1 source "drivers/net/phy/Kconfig"
2 source "drivers/net/pfe_eth/Kconfig"
3 source "drivers/net/fsl-mc/Kconfig"
6 bool "Enable Driver Model for Ethernet drivers"
9 Enable driver model for Ethernet.
11 The eth_*() interface will be implemented by the UCLASS_ETH class
12 This is currently implemented in net/eth-uclass.c
13 Look in include/net.h for details.
16 bool "Enable Driver Model for MDIO devices"
17 depends on DM_ETH && PHYLIB
19 Enable driver model for MDIO devices
21 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
22 stand-alone devices. Useful in particular for systems that support
23 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
25 This is currently implemented in net/mdio-uclass.c
26 Look in include/miiphy.h for details.
29 bool "Enable Driver Model for MDIO MUX devices"
32 Enable driver model for MDIO MUX devices
34 Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for
35 systems that support DM_MDIO and integrate one or multiple muxes on
37 This is currently implemented in net/mdio-mux-uclass.c
38 Look in include/miiphy.h for details.
41 bool "Enable Driver Model for DSA switches"
42 depends on DM_ETH && DM_MDIO
45 Enable driver model for DSA switches
47 Adds UCLASS_DSA class supporting switches that follow the Distributed
48 Switch Architecture (DSA). These switches rely on the presence of a
49 management switch port connected to an Ethernet controller capable of
50 receiving frames from the switch. This host Ethernet controller is
51 called the "master" Ethernet interface in DSA terminology.
52 This is currently implemented in net/dsa-uclass.c, refer to
53 include/net/dsa.h for API details.
56 depends on DM_MDIO && SANDBOX
58 bool "Sandbox: Mocked MDIO driver"
60 This driver implements dummy read/write/reset MDIO functions mimicking
61 a bus with a single PHY.
63 This driver is used in for testing in test/dm/mdio.c
65 config MDIO_MUX_SANDBOX
66 depends on DM_MDIO_MUX && MDIO_SANDBOX
68 bool "Sandbox: Mocked MDIO-MUX driver"
70 This driver implements dummy select/deselect ops mimicking a MUX on
71 the MDIO bux. It uses mdio_sandbox driver as parent MDIO.
73 This driver is used for testing in test/dm/mdio.c
76 bool "Enable Driver Model for Ethernet Generic PHY drivers"
79 Enable driver model for Ethernet Generic PHY .
82 bool "Network device support"
86 You must select Y to enable any network device support
87 Generally if you have any networking support this is a given
94 bool "Enable GbE PHY status parsing and configuration"
96 Enables support for parsing the status output and for
97 configuring GbE PHYs (affects the inner workings of some
98 commands and miiphyutil.c).
101 bool "Atheros AG7xxx Ethernet MAC support"
102 depends on DM_ETH && ARCH_ATH79
105 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
106 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
110 bool "Altera Triple-Speed Ethernet MAC support"
114 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
115 Please find details on the "Triple-Speed Ethernet MegaCore Function
116 Resource Center" of Altera.
119 bool "Broadcom SF2 (Starfighter2) Ethernet support"
122 This is an abstract framework which provides a generic interface
123 to MAC and DMA management for multiple Broadcom SoCs such as
124 Cygnus, NSP and bcm28155_ap platforms.
126 config BCM_SF2_ETH_DEFAULT_PORT
127 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
128 depends on BCM_SF2_ETH
131 Default port number for the Starfighter2 ethernet driver.
133 config BCM_SF2_ETH_GMAC
134 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
135 depends on BCM_SF2_ETH
137 This flag enables the ethernet support for Broadcom platforms with
138 GMAC such as Cygnus. This driver is based on the framework provided
139 by the BCM_SF2_ETH driver.
140 Say Y to any bcmcygnus based platforms.
143 bool "BCM6348 EMAC support"
144 depends on DM_ETH && ARCH_BMIPS
150 This driver supports the BCM6348 Ethernet MAC.
153 bool "BCM6368 EMAC support"
154 depends on DM_ETH && ARCH_BMIPS
158 This driver supports the BCM6368 Ethernet MAC.
161 bool "BCMGENET V5 support"
165 This driver supports the BCMGENET Ethernet MAC.
167 config CORTINA_NI_ENET
168 bool "Cortina-Access Ethernet driver"
169 depends on DM_ETH && CORTINA_PLATFORM
171 This driver supports the Cortina-Access Ethernet MAC for
172 all supported CAxxxx SoCs.
175 bool "Synopsys DWC Ethernet QOS device support"
179 This driver supports the Synopsys Designware Ethernet QOS (Quality
180 Of Service) IP block. The IP supports many options for bus type,
181 clocking/reset structure, and feature list.
183 config DWC_ETH_QOS_IMX
184 bool "Synopsys DWC Ethernet QOS device support for IMX"
185 depends on DWC_ETH_QOS
187 The Synopsys Designware Ethernet QOS IP block with the specific
188 configuration used in IMX soc.
190 config DWC_ETH_QOS_STM32
191 bool "Synopsys DWC Ethernet QOS device support for STM32"
192 depends on DWC_ETH_QOS
193 default y if ARCH_STM32MP
195 The Synopsys Designware Ethernet QOS IP block with the specific
196 configuration used in STM32MP soc.
198 config DWC_ETH_QOS_TEGRA186
199 bool "Synopsys DWC Ethernet QOS device support for TEGRA186"
200 depends on DWC_ETH_QOS
201 default y if TEGRA186
203 The Synopsys Designware Ethernet QOS IP block with specific
204 configuration used in NVIDIA's Tegra186 chip.
207 bool "Intel PRO/1000 Gigabit Ethernet support"
208 depends on (DM_ETH && DM_PCI) || !DM_ETH
210 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
211 adapters. For more information on how to identify your adapter, go
212 to the Adapter & Driver ID Guide at:
214 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
216 config E1000_SPI_GENERIC
217 bool "Allow access to the Intel 8257x SPI bus"
220 Allow generic access to the SPI bus on the Intel 8257x, for
221 example with the "sspi" command.
224 bool "Enable SPI bus utility code"
227 Utility code for direct access to the SPI bus on Intel 8257x.
228 This does not do anything useful unless you set at least one
229 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
232 bool "Enable the e1000 command"
235 This enables the 'e1000' management command for E1000 devices. When
236 used on devices with SPI support you can reprogram the EEPROM from
240 bool "Intel PRO/100 82557/82559/82559ER Fast Ethernet support"
242 This driver supports Intel(R) PRO/100 82557/82559/82559ER fast
243 ethernet family of adapters.
246 depends on DM_ETH && SANDBOX
248 bool "Sandbox: Mocked Ethernet driver"
250 This driver simply responds with fake ARP replies and ping
251 replies that are used to verify network stack functionality
253 This driver is particularly useful in the test/dm/eth.c tests
255 config ETH_SANDBOX_RAW
256 depends on DM_ETH && SANDBOX
258 bool "Sandbox: Bridge to Linux Raw Sockets"
260 This driver is a bridge from the bottom of the network stack
261 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
262 network traffic to be tested from within sandbox. See
263 doc/arch/index.rst for more details.
265 config ETH_DESIGNWARE
266 bool "Synopsys Designware Ethernet MAC"
268 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
270 This MAC is present in SoCs from various vendors. It supports
271 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
272 provide the PHY (physical media interface).
274 config ETH_DESIGNWARE_MESON8B
275 bool "Amlogic Meson8b and later glue driver for Synopsys Designware Ethernet MAC"
277 select ETH_DESIGNWARE
279 This provides glue layer to use Synopsys Designware Ethernet MAC
280 present on the Amlogic Meson8b, GX, AXG & G12A SoCs.
282 config ETH_DESIGNWARE_SOCFPGA
285 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
286 depends on DM_ETH && ETH_DESIGNWARE
288 The Altera SoCFPGA requires additional configuration of the
289 Altera system manager to correctly interface with the PHY.
290 This code handles those SoC specifics.
292 config ETH_DESIGNWARE_S700
293 bool "Actins S700 glue driver for Synopsys Designware Ethernet MAC"
294 depends on DM_ETH && ETH_DESIGNWARE
296 This provides glue layer to use Synopsys Designware Ethernet MAC
297 present on Actions S700 SoC.
300 bool "OpenCores 10/100 Mbps Ethernet MAC"
302 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
304 config FEC_MXC_SHARE_MDIO
305 bool "Share the MDIO bus for FEC controller"
308 config FEC_MXC_MDIO_BASE
309 hex "MDIO base address for the FEC controller"
310 depends on FEC_MXC_SHARE_MDIO
312 This specifies the MDIO registers base address. It is used when
313 two FEC controllers share MDIO bus.
316 bool "FEC Ethernet controller"
317 depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610
319 This driver supports the 10/100 Fast Ethernet controller for
323 bool "Freescale FMan ethernet support"
324 depends on ARM || PPC
326 This driver support the Freescale FMan Ethernet controller
329 bool "Ftmac100 Ethernet Support"
331 This MAC is present in Andestech SoCs.
334 bool "Ftgmac100 Ethernet Support"
338 This driver supports the Faraday's FTGMAC100 Gigabit SoC
339 Ethernet controller that can be found on Aspeed SoCs (which
342 It is fully compliant with IEEE 802.3 specification for
343 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
344 Mbps Ethernet and includes Reduced Media Independent
345 Interface (RMII) and Reduced Gigabit Media Independent
346 Interface (RGMII) interfaces. It adopts an AHB bus interface
347 and integrates a link list DMA engine with direct M-Bus
348 accesses for transmitting and receiving packets. It has
349 independent TX/RX fifos, supports half and full duplex (1000
350 Mbps mode only supports full duplex), flow control for full
351 duplex and backpressure for half duplex.
353 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
354 and supports IEEE 802.1Q VLAN tag insertion and removal. It
355 offers high-priority transmit queue for QoS and CoS
360 bool "ColdFire Ethernet Support"
364 This driver supports the network interface units in the
368 bool "ColdFire DMA Ethernet Support"
372 This driver supports the network interface units in the
376 bool "Microchip KS8851-MLL controller driver"
378 The Microchip KS8851 parallel bus external ethernet interface chip.
382 config KS8851_MLL_BASEADDR
383 hex "Microchip KS8851-MLL Base Address"
385 Define this to hold the physical address of the device (I/O space)
390 bool "Marvell Orion5x/Kirkwood network interface support"
391 depends on ARCH_KIRKWOOD || ARCH_ORION5X
392 select PHYLIB if DM_ETH
394 This driver supports the network interface units in the
395 Marvell Orion5x and Kirkwood SoCs
398 bool "Marvell Armada XP/385/3700 network interface support"
399 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
402 This driver supports the network interface units in the
403 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
406 bool "Marvell Armada 375/7K/8K network interface support"
407 depends on ARMADA_375 || ARMADA_8K
412 This driver supports the network interface units in the
413 Marvell ARMADA 375, 7K and 8K SoCs.
416 bool "Cadence MACB/GEM Ethernet Interface"
420 The Cadence MACB ethernet interface is found on many Atmel
421 AT91 and SAMA5 parts. This driver also supports the Cadence
422 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
423 Say Y to include support for the MACB/GEM chip.
426 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
429 The Cadence MACB ethernet interface was used on Zynq platform.
430 Say Y to enable support for the MACB/GEM in Zynq chip.
433 bool "MediaTek MT7620 Ethernet Interface"
434 depends on SOC_MT7620
440 The MediaTek MT7620 ethernet interface is used on MT7620 based
441 boards. It has a built-in switch with two configurable ports which
442 can connect to external PHY/MACs.
445 bool "MediaTek MT7628 Ethernet Interface"
446 depends on SOC_MT7628
449 The MediaTek MT7628 ethernet interface is used on MT7628 and
453 bool "OcteonTX Ethernet support"
454 depends on ARCH_OCTEONTX
457 You must select Y to enable network device support for
458 OcteonTX SoCs. If unsure, say n
461 bool "OcteonTX2 Ethernet support"
462 depends on ARCH_OCTEONTX2
463 select OCTEONTX2_CGX_INTF
465 You must select Y to enable network device support for
466 OcteonTX2 SoCs. If unsure, say n
469 bool "OcteonTX SMI Device support"
470 depends on ARCH_OCTEONTX || ARCH_OCTEONTX2
472 You must select Y to enable SMI controller support for
473 OcteonTX or OcteonTX2 SoCs. If unsure, say n
475 config OCTEONTX2_CGX_INTF
476 bool "OcteonTX2 CGX ATF interface support"
477 depends on ARCH_OCTEONTX2
478 default y if ARCH_OCTEONTX2
480 You must select Y to enable CGX ATF interface support for
481 OcteonTX2 SoCs. If unsure, say n
484 bool "Intel Platform Controller Hub EG20T GMAC driver"
485 depends on DM_ETH && DM_PCI
488 This MAC is present in Intel Platform Controller Hub EG20T. It
489 supports 10/100/1000 Mbps operation.
494 Enable the support of the Reduced Gigabit Media-Independent
500 Enable support of the Media-Independent Interface (MII)
503 bool "AMD PCnet series Ethernet controller driver"
505 This driver supports AMD PCnet series fast ethernet family of
506 PCI chipsets/adapters.
508 source "drivers/net/qe/Kconfig"
511 bool "Realtek 8139 series Ethernet controller driver"
513 This driver supports Realtek 8139 series fast ethernet family of
514 PCI chipsets/adapters.
517 bool "Realtek 8169 series Ethernet controller driver"
519 This driver supports Realtek 8169 series gigabit ethernet family of
520 PCI/PCIe chipsets/adapters.
523 bool "SMSC LAN911x and LAN921x controller driver"
529 hex "SMC911X Base Address"
531 Define this to hold the physical address
532 of the device (I/O space)
536 prompt "SMC911X bus width"
537 default SMC911X_16_BIT
539 config SMC911X_32_BIT
540 bool "Enable 32-bit interface"
542 config SMC911X_16_BIT
543 bool "Enable 16-bit interface"
545 Define this if data bus is 16 bits. If your processor
546 automatically converts one 32 bit word to two 16 bit
547 words you may also try CONFIG_SMC911X_32_BIT.
553 bool "Enable Allwinner GMAC Ethernet support"
555 Enable the support for Sun7i GMAC Ethernet controller
557 config SUN7I_GMAC_FORCE_TXERR
558 bool "Force PA17 as gmac function"
559 depends on SUN7I_GMAC
561 Some ethernet phys needs TXERR control. Since the GMAC
562 doesn't have such signal, setting PA17 as GMAC function
563 makes the pin output low, which enables data transmission.
566 bool "Allwinner Sun4i Ethernet MAC support"
570 This driver supports the Allwinner based SUN4I Ethernet MAC.
573 bool "Allwinner Sun8i Ethernet MAC support"
578 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
579 It can be found in H3/A64/A83T based SoCs and compatible with both
580 External and Internal PHYs.
583 bool "Renesas SH Ethernet MAC"
586 This driver supports the Ethernet for Renesas SH and ARM SoCs.
588 source "drivers/net/ti/Kconfig"
591 bool "DEC Tulip DC2114x Ethernet support"
592 depends on (DM_ETH && DM_PCI) || !DM_ETH
594 This driver supports DEC DC2114x Fast ethernet chips.
596 config XILINX_AXIEMAC
600 bool "Xilinx AXI Ethernet"
602 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
604 config XILINX_EMACLITE
608 bool "Xilinx Ethernetlite"
610 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
615 bool "Xilinx Ethernet GEM"
617 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
620 bool "Microchip PIC32 Ethernet Support"
621 depends on DM_ETH && MACH_PIC32
624 This driver implements 10/100 Mbps Ethernet and MAC layer for
625 Microchip PIC32 microcontrollers.
628 bool "Rockchip Synopsys Designware Ethernet MAC"
629 depends on DM_ETH && ETH_DESIGNWARE
631 This driver provides Rockchip SoCs network support based on the
632 Synopsys Designware driver.
635 bool "Renesas Ethernet AVB MAC"
636 depends on DM_ETH && RCAR_GEN3
639 This driver implements support for the Ethernet AVB block in
640 Renesas M3 and H3 SoCs.
643 bool "Fast Ethernet Controller on MPC8XX"
647 This driver implements support for the Fast Ethernet Controller
651 bool "Socionext AVE Ethernet support"
652 depends on DM_ETH && ARCH_UNIPHIER
657 This driver implements support for the Socionext AVE Ethernet
658 controller, as found on the Socionext UniPhier family.
660 source "drivers/net/mscc_eswitch/Kconfig"
664 depends on MPC8XX_FEC
669 depends on ETHER_ON_FEC1
672 Define to the hardcoded PHY address which corresponds
673 to the given FEC; i. e.
674 #define CONFIG_FEC1_PHY 4
675 means that the PHY with address 4 is connected to FEC1
677 When set to -1, means to probe for first available.
681 depends on ETHER_ON_FEC1
684 The PHY does not have a RXERR line (RMII only).
685 (so program the FEC to ignore it).
689 depends on MPC8XX_FEC && MPC885
694 depends on ETHER_ON_FEC2
697 Define to the hardcoded PHY address which corresponds
698 to the given FEC; i. e.
699 #define CONFIG_FEC1_PHY 4
700 means that the PHY with address 4 is connected to FEC1
702 When set to -1, means to probe for first available.
704 config FEC2_PHY_NORXERR
706 depends on ETHER_ON_FEC2
709 The PHY does not have a RXERR line (RMII only).
710 (so program the FEC to ignore it).
712 config SYS_DPAA_QBMAN
713 bool "Device tree fixup for QBMan on freescale SOCs"
714 depends on (ARM || PPC) && !SPL_BUILD
715 default y if ARCH_B4860 || \
732 QBman fixups to allow deep sleep in DPAA 1 SOCs
736 bool "Enable Three-Speed Ethernet Controller"
738 This driver implements support for the (Enhanced) Three-Speed
739 Ethernet Controller found on Freescale SoCs.
742 bool "MediaTek Ethernet GMAC Driver"
748 This Driver support MediaTek Ethernet GMAC
749 Say Y to enable support for the MediaTek Ethernet GMAC.
751 config HIGMACV300_ETH
752 bool "HiSilicon Gigabit Ethernet Controller"
757 This driver supports HIGMACV300 Ethernet controller found on
761 bool "NXP ENETC Ethernet controller"
762 depends on DM_PCI && DM_ETH && DM_MDIO
764 This driver supports the NXP ENETC Ethernet controller found on some
767 config MDIO_MUX_I2CREG
768 bool "MDIO MUX accessed as a register over I2C"
769 depends on DM_MDIO_MUX && DM_I2C
771 This driver is used for MDIO muxes driven by writing to a register of
772 an I2C chip. The board it was developed for uses a mux controlled by
773 on-board FPGA which in turn is accessed as a chip over I2C.
776 bool "Qualcomm IPQ4019 MDIO interface support"
779 This driver supports the MDIO interface found in Qualcomm
780 IPQ40xx series Soc-s.
783 bool "Marvell MDIO interface support"
786 This driver supports the MDIO interface found in the network
787 interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
788 Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP).
790 This driver is used by the MVPP2 and MVNETA drivers.
793 bool "NXP Layerscape MDIO interface support"
796 This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and
797 on the mEMAC (which supports both Clauses 22 and 45).
799 config MDIO_MUX_MMIOREG
800 bool "MDIO MUX accessed as a MMIO register access"
801 depends on DM_MDIO_MUX
803 This driver is used for MDIO muxes driven by writing to a register in
804 the MMIO physical memory.
806 config MDIO_MUX_MESON_G12A
807 bool "MDIO MUX for Amlogic Meson G12A SoCs"
808 depends on DM_MDIO_MUX
810 This driver is used for the MDIO mux found on the Amlogic G12A & compatible