type ==
+ ETH_PHY_DA_TWINAX));
if (is_serdes != serdes_phy_type)
continue;
u16 *edc_mode)
{
struct bnx2x *bp = params->bp;
+ u32 sync_offset = 0, phy_idx, media_types;
u8 val, check_limiting_mode = 0;
*edc_mode = EDC_MODE_LIMITING;
+ phy->media_type = ETH_PHY_UNSPECIFIED;
/* First check for copper cable */
if (bnx2x_read_sfp_module_eeprom(phy,
params,
case SFP_EEPROM_CON_TYPE_VAL_COPPER:
{
u8 copper_module_type;
-
+ phy->media_type = ETH_PHY_DA_TWINAX;
/*
* Check if its active cable (includes SFP+ module)
* of passive cable
break;
}
case SFP_EEPROM_CON_TYPE_VAL_LC:
+ phy->media_type = ETH_PHY_SFP_FIBER;
DP(NETIF_MSG_LINK, "Optic module detected\n");
check_limiting_mode = 1;
break;
val);
return -EINVAL;
}
-
+ sync_offset = params->shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[params->port].media_type);
+ media_types = REG_RD(bp, sync_offset);
+ /* Update media type for non-PMF sync */
+ for (phy_idx = INT_PHY; phy_idx < MAX_PHYS; phy_idx++) {
+ if (&(params->phy[phy_idx]) == phy) {
+ media_types &= ~(PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK <<
+ (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx));
+ media_types |= ((phy->media_type &
+ PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) <<
+ (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT * phy_idx));
+ break;
+ }
+ }
+ REG_WR(bp, sync_offset, media_types);
if (check_limiting_mode) {
u8 options[SFP_EEPROM_OPTIONS_SIZE];
if (bnx2x_read_sfp_module_eeprom(phy,
* Module was plugged out.
* Disable transmit for this module
*/
+ phy->media_type = ETH_PHY_NOT_PRESENT;
if ((val & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK) ==
PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER)
bnx2x_sfp_set_transmitter(params, phy, 0);
/* Module is absent */
DP(NETIF_MSG_LINK, "MOD_ABS indication "
"show module is absent\n");
-
+ phy->media_type = ETH_PHY_NOT_PRESENT;
/*
* 1. Set mod_abs to detect next module
* presence event
SUPPORTED_Autoneg |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
- .media_type = ETH_PHY_UNSPECIFIED,
+ .media_type = ETH_PHY_BASE_T,
.ver_addr = 0,
.req_flow_ctrl = 0,
.req_line_speed = 0,
SUPPORTED_Autoneg |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
- .media_type = ETH_PHY_UNSPECIFIED,
+ .media_type = ETH_PHY_CX4,
.ver_addr = 0,
.req_flow_ctrl = 0,
.req_line_speed = 0,
SUPPORTED_Autoneg |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
- .media_type = ETH_PHY_UNSPECIFIED,
+ .media_type = ETH_PHY_KR,
.ver_addr = 0,
.req_flow_ctrl = 0,
.req_line_speed = 0,
SUPPORTED_FIBRE |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
- .media_type = ETH_PHY_SFP_FIBER,
+ .media_type = ETH_PHY_NOT_PRESENT,
.ver_addr = 0,
.req_flow_ctrl = 0,
.req_line_speed = 0,
SUPPORTED_FIBRE |
SUPPORTED_Pause |
SUPPORTED_Asym_Pause),
- .media_type = ETH_PHY_SFP_FIBER,
+ .media_type = ETH_PHY_NOT_PRESENT,
.ver_addr = 0,
.req_flow_ctrl = 0,
.req_line_speed = 0,
u8 bnx2x_phy_probe(struct link_params *params)
{
u8 phy_index, actual_phy_idx, link_cfg_idx;
- u32 phy_config_swapped;
+ u32 phy_config_swapped, sync_offset, media_types;
struct bnx2x *bp = params->bp;
struct bnx2x_phy *phy;
params->num_phys = 0;
if (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN)
break;
+ sync_offset = params->shmem_base +
+ offsetof(struct shmem_region,
+ dev_info.port_hw_config[params->port].media_type);
+ media_types = REG_RD(bp, sync_offset);
+
+ /*
+ * Update media type for non-PMF sync only for the first time
+ * In case the media type changes afterwards, it will be updated
+ * using the update_status function
+ */
+ if ((media_types & (PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK <<
+ (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT *
+ actual_phy_idx))) == 0) {
+ media_types |= ((phy->media_type &
+ PORT_HW_CFG_MEDIA_TYPE_PHY0_MASK) <<
+ (PORT_HW_CFG_MEDIA_TYPE_PHY1_SHIFT *
+ actual_phy_idx));
+ }
+ REG_WR(bp, sync_offset, media_types);
+
bnx2x_phy_def_cfg(params, phy, phy_index);
params->num_phys++;
}
return 0;
}
-int bnx2x_get_link_cfg_idx(struct bnx2x *bp)
-{
- u32 sel_phy_idx = 0;
- if (bp->link_vars.link_up) {
- sel_phy_idx = EXT_PHY1;
- /* In case link is SERDES, check if the EXT_PHY2 is the one */
- if ((bp->link_vars.link_status & LINK_STATUS_SERDES_LINK) &&
- (bp->link_params.phy[EXT_PHY2].supported & SUPPORTED_FIBRE))
- sel_phy_idx = EXT_PHY2;
- } else {
-
- switch (bnx2x_phy_selection(&bp->link_params)) {
- case PORT_HW_CFG_PHY_SELECTION_HARDWARE_DEFAULT:
- case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY:
- case PORT_HW_CFG_PHY_SELECTION_FIRST_PHY_PRIORITY:
- sel_phy_idx = EXT_PHY1;
- break;
- case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY:
- case PORT_HW_CFG_PHY_SELECTION_SECOND_PHY_PRIORITY:
- sel_phy_idx = EXT_PHY2;
- break;
- }
- }
- /*
- * The selected actived PHY is always after swapping (in case PHY
- * swapping is enabled). So when swapping is enabled, we need to reverse
- * the configuration
- */
-
- if (bp->link_params.multi_phy_config &
- PORT_HW_CFG_PHY_SWAPPED_ENABLED) {
- if (sel_phy_idx == EXT_PHY1)
- sel_phy_idx = EXT_PHY2;
- else if (sel_phy_idx == EXT_PHY2)
- sel_phy_idx = EXT_PHY1;
- }
- return LINK_CONFIG_IDX(sel_phy_idx);
-}
-
void bnx2x_calc_fc_adv(struct bnx2x *bp)
{
u8 cfg_idx = bnx2x_get_link_cfg_idx(bp);
git.openpandora.org / pandora-kernel.git / commitdiff