pandora-kernel.git
9 years agoBluetooth: Change signature of smp_conn_security()
Vinicius Costa Gomes [Fri, 24 Aug 2012 00:32:43 +0000 (21:32 -0300)]
Bluetooth: Change signature of smp_conn_security()

commit cc110922da7e902b62d18641a370fec01a9fa794 upstream.

To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.

This also makes it clear that it is checking the security of the link.

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agommc: Prevent 1.8V switch for SD hosts that don't support UHS modes.
Al Cooper [Fri, 16 Mar 2012 19:54:17 +0000 (15:54 -0400)]
mmc: Prevent 1.8V switch for SD hosts that don't support UHS modes.

commit 4188bba0e9e7ba58d231b528df495666f2742b74 upstream.

The driver should not try to switch to 1.8V when the SD 3.0 host
controller does not have any UHS capabilities bits set (SDR50, DDR50
or SDR104). See page 72 of "SD Specifications Part A2 SD Host
Controller Simplified Specification Version 3.00" under
"1.8V Signaling Enable". Instead of setting SDR12 and SDR25 in the host
capabilities data structure for all V3.0 host controllers, only set them
if SDR104, SDR50 or DDR50 is set in the host capabilities register. This
will prevent the switch to 1.8V later.

Signed-off-by: Al Cooper <acooper@gmail.com>
Acked-by: Arindam Nath <arindam.nath@amd.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Acked-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoPrevent interface errors with Seagate FreeAgent GoFlex
Daniel J Blueman [Mon, 23 Jul 2012 04:22:37 +0000 (12:22 +0800)]
Prevent interface errors with Seagate FreeAgent GoFlex

commit c531077f40abc9f2129c4c83a30b3f8d6ce1c0e7 upstream.

When using my Seagate FreeAgent GoFlex eSATAp external disk enclosure,
interface errors are always seen until 1.5Gbps is negotiated [1]. This
occurs using any disk in the enclosure, and when the disk is connected
directly with a generic passive eSATAp cable, we see stable 3Gbps
operation as expected.

Blacklist 3Gbps mode to avoid dataloss and the ~30s delay bus reset
and renegotiation incurs.

Signed-off-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agords: set correct msg_namelen
Weiping Pan [Mon, 23 Jul 2012 02:37:48 +0000 (10:37 +0800)]
rds: set correct msg_namelen

commit 06b6a1cf6e776426766298d055bb3991957d90a7 upstream.

Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.

And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.

How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.

1 compile
gcc -o rds_client rds_client.c
gcc -o rds_server rds_server.c

2 run ./rds_server on one console

3 run ./rds_client on another console

4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor

/***************** rds_client.c ********************/

int main(void)
{
int sock_fd;
struct sockaddr_in serverAddr;
struct sockaddr_in toAddr;
char recvBuffer[128] = "data from client";
struct msghdr msg;
struct iovec iov;

sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if (sock_fd < 0) {
perror("create socket error\n");
exit(1);
}

memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4001);

if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind() error\n");
close(sock_fd);
exit(1);
}

memset(&toAddr, 0, sizeof(toAddr));
toAddr.sin_family = AF_INET;
toAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
toAddr.sin_port = htons(4000);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = strlen(recvBuffer) + 1;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;

if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendto() error\n");
close(sock_fd);
exit(1);
}

printf("client send data:%s\n", recvBuffer);

memset(recvBuffer, '\0', 128);

msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}

printf("receive data from server:%s\n", recvBuffer);

close(sock_fd);

return 0;
}

/***************** rds_server.c ********************/

int main(void)
{
struct sockaddr_in fromAddr;
int sock_fd;
struct sockaddr_in serverAddr;
unsigned int addrLen;
char recvBuffer[128];
struct msghdr msg;
struct iovec iov;

sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if(sock_fd < 0) {
perror("create socket error\n");
exit(0);
}

memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4000);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind error\n");
close(sock_fd);
exit(1);
}

printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;

/*
 * I add 16 to sizeof(fromAddr), ie 32,
 * and pay attention to the definition of fromAddr,
 * recvmsg() will overwrite sock_fd,
 * since kernel will copy 32 bytes to userspace.
 *
 * If you just use sizeof(fromAddr), it works fine.
 * */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;

while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}

close(sock_fd);
return 0;
}

Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoFix a dead loop in async_synchronize_full()
Li Zhong [Tue, 24 Jul 2012 22:02:49 +0000 (15:02 -0700)]
Fix a dead loop in async_synchronize_full()

[Fixed upstream by commits 2955b47d2c1983998a8c5915cb96884e67f7cb53 and
a4683487f90bfe3049686fc5c566bdc1ad03ace6 from Dan Williams, but they are much
more intrusive than this tiny fix, according to Andrew - gregkh]

This patch tries to fix a dead loop in  async_synchronize_full(), which
could be seen when preemption is disabled on a single cpu machine.

void async_synchronize_full(void)
{
        do {
                async_synchronize_cookie(next_cookie);
        } while (!list_empty(&async_running) || !
list_empty(&async_pending));
}

async_synchronize_cookie() calls async_synchronize_cookie_domain() with
&async_running as the default domain to synchronize.

However, there might be some works in the async_pending list from other
domains. On a single cpu system, without preemption, there is no chance
for the other works to finish, so async_synchronize_full() enters a dead
loop.

It seems async_synchronize_full() wants to synchronize all entries in
all running lists(domains), so maybe we could just check the entry_count
to know whether all works are finished.

Currently, async_synchronize_cookie_domain() expects a non-NULL running
list ( if NULL, there would be NULL pointer dereference ), so maybe a
NULL pointer could be used as an indication for the functions to
synchronize all works in all domains.

Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agonet: Statically initialize init_net.dev_base_head
Rustad, Mark D [Wed, 18 Jul 2012 09:06:07 +0000 (09:06 +0000)]
net: Statically initialize init_net.dev_base_head

commit 734b65417b24d6eea3e3d7457e1f11493890ee1d upstream.

This change eliminates an initialization-order hazard most
recently seen when netprio_cgroup is built into the kernel.

With thanks to Eric Dumazet for catching a bug.

Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoBluetooth: Add support for Apple vendor-specific devices
Henrik Rydberg [Sat, 25 Aug 2012 17:28:06 +0000 (19:28 +0200)]
Bluetooth: Add support for Apple vendor-specific devices

commit 1fa6535faf055cd71311ab887e94fc234f04ee18 upstream.

As pointed out by Gustavo and Marcel, all Apple-specific Broadcom
devices seen so far have the same interface class, subclass and
protocol numbers. This patch adds an entry which matches all of them,
using the new USB_VENDOR_AND_INTERFACE_INFO() macro.

In particular, this patch adds support for the MacBook Pro Retina
(05ac:8286), which is not in the present list.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Shea Levy <shea@shealevy.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoBluetooth: Use USB_VENDOR_AND_INTERFACE() for Broadcom devices
Gustavo Padovan [Mon, 6 Aug 2012 18:36:49 +0000 (15:36 -0300)]
Bluetooth: Use USB_VENDOR_AND_INTERFACE() for Broadcom devices

commit 92c385f46b30f4954e9dd2d2005c12d233b479ea upstream.

Many Broadcom devices has a vendor specific devices class, with this rule
we match all existent and future controllers with this behavior.

We also remove old rules to that matches product id for Broadcom devices.

Tested-by: John Hommel <john.hommel@hp.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoBluetooth: btusb: Add vendor specific ID (0a5c:21f4) BCM20702A0
Manoj Iyer [Tue, 10 Jul 2012 19:07:38 +0000 (14:07 -0500)]
Bluetooth: btusb: Add vendor specific ID (0a5c:21f4) BCM20702A0

commit 61c964ba1748e984cb232b431582815899bf10fe upstream.

Patch adds support for BCM20702A0 device id (0a5c:21f4).

usb-devices after patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

usb-devices before patch was applied:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a5c ProdID=21f4 Rev=01.12
S: Manufacturer=Broadcom Corp
S: Product=BCM20702A0
S: SerialNumber=E4D53DF154D6
C: #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: Chris Gagnon <chris.gagnon@canonical.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoasus-laptop: HRWS/HWRS typo
Corentin Chary [Mon, 20 Aug 2012 21:01:51 +0000 (23:01 +0200)]
asus-laptop: HRWS/HWRS typo

commit 8871e99f89b7d7b1ea99de550eea2a56273f42ab upstream.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=24222
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoUSB: Fix race condition when removing host controllers
Alan Stern [Wed, 26 Sep 2012 17:09:53 +0000 (13:09 -0400)]
USB: Fix race condition when removing host controllers

commit 0d00dc2611abbe6ad244d50569c2ee82ce42846c upstream.

This patch (as1607) fixes a race that can occur if a USB host
controller is removed while a process is reading the
/sys/kernel/debug/usb/devices file.

The usb_device_read() routine uses the bus->root_hub pointer to
determine whether or not the root hub is registered.  The is not a
valid test, because the pointer is set before the root hub gets
registered and remains set even after the root hub is unregistered and
deallocated.  As a result, usb_device_read() or usb_device_dump() can
access freed memory, causing an oops.

The patch changes the test to use the hcd->rh_registered flag, which
does get set and cleared at the appropriate times.  It also makes sure
to hold the usb_bus_list_lock mutex while setting the flag, so that
usb_device_read() will become aware of new root hubs as soon as they
are registered.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agomd/raid10: fix "enough" function for detecting if array is failed.
NeilBrown [Thu, 27 Sep 2012 02:35:21 +0000 (12:35 +1000)]
md/raid10: fix "enough" function for detecting if array is failed.

commit 80b4812407c6b1f66a4f2430e69747a13f010839 upstream.

The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.

So change it to make this number explicit.

This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.

Reported-by: Jakub Husák <jakub@gooseman.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
[bwh: Backported to 3.2: s/geo->/conf->/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodm table: clear add_random unless all devices have it set
Milan Broz [Wed, 26 Sep 2012 22:45:43 +0000 (23:45 +0100)]
dm table: clear add_random unless all devices have it set

commit c3c4555edd10dbc0b388a0125b9c50de5e79af05 upstream.

Always clear QUEUE_FLAG_ADD_RANDOM if any underlying device does not
have it set. Otherwise devices with predictable characteristics may
contribute entropy.

QUEUE_FLAG_ADD_RANDOM specifies whether or not queue IO timings
contribute to the random pool.

For bio-based targets this flag is always 0 because such devices have no
real queue.

For request-based devices this flag was always set to 1 by default.

Now set it according to the flags on underlying devices. If there is at
least one device which should not contribute, set the flag to zero: If a
device, such as fast SSD storage, is not suitable for supplying entropy,
a request-based queue stacked over it will not be either.

Because the checking logic is exactly same as for the rotational flag,
share the iteration function with device_is_nonrot().

Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodm: handle requests beyond end of device instead of using BUG_ON
Mike Snitzer [Wed, 26 Sep 2012 22:45:42 +0000 (23:45 +0100)]
dm: handle requests beyond end of device instead of using BUG_ON

commit ba1cbad93dd47223b1f3b8edd50dd9ef2abcb2ed upstream.

The access beyond the end of device BUG_ON that was introduced to
dm_request_fn via commit 29e4013de7ad950280e4b2208 ("dm: implement
REQ_FLUSH/FUA support for request-based dm") was an overly
drastic (but simple) response to this situation.

I have received a report that this BUG_ON was hit and now think
it would be better to use dm_kill_unmapped_request() to fail the clone
and original request with -EIO.

map_request() will assign the valid target returned by
dm_table_find_target to tio->ti.  But when the target
isn't valid tio->ti is never assigned (because map_request isn't
called); so add a check for tio->ti != NULL to dm_done().

Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agosb_edac: Avoid overflow errors at memory size calculation
Mauro Carvalho Chehab [Thu, 20 Sep 2012 15:09:30 +0000 (12:09 -0300)]
sb_edac: Avoid overflow errors at memory size calculation

commit deb09ddaff1435f72dd598d38f9b58354c68a5ec upstream.

Sandy bridge EDAC is calculating the memory size with overflow.
Basically, the size field and the integer calculation is using 32 bits.
More bits are needed, when the DIMM memories have high density.

The net result is that memories are improperly reported there, when
high-density DIMMs are used:

EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 0, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 591: mc#0: channel 1, dimm 0, -16384 Mb (-4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800

As the number of pages value is handled at the EDAC core as unsigned
ints, the driver shows the 16 GB memories at sysfs interface as 16760832
MB! The fix is simple: calculate the number of pages as unsigned 64-bits
integer.

After the patch, the memory size (16 GB) is properly detected:

EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 0, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800
EDAC DEBUG: in drivers/edac/sb_edac.c, line at 592: mc#0: channel 1, dimm 0, 16384 Mb (4194304 pages) bank: 8, rank: 2, row: 0x10000, col: 0x800

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[bwh: Backported to 3.2:
 - Adjust context
 - Debug log function is debugf0(), not edac_dbg()]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agogpio-lpc32xx: Fix value handling of gpio_direction_output()
Roland Stigge [Thu, 20 Sep 2012 08:48:03 +0000 (10:48 +0200)]
gpio-lpc32xx: Fix value handling of gpio_direction_output()

commit b1268d3737c6316016026245eef276eda6b0a621 upstream.

For GPIOs of gpio-lpc32xx, gpio_direction_output() ignores the value argument
(initial value of output). This patch fixes this by setting the level
accordingly.

Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoxen/boot: Disable NUMA for PV guests.
Konrad Rzeszutek Wilk [Fri, 17 Aug 2012 14:22:37 +0000 (10:22 -0400)]
xen/boot: Disable NUMA for PV guests.

commit 8d54db795dfb1049d45dc34f0dddbc5347ec5642 upstream.

The hypervisor is in charge of allocating the proper "NUMA" memory
and dealing with the CPU scheduler to keep them bound to the proper
NUMA node. The PV guests (and PVHVM) have no inkling of where they
run and do not need to know that right now. In the future we will
need to inject NUMA configuration data (if a guest spans two or more
NUMA nodes) so that the kernel can make the right choices. But those
patches are not yet present.

In the meantime, disable the NUMA capability in the PV guest, which
also fixes a bootup issue. Andre says:

"we see Dom0 crashes due to the kernel detecting the NUMA topology not
by ACPI, but directly from the northbridge (CONFIG_AMD_NUMA).

This will detect the actual NUMA config of the physical machine, but
will crash about the mismatch with Dom0's virtual memory. Variation of
the theme: Dom0 sees what it's not supposed to see.

This happens with the said config option enabled and on a machine where
this scanning is still enabled (K8 and Fam10h, not Bulldozer class)

We have this dump then:
NUMA: Warning: node ids are out of bound, from=-1 to=-1 distance=10
Scanning NUMA topology in Northbridge 24
Number of physical nodes 4
Node 0 MemBase 0000000000000000 Limit 0000000040000000
Node 1 MemBase 0000000040000000 Limit 0000000138000000
Node 2 MemBase 0000000138000000 Limit 00000001f8000000
Node 3 MemBase 00000001f8000000 Limit 0000000238000000
Initmem setup node 0 0000000000000000-0000000040000000
  NODE_DATA [000000003ffd9000 - 000000003fffffff]
Initmem setup node 1 0000000040000000-0000000138000000
  NODE_DATA [0000000137fd9000 - 0000000137ffffff]
Initmem setup node 2 0000000138000000-00000001f8000000
  NODE_DATA [00000001f095e000 - 00000001f0984fff]
Initmem setup node 3 00000001f8000000-0000000238000000
Cannot find 159744 bytes in node 3
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96
Pid: 0, comm: swapper Not tainted 3.3.6 #1 AMD Dinar/Dinar
RIP: e030:[<ffffffff81d220e6>]  [<ffffffff81d220e6>] __alloc_bootmem_node+0x43/0x96
.. snip..
  [<ffffffff81d23024>] sparse_early_usemaps_alloc_node+0x64/0x178
  [<ffffffff81d23348>] sparse_init+0xe4/0x25a
  [<ffffffff81d16840>] paging_init+0x13/0x22
  [<ffffffff81d07fbb>] setup_arch+0x9c6/0xa9b
  [<ffffffff81683954>] ? printk+0x3c/0x3e
  [<ffffffff81d01a38>] start_kernel+0xe5/0x468
  [<ffffffff81d012cf>] x86_64_start_reservations+0xba/0xc1
  [<ffffffff81007153>] ? xen_setup_runstate_info+0x2c/0x36
  [<ffffffff81d050ee>] xen_start_kernel+0x565/0x56c
"

so we just disable NUMA scanning by setting numa_off=1.

Reported-and-Tested-by: Andre Przywara <andre.przywara@amd.com>
Acked-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agohwmon: (fam15h_power) Tweak runavg_range on resume
Andreas Herrmann [Sun, 23 Sep 2012 18:27:32 +0000 (20:27 +0200)]
hwmon: (fam15h_power) Tweak runavg_range on resume

commit 5f0ecb907deb1e6f28071ee3bd568903b9da1be4 upstream.

The quirk introduced with commit
00250ec90963b7ef6678438888f3244985ecde14 (hwmon: fam15h_power: fix
bogus values with current BIOSes) is not only required during driver
load but also when system resumes from suspend. The BIOS might set the
previously recommended (but unsuitable) initilization value for the
running average range register during resume.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoHID: Fix logitech-dj: missing Unifying device issue
Nestor Lopez Casado [Fri, 21 Sep 2012 10:21:34 +0000 (12:21 +0200)]
HID: Fix logitech-dj: missing Unifying device issue

commit 596264082f10dd4a567c43d4526b2f54ac5520bc upstream.

This patch fixes an issue introduced after commit 4ea5454203d991ec
("HID: Fix race condition between driver core and ll-driver").

After that commit, hid-core discards any incoming packet that arrives while
hid driver's probe function is being executed.

This broke the enumeration process of hid-logitech-dj, that must receive
control packets in-band with the mouse and keyboard packets. Discarding mouse
or keyboard data at the very begining is usually fine, but it is not the case
for control packets.

This patch forces a re-enumeration of the paired devices when a packet arrives
that comes from an unknown device.

Based on a patch originally written by Benjamin Tissoires.

Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodj: memory scribble in logi_dj
Alan Cox [Tue, 4 Sep 2012 14:10:08 +0000 (15:10 +0100)]
dj: memory scribble in logi_dj

commit 8a55ade76551e3927b4e41ee9e7751875d18bc25 upstream.

Allocate a structure not a pointer to it !

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoHID: logitech: don't use stack based dj_report structures
Marc Dionne [Fri, 1 Jun 2012 22:12:14 +0000 (18:12 -0400)]
HID: logitech: don't use stack based dj_report structures

commit d8dc3494f77a5cc3b274bae36f7e74e85cf8a407 upstream.

On a system with a logitech wireless keyboard/mouse and DMA-API debugging
enabled, this warning appears at boot:

kernel: WARNING: at lib/dma-debug.c:929 check_for_stack.part.12+0x70/0xa7()
kernel: Hardware name: MS-7593
kernel: uhci_hcd 0000:00:1d.1: DMA-API: device driver maps memory fromstack [addr=ffff8801b0079c29]

Make logi_dj_recv_query_paired_devices and logi_dj_recv_switch_to_dj_mode
use a structure allocated with kzalloc rather than a stack based one.

Signed-off-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoHID: logitech: fix mask to enable DJ mode
Nestor Lopez Casado [Thu, 2 Feb 2012 09:54:14 +0000 (10:54 +0100)]
HID: logitech: fix mask to enable DJ mode

commit 765031668fb2b064aebd9a568e5ad794cbe3413a upstream.

The user can only experience the bug if she pairs 6 devices to a Unifying
receiver. The sixth paired device would not work.

The value changed is actually a bitmask that enables reporting from each
paired device. As the sixth bit was not set, the sixth device reports are
ignored by the receiver and never get to the driver.

Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
 drivers/hid/hid-logitech-dj.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agocan: ti_hecc: fix oops during rmmod
Marc Kleine-Budde [Wed, 19 Sep 2012 12:58:45 +0000 (14:58 +0200)]
can: ti_hecc: fix oops during rmmod

commit ab04c8bd423edb03e2148350a091836c196107fc upstream.

This patch fixes an oops which occurs when unloading the driver, while the
network interface is still up. The problem is that first the io mapping is
teared own, then the CAN device is unregistered, resulting in accessing the
hardware's iomem:

[  172.744232] Unable to handle kernel paging request at virtual address c88b0040
[  172.752441] pgd = c7be4000
[  172.755645] [c88b0040] *pgd=87821811, *pte=00000000, *ppte=00000000
[  172.762207] Internal error: Oops: 807 [#1] PREEMPT ARM
[  172.767517] Modules linked in: ti_hecc(-) can_dev
[  172.772430] CPU: 0    Not tainted  (3.5.0alpha-00037-g3554cc0 #126)
[  172.778961] PC is at ti_hecc_close+0xb0/0x100 [ti_hecc]
[  172.784423] LR is at __dev_close_many+0x90/0xc0
[  172.789123] pc : [<bf00c768>]    lr : [<c033be58>]    psr: 60000013
[  172.789123] sp : c5c1de68  ip : 00040081  fp : 00000000
[  172.801025] r10: 00000001  r9 : c5c1c000  r8 : 00100100
[  172.806457] r7 : c5d0a48c  r6 : c5d0a400  r5 : 00000000  r4 : c5d0a000
[  172.813232] r3 : c88b0000  r2 : 00000001  r1 : c5d0a000  r0 : c5d0a000
[  172.820037] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
[  172.827423] Control: 10c5387d  Table: 87be4019  DAC: 00000015
[  172.833404] Process rmmod (pid: 600, stack limit = 0xc5c1c2f0)
[  172.839447] Stack: (0xc5c1de68 to 0xc5c1e000)
[  172.843994] de60:                   bf00c6b8 c5c1dec8 c5d0a000 c5d0a000 00200200 c033be58
[  172.852478] de80: c5c1de44 c5c1dec8 c5c1dec8 c033bf2c c5c1de90 c5c1de90 c5d0a084 c5c1de44
[  172.860992] dea0: c5c1dec8 c033c098 c061d3dc c5d0a000 00000000 c05edf28 c05edb34 c000d724
[  172.869476] dec0: 00000000 c033c2f8 c5d0a084 c5d0a084 00000000 c033c370 00000000 c5d0a000
[  172.877990] dee0: c05edb00 c033c3b8 c5d0a000 bf00d3ac c05edb00 bf00d7c8 bf00d7c8 c02842dc
[  172.886474] df00: c02842c8 c0282f90 c5c1c000 c05edb00 bf00d7c8 c0283668 bf00d7c8 00000000
[  172.894989] df20: c0611f98 befe2f80 c000d724 c0282d10 bf00d804 00000000 00000013 c0068a8c
[  172.903472] df40: c5c538e8 685f6974 00636365 c61571a8 c5cb9980 c61571a8 c6158a20 c00c9bc4
[  172.911987] df60: 00000000 00000000 c5cb9980 00000000 c5cb9980 00000000 c7823680 00000006
[  172.920471] df80: bf00d804 00000880 c5c1df8c 00000000 000d4267 befe2f80 00000001 b6d90068
[  172.928985] dfa0: 00000081 c000d5a0 befe2f80 00000001 befe2f80 00000880 b6d90008 00000008
[  172.937469] dfc0: befe2f80 00000001 b6d90068 00000081 00000001 00000000 befe2eac 00000000
[  172.945983] dfe0: 00000000 befe2b18 00023ba4 b6e6addc 60000010 befe2f80 a8e00190 86d2d344
[  172.954498] [<bf00c768>] (ti_hecc_close+0xb0/0x100 [ti_hecc]) from [<c033be58>] (__dev__registered_many+0xc0/0x2a0)
[  172.984161] [<c033c098>] (rollback_registered_many+0xc0/0x2a0) from [<c033c2f8>] (rollback_registered+0x20/0x30)
[  172.994750] [<c033c2f8>] (rollback_registered+0x20/0x30) from [<c033c370>] (unregister_netdevice_queue+0x68/0x98)
[  173.005401] [<c033c370>] (unregister_netdevice_queue+0x68/0x98) from [<c033c3b8>] (unregister_netdev+0x18/0x20)
[  173.015899] [<c033c3b8>] (unregister_netdev+0x18/0x20) from [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc])
[  173.026245] [<bf00d3ac>] (ti_hecc_remove+0x60/0x80 [ti_hecc]) from [<c02842dc>] (platform_drv_remove+0x14/0x18)
[  173.036712] [<c02842dc>] (platform_drv_remove+0x14/0x18) from [<c0282f90>] (__device_release_driver+0x7c/0xbc)

Cc: Anant Gole <anantgole@ti.com>
Tested-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agocan: janz-ican3: fix support for older hardware revisions
Ira W. Snyder [Tue, 11 Sep 2012 22:58:15 +0000 (15:58 -0700)]
can: janz-ican3: fix support for older hardware revisions

commit e21093ef6fb4cbecdf926102286dbe280ae965db upstream.

The Revision 1.0 Janz CMOD-IO Carrier Board does not have support for
the reset registers. To support older hardware, the code is changed to
use the hardware reset register on the Janz VMOD-ICAN3 hardware itself.

Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agotracing: Don't call page_to_pfn() if page is NULL
Wen Congyang [Thu, 20 Sep 2012 06:04:47 +0000 (14:04 +0800)]
tracing: Don't call page_to_pfn() if page is NULL

commit 85f2a2ef1d0ab99523e0b947a2b723f5650ed6aa upstream.

When allocating memory fails, page is NULL. page_to_pfn() will
cause the kernel panicked if we don't use sparsemem vmemmap.

Link: http://lkml.kernel.org/r/505AB1FF.8020104@cn.fujitsu.com
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoInput: i8042 - disable mux on Toshiba C850D
Anisse Astier [Wed, 19 Sep 2012 18:10:48 +0000 (11:10 -0700)]
Input: i8042 - disable mux on Toshiba C850D

commit 8669cf6793bb38307a30fb6b9565ddc8840ebd3f upstream.

On Toshiba Satellite C850D, the touchpad and the keyboard might randomly
not work at boot. Preventing MUX mode activation solves this issue.

Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoasix: Support DLink DUB-E100 H/W Ver C1
Søren holm [Mon, 17 Sep 2012 21:50:57 +0000 (21:50 +0000)]
asix: Support DLink DUB-E100 H/W Ver C1

commit ed3770a9cd5764a575b83810ea679bbff2b03082 upstream.

Signed-off-by: Søren Holm <sgh@sgh.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: adjust filename]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoxen/boot: Disable BIOS SMP MP table search.
Konrad Rzeszutek Wilk [Wed, 19 Sep 2012 12:30:55 +0000 (08:30 -0400)]
xen/boot: Disable BIOS SMP MP table search.

commit bd49940a35ec7d488ae63bd625639893b3385b97 upstream.

As the initial domain we are able to search/map certain regions
of memory to harvest configuration data. For all low-level we
use ACPI tables - for interrupts we use exclusively ACPI _PRT
(so DSDT) and MADT for INT_SRC_OVR.

The SMP MP table is not used at all. As a matter of fact we do
not even support machines that only have SMP MP but no ACPI tables.

Lets follow how Moorestown does it and just disable searching
for BIOS SMP tables.

This also fixes an issue on HP Proliant BL680c G5 and DL380 G6:

9f->100 for 1:1 PTE
Freeing 9f-100 pfn range: 97 pages freed
1-1 mapping on 9f->100
.. snip..
e820: BIOS-provided physical RAM map:
Xen: [mem 0x0000000000000000-0x000000000009efff] usable
Xen: [mem 0x000000000009f400-0x00000000000fffff] reserved
Xen: [mem 0x0000000000100000-0x00000000cfd1dfff] usable
.. snip..
Scan for SMP in [mem 0x00000000-0x000003ff]
Scan for SMP in [mem 0x0009fc00-0x0009ffff]
Scan for SMP in [mem 0x000f0000-0x000fffff]
found SMP MP-table at [mem 0x000f4fa0-0x000f4faf] mapped at [ffff8800000f4fa0]
(XEN) mm.c:908:d0 Error getting mfn 100 (pfn 5555555555555555) from L1 entry 0000000000100461 for l1e_owner=0, pg_owner=0
(XEN) mm.c:4995:d0 ptwr_emulate: could not get_page_from_l1e()
BUG: unable to handle kernel NULL pointer dereference at           (null)
IP: [<ffffffff81ac07e2>] xen_set_pte_init+0x66/0x71
. snip..
Pid: 0, comm: swapper Not tainted 3.6.0-rc6upstream-00188-gb6fb969-dirty #2 HP ProLiant BL680c G5
.. snip..
Call Trace:
 [<ffffffff81ad31c6>] __early_ioremap+0x18a/0x248
 [<ffffffff81624731>] ? printk+0x48/0x4a
 [<ffffffff81ad32ac>] early_ioremap+0x13/0x15
 [<ffffffff81acc140>] get_mpc_size+0x2f/0x67
 [<ffffffff81acc284>] smp_scan_config+0x10c/0x136
 [<ffffffff81acc2e4>] default_find_smp_config+0x36/0x5a
 [<ffffffff81ac3085>] setup_arch+0x5b3/0xb5b
 [<ffffffff81624731>] ? printk+0x48/0x4a
 [<ffffffff81abca7f>] start_kernel+0x90/0x390
 [<ffffffff81abc356>] x86_64_start_reservations+0x131/0x136
 [<ffffffff81abfa83>] xen_start_kernel+0x65f/0x661
(XEN) Domain 0 crashed: 'noreboot' set - not rebooting.

which is that ioremap would end up mapping 0xff using _PAGE_IOMAP
(which is what early_ioremap sticks as a flag) - which meant
we would get MFN 0xFF (pte ff461, which is OK), and then it would
also map 0x100 (b/c ioremap tries to get page aligned request, and
it was trying to map 0xf4fa0 + PAGE_SIZE - so it mapped the next page)
as _PAGE_IOMAP. Since 0x100 is actually a RAM page, and the _PAGE_IOMAP
bypasses the P2M lookup we would happily set the PTE to 1000461.
Xen would deny the request since we do not have access to the
Machine Frame Number (MFN) of 0x100. The P2M[0x100] is for example
0x80140.

Fixes-Oracle-Bugzilla: https://bugzilla.oracle.com/bugzilla/show_bug.cgi?id=13665
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agocfg80211: fix possible circular lock on reg_regdb_search()
Luis R. Rodriguez [Fri, 14 Sep 2012 22:36:57 +0000 (15:36 -0700)]
cfg80211: fix possible circular lock on reg_regdb_search()

commit a85d0d7f3460b1a123b78e7f7e39bf72c37dfb78 upstream.

When call_crda() is called we kick off a witch hunt search
for the same regulatory domain on our internal regulatory
database and that work gets kicked off on a workqueue, this
is done while the cfg80211_mutex is held. If that workqueue
kicks off it will first lock reg_regdb_search_mutex and
later cfg80211_mutex but to ensure two CPUs will not contend
against cfg80211_mutex the right thing to do is to have the
reg_regdb_search() wait until the cfg80211_mutex is let go.

The lockdep report is pasted below.

cfg80211: Calling CRDA to update world regulatory domain

======================================================
[ INFO: possible circular locking dependency detected ]
3.3.8 #3 Tainted: G           O
-------------------------------------------------------
kworker/0:1/235 is trying to acquire lock:
 (cfg80211_mutex){+.+...}, at: [<816468a4>] set_regdom+0x78c/0x808 [cfg80211]

but task is already holding lock:
 (reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (reg_regdb_search_mutex){+.+...}:
       [<800a8384>] lock_acquire+0x60/0x88
       [<802950a8>] mutex_lock_nested+0x54/0x31c
       [<81645778>] is_world_regdom+0x9f8/0xc74 [cfg80211]

-> #1 (reg_mutex#2){+.+...}:
       [<800a8384>] lock_acquire+0x60/0x88
       [<802950a8>] mutex_lock_nested+0x54/0x31c
       [<8164539c>] is_world_regdom+0x61c/0xc74 [cfg80211]

-> #0 (cfg80211_mutex){+.+...}:
       [<800a77b8>] __lock_acquire+0x10d4/0x17bc
       [<800a8384>] lock_acquire+0x60/0x88
       [<802950a8>] mutex_lock_nested+0x54/0x31c
       [<816468a4>] set_regdom+0x78c/0x808 [cfg80211]

other info that might help us debug this:

Chain exists of:
  cfg80211_mutex --> reg_mutex#2 --> reg_regdb_search_mutex

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(reg_regdb_search_mutex);
                               lock(reg_mutex#2);
                               lock(reg_regdb_search_mutex);
  lock(cfg80211_mutex);

 *** DEADLOCK ***

3 locks held by kworker/0:1/235:
 #0:  (events){.+.+..}, at: [<80089a00>] process_one_work+0x230/0x460
 #1:  (reg_regdb_work){+.+...}, at: [<80089a00>] process_one_work+0x230/0x460
 #2:  (reg_regdb_search_mutex){+.+...}, at: [<81646828>] set_regdom+0x710/0x808 [cfg80211]

stack backtrace:
Call Trace:
[<80290fd4>] dump_stack+0x8/0x34
[<80291bc4>] print_circular_bug+0x2ac/0x2d8
[<800a77b8>] __lock_acquire+0x10d4/0x17bc
[<800a8384>] lock_acquire+0x60/0x88
[<802950a8>] mutex_lock_nested+0x54/0x31c
[<816468a4>] set_regdom+0x78c/0x808 [cfg80211]

Reported-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agocifs: fix return value in cifsConvertToUTF16
Jeff Layton [Tue, 18 Sep 2012 18:21:01 +0000 (14:21 -0400)]
cifs: fix return value in cifsConvertToUTF16

commit c73f693989d7a7d99ec66a7065295a0c93d0b127 upstream.

This function returns the wrong value, which causes the callers to get
the length of the resulting pathname wrong when it contains non-ASCII
characters.

This seems to fix https://bugzilla.samba.org/show_bug.cgi?id=6767

Reported-by: Baldvin Kovacs <baldvin.kovacs@gmail.com>
Reported-and-Tested-by: Nicolas Lefebvre <nico.lefebvre@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agohwmon: (ad7314) Add 'name' sysfs attribute
Guenter Roeck [Tue, 11 Sep 2012 20:43:17 +0000 (13:43 -0700)]
hwmon: (ad7314) Add 'name' sysfs attribute

commit 3ceefe4319636d89d4bdf40dca9471970f942e4f upstream.

The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.

Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agohpsa: fix handling of protocol error
Stephen M. Cameron [Fri, 14 Sep 2012 21:34:25 +0000 (16:34 -0500)]
hpsa: fix handling of protocol error

commit 256d0eaac87da1e993190846064f339f4c7a63f5 upstream.

If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor.  CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected.  This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not.  Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug.  This bug should not normally cause a problem for direct
attached disk storage.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoDMA: PL330: Check the pointer returned by kzalloc
Sachin Kamat [Mon, 17 Sep 2012 09:50:23 +0000 (15:20 +0530)]
DMA: PL330: Check the pointer returned by kzalloc

commit 61c6e7531d3b66b33187b8cdd700fd8ab93ffd62 upstream.

kzalloc could return NULL. Hence add a check to avoid
NULL pointer dereference.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
[bwh: Backported to 3.2: adjust context and error label]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agohwmon: (ads7871) Add 'name' sysfs attribute
Guenter Roeck [Tue, 11 Sep 2012 20:39:08 +0000 (13:39 -0700)]
hwmon: (ads7871) Add 'name' sysfs attribute

commit 4e21f4eaa49f78d3e977e316514c941053871c76 upstream.

The 'name' sysfs attribute is mandatory for hwmon devices, but was missing
in this driver.

Cc: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Paul Thomas <pthomas8589@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agompt2sas: Fix for issue - Unable to boot from the drive connected to HBA
sreekanth.reddy@lsi.com [Wed, 22 Aug 2012 11:25:13 +0000 (16:55 +0530)]
mpt2sas: Fix for issue - Unable to boot from the drive connected to HBA

commit 10cce6d8b5af0b32bc4254ae4a28423a74c0921c upstream.

This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.

[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agobnx2i: Fixed NULL ptr deference for 1G bnx2 Linux iSCSI offload
Eddie Wai [Tue, 21 Aug 2012 17:35:53 +0000 (10:35 -0700)]
bnx2i: Fixed NULL ptr deference for 1G bnx2 Linux iSCSI offload

commit d6532207116307eb7ecbfa7b9e02c53230096a50 upstream.

This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.

One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets.  When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.

This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.

This change only affects Broadcom's 5709 chipset.

Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
 [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G     ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>]  [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50  EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS:  0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack:  000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
 ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
 0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
 <IRQ>  [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
 [<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
 [<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
 [<ffffffff800125a0>] __do_softirq+0x89/0x133
 [<ffffffff8005e30c>] call_softirq+0x1c/0x28
 [<ffffffff8006d5de>] do_softirq+0x2c/0x7d
 [<ffffffff8006d46e>] do_IRQ+0xee/0xf7
 [<ffffffff8005d625>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
 [<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
 [<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
 [<ffffffff80049560>] cpu_idle+0x95/0xb8
 [<ffffffff80078b1c>] start_secondary+0x479/0x488

Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Wang Xingchao [Wed, 12 Sep 2012 23:43:22 +0000 (07:43 +0800)]
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug

commit b98b60167279df3acac9422c3c9820d9ebbcf9fb upstream.

Clear Audio Enable bit to trigger unsolicated event to notify Audio
Driver part the HDMI hot plug change. The patch fixed the bug when
remove HDMI cable the bit was not cleared correctly.

In intel_hdmi_dpms(), if intel_hdmi->has_audio been true, the "Audio enable bit" will
be set to trigger unsolicated event to notify Alsa driver the change.

intel_hdmi->has_audio will be reset to false from intel_hdmi_detect() after
remove the hdmi cable, here's debug log:

[  187.494153] [drm:output_poll_execute], [CONNECTOR:17:HDMI-A-1] status updated from 1 to 2
[  187.525349] [drm:intel_hdmi_detect], HDMI: has_audio = 0

so when comes back to intel_hdmi_dpms(), the "Audio enable bit" will not be cleared. And this
cause the eld infomation and pin presence doesnot update accordingly in alsa driver side.

This patch will also trigger unsolicated event to alsa driver to notify the hot plug event:

[  187.853159] ALSA sound/pci/hda/patch_hdmi.c:772 HDMI hot plug event: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=1
[  187.853268] ALSA sound/pci/hda/patch_hdmi.c:990 HDMI status: Codec=3 Pin=5 Presence_Detect=0 ELD_Valid=0

Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrm/i915: Reduce a pin-leak BUG into a WARN
Chris Wilson [Sat, 15 Sep 2012 08:41:57 +0000 (09:41 +0100)]
drm/i915: Reduce a pin-leak BUG into a WARN

commit 7e81a42e341a4f15d76624b7c02ffb21b085b56f upstream.

Pin-leaks persist and we get the perennial bug reports of machine
lockups to the BUG_ON(pin_count==MAX). If we instead loudly report that
the object cannot be pinned at that time it should prevent the driver from
locking up, and hopefully restore a semblance of working whilst still
leaving us a OOPS to debug.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoARM: 7532/1: decompressor: reset SCTLR.TRE for VMSA ARMv7 cores
Matthew Leach [Tue, 11 Sep 2012 16:56:57 +0000 (17:56 +0100)]
ARM: 7532/1: decompressor: reset SCTLR.TRE for VMSA ARMv7 cores

commit e1e5b7e4251c7538ca08c2c5545b0c2fbd8a6635 upstream.

This patch zeroes the SCTLR.TRE bit prior to setting the mapping as
cacheable for ARMv7 cores in the decompressor, ensuring that the
memory region attributes are obtained from the C and B bits, not from
the page tables.

Cc: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodmaengine: at_hdmac: check that each sg data length is non-null
Nicolas Ferre [Tue, 11 Sep 2012 15:21:45 +0000 (17:21 +0200)]
dmaengine: at_hdmac: check that each sg data length is non-null

commit c456797681db814f4f5b36909e8e94047bf53d9c upstream.

Avoid the construction of a malformed DMA request sent to
the DMA controller.
Log message is for debug only because this condition is unlikely to
append and may only trigger at driver development time.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodmaengine: at_hdmac: fix comment in atc_prep_slave_sg()
Nicolas Ferre [Tue, 11 Sep 2012 15:21:44 +0000 (17:21 +0200)]
dmaengine: at_hdmac: fix comment in atc_prep_slave_sg()

commit c618a9be0e8c0f36baee2560860a0118a428fb26 upstream.

s/dma_memcpy/slave_sg/ and it is sg length that we are
talking about.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agobrcmfmac: Fix big endian host configuration data.
Hante Meuleman [Tue, 11 Sep 2012 19:16:48 +0000 (21:16 +0200)]
brcmfmac: Fix big endian host configuration data.

commit e020a83d0942a5aceac35986500c9834efc8707d upstream.

Fixes big endian host configuration parameters.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agobrcmfmac: fix big endian bug in i-scan.
Hante Meuleman [Tue, 11 Sep 2012 19:16:47 +0000 (21:16 +0200)]
brcmfmac: fix big endian bug in i-scan.

commit ed205b361956c96e0d8c09a8c9135a6a79cd9541 upstream.

ssid len is 32 bit and needs endian conversion for big endian systems.

Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agortlwifi: rtl8192ce: Log message that B_CUT device may not work
Larry Finger [Tue, 11 Sep 2012 16:11:13 +0000 (11:11 -0500)]
rtlwifi: rtl8192ce: Log message that B_CUT device may not work

commit 022e1d0680c7b4366017393417b8758be5abcee8 upstream.

There are a number of problems that occur for the latest version
of the Realtek RTL8188CE device with the in-kernel driver. These
include selection of the wrong firmware, and system lockup. A full
fix is known, but is too invasive for inclusion in stable. This patch
fixes the problem with loading the wrong firmware, and logs a message
that the device may not work for kernels 3.6 and older.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Tested-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agohpwdt: Fix kdump issue in hpwdt
Toshi Kani [Mon, 27 Aug 2012 18:52:24 +0000 (12:52 -0600)]
hpwdt: Fix kdump issue in hpwdt

commit 308b135e4fcc00c80c07e0e04e7afa8edf78583c upstream.

kdump can be interrupted by watchdog timer when the timer is left
activated on the crash kernel. Changed the hpwdt driver to disable
watchdog timer at boot-time. This assures that watchdog timer is
disabled until /dev/watchdog is opened, and prevents watchdog timer
to be left running on the crash kernel.

Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Thomas Mingarelli <Thomas.Mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agosched: Fix ancient race in do_exit()
Yasunori Goto [Tue, 17 Jan 2012 08:40:31 +0000 (17:40 +0900)]
sched: Fix ancient race in do_exit()

commit b5740f4b2cb3503b436925eb2242bc3d75cd3dfe upstream.

try_to_wake_up() has a problem which may change status from TASK_DEAD to
TASK_RUNNING in race condition with SMI or guest environment of virtual
machine. As a result, exited task is scheduled() again and panic occurs.

Here is the sequence how it occurs:

 ----------------------------------+-----------------------------
                                   |
            CPU A                  |             CPU B
 ----------------------------------+-----------------------------

TASK A calls exit()....

do_exit()

  exit_mm()
    down_read(mm->mmap_sem);

    rwsem_down_failed_common()

      set TASK_UNINTERRUPTIBLE
      set waiter.task <= task A
      list_add to sem->wait_list
           :
      raw_spin_unlock_irq()
      (I/O interruption occured)

                                      __rwsem_do_wake(mmap_sem)

                                        list_del(&waiter->list);
                                        waiter->task = NULL
                                        wake_up_process(task A)
                                          try_to_wake_up()
                                             (task is still
                                               TASK_UNINTERRUPTIBLE)
                                              p->on_rq is still 1.)

                                              ttwu_do_wakeup()
                                                 (*A)
                                                   :
     (I/O interruption handler finished)

      if (!waiter.task)
          schedule() is not called
          due to waiter.task is NULL.

      tsk->state = TASK_RUNNING

          :
                                              check_preempt_curr();
                                                  :
  task->state = TASK_DEAD
                                              (*B)
                                        <---    set TASK_RUNNING (*C)

     schedule()
     (exit task is running again)
     BUG_ON() is called!
 --------------------------------------------------------

The execution time between (*A) and (*B) is usually very short,
because the interruption is disabled, and setting TASK_RUNNING at (*C)
must be executed before setting TASK_DEAD.

HOWEVER, if SMI is interrupted between (*A) and (*B),
(*C) is able to execute AFTER setting TASK_DEAD!
Then, exited task is scheduled again, and BUG_ON() is called....

If the system works on guest system of virtual machine, the time
between (*A) and (*B) may be also long due to scheduling of hypervisor,
and same phenomenon can occur.

By this patch, do_exit() waits for releasing task->pi_lock which is used
in try_to_wake_up(). It guarantees the task becomes TASK_DEAD after
waking up.

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20120117174031.3118.E1E9C6FF@jp.fujitsu.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agocpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU
Tejun Heo [Tue, 18 Sep 2012 21:24:59 +0000 (14:24 -0700)]
cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU

commit 6889125b8b4e09c5e53e6ecab3433bed1ce198c9 upstream.

powernowk8_target() runs off a per-cpu work item and if the
cpufreq_policy->cpu is different from the current one, it migrates the
kworker to the target CPU by manipulating current->cpus_allowed.  The
function migrates the kworker back to the original CPU but this is
still broken.  Workqueue concurrency management requires the kworkers
to stay on the same CPU and powernowk8_target() ends up triggerring
BUG_ON(rq != this_rq()) in try_to_wake_up_local() if it contends on
fidvid_mutex and sleeps.

It is unclear why this bug is being reported now.  Duncan says it
appeared to be a regression of 3.6-rc1 and couldn't reproduce it on
3.5.  Bisection seemed to point to 63d95a91 "workqueue: use @pool
instead of @gcwq or @cpu where applicable" which is an non-functional
change.  Given that the reproduce case sometimes took upto days to
trigger, it's easy to be misled while bisecting.  Maybe something made
contention on fidvid_mutex more likely?  I don't know.

This patch fixes the bug by using work_on_cpu() instead if @pol->cpu
isn't the same as the current one.  The code assumes that
cpufreq_policy->cpu is kept online by the caller, which Rafael tells
me is the case.

stable: ed48ece27c ("workqueue: reimplement work_on_cpu() using
        system_wq") should be applied before this; otherwise, the
        behavior could be horrible.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47301
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoworkqueue: reimplement work_on_cpu() using system_wq
Tejun Heo [Tue, 18 Sep 2012 19:48:43 +0000 (12:48 -0700)]
workqueue: reimplement work_on_cpu() using system_wq

commit ed48ece27cd3d5ee0354c32bbaec0f3e1d4715c3 upstream.

The existing work_on_cpu() implementation is hugely inefficient.  It
creates a new kthread, execute that single function and then let the
kthread die on each invocation.

Now that system_wq can handle concurrent executions, there's no
advantage of doing this.  Reimplement work_on_cpu() using system_wq
which makes it simpler and way more efficient.

stable: While this isn't a fix in itself, it's needed to fix a
        workqueue related bug in cpufreq/powernow-k8.  AFAICS, this
        shouldn't break other existing users.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agovfs: dcache: use DCACHE_DENTRY_KILLED instead of DCACHE_DISCONNECTED in d_kill()
Miklos Szeredi [Mon, 17 Sep 2012 20:31:38 +0000 (22:31 +0200)]
vfs: dcache: use DCACHE_DENTRY_KILLED instead of DCACHE_DISCONNECTED in d_kill()

commit b161dfa6937ae46d50adce8a7c6b12233e96e7bd upstream.

IBM reported a soft lockup after applying the fix for the rename_lock
deadlock.  Commit c83ce989cb5f ("VFS: Fix the nfs sillyrename regression
in kernel 2.6.38") was found to be the culprit.

The nfs sillyrename fix used DCACHE_DISCONNECTED to indicate that the
dentry was killed.  This flag can be set on non-killed dentries too,
which results in infinite retries when trying to traverse the dentry
tree.

This patch introduces a separate flag: DCACHE_DENTRY_KILLED, which is
only set in d_kill() and makes try_to_ascend() test only this flag.

IBM reported successful test results with this patch.

Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agocciss: fix handling of protocol error
Stephen M. Cameron [Fri, 14 Sep 2012 21:35:10 +0000 (16:35 -0500)]
cciss: fix handling of protocol error

commit 2453f5f992717251cfadab6184fbb3ec2f2e8b40 upstream.

If a command completes with a status of CMD_PROTOCOL_ERR, this
information should be conveyed to the SCSI mid layer, not dropped
on the floor.  Unlike a similar bug in the hpsa driver, this bug
only affects tape drives and CD and DVD ROM drives in the cciss
driver, and to induce it, you have to disconnect (or damage) a
cable, so it is not a very likely scenario (which would explain
why the bug has gone undetected for the last 10 years.)

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agomemory hotplug: fix section info double registration bug
qiuxishi [Mon, 17 Sep 2012 21:09:24 +0000 (14:09 -0700)]
memory hotplug: fix section info double registration bug

commit f14851af0ebb32745c6c5a2e400aa0549f9d20df upstream.

There may be a bug when registering section info.  For example, on my
Itanium platform, the pfn range of node0 includes the other nodes, so
other nodes' section info will be double registered, and memmap's page
count will equal to 3.

  node0: start_pfn=0x100,    spanned_pfn=0x20fb00, present_pfn=0x7f8a3, => 0x000100-0x20fc00
  node1: start_pfn=0x80000,  spanned_pfn=0x80000,  present_pfn=0x80000, => 0x080000-0x100000
  node2: start_pfn=0x100000, spanned_pfn=0x80000,  present_pfn=0x80000, => 0x100000-0x180000
  node3: start_pfn=0x180000, spanned_pfn=0x80000,  present_pfn=0x80000, => 0x180000-0x200000

  free_all_bootmem_node()
register_page_bootmem_info_node()
register_page_bootmem_info_section()

When hot remove memory, we can't free the memmap's page because
page_count() is 2 after put_page_bootmem().

  sparse_remove_one_section()
free_section_usemap()
free_map_bootmem()
put_page_bootmem()

[akpm@linux-foundation.org: add code comment]
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agomm/page_alloc: fix the page address of higher page's buddy calculation
Li Haifeng [Mon, 17 Sep 2012 21:09:21 +0000 (14:09 -0700)]
mm/page_alloc: fix the page address of higher page's buddy calculation

commit 0ba8f2d59304dfe69b59c034de723ad80f7ab9ac upstream.

The heuristic method for buddy has been introduced since commit
43506fad21ca ("mm/page_alloc.c: simplify calculation of combined index
of adjacent buddy lists").  But the page address of higher page's buddy
was wrongly calculated, which will lead page_is_buddy to fail for ever.
IOW, the heuristic method would be disabled with the wrong page address
of higher page's buddy.

Calculating the page address of higher page's buddy should be based
higher_page with the offset between index of higher page and index of
higher page's buddy.

Signed-off-by: Haifeng Li <omycle@gmail.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: KyongHo Cho <pullip.cho@samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrivers/rtc/rtc-twl.c: ensure all interrupts are disabled during probe
Kevin Hilman [Mon, 17 Sep 2012 21:09:17 +0000 (14:09 -0700)]
drivers/rtc/rtc-twl.c: ensure all interrupts are disabled during probe

commit 8dcebaa9a0ae8a0487f4342f3d56d2cb1c980860 upstream.

On some platforms, bootloaders are known to do some interesting RTC
programming.  Without going into the obscurities as to why this may be
the case, suffice it to say the the driver should not make any
assumptions about the state of the RTC when the driver loads.  In
particular, the driver probe should be sure that all interrupts are
disabled until otherwise programmed.

This was discovered when finding bursty I2C traffic every second on
Overo platforms.  This I2C overhead was keeping the SoC from hitting
deep power states.  The cause was found to be the RTC firing every
second on the I2C-connected TWL PMIC.

Special thanks to Felipe Balbi for suggesting to look for a rogue driver
as the source of the I2C traffic rather than the I2C driver itself.

Special thanks to Steve Sakoman for helping track down the source of the
continuous RTC interrups on the Overo boards.

Signed-off-by: Kevin Hilman <khilman@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Tested-by: Steve Sakoman <steve@sakoman.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Tested-by: Shubhrajyoti Datta <omaplinuxkernel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agonbd: clear waiting_queue on shutdown
Paul Clements [Mon, 17 Sep 2012 21:09:02 +0000 (14:09 -0700)]
nbd: clear waiting_queue on shutdown

commit fded4e090c60100d709318896c79816d68d5b47d upstream.

Fix a serious but uncommon bug in nbd which occurs when there is heavy
I/O going to the nbd device while, at the same time, a failure (server,
network) or manual disconnect of the nbd connection occurs.

There is a small window between the time that the nbd_thread is stopped
and the socket is shutdown where requests can continue to be queued to
nbd's internal waiting_queue.  When this happens, those requests are
never completed or freed.

The fix is to clear the waiting_queue on shutdown of the nbd device, in
the same way that the nbd request queue (queue_head) is already being
cleared.

Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2: local nbd_device pointers are called 'lo' not 'nbd']
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agomm/ia64: fix a memory block size bug
Jianguo Wu [Mon, 17 Sep 2012 21:08:56 +0000 (14:08 -0700)]
mm/ia64: fix a memory block size bug

commit 05cf96398e1b6502f9e191291b715c7463c9d5dd upstream.

I found following definition in include/linux/memory.h, in my IA64
platform, SECTION_SIZE_BITS is equal to 32, and MIN_MEMORY_BLOCK_SIZE
will be 0.

  #define MIN_MEMORY_BLOCK_SIZE     (1 << SECTION_SIZE_BITS)

Because MIN_MEMORY_BLOCK_SIZE is int type and length of 32bits,
so MIN_MEMORY_BLOCK_SIZE(1 << 32) will will equal to 0.
Actually when SECTION_SIZE_BITS >= 31, MIN_MEMORY_BLOCK_SIZE will be wrong.
This will cause wrong system memory infomation in sysfs.
I think it should be:

  #define MIN_MEMORY_BLOCK_SIZE     (1UL << SECTION_SIZE_BITS)

And "echo offline > memory0/state" will cause following call trace:

  kernel BUG at mm/memory_hotplug.c:885!
  sh[6455]: bugcheck! 0 [1]
  Pid: 6455, CPU 0, comm:                   sh
  psr : 0000101008526030 ifs : 8000000000000fa4 ip  : [<a0000001008c40f0>]    Not tainted (3.6.0-rc1)
  ip is at offline_pages+0x210/0xee0
  Call Trace:
    show_stack+0x80/0xa0
    show_regs+0x640/0x920
    die+0x190/0x2c0
    die_if_kernel+0x50/0x80
    ia64_bad_break+0x3d0/0x6e0
    ia64_native_leave_kernel+0x0/0x270
    offline_pages+0x210/0xee0
    alloc_pages_current+0x180/0x2a0

Signed-off-by: Jianguo Wu <wujianguo@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agofs/proc: fix potential unregister_sysctl_table hang
Francesco Ruggeri [Thu, 13 Sep 2012 22:03:37 +0000 (15:03 -0700)]
fs/proc: fix potential unregister_sysctl_table hang

commit 6bf6104573482570f7103d3e5ddf9574db43a363 upstream.

The unregister_sysctl_table() function hangs if all references to its
ctl_table_header structure are not dropped.

This can happen sometimes because of a leak in proc_sys_lookup():
proc_sys_lookup() gets a reference to the table via lookup_entry(), but
it does not release it when a subsequent call to sysctl_follow_link()
fails.

This patch fixes this leak by making sure the reference is always
dropped on return.

See also commit 076c3eed2c31 ("sysctl: Rewrite proc_sys_lookup
introducing find_entry and lookup_entry") which reorganized this code in
3.4.

Tested in Linux 3.4.4.

Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoASoC: samsung dma - Don't indicate support for pause/resume.
Dylan Reid [Sat, 1 Sep 2012 08:38:19 +0000 (01:38 -0700)]
ASoC: samsung dma - Don't indicate support for pause/resume.

commit 57b2d68863f281737d8596cb3d76d89d9cc54fd8 upstream.

The pause and resume operations indicate that the stream can be
un-paused/resumed from the exact location they were paused/suspended.
This is not true for this driver, the pause and suspend triggers share
the same code path with stop, they flush all pending DMA transfers.
This drops all pending samples.  The pause_release/resume triggers are
the same as start, except that prepare won't be called beforehand,
nothing will be enqueued to the DMA engine and nothing will happen (no
audio).  Removing the pause flag will let apps know that it isn't
supported.  Removing the resume flag will cause user space to call
prepare and start instead of resume, so audio will continue playing when
the system wakes up.

Before removing the pause and resume flags, I tested this on an exynos
5250, using 'aplay -i'. Pause/un-pause leads to silence followed by a
write error.  Suspend/resume testing led to the same result.  Removing
the two flags fixes suspend/resume (since snd_pcm_prepare is called
again). And leads to a proper reporting of pause not supported.

Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agotarget: Fix ->data_length re-assignment bug with SCSI overflow
Nicholas Bellinger [Thu, 16 Aug 2012 22:33:10 +0000 (15:33 -0700)]
target: Fix ->data_length re-assignment bug with SCSI overflow

commit 4c054ba63ad47ef244cfcfa1cea38134620a5bae upstream.

This patch fixes a long-standing bug with SCSI overflow handling
where se_cmd->data_length was incorrectly being re-assigned to
the larger CDB extracted allocation length, resulting in a number
of fabric level errors that would end up causing a session reset
in most cases.  So instead now:

 - Only re-assign se_cmd->data_length durining UNDERFLOW (to use the
   smaller value)
 - Use existing se_cmd->data_length for OVERFLOW (to use the smaller
   value)

This fix has been tested with the following CDB to generate an
SCSI overflow:

  sg_raw -r512 /dev/sdc 28 0 0 0 0 0 0 0 9 0

Tested using iscsi-target, tcm_qla2xxx, loopback and tcm_vhost fabric
ports.  Here is a bit more detail on each case:

 - iscsi-target: Bug with open-iscsi with overflow, sg_raw returns
                 -3584 bytes of data.
 - tcm_qla2xxx: Working as expected, returnins 512 bytes of data
 - loopback: sg_raw returns CHECK_CONDITION, from overflow rejection
             in transport_generic_map_mem_to_cmd()
 - tcm_vhost: Same as loopback

Reported-by: Roland Dreier <roland@purestorage.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoLinux 3.2.30 v3.2.30
Ben Hutchings [Wed, 19 Sep 2012 14:05:26 +0000 (15:05 +0100)]
Linux 3.2.30

9 years agovfs: make O_PATH file descriptors usable for 'fstat()'
Linus Torvalds [Fri, 14 Sep 2012 21:48:21 +0000 (14:48 -0700)]
vfs: make O_PATH file descriptors usable for 'fstat()'

commit 55815f70147dcfa3ead5738fd56d3574e2e3c1c2 upstream.

We already use them for openat() and friends, but fstat() also wants to
be able to use O_PATH file descriptors.  This should make it more
directly comparable to the O_SEARCH of Solaris.

Note that you could already do the same thing with "fstatat()" and an
empty path, but just doing "fstat()" directly is simpler and faster, so
there is no reason not to just allow it directly.

See also commit 332a2e1244bd, which did the same thing for fchdir, for
the same reasons.

Reported-by: ольга крыжановская <olga.kryzhanovska@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoVFS: make vfs_fstat() use f[get|put]_light()
Linus Torvalds [Sat, 28 Apr 2012 21:55:17 +0000 (14:55 -0700)]
VFS: make vfs_fstat() use f[get|put]_light()

commit e994defb7b6813ba6fa7a2a36e86d2455ad1dc35 upstream.

Use the *_light() versions that properly avoid doing the file user count
updates when they are unnecessary.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoeCryptfs: Copy up attributes of the lower target inode after rename
Tyler Hicks [Thu, 13 Sep 2012 19:00:56 +0000 (12:00 -0700)]
eCryptfs: Copy up attributes of the lower target inode after rename

commit 8335eafc2859e1a26282bef7c3d19f3d68868b8a upstream.

After calling into the lower filesystem to do a rename, the lower target
inode's attributes were not copied up to the eCryptfs target inode. This
resulted in the eCryptfs target inode staying around, rather than being
evicted, because i_nlink was not updated for the eCryptfs inode. This
also meant that eCryptfs didn't do the final iput() on the lower target
inode so it stayed around, as well. This would result in a failure to
free up space occupied by the target file in the rename() operation.
Both target inodes would eventually be evicted when the eCryptfs
filesystem was unmounted.

This patch calls fsstack_copy_attr_all() after the lower filesystem
does its ->rename() so that important inode attributes, such as i_nlink,
are updated at the eCryptfs layer. ecryptfs_evict_inode() is now called
and eCryptfs can drop its final reference on the lower inode.

http://launchpad.net/bugs/561129

Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrm/nouveau: fix booting with plymouth + dumb support
Dave Airlie [Fri, 14 Sep 2012 03:28:23 +0000 (13:28 +1000)]
drm/nouveau: fix booting with plymouth + dumb support

commit 610bd7da160f76f1644ecb4cd7f39511b49a22cc upstream.

We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.

Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrm/radeon: rework pll selection (v3)
Alex Deucher [Fri, 31 Aug 2012 15:56:50 +0000 (11:56 -0400)]
drm/radeon: rework pll selection (v3)

commit 985f61f7ee647ad570c05eab0b74915da2ac8e19 upstream.

For DP we can use the same PPLL for all active DP
encoders.  Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work.  Also clean up the code
a bit.

v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
    - document functions
    - break in main encoder search loop after matching.
      no need to keep checking additional encoders.

fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrm/radeon: fix ordering in pll picking on dce4+
Alex Deucher [Mon, 6 Aug 2012 21:06:03 +0000 (17:06 -0400)]
drm/radeon: fix ordering in pll picking on dce4+

commit ecd67955fd4c8e66e4df312098989d5fa7da624c upstream.

No functional change, but re-order the cases so they
evaluate properly due to the way the DCE macros work.

Noticed by kallisti5 on IRC.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agodrm/radeon: fix up pll selection on DCE5/6
Alex Deucher [Tue, 17 Jul 2012 18:02:43 +0000 (14:02 -0400)]
drm/radeon: fix up pll selection on DCE5/6

commit 26fe45a0a76f165425f332a5aaa298f149f9db22 upstream.

Selecting ATOM_PPLL_INVALID should be equivalent as the
DCPLL or PPLL0 are already programmed for the DISPCLK, but
the preferred method is to always specify the PLL selected.
SetPixelClock will check the parameters and skip the
programming if the PLL is already set up.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
[bwh: Backported to 3.2: drop the DCE6 case]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoahci: Add alternate identifier for the 88SE9172
Alan Cox [Tue, 4 Sep 2012 15:07:18 +0000 (16:07 +0100)]
ahci: Add alternate identifier for the 88SE9172

commit 17c60c6b763cb5b83b0185e7d38d01d18e55a05a upstream.

This can also appear as 0x9192. Reported in bugzilla and confirmed with the
board documentation for these boards.

Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42970
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agovmwgfx: add dumb ioctl support
Dave Airlie [Tue, 28 Aug 2012 01:53:54 +0000 (01:53 +0000)]
vmwgfx: add dumb ioctl support

commit 5e1782d224c79b26ab7d5c31e3f87657000714fb upstream.

Testing and works with the -modesetting driver,

Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoALSA: ice1724: Use linear scale for AK4396 volume control.
Matteo Frigo [Wed, 12 Sep 2012 14:12:06 +0000 (10:12 -0400)]
ALSA: ice1724: Use linear scale for AK4396 volume control.

commit 3737e2be505d872bf2b3c1cd4151b2d2b413d7b5 upstream.

The AK4396 DAC has a linear-scale attentuator, but
sound/pci/ice1712/prodigy_hifi.c used a log scale instead, which is
not quite right.  This patch restores the correct scale, borrowing
from the ak4396 code in sound/pci/oxygen/oxygen.c.

Signed-off-by: Matteo Frigo <athena@fftw.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agohwmon: (twl4030-madc-hwmon) Initialize uninitialized structure elements
Guenter Roeck [Tue, 19 Jun 2012 15:00:00 +0000 (08:00 -0700)]
hwmon: (twl4030-madc-hwmon) Initialize uninitialized structure elements

commit 73d7c119255615a26070f9d6cdb722a166a29015 upstream.

twl4030_madc_conversion uses do_avg and type structure elements of
twl4030_madc_request. Initialize structure to avoid random operation.

Fix for: Coverity CID 200794 Uninitialized scalar variable.

Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoEHCI: Update qTD next pointer in QH overlay region during unlink
Pavankumar Kondeti [Fri, 7 Sep 2012 05:53:28 +0000 (11:23 +0530)]
EHCI: Update qTD next pointer in QH overlay region during unlink

commit 3d037774b42ed677f699b1dce7d548d55f4e4c2b upstream.

There is a possibility of QH overlay region having reference to a stale
qTD pointer during unlink.

Consider an endpoint having two pending qTD before unlink process begins.
The endpoint's QH queue looks like this.

qTD1 --> qTD2 --> Dummy

To unlink qTD2, QH is removed from asynchronous list and Asynchronous
Advance Doorbell is programmed.  The qTD1's next qTD pointer is set to
qTD2'2 next qTD pointer and qTD2 is retired upon controller's doorbell
interrupt.  If QH's current qTD pointer points to qTD1, transfer overlay
region still have reference to qTD2. But qtD2 is just unlinked and freed.
This may cause EHCI system error.  Fix this by updating qTD next pointer
in QH overlay region with the qTD next pointer of the current qTD.

Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agostaging: r8712u: fix bug in r8712_recv_indicatepkt()
Eric Dumazet [Mon, 10 Sep 2012 19:22:11 +0000 (21:22 +0200)]
staging: r8712u: fix bug in r8712_recv_indicatepkt()

commit abf02cfc179bb4bd30d05f582d61b3b8f429b813 upstream.

64bit arches have a buggy r8712u driver, let's fix it.

skb->tail must be set properly or network stack behavior is undefined.

Addresses https://bugzilla.redhat.com/show_bug.cgi?id=847525
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=45071

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Jones <davej@redhat.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoUSB: ftdi_sio: do not claim CDC ACM function
Bjørn Mork [Mon, 10 Sep 2012 10:01:05 +0000 (12:01 +0200)]
USB: ftdi_sio: do not claim CDC ACM function

commit f08dea734844aa42ec57c229b0b73b3d7d21f810 upstream.

The Microchip vid:pid 04d8:000a is used for their CDC ACM
demo firmware application.  This is a device with a single
function conforming to the CDC ACM specification and with
the intention of demonstrating CDC ACM class firmware and
driver interaction.  The demo is used on a number of
development boards, and may also be used unmodified by
vendors using Microchip hardware.

Some vendors have re-used this vid:pid for other types of
firmware, emulating FTDI chips. Attempting to continue to
support such devices without breaking class based
applications that by matching on interface
class/subclass/proto being ff/ff/00.  I have no information
about the actual device or interface descriptors, but this
will at least make the proper CDC ACM devices work again.
Anyone having details of the offending device's descriptors
should update this entry with the details.

Reported-by: Florian Wöhrl <fw@woehrl.biz>
Reported-by: Xiaofan Chen <xiaofanc@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoALSA: hda - Fix Oops at codec reset/reconfig
Takashi Iwai [Mon, 10 Sep 2012 07:39:31 +0000 (09:39 +0200)]
ALSA: hda - Fix Oops at codec reset/reconfig

commit 07dc59f0988cb54fd87bd373b3b27eb2401dd811 upstream.

snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec.  However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.

This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.

Reported-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path
Will Deacon [Fri, 7 Sep 2012 17:21:44 +0000 (18:21 +0100)]
ARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path

commit 2b2040af0b64cd93e5d4df2494c4486cf604090d upstream.

get_user may fail to load from the provided __user address due to an
unhandled fault generated by the access.

In the case of the undefined instruction trap, this results in failure
to load the faulting instruction, in which case we should send SIGILL to
the task rather than continue with potentially uninitialised data.

Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoARM: 7513/1: Make sure dtc is built before running it
David Brown [Tue, 4 Sep 2012 20:36:37 +0000 (21:36 +0100)]
ARM: 7513/1: Make sure dtc is built before running it

commit 70b0476a2394de4f4e32e0b67288d80ff71ca963 upstream.

'make dtbs' in a clean tree will try running the dtc before actually
building it.  Make these rules depend upon the scripts to build it.

Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoSUNRPC: Fix a UDP transport regression
Trond Myklebust [Fri, 7 Sep 2012 15:08:50 +0000 (11:08 -0400)]
SUNRPC: Fix a UDP transport regression

commit f39c1bfb5a03e2d255451bff05be0d7255298fa4 upstream.

Commit 43cedbf0e8dfb9c5610eb7985d5f21263e313802 (SUNRPC: Ensure that
we grab the XPRT_LOCK before calling xprt_alloc_slot) is causing
hangs in the case of NFS over UDP mounts.

Since neither the UDP or the RDMA transport mechanism use dynamic slot
allocation, we can skip grabbing the socket lock for those transports.
Add a new rpc_xprt_op to allow switching between the TCP and UDP/RDMA
case.

Note that the NFSv4.1 back channel assigns the slot directly
through rpc_run_bc_task, so we can ignore that case.

Reported-by: Dick Streefland <dick.streefland@altium.nl>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoNFS: return error from decode_getfh in decode open
Weston Andros Adamson [Thu, 6 Sep 2012 19:54:27 +0000 (15:54 -0400)]
NFS: return error from decode_getfh in decode open

commit 01913b49cf1dc6409a07dd2a4cc6af2e77f3c410 upstream.

If decode_getfh failed, nfs4_xdr_dec_open would return 0 since the last
decode_* call must have succeeded.

Signed-off-by: Weston Andros Adamson <dros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agokobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"
Bjørn Mork [Sun, 2 Sep 2012 13:41:34 +0000 (15:41 +0200)]
kobject: fix oops with "input0: bad kobj_uevent_env content in show_uevent()"

commit 60e233a56609fd963c59e99bd75c663d63fa91b6 upstream.

Fengguang Wu <fengguang.wu@intel.com> writes:

> After the __devinit* removal series, I can still get kernel panic in
> show_uevent(). So there are more sources of bug..
>
> Debug patch:
>
> @@ -343,8 +343,11 @@ static ssize_t show_uevent(struct device
>                 goto out;
>
>         /* copy keys to file */
> -       for (i = 0; i < env->envp_idx; i++)
> +       dev_err(dev, "uevent %d env[%d]: %s/.../%s\n", env->buflen, env->envp_idx, top_kobj->name, dev->kobj.name);
> +       for (i = 0; i < env->envp_idx; i++) {
> +               printk(KERN_ERR "uevent %d env[%d]: %s\n", (int)count, i, env->envp[i]);
>                 count += sprintf(&buf[count], "%s\n", env->envp[i]);
> +       }
>
> Oops message, the env[] is again not properly initilized:
>
> [   44.068623] input input0: uevent 61 env[805306368]: input0/.../input0
> [   44.069552] uevent 0 env[0]: (null)

This is a completely different CONFIG_HOTPLUG problem, only
demonstrating another reason why CONFIG_HOTPLUG should go away.  I had a
hard time trying to disable it anyway ;-)

The problem this time is lots of code assuming that a call to
add_uevent_var() will guarantee that env->buflen > 0.  This is not true
if CONFIG_HOTPLUG is unset.  So things like this end up overwriting
env->envp_idx because the array index is -1:

if (add_uevent_var(env, "MODALIAS="))
return -ENOMEM;
        len = input_print_modalias(&env->buf[env->buflen - 1],
   sizeof(env->buf) - env->buflen,
   dev, 0);

Don't know what the best action is, given that there seem to be a *lot*
of this around the kernel.  This patch "fixes" the problem for me, but I
don't know if it can be considered an appropriate fix.

[ It is the correct fix for now, for 3.7 forcing CONFIG_HOTPLUG to
always be on is the longterm fix, but it's too late for 3.6 and older
kernels to resolve this that way - gregkh ]

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoUSB: add device quirk for Joss Optical touchboard
Alan Stern [Tue, 4 Sep 2012 14:41:02 +0000 (10:41 -0400)]
USB: add device quirk for Joss Optical touchboard

commit 92fc7a8b0f20bdb243c706daf42658e8e0cd2ef0 upstream.

This patch (as1604) adds a CONFIG_INTF_STRINGS quirk for the Joss
infrared touchboard device.  The device doesn't like to be asked for
its interface strings.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: adam ? <adam3337@wp.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoUSB: ftdi_sio: PID for NZR SEM 16+ USB
Horst Schirmeier [Thu, 30 Aug 2012 22:00:28 +0000 (00:00 +0200)]
USB: ftdi_sio: PID for NZR SEM 16+ USB

commit 26a538b9ea2a3ee10dafc0068f0560dfd7b7ba37 upstream.

This adds the USB PID for the NZR SEM 16+ USB energy monitor device
<http://www.nzr.de>.  It works perfectly with the GPL software on
<http://schou.dk/linux/sparometer/>.

Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoUSB: ftdi-sio: add support for more Physik Instrumente devices
Éric Piel [Tue, 4 Sep 2012 15:25:06 +0000 (17:25 +0200)]
USB: ftdi-sio: add support for more Physik Instrumente devices

commit dafc4f7be1a556ca3868d343c00127728b397068 upstream.

Commit b69cc672052540 added support for the E-861.  After acquiring a C-867, I
realised that every Physik Instrumente's device has a different PID. They are
listed in the Windows device driver's .inf file. So here are all PIDs for the
current (and probably future) USB devices from Physik Instrumente.

Compiled, but only actually tested on the E-861 and C-867.

Signed-off-by: Éric Piel <piel@delmic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoibmveth: Fix alignment of rx queue bug
Santiago Leon [Tue, 4 Sep 2012 14:41:37 +0000 (14:41 +0000)]
ibmveth: Fix alignment of rx queue bug

commit d90c92fee89ccd75ef2646f3bde0b4c0450666c3 upstream.

This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.

The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.

The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.

Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agotty: serial: imx: don't reinit clock in imx_setup_ufcr()
Dirk Behme [Fri, 31 Aug 2012 08:02:47 +0000 (10:02 +0200)]
tty: serial: imx: don't reinit clock in imx_setup_ufcr()

commit 7be0670f7b9198382938a03ff3db7f47ef6b4780 upstream.

Remove the clock configuration from imx_setup_ufcr(). This
isn't needed here and will cause garbage output if done.

To be be sure that we only touch the bits we want (TXTL and RXTL)
we have to mask out all other bits of the UFCR register. Add
one non-existing bit macro for this, too (bit 6, DCEDTE on i.MX6).

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Shawn Guo <shawn.guo@linaro.org>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Xinyu Chen <xinyu.chen@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: deleted code in imx_setup_ufcr() refers to
 sport->clk not sport->clk_per]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agotty: serial: imx: console write routing is unsafe on SMP
Xinyu Chen [Mon, 27 Aug 2012 07:36:51 +0000 (09:36 +0200)]
tty: serial: imx: console write routing is unsafe on SMP

commit 9ec1882df244c4ee1baa692676fef5e8b0f5487d upstream.

The console feature's write routing is unsafe on SMP with
the startup/shutdown call.

There could be several consumers of the console
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which open /dev/console and write with sys_write()

The shell goes into the normal uart open/write routing,
but the other two go into the console operations.
The open routing calls imx serial startup, which will write USR1/2
register without any lock and critical with imx_console_write call.

Add a spin_lock for startup/shutdown/console_write routing.

This patch is a port from Freescale's Android kernel.

Signed-off-by: Xinyu Chen <xinyu.chen@freescale.com>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agousb: host: xhci: fix compilation error for non-PCI based stacks
Moiz Sonasath [Wed, 5 Sep 2012 05:34:26 +0000 (08:34 +0300)]
usb: host: xhci: fix compilation error for non-PCI based stacks

commit 296365781903226a3fb8758901eaeec09d2798e4 upstream.

For non PCI-based stacks, this function call
usb_disable_xhci_ports(to_pci_dev(hcd->self.controller));
made from xhci_shutdown is not applicable.

Ideally, we wouldn't have any PCI-specific code on
a generic driver such as the xHCI stack, but it looks
like we should just stub usb_disable_xhci_ports() out
for non-PCI devices.

[ balbi@ti.com: slight improvement to commit log ]

This patch should be backported to kernels as old as 3.0, since the
commit it fixes (e95829f474f0db3a4d940cae1423783edd966027 "xhci: Switch
PPT ports to EHCI on shutdown.") was marked for stable.

Signed-off-by: Moiz Sonasath<m-sonasath@ti.com>
Signed-off-by: Ruchika Kharwar <ruchika@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agousb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware
Alexis R. Cortes [Fri, 3 Aug 2012 19:00:27 +0000 (14:00 -0500)]
usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware

commit 71c731a296f1b08a3724bd1b514b64f1bda87a23 upstream.

This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.

If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.

As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.

For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.

If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.

Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).

This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.

This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset.  The kernels will need to
contain both commit 10d674a82e553cb8a1f41027bb3c3e309b3f6804 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd37df08aaa599aa361a9f8b836ba98e554 "usb: Add support for root hub
port status CAS".  The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.

Signed-off-by: Alexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoxhci: Make handover code more robust
Matthew Garrett [Tue, 14 Aug 2012 20:44:49 +0000 (16:44 -0400)]
xhci: Make handover code more robust

commit e955a1cd086de4d165ae0f4c7be7289d84b63bdc upstream.

My test platform (Intel DX79SI) boots reliably under BIOS, but frequently
crashes when booting via UEFI. I finally tracked this down to the xhci
handoff code. It seems that reads from the device occasionally just return
0xff, resulting in xhci_find_next_cap_offset generating a value that's
larger than the resource region. We then oops when attempting to read the
value. Sanity checking that value lets us avoid the crash.

I've no idea what's causing the underlying problem, and xhci still doesn't
actually *work* even with this, but the machine at least boots which will
probably make further debugging easier.

This should be backported to kernels as old as 2.6.31, that contain the
commit 66d4eadd8d067269ea8fead1a50fe87c2979a80d "USB: xhci: BIOS handoff
and HW initialization."

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoxhci: Fix a logical vs bitwise AND bug
Dan Carpenter [Mon, 13 Aug 2012 16:57:03 +0000 (19:57 +0300)]
xhci: Fix a logical vs bitwise AND bug

commit 052c7f9ffb0e95843e75448d02664459253f9ff8 upstream.

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f474f0db3a4d940cae1423783edd966027 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoxhci: Switch PPT ports to EHCI on shutdown.
Sarah Sharp [Mon, 23 Jul 2012 15:59:30 +0000 (18:59 +0300)]
xhci: Switch PPT ports to EHCI on shutdown.

commit e95829f474f0db3a4d940cae1423783edd966027 upstream.

The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS.  If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system.  Some BIOS will work around this, but not all.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.  The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.

Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names.  One example
is Compulab's mini-desktop, the Intense-PC.  Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.

The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Denis Turischev <denis@compulab.co.il>
Tested-by: Denis Turischev <denis@compulab.co.il>
[bwh: Backported to 3.2: adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agostaging: zcache: fix cleancache race condition with shrinker
Seth Jennings [Wed, 29 Aug 2012 21:58:45 +0000 (16:58 -0500)]
staging: zcache: fix cleancache race condition with shrinker

commit 6d7d9798ad5c97ee4e911dd070dc12dc5ae55bd0 upstream.

This patch fixes a race condition that results in memory
corruption when using cleancache.

The race exists between the zcache shrinker handler,
shrink_zcache_memory() and cleancache_get_page().

In most cases, the shrinker will both evict a zbpg
from its buddy list and flush it from tmem before a
cleancache_get_page() occurs on that page. A subsequent
cleancache_get_page() will fail in the tmem layer.

In the rare case that two occur together and the
cleancache_get_page() path gets through the tmem
layer before the shrinker path can flush tmem,
zbud_decompress() does a check to see if the zbpg is a
"zombie", i.e. not on a buddy list, which means the shrinker
is in the process of reclaiming it. If the zbpg is a zombie,
zbud_decompress() returns -EINVAL.

However, this return code is being ignored by the caller,
zcache_pampd_get_data_and_free(), which results in the
caller of cleancache_get_page() thinking that the page has
been properly retrieved when it has not.

This patch modifies zcache_pampd_get_data_and_free() to
convey the failure up the stack so that the caller of
cleancache_get_page() knows the page retrieval failed.

This needs to be applied to stable trees as well.
zcache-main.c was named zcache.c before v3.1, so
I'm not sure how you want to handle trees earlier
than that.

Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agort2800usb: Added rx packet length validity check
Sergei Poselenov [Sun, 2 Sep 2012 09:14:32 +0000 (13:14 +0400)]
rt2800usb: Added rx packet length validity check

commit efd5d6b03bd9c9e0df646c56fb5f4f3e25e5c1ac upstream.

On our system (ARM Cortex-M3 SOC running linux-2.6.33)
frequent crashes were observed in the rt2800usb module
because of the invalid length of the received packet (3392,
46920...). This patch adds the sanity check on the packet
legth. Also, changed WARNING to ERROR in rt2x00lib_rxdone()
so that the bad packet condition would be noticed.

The fix was tested on the latest compat-wireless-3.5.1-1-snpc.

Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agort2x00: Fix rfkill polling prior to interface start.
Gertjan van Wingerde [Fri, 31 Aug 2012 17:22:11 +0000 (19:22 +0200)]
rt2x00: Fix rfkill polling prior to interface start.

commit a396e10019eaf3809b0219c966865aaafec12630 upstream.

We need to program the rfkill switch GPIO pin direction to input at
device initialization time, not only when the interface is brought up.
Doing this only when the interface is brought up could lead to rfkill
detecting the switch is turned on erroneously and inability to create
the interface and bringing it up.

Reported-and-tested-by: Andreas Messer <andi@bastelmap.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agort2x00: Fix word size of rt2500usb MAC_CSR19 register.
Gertjan van Wingerde [Fri, 31 Aug 2012 17:22:10 +0000 (19:22 +0200)]
rt2x00: Fix word size of rt2500usb MAC_CSR19 register.

commit 6ced58a5dbb94dbfbea1b33ca3c56d1e929cd548 upstream.

The register is 16 bits wide, not 32.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agort2x00: Identify ASUS USB-N53 device.
Gertjan van Wingerde [Fri, 31 Aug 2012 17:22:09 +0000 (19:22 +0200)]
rt2x00: Identify ASUS USB-N53 device.

commit 177ef8360fabdc49ff08d2598c06e7f7a36b53e3 upstream.

This is an RT3572 based device.

Signed-off-by: Maximilian Engelhardt <maxi@daemonizer.de>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo Van Doorn <ivdoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoIntel xhci: Only switch the switchable ports
Keng-Yu Lin [Thu, 9 Aug 2012 17:39:23 +0000 (01:39 +0800)]
Intel xhci: Only switch the switchable ports

commit a96874a2a92feaef607ddd3137277a788cb927a6 upstream.

With a previous patch to enable the EHCI/XHCI port switching, it switches
all the available ports.

The assumption is not correct because the BIOS may expect some ports
not switchable by the OS.

There are two more registers that contains the information of the switchable
and non-switchable ports.

This patch adds the checking code for the two register so that only the
switchable ports are altered.

This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agoxhci: Recognize USB 3.0 devices as superspeed at powerup
Manoj Iyer [Wed, 22 Aug 2012 16:53:18 +0000 (11:53 -0500)]
xhci: Recognize USB 3.0 devices as superspeed at powerup

commit 29d214576f936db627ff62afb9ef438eea18bcd2 upstream.

On Intel Panther Point chipset USB 3.0 devices show up as
high-speed devices on powerup, but after an s3 cycle they are
correctly recognized as SuperSpeed. At powerup switch the port
to xHCI so that USB 3.0 devices are correctly recognized.

BugLink: http://bugs.launchpad.net/bugs/1000424
This patch should be backported to kernels as old as 3.0, that contain
commit ID 69e848c2090aebba5698a1620604c7dccb448684 "Intel xhci: Support
EHCI/xHCI port switching."

Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agostaging: vt6656: [BUG] - Failed connection, incorrect endian.
Malcolm Priestley [Wed, 29 Aug 2012 22:08:21 +0000 (23:08 +0100)]
staging: vt6656: [BUG] - Failed connection, incorrect endian.

commit aa209eef3ce8419ff2926c2fa944dfbfb5afbacb upstream.

Hi,

This patch fixes a bug with driver failing to negotiate a connection.

The bug was traced to commit
203e4615ee9d9fa8d3506b9d0ef30095e4d5bc90
staging: vt6656: removed custom definitions of Ethernet packet types

In that patch, definitions in include/linux/if_ether.h replaced ones
in tether.h which had both big and little endian definitions.

include/linux/if_ether.h only refers to big endian values, cpu_to_be16
should be used for the correct endian architectures.

Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agostaging: comedi: das08: Correct AO output for das08jr-16-ao
Ian Abbott [Fri, 31 Aug 2012 19:41:30 +0000 (20:41 +0100)]
staging: comedi: das08: Correct AO output for das08jr-16-ao

commit 61ed59ed09e6ad2b8395178ea5ad5f653bba08e3 upstream.

Don't zero out bits 15..12 of the data value in `das08jr_ao_winsn()` as
that knobbles the upper three-quarters of the output range for the
'das08jr-16-ao' board.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
9 years agostaging: comedi: das08: Correct AI encoding for das08jr-16-ao
Ian Abbott [Fri, 31 Aug 2012 19:41:29 +0000 (20:41 +0100)]
staging: comedi: das08: Correct AI encoding for das08jr-16-ao

commit e6391a182865efc896cb2a8d79e07b7ac2f45b48 upstream.

The element of `das08_boards[]` for the 'das08jr-16-ao' board has the
`ai_encoding` member set to `das08_encode12`.  It should be set to
`das08_encode16` same as the 'das08jr/16' board.  After all, this board
has 16-bit AI resolution.

The description of the A/D LSB register at offset 0 seems incorrect in
the user manual "cio-das08jr-16-ao.pdf" as it implies that the AI
resolution is only 12 bits.  The diagrams of the A/D LSB and MSB
registers show 15 data bits and a sign bit, which matches what the
software expects for the `das08_encode16` AI encoding method.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.2: adjust indentation]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>