From aedc0e520e5ae9ba1342c25c4604d18fb236c2bc Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Tue, 9 May 2006 00:58:28 +0400 Subject: [PATCH] Fix RTL8019AS init for Toshiba RBTX49xx boards Ensure that 8-bit mode is selected for the on-board Realtek RTL8019AS chip on Toshiba RBHMA4x00, get rid of the duplicate #ifdef's when setting ei_status.word16. The chip's datasheet says that the PSTOP register shouldn't exceed 0x60 in 8-bit mode -- ensure this too. Signed-off-by: Sergei Shtylyov Signed-off-by: Stephen Hemminger --- drivers/net/ne.c | 31 +++++++++++++++++++------------ 1 file changed, 19 insertions(+), 12 deletions(-) diff --git a/drivers/net/ne.c b/drivers/net/ne.c index 93c494bcd18d..b32765215f75 100644 --- a/drivers/net/ne.c +++ b/drivers/net/ne.c @@ -139,8 +139,9 @@ bad_clone_list[] __initdata = { #if defined(CONFIG_PLAT_MAPPI) # define DCR_VAL 0x4b -#elif defined(CONFIG_PLAT_OAKS32R) -# define DCR_VAL 0x48 +#elif defined(CONFIG_PLAT_OAKS32R) || \ + defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938) +# define DCR_VAL 0x48 /* 8-bit mode */ #else # define DCR_VAL 0x49 #endif @@ -396,10 +397,22 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr) /* We must set the 8390 for word mode. */ outb_p(DCR_VAL, ioaddr + EN0_DCFG); start_page = NESM_START_PG; - stop_page = NESM_STOP_PG; + + /* + * Realtek RTL8019AS datasheet says that the PSTOP register + * shouldn't exceed 0x60 in 8-bit mode. + * This chip can be identified by reading the signature from + * the remote byte count registers (otherwise write-only)... + */ + if ((DCR_VAL & 0x01) == 0 && /* 8-bit mode */ + inb(ioaddr + EN0_RCNTLO) == 0x50 && + inb(ioaddr + EN0_RCNTHI) == 0x70) + stop_page = 0x60; + else + stop_page = NESM_STOP_PG; } else { start_page = NE1SM_START_PG; - stop_page = NE1SM_STOP_PG; + stop_page = NE1SM_STOP_PG; } #if defined(CONFIG_PLAT_MAPPI) || defined(CONFIG_PLAT_OAKS32R) @@ -509,15 +522,9 @@ static int __init ne_probe1(struct net_device *dev, int ioaddr) ei_status.name = name; ei_status.tx_start_page = start_page; ei_status.stop_page = stop_page; -#if defined(CONFIG_TOSHIBA_RBTX4927) || defined(CONFIG_TOSHIBA_RBTX4938) - wordlength = 1; -#endif -#ifdef CONFIG_PLAT_OAKS32R - ei_status.word16 = 0; -#else - ei_status.word16 = (wordlength == 2); -#endif + /* Use 16-bit mode only if this wasn't overridden by DCR_VAL */ + ei_status.word16 = (wordlength == 2 && (DCR_VAL & 0x01)); ei_status.rx_start_page = start_page + TX_PAGES; #ifdef PACKETBUF_MEMSIZE -- 2.39.2